FCC ID: J69GENCLBX Call Box Transmitter

Technical Document CB440/CB511 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting the installations. As an un-

programmed callbox defaults to an address of 001, this position in the control unit may be left blank or have an advisory message. Location Considerations Call boxes are generally best located at areas that require assistance to access store merchandise, such as high shelving, chain and rope cutting, key machine, etc. Stores and installers should be aware of Americans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter, and operate best with a clear line of sight to the nearest receiver. Tall shelving, merchandise and metal signs can block or reduce the callbox signal. CB440 (above) and CB511 (right) Install the Call Box 1. Verify call box placement with the Store Manager and determine the best mounting method. Note: Before installing the call box, verify address programming. If mounting the call box to glass display case, affix the double-sided foam tape to the back panel of the call box. If mounting the call box to the wall, affix the Velcro tape to the back panel of the call box. If mounting the call box to a wood surface, open the call box and use the included hardware to secure the call box to the wooden surface. (CB440 only) 2. Install the back panel with the provided hardware. Programming CB440/CB511 Call Box Address NOTE: IF INSTALLED, JUMPER JP2 MUST BE REMOVED DURING PROGRAMMING. WHEN POWERED UP, THE CALL BOX WILL DEFAULT TO 001. The Address and Mode for each call box are listed in the Store Installation and Operation Manual for the specific store install. Refer to the data tables in Appendix A of the Store Installation and Operation Manual for the correct Mode and Address for each call box you are programming. 1. Press and hold the RESET button for approximately 5 seconds. 2. LED 1 will flash to indicate the call box is in address programming mode. 3. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. 4. Press the RESET button when finished with the hundreds digit. 5. Press button 1 to increment the tens digit. LED 1 will flash with each press. CB440/511 Install Instructions 1 P/N: 430223-00 Rev H Technical Document 6. Press the RESET button when finished with the tens digit. 7. Press button 1 to increment the ones digit. LED 1 will flash with each press. 8. Press the RESET button when finished with the ones digit. 9. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on for a longer period of time, approximately 1 second). JP1 Power: must be installed during call box programming. JP4 Pulse Width: must be installed for Narrow Pulse Width operation and programming. JP2: NOT installed during call box programming. JP3 Mode Program Enable: must be installed during call box programming. Revised PCA for CB440 and CB511 Mode Summary:

The new CB440/511 Call Box PCA has seven operating modes as in TSN001: Wireless Call Boxes. For normal installation, each call box is programmed at the factory. If it becomes necessary to re-program the call box, please refer to the TSN001 in the Store Installation and Operation Manual for additional programming features and requirements. If the manual is not available, please contact the Indyme Help Desk at 800-829-6141 for additional support. Note: older models of these call boxes are not "Mode" programmable. Before programming these call boxes, identify what model of circuit board is installed in the unit as per the serial number or the PCA illustration above. FCC Notice Of Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CB440/511 Install Instructions 2 P/N: 430223-00 Rev H

Technical Document CB514 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting the installations. As an un-

programmed callbox defaults to an address of 001, this position in the control unit may be left blank or have an advisory message. Location Considerations Director call boxes are generally best located in high volume areas that demand a way to request additional services quickly, such as front registers or service counters. Stores and installers should be aware of Americans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter, and operate best with a clear line of sight to the nearest receiver. Tall shelving, merchandise and metal signs can block or reduce the callbox signal. Install the CB514 Call Box 1. Verify call box and clear plastic label sleeve placement with the Store Manager. (The label sleeve is optional and may not be used in all applications.) 2. Identify which side of the CB514 the label sleeve should be attached for the best visibility and avoiding damage (the sleeve can be mounted on the left or right side of the call box). 3. Slide the label into the clear plastic sleeve (double-sided tape or Velcro will be installed on the bottom of the label sleeve). Programming the CB514 Call Box To program the CB514, program the first button and the remaining three buttons are automatically programmed with the next numerical values. When the call box "flashes" the newly programmed address, the zero value will be indicated by a longer (slightly over a second) flash. For example: an address of 001 would be shown as long flash (0), pause, long flash(0), pause, and a short flash (1). NOTE: IF INSTALLED, JUMPER JP2 MUST BE REMOVED DURING PROGRAMMING. WHEN POWERED UP, THE CALL BOX WILL DEFAULT TO 001. The Address and Mode for each call box are listed in the Store Installation and Operation Manual for the specific store install. Refer to the data tables in Appendix A of the Store Installation and Operation Manual for the correct Mode and Address for each call box you are programming. 1. Press and hold the RESET button for approximately 5 seconds. 2. LED 1 will flash to indicate the call box is in address programming mode. 3. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. 4. Press the RESET button when finished with the hundreds digit. CB514 Install Instructions 1 P/N: 430223-01 Rev B Technical Document 5. Press button 1 to increment the tens digit. LED 1 will flash with each press. 6. Press the RESET button when finished with the tens digit. 7. Press button 1 to increment the ones digit. LED 1 will flash with each press. 8. Press the RESET button when finished with the ones digit. 9. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on for a longer period of time, approximately 1 second). JP1 Power: must be installed during call box programming. JP4 Pulse Width: must be installed for Narrow Pulse Width operation and programming. JP2: NOT installed during call box programming. JP3 Mode Program Enable: must be installed during call box programming. Mode Summary:

Revised PCA for CB514 The new CB514 Call Box PCA has seven operating modes as defined in TSN001:

Wireless Call Boxes. For normal installation, each call box is programmed at the factory. If it becomes necessary to re-program the call box, please refer to the TSN001 in the Store Installation and Operation Manual for additional programming features and requirements. If the manual is not available, please contact the Indyme Help Desk at 800-829-6141 for additional support. Note: older models of these call boxes are not "Mode" programmable. Before programming these call boxes, identify what model of circuit board is installed in the unit as per the serial number or the PCA illustration above. FCC Notice Of Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CB514 Install Instructions 2 P/N: 430223-01 Rev B

INDYME. Technical Document CB440/CB511 Installation And Programming Instruction Individual calloox addresses should be determined prior to starting the installations. programmed callbox defaults to an address of 001, this position in the control unit ma or have an advisory message. Location Considerations Call boxes are generally best located at areas that require assistance to access store merchandise, such as high shelving, chain and rope cutting, key machine, etc. Stores and installers should be aware of Americans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter, and operate best with a clear line of sight to the near st receiver. Tall shelving, merchandise and metal signs reduce the callbox signal. Install the Call Box 1. Verify call box placement with the St method. Note: Before installing the call B511 Cail Box Address ess and Mode for each call box are listed in the Store Installation and ition Manual for the specific store install. Refer to the data tables in Appendix A of Store Installation and Operation Manual for the correct Mode and Address for each Il box you are programming. Press and hold the RESET button for approximately 5 seconds. LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. ahons CB440/511 Install Instructions 1 P/N: 430223-00 Rev H INDYME Technical Document Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying o longer period of time, approximately 1 second). o ON JP1 Power: must be installed :

during call box programming. Pulse Width operation an Mode Program Enable: must be installed during call box programming. PCA for CB440 and CB511 Box PCA has seven operating modes as in TSNO01: Wireless stallation, each call box is programmed at the factory. If it 141 for additional support.

; older models of these call boxes are not "Mode" programmable. Before programming these all boxes, identify what model of circuit board is installed in the unit as per the serial number or he PCA illustration above. FCC Notice Of Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CB440/511 Install Instructions 2 P/N: 430223-00 Rev H INDYME Technical Document CB475 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting call box installations. As programmed callbox defaults to an address of 001, this position in the control unit may be. or have an advisory message. Installing CB475 Call Boxes Location Considerations Call boxes are generally best located at areas that require assi access store merchandise, such as: high shelving, chain key machines. Stores and installers should be aware Disabilities Act (ADA) requirements for accessibility. The CB475 call boxes utilize a very low powered transmitter, best with a clear line of sight to the neare Tall shelving merchandise and metal signs can block. Install the Call Box 1. For ADA compliant locations, floor. Mark this heigh bracket. (See th document. 2. Deterr 0200-20) to secure the bracket to the mounting surface. If necessary, drill 0 pilot holes using a 5/32 bit, then install the self-tapping TEK screws. For masonry mounting: Mark the bottom bracket holes, using the two holes furthest from one another. Use a 4 masonry bit and drill a hole deep enough

(approximately 1") for the green plastic masonry anchors (p/n: 180064-00). Install the masonry anchors, and secure the bracket with provided anchor-

SCrews . 3. Install the top mounting bracket using the same hardware and technique as used for the bottom bracket. Measure up 24 from the middle of the installed bottom bracket and position the middle of the top bracket here. A level should be used to insure that the installed callbox will be plumb. 4. Start one slotted hex-washer head screw (p/n: 180066-00) in each bracket. CB475 Install Instructions 1 P/N: 430262-00 Rev E INDYME Technical Document CB475 Installation And Programming Instruction individual callbox addresses should be determined prior to starting call box installations. As programmed callbox defaults to an address of 001, this position in the control unit may be. or have an advisory message. Installing CB475 Call Boxes Location Considerations Call boxes are generally best located at areas that require assi access store merchandise, such as: high shelving, chain key machines. Stores and installers should be aware Disabilities Act (ADA) requirements for accessibility. The CB475 call boxes utilize a very low powered transmitter, best with a clear line of sight to the neare Tall shelving merchandise and metal signs can block Install the Call Box 1. For ADA compliant locations, e locations on the wall. Use the provided self-tapping TEK screws (p/n:

0200-20) to secure the bracket to the mounting surface. If necessary, drill wo pilot holes using a 5/32 bit, then install the self-tapping TEK screws. For masonry mounting: Mark the bottom bracket holes, using the two holes furthest from one another. Use a 4 masonry bit and drill a hole deep enough

(approximately 1") for the green plastic masonry anchors (p/n: 180064-00). install the masonry anchors, and secure the bracket with provided anchor-

Screws . 3. Install the top mounting bracket using the same hardware and technique as used for the bottom bracket. Measure up 24 from the middle of the installed bottom bracket and position the middle of the top bracket here. A level should be used to insure that the installed callbox will be plumb. 4. Start one slotted hex-washer head screw (p/n: 180066-00) in each bracket. CB475 Install Instructions 1 P/N: 430262-00 Rev E INDYME Technical Document 5. Install the signs (if not already installed) into the sign extrusion. Install the top and bottom caps. 6. Install the call box by sliding it over the brackets. Position the bottom of the callbox flush with the lower edge of the bottom bracket. Verify the red antenna wire (from the PCA inside the call box) is routed up the back, inside of the sign blade. 7. Firmly tighten the slotted hex-washer head screw with a nut-driver. The scre:

not have to be extremely tight to hold the callbox. i} Top bracket TOP Self-taping pinch screw installation Finished floor, height ing Diagram Programmin all box are listed in the Store Installation and Operation Manual sr to the data tables in Appendix A of the Store Installation and Press and hold the RESET button for approximately 5 seconds. LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. 3. 4. 5. 6. 7. 8. rr A CB475 Install Instructions 2 P/N: 430262-00 Rev E INDYME Technical Document 9. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on for a longer period of time, approximately 1 second). JP1 Power: must be installed JP4 Pulse Width: must be installed for Narr. during call box programming. Pulse Width operation and programmi aim Enable: must be

} call box programming. JP2: NOT installed dut call box programming. Mode Summ. els ese call boxes are not "Mode" programmable. Before programming these ify what model of circuit board is installed in the unit as per the serial number or subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. i TT NST CB475 Install Instructions 3 P/N: 430262-00 Rev E INDYME Technical Document CB514 Installation And Programming Instruction individual callbox addresses should be determined prior to starting the installations. As an un-

programmed callbox defaults to an address of 001, this position in the control unit may b blank or have an advisory message. Location Considerations Director call boxes are generally best located in high volume areas that demand a way to request additional services quickly, such as front registers or service counters. Stores and installers should be aware of Americans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter, and. best with a clear line of sight to the nearest receiver. Tall merchandise and metal signs can block or reduce the call signal. Install the CB514 Call Box 1. Verify call box and clear plastic lab sleeve is optional and may not be used ore Manager. (The label 2. attached for the best visibility ed on the left or right side of the call box). ble-sided tape or Velcro will be installed on

. jutton and the remaining three buttons are automatically ical \ values. When the call box "flashes" the newly programmed icated by a longer (slightly over a second) flash. For example: an ong flash (0), pause, long flash(0), pause, and a short flash (1). Mode for each call box are listed in the Store Installation and Operation specific store install. Refer to the data tables in Appendix A of the Store nd Operation Manual for the correct Mode and Address for each call box you are ing. Press and hold the RESET button for approximately 5 seconds. LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. 1. 2. 3. 4. 5. CB514 Install Instructions 7 P/N: 430223-01 Rev B en a INDYME Technical Document Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on for a longer period approximately 1 second). Oo OND JP1 Power: must be installed JP4 Pulse Width: must be ins during call box programming. Pulse Width operation and JP2: NOT installed duri d PCA for CB514 PCA has seven operating modes as defined in TSNOO7:

der models of these call boxes are not "Mode" programmable. Before programming these oxes, identify what model of circuit board is installed in the unit as per the serial number or PCA illustration above. FCC Notice Of Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CB514 Install Instructions 2 P/N: 430223-01 Rev B

4.2 PROGRAMMING THE NEW CB440, CB475, CB511 AND CB514 The Address and Mode for each call box are listed in the Store Installation and Operation Manual for the specific store install. Refer to the data tables in Appendix A of that manual for the correct Address and Mode for each call box you are programming. Note: earlier models of these call boxes are not "Mode" programmable and do not have JP4. Before programming a new call box, identify what version of circuit board is installed in the unit per the serial number on the unit or the illustration below .(Note: Only boards with JP4 present can be programmed for Narrow Pulse Mode.) Address Programming:

Press and hold the RESET button for approximately 5 seconds. LED 1 will flash when the RESET button has been held down long enough. The system is now in address programming mode. (Note: if installed, jumper JP2 must be removed during programming as it will disable the programming of the address). Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. The address that you just programmed in should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on for a longer period of time, approximately 1 second). NAM WNP JP1 Power: must be installed JP4 Pulse Width: must be installed for Narrow during call box programming. Pulse Width operation and programming. JP2: NOT installed during JP3 Mode Program Enable: only call box programming. installed during call box programming. Mode Programming:

CB440/475/511/514 Call Box PCA call boxes have two possible pulse width settings:

Narrow Pulse Width or Wide Pulse Width. The Pulse Width Programming is enabled TSNOO1 - Wireless CB's 6 P/N: 435001-00 Rev. E depending on the jumper position of JP4 on the call box circuit board and is identified by the second digit of the Mode Programming. Default setting for JP4 is jumper on both pins. Call boxes programmed with "Narrow Pulse Width Mode Enabled", will only work with a CB451B Receiver. Jumper must be installed on JP4.

* Call Boxes programmed with "Wide Pulse Width Mode Enabled", will work with a CB451A Receiver or a CB451B Receiver. No jumper on JP4. Note: The receiver type is easily identified by the color of the operation LED. CB451A has a green operation LED and CB451B has a red operation LED. Mode Summary Mode 1 - Standard Call Box with 8 minute Timeout (4 programmable channels) Press the channel (HELP) button to trigger the call box. The LED next to the HELP button flashes and then extinguishes after approximately 8 minutes if the RESET button

(small white circle) is not pressed. Channel 4 is programmed as an External input. When a valid input (momentary only) is received, it transmits a call box "Channel 4" transmission to the MTS. When alarm state is removed, no reset is sent. When pressed, the RESET button will reset (or clear) the call box . Mode 2 Call Box with 30 second Timeout (4 programmable channels) Press the channel (HELP) button to trigger the call box. The LED next to the channel

(HELP) button flashes and then turns off after approximately 30 seconds if the RESET button (small white circle) is not pressed. Channel 4 is programmed as an External input. When a valid input (momentary only) is received, it transmits a call box "Channel 4" transmission to the MTS. When alarm state is removed, no reset is sent. When pressed, the RESET button will reset (or clear) the call box . Mode 3 Ext Momentary Switch Call Box w/8 min Timeout (1 programmable channel) Press the channel (HELP) button to trigger the call box. The LED next to the channel button flashes, then extinguishes after approximately 8 minutes if the RESET button

(small white circle) is not pressed. Channel 1 is programmed for an External momentary input and transmits as a call box

"channel 1" signal to the MTS. When alarm state is removed, no RESET is sent. When pressed, the RESET button will reset (or clear) the call box . Mode 4N/O (Normally open) Switch Contact Call Box (1 programmable channel) External input (closed) is used to trigger the call box. When activated, the LED begins to flash, then extinguishes after approximately 30 seconds. Channel 1 is programmed as an External momentary input and transmits as a standard call box "Channel 1" SET. When alarm state is removed, a RESET is sent.

* Mode 5 N/C Switch Contact Call Box (1 channel max) External input (open) is used to trigger the call box. When activated, the LED begins to flash, then extinguishes after approximately 30 seconds. TSNOOI - Wireless CB's 7 PIN: 435001-00 Rev. E Channel 1 is programmed as an External momentary input and transmits as a standard call box "Channel 1" SET. When alarm state is removed, a RESET is sent. Mode 6 - CU3000 Compatible 8 min timeout (4 programmable channels) Mode 1 is compatible with CU3000 systems. This mode will not send a supervisory transmission, but will send a RESET transmission at 8 minutes and battery status. Mode 7 - Standard Call Box with Acknowledge (4 channels max) Press the channel (HELP) button to trigger the call box. The LED flashes. If the same channel (HELP) button is not pressed again, the LED continues to flash for approximately 8 minutes, then extinguishes with no reset transmissions sent. If the same channel (HELP) button is pressed a second time, the LED decreases the flash rate and an Acknowledge transmission is sent to the MTS. The LED flashes for approximately 8 minutes, then extinguishes with no reset sent . The External input is a valid input (momentary only) and transmits call box channel 1. If alarm state is removed, no reset is sent. When pressed, the RESET button will reset (or clear) the cail box . Programming CB440/475/511/514 Call Box Mode And Pulse Width Values:

Before programming the call box, the call box must be open and the jumpers moved to accommodate programming sequences. 1. 2. 3. nin oN TSNOO1 - Wireless Verify jumper JP4 is set correctly. (on both pins for Narrow Pulse, off for Wide Pulse) Install the jumper on both pins of JP3 (next to the battery). Press the RESET button to determine the current mode setting. The current Mode and Pulse Width value will flash back on LED 1. Press Button 1 "X" times to program the Mode (Modes 1-7 are available). LED 1 will light for each press. Press the RESET button to save the new Mode value Press Button 1 to program Pulse Width: press once for Narrow Pulse Width or press twice for Wide Pulse Width. Press RESET to save the new Pulse Width value. The Mode and Pulse Width values will flash back on LED 1: Mode, pause, Pulse Width. Remove the jumper from JP3 and re-install the back panel. Note: failure to remove JP3 before standard call box operation will prevent the call box from operating properly. Note: Narrow Pulse Width is available only when using a CB451B Receiver. Install the JP4 jumper. Jumper JP4 is installed by default at the factory. Jumper both pins of JP3. Press Button 1 twice (for Mode 2). Button #1 LED will flash for each press. Press RESET. Press Button 1 one time (for Narrow Pulse Width), the LED will flash once. Press RESET. Watch as Button 1 LED flashes twice (for Mode 2), pauses, and then flashes once (for "Narrow Pulse Width"). Remove the jumper from JP3. Do not remove the jumper from JP4. AMP WNP PIN: 435001-00 Rev. E Remove the JP4 jumper. Jumper both pins of JP3. Press Button 1 twice (for Mode 2). Button #1 LED will flash for each press. Press RESET. Press Button 1 twice (for Wide Pulse Width). LED1 will flash for each press. Press RESET. Watch as Button 1 LED flashes two times (for Mode 2), pauses, and then flashes twice (for "Wide Pulse Width"). Remove the jumper from JP3. Do not install a jumper on JP4. AMP WNP

4.3 PROGRAMMING THE CB440, CB475, CB511, AND CB514 (PRE-2002) The earlier versions (older PCA) of these particular call boxes are all programmed similar. The Address and House Code for each call box is listed in the Store Installation and Operation Manual for the specific store. Refer to the data tables in Appendix A of that manual for the correct Address and House Codes for each call box you are programming. The Address and House Code, when combined, is typically identified as a three-digit number such as: 2-3-1. To Program a Call Box:

Press and hold the RESET button until the SET Button LED comes on. Then enter the new Call Box programming by following the steps below. 1. Press the SET Button x number of times to program the 1st digit. (First digit of call box button address) 2. Press RESET. 3. Press the SET Button x number of times to program the 2nd digit. (Second digit of call box button address) 4. Press RESET. 5. Press the SET button x number of times to set the House code digit. 6. Press RESET. The Call Box will blink out the newly programmed code and exit to operate mode. To read an existing code:

Press and hold the RESET button until the SET button LED comes on. Press the RESET button again, the programmed code will be blinked out and the Call Box will resume normal operating mode. BUTTON CODES:

Call Box button codes range from 1-1 to 8-8. Overflow results in wrapping around, for example, if you press the button 10 times, it will program as a 2 (10-8=2). HOUSE CODES:

The third digit programmed is the HOUSE CODE, it must match the control unit's HOUSE CODE. For older systems, the house code equivalents are listed below. In most cases, the house code will remain at he 12 (or 1). 1 =he 12 2 =he 54 3 =hc 45 4 =hce 20 5=hc6A ip i TSNOO1 - Wireless CB's 9 PIN: 435001-00 Rev. E