INGICS TECHNOLOGY Guide Ver.0c iBS05 User Guide Introduction The document is a guide for iBS05/iBS05G/iBS05H/iBS05T. To quickly verify it, please download INGICS iBS01 Tag Utility APP from below link(Android only):
https://play.google.com/store/apps/details?id=com.ingics.tag.igstagcong Overview Operation Basically, iBS05 will always transmit BLE payload in the congured time interval(by default, iBS05/05G is 5s and iBS05H/05T is 30s) in the background after power on. The transmitted BLE payload/message is then received and uploaded to the internet/cloud server by the beacon gateway, such as iGS01S or iGS03W/M/E. Besides background transmission, button or sensor status change will also trigger an immediate BLE transmission for monitoring the sensor in real time. Power on iBS05 is in standby mode at shipping. You can power on it by pressing the front button. The LED will ash Red to indicate it is powered on. After power on, the button becomes the alarm button. Power off When necessary, users can power off iBS05 by applying a pencil with a blunt tip to the rubber button on the bottom side. The LED will ash Orange to indicate it is powered off and entering the standby mode. INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 1 INGICS TECHNOLOGY Alarm Button After power on, the front button acts as an alarm button. As pressing the button, the LED will light up green and trigger an immediate BLE transmission with the button activation event. As the back end server received this status change, it can be used as a warning or alarming. LED Power on( Start of Cong mode) Red blinking End of Cong mode Green blinking Alarm Button Green on when pressed Battery inserted/Power off Orange blinking Working Mode Hall Sensor (iBS05H) Inside iBS05H, there is a hall sensor that can be used to detect if a magnet is in range or not. Depending on the strength of the magnet, the active range is around 0.5cm~1.5cm. The sensor position is marked on the enclosure. A typical usage is to put an iBS05 and magnet on the door(or window) and door frame. When they are close to the active range, iBS05 will trigger an immediate BLE transmission. On the other hand, when they are far away from a close state, it will also trigger an immediate BLE transmission. Accelerometer (iBS05G) The accelerometer will be active when its status changes. It includes from motion to still or from still to motion. An immediate BLE transmission with status change will be triggered as active. Temperature Sensor (iBS05T) iBS05T is always monitoring the environment temperature and INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 2 INGICS TECHNOLOGY transmitting the temperature value in the congured time interval . Verifying 1. Power on iBS05 2. Open iBS01 Tag Utility APP and Press START SCAN. 3. Wait for a while, you should see the BLE payload of iBS05 received by the APP. Below is an explanation of the payload shown in the APP. Battery Level iBS05 uses a CR2032 coin battery as the power source. It consumes only a little power and keeps working for a long time. Below is a suggestion for translating the battery voltage to the remaining capacity at room temperature. Capacity High Middle Low Voltage
>2.9V
>2.8V
>2.65V Change battery
<=2.65V Remember, a proper ltering on the voltage is necessary. When iBS05 works in a low temperature environment, the battery voltage will be lower. For example, in -20 C, the voltage should be adjusted 0.1V~0.2V lower. Change Battery 1. Remove the 4 screws on the backside and open the bottom cover. 2. It is very important that without enclosure protection, the internal of iBS05 is sensitive to electrostatics. Before opening the bottom cover, please make sure the proper procedure is executed to avoid any electrostatic damage to iBS05. 3. Change a new battery 4. Before closing the bottom cover, please make sure the O-ring is in the proper position to keep iBS05 waterproof. 5. Fix the screws. INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 3 INGICS TECHNOLOGY Conguration When powered on, iBS05 will be in conguration mode for 20 sec. Users can use iBS01 Tag Utility to scan and connect iBS05 to congure the transmit power and ADV(advertising) interval. Steps 1. Power on iBS05
(if iBS05 is already powered on, please power off it rst then power on again) 2. Press the CONFIG icon on the up-right corner of the utility within 20 secs. Select iBS05 for conguration. 3. In the SETTING page, you can congure TX power and ADV interval. After conguring, ress SAVE and DISCONNECT for the parameters to take effect. Parameters In iBS05, there are two parameters that can be congured. a. TX power: +4 dBm ~ -20dBm. b. ADV Interval: From 100 ms~60 min. Waste Electrical and Electronic Equipment Recycling Our product is compliant with the WEEE directive for re-use/recovery/recycling. This cross-out wheeled-bin symbol is a reminder that this product should not be treated as household waste. Instead hand it over to the appropriate collection point for the recycling of electrical and electronic equipment in accordance with local environmental regulations for waste disposal. Since our product is not sold directly to the end user and generally it is a part of our customers solution, our customer is recognized as a professional seller. Our customer has the responsibility to comply with the requirement of the directive too. To help our customers, when necessary, we will provide a WEEE compliant assessment report for registering and communicating with the local authorities and recycling agency. Certication Japan MIC Regulatory FCC Regulatory 2AH2IIBS05 NCC Regulatory INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 4 INGICS TECHNOLOGY Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0.5 cm between the radiator and your body. Cet quipement est conforme aux CNR-102 d'Industrie Canada. Cet quipement doit treinstall et utilis avec une distance minimale de 0.5 centimtres entre le radiateur et votrecorps. Cet metteur ne doit pas tre co-localises ou oprant en conjonction avec autreantenne ou metteur. Les antennes utilises pour cet metteur doivent tre installs etfournir une distance de sparation d'au moins 0.5 centimtre de toute personne et doit pas tre co-situe ni fonctionner en conjonction avec une autre antenne ou metteur. NCC INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 5 INGICS TECHNOLOGY Revision History DATE REVISION CHANGES May 30, 2021 June 2, 2021 Aug 2, 2021 0a 0b 0c Initial release Add Waste Electrical and Electronic Equipment Recycling section for appropriate recycling the equipment Fix typo, modify LED section, and add Working mode section INGICS TECHNOLOGY CO., LTD. SUPPORT@INGICS.COM WWW.INGICS.COM 6