FCC ID: O34-E790GPRS Elite 790 GPRS

Make sure that you use the correct AC power adapter supplied with the terminal. Many adapters can appear similar and will plug into the terminal but will not work properly causing erratic behavior, poor charging or even damage to the unit. 2.4.2 Normal use:

1. After a full charge the Terminal in normal usage is expected to provide 50 or more transactions before the terminal has to be returned to the base for charging. Slow printing or a message <<-BAT->>

on the display followed by beep usually indicates the battery is low 2. This terminal has a reserve capability in the event that more transactions are occasionally needed. As long as the print time is acceptable the Terminal will provide additional transactions beyond normal. The effect will be continued slowdown of the printer as well as a longer recharge cycle. 3. Do not use a Fast Charging Base if the terminal is returned to the base after each transaction. The batteries may be damaged and their life time reduced. A fast charging base should be used to charge battery pack ONLY when there is slow printing or a message <<-BAT->> displays otherwise use slow charging base. 3. Cleaning procedure:

1. Clean the outside of the terminal with a soft cloth moistened with a mild detergent solution. 2. Never spray cleaning solution directly onto the terminal as drops may enter the unit. 3. Do not use Isopropyl Alcohol based cleaning products. 4. Technical specifications:

4.1 Terminal Features:

Magnetic card reader, ISO1 and ISO2 tracks decoding. 18 key, backlit tactile feedback keyboard with audible tone and color coding. Battery backed-up calendar and clock. RS232 communications channel. Logical and physical security. Multi-application operating system allowing each application to be downloaded independently of all others. 4.2 Network:

The terminal is equipped with an RF modem for exchanging data over one of the following networks:

1. Rogers Network. 2. CDPD 4.3 Power supply:

The power adapter is mainly used for charging the internal NiMh battery. Power input voltage : 100-220V AC. Power input frequency : 50-60 Hz. Power output

: 11V DC, 1.5A Figure 4: DC Plug 4.4 Operating environment Operating temperature : 5 to 40C Humidity: 5% to 90% RH, with no condensation. 5. Thermal Paper Specification:

The following specifications identify the thermal paper roll that must be used with Elite 790 Terminals:

Single ply thermal sensitive - POS or facsimile grade. Basis Weight:

(lb/rm 17 ins. X 22 ins. - 500) --- 14.5 +/- 5%

(GSM) --- 55 +/- 5%

Smoothness (Bekk Minimum): 300 s Caliper: 2.4 +/- 0.2 Mils or 60 +/- 5 Microns Brightness: Min. 85%

Roll Width: 2.25 +/- 0.020 in (58 mm +/- 0.5 mm). Roll Diameter: 2.0 in (51 mm) maximum. Roll Core ID: 0.500 in (13 mm) nominal. Roll Core OD: 0.625 in (16 mm) nominal. For best performance, Ingenico recommends The following sources/barnds:

KANZAKI P300 APPLETON T1012A KOEHLER K55 Elite 790 Installation Guide 0130-00031-0100 5.1 Storage Recommendation for Thermal Paper:

Thermal paper should NOT be exposed to vinyl, Plastics, adhesives, shrink-wraps, wet-toner copies or certain carbon papers, office light, UV light, high humidity and temperature (above 65%, 25C) for long periods of time. 7. If you experience problems :

Call one of the customer service centers listed below:

(FCC) In the USA:

Ingenico Inc. TotalCARE 1335North Meadow Parkway, Suite 116 Atlanta GA 30076 In Canada:

RBA Inc. 3190 Orlando Drive Mississauga, Ontario L4V 1R5 1-800-387-3938 or (905) 672-1048 1-800 435-3014 US Federal Communications Commission Warnings:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Canadian Department of Communications Warnings:

This digital apparatus does not exceed the Class A limits for radio noise emissions from the digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. cause harmful interference

(DOC) to Ingenico Inc. 1003 Mansell Road, Atlanta, GA 30076 Tel: 770.594.6000 Fax 770.594.6003 www.ingenico-us.com Ingenico Canada Ltd. 79 Torbarrie Road, Toronto, Ontario Canada M3L 1G5 Tel:416.245.6700 Fax: 416.245.6701 www.ingenico-ca.com Paper Load Lever Roll Release Lever 4. Position the paper roll with the end of the roll protruding from UNDERNEATH the roll. 5. Feed the paper under the printers roller until it protrudes from the top of the printer. 6. Fit the paper roll to the spindle and move the paper load lever back to engage the friction roller. 7. Close the cover and test the operation of the printer by Pressing Paper Feed key. 2.2 SIM Installation:

Access to the optional SIM slots is through the battery Door located on the underside of the terminal. Access to GSM SIM is through a trap door which slides only When the battery pack is removed. ADMIN key:

is used to access administration function menu. 1.2.3 Magnetic Stripe Card Reader:

the terminal 1. Terminal description:

1.1 Introduction:

integrated printer and The Elite 790 is a fully self-contained RF EFTPOS terminal with an the functionality to process all smart card, debit and credit purchases. The terminal communicates with the bank using the RF data network or using Fast Charging or Slow Charging Base through Telephone network. This RF network is similar to that used for mobile phones except that it is for data only. The terminal secure, multi-application operating system, which allows a number of different applications terminal independently, without software security. the jeopardizing to run on features a 1.2 The Terminal:

The Elite 790 terminal has the following peripherals:

1.2.1 Display:

Standard 4 line x 16 character LCD graphic display, with back lighting. 1.2.2 Keypad:

18 keys, with back lighting, with the following special function keys:

F1, F2, and F3 keys: Programmable keys which permit access to terminal level functions and the system menu. Paper Feed key: Performs a 20mm paper feed. ENTER key: is used to confirm the data entered or CAN key: is used to cancel the current function and return the terminal to the idle state. CORR key: is used to correct any invalid data displayed. entry. This is a bi-directional reader capable of simultaneously reading Tracks 1&2, and is located just above the display. The Magnetic Stripe on the card should face down and to the rear of the terminal. The card should be swiped at uniform speed and pressure, ensuring that the card remains in contact with the bottom of the track throughout the entire swipe action. 1.2.4 Modem:

The Modem facilitates data exchange over an RF network. 1.2.5 Printer:

The built-in printer is a high-speed thermal printer (6 lines per second) and is graphics compatible. 1.2.6 Smart Card Reader:

Complies with standard ISO 7816, Sync & Async. The terminal is equipped with a Smart Card Reader slot at the front of the terminal for future use. 1.3 The Slow/Fast Charging Base:

There are slow or fast charging base. They have two functions:

- Used as interface of telephone network communication and downloading applications.

- Used as interface of alimentation (recharge battery and direct power). 1.4 Package may contents are as follows:

1. The Elite 790 terminal. 2. Desk top power adapter for charging the Ni-Mh battery. 3. Slow or Fast charging base. 4. Thermal printer paper, one roll. 5. Installation guide. 2. Installation procedure:

Important Note: Before using the terminal for the

first time, the battery pack must be fully charged. This is indicated by a green light on the base which TURNS OFF when battery pack is fully charged.

(See Paragraph 2.4) 2.1 Paper loading (If required):

1. Open the paper compartment cover. 2. Move the paper load lever forward to disengage the friction roller. 3. Remove the empty paper roll by pressing the roll release lever on the right hand side. GSM SIM SIM No 1 To unlock the SIM holder, slide the metal clasp away from the center of the unit. Swing the SIM holder up. Insert the SIM card in between the metal clasp and the plastic holder, with metal plate facing down. Swing the SIM holder down. To lock the SIM card in place, slide the metal clasp in toward the center of the unit. 2.3 Base Connection

. The telephone TELEPHONE CONNECTION The compact telephone cable connection supplied with the Elite terminal must be connected to the port Marked with the symbol connection (RJ11) must be connected to the telephone socket in the wall. ELECTRICAL CONNECTION The small jack connection to the power pack is plugged into the port market with the symbol The twin pronged electrical plug is connected into wall electrical socket. CONNECTION TO AN EXTERNAL DEVICES Some peripheral devices such as a cheque readers can also be connected. The ELITE 790 terminal must be powered off before connecting the cable on the base to the RS232 port. 2.4 Battery charging procedure:

2.4.1 Charging the battery pack:

1. After unpacking it is important to provide an initial charge. This conditioning cycle is required for the battery pack to reach full capacity quickly. 2. Connect the AC power to the slow or fast charging base using the supplied power pack designed for this terminal. Place the Elite 790 terminal or standalone battery pack on top of the slow or fast charging base. The terminal will power-up and remain on throughout the charging period. The green indictor at front of the base turns off once terminal or standalone battery pack is fully charged.

Integra March 2002/ version 1.6 Version :

Date :

Reference :

1.7 March 2002 WM_Integra_UG_016 1/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Date/ Date History of the evolution /

Historique des volutions June 2000 Creation and Correction Sept. 2000 Correction: figure 5 application note for serial link Application note for external SIM 3V/5V interface Sept 2000 Minor January formal modifications + addition of specifications 2001 SIM3/5V electric scheme added + modification flat cable August 2001 reference March 2002 Modifications to include 2C-2 module version March 2002 Add RF exposure and OEM instructions the mechanical Writer / Rdacteur P. Calvez, S. Dechicha F. Doherier, T. Lapousterle, M. Nau, D. Martinez, B. Zenou S. Dechicha S. Dechicha M. Nau S. Marion N. Subiger O. Clerc Level/

Indice 0.3 1.2 1.3 1.4 1.5 1.6 1.7 Name / Nom Written by / Rdig par B.Zenou Function /

Fonction Product Marketing Validated by / Valid par D. MARTINEZ Modem Support Engineer Approved by / Approuv par P.Calvez Product Marketing Senior Manager Date/ Date Signature/ Signature June 2000 June 2000 June 2000 2/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Integra Users Guide Hardware Specifications 3/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Contents 1 Introduction to the Integra: outstanding assets ........................................................................................................................7 1.1 Scope of the users guide ............................................................................................................7 1.2 General characteristics ................................................................................................................8 1.2.1 General.....................................................................................................................................8 1.2.2 Electrical ...................................................................................................................................8 1.2.3 Physical ....................................................................................................................................8 1.2.4 Basic Features..........................................................................................................................8 1.2.5 Interfaces..................................................................................................................................9 1.3 Mechanical Design Overview ....................................................................................................10 Safety precautions ..................................................................................................................................................................................13 2 2.1 RF safety....................................................................................................................................13 2.1.1 General...................................................................................................................................13 2.1.2 Exposure to RF energy...........................................................................................................13 2.1.3 Efficient modem operation......................................................................................................13 2.1.4 Antenna care and replacement ..............................................................................................13 2.2 General safety ...........................................................................................................................14 2.2.1 Driving.....................................................................................................................................14 2.2.2 Electronic devices...................................................................................................................14 2.2.3 Vehicle electronic equipment .................................................................................................14 2.2.4 Medical electronic equipment.................................................................................................14 2.2.5 Aircraft ....................................................................................................................................14 2.2.6 Children ..................................................................................................................................14 2.2.7 Blasting areas.........................................................................................................................14 2.2.8 Potentially explosive atmospheres .........................................................................................15 2.3 Safety standards........................................................................................................................15 3 Standard Compliance ............................................................................................................................................................................15 3.1 GSM compliance .......................................................................................................................15 3.2 FTA Compliance ........................................................................................................................16 3.2.1 IMEI Number ..........................................................................................................................16 3.2.2 CE Label.................................................................................................................................17 Hardware Interfaces...............................................................................................................................................................................18 4 4.1 Interfaces on the 50-pin general purpose connector................................................................18 4.1.1 The 50-pin connector description ...........................................................................................18 4.1.2 Power supply ..........................................................................................................................22 4.1.3 Serial link ................................................................................................................................24 4.1.4 ON / ~OFF..............................................................................................................................25 4.1.5 BOOT......................................................................................................................................27 4.1.6 Reset signal (~RST) ...............................................................................................................28 4.1.7 Flashing LED ..........................................................................................................................29 4/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 4.1.8 General Purpose Input/Output ...............................................................................................29 4.1.9 Analog to Digital Converter ....................................................................................................29 4.1.10 Audio Interface........................................................................................................................31 4.1.11 SIM interface...........................................................................................................................35 4.1.12 SPI bus ...................................................................................................................................37 4.1.13 Keypad interface.....................................................................................................................37 4.2 RF Interface ...............................................................................................................................39 4.2.1 RF connector ..........................................................................................................................39 4.2.2 RF performances....................................................................................................................39 4.3 SIM interface..............................................................................................................................39 5 Connector Supplier and Peripheral devices ............................................................................................................................ 40 5.1 Where to find the SMD connectors............................................................................................40 5.1.1 GSM Antenna .........................................................................................................................41 5.1.2 The SIM card holder...............................................................................................................42 6 7 Climatic and mechanical environment....................................................................................................................................... 42 Demonstration board............................................................................................................................................................................ 43 General guidelines for the use of the Integra.......................................................................................................................... 44 8 8.1 Key information..........................................................................................................................44 8.1.1 Hardware and RF ...................................................................................................................44 8.1.2 The Antenna ...........................................................................................................................44 8.1.3 Firmware upgrade ..................................................................................................................44 8.1.4 Getting started ........................................................................................................................45 9 10 11 Reference documents .......................................................................................................................................................................... 46 Acronyms and Abbreviations.............................................................................................................................................................47 Index 48 Annexes 53 12 12.1 Mechanical specifications.......................................................................................................53 3V/5V SIM management ........................................................................................................54 12.2 12.3 AT command list.....................................................................................................................54 13 14 RF exposure instructions ....................................................................................................................................................................59 Instructions to OEM ................................................................................................................................................................................60 5/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra Cautions:

Information furnished herein by Wavecom are accurate and reliable. However no responsibility is assumed for its use. Please read carefully the safety precautions. If you have any technical questions regarding this document or the product described in it, please contact your distributor. General information about Wavecom and its range of products is available at the following internet address: http://www.wavecom.com Trademarks Some mentioned products are registered trademarks of their respective companies Copyright The Integra users guide is copyrighted by Wavecom SA with all rights reserved. No part of this users guide may be produced in any form without the prior written permission of Wavecom SA. No patent liability is assumed with respect to the use of the information contained herein. 6/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 1 Introduction to the Integra: outstanding assets Integra M2100 series integrated modem provides a quick and easy way to plug in GSM and GPRS functionality to systems and terminals. Available in dual-band configurations, this full type approved integrated modem constitutes a self-contained, fully integrated implementation of the GSM/GPRS standard. Thanks to standard interfaces, it can be integrated into any system which offers unlimited assets. It is ready for voice, SMS, data and fax. Integra is a product with a sole connector, which puts together all the interface signals in order to facilitate its integration. It has an integrated SIM connector as well as a standard RF connector type MMCX (Miniature Micro Connector). For system integrators, Integra is the fast track to the wireless world. 1.1 Scope of the users guide This document describes the hardware interface and the technical specifications of the Integra M2100 series modem. The integrated modem is referenced as Integra according to the GSM/GPRS 900 standard, the GSM/GPRS 1800 standard and the GSM/GPRS 1900 standard. This product is based on a Dual Band WISMOTM: every integrated modem referenced Integra-G900/1800 includes a GSM 900/1800 MHz module and every integrated modem referenced Integra-G900/1900 includes a GSM 900/1900 MHz module. This two dual-band modems have the same specifications unless otherwise specified. Integra has two version, one GSM only and one GSM/GPRS. The GSM and GSM/GPRS versions have the same specifications unless otherwise specified. 7/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 1.2 General characteristics 1.2.1 General Dual Band GSM/GPRS modem E-GSM 900/1800 or E-GSM 900/1900 Class 4 (2W at 900MHz) Class 1 (1W at 1800/1900 MHz) Small size and low power consumption Voice, SMS Tricodec (FR/EFR/HR) Easy remote control by AT commands for dedicated applications Fully Type Approved according to GSM Phase 2+ specifications Fully shielded and ready-to-use fax and data transmission without extra hardware Internal 3V SIM interface 1.2.2 Electrical Power supply: 5 VDC +/- 5% 1A 310 mA average in GSM 900 at Tx power max 2W 410 mA average in GSM/GRPS 900 at Tx power max 2W 9 mA in idle mode 1.2.3 Physical Absolute maximum dimension: 46 x 64 x 12 mm Weight: 90 g Volume: 36.21 cm3 Casing: Complete shielding-stainless steel-

Mounting: 4 screw holes Operating temperature range: -20C to + 55C Storage temperature: -35C to +85C 1.2.4 Basic Features 1.2.4.1 telephony Telephony (TCH/FS) & Emergency calls Full Rate, Enhanced Full Rate and Half Rate Dual Tone Multi Frequency function (DTMF) 8/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 1.2.4.2 Short Message Service (GSM and GPRS mode) Text and PDU Point to point MT & MO SMS Cell Broadcast 1.2.4.3 GSM circuit Data Features Data circuit asynchronous, transparent and non transparent up to 14,400 bits/s Automatic fax group 3 (Class 1 & 2) Alternate speech and fax MNP2, V.42bis 1.2.4.4 GPRS Packet Data Features GPRS Class 2 Coding Schemes: C1S1 to CS4 Compliant with SMG31bis GSM Supplementary services 1.2.4.5 Call Forwarding Call Barring Multiparty Call Waiting and Call Hold Calling Line Identity Advice of Charge USSD Closed User Group Explicit Call Transfer Other features 1.2.4.6 ME+SIM phone book management Fixed Dialling Number SIM Toolkit Class 2 SIM, network and service provider locks Real Time Clock Alarm management Software upgrade through Xmodem protocol UCS2 character set management Interfaces 1.2.5 Single antenna interface Internal SIM interface:

External SIM interface:

For Data Operation:

3V only 3V only for engineering sample. 3V or 5V for production unit RS-232C serial link remote control by AT commands (GSM 07.07 and 07.05) baud rate from 300 to 115,200 bits/s from 300 up to 38400 bits/s with autobauding 9/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 1.3 Mechanical Design Overview Integra is encased as shown in the figure here-below. It includes a WISMO module, a 50-pin connector, a SIM holder and a RF connector. figure 1 : mechanical description 10/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 figure 2 : mechanical description II 4 screw holes allow the Integra to be fixed on the mother PCB. The Integra can be mounted indifferently on both sides (top or bottom). For further details see mechanical specifications in annex. 11/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Note: Interfaces The integrated modem has a sole 50-pin connector which gathers all the interface signals in order to facilitate its integration. It has an integrated SIM card holder as well as a standard RF connector type MMCX (Miniature Micro Connector) The concept of the integrated modem has been defined to integrate on a sole device:

only one standard easy to find connector (worldwide supplied) gathering the analog and digital interfaces one standard easy to find RF connector. See chapter RF connector page 34 one SIM card holder. See chapter SIM interface 12/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 2 Safety precautions 2.1 RF safety IMPORTANT FOR THE EFFICIENT AND SAFE OPERATION OF YOUR GSM INTEGRATED MODEM READ THIS INFORMATION BEFORE USE General 2.1.1 Your Integra modem is based on the GSM standard for cellular technology. The GSM standard is spread all over the world. It covers Europe, Asia and some parts of America and Africa. This is the most used telecommunication standard. Your modem is actually a low power radio transmitter and receiver. It sends out and receives radio frequency energy. When you use your Integra integrated modem, the cellular system which handles your calls controls both the radio frequency and the power level of your cellular modem. Exposure to RF energy 2.1.2 There has been some public concern about possible health effects of using GSM modems. Although research on health effects from RF energy has focused on the current RF technology for many years, scientists have begun research regarding newer radio technologies, such as GSM. After existing research had been reviewed, and after compliance to all applicable safety standards had been tested, it has been concluded that the product was fitted for use. If you are concerned about exposure to RF energy there are things you can do to minimize exposure. Obviously, limiting the duration of your calls will reduce your exposure to RF energy. In addition, you can reduce RF exposure by operating your cellular modem efficiently by following the below guidelines. Efficient modem operation 2.1.3 For your modem to operate at the lowest power level, consistent with satisfactory call quality :

If your modem has an extendible antenna, extend it fully. Some models allow you to place a call with the antenna retracted. However your modem operates more efficiently with the antenna fully extended. Do not hold the antenna when the modem is IN USE . Holding the antenna affects call quality and may cause the modem to operate at a higher power level than needed. Antenna care and replacement 2.1.4 Do not use the modem with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself. If so, use only a manufacturer-approved antenna. Otherwise, have your antenna repaired by a qualified technician. Use only the supplied or approved antenna. Unauthorized antennas, modifications or attachments could damage the modem and may contravene local RF emission regulations or invalidate type approval. 13/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 2.2 General safety Driving 2.2.1 Check the laws and the regulations regarding the use of cellular devices in the area where you have to drive as you always have to comply with them. When using your modem while driving, please :

give full attention to driving, pull off the road and park before making or answering a call if driving conditions so require. Electronic devices 2.2.2 Most electronic equipment, for example in hospitals and motor vehicles is shielded from RF energy. However RF energy may affect some improperly shielded electronic equipment. Vehicle electronic equipment 2.2.3 Check your vehicle manufacturer representative to determine if any on-board electronic equipment is adequately shielded from RF energy. Medical electronic equipment 2.2.4 Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc...) to determine if they are adequately shielded from external RF energy. Turn your modem OFF in health care facilities when any regulations posted in the area instruct you to do so. Hospitals or health care facilities may be using RF monitoring equipment. Aircraft 2.2.5 Turn your modem OFF before boarding any aircraft. Use it on the ground only with crew permission. Do not use it in the air. To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your modem while the aircraft is on the ground. To prevent interference with cellular systems, local RF regulations prohibit using your modem while airborne. Children 2.2.6 Do not allow children to play with your modem. It is not a toy. Children could hurt themselves or others

(by poking themselves or others in the eye with the antenna, for example). Children could damage the modem, or make calls that increase your modem bills. Blasting areas 2.2.7 To avoid interfering with blasting operations, turn your unit OFF when in a blasting area or in areas posted : turn off two-way radio . Construction crew often use remote control RF devices to set off explosives. 14/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Potentially explosive atmospheres 2.2.8 Turn your modem OFF when in any area with a potentially explosive atmosphere. It is rare, but your modem or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injuries or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fueling areas such as petrol stations ; below decks on boats ; fuel or chemical transfer or storage facilities ; and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Do not transport or store flammable gas, liquid, or explosives, in the compartment of your vehicle which contains your modem or accessories. Before using your modem in a vehicle powered by liquefied petroleum gas (such as propane or butane) ensure that the vehicle complies with the relevant fire and safety regulations of the country in which the vehicle is to be used. 2.3 Safety standards THIS INTEGRA COMPLIES WITH ALL APPLICABLE RF SAFETY STANDARDS. This cellular modem meets the standards and recommendations for the protection of public exposure to RF electromagnetic energy established by governmental bodies and other qualified organizations, such as the following :

Directives of the European Community, Directorate General V in Matters of Radio Frequency Electromagnetic Energy 3 Standard Compliance 3.1 GSM compliance Reference regulations: TBR 19, TBR 20, TBR 31, TBR 32 Table 1 : Wavecom acceptance test Tests Performance Test Cooking Test Stress Test Vibration Test Vibration Test Shock Test Applied Standard ETSI recommendation for GSM/DCS communication.

Therma shocks IEC 68-2-

14. Sinusoidal vibration 68-2-6. Random vibration IEC 68-

2-36. IEC 68-2-27. IEC Bump Test IEC 68-2-29. Acceptance Criteria Full conformity to parameters. the recommendation regarding the main RF The test continues even after the Cooking Test milestone has been reached Full conformity to the recommendation regarding the main parameters. No performance degradation or mechanical degradation is allowed after test. No performance degradation or mechanical degradation is allowed after test. No performance degradation or mechanical degradation is allowed after test. No performance degradation or mechanical degradation is allowed after test. The unit is tested at room temperature and must be fully operative for the main RF parameters. Humidity Test Corrosion test IEC 68-2-3. No visible degradation of the product, both visual and functionnal. 15/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra Warehouse Test Low temperance IEC 68-

2-1. Warehouse Test High temperature IEC 68-

2-2. MIL-STD-810D, method 510-3. radiation UV temperature HN60E03. IEC 68-2-32. and EDF IEC 1000-4-2. IEC 68-2-11 Flowing corrosion. IEC 68-2-60 EN 60 950 mixed gas Dust Test Light Test Fall Test Electro Static Discharge Test Salt Mist Test Atmosphere Test Marking Test March 2002/ version 1.6 Under normal condition (room temperature) after the test, the unit must behave in full conformity with the main RF parameters specification. Under normal condition (room temperature) after the test, the unit must behave in full conformity with the main RF parameters specification. No visible dust in the visible areas. No more than 50 dust particules in the cabinet of the product. The unit, tested at room temperature must be fully operative. Visual inspection on the discoloration and other degradation effects such as cracks in the material of the unit after the test. Only minor casing degradation is allowed, with a maximum dimension change of 1mm. The unit must remain fully operative and full specification for the main RF parameters. No performance degradation allowed after the test. After the test, visual inspection on the unit. After the test, visual inspection on the unit and inside. After the test, visual inspection on the unit. No degradation is allowed on the marking. 3.2 FTA Compliance The Integra has received a Full-Type Approval (according to normal MS requirements) in the configuration using the internal SIM interface. IMEI Number 3.2.1 GSM 900/1800:

TAC: 5 000 64 FAC: 11 Serial Numbers: 000000 to 999999 GSM 900/1900:

TAC: 500 100 FAC: 11 Serial Number: 000000 to 999999 GSM/GPRS 900/1800:

TAC: 500161 FAC: 11 Serial Numbers: 000000 to 999999 GSM/GPRS 900/1900:

TAC: 500167 FAC: 11 Serial Number: 000000 to 999999 16/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 CE Label 3.2.2 The Integra integrated modem is CE compliant which implies that the modem is in conformity with the European Community directives and it bears the CE label Carrying out tests:

Electro-magnetic field immunity EN 61000-4-3 ETS 300-3421 Radiated emission EN 55022 ETS 300-342 ESD immunity EN 61000-4-2 ETS 300-342-1 17/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 4 Hardware Interfaces This chapter describes the hardware interfaces:

interfaces on the 50-pin general purpose connector RF interface SIM interface 4.1 Interfaces on the 50-pin general purpose connector 4.1.1 The 50-pin connector description Table 2 : 50-pin connector description I/O Pin # Name GND 1 GND 2

+5V 3 4

+5V CT109/DCD O 5 GND 6 GPIO4 7 8 9 10 11 SPK2N CT125/RI SPK2P Flashing LED O O O I/O I/O 12 13 14 15 16 17 18 19 20 21 22 23 24 25 SPK1P O CT106/CTS O SPK1N ON/~OFF MIC2P AUXV0 MIC2N

~RST MIC1P GND MIC1N BOOT GND CT103/TX O I I I I I I I I I I 26 GPIO0 I/O Description GROUND GROUND I/O type Supply Supply CMOS/2X RS232-Data Carrier Detect CMOS/2X General Purpose I/O GROUND Comment High current High current High current High current High current Speaker2 negative output Analog CMOS/2X RS232-Ring Indicator Analog CMOS/2X Working mode indication Speaker 2 positive output Driven by module Analog 1X Analog Analog Analog Analog Analog Analog 2 positive ON = VCC(3) Led Speaker 1 positive output RS232 interface Clear To Send Speaker 1 negative output Power ON/OFF control Microphone input Auxiliary ADC input Microphone 2 negative input Reset active low Microphone 1 input Ground Microphone 1 negative input BOOT GROUND RS232 interface - Transmit Pull up to VCC(3) with 100K when not used Open Collector High current Open Collector positive CMOS/2X General Purpose I/O 18/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Pin # Name 27 I/O CT107/DSR O I/O type 1X 28 29 CT104/RX O CT108-2/DTR I 1X Description RS232 interface Data Set Ready RS232 interface Receive RS232 interface Data Terminal Ready 30 CT105/RTS I COL3 COL4 COL1 COL2 ROW4 COL0 ROW2 ROW3 ROW0 ROW1 GND(1) NC(2) SPI_EN SPI_IO SPI_CLK SIMCLK SIMRST SIMVCC I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O O O O O SIMPRES1 I 1X 1X 1X 1X 1X 1X 1X 1X 1X 1X 1X 1X 1X 2X 2X RS232 interface Request To Send Keypad column Keypad column Keypad column Keypad column Keypad row Keypad column Keypad row Keypad row Keypad row Keypad row GROUND(1) No Connected(2) SPI enable I2 C Data or SPI Data I2 C Clock or SPI Clock Clock for SIM Interface Reset for SIM interface SIM card supply SIM card detect 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Comment Pull up to VCC(3) with 100K when not used Pull up to VCC(3) with 100K when not used High current 3V mode 3V mode 3V mode 6mA max Connected to SIM connector pin 8. Pin 4 of SIM connector must be pulled down to GND with 1 K*

3V mode High current SIMDATA GND(1), GPO0(2)**

I/O 3X I/O for SIM interface See (1) and (2)

(1) for engineering sample

(2) for production unit.

(3) VCC = application digital power supply either 5V or 2.8V

*see SIM socket diagram 4.3 SIM interface

** GPO0 is a general purpose output for selection of external SIM 3V or 5V 19/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 3 : operating conditions Parameter I/O type Vinput low Vinput high Voutput low Voutput high CMOS CMOS 1X 2X 3X 1X 2X 3X Min

-0.5 V 2.1 V 2.6 V 2.6 V 2.6 V Max 0.8 V 3.0 V 0.2 V 0.2 V 0.2 V Condition IOL = -1 mA IOL = -2 mA IOL = -3 mA IOH = 1 mA IOH = 2 mA IOH = 3 mA 20/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 GND

+ 5 V CT109/DCD GPIO4 CT125/RI FLASHING LED CT106/CTS ON/~OFF AUXV0

~RST GND BOOT CT103/Tx CT107/DSR CT108-2/DTR COL3 COL1 ROW4 ROW2 ROW0 GND(1), NC(2) SPI IO SIMCLK SIMVCC SIMDATA 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 GND

+ 5 V GND SPK2N SPK2P SPK1P SPK1N MIC2P MIC2N MIC1P MIC1N GND GPIO0 CT104/Rx CT105/RTS COL4 COL2 COL0 ROW3 ROW1 SPI EN SPI CLK SIMRST SIMPRES1 GND(1), GPO0(2)

(1) for engineering sample

(2) for production unit figure 3 : 50-pin connector 21/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 50 2 49 1 figure 4 : pin numbering/bottom view Power supply 4.1.2 The main power supply is provided through a double connection. These connections are respectively the pin 3 and 4 for the +5V and the pins 1 and 2 for the ground (GND). The pins 6, 21, 24 and 40 are also ground connection in order to produce a proper ground plane. A 5V +/-5% - 1A power is strictly required to supply the modem. Otherwise, serious dysfunctions may appear. However, the modem does not have to constantly deliver 1A current at 5V on this power supply. This power supply is internally regulated to a nominal value VBATT. Table 4 : power supply pin description Pin number 1 2 3 4 6 21 24 41*

50*

*for engineering sample Name GND GND

+5 V

+5 V GND GND GND GND GND Description Ground Ground Ground Ground Ground Ground Ground Ground Ground Comment High Current High Current High Current High Current High Current High Current High Current High Current High Current 22/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 5 : Power consumption in EGSM only mode @ 25C

+5V

+5V

+5V

+5V

+5V Conditions During TX bursts @ 2W Average @ 2W Average @ 0.5W Average Idle mode Average Idle with power saving mechanism activated INOM 810 mA 310 mA 185 mA 22 mA 9.2 mA IMAX 1 A 370 mA 200 mA 25 mA 10.5 mA

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V Table 6 : Power consumption in GSM only 1800 and1900 mode @ 25C Conditions During TX bursts @ 1W Average @ 1W Average @ 0.25W Average Idle mode Average Idle with power saving mechanism activated INOM 635 mA 260 mA 150 mA 20 mA 9.2 mA IMAX 800 mA 280 mA 170 mA 22 mA 10.5 mA Table 7 : Power consumption in EGSM/GPRS cl2 mode @ 25C Conditions During TX bursts @ 2W Average @ 2W Average @ 0.5W Average in GPRS @ 2W Average Idle mode Average Idle with power saving mechanism activated INOM 810 mA 310 mA 185 mA 410 mA 22 mA 9.2 mA IMAX 1 A 370 mA 200 mA 490 mA 25 mA 10.5 mA 23/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 8 : Power consumption GSM/GPRS cl2 1800 or 1900 mode @

25C

+5V

+5V

+5V

+5V

+5V

+5V Conditions During TX bursts @ 1W Average @ 1W Average @ 0.25W Average in GPRS @ 1W Average Idle mode Average Idle with power saving mechanism activated INOM 635 mA 260 mA 150 mA 360 mA 20 mA 9.2 mA IMAX 800 mA 280 mA 170 mA 400 mA 22 mA 10.5 mA Serial link 4.1.3 A serial link interface is available complying with V24 protocol signalling but not with V28 (electrical interface) due to a 2.8 Volts interface. TX, RTS and DTR can be either 5V or 3V. The signals are Tx data (CT103/TX), Rx data (CT104/RX), Request To Send (CT105/RTS), Clear To Send (CT106/CTS), Data Terminal Ready (CT108-2/DTR) and Data Set Ready (CT107/DSR). The set of RS232 signals can be required for GSM DATA services application. The 2 additional signals are Data Carrier Detect (CT109/DCD) and Ring Indicator (CT125/RI). Table 7 : Serial Link pin description Signal Pin number I/O I/O type*

Description 25 28 30 13 27 29 5 9 21,24**

CT103 / TX CT104 / RX CT105 / RTS CT106 / CTS CT107 / DSR CT108-2 / DTR CT109 / DCD CT125 / RI CT102/GND

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description

** Any of the available GND pins can be used Transmit serial data Receive serial data Ready To Send Clear To Send Data Set Ready Data Terminal Ready Data Carrier Detect Ring Indicator Ground CMOS 1X CMOS 1X 1X CMOS CMOS / 2X CMOS / 2X I O I O O I O O 24/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Modem Level Shifter Terminal VCC GND VCC GND VCC 28 25 1 3 C1+

C1-

C2+

C2-

RI 24 T1IN DCD 23 RX 22 CTS 19 DSR 17 T2IN T3IN T4IN T5IN 16 R1OUTB DTR 21 TX 20 RTS 18 R2OUT R3OUT R4OUT VCC 13 ON 27 2 26 4 5 6 7 10 12 8 9 11 15 14 T1OUT T2OUT T3OUT T4OUT T5OUT R1IN R2IN R3IN ERROR OFF S_RI S_DCD S_RX S_CTS S_DSR S_DTR S_TX S_RTS VCC figure 5* : level shifter application diagram for serial link MAX 3238

* This application note is valid for VCC 3.0Volt (see MAX3238 specifications). Auto shut down mode is not used in this example. ON / ~OFF 4.1.4 This input is used to switch ON or OFF the Integra modem. A high level signal has to be provided on the ON/~OFF pin to switch on the modem. The level of the voltage of this signal has to be maintained to VCC during a minimum time of 1 second. When powered off, the shutdown current is roughly 60 A. 25/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 8 : ON / OFF pin description Signal Pin number I/O I/O type*

Description ON/OFF

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Module Power ON/OFF CMOS 15 I to Integra Power OFF procedure 4.1.4.1 In order to power OFF the Integra, switch it OFF both via software (AT+CPOF, See AT commands users guide for more details) and via hardware line. See the diagram below. ON/~OFF Serial link Integra Status ON OFF Serial Link from Integra About 500 ms OK response AT+CPOF figure 6 : power OFF procedure 1 ON/~OFF Serial link to Integra Serial link from Integra ON OFF Integra status AT+CPOF About 500 ms OK response About About 500 ms 500 ms figure 7 : power OFF procedure 2 26/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 BOOT 4.1.5 This input is used to switch the Integra into download mode (backup procedure). The internal boot procedure is started when this pin is low during the power ON of the module. In normal mode, this pin has to be left open. If used, this input has to be driven by an open collector or an open drain. See below an example of application diagram. See also the software upgrade procedure in General Guidelines chapter 8 BOOT : pin 23 Switch BOOT figure 8 : boot procedure If Switch Boot = 1, Boot pin 23 = 0, to download mode If Switch Boot = 0, Boot pin 23 = 1, to normal mode Table 9 : BOOT pin description Signal Pin number I/O I/O type*

Description BOOT

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description SW downloading CMOS 23 I 27/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Reset signal (~RST) 4.1.6 This signal is used to force a reset of the Integra. It has to be used by providing low level during approximately 2ms. This signal has to be considered as an emergency reset only. A reset procedure is already driven by an internal hardware during the power-up sequence. This signal can also be used to provide a reset to an external device. If no external reset is necessary this input can be left open. If used (emergency reset), it has to be driven by an open collector or an open drain. See below an example of application diagram. Reset : pin 19 Switch reset figure 9 : reset procedure If switch Reset = 1, Reset pin 19 = 0 If switch Reset = 0, Reset pin 19 = 1 Table 10 : reset signal pin description Signal Pin number I/O I/O type*

Description RST

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Module Reset I/O 19 Table 11 : reset signal electrical characteristics Parameter Input Impedance ( R ) Input Impedance ( C ) Min 4.7 Max 10 Unit k NF Table 12 : reset signal operating conditions Parameter Min

*VT-

*VT+

VOL VOH VT-, VT+ : Hysterisis Level 1.1V 1.7V 2.0 V Max 1.2 V 1.9 V 0.4 V Condition IOL = -50 A IOH = 50 A 28/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Flashing LED 4.1.7 The flashing LED signal is used to indicate the working mode of the Integra. Table 13 : the flashing LED pin description Signal Pin number Flashing LED 11 I/O I/O I/O type*

CMOS/2X Description Working mode indication LED

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description LED status OFF ON Table 14 : LED and Integra status Integra status Download mode or switched OFF Permanent Slow flash Quick flash Switched ON, not registered on the network Switched ON, registered on the network Switched ON, registered on the network, communication in progress General Purpose Input/Output 4.1.8 The Integra provides 2 General Purpose I/O. They are used to control any external device. Table 15 : General Purpose pin description Signal Pin number GPIO0 26 I/O I/O CMOS / 2X I/O type*

Description Default value GPIO4 7 I/O CMOS / 2X General Purpose I/O General Purpose I/O 0 0

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description All digital I/O comply with 3Volts CMOS. You can access (write or read) the GPIO value via AT+WIOW and AT+WIOR. See AT commands users guide for more details. Analog to Digital Converter 4.1.9 Analog to Digital converter (ADC) input is provided by the Integra. This converter is a 10 bits one, ranging from 0 to 2.5V. You can see the measurements via AT+ADC. See AT commands users guide for more details. 29/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 16 : A/D converter pin description Signal AUXV0 Pin number I/O I/O type*

Description 17 I Analog A/D converter

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description description Table 17 : A/D converter electrical characteristics Parameter Resolution Sampling rate Input signal range ADC Reference Accuracy Integral Accuracy Differential Accuracy Input Impedance ( R ) Input Impedance ( C ) Min 10 90.3 0 0.5

+/- 1

+/- 1 10 Max 2.5V 50 Unit bits Ksps V

LSB LSB M pF 30/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Audio Interface 4.1.10 Two different microphone inputs and two different speaker outputs are supported. The connection can be either differential or single-ended but using a differential connection in order to reject common mode noise and TDMA noise is recommended. 4.1.10.1 Microphone 2 Inputs The MIC2 inputs are differential ones. They already include the convenient biasing for an electret microphone (0,5 mA and 2 Volts). This electret microphone can be directly connected on these inputs. The impedance of the microphone 2 has to be around 2k. These inputs are the standard ones for a handset design while MIC1 inputs can be connected to an external headset or a handsfree kit. The gain of MIC2 inputs is internally adjusted. The gain can be tuned from 30dB to 51dB. The connection to the microphone is direct. The gain can be tuned using the AT+VGR command. See chapter Connector suppliers and peripheral devices. C1 = 22pF to 100pF 33 pF recommanded MIC2N MIC2P C1 figure 10 : microphone 2 input C1 has to be the nearest as possible to the microphone. Microphone manufacturers provide this capacitor directly soldered on the microphone. Table 18 : microphone 2 input pin description Signal MIC2P MIC2N Pin #

I/O I/O type*

Description 16 18 I I Analog Analog Microphone 2 positive input Microphone 2 negative input

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description 4.1.10.2 Microphone 1 Inputs The MIC1 inputs are differential and do not include internal bias. To use these inputs with an electret microphone, bias has to be generated outside the INTEGRA modem according to the characteristic of this electret microphone. These inputs are the standard ones used for an external headset or a handsfree kit. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as shielding in order to avoid any disturbance on the audio path. The gain of MIC1 inputs is internally adjusted. The gain can be tuned from 30dB to 51dB. The gain can be tuned using the AT+VGR command. Differential connection VCC analog power supply 2.8V R1 31/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential MIC1P R2 C2 C1 Integra March 2002/ version 1.6 figure 11 : microphone 1 input R1 = R4 = from 100 to 330 R2 = R3 =

usually between 1K and 3.3K as per the microphone characteristics C1 = 22pF to 100pF C2 = 47F R1 and R4 are used as a voltage supply filter with C2. C1 has to be the nearest possible to the microphone. Microphone manufacturers provide this capacitor directly soldered on the microphone. Table 19 : microphone 1 input pin description Signal Pin #

I/O I/O type*

Description MIC1P MIC1N Microphone 1 positive input Microphone 1 negative input

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Analog Analog 20 22 I I 32/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Speaker 2 Outputs 4.1.10.3 Speaker outputs SPK2 are push-pull amplifiers and can be loaded down to 50 Ohms and up to 1nF. These outputs are differential and the output power can be adjusted by step of 2dB. The output can be directly connected to a speaker. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as shielding in order to avoid any disturbance on the audio path. Differential Connection Single-ended Connection C1

figure 12 : speaker 2 output SPK2P SPK2N SPK2P C1 = from 100nF to 47F as per the speaker characteristics and the output power. Using a single-ended connection also includes losing half of the output power compared to a differential connection. Table 20 : speaker 2 output pin description Signal Pin #

I/O I/O type*

Description SPK2P SPK2N

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Speaker 2 positive output Speaker 2 negative output Analog Analog 10 8 O O 33/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Speaker 1 Outputs 4.1.10.4 Speaker outputs SPK1 are push-pull amplifiers and can be loaded down to 50 Ohms and up to 1nF. These outputs are differential and the output power can be adjusted by step of 2dB. The output can be directly connected to a speaker. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as a shielding in order to avoid any disturbance on the audio path. Differential Connection Single-ended Connection SPK1N SPK1P SPK1P C1

figure 13 : speaker 1 output C1 = from 100nF to 47F as per the speaker characteristics. Using a single-ended connection also includes losing half of the output power compared to a differential connection. Table 21 : speaker 1 output pin description Signal Pin #

I/O I/O type*

Description SPK1P SPK1N

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Speaker 1 positive output Speaker 1 negative output Analog Analog 12 14 O O 34/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 SIM interface 4.1.11 The external SIM interface is available through the 50-pin connector in order to use a stand-alone SIM card holder. This interface is 3V only on the engineering samples. 5V SIMs can be driven with production unit using an external level shifter. SIM line must not exceed 15 cm. see also General guidelines chapter 8 5 signals are available:

SIMVCC: SIM power supply. SIMRST: reset. SIMCLK: clock. SIMDATA: I/O port. SIMPRES1 SIM card detect. This signal is connected to the external SIM connector on pin 8. Pin 4 of SIM connector must be pulled down to GND with 1 K. This interface is fully compliant with GSM 11.11 recommendations concerning the SIM functionality. Transient Voltage Suppressor diodes are internally added on the signals connected to the SIM socket in order to prevent any Electro-Static Discharge. TVS diodes with low capacitance (less than 10pF) are connected on SIMCLK and SIMDATA to avoid any disturbance of the rising and falling edge. Table 22 : SIM interface pin description Signal Pin number I/O I/O type*

Description 45 46 49 47 48 50 SIMCLK SIMRST SIMDATA SIMVCC SIMPRES1 GPO0**

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description

** for production units SIM Clock 2X 2X SIM Reset CMOS / 3X SIM Data CMOS 2X SIM Power Supply SIM Card Detect SIM 3V or 5V O O I/O O I O See application schematics in annex for 3V/5V SIM management 35/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra Parameter SIMDATA VIH SIMDATA VIL SIMRST, SIMDATA SIMCLK VOH SIMRST, SIMDATA SIMCLK VOL SIMVCC Output Voltage SIMCLK Rise/Fall Time SIMRST, SIMDATA Rise/Fall Time SIMCLK Frequency March 2002/ version 1.6 Table 23 : SIM interface electrical characteristics Min Typ Max Unit Conditions IIH = 20A IIL = 1mA Source current =

20A 0.7xSIMVCC SIMVCC 0.1V Sink current =

- 200A ISIMVCC <= 6mA 2.70 Loaded with 30pF Loaded with 30pF Loaded with 30pF 2.80 V 0.3xSIMVCC V V 0.1 2.85 50 1 V V ns s 3.25 MHz Table 24 : SIM socket pin description Signal VCC RST CLK CC4 GND VPP I/O CC8 Pin number 1 2 3 4 5 6 7 8 Description SIMVCC SIMRST SIMCLK R10 to GROUND GROUND Not connected SIMDATA SIMPRES1 36/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 GND 1 K SIMVCC SIMRST SIMCLK SIMDATA SIMPRES1 1 2 3 7 8 VCC RST CLK CC4 GND VPP I / O CC8 Figure 14: SIM socket SPI bus 4.1.12 The SPI bus includes a CLK signal, an I/O signal and an EN signal complying with SPI bus standard. The maximum speed transfer is 3.25Mb/s. Table 25 : SPI Bus pin description Signal Pin number I/O I/O type*

Description SPI_CLK SPI_IO SPI_EN

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description SPI Serial Clock SPI Data SPI Enable 1X CMOS / 1X 1X O I/O O 44 43 42 Keypad interface 4.1.13 This interface provides 10 connections : 5 rows (R0 to R4) and 5 columns (C0 to C4). The scanning is a digital one, and the debouncing is done in the integrated modem. No discrete components like R,C (Resistor, Capacitor) are needed. It is possible to scan the column and rows using the: AT+ CMER. command. See AT command users guide for more details. 37/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Table 26 : keypad interface pin description Signal Pin number I/O I/O type*

Description ROW0 ROW1 ROW2 ROW3 ROW4 COL0 COL1 COL2 COL3 COL4

*See Table 3 operating conditions in subdivision 4.1.1The 50-pin connector description Row scan Row scan Row scan Row scan Row scan Column scan Column scan Column scan Column scan Column scan CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X CMOS / 1X I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O 39 40 37 38 35 36 33 34 31 32 38/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 4.2 RF Interface The impedance is 50 Ohms nominal. RF connector 4.2.1 The RF connector is MMCX (Miniature Micro Connector) standard type. An antenna can be directly connected through the matting connector or using a small adaptor. See also paragraph on GSM antenna. RF performances Intermodulation : > -43 dBm 4.2.2 RF performances are compliant with the ETSI recommendation 05.05 and 11.10. The main parameters are :

Receiver:

EGSM Sensitivity : < -104 dBm GSM 1800/GSM 1900 Sensitivity : < -102 dBm Selectivity @ 200 kHz : > +9 dBc Selectivity @ 400 kHz : > +41 dBc Dynamic range : 62 dB Co-channel rejection : + 9 dBc Transmitter :

Maximum output power (EGSM) : 33 dBm +/- 2 dB Maximum output power (DCS/PCS) : 30 dBm +/- 2 dB Minimum output power (EGSM): 5 dBm +/- 5 dB Minimum output power (DCS/PCS): 0 dBm +/- 5 dB H2 level : < -30 dBm H3 level : < -30 dBm Noise in 925 - 935 MHz : < -67 dBm Noise in 935 - 960 MHz : < -79 dBm Noise in 1805 - 1880 MHz : < -71 dBm Phase error at peak power : < 5 RMS Frequency error : +/- 0.1 ppm max 4.3 SIM interface The internal SIM interface of the Integra supports 3V SIMs only. The part number reference of the SIM card holder supplier is MOLEX 91228-0002 The part number reference of the SIM receptacle supplier is MOLEX 91236-0002 See also subdivision The SIM card holder. 39/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 5 Connector Supplier and Peripheral devices 5.1 Where to find the SMD connectors The Integra matting interface connector is made by SAMTEC France (http://www.samtec.com/). Many SAMTEC products are available via SAMTEC dealers throughout the world. The connectors data sheets are available in annex of this document. Figure 15: high and low profile CLP connectors Part number : FFSD-20-S-10-01-N Figure 16: flexible flat cable Part number : FLE 125 01LDVA Figure 17: flex cable connector 40/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 GSM Antenna 5.1.1 The integrated modem antenna connector is a MMCX connector. The MMCX connector incorporates a

'Snap On' latching action in order to make the connection easier with an excellent RF performance. An additional advantage is its small physical size which is 50% of the standard MCX connector. This type of connector is suitable for the standard ranges of flexible and semi-rigid cables. The characteristic impedance of the MMCX coaxial connector is 50 ohm. The antenna manufacturer must guarantee that the antenna will be working according to the following radio characteristics:

Table 27 : radio characteristics EGSM 900 925 to 960 MHz 880 to 915 MHz 2W at 12.5 % duty cycle GSM 1800 1805 to 1880 MHz 1710 to 1785 MHZ 1W at 12.5 % duty cycle 1W at 12.5 % duty cycle GSM 1900 1930 to 1990 MHz 1850 to 1910 MHz 50

< 2 0 dBi on azimuth plane The Integra requires an MMCX (Miniature Micro Connector) plug to connect an antenna Frequency RX Frequency TX RF power stand Impedance VSWR Typical gain radiated Figure 18: MMCX connector example (right angle) An antenna with matting connector can be ordered, for example, from :

IMS Connectors Systems GMBH Obere Hauptstrasse 30 D-79843 Lffingen Germany Tel : +49 76 54 90 10 Fax : +49 76 54 90 11 99 http://www.imscs.com/

or using a small MMCX / SMA adaptor can be ordered, for example, from :

Amphenol Socapex http://www.amphenol.com/

Order N : 908-31100 41/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 The SIM card holder 5.1.2 The SIM card holder used in the integrated modem is a MOLEX connector. Part number connector: 99228-0002 Part number holder : 91236-0002 For more information about this connector :

http://www.molex.com/

It is possible to use a stand-alone SIM card holder through the 50-pin connector (the length of the SIM line must not exceed 15 cm). 6 Climatic and mechanical environment Table 28 : climatic and mechanical environment WM2C-G900/G1800 TYPE OF TEST STANDARDS ENVIRONNEMENTAL CLASSES STORAGE Class 1.2 TRANSPORTATION OPERATING (PORT USE) Class 2.3 Class 7.3 Cold IEC 68-2.1

-25 C 72 h

-40 C 72 h Ab test

-20 C (GSM) 16 h

-10 C (DCS) 16 h Dry heat IEC 68-2.2

+70 C 72 h

+70 C 72 h

+55 C 16 h Change of temperature Bb test IEC 68-2.14 Na/Nb test Damp heat cyclic IEC 68-2.30 Db test

-40 / +30 C 5 cycles t1 = 3 h

-20 / +30 C (GSM) 3 cycles

-10 / +30 C (DCS) 3 cycles t1 = 3 h

+30 C 2 cycles 90% - 100% RH 90% - 100% RH 90% - 100% RH

+40 C 2 cycles

+40 C 2 cycles variant 1 variant 1 variant 1 Damp heat IEC 68-2.56

+30 C 4 days

+40 C 4 days

+40 C 4 days Cb test Sinusoidal vibration IEC 68-2.6 Fc test 5 - 62 Hz : 5 mm / s 62 - 200Hz : 2 m / s2 3 x 5 sweep cycles Random vibration wide band IEC 68-3.36 Fdb test 5 - 20 Hz : 0.96 m2 / s3 20 - 500Hz : - 3 dB / oct 10 -12 Hz : 0.96 m2 / s3 12 - 150Hz : - 3 dB / oct 3 x 10 min 3 x 30 min 42/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra 7 Demonstration board March 2002/ version 1.6 Download Flashing LED RS 232 serial link Test connector Power Supply 5V only/1 A Audio RJ 9 Handset and handsfree ON/OFF Reset Flex connector Keypad WMOi3 Integrated Modem SIM Card Holder Antenna Connector Figure 19: Integra demoboard description The Wavecom demonstration board (demoboard) is manufactured by Wavecom. It can be ordered from Wavecom or directly from your distributor. 43/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 8 General guidelines for the use of the Integra 8.1 Key information 8.1.1 Hardware and RF Ground plane: Wavecom recommends to have a common ground plane for analog, digital and RF grounds.

(mic + speaker) 1. Length of the SIM interface lines (15 cm maximum) Bias of the Microphone inputs must be properly adjusted when using audio connectors EMC protection on audio input/output (filters against 900 MHz) ESD protection on serial link, Possible spurious emission radiated by the application to the RF receiver in the receiver band The Antenna 8.1.2 The antenna sub-system and integration in the application is a major issue. It is a major issue in the choice of the antenna cable ( type, length, performances, thermal resistance, etc.) These elements could affect GSM performances such as sensitivity and emitted power. The antenna should be isolated as much as possible from the digital circuitry including the interface signals. It is recommended to shield the terminal. On terminals including the antenna, a poor shielding could dramatically affect the sensitivity of the terminal. Subsequently, the power emitted through the antenna could affect the application. Firmware upgrade 8.1.3 The Integra firmware is stored in flash memory and it can easily be upgraded. Two upgrade procedures are available:

one (nominal) procedure based on the Xmodem protocol (AT+WDWL command) one emergency mode (backup procedure) based on a Wavecom specific downloader Nominal upgrade procedure 8.1.3.1 The firmware file can be downloaded into the modem using the Xmodem protocol. To enter this mode, the AT+WDWL command (see description in the AT command manual) has to be sent to the Integra. The necessary serial signals to proceed with the Xmodem downloading are:

Rx, Tx, RTS, CTS, GND. 44/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 backup procedure 8.1.3.2 In case the nominal upgrade mode is not possible (due to critical corruption on the flash memory), a backup procedure is also available. It requires a WAVECOM specific software to download the firmware file into the modem. This tool has to run on a PC connected to the serial bus of the modem. As this procedure is very specific and needs Wavecom tools, this process has to be executed by your distributor. The necessary signals to proceed with the downloading are: Rx, Tx, RTS, CTS, GND. Prior to running the WAVECOM downloader, the modem has to be set in download mode. For this, the BOOT signal has to be set to low while powering ON (or reseting) the modem. The application must support serial speed changes, up to 115,200 bps and hardware flow control. 8.1.4 Getting started Minimum hardware interface to get started 8.1.4.1 As a minimum, it is necessary to connect the following signals to properly operate the Integra :

Table 29 : minimum signals to operate the Integra Pin number Name GND 1 GND 2 3

+5V

+5V 4 GND 6 CT106/CTS 13 15 ON/OFF GND 21 GND 24 CT103/TX 25 28 CT104/RX 30 CT105/RTS

* connected to +5V for example The serial link signals must be used through the implementation of the serial link level shifter. See figure 5 : level shifter application diagram for serial link Description GROUND GROUND Power supply Power supply GROUND Clear To Send Power On/OFF*

GROUND GROUND Transmit Receive Request To Send Terminal emulator setup 8.1.4.2 Here below is an example based on the WindowsTM Hyperterminal application (terminal emulator program). Setup:

START PROGRAMS ACCESSORIES HYPERTERMINAL , then Start the software HYPERTRM Give the name of your choice, click on the icone of your choice, then click OK, then choose:

Connect using : direct to COM1 Properties :

choose 9600 bps 8 bits data no parity 1 stop bit hardware flow control Click OK Once Hyperterminal is open and configured, it can be used to send AT commands to the Integra. Please see the Informative Example annex in the AT command users guide to test your Integra. 45/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 9 Reference documents Table 31 : GSM ETSI recommendations for Phase I and Phase II. Specification Reference GSM ph2 Radio DCS ph2 Radio GSM ph2 Link-Management GSM ph2 Link-Management GSM ph2 Layer 2 GSM ph2 Layer 3 DCS ph2 Layer 3 GSM/DCS Multiband GSM ph2 SIM GSM ph2 Teleservices GSM ph2 Miscellaneous DCS ph2 Miscellaneous You can find the documents on ETSI Contacts:

Title ETSI GSM 05.05 and GT 01 v4.2.1 ETSI GSM05.05 and GT01 v4.2.1 ETSI GSM 03.06, 04.08, 05.05, 05.08, 05.10, 07.01 and GT 01 v4.2.1 ETSI GSM 03.06, 04.08, 05.05, 05.08, 05.10, 07.01 and GT 01 v4.2.1 ETSI GSM 04.06 and GT 01 v4.2.1 ETSI GSM 04.08 and GT 01 v4.2.1 ETSI GSM 04.08 and GT 01 v4.2.1 ETSI GSM 02.07, 03.22, 04.08, 04.13, 05.05, 05.08 and GT 01 v4.2.1 ETSI GSM 11.11 and GT 01 v4.2.1 ETSI GSM 03.50 and GT 01 v4.2.1 ETSI GSM 02.07, 03.40, 03.41, 04.08, 04.10, 04.11, 06.10, 06.11, 06.1 06.31, 06.32, 07.01, 09.07 and GT 01 v4.2.1 ETSI GSM 02.07, 03.40, 03.41, 04.08, 04.10, 04.11, 06.10, 06.11, 06.1 06.31, 06.32, 07.01, 09.07 and GT 01 v4.2.1 ETSI Secretariat F-06921 Sophia Antipolis cedex, France e-mail: secretariat@etsi.fr http://www.etsi.org 46/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 10 Acronyms and Abbreviations ADC : Analog Digital Converter ASIC : Application Specific Integrated Circuit BCCH : Broadcast Control Channel CE : Communaut Europenne CLK : Clock CTS : Clear To send dB : decibel DCD : Data Carrier Detect DCE : Data Circuit Terminating Equipment DSR : Data Set Ready DTE : Data Terminal Equipment DTR : Data Terminated Ready EFR : Enhanced Full Rate E-GSM : Extended- GSM EMC : Electromagnetic Conformity EN : Enable ETSI :

FAC : Final Assembly Code FR : Full-Rate FTA : Full Type Approval GND : Ground GPIO : General Purpose Input Output GPRS : General Packet Radio Service GSM : Global System for Mobile Communication HR : Half-Rate IMEI : International Mobile Equipment Identity MO : Mobile Originated MT : Mobile Terminated OEM : Original Equipment Manufacturer PDA : Personal Digital Assistant PCB : Printed Circuit Board PRES : Presence RI : Ring Indicator RTS : Request To Send SIM : Subscriber Identity Module SMD : Surface Mounted Design SMS : Short Message Service TAC : Type Approval Code TDMA : Time Code Multiple Access TE : Terminal Equipment VSWR : Voltage Standing Wave Ratio WAP : Wireless application Protocol 47/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 11 Index 2 2X, 19, 20, 22, 23, 27, 34, 41 A Advice of Charge, 9 analog, 12, 52 Analog, 19, 20, 34, 35, 36, 38, 39, 40, 66 antenna, 9, 13, 14, 15, 46, 48, 49, 52 antenna cable, 52 asynchronous, 9 AT commands, 8, 9, 63 AT+ CMER, 44 AT+CPOF, 29 autobauding, 9 AUXV0, 20, 35 baud rate, 9 BOOT, 20, 31 bursts, 26 B C Call Barring, 9 Call Forwarding, 9 Call Hold, 9 Call Waiting, 9 Calling Line Identity, 9 Casing, 8 CE, 18, 56 Cell Broadcast, 9 Class 1, 8, 9 Class 4, 8 Closed User Group, 9 CMOS, 19, 20, 23, 27, 29, 31, 34, 41, 44, 45 column, 21, 44 connector, 7, 10, 12, 19, 22, 27, 29, 31, 32, 33, 34, 35, 36, 38, 39, 40, 41, 44, 45, 46, 47, 48, 49 converter, 34, 35 D data, 7, 8, 27, 64, 65 Data Carrier Detect, 19, 27 dB, 46, 56 DCS, 7, 16, 26, 46, 48, 55 digital, 12, 34, 44, 52, 66 Digital, 34, 56 dual-band, 7 E Easy remote control, 8 Echo, 63, 65 EFR, 8, 56 EMC protection, 52 Emergency calls, 8 ESD protection, 52 ETSI, 16, 46, 55 Explicit Call Transfer, 9 F fax, 7, 8, 9 Fixed Dialling Number, 9 Flash LED, 20 FR, 8, 56 G gain, 36, 37, 48, 66 general purpose, 19 General Purpose, 19, 20, 34 GND, 25 GND, 19, 20, 21, 22, 25, 27, 41, 43, 56 GPIO, 66 GPRS, 56 Ground plane, 52 GSM, 7, 8, 9, 13, 16, 27, 41, 48, 52, 55, 56 H handset, 36 hardware, 7, 8, 19, 29, 32, 53 HR, 8, 56 I I/O, 19, 20, 21, 22, 23, 27, 29, 31, 32, 33, 34, 35, 36, 38, 39, 40, 41, 43, 44, 45 Idle, 26 idle mode, 8 interface, 7, 8, 9, 12, 19, 20, 21, 22, 27, 41, 42, 44, 45, 46, 52 K M Keyboard, 21, 44 MIC1N, 20, 38 MIC1P, 20, 38 MIC2N, 20, 36 48/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 SIMPRES, 41 SIMRST, 22, 41, 42, 43 SIMVCC, 22, 41, 42, 43 SMS, 7, 8, 9, 56 socket, 22, 41 speaker, 36, 39, 40, 52 Speaker, 19, 20, 39, 40, 63 SPI, 21, 22, 44 SPK1N, 20, 40 SPK1P, 20, 40 Storage temperature, 8 Telephony, 8 terminal, 52 Tricodec, 8 UCS2, 9 USSD, 9 V.42bis, 9 VCC, 20, 21, 22, 43 voice, 7, 63, 66 Volume, 8 T U V W WAP, 56 Weight, 8 Integra, 1, 3, 6, 7, 10, 11, 13, 16, 17, 18, 28, 29, 31, 32, 34, 46, 52 X Xmodem, 9 MIC2P, 20, 36 microphone, 36, 37, 38, 63 Microphone, 63 Microphone, 20, 36, 37, 38, 52 MMCX (Miniature Micro Connector), 7, 12, 46, 48 MNP2, 9 MO, 9, 56 modem, 7, 8, 10, 12, 13, 14, 15, 16, 18, 25, 28, 37, 44, 46, 48, 49 module, 7, 10, 31 Mounting, 8 MT, 9, 56 Multiparty, 9 nominal value, 25 N O OFF, 15, 16, 20, 28, 29, 30 Ohms, 39, 40, 46 ON/~OFF, 20, 28 operating conditions, 23, 27, 29, 31, 32, 33, 34, 35, 36, 38, 39, 40, 41, 44, 45 Operating temperature range, 8 P PCB, 11 PCS, 7, 46, 48 Performance Test, 16 Phone Book, 64 phonebook, 64 point to point, 9 power, 8, 13, 25, 29, 30, 32, 39, 40, 41, 46, 48, 52 power supply, 25, 41 Power supply, 8, 25 R radio, 13, 16, 48, 65 Real Time Clock, 9 RF, 7, 10, 12, 13, 14, 15, 16, 17, 19, 46, 48, 52 Ring Indicator, 19, 27 RST, 20, 32, 33, 43 S serial link, 9, 27, 52 Signal, 27, 29, 31, 32, 33, 34, 35, 36, 38, 39, 40, 41, 43, 44, 45, 63 SIM, 7, 8, 9, 10, 12, 19, 22, 41, 42, 43, 46, 49, 52, 55, 56 SIM Toolkit, 9 SIMCLK, 22, 41, 42, 43 SIMDATA, 22, 41, 42, 43 49/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 50/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra Figures figure 1 : mechanical description........................................................................................................... 10 figure 2 : mechanical description II........................................................................................................ 11 figure 3 : 50-pin connector..................................................................................................................... 21 figure 4 : pin numbering/bottom view .................................................................................................... 22 figure 5* : level shifter application diagram for serial link ...................................................................... 25 figure 6 : power OFF procedure 1 ......................................................................................................... 26 figure 7 : power OFF procedure 2 ......................................................................................................... 26 figure 8 : boot procedure ....................................................................................................................... 27 figure 9 : reset procedure ...................................................................................................................... 28 figure 10 : microphone 2 input............................................................................................................... 31 figure 11 : microphone 1 input............................................................................................................... 32 figure 12 : speaker 2 output................................................................................................................... 33 figure 13 : speaker 1 output................................................................................................................... 34 Figure 14: SIM socket............................................................................................................................ 37 Figure 15: high and low profile CLP connectors.................................................................................... 40 Figure 16: flexible flat cable................................................................................................................... 40 Figure 17: flex cable connector ............................................................................................................. 40 Figure 18: MMCX connector example (right angle) .............................................................................. 41 Figure 19: Integra demoboard description ............................................................................................ 43 Tables Table 1 : Wavecom acceptance test ..................................................................................................... 15 Table 2 : 50-pin connector description .................................................................................................. 18 Table 3 : operating conditions ............................................................................................................... 20 Table 4 : power supply pin description.................................................................................................. 22 Table 5 : Power consumption in EGSM mode @ 25C......................................................................... 23 Table 6 : Power consumption in GSM 1800 and1900 mode @ 25C................................................... 23 Table 7 : Serial Link pin description ...................................................................................................... 24 Table 8 : ON / OFF pin description........................................................................................................ 26 Table 9 : BOOT pin description ............................................................................................................. 27 Table 10 : reset signal pin description................................................................................................... 28 Table 11 : reset signal electrical characteristics.................................................................................... 28 Table 12 : reset signal operating conditions.......................................................................................... 28 Table 13 : the flashing LED pin description........................................................................................... 29 Table 14 : LED and Integra status......................................................................................................... 29 Table 15 : General Purpose pin description.......................................................................................... 29 Table 16 : A/D converter pin description ............................................................................................... 30 Table 17 : A/D converter electrical characteristics ................................................................................ 30 Table 18 : microphone 2 input pin description....................................................................................... 31 Table 19 : microphone 1 input pin description....................................................................................... 32 Table 20 : speaker 2 output pin description .......................................................................................... 33 Table 21 : speaker 1 output pin description .......................................................................................... 34 Table 22 : SIM interface pin description................................................................................................ 35 Table 23 : SIM interface electrical characteristics................................................................................. 36 Table 24 : SIM socket pin description ................................................................................................... 36 Table 25 : SPI Bus pin description ........................................................................................................ 37 Table 26 : keypad interface pin description........................................................................................... 38 Table 27 : radio characteristics.............................................................................................................. 41 Table 28 : climatic and mechanical environment .................................................................................. 42 Table 29 : minimum signals to operate the Integra ............................................................................... 45 Table 31 : GSM ETSI recommendations for Phase I and Phase II....................................................... 46 Table 30 : AT command list................................................................................................................... 54 51/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 52/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 12 Annexes 12.1 Mechanical specifications 53/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 12.2 3V/5V SIM management 12.3 AT command list For comprehensive information about AT Commands, please read the AT Commands users guide Table 30 : AT command list General Commands

+CGMI

+CGMM

+CGMR

+CGSN

+CSCS

+CIMI

+CCID

+GCAP A/

+CPOF

+CFUN

+CPAS

+CMEE

+CKPD

+CCLK

+CALA Manufacturer Identification Request Model Identification Request Revision Identification Product Serial Number Select TE Character Set Request IMSI Card Identification Capabilities List Repeat Last Command Power Off Set Phone Functionality Phone Activity Status Report Mobile Equipment Errors Keypad Control Clock management Alarm management 54/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Call Control Commands D H A

+CEER

+VTD, +VTS ATDL AT%Dn ATSO

+CICB

+VGR, +VGT

+CMUT

+SPEAKER

+ECHO

+SIDET

+VIP

+CSNS Network Service Commands

+CSQ

+COPS

+CREG

+WOPN

+CPOL Security Commands

+CPIN

+CPIN2

+CPINC

+CLCK

+CPWD Phone Book Commands

+CPBS

+CPBR

+CPBF

+CPBW

+CPBP

+CPBN

+CNUM

+WAIP Dial command Hang-up Command Answer a Call Extended Error Report DTMF Signals Redial Last Telephone Number Automatic Dialing (or SMS send) with DTR Automatic Answer Incoming Call Bearer Gain Control Microphone Mute Control Speaker and Microphone Selection Echo Cancellation Side Tone Modification Initialize Voice Parameters Single Numbering Scheme Signal Quality Operator Selection Network Registration Read Operator Name Preferred Operator List Enter PIN Enter PIN2 PIN Remaining Attempt Number Facility Lock Change Password Select Phone Book Memory Storage Read Phone Book Entries Find Phone Book Entries White Phone Book Entry Phone Book Phone Search Move Action in Phone Book Subscriber Number Avoid Phone Book Init 55/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Select Message Service New Message Acknowledgement Preferred Message Storage Preferred Message Format Save Settings Restore Settings Show Text Mode parameters New Message Indication Read Message List Message Send Message Write Message to Memory Send Message from Storage Set Text Mode Parameters Delete Message Service Center Address Select Cell Broadcast Message Types Cell Broadcast Message Identifiers Message Status Modification Message Overwriting Short Message Commands

+CSMS

+CNMA

+CPMS

+CMGF

+CSAS

+CRES

+CSDH

+CNMI

+CMGR

+CMGL

+CMGS

+CMGW

+CMSS

+CSMP

+CMGD

+CSCA

+CSCB

+WCBM

+WMSC

+WMGO Supplementary Services Commands Call Forwarding

+CCFC

+CLCK Call Barring Modify SS Password

+CPWD Call Waiting

+CCWA Calling Line Identification Restriction

+CLIR

+CLIP Calling Line Identification Presentation Connected Line Identification Presentation

+COLP Advice Of Charge

+CAOC AccumulatedCcall Meter

+CACM

+CAMM Accumulated Call Meter Maximum Price Per Unit and Currency Table

+CPUC Call Related Supplementary Services

+CHLD List Current Calls

+CLCC

+CSSN Supplementary Service Notifications Unstructured Supplementary Service Data

+CUSD

+CCUG Closed User Group Data Commands

+CBST

+FCLASS

+CR

+CRC

+ILRR

+CRLP

+DOPT

%C

+DS

+DR

\N Bearer Type Selection Select Mode Service Reporting Control Cellular Result Codes DTE-DCE Local Rate Reporting Radio Link Protocol Parameters Others Radio Link Parameters Select Data Compression V42 bis Data Compression V42 bis Data Compression Report Select Data Error Correcting Mode 56/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Fax Commands

+FTM

+FRM

+FTH

+FRH

+FTS

+FRS Fax Class 2 Commands

+FDT

+FDR

+FET

+FPTS

+FK

+FBOR

+FBUF

+FCQ

+FCR

+FDIS

+FDCC

+FLID

+FPHCTO V24-V25 Commands

+IPR

+ICF

+IFC

&C

&D

&S O Q V Z

&W

&T E

&F

&V I SIM Toolkit Commands

+STSF

+STIN

+STGI

+STCR

+STGR Transmit Speed Receive Speed HDLC Transmit Speed HDLC Receive Speed Stop Transmission and Wait Receive Silence Transmit Data Receice Data Transmit Page Punctuation Page Transfer Status Parameters Terminate Session Page Transfer Bit Order Buffer Size Report Copy Quality Checking Capability to Receive Current Sessions Parameters DCE Capabilities Parameters Local ID String Page Transfer Timeout Parameter Fixed DTE Rate DTE-DCE Character Framing DTE-DCE Local Flow Control Set DCD Signal Set DTR Signal Set DSR Signal Back to Online Mode Result Code Suppression DCE Response Format Default Configuration Save Configuration Auto-Tests Echo Restore Factory Settings Display Configuration Request Identification Information SIM Toolkit Set Facilities SIM Toolkit Indication SIM Toolkit Get Information SIM Toolkit Control Response SIM Toolkit Give Response 57/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 Specific AT Commands

+CCED

+CCED

+WIND

+ADC

+CMER

+WLPR

+WLPW

+WIOR

+WIOW

+WAC

+WTONE

+WDTMF

+WDWL

+WVR

+WDR

+WHWV

+WDOP

+WSVG

+WSTR

+WSCAN

+WRIM

+W32K Cell Environment Description Automatic RxLev Indication General Indications Analog Digital Converters Measurements Mobile Equipment Event Reporting Read Language Preference Write Language Preference Read GPIO Value Write GPIO Value Abort Command Play Tone Play DTMF Tone Wavecom Downloading Wavecom Voice Rate Data Rate Hardware Version Date Of Production Wavecom Select Voice Gain Wavecom Status Request Wavecom Scan Ring Indicator Mode Power saving mode 58/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential Integra March 2002/ version 1.6 13 RF exposure instructions Pursuant to 47 CFR 24.52 of the FCC Rules and Regulations, personnal communications services (PCS) equipment is subject to the radiofrequency radiation exposure requirements specified in 1.1307(b), 2.1091 and 2.1093 as approporiate. The Wavecom Modem is a GSM (PCS 1900) terminal which operates in the US licensed PCS frequency spectrum. The device transmits over the 1850-1910 MHz band and receives over the 1930-1990 MHz Band. Wavecom, Inc. certifies that it has determined that the Modem complies with the RF hazard requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E of the FCC Rules and Regulations. This determination is dependent upon installation, operation and use of the equipment in accordance with all instructions provided. The Modem is designed for and intended to be used in fixed and mobile applications.

"Fixed" means that the device is physically secured at one location and is not able to be easily moved to another location. "Mobile" means that the device is designed to be used in other than fixed locations and generally in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter's antenna and the body of the user or nearby persons. The Modem is not designed for or intended to be used in portable applications

(within 20 cm of the body of the user) and such uses are strictly prohibited. To ensure that the unit complies with current FCC regulations limiting both maximum RF output power and human exposure to radiofrequency radiation, a separation distance of at least 20 cm must be maintained between the unit's antenna and the body of the user and any nearby persons at all times and in all applications and uses. Additionally, in mobile applications, maximum antenna gain must not exceed 3 dBi (to comply with Section 24.232(b) and is limited to7 dBi for fixed applications. Finally, the tune-up procedure for the O9EM2113 ensures that the maximum RF output power of the device does not exceed 30.0 dBm within the variations that can be expected due to quantity production and testing on a statistical basis. 59/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential March 2002/ version 1.6 Integra 14 Instructions to OEM Wavecom Users manual includes specific warnings and cautions in order to ensure that OEMs are aware of their responsibilities, with regards to RF exposure compliance, for products into which the modem is integrated. With this guidance, the OEM will be able to incorporate into their documentation the necessary operating conditions and warnings. OEMs need to provide a manual with the final product that clearly states the operating requirements and conditions and that these must be observed to ensure compliance with current FCC RF exposure requirements / MPE limits (refer to chapter 13. RF exposure instructions ). This will enable the OEM to generate (and provide the end-user with) the appropriate operating instructions, warnings and cautions, and/or markings for their product. 60/60 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable. confidential