FCC ID: YCT-ISATPHONE2W Satellite phone with Bluetooth and GPS for Inmarsat GMR2+ satellite network

inmarsat.com/isatphone Signal strength Product name Network Local time Battery Alarm active New voicemail Unread message Active profile Status bar Information shortcut Left selection label Right selection label Programmable assistance button Ear piece Ambient light sensor LED tracking indicator LED status indicator Handsfree rest Tracking button Volume up key Volume down key Screen Right selection key Navigation keys Left selection key Call button Centre selection key End button Handsfree rest Keypad Microphone Micro USB port USB/audio protective cover 2.5mm audio connector Strap attachment point LED status indicators Insert the SIM card Slide the catch down on the SIM holder If the battery is in place, lift it out. and flip it outwards. Make sure the angled corner of your SIM card is on your left and slide it into the holder. Flip the holder back into place and slide the catch back up. Insert the battery. Charge the battery Connect the charger to a power source and the micro USB connector to the port at the base of the phone. Switch on Hold down the red key until the screen lights up. The first time you use your phone, use the navigation keys to select your language and set the time zone. To switch off, hold down the red key shuts down. until the screen Connect to the satellite Stand outside in a place where there are no obstacles between you and the sky. Fully deploy the handset antenna and point it upwards. To register to the Inmarsat network, your handset must acquire a GPS fix and simultaneously find the Inmarsat network. This happens automatically (see User Guide). When the handset is registered to the network, the name Inmarsat is displayed beside the signal strength indicator. To send and receive calls, at least two indicator bars must be filled. If signal strength is too low, on-screen instructions will help you to improve it (see User Guide). Note: Before you make a call, your phone needs a GPS fix so it can be located by the satellite. This happens automatically, but if a new GPS fix is needed, the icon will be displayed. Place the phone in the open with a clear view of the sky until the icon disappears. Make a call Enter the full international number by dialling +, country code, area code (without the leading 0), telephone number and press the green key e.g. +44 1621 123456 the red key

. To end a call, press

. Answer a call When your phone rings, press the green key Remember, to receive a call, you must be connected to the satellite with the phone antenna pointing upwards. Listen to voicemail Hold down the be connected to your voicemail. Alternatively, call +870 772 001 899 and press the green key key and you will automatically

. Incoming call alerts The handset has the capability to alert you to incoming calls and text messages when the antenna is stowed or the satellite signal reception is limited. Whenever you switch the handset on and deploy the antenna, the handset attempts to register to the network (see Connect to the satellite). If successful, the screen displays Ready for service and the two status LEDs change to green. After successful registration, you can stow the antenna. The status LEDs will change to amber to show that the handset is monitoring the network for incoming call alerts. Further information Please refer to the USB drive provided, which contains a full User Guide and applications for Contact Synchronisation, Firmware Upgrades and USB Drivers. Also available at inmarsat.com/isatphone Your phone number:

Your Service Providers number:

While the information in this document has been prepared in good faith, no representation, warranty, assurance or undertaking (express or implied) is or will be made, nor will responsibility or liability (howsoever arising) be accepted by the Inmarsat group or any of its officers, employees or agents in relation to the adequacy, accuracy, completeness, reasonableness or fitness for purpose of the information in this document. All and any such responsibility and liability is expressly disclaimed and excluded to the maximum extent permitted by applicable law. INMARSAT is a trademark owned by the International Mobile Satellite Organisation licensed to Inmarsat Global Limited. All other Inmarsat trademarks in this document, including the Inmarsat LOGO, are owned by Inmarsat Global Limited. In the event of any conflict between the words of the disclaimer and the English version from which it is translated, the English version shall prevail. Inmarsat Global Limited 2018. All rights reserved. IsatPhone 2 Quick Start Guide (Model 2.1) May 2018.

Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 1 inmarsat.com/isatphone Congratulations on buying your IsatPhone 2W. The satellite phone that delivers:

Dependable connectivity High quality voice Rugged design Assistance button, call alerts and tracking Extended battery capacity From the worlds leading provider of mobile satellite communications Please follow this user guide for further information on how to set up, connect, personalise and use your phone safely. Further information is available at inmarsat.com/isatphone. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Exposure to radio frequency energy frequency bands. IsatPhone 2W is a radio transmitter and receiver. When the phone or Bluetooth handsfree is turned on, it emits low levels of radio frequency energy. The phone is designed and manufactured not to exceed the safety limits for exposure to radio frequencies (RF) as recommended by the ICNIRP (International Commission on Non-Ionising Radiation Protection) and as adopted within mandatory standards of the European Commission and the United States of America. Specific Absorption Rate (SAR) is used to measure radio frequency energy absorbed by the body when using a mobile phone. IsatPhone 2W is compliant with the EC standards for exposure specified in EN 50360:2001 in accordance of EN 62209-1:2006. For use of the phone at the ear, these standards set a SAR limit of 2.0 W/kg averaged over a 10g volume. IsatPhone 2W is also compliant with the Federal Communications Commission (FCC) standards and test procedures as reflected in the requirements of 47 CFR 2.1093 in accordance of KDB 447498 D01 v06 and ISED RSS-102 in accordance of Health Canada Safety Code 6. For use of the phone at the ear, these standards set a SAR limit of 1.6 W/kg averaged over a 1g volume. Tests for SAR are conducted in accordance with international guidelines for testing using standard operating positions as per the procedures for the applicable standards, with the device transmitting at the highest certified power levels in all operational Note: Note: The SAR requirements for IsatPhone 2W are met for radiating operation whilst handheld at the ear. No measures have been taken for SAR compliance when radiating in a body-mounted position. Hence, radiating operation of the IsatPhone 2W is not recommended when in a body-mounted position. It should be noted that the IsatPhone 2W is not capable of radiating when the antenna is in the stowed position. Hence, when operating in incoming call alerting mode

(see page 20) with the antenna stowed, (either with or without the handset in the holster), the handset cannot radiate and may be body-mounted without posing a safety/health risk. Pacemakers Wireless phones may adversely affect the operation of some implanted cardiac pacemakers and other medically implanted equipment. Pacemaker patients should be aware that the use of an IsatPhone 2W in close proximity to a pacemaker might cause the device to malfunction. If a minimum distance of 15cm is kept between an IsatPhone 2W and a pacemaker, the risk of interference is limited. If you have any reason to suspect interference is occurring, immediately switch off your IsatPhone 2W. Contact your cardiologist for more information. 3 Safety 1 2 3 SAFETY Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Hearing aids Battery safety Although most modern hearing aids are immune to radio frequency interference from satellite terminals, some wireless devices may interfere with some hearing aids. In the event of such interference from the use of the IsatPhone 2W, maintain additional separation between you and your IsatPhone 2W and/or consult with your doctor or audiologist. Other medical devices Although most modern electronic medical equipment in hospitals and other clinical environments is shielded from RF energy, there is still a risk that a wireless device could cause interference. As such, never use your IsatPhone 2W near electronic medical equipment without first requesting permission. Blasting areas and potentially explosive environments As with any wireless phone, do not use your IsatPhone 2W where blasting work is in progress. Observe all restrictions and follow any regulations or rules. Do not use your IsatPhone 2W in areas with a potentially explosive atmosphere. Note that such areas are often, but not always, clearly marked. Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone. Use of batteries that are not Inmarsat-supplied or approved may pose increased safety risks. Do not dispose of batteries in a fire, as they may explode. See Care and maintenance on page 59, and for guidance on the disposal of batteries and electronic equipment, see page 63. Batteries may burn or explode if damaged. Do not dismantle, open, bend or cut cells or batteries. Do not attempt to modify or remanufacture the battery. Do not immerse or expose the battery to water or other liquids. In the event of a battery leak, avoid contact of contents with skin or eyes. If this does happen, flush the affected areas with water and seek medical help as appropriate. Children Keep out of the reach of children. Do not allow children to play with your phone or accessories. They could hurt themselves or others. Products may contain small parts that could become detached and create a choking hazard. 4 Safety 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Driving Loudness warning Only use IsatPhone 2W in a vehicle using an Inmarsat-

approved vehicular docking unit. Check with the vehicle manufacturer to be sure that your phone or Bluetooth will not affect the electronic systems in the vehicle. Full attention should be given to driving at all times and local laws and regulations restricting the use of electronic and wireless devices while driving must be observed. Avoid volume levels that may be harmful to your hearing. Pinch hazard Take care when opening and closing the antenna of your phone, as it may be possible to trap a fingertip. Land use only The IsatPhone 2W is approved for land use only. 5 Safety 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 6 Your IsatPhone Status icons Programmable assistance button Ear piece Ambient light sensor LED tracking indicator LED status indicator Handsfree rest Tracking button Volume up key Volume down key Screen Right selection key Navigation keys Left selection key Call button Centre selection key End button Handsfree rest Keypad Microphone Micro USB port USB/audio protective cover 2.5mm audio connector Strap attachment point LED status indicators Keypad locked GPS fix required Alarm set USB connection Call divert on Conference call activated Unread message Closed user group number Message sent New voicemail Microphone muted Missed call Loud profile active Loudspeaker activated Vibrate profile active Silent profile active Phone memory full Message memory full Bluetooth is paired SIM card memory full Bluetooth headset connected to your phone Wired handsfree headset connected Bluetooth on Assistance button activated QUICK REFERENCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Menu MESSAGING CONTACTS CALL LOG Missed calls Received calls Dialled calls Call duration Phonebook SIM contacts FND list My phone number Service provider Emergency numbers Voicemail number Groups LOCATION SERVICES ALARM Assistance button Tracking Send GPS Personal alert Once alarm Recurrent alarm GPS POSITION NETWORK GPS location Date and time Docking mode About Reset settings Satellite search Advanced options Network operator New message Inbox Outbox Drafts Sent Saved Templates SIM messages PROFILES General Silent Loud Vibrate only SETTINGS Call settings Security Language Display Prepay Bluetooth 7 User Guide instructions commence from the main screen. The red key will take you to the main screen. Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 8 Coverage map I-4 Americas Alphasat I-4 Asia-Pacific IsatPhone 2W operates globally over the Inmarsat-4 satellites and Alphasat. This map is illustrative of IsatPhone 2W coverage. It does not provide a guarantee of the extent of service availability. From November 2013, Alphasat coverage prioritises the region north of 44S, and service may degrade south of this latitude. This coverage map applies to both IsatPhone Pro and IsatPhone 2W. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 9 Package contents Your IsatPhone 2W box contains:

Phone Battery USB drive Quick Start Guide Warranty Mains charger and four universal plug adaptors Car charger Micro USB cable Wired handsfree headset Wrist strap Holster The USB drive can be accessed by a PC running Windows 7, 8, Vista or XP and contains the following documents:

Quick Start Guide User Guide Warranty The USB drive also contains the following applications and related How to guides:

USB Drivers: for charging your phone via a PC, setting up a software modem and for running Contact Synchronisation and Firmware Upgrade tools Contact Synchronisation Tool: for synchronising your phone with Microsoft Outlook and Microsoft Outlook Express contacts Firmware Upgrade Tool: for undertaking future upgrades The above documents and applications are available in English, Spanish, French, Japanese, Portuguese, Russian, Chinese and Arabic. They can also be downloaded from inmarsat.com/isatphone Setting up your IsatPhone Subscriptions and SIM cards To use your phone, you will need a SIM card and a subscription. The services available to you may depend on your choice of subscription. Contact your service provider for details. Setting up your IsatPhone 1 2 3 GETTING STARTED Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 10 Inserting and removing the battery Your phone is supplied with a rechargeable battery, which may not be fully charged when you take it out of the box. Always switch the device off and disconnect the charger before removing the battery. See Care and maintenance on page 59 for more information. Inserting the SIM card Your service provider may have inserted your SIM for you. If not, your phone will prompt you to Insert SIM and offer only a limited service until you do so. 1 Remove the battery by pressing the catch and lifting the battery up and out of the phone 2 Insert the battery by pressing the battery forward and down. It will click into place 1 If the battery is in place, lift it out 2 Slide the catch down on the SIM holder and flip it outwards 3 Make sure the angled corner of your SIM card is on your left and slide it into the holder 4 Flip the holder back into place and slide the catch back up 5 Insert the battery Setting up your IsatPhone 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 11 Charging the phone battery Your phone is powered by a rechargeable lithium-ion battery. To maximise its life and its charging capacity, the first time you charge the battery, charge it overnight. Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone. Do not leave the battery charging for extended periods of time. The battery can be charged by:

Using the AC charger (connecting to a wall socket) Using the micro USB cable (connecting to a PC) Using the car charger (connecting to a vehicle cigarette lighter/power outlet) Using the docking station You also have the option of using a solar charger. Contact your service provider for details. Connect the charger to a power source and the micro USB connector to the port at the base of the phone, under the USB/audio protective cover. When the battery needs charging, the low battery alert sounds and a Battery low message is displayed. The phone will automatically switch off shortly afterwards. You might be able to switch the phone on again, but you cannot make or receive any calls until the battery has been recharged or replaced. Use the Docking Mode option, on the Settings menu, to control battery recharging. The default setting is Off (full charge) this will continually charge your battery to 100% until your phone is removed from the charger or docking station. Select On (limited charge) to select a level at which recharging will be triggered. The Frequent docking option will start charging your battery when the charge drops to 80%

The Permanent docking option will start charging your battery when the charge drops to 20%

Note: If your phone is connected to a charger or docking station for long periods of time, you can use the docking mode settings to ensure that your phone only charges when necessary. This will prolong your battery life and conserve power. Setting up your IsatPhone 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 12 Attaching the wrist strap Your phone is supplied with a wrist strap. To connect the strap, remove the battery cover. Thread the small loop through the entry point at the base of the phone. Loop it over the anchor point to secure it and replace the battery cover. Switching your phone on and off To switch on, hold down the red key for a few seconds until the screen lights up. The Inmarsat logo will appear followed by the main screen. To switch off, press and hold the red key for a few seconds. Note: If you see the message Insert SIM, you must insert a SIM card to use your phone. You will also be prompted to enter the PIN code if one is set. The default setting for the PIN code is off. See Setting up SIM PIN code on page 55 for more information. Until a SIM card is inserted, only a limited service is available. See Making an emergency call on page 19 for more information. Setting the phone language and time zone The first time you turn on your phone, you will be prompted to select your language. This will be the display language. Select your language from a list using the navigation keys and the centre selection key. See Setting phone language on page 46 for more information. After you have selected your language, you will be prompted to select your time zone. Your phone automatically receives universal time (UTC) from GPS satellites. By selecting the time zone, the phones clock will display your local time. If you move into another time zone, you will need to change this setting. See Setting the time and Setting the time zone on page 49 for more information. Using info Important information about the status of your phone is displayed in the information shortcut Info on the main screen. These include missed calls, new messages, voicemails, todays organiser appointments, active profile status, your phone number and your service providers number. Info will pop up on the main screen if you have missed a call or have new messages or voicemails waiting. To access Info at other times, press the centre selection key. When Info is open, use the navigation keys to highlight the information you wish to access and press the centre selection key to open. Accessing important information about your phone Important information about your phone is displayed under Menu > Settings > About. These include your model, firmware version, IMEI number and IMSI number. You may need to supply this information when contacting your service provider. Upgrading your phone From time-to-time it may be necessary to upgrade your phones software in order to improve its functionality and operation. Inmarsat or your service provider will contact you if your phone needs upgrading. Run the USB drive supplied with your phone to download the Firmware Upgrade Tool and to access the How to upgrade your phone guide. These are also downloadable from inmarsat.com/isatphone. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 13 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 14 Your IsatPhone makes and receives calls by communicating with Inmarsat satellites in orbit above the equator. Your phone antenna must be deployed and there must be a clear line of sight to an Inmarsat satellite for you to make and receive calls. Connecting to the satellite Switch your phone on, hold down the red key few seconds until the screen lights up. The Inmarsat logo will appear followed by the main screen. for a If prompted to enter a PIN, enter the PIN code. The PIN is originally set by your service provider which you can reset. See Setting up SIM PIN code on page 55 for more information. Stand outside with a clear view of the sky with the phone antenna pointing upwards. There must be a clear line of sight between the phones antenna and the satellite. The more sky you can see the stronger the signal should be from the satellite. If open sky makes up about 70%

of your view when you look up, then the signal should be strong. Searching satellite will appear on the screen. When your phone is connected to the satellite, the screen will display Ready for service. The top left of the screen will display Inmarsat. The signal bars indicate the signal strength. At least two signal bars are required to make and receive calls. USING YOUR ISATPHONE 2W Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 15 Using the eCompass function In order to connect to the network, the handset needs to acquire a GPS fix. This happens automatically. If you are unable to obtain a GPS fix, or your fix is out of date, your search will fail and a red circular icon will be displayed in the status bar on screen. The handset will display information to assist you in acquiring a GPS fix. To maximise your chances of obtaining a GPS fix as quickly as possible, stand outside with a clear view of the sky. Finding a satellite If the handset is unable to register to the network, or if the received signal strength falls during a call, the eCompass function is automatically displayed on-screen. It helps by showing the direction towards the best Inmarsat satellite. In response, you must point the antenna until the on-

screen satellite image turns green. You need to ensure that, in the direction indicated, there is clear line of sight to the sky and no obstructions. The eCompass is never displayed while the handset is correctly connected to the network. When it appears, turn towards the satellite in the direction indicated. The on-screen satellite image changes to green to show that you are pointing the handset in the correct direction. Then press Search. Improving signal strength If the received signal strength falls during a call, as shown by the signal strength indicator, ensure that the antenna is pointed towards the satellite and there are no obstacles between you and the sky. The eCompass is displayed to indicate the direction in which the antenna should be maintained. When you return the handset to your ear, ensure that you keep it pointed in the direction of the satellite. Obtaining a GPS fix Before you can make a call, your phone needs a GPS fix so it can be located by the satellite. This happens automatically but if a new GPS fix is needed, the GPS fix the open with a clear view of the sky until the disappears. Your phone is now ready to make and receive calls. See Obtaining a GPS fix manually on page 39 for more information. icon will be displayed. Keep the phone in icon Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 16 Making and Receiving calls 1 Switch on your phone by holding down the red key for several seconds. 2 Stand outside with a clear view of the sky and the antenna pointing upwards. 3 Check your phone is connected to the satellite network - Inmarsat is displayed at the top left of the screen. 4 Ensure you have at least two bars of signal strength. 5 Ensure there is sufficient battery power. 6 Ensure that your phone has a GPS fix the GPS fix required icon is not displayed. 7 Dial the full international number and press the green key, eg. +44 1621 123456

. 8 To end a call, press the red key

. 9 Switch off your phone by holding down the red key until the screen shuts down. Making a call Enter the full international number by dialling either +

(hold down the 0 key for 3 seconds) or 00, country code, area code (without the leading 0), telephone number and

, eg. 00 44 1621 123456 press the green key

+ 44 1621 123456

. A Calling message and the name of the person being called (if listed in your Phonebook or SIM contacts) will display on the screen. When the call is answered, the screen will show the call time in minutes and seconds. To end the call press the red key or

. Making a call from saved contacts Select Menu > Contacts > Phonebook. Scroll to the desired name using the navigation keys, or enter the first letter of the name in the search field. The matching contacts will be listed. Highlight the name and press the

. See Phonebook and Contacts on page 41 green key for more information. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 17

, select from the list of previously Re-dialling a number Press the green key dialled numbers using the navigation keys and press to start the call. Your phone stores 30 the green key dialled numbers. Alternatively, select Menu > Call log >

Dialled calls, select the person you wish to call and press the green key

. Re-dialling automatically To switch Auto re-dial on or off, select Menu > Settings >

Call settings > Auto re-dial and make your selection. The default setting is off. When activated, if your call did not complete, your phone displays Retry? and the reason why the connection was unsuccessful. Press Select to automatically re-dial the number three times until the call is answered. If you press any key or receive a call during this time, re-dialling is interrupted. If the re-dial is successful the phone beeps, then rings. Select Close if you do not want to retry. Receiving a call To receive a call, your antenna must be deployed and your phone connected to the satellite. Press the green key it. You will see Call from followed by either the name of the caller (if listed in your Phonebook or SIM contacts), the calling number, or Number unknown. to accept the call or press the red key to reject If you do not wish your phone to play a ringtone, set your active profile to silent or vibrate only. See Sounds, ringtones and profiles on page 46 for more information. To mute the ringing tone when a call comes in, press Silence. Declining a call

. The call is disconnected and the Press the red key caller details are stored in Missed calls for later retrieval. Returning a call Your phone automatically stores the numbers of the last 20 phone calls you have answered or missed. To return a call, select Menu > Call log. Select the appropriate folder, eg. Missed calls or Received calls, highlight the contact and press the green key

. Making a call while on another call You can put your current call on hold and make a second call at any time. Select the contact by selecting Options >

Contacts > Phonebook or by dialling the full international number. When you press the green key

, your current call will automatically be put on hold. By selecting Swap you can switch between calls at any time. You can end either call at any time by selecting Options > End held call or End active call. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 18 Receiving a second call while on a call The incoming call will be diverted to your voicemail unless you have set up Call waiting. See Setting up call waiting on page 24 for more information. Using call waiting When Call waiting is activated, a pop-up and an audible alert will notify you if another caller is calling you when you are on another call. When you receive this alert you can press the green key to accept the second call. The first call is placed on hold automatically while the second call is taken. By selecting Options > Swap you can switch between calls at any time. You can end either call at anytime by selecting Options >

End held call or End active call. If you receive a third call while you have one active and one held call, the name or number of the caller will be displayed. Ending either the active or the held call will automatically answer the new call. If you wish to disconnect the first call to accept the second, select Options > End active call. The call is disconnected and the caller details If you do not wish to accept the second call, press the red key are stored in Missed calls and Info for later retrieval. If you do nothing, the second caller will be diverted to your voicemail. If voicemail has not been activated, then the call will appear as a missed call. See Setting up call waiting on page 24 for more information. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 19 Making an emergency call Wireless phones, including IsatPhone 2W, operate using radio signals, wireless networks, landline networks, and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never rely solely on any wireless device for essential communications like medical emergencies. Emergency calling requirements for satellite phones vary from country to country. Always check your emergency contact numbers and ensure they are stored on your phone before travelling. Please contact your service provider for specific country information. To make an emergency call in the US, dial 911 or 112 and in Australia dial 000 or 112. Your call will be put through to a call centre which will connect you to the appropriate emergency service. Alternatively, select Menu > Contacts

> Emergency numbers. An emergency call is free of charge. Prepay users do not need a positive balance to make an emergency call. Dialling 911 or 112 overides all security locks and bars on your phone. For details on emergency calling in the rest of the world, please contact your service provider. Making conference calls Your phone can host conference calls with up to five participants. To initiate a conference call, call the first participant. When the first participant is connected, call the second participant by selecting Options > Contacts

> Phonebook, select the second participants name and press the green key

. When the second participant is connected, select Options > Conference. You are now in a three-way conference call. Repeat for more participants. To end a conference call, select End or press the red key

. To answer a new inbound call, press the green key or select Options > Answer. The conference call will be placed on hold. To place all participants into one call, select Options > Conference. To place an inbound call into conference without answering it first, select Options > Add waiting to conference. To disconnect individual conference callers, select Options

> Disconnect caller and press Select, or the centre selection key. A list of the participants is displayed. Select by highlighting their name or number and press Select, or the centre selection key, to disconnect them from the call. To speak privately to one participant during a conference call, select Options > Private with a caller and select from the list. To resume the call with all participants, select Options > Conference. To put individual participants of a conference call on hold, select Options > Hold conference party and choose from the list of current callers displayed. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 20 Incoming call alerting To make or receive calls and messages with any satellite handset, you must maintain a clear line of sight between the antenna of your handset and the satellite. The Incoming call alerting feature notifies you of calls and text messages when satellite signal reception is limited and/or when the antenna is not deployed. Access to the service is still affected by the location of the handset, and is not available when out of the line of sight of the satellite. See Connecting to the satellite on page 14 for normal operation. Using Incoming call alerting Before using Incoming call alerting, each time you switch on the handset it must be successfully registered to the network. To do this, deploy the antenna in a location that has a clear line of sight to the satellite. When the handset is registered, the screen displays Ready for service and the two status LEDs change to green. See Connecting to the satellite on page 14. You can now stow the antenna and place the handset in the holster provided or in another convenient location. Unless Incoming call alerting is disabled, the screen displays Ready for service, Incoming call alerts only and the status LEDs change to amber to indicate that the available signal strength is sufficient to notify you of incoming calls or messages. If the received signal strength is too low, the status LEDs turn red and the screen displays the instruction Point antenna towards satellite. Move to a location with a clear line of sight to the satellite and the two status LEDs will change to amber. The handset will continue to search for the network until you reach a position where the signal strength is sufficient to receive incoming call alerts. Receiving an Incoming call alert When you receive an incoming call alert, you must action in order to obtain full connectivity to the network. This means that you must deploy the antenna if it is stowed, and move to a location with a clear line of sight to the satellite. On receiving an incoming call alert, the status LEDs flash amber and the alert tone sounds. See Sounds, ringtones and profiles on page 46. The screen displays Incoming call and Time remaining 15s. The time counts down until you successfully connect to the network. Throughout this period, the incoming call can be rejected by pressing the red key. Missed Incoming call alerts If you reject an incoming call alert or do not successfully connect to the network within 15 seconds, the alert is terminated. The screen then informs you of a missed alert . You must connect to the network to receive more information about the missed call, voicemail or text. See Returning a call on page 17. Missed calls are forwarded to your voicemail if configured to do so. See Using voicemail on page 22. Incoming call alerting 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 21 Calling handsfree You can also use your phone in handsfree mode. Place the phone on its side with the antenna pointing upwards and use loudspeaker or a handsfree headset. Loudspeaker can be activated at any time during the call. To use the wired handsfree headset, connect it to the audio port at the base of the phone, under the protective cover. To use a Bluetooth headset, see page 50 for more information. Configuring the Incoming call alerting feature By default, Incoming call alerting is set to On. To switch this feature off, go to the main menu and choose Settings

> Call settings > Incoming call alerting. Set the status to Off and press Select. To switch the feature on again, at the main menu choose Settings > Call settings >

Incoming call alerting, set the status to On and press Select. By default, Incoming call alerting is set to provide notification of voice calls only, but you can configure the handset to notify you of text messages as well. Go to the main menu and choose Settings > Call settings >

Incoming call alerting, then choose Configure alerts. The screen displays the options Alert for calls only and Alert for calls & messages. For notification of calls and messages, choose the latter option and press Select. Using the volume control The two volume keys on the side of the phone adjust the call volume. Muting a call Select Options > Mute while on a call. To cancel, select Options > Unmute. Using loudspeaker Select Loudspeaker at any time during a call. Incoming call alerting 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 22 Using voicemail You will be able to receive voicemail messages if your service provider has enabled voicemail. Your phone automatically checks for voicemails shortly after it has been switched on and connected to the network. It will also send you voicemails that arrive while you are connected to the network. will If you have a new voicemail, the voicemail icon appear in the status bar at the top of the main screen and in Info. To listen to the message, hold down the key on the keypad for a few seconds and your phone will automatically connect you to your Inmarsat voicemail. Alternatively, you can dial the short code 570 followed by or the full international number 00 870 the green key 772 001 899 or + 870 772 001 899 and the green key

. Follow the spoken instructions. The default language for voicemail is English, but your service provider may have enabled your voicemail in your chosen language. If you wish to change the voicemail language, follow the spoken instructions or contact your service provider. Additional call features Viewing call length Your phone logs the duration of outgoing and incoming and Dialled calls appears, calls. Press the green key which lists the date, time and duration of each call. Use the navigation keys to access Received calls and Missed calls. Alternatively, select Menu > Call log and make your selection. You may find the Call duration log useful for checking the Last dialled call duration, and the total time of Dialled calls. To reset the counter, highlight the value you wish to reset, select Options > Clear and press the left navigation key labelled Select. To reset all counters, select Options > Clear timers. Setting the minute counter Select Menu > Settings > Call settings > Minute counter and select your preferred setting. The default setting is off. When enabled, your phone will beep after every minute of your call. Additional call features 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 23 Setting up call summary Select Menu > Settings > Call settings > Call summary and then use the navigation and centre selection keys to make your selection. The default setting is on. When Call summary is activated, the date, time and duration of the call is displayed. Setting up and using speed dial First, select Menu > Settings > Call settings > Speed dialling and then use the navigation and centre selection keys to make your selection. The default setting is on. Eight speed dial slots are available, from 2-9. Speed dial 1 is reserved for voicemail. From the main screen, press and hold down for a few seconds the number key that you would like to associate with a contact. If the number is not yet assigned, a pop-up will ask if you wish to assign a contact to the key. Select Yes and a list of Phonebook contacts is displayed. Use the navigation keys to highlight the contact and then the contacts details. Press OK to save your selection. Alternatively, select Contacts > Phonebook. Use the navigation keys to highlight the contact name, press the centre selection key to open or select Options > Open. Highlight the number to which you would like to assign the speed dial, eg. Mobile. Select Options and select Assign speed dial. Highlight a speed dial slot marked Unassigned, press the centre selection key to assign the phone number to that speed dial slot. To remove speed dial, follow the instructions above and select Remove speed dial. To speed dial, hold down the appropriate number of the keypad for a few seconds and the phone will automatically dial the number. Setting any key answer Select Menu > Settings > Call settings > Any key answer and select On. The default setting is off. When activated, press any key to answer a call. Deleting all call logs Select Menu > Call Log. Select Options > Clear all. Press Yes to confirm. Additional call features 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 24 Advanced call features Advanced call features are controlled by the Inmarsat network. To check or change these features, the phone must be connected to the satellite with a signal strength of at least two bars. Call barring An IsatPhone 2W SIM card always uses an international number format, + or 00, and the country code, 870. Call barring prevents the following call types from being made or received by your phone:

Sending your caller ID Select Menu > Settings > Call settings > Send my caller ID, then select On, Off or Set by network and press OK. Set by network leaves it to the network to select whether Caller ID is displayed. The default setting is Set by Network. When Send my caller ID is on, your caller ID will be displayed on the recipients phone. If this feature is switched off, your caller ID will be hidden and Withheld displayed in its place. Setting up call waiting Select Menu > Settings > Call settings > Call waiting, and select Activate. There may be a short delay before the network responds. Call waiting activated will appear when the setting has been enabled. The Call waiting default setting is off. From the Call waiting menu you can also select to Check status or Deactivate. To use call waiting, see Using call waiting on page 18 for more information. Outgoing calls: bars all outgoing calls International calls: bars all outgoing calls except to other Inmarsat numbers International except to home: bars all outgoing calls except to other Inmarsat numbers Incoming calls: bars all incoming calls Incoming outside home: bars all incoming calls except from other Inmarsat numbers Note: This feature is not supported in all countries. If you are using a SIM card with local country numbering, the call barring is as described by the menu. The first time you set up call barring, you will need to reset the barring password. Select Menu > Settings > Call settings > Call barring. Select Options and navigate to Change barring pass code. Enter the barring pass code and select OK. The default is 0000. Enter a new four-digit pass code and select OK. Then enter the new pass code again to confirm it. You will need to enter this new pass code whenever you change your call barring settings. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 25 To cancel a bar, highlight that type of call in the Call barring menu, select Options and select Cancel. To cancel all call barring, select Options and select Cancel all barring. To check the status of a call bar, highlight that type of call in the Call barring menu, select Options and select Check status. The barring code can be entered incorrectly an unlimited number of times. If you have forgotten your code, please contact your service provider. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Call barring and Call divert cannot be active at the same time. Diverting calls Select Menu > Settings > Call settings > Call divert. Call divert allows you to forward incoming calls to your voicemail or another phone number:

Only voice calls diverts any voice call to your voicemail or another number Only data calls diverts data calls to another phone number Only fax calls diverts fax calls to another phone number If busy when you are engaged on another call, this option diverts calls either to your voicemail or to another number If no reply this option allows you to select how long your phone should ring (up to 30 seconds) before the call is diverted to your voicemail or another number If out of reach when you are out of reach of a satellite signal this option diverts calls either to your voicemail or to another number If not available diverts all If busy, If no reply and If out of reach calls. If you subsequently assign a divert number for any of these calls, that number will override the If unavailable divert number After making your selection, you will be prompted to enter the phone number or voicemail to which calls are to be diverted. Select Options to select a number from your phonebook. To cancel call divert, highlight that type of call in the Call divert menu, select Options and select Cancel. To cancel all call diverts, select Options and select Cancel all forwarding. To check the status of a call divert, highlight that type of call in the Call divert menu, select Options and select Check status. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Call barring and Call divert cannot be active at the same time. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 26 Fixed number dialling can restrict your phone to a certain prefix, as well as individual phone numbers. To limit outbound calls or text messages to a specific country or range of corporate numbers, create an FND list entry with the international prefix and local prefix you wish to allow, followed by the correct number of remaining digits replaced by question marks. Press the * key twice to enter a question mark. Example: To limit calls to UK landlines, create an FND list entry: +44??????????. Substitute any number in place of the ? symbols while dialling or sending a message. When fixed number dialling is activated, your phone still enables numbers stored in other areas of Contacts to be viewed. Fixed number dialling (FND) When Fixed number dialling is activated, the user is limited to dialling or texting only numbers stored in the FND list. The default setting is off. Activating and de-activating fixed number dialling Select Menu > Settings > Security, highlight Fixed dialling from the list and press the centre selection key. Select On to activate and press the centre selection key or OK. You will be prompted to enter your PIN 2 code. The default PIN 2 is 9999. See Setting up SIM PIN 2 code on page 55 for more information. Contact your service provider if this code was not specified or was reset at purchase. To add a number to your list, select Menu > Contacts >

FND list and press the centre selection key. Press Options and select either New FND contact or Copy from phonebook. You will then be prompted for the PIN 2 code. FND list entries are stored on your SIM card. Only one name and one contact number can be stored for each entry. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 27 Using fixed number dialling Select Menu > Contacts > FND list and the contact. Select Call or Send message from Options. To send email messages when fixed number dialling is activated, the message centre number should be added to the FND list. See Message settings on page 33 for more information on finding your message centre number. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Messaging Using the message menu Select Menu > Messaging. Select any one of the following options and press the centre selection key or select Options > Open. The functions are:

New message - to create a new message Inbox - to store received messages Outbox - to temporarily store messages waiting to be sent. Messages are placed in Outbox, for example, when your phone is not connected to the network. If sent, messages will be stored in Sent. If unsent, messages will be stored in Drafts Drafts - when a message is written but not ready or able to be sent, the message is saved here Sent - to store the sent messages. If you want your sent messages to be saved, select Menu > Messaging >

Options > Settings > Text msg settings > Saving sent messages and select On Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 28 Saved messages - to store received messages Using predictive text entry Templates - If you regularly send similar messages, you can set up a template. To do this, compose a new message, select Menu > Messaging > New message >

Text message and compose the parts of your message that will not change. Select Options > Save as template. To compose a new text message based on this template, select Menu >

Messaging > Options > Compose from template and then select the template you would like to use. Edit the text, add recipient and then select Options > Send SIM messages - to store messages in SIM memory. A total of 125 messages can be stored in the phone memory. Entering text You need to enter text when composing a message, adding a contact to your phonebook, adding an appointment to your organiser or searching. Your phone offers two types of text entry mode: predictive and standard. Predictive text mode allows you to use less keystrokes to type a word as it uses a built-in dictionary as a time-

saving feature. For example, to type the word hello, you would only use 5 keystrokes (one for each letter of the word). When you type h (number 4 on the keypad) a list appears on the screen. It is not necessary to select the letter h as when you type e (number 3) the dictionary begins to narrow down the words that begin with he. Key number 5 twice to type ll, then number 6 for the letter o. This will result in the dictionary selecting the only known word with these sequential letters, ie. hello. If the dictionary has a number of options for the same keystrokes it will present a list of words. Use the down arrow to scroll to the word you require and press the centre selection key. As always, press the 0 key to create a space between words. If the word you are typing is not in the dictionary, Word not in dictionary appears. Press OK and select Spell word, type the word you want to enter and press Select. The new word is now saved in your dictionary for future use. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 29 You can change the text entry settings whilst composing a message. Click and hold the # key. A pop-up menu offers options to change the language, text editing mode or to add a new word. Note: To change the language of the dictionary used while composing a text message, select Options >

Writing language. Using standard (non-predictive) text entry Standard text entry enables you to key text in manually, letter by letter, without the phone suggesting the word you are attempting to type. To enter text, repeatedly press a number key, 2-9, until the desired character appears. For numbers, hold the key down longer until the number appears. To insert a space, press the 0 key. For symbols such as punctuation marks, press the * key and then use the navigation keys to select from the menu. Press the # key to change text editing and capitalisation. To delete text, place the cursor to the right of the character you wish to delete and select Clear. Move the cursor around the message using the navigation keys to insert or delete text anywhere in the message. Selecting text entry mode The icon at the top right of your screen displays your choice of text entry mode and character case. The default setting is standard text. If you want to change the text entry mode press the # key repeatedly until your chosen mode icon is indicated. The modes are:

Predictive mode all capitalised Predictive mode initial capital only Predictive mode no capitals Standard mode all capitalised Standard mode initial capital only Standard mode no capitals Standard mode numbers only Standard mode symbols only Creating a text message The character limit for a text sent from your phone is approximately 1600 Latin characters or 740 non-Latin characters, ie up to 10 concatenations, including the recipients telephone number. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 30 Select Menu > Messaging > New message > Text message. A blank screen will appear. Compose your message. See Entering text on page 28 for more information. When you have finished, add the recipient(s). If their details are already stored in your Contacts select Options > Add recipient and select the name from the list. Use the left and right navigation keys to move between Phonebook and SIM contacts. If the recipients details are not stored, use the up navigation key to move the cursor to the To: line. Enter the recipients full international number. If you make a mistake, use the left and right navigation keys to move the cursor and Clear to delete a number. When you have finished adding recipients, select Options

> Send or press the centre selection key. If you want to save your message so you can edit or send it later, select Options > Save, or select Options > Exit and confirm that you want to save the text. The message will be saved in the Drafts folder. When you are ready to complete it, select Menu > Messaging > Drafts. Creating a text message for sending to an email address Your phone can also send text messages to email addresses. Instead of displaying your name to the recipient the message will display your details in the following format:

From: your phone number message.inmarsat.com eg. From: 8707764XXXXX message.inmarsat.com The character limit for a text sent from your phone to an email address is approximately 1600 Latin characters or 740 non-Latin characters, ie up to 10 concatenations, including the recipients email address. Select Menu > Messaging > New message > Email message. Compose your message. Recipients can be added from stored contacts by selecting Options > Add recipient. Only entries containing an email address will be displayed. To send your message to an email address which is not stored, use the up navigation key to move the cursor into the To: field and type the address. For symbols such as the

@ sign, press the * key and then use the navigation keys to select from the menu. After entering the address, wait for 5 seconds and the phone will place a ; after the entry, allowing you to enter another address. When you move the cursor away from the To: field or open Options, your phone will check the email addresses entered. If addresses do not follow the format of a valid email address, they will be deleted and an error message displayed. Receiving text and email messages Messages can be received when the antenna is deployed and your phone is connected to the network, even if you are on a call, or when incoming calls are forwarded to another phone number. If your phone is switched off when a message is received, the message is stored by the network until your phone is switched on and registered with the network. Delivery will be attempted for the duration that your message Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 31 remains in the network. To check or change this setting, select Menu > Messaging > Options > Settings > Text msg settings > Validity period. When you receive a message on your phone, an unread message will appear on the status bar. Info will pop-up and display a list of unread messages. If you wish to read the message later, press Close. To read the message, select Menu >

Messaging > Inbox. Alternatively, with Info open, use the centre selection and navigation keys to highlight and open Unread messages. icon Incoming text messages accommodate the full 10 concatenations. However, incoming messages from emails are restricted to approximately 160 Latin and 74 non-Latin characters. If the sender exceeds this limit, the message will be truncated upon receipt. Viewing your received messages Inbox lists the last 20 messages received, including message status (read or unread), the senders name or number, the first words of the message and the date received. Use the up and down navigation keys to highlight a message and press the centre selection key or select Options > Open. Replying to sender Open the message and select Options > Reply. A new blank message will be displayed. Complete the fields as prompted. Forwarding a message Open the message and select Options > Forward > Text message or Email message. The message is displayed with the cursor flashing in the empty To: field. Enter the recipients number or to add a contact from the phonebook, press Options > Add recipient. When the To: field is completed, select Options > Send. A pop-

up confirms that the message has been sent. The sent message is stored in the Sent list. Calling a number from a received message Open the message and press the green key Options > Call. After the number has been called, the message is considered read and remains in the inbox. or select Saving details from a received message Open the message and select Options > Address clipboard. The senders number is displayed. Select Options > Add to contacts. You can either Create new or Update existing. Select which field to save the number in the contacts list, complete other fields as appropriate and select Options > Save. The contact will be stored in Phonebook. See Creating a new contact on page 40 for more information. Saving a received message To save a received message, open the message you wish to save and select Options > Copy to folder >

Saved messages. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 32 Deleting messages Select the message from the list displayed in any of the message folders and select Options > Delete. A pop-up will appear asking you to confirm the action. Press Yes. To delete all the messages in the folder, select Options >

Delete all messages. Setting up message groups If you regularly send the same text or email message to the same group of people, you can set up a group. Select Menu > Contacts > Groups, then select Options > Create new. Enter a name for your group and select OK, followed by Yes. You can set up a maximum of 20 groups, and the same contact can be a member of more than one group. To add members to a group, select Menu > Contacts >

Groups, highlight the group to which you would like to add members and press the centre selection key. Now select Options > Add member. This will retrieve your phonebook. Highlight the name of the contact you would like to add to the group and press the left or centre selection key. A group can have any number of contacts. By selecting Options when a member of the group is highlighted, you can also:

Open the contacts details Call the contact Send a Text message to the contact Remove from group to remove the contact from this group View group list to view the members of each group Assign group ringtone to give all members of this group the same ringtone, so that you will be able to recognise when a member of the group is calling you. To send a text message to the whole group, select Menu > Messaging > New message > Text message or Email message > Options > Add recipient and then press the right navigation key three times to move between the tabs. Select the group from the list and compose your message. You can also add members to groups directly from your phonebook. In your phonebook, simply highlight the contact, select Options > Add to group, then select which group to which you would like to assign the contact. You can also see which members belong to a group by selecting Options > Belongs to group. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 33 Sending a text to a group of people If you regularly send the same text to a group of people, you can create a group in your phonebook. To send the text to a group you have already set up, select Options

> Add recipient and then press the right navigation key twice to display the list of groups. Using message settings Select Menu > Messaging > Options > Settings >

Text msg settings or Email settings. Text message settings:

Use same message centre: Always set to Yes. SMSC management: Both specify the number to which your phone will despatch your messages for delivery. Validity period: Specifies the length of time your message will remain in the network, should it be pending for delivery to the recipient. Saving sent messages: The default setting is on. The setting can be changed if required. Long message sending: The default setting is on. This allows approximately 1600 Latin or 740 non-Latin characters to be sent ie. up to 10 concatenations. With original text / Without original text: The senders original message is included/excluded as part of any reply that you compose. The default setting is Without original text. Set defaults: This resets all message settings. Entering your service centre number It is unlikely that you would need to enter or change your service centre number unless advised to do so by your service provider. The number of your service centre is required in order to send messages. In the unlikely event that this detail is not on your SIM card, you can enter the number yourself. To enter a service centre number, select Menu >

Messaging > Options > Settings > Text msg settings >

SMSC management. If the phone number of your service centre is displayed, select Options > Exit. If there is no number in the display, select Options > Edit and enter the full international number of the service centre. You will be prompted to activate the number. Press Yes. Your phone is now ready to send and receive messages. Alternatively, select Menu > Messaging > Options > Settings > Email settings > Options > Edit and add the email centre number and select Apply. Setting a message delivery expiry period If your message cannot be delivered, you can change the length of time your message will remain in the network. To check or change the expiry period select Menu >

Messaging > Options > Settings > Text msg settings >

Validity period. Messaging 1 2 3 4 5 6 7 Prepay services If you have a prepay subscription, your service provider will have informed you of the services available to you. Your phone also enables you to make a balance enquiry and redeem prepay vouchers for Inmarsats prepay service, free of charge. Select Menu > Settings > Prepay, then select either Balance enquiry or Redeem voucher and follow the on-screen instructions. Making a balance enquiry From the main screen enter your balance enquiry code,

*106# and press the green key

. Your current balance and expiry date will be shown on the screen. Redeeming a prepay voucher From the main screen enter the top-up code,

*101*VoucherNumber#, eg. *101*1234567890123456#

and press the green key

. Your new balance and expiry date will be shown on the screen. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 34 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 35 Using the Assistance button In a critical situation, the Assistance button allows you to rapidly make a call to a recipient, or send an alert text message or email to one or more recipients. Note: An assistance alert is not the same as an emergency call, see page 19. You cannot set the feature to call a national emergency number (e.g. 911) or other numbers of less than four digits. However it is always good practice to save to your phonebook the contact details of related local services so that they can be alerted if necessary. Enabling the Assistance feature Before you can use the Assistance feature, you must enable it and configure the alert type and recipients. From the main menu select Location services > Assistance button > Configure > Assistance feature. Then press the centre selection key to enable the feature. Configuring Assistance button calls Go to Location services > Assistance button >

Configure > Alert type, then select Call only or Call &

message. Choose the intended recipient of your call by selecting Location services > Assistance button >

Configure > Call config. > Edit recipient. You can choose a contact from the phonebook or add a new contact. To find contacts, edit contacts or add new contacts, see Managing contacts in your phonebook on page 41. You can only select one recipient for an assistance call. If you want to use the handset loudspeaker when you make an assistance call, select Location services > Assistance button > Configure > Call config. > Handsfree call

> On. If you want the handset to automatically redial the recipient when the call setup fails, select Location services > Assistance button > Configure > Call config.

> Call retry > On. If the first call is unsuccessful, the handset disconnects and shows the text Call connection failed, retrying. The contact is then automatically re-

dialled after three minutes. The handset will make up to eight attempts to connect to the recipient, after which Assistance alert is de-activated. Configuring Assistance button messages Go to Location services > Assistance button >

Configure > Alert type, then highlight Call & message or Message only and press the centre selection key. Choose the intended recipient of your message by selecting Location services > Assistance button > Configure

> Message config. > Edit recipient. See Configuring assistance calls above. Then choose the type of message that you want to send to this recipient by selecting Email message or Text message. If you want to send a message to more than one recipient, select each contact from the LOCATION SERVICES Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 36 phonebook separately (adding new contacts if necessary) and choose the message type for each. A maximum of ten message recipients is permitted. Created 20140202T132216Z is the timestamp giving the date and time at which the alert was triggered The content of assistance messages is automatically created by the handset. It always includes an up-to-date GPS fix, the time at which the fix was acquired and the time that the alert was triggered. An email cannot exceed 160 characters, including the recipients email address, and users cannot personalise messages by entering additional text. Here is an example of an assistance message:

Assistance alert from:

+870776400465 52.123N,22.456W 20140202T125959Z h:08m,v:32m accuracy Created 20140202T132216Z where:

+870776400465 is the senders phone number 52.123N,22.456W is the latitude and longitude of the senders location 20140202T125959Z is the date and time at which the GPS fix was acquired h:08m,v:32m accuracy is the horizontal and vertical accuracy of the GSP fix in meters Activating an Assistance button alert With your handset switched on and the antenna deployed, flip open the latch of the Assistance button at the top of the handset and press the button revealed. Alternatively, from the main menu, select Location services >

Assistance button > Configure assistance button >

Send assistance alert. The on-screen text informs you that the alert will be sent in 15 seconds and that you can select Alert now to send it immediately. You can cancel the alert during this time, by pressing Cancel. Respond as necessary. If alert messages have been configured, they are then sent to the recipient(s). If alert call has been configured, then the call is established. During the call, the screen displays the latitude and longitude of your current location. Assistance button security You can lock the Assistance button feature to prevent unauthorised use. If the lock is on, you must enter the admin code before the features settings can be changed. See Setting up the admin code on page 54 for more information. The lock default setting is Off. To switch on or off the Assistance button lock, select Menu > Settings > Security and select Assistance button lock from the list. Then select On or Off, enter the admin code and press OK. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 37 Using the Tracking feature The Tracking feature allows you to send text messages or emails reporting the GPS coordinates of your current location to one or more recipients or, alternatively, to a tracking portal. The messages are automatically generated by the handset, with updated coordinates, at a default preset interval of 15 minutes. To send any message, your handset must be registered to the network. See Connecting to the satellite on page 14. Configuring Tracking Tracking status The Tracking feature has three states - Enabled, Disabled and Always-on - that control access to the sending of tracking messages. To configure the status, go to the main menu and choose Location services >

Tracking > Configure tracking > Tracking status. Then choose a state:

Enabled: allows you to start and stop sending tracking messages, either by navigating the menu or by using the Tracking button [graphic] above the volume up/

down keys on the side of the handset Disabled: removes the ability to start or stop the transmission of tracking messages Always-on: The handset continues to send messages whenever it is connected to the network Choosing the message recipients and message type Select Location services > Tracking > Configure tracking > Edit recipient. You can choose a contact from the phonebook or add a new contact. To find and edit contacts or to add new contacts, see Managing contacts in your phonebook on page 41. If you want to send messages to more than one recipient, select each contact from the phonebook separately (adding new contacts if necessary). A maximum of ten recipients is permitted. When you have chosen a recipient, press Select. The message types available for that contact are displayed, highlight Text message or Email message and press Select. Note that a recipients email addresses cannot exceed 40 characters. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 38 Choosing the message interval When Tracking is set to On, messages are automatically sent every 15 minutes by default. To stop sending tracking messages when Always-on has been selected, change the status by choosing Location services > Tracking > Configure Tracking > Tracking status > Disabled. You can increase or decrease this interval to suit your requirements. Select Configure tracking > Edit interval. The screen displays preset time intervals. Highlight an interval value and press Select. You can also specify your own interval of up to 9999 minutes by choosing Custom interval from the list of intervals. A blank text box is displayed. Type the interval that you want to use and press OK. Starting tracking If the Tracking status is set to Enabled, you can start and stop sending tracking messages by using the Tracking button. Alternatively, from the main menu choose Location services > Tracking > Start. On-screen text confirms that tracking messages will be sent at the chosen interval. Press OK. If you have chosen Always-on override, tracking messages are sent whenever the handset is registered to the network. The tracking LED above the screen flashes when Tracking has started. Stopping tracking To stop sending tracking messages, press the Tracking button or choose Location services > Tracking > Stop and press Select. An on-screen prompt asks you to confirm, press OK. The tracking LED goes off. Tracking security You can lock the Tracking feature to prevent unauthorised use. If the lock is on, you must enter the admin code before you can change the Tracking features settings. See Setting up the admin code on page 54 for more information. The lock default setting is Off. To switch Tracking lock on or off, select Menu > Settings

> Security and select Tracking lock from the list. Then select On or Off, enter the admin code and press OK. Using your GPS location information As well as locating your phones position for the satellite, you can also view your GPS location and send it as a text message or email. Note: You can view GPS information only after the phone has been registered to the network. Viewing your GPS location information Select Menu > GPS position > Options > View location information to view the date and time of when your last GPS fix was taken and your latitude and longitude at that time. Your exact location is indicated with a white dot on the world map. 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 39 Displaying GPS in metric or imperial measures Select Menu > GPS position. The Valid GPS fix screen appears. Select Options > Set unit and make your selection. The default setting is metric units. Sending your GPS location Select Menu > GPS position and select Options > Send GPS location. The elapsed time since the last GPS fix was obtained is displayed and you are presented with two options. Select Send to use the stored value or New to acquire a new GPS fix. Press the red key cancel. Make your decision on the basis of any significant distance travelled since the stored GPS fix was obtained. Note that requesting a new fix will temporarily delay the sending of your location. to When the GPS fix to be used has been acquired, select Text message or Email message. Only editing of the recipient field is permitted. Enter the destination number or email address directly into the To: field, or choose Options > Add recipient to select an existing entry from Contacts. You are presented with the list of Phonebook contacts. Use the left and right navigation keys to select SIM contacts or Groups. Obtaining a GPS fix manually On rare occasions, your phone may continue to show the GPS fix required icon, which means that a new GPS fix is needed in order for your phone to connect to the network. If this occurs, select Menu > GPS position. The new GPS fix is displayed. When this screen is open, your phone will attempt to refresh the GPS fix every 30 seconds. National GPS policies Some national GPS policies do not allow users to access their GPS information in particular locations. Your phone continues to access the GPS satellites as usual, so its performance is unaffected. However, your phone will not display its GPS location. For more information, please contact your service provider. GPS Data Inmarsat will collect, store and process GPS data in accordance with applicable data protection laws. Personal alert The personal alert feature enables a user to send their GPS position, along with a short pre-configured message, as an email or text message, to a maximum of 10 recipients. Pre-configuration, use of a stored GPS fix and a short-

dial code enable the personal alert to be sent quickly whilst maximising reliability. This is achieved by restricting the alert to one 160 character message, and mailing to each recipient separately. Each message sent is charged separately. Note: Generally, email message routing is more reliable than text messages. Setting up and activating a personal alert To set up and activate a personal alert, select Extras >

2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 34 Using the Assistance button 36 Using the Tracking feature 37 Using your GPS location information 38 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 40 Sending a personal alert The quickest way to send a personal alert is to press

* and # simultaneously for at least 2 seconds from the main screen. Alternatively, select Menu > Extras >

Personal alert > Send personal alert. A pop-up will appear asking you to confirm the action. The antenna must be deployed and your phone connected to the satellite to successfully send personal alert messages. Personal alert > Edit personal alert. Select Configure personal alert, and edit the recipients and the message. See the Messaging section starting on page 27 for more information. The personal alert is made up of the following elements:

Last GPS fix, time of GPS acquisition and fix accuracy Time that the personal alert was triggered on the phone Email address of the recipient if the alert is sent as an email A short message predefined by the user, written in Latin characters. This personalised text is limited in length; a descending counter indicates available characters when editing. The same message is sent to all recipients You can restrict access to the Edit personal alert feature by switching on Personal alert lock in Menu > Settings

> Security and entering the admin code. The default for Personal alert lock is off. See Setting up the admin code on page 54 for more information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Finding a contact You can find a contact in your phonebook either by using the navigation keys to scroll through the list of all contacts or by entering the first characters of a contacts name in the search field at the top of the list of contacts. See Entering text on page 28 for more information. Opening a contact Highlight the contacts name in the phonebook and press the centre selection key or select Options > Open. Use the up and down navigation keys to select a number. Ordering contacts by first or last name Select Phonebook > Options > Settings > Display name order and then select either First last (to list them alphabetically by first name) or Last first (to list them alphabetically by last name). Managing contacts in your phonebook Contacts can be stored in either your phones memory via Phonebook or on your SIM card via SIM contacts. Up to 500 contacts can be stored in the phonebook and up to 250 on your IsatPhone 2W SIM card. To view the contacts in your phones memory, select Contacts from the main screen. Creating a new contact There are several ways to create a contact. From the main screen type in the number to save, including the full international code. Select Options > Add to contacts >

Create new contact. Define the number you are saving, eg. Telephone, Office phone, Mobile phone, Fax etc, then select Options > Save. The saved contact details are displayed. Alternatively, open the contacts directory either by selecting Menu > Contacts or by selecting Contacts. Highlight the location where you wish to save the contact and press Select. The default setting is Phonebook. You are presented with a list of stored contacts, select Options > New contact. Enter the first name, last name and the telephone number. If you wish to save a contact detail other than phone number, select Options > Add detail and select from the list presented. After entering all relevant details, select Options > Save or press the centre selection key. 41 Managing contacts in your phonebook 1 2 PHONEBOOK & CONTACTS Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Deleting a contact Select Menu > Contacts or press Contacts. Select from the list. Use the navigation keys to highlight the stored contact that you would like to delete. Select Option >

Delete. You will be prompted to confirm the deletion by pressing Yes. Deleting all contacts Open your phonebook, select Options, select Delete all and then select Yes. Duplicating a contact Duplicating a contact can be a quick way to add a new contact with similar details to an existing one. Highlight the contact you wish to duplicate, select Options

> Duplicate and then amend the new contacts details. When you have finished, save the new contact by pressing the centre selection key followed by Yes. Editing a contact To change or add details for a contact already in your phonebook, use the up and down navigation keys to highlight the contact, then select Options and select Edit. Move between the details using the navigation keys. Edit the text or numbers. See Entering text on page 28 for more information. To save the changes to the contact, press the centre selection key and then select Yes. Or select Options > Save > Yes. To discard changes, press the centre selection key and when prompted to save changes, select No. Alternatively, select Options > Save > No. See Entering text on page 28 for more information. Calling a contact Highlight the contacts name and press the green key If there is more than one number stored for that contact

(eg. office and mobile) select one of them using the centre selection key. Texting or emailing a contact Highlight the contacts name, select Options > Send message. Select Text message or Email as appropriate. Write your message and select Options > Send. If you are sending a text message and there is more than one number stored for that contact select one using the centre selection key. 42 Managing contacts in your phonebook 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 43 Managing contacts on your SIM card Contacts can be stored on your SIM card as well as in Phonebook. Storing contacts on your SIM card allows you to move contacts from one phone to another. Storing contacts on both the SIM card and the phonebook allows you to back-up your contacts. To view the contacts on your SIM card, select Menu >

Contacts > SIM contacts. You can navigate, edit, delete, make calls or send texts in exactly the same way as Phonebook. To copy a contact from your SIM card to your phonebook highlight the contact in SIM contacts, select Options and select Copy to phonebook. To copy all SIM card contacts to Phonebook, this option arises when the SIM card is inserted. The first time Contacts is accessed after inserting the SIM card, you will prompted to Copy SIM contacts to Phonebook and to confirm the action. Please note that this process may take a little time. To copy a contact from your phones memory to your SIM card, select Phonebook and highlight the contact. Select Options > Copy to SIM. To delete all contacts from your SIM card, select Menu >

Contacts > SIM contacts > Options > Delete all. To find out how many contacts are stored on your SIM card and how many more you can add, select Menu >

Contacts > SIM Contacts > Options > SIM details. Synchronising contacts with Outlook The Contact Synchronisation Tool, supplied with your phone, enables you to transfer contact information held in Microsoft Outlook or Outlook Express on your PC with that stored on your phone. Run the USB drive, supplied with your phone, to download the Contact Synchronisation Tool and to access the How to Synchronise your Contacts guide. These are also downloadable from inmarsat.com/isatphone. Sending and receiving contact details To send a business card, highlight the appropriate contact in your phonebook or SIM contacts folder and select Options > Send business card. Select either Text message or Email message. A text or email message is displayed including all details stored for this contact in the body of the message. Enter the full international phone number of the recipient in the To: field or select Options >

Add recipient to specify a stored contact. Select Options

> Send. When you receive a business card, it will appear as a normal message in your Inbox, but the title of the message will be Business card. Highlight the message and press the centre selection key or select Options > Open. The contact details are presented like any other entry in the phonebook. To save Business card details, select Options > Create new or Update existing. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 44 Business card details are saved to your phonebook. Once the details have been saved, the original message is deleted from your Inbox. Your phone number From the main screen, open Info by pressing the centre selection key and selecting My phone number. Your phone number is usually programmed onto your SIM card by your service provider. If not, the entry will be blank. You can enter the number yourself by selecting Menu > Contacts > My phone number. If a SIM card is subsequently inserted with a stored phone number, your entry will be overwritten. Your service provider number Open Info by pressing the centre selection key and selecting Service provider or for full details select Menu > Contacts > Service provider. These details are programmed onto your SIM card and are not editable. icon is displayed on the status bar. The Alarm You can use your phone as an alarm clock. When set, the alarm alarm will sound for 60 seconds at the same volume as the phone is set to ring. If you do not press a key while the alarm is sounding it will snooze for 9 minutes before sounding again. This will continue until you switch the alarm off. Setting an alarm Select Menu > Alarm and select the type of alarm. Once alarm sounds the next time the clock shows the selected time. Recurrent alarm sounds regularly, on selected days of the week. Enter the alarm time and select OK. If this is a recurrent alarm, use the navigation and centre selection keys to tick which days of the week it should sound, then select OK. Silencing a ringing alarm When the alarm sounds, select Stop or the centre selection key. If you press the right selection key Snooze, it will sound again in 9 minutes. Cancelling an alarm Select Menu > Alarm, select which alarm you would like to remove, then select Options > Remove and confirm your choice. Your phone can be used as a modem to send and receive low rate data. Typical low rate data applications include plain text email and small file attachments. Some Inmarsat service providers offer proprietary applications which have been optimised to operate with your phone. Contact your service provider for details. To enable your handset for the data service:

1 Install the USB Drivers on your PC. To do this, run the USB Drivers supplied with your phone. Download the USB Drivers and access the How to Install USB Drivers guide. These are also downloadable from inmarsat.com/isatphone. 2 Place your phone on its side, raise the antenna and ensure the handset is ready for service. 3 Connect the handset to your PC using the USB cable. 4 Identify the modem COM port to which your phone is connected for the data service. The COM port number will be needed when you are using your data application. To do this, on your PC go to Control Panel > Phone and Modem options and select the Modem tab. You will see IsatPhone 2W Modem and the COM port eg. COM6. Or, go to Control Panel > System and select the Hardware tab. Click on Device Manager and scroll down to Modems. If your USB Drivers are installed you will see IsatPhone 2W Modem. Right click on IsatPhone 2W Modem and select Properties. You will see the Com port eg. COM6. 5 If you have not already done so, install your chosen data application and follow the onscreen instructions. You only need carry out the steps above once. For all subsequent connections, enter your data application and follow the onscreen instructions. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 45 DATA Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 46 Sounds, Ringtones and Profiles Your current sound profile is always displayed in the status bar of the main screen, and can also be accessed via Info. To change your phones sound profile, select Menu >

Profiles, and highlight the one you want and press the centre selection key. There are four sound profiles:

General for everyday use Silent no vibration or sound Loud for noisy environments Vibrate only vibration and no sound You can customise any of these profiles by highlighting it, selecting Options and selecting Personalise. This allows you to change the following aspects of the sound profile:

Vibrate mode on or off Alert volume sound level Keypad volume sound level when a key is pressed Alert ring mode constant, ring once, beep, silent or increasing volume Ringtone the sound your phone makes when it receives a call Key sound the sound your phone makes when a key is pressed Message alert the sound your phone makes when it receives a text message Highlight the setting you would like to change, press the left or centre selection key, use the navigation keys to alter the setting and press Select. To restore the default settings for a sound profile, highlight the profile, select Options > Reset to default. Selecting a ringtone Each profile can play one of 8 ringtones to notify you of an incoming call. Select Menu > Profiles and highlight the appropriate profile. Select Options > Personalise > Ringtone from the list and press Select or the centre selection key. The current ringtone for the profile is played and highlighted in the list. Use the navigation keys to highlight and hear the other ringtone files available. Press Select or the centre selection key to specify the highlighted ringtone. If no sound is heard when you highlight a ringtone, the Alert volume for your profile may be set to 0. This is the default for both Silent and Vibrate only. To change the ringtone volume, select Back to return to Profiles. Highlight Alert volume and press Select. Sounds, ringtones and profiles 1 2 PERSONAL SETTINGS Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 47 Allocating a unique ringtone to callers You can allocate a specific ringtone to a contact. Regardless of the active profile, the allocated ringtone will be used for the specified caller, but the alert volume of the active profile will be respected. Highlight the desired contact entry in your Phonebook or SIM contacts and press the centre selection key or select Options > Open. Highlight the relevant contact detail and select Options > Assign ringtone. From the list of available ringtones, highlight your preference and press Select. The name of the ringtone will be displayed under the contact detail specified. To remove an associated ringtone, open the contact entry, highlight the ringtone and select Options > Remove ringtone. Setting phone and writing language The display and writing language of the phone can be changed by selecting Menu > Settings > Language. Highlight any of the following options and press Select:

Phone language to set the display language of the phone Writing language to set the texting language of the phone Predictive text to set the text editing mode for composing messages Setting phone language The first time you switch on your phone, you will be prompted to select the display language. You can change this at any time. Select Menu > Settings > Language

> Phone language, highlight the desired language and press the left or centre selection keys. If you do not understand your phones current language setting, follow these directions to navigate to the Phone language menu. Press the red key to return to the main screen Press the left selection key to go to the menu screen Press the down navigation key twice to highlight the Settings icon Press the centre selection key to open Settings Press the down navigation key twice to highlight the Language icon and press the centre selection key Press the centre selection key and use the navigation keys to highlight the correct language and press the centre selection key again to change the phones language Sounds, ringtones and profiles 1 2 Setting writing language Select Menu > Settings > Language > Writing language. Select the desired language and press OK. Setting predictive text The predictive text setting is used to set the text editing mode for composing messages. Select Menu > Settings >

Language > Predictive text. Select Available or Hidden. The default setting is available. See Using predictive text entry on page 28 for more details. Setting date and time Your phone automatically receives UTC time from GPS satellites. The first time you use your phone, you will be prompted to select a language from the list, followed by the option to select your local time. When completed, local time will be displayed on the status bar. You will need to reset the time when you travel to different time zones. The Date and time menu lets you change the date and time format. Changing keypad Your phone is supplied with a Latin keypad as standard. Dual-alphabet keypads are available in Latin with Arabic, Japanese or Russian characters. If your phone does not have your preferred keypad, contact your service provider. Setting the time Select Menu > Extras > Date and time > Time settings. Setting the date Select Menu > Extras > Date and time > Date settings. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 48 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 49 Customising display settings Lighting the keypad and screen The backlights for the screen and keypad can be controlled by going to select Menu > Settings > Display. Select any one of the following options and press Select to save your changes. Brightness to set the brightness of the screen Screen light to set the duration for screen backlights Keypad light to set the duration for keypad backlight Screen standby to set the duration for the screen backlights after the last keystroke Setting the time zone You may wish to change the local time zone on your phone if you move to a new location or if your new phone is not displaying the correct time zone. You may also wish to know the time in another location, eg. your head office. Setting the local time zone Select Menu > Extras > World time. The world time map appears. Select Options > Select > Local time zone. Use the navigation keys to highlight the required time zone and press Select. Setting the remote time zone Select Menu > Extras > World time. Select Options >

Select remote time zone. Use the navigation keys to highlight the required time zone and press Select. Setting daylight saving time (DST) Select Menu > Extras > World time. Select Options and select from a list to enable/disable local/remote DST. DST is displayed as 0 or +1 on the world map. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 50 Setting up keypad lock The keypad lock disables the keypad and prevents accidental dialling. When activated, the phone will respond to the green to answer or reject call. and red keys Bluetooth The Bluetooth connection on your phone allows you to connect wirelessly to a Bluetooth headset enabling you to use the phone in handsfree mode. Select Menu > Settings > Security, select Automatic keypad lock, and then select the duration before the keypad is locked. Deactivate the automatic keypad lock using the same menu. To activate Bluetooth connectivity select Menu >

Settings > Bluetooth. Select Settings > Bluetooth and select On. The Bluetooth icon indicator appears in the status bar. To lock the keypad, ensure the main screen is displayed, press the centre selection key followed by the * key within 3 seconds. The keypad locked the status bar. icon is displayed on To unlock the keypad, press the centre selection key followed by the * key on the keypad within 3 seconds. Setting up phone lock Phone lock protects your phone against unauthorised use. Select Menu > Settings > Security and select Phone lock. Specify the idle period, from 30 seconds to 30 minutes, after which time the phone will automatically lock. You will be prompted to Enter phone lock code. To unlock the phone, enter the code when prompted. The default admin code is 123456. See Setting up the admin code on page 54. The new setting will be accepted when the code is accepted. Connecting a new Bluetooth device The first time you use a particular Bluetooth headset with your phone, you will need to pair the phone and the headset. Ensure the Bluetooth headset is switched on before you begin. Select Menu > Settings > Bluetooth > Paired devices. A list of Bluetooth devices in range of your phone will appear on the screen. If the device does not appear, select Options and select Search for devices from the new menu that appears. Searching... will be displayed at the top of the screen, followed by the names of all the devices in range. A blue tick will be displayed next to any devices already paired with your phone. Select the device you want to pair and enter its pass code. Bluetooth devices such as headsets generally have their pass code set in the factory and printed either on the device or its packaging. Some devices allow you to set the pass code yourself. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 51 The device should now be listed in the Paired devices menu. Highlight it and press the left selection key, then select Connect from the menu. The device should now be listed on the Connected devices menu accessed from the Bluetooth menu. This phone is connected with a Bluetooth headset. icon indicates that your Whenever the device attempts to make a connection with your phone, you will be prompted whether you want to accept the connection. To automatically accept connection requests from a particular device, highlight it in the Paired devices menu, select Options and select Set as authorised. You should only authorise devices that belong to you, or that you trust. If you no longer want a device to be authorised, select Set as unauthorised. To connect a different headset, you must disconnect the current headset. Highlight the device on the Connected devices menu, select Options and select Disconnect. If you no longer want a headset to be paired with your phone, highlight it on the Paired devices menu, select Options and then select Delete. Other choices in the Options menu are Rename, which allows you to select a more descriptive name for your headset, and Device attribute, which displays the headsets name, and the time and date at which it was connected. When you are not using Bluetooth connectivity, select Bluetooth > Off or My phones visibility > Invisible. This prevents unauthorised connection. Do not pair with an unknown device. Setting up Bluetooth lock If Bluetooth lock is enabled, the phone will require the admin code to be entered before Bluetooth settings can be changed. See Setting up the admin code on page 54 for more information. The default setting is off. To enable or disable this feature, select Menu > Settings

> Security and select Bluetooth lock from the list. Select On or Off and then enter Admin code. Operating a Closed User Group

(CUG) The Closed User Group (CUG) service allows you to form closed user groups from which access is restricted. A user may be a member of one or more CUGs. Members of a specific CUG can communicate amongst themselves but not, in general, with users outside the group. This feature is operated by your service provider who will provide further instructions on its use. The default setting is off. To enable, select Menu > Settings > Security >

Closed user group, select On, enter your CUG number and press OK. Group numbers range from 0-9. If the CUG is on, the CUG index icon appears on the status bar. Reset all settings Select Menu > Settings > Reset settings. You will be prompted for the Admin code in order to make this change. See Setting up admin code on page 54 for more information. Returning to default settings will not affect your admin or user codes, PINs, organiser entries, contacts, messages or call logs. To return these to default setting or to delete these entries see:

Setting up SIM PIN code on page 55 Setting up SIM PIN 2 code on page 55 Deleting a contact on page 42 Deleting SIM contacts on page 43 Deleting messages on page 32 Deleting all call logs on page 23 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 52 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 53 Security locks and codes SECURITY FEATURES CONTROLLED BY ACTION DEFAULT SETTING DEFAULT CODE CODE LENGTH The Phone Keypad lock Admin code Only the green and red keys are active Creates Phone lock Restricts access to Bluetooth Restricts access to Reset settings Restricts access to Personal alert Creates User code The SIM card PIN PIN 2 The network Barring password Restricts access to SIM card Rest Restricts access to Fixed number dialling Restricts access to Call barring Centre selection key and *

123456 6 digits 4-6 digits 8888 9999 4-8 digits 4-8 digits 0000 4 digits Off Off Off Off Off SECURITY Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 54 Security can be controlled by the phone, the SIM card or the Inmarsat network. This enables you to match security requirements to your needs. The keypad lock prevents accidental dialling; the phone lock prevents an unauthorised user from using your phone even if they replace the SIM card. The SIM PIN prevents an unauthorised user from using your SIM even if they place it in another phone. The admin code restricts access to particular features on the phone. For example, an individual might only wish to activate the keypad lock. A corporate organisation might choose to restrict functions available to their employees by activating the admin code and issuing a user code. Security features controlled by the phone Access to your phone can be restricted by the keypad lock to prevent accidental dialling (see Setting up keypad lock on page 50 for more information) or by activation of the admin code. The admin code can be activated: to create a Phone lock; restrict access to Bluetooth lock, Personal alert lock and Reset settings; and to create a User code so that a third party can use the phone but not have access to the restricted features. See Setting up Bluetooth lock on page 50 and Reset all settings on page 52 for more information. Setting up the admin code Select Menu > Settings > Security and select Admin code. You will be prompted for the current code. The default setting is 123456. When this is accepted, you will be prompted to enter your new code and then confirm it. The code must be 6 digits long. If you lose your admin code, contact your service provider. The default setting is off. The admin code can be entered incorrectly an unlimited number of times. If you have forgotten your code, contact your service provider. Setting up the user code Select Menu > Settings > Security and select User code. You will be prompted to enter the 6-digit Admin code. Once this is accepted, you will be prompted to create a new user code and to confirm it. The code can be 4-6 digits in length. The default setting is off. The user code can be entered incorrectly an unlimited number of times. If you have forgotten your code, contact your phones administrator. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 55 Security features controlled by the SIM card Access to your SIM card can be restricted by activating its PIN code. The advanced call feature, Fixed number dialling, can be protected by your SIM PIN 2 code. See Fixed number dialling on page 26 for more information. Setting up SIM PIN code Select Menu > Settings > Security > PIN request and select On. You will be asked to enter your SIMs PIN code. If you make an error entering the number, press Cancel to clear the digits and re-enter. Press the centre selection key or OK. The default 4-8 digit code for SIM PIN is 8888. The default setting is off. To change the PIN code stored on your SIM card, select Menu > Settings > Security > Set PIN. Enter the existing PIN code, then the new PIN. Repeat the new PIN to confirm it. If the PIN code is entered incorrectly three times, your SIM card can only be unlocked using the PUK code. Contact your service provider if you do not have a record of your PUK code. If the PUK code is entered 10 times incorrectly the SIM will lock and you should contact your service provider. The default setting for PIN is off. Setting up SIM PIN 2 code The default 4-8 digit code for PIN 2 is 9999. The default setting is off. If the PIN 2 code is entered incorrectly three times, your SIM card can only be unlocked using the PUK 2 code. Contact your service provider if you do not have a record of your PUK 2. If the PUK 2 code is entered 10 times incorrectly the SIM will lock and you should contact your service provider. To change the PIN 2 code, select Menu

> Settings > Security > Set PIN 2. Enter the existing PIN 2 code, then the new PIN 2 code. Repeat the new PIN 2 code to confirm it. Security features controlled by the network When enabled, the advanced call feature, Call barring, is protected by a code. The default setting is off. See Call barring on page 24 for more information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM SOLUTION My phone will not switch on Check if the battery is inserted correctly Check if the battery needs charging. Charging for 20 minutes should provide enough power to switch the phone on If the battery does not charge it has probably exceeded its usage period and you will need to replace it with a new one My phone cannot make or receive calls Ensure the SIM card is inserted in the phone and is fully provisioned by your service provider Check you have a valid GPS fix (See Using your GPS location information on page 38 for more information) Ensure the phones antenna is fully extended and you have a clear line of sight to the satellite. See Connecting to the satellite on page 14 for more information. A least two signal bars are required to make and receive calls If you have less than two bars signal strength, rotate the phone and angle the antenna until the signal strength increases and you are able to make and receive calls If the phone has sufficient signal strength and cannot make or receive calls, check if Call barring (page 24), Diverting calls (page 25) or Fixed number dialling

(page 26) have been activated If you have a prepay subscription, check your prepay balance to ensure you have sufficient credit to make a call. See Making a balance enquiry on page 34 for more information Contact your service provider if you are unable to resolve the problem 56 Troubleshooting 1 2 3 TROUBLESHOOTING Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM My phone cannot receive a text message My phone continues to display Searching satellite My phone displays a language I do not understand SOLUTION The phone can store a maximum of 20 messages in its memory. If the memory is full, delete a few texts to free up memory for new messages. See Deleting messages on page 32 for more information If you still cannot receive a text, your service centre number may not be correct. See Entering your service centre number on page 33 for more information or contact your service provider Ensure your phones antenna is fully extended Ensure your phones antenna is pointed towards the satellite. Press Help for onscreen guidance. Consult the Coverage map on page 9 to ensure you are within coverage Ensure there is a clear line of sight to the satellite with no obstacles which could block the signal. See Connecting to the satellite on page 14 for more information Contact your service provider if you are unable to resolve the problem Press the red key to return to the main screen Press the left selection key to go to the menu screen Press the down navigation key twice to highlight the Settings icon Press the centre selection key to open Settings Press the down navigation key twice to highlight the Language and press the centre selection key icon Press the centre selection key and use the navigation keys to highlight the correct language and press the centre selection key again to change the phones language 57 Troubleshooting 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM SOLUTION My phone does not display a GPS position Some national policies do not allow users to access their GPS information in particular locations. Your phone continues to access the GPS satellites as usual, but your phone will not display its GPS location My phone does not seem to receive voicemails My phone and/or SIM has been lost or stolen How do I contact my service provider?

Ensure your service provider has enabled voicemail Contact your service provider as soon as possible so your phone and/or SIM can be barred Your service provider number is stored on your SIM card. To view your service provider open Info by pressing the centre selection key and selecting Service provider 58 Troubleshooting 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 59 Caring for your IsatPhone 2W 60 Certifications 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Caring for your IsatPhone 2W Your IsatPhone is a highly sophisticated electronic device. Complying with the following recommendations will help you to protect your warranty coverage and extend your phones life:

Keep your phone dry. Liquids or moisture can contain minerals that will damage electronic circuits. If your phone does get wet, dry it with a soft absorbent cloth as soon as possible, remove the battery and allow your phone and battery to dry completely before replacing it The connector covers are intended to protect your phone. When the connectors are not in use, keep these covers firmly closed at all times. Ensure that the connectors are free from dust or dirt before connecting any accessory. When closing the connector cover, ensure the area around the connectors, and the rubber sealing surfaces of the cover are clean and free from dirt. Ensure that the cover is fully closed to give maximum protection to your phone Do not store your phone in dusty, dirty or damp areas as this may shorten its life Do not store your phone in direct sunlight, or in places where the suns heat can be focused, like on the dashboard of a vehicle Do not store your phone and battery in extreme cold and hot areas exceeding a temperature range of -20C to +70C (-4F to +158F). Extreme temperatures can shorten the life of your phone and damage the battery Your phones operating temperature range is -20C to

+55C (-4F to +131F). The charging temperature range is 0C to +45C (+32F to +113F) If you are carrying a separate battery, keep it inside the plastic bag supplied. Always keep batteries separated from other metallic objects and keep it dry to prevent damage If your phone displays Battery overheating, switch it off and place in a cool area Do not use harsh chemicals, cleaning solvents or strong detergents to clean your phone Do not paint your phone Do not attempt to disassemble your phone or undertake repairs yourself Use only the Inmarsat-supplied or an approved replacement antenna. Unauthorised antennas, modifications or attachments could damage the device and may violate regulations governing radio devices 59 Care and maintenance 1 2 CARE AND MAINTENANCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 59 Caring for your IsatPhone 2W 60 Certifications 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone When using any cable connections with your phone, ensure that it cannot be stepped on, tripped over or otherwise subjected to damage or stress Upgrade your phones firmware when advised to do so by Inmarsat or your service provider These suggestions apply equally to your phone, battery, chargers, and any accessory. If your phone is not working properly, contact your service provider. Certifications Your IsatPhone 2W is certified with an Ingress Protection rating of IP65, which means that your phone is resistant to dust and splashing. Do not store fully charged or low charge batteries for long periods of time without use. 80% charge is optimal for storage. The battery should be stored in dry conditions, not assembled into the handset, with the contacts protected. Ideal conditions are between

-20 and +20 C. Please check the remaining power levels in the battery and test the handset every three months. Recharge if the power has dropped below 40%. More frequent checking and recharging may be necessary depending on storage conditions. When the battery charge is very low, it may take some time for the charging indicator to show on the screen after connecting the charger. To view the battery % charge remaining, please look in Settings > About. Unplug the charger from the power socket and your phone when not in use. Do not leave a fully-charged battery connected to a charger, as overcharging may shorten its life. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Batteries gradually lose their charge even when the phone is completely switched off. When the talk and standby times are noticeably shorter than normal, replace the battery 60 Care and maintenance 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 61 European declaration of conformity and CE marking Inmarsat Global Limited hereby declares that IsatPhone 2W is in conformity with the essential requirements and other relevant provisions of the Radio Equipment Directive

(2014/53/EU) and the Recast Restriction on Hazardous Substances Directive

(2011/65/EU). A copy of the original Declaration of Conformity can be found at:

inmarsat.com/isatphone. Hersham Place Technology Park, Molesey Road, Hersham, Walton-on-Thames, Surrey, KT12 4RZ, United Kingdom. BABT IsatPhone 2W is in conformity with the following standards and/or normative documents:

Health and Safety: IEC 60950-1:2005 + AMD1:2009 + AMD2:2013, IEC 62368-1:2014, EN 50360:2001. EMC: EN 301 489-1 V2.1.1 (2016-11), EN 301 489-3 V2.1.0 (2016-09), EN 301 489-17 V3.1.1 (2016-11), EN 301 489-20 V1.2.1 (2002-11), EN 55032:2015. Spectrum: EN 301 681 V2.1.2 (2016-11), EN 303 413 V1.1.1 (2017-06), EN 300 328 V2.1.1 (2016-11). The technical files relevant to the above declaration are held at Inmarsat Global Limited, 99 City Road, London EC1Y 1AX, United Kingdom. REGULATORY AND COMPLIANCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 62 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC caution: Under 47 CFR 15.21, changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. GMPCS IsatPhone 2W carries the International Telecommunication Union (ITU) Global Mobile Personal Communications by Satellite (GMPCS)-MoU mark. Industry Canada This Class B digital apparatus complies with Canadian ICES-003, CAN ICES-3 (B)/NMB-3(B). FCC Part 15 declaration IsatPhone 2W complies with Part 15 of the FCC Rules and, as such, operation is subject to the following two conditions:

1 This device may not cause harmful interference, and 2 This device must accept any interference received, operation including interference that may cause undesired Note: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference as follows:

Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area Directive 2012/19/EU regulates the disposal of electrical and electronic equipment in the EU and Directive 2006/66/EC regulates the manufacture and disposal of batteries in the EU. Inmarsat intends to join an EU certified Producer Compliance Scheme (PCS) to meet its obligations as a producer under these Directives. Electronic equipment and batteries should not be included as household waste but should be left at an appropriate collection point for recycling. This helps prevent potential negative consequences for the environment and human health. Check local regulations by contacting your local city office, your household waste disposal service, the vendor of your phone or calling Inmarsats or your local service providers call centre. Do not attempt to remove internal batteries. Internal batteries shall be removed only by a waste treatment facility or trained service professional. The crossed out wheeled-bin symbol on IsatPhone 2W and its rechargeable battery reminds you that all electrical and electronic products and batteries must be taken to separate collections at the end of their working life. This applies to the EU and other locations where separate collection systems are available. Please note that lithium ion batteries meet the definition of dangerous goods in international transport legislation and therefore customers must check with the relevant postal operator before posting any batteries. RoHS compliance IsatPhone 2W complies with the EC Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment 2011/65/EU (RoHS Recast). REACH Regulations IsatPhone 2W complies with the EC Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals No. 1907/2006 (REACH). This User Guide is published by Inmarsat without any warranty. Except as provided by applicable law and in the IsatPhone 2W end-user Warranty, no warranties of any kind, either express or implied, including, without limitation,the implied warranties of satisfactory quality, merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or completeness of this User Guide. Inmarsat reserves the right to make changes to this User Guide at any time and without prior notice. All illustrations are for illustration only and are not an accurate depiction of an actual IsatPhone 2W. All rights are reserved. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 64 DISCLAIMER Inmarsat provides the following in-box accessories with the IsatPhone 2W:

Battery USB drive Mains charger and four universal plug adaptors Car charger Micro USB cable Wired handsfree headset Wrist strap Holster Inmarsat reserves the right to add or delete accessories from this list at our absolute discretion. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 65 ACCESSORIES IsatPhone 2W and in-box accessories may contain commodities, technology and/or software subject to export controls and regulations imposed by the US and other countries. Diversion contrary to law is prohibited. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 66 EXPORT CONTROLS Malicious software (also commonly referred to as malware) is software that can harm the phone or other computers. Malware or harmful applications can include viruses, worms, spyware, and other unwanted programmes. While the phone does employ security measures to resist such efforts, Inmarsat does not warrant or represent that the phone will be impervious to the introduction of malware. You can, however, reduce the risk of malware attacks by exercising care when downloading content or accepting applications, refraining from opening or responding to messages from unknown sources, using trustworthy services to access the Internet, and only downloading content to IsatPhone 2W from known, reliable sources. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 67 MALWARE IsatPhone 2W has the capability to download, store and forward additional content. The use of such content may be restricted or prohibited by rights of third parties, including but not limited to restriction under applicable copyright laws. You, and not Inmarsat, are entirely responsible for additional content that you download to or forward from your phone. Prior to your use of any additional content, please verify that your intended use is properly licensed or is otherwise authorised. Inmarsat does not guarantee the accuracy, integrity or quality of any additional content or any other third party content. Under no circumstances will Inmarsat be liable in any way for your improper use of additional content or other third party content. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 68 DOWNLOADING CONTENT INMARSAT is a registered trademark of the International Mobile Satellite Organisation; the Inmarsat LOGO is a registered trademark of Inmarsat (IP) Company Limited. Both trademarks are licensed to Inmarsat Global Limited. Bluetooth is a trademark or a registered trademark of Bluetooth SIG Inc. and any use of such mark by Inmarsat is under licence. Microsoft Outlook, Microsoft Outlook Express, Microsoft Windows 7, Microsoft Windows 8, Microsoft Windows Vista SP1, Microsoft Windows XP Pro SP3 are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. Other product and company names mentioned herein may be the trademarks of their respective owners. Copyright Inmarsat Global Limited 2017. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 69 NOTICES The user is advised to erase personal data before disposing of the phone. Deleting data from the phone memory does not ensure that it cannot be recovered. Accordingly, Inmarsat does not warrant against recovery of information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 70 PROTECTION OF PERSONAL INFORMATION Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 71 Specification for product 71 Specification for unit Index 72 71 Specification for product MANUFACTURER PRODUCT TYPE / MODEL SPECIFICATION Battery Charger Inmarsat Phihong 56426 702 098 3.7 V, 3180 mAh, 12 Wh, Li-ion PSM10R-050 Input = 100~240 V, 50/60 Hz, ~0.5A Output = 5 Vdc, 2 A MAX Car charger Tenwei Electronics Car adaptor Input = 10-30 Vdc Output = 5 Vdc, 1.2 A Specification for unit UNIT SPECIFICATION Voltage Current Operating temperature Charging temperature Nominal battery voltage 3.7 V/900 mA 900 mA

-20C to +55C (-4F to +131F) 0C to +45C (+32F to +113F) TYPE AND SPECIFICATION Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 72 A Accessories Admin code Alarm Cancelling Setting Silencing Any key answer Assistance button Activating an assistance button alert Assistance button security Configuring assistance button calls Configuring assistance button messages Enabling assistance button calling B Balance enquiry Barring calls Battery Charging Inserting Low battery alert Removing Bluetooth Connecting Lock Security Business card C Caller ID Sending Calls Barring Conference Declining Delete call logs Diverting Emergency From contacts From received message Handsfree Length Muting a call Receiving a call Receiving a second call Returning Summary Volume control While on another call Call waiting Setting Using Charger Car Mains Solar USB 65 54 44 44 44 23 36 36 35 35 35 34 24 11 10 11 10 50 51 51 43 24 24 19 17 23 25 19 16 31 21 22 21 17 18 17 23 21 17 24 18 11 11 11 11 INDEX Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 73 Closed user group Operating Code Admin PUK PUK 2 SIM PIN SIM PIN 2 User Conference calling Contact Calling a contact Creating Deleting Deleting all Duplicating Editing Emailing Finding Opening Ordering by first or last name Texting Copy SIM contacts to Phonebook CUG D Data Date and time settings Daylight saving time (DST) Disclaimer Display Customise settings Diverting Calls E eCompass function Finding a satellite Improving signal strength Emergency calling Export controls F Firmware version Fixed number dialling Activating De-activating Using G GPS Displaying in imperial Displaying in metric Fix National policies Obtaining a manual fix Satellite Sending your location Viewing your location Groups Add Assign ringtone Belongs to Members Remove Sending texts to View 51 54 55 55 55 55 54 19 42 41 42 42 42 42 42 41 41 41 42 43 51 45 48 49 64 49 25 15 15 19 66 13 26 26 26 39 39 15 39 39 14 39 38 32 32 32 32 32 32 32 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 74 H Handsfree calling I IMEI number IMSI number Incoming call alerting Configuring the incoming call alerting feature Missed incoming call alerts Receiving an incoming call alert Using incoming call alerting Info Important information IsatPhone Caring for K Keypad Changing Light Locking Volume L Language Phone Writing Local time zone setting Lock Bluetooth Keypad Phone Loud profile Loudspeaker M Mains charger Map Members Groups Messages Concatenation Create new Creating text for sending to email Delete Expiry period Forward Groups Receive Reply Service centre number Setting Validity Viewing received messages Message service centre number Microsoft Outlook Microsoft Outlook Express Minute counter Model My phone number N Number Re-dial Service provider Your phone number 21 12 12 21 20 20 20 12 59 48 49 50 46 47 48 49 51 50 50 46 21 11 8 32 33 29 30 32 33 31 32 30 31 33 33 33 31 33 9 9 22 12 44 17 44 44 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 75 P Pass code Call barring Personal alert Sending a personal alert Setting up and activating a personal alert Personalising settings Phone Language Lock Off On Upgrade Phonebook Managing contacts Phone language Setting Predictive text Setting Prepay Balance enquiry Voucher redemption Profiles General Loud Silent Vibrate only PUK 2 code PUK code R Received messages Save details Save message Re-dial Auto Remote time zone setting Reset all settings Ring mode Ringtones Assign to groups Unique S Satellite Screen Brightness Light Lighting Standby Security Admin code Network-controlled Phone-controlled SIM card-controlled SIM PIN 2 code SIM PIN code User code Service provider SIM card Copying Inserting Subscription SIM contacts Copying SIM PIN 2 code SIM PIN code 24 40 39 46 12 50 12 12 13 41 47 48 34 34 46 46 46 46 55 55 31 31 17 49 52 46 32 47 14 49 49 49 49 54 55 54 55 55 55 54 44 43 10 9 43 55 55 U User code V Vibrate only Voicemail Voucher redemption W World time Wrist strap Writing language 54 46 22 34 49 12 48 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 76 Solar charger Sounds Ringtones Specification and type Speed dialling Removing Setting up Using T Texts Entering Predictive text Selecting standard or predictive mode Sending to group Standard text Time Daylight saving Time zone Local Remote Setting Tracking 11 46 71 23 23 23 28 28 29 32 29 49 49 49 49 Choosing the message interval 38 Choosing the message recipients and message type 37 37 Configuring tracking Starting tracking 38 38 Stopping tracking 37 Tracking feature Tracking security 38 56 71 Troubleshooting Type and specification Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2W 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 77 inmarsat.com/isatphone While the information in this User Guide has been prepared in good faith, no representation or warranty, express or implied, is made or given as to the adequacy, accuracy, reliability or completeness of such information. Inmarsat Global Limited nor any group company or their respective officers, employees or agents shall have any responsibility or liability to any person resulting from the use of the information in this User Guide. Copyright Inmarsat Global Limited 2017. All rights reserved. INMARSAT is a registered trademark of the International Mobile Satellite Organisation;

the Inmarsat LOGO is a registered trademark of Inmarsat (IP) Company Limited. Both trademarks are licensed to Inmarsat Global Limited. IsatPhone 2W UG August 2017.

Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 1 inmarsat.com/isatphone Congratulations on buying your IsatPhone 2. The satellite phone that delivers:

Dependable connectivity High quality voice Rugged design Assistance button, call alerts and tracking Extended battery capacity From the worlds leading provider of mobile satellite communications Please follow this user guide for further information on how to set up, connect, personalise and use your phone safely. Further information is available at inmarsat.com/isatphone. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Exposure to radio frequency energy IsatPhone 2 is a radio transmitter and receiver. When the phone or Bluetooth handsfree is turned on, it emits low levels of radio frequency energy. The phone is designed and manufactured not to exceed the safety limits for exposure to radio frequencies (RF) as recommended by the ICNIRP (International Commission on Non-Ionising Radiation Protection) and as adopted within mandatory standards of the European Commission and the United States of America. Specific Absorption Rate (SAR) is used to measure radio frequency energy absorbed by the body when using a mobile phone. IsatPhone 2 is compliant with the EC standards for exposure specified in EN 50360:2017 in accordance with EN 62209-1:2016. For use of the phone at the ear, these standards set a SAR limit of 2.0 W/kg averaged over a 10g volume. IsatPhone 2 is also compliant with the Federal Communications Commission (FCC) standards and test procedures as reflected in the requirements of 47 CFR 2.1093 in accordance with KDB 447498 D01 v06, and of ISED RSS-102 in accordance with Health Canada Safety Code 6. For use of the phone at the ear, these standards set a SAR limit of 1.6 W/kg averaged over a 1g volume. Tests for SAR are conducted in accordance with international guidelines for testing using standard operating positions as per the procedures for the applicable standards, with the device transmitting at the highest certified power levels in all operational frequency bands. Note: The SAR requirements for IsatPhone 2 are met for radiating operation whilst handheld at the ear. No measures have been taken for SAR compliance when radiating in a body-mounted position. Hence, radiating operation of the IsatPhone 2 is not recommended when in a body-mounted position. It should be noted that the IsatPhone 2 is not capable of radiating when the antenna is in the stowed position. Hence, when operating in incoming call alerting mode

(see page 20) with the antenna stowed, (either with or without the handset in the holster), the handset cannot radiate and may be body-mounted without posing a safety/health risk. Pacemakers Wireless phones may adversely affect the operation of some implanted cardiac pacemakers and other medically implanted equipment. Pacemaker patients should be aware that the use of an IsatPhone 2 in close proximity to a pacemaker might cause the device to malfunction. If a minimum distance of 15cm is kept between an IsatPhone 2 and a pacemaker, the risk of interference is limited. If you have any reason to suspect interference is occurring, immediately switch off your IsatPhone 2. Contact your cardiologist for more information. 3 Safety 1 2 3 SAFETY Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Hearing aids Battery safety Although most modern hearing aids are immune to radio frequency interference from satellite terminals, some wireless devices may interfere with some hearing aids. In the event of such interference from the use of the IsatPhone 2, maintain additional separation between you and your IsatPhone 2 and/or consult with your doctor or audiologist. Other medical devices Although most modern electronic medical equipment in hospitals and other clinical environments is shielded from RF energy, there is still a risk that a wireless device could cause interference. As such, never use your IsatPhone 2 near electronic medical equipment without first requesting permission. Blasting areas and potentially explosive environments As with any wireless phone, do not use your IsatPhone 2 where blasting work is in progress. Observe all restrictions and follow any regulations or rules. Do not use your IsatPhone 2 in areas with a potentially explosive atmosphere. Note that such areas are often, but not always, clearly marked. Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone. Use of batteries that are not Inmarsat-supplied or approved may pose increased safety risks. Do not dispose of batteries in a fire, as they may explode. See Care and maintenance on page 59, and for guidance on the disposal of batteries and electronic equipment, see page 63. Batteries may burn or explode if damaged. Do not dismantle, open, bend or cut cells or batteries. Do not attempt to modify or remanufacture the battery. Do not immerse or expose the battery to water or other liquids. In the event of a battery leak, avoid contact of contents with skin or eyes. If this does happen, flush the affected areas with water and seek medical help as appropriate. Children Keep out of the reach of children. Do not allow children to play with your phone or accessories. They could hurt themselves or others. Products may contain small parts that could become detached and create a choking hazard. 4 Safety 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Driving Loudness warning Only use IsatPhone 2 in a vehicle using an Inmarsat-

approved vehicular docking unit. Check with the vehicle manufacturer to be sure that your phone or Bluetooth will not affect the electronic systems in the vehicle. Full attention should be given to driving at all times and local laws and regulations restricting the use of electronic and wireless devices while driving must be observed. Avoid volume levels that may be harmful to your hearing. Pinch hazard Take care when opening and closing the antenna of your phone, as it may be possible to trap a fingertip. Land use only The IsatPhone 2 is approved for land use only. 5 Safety 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 6 Your IsatPhone Status icons Programmable assistance button Ear piece Ambient light sensor LED tracking indicator LED status indicator Handsfree rest Tracking button Volume up key Volume down key Screen Right selection key Navigation keys Left selection key Call button Centre selection key End button Handsfree rest Keypad Microphone Micro USB port USB/audio protective cover 2.5mm audio connector Strap attachment point LED status indicators Keypad locked GPS fix required Alarm set USB connection Call divert on Conference call activated Unread message Closed user group number Message sent New voicemail Microphone muted Missed call Loud profile active Loudspeaker activated Vibrate profile active Silent profile active Phone memory full Message memory full Bluetooth is paired SIM card memory full Bluetooth headset connected to your phone Wired handsfree headset connected Bluetooth on Assistance button activated QUICK REFERENCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Menu MESSAGING CONTACTS CALL LOG Missed calls Received calls Dialled calls Call duration Phonebook SIM contacts FND list My phone number Service provider Emergency numbers Voicemail number Groups LOCATION SERVICES ALARM Assistance button Tracking Send GPS Personal alert Once alarm Recurrent alarm GPS POSITION NETWORK GPS location Date and time Docking mode About Reset settings Satellite search Advanced options Network operator New message Inbox Outbox Drafts Sent Saved Templates SIM messages PROFILES General Silent Loud Vibrate only SETTINGS Call settings Security Language Display Prepay Bluetooth 7 User Guide instructions commence from the main screen. The red key will take you to the main screen. Click to navigate 2 Welcome 3 Safety 6 Quick reference 6 Your IsatPhone 6 Status icons 7 Menu 8 Coverage map 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 8 Coverage map I-4 Americas Alphasat I-4 Asia-Pacific IsatPhone 2 operates globally over the Inmarsat-4 satellites and Alphasat. This map is illustrative of IsatPhone 2 coverage. It does not provide a guarantee of the extent of service availability. From November 2013, Alphasat coverage prioritises the region north of 44S, and service may degrade south of this latitude. This coverage map applies to both IsatPhone Pro and IsatPhone 2. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 9 Package contents Your IsatPhone 2 box contains:

Phone Battery USB drive Quick Start Guide Warranty Mains charger and four universal plug adaptors Car charger Micro USB cable Wired handsfree headset Wrist strap Holster The USB drive can be accessed by a PC running Windows 10, 8, 7 or XP and contains the following documents:

Quick Start Guide User Guide Warranty The USB drive also contains the following applications and related How to guides:

USB Drivers: for charging your phone via a PC, setting up a software modem and for running Contact Synchronisation and Firmware Upgrade tools Contact Synchronisation Tool: for synchronising your phone with Microsoft Outlook and Microsoft Outlook Express contacts Firmware Upgrade Tool: for undertaking future upgrades The above documents and applications are available in English, Spanish, French, Japanese, Portuguese, Russian, Chinese and Arabic. They can also be downloaded from inmarsat.com/isatphone Setting up your IsatPhone Subscriptions and SIM cards To use your phone, you will need a SIM card and a subscription. The services available to you may depend on your choice of subscription. Contact your service provider for details. Setting up your IsatPhone 1 2 3 GETTING STARTED Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 10 Inserting and removing the battery Your phone is supplied with a rechargeable battery, which may not be fully charged when you take it out of the box. Always switch the device off and disconnect the charger before removing the battery. See Care and maintenance on page 59 for more information. Inserting the SIM card Your service provider may have inserted your SIM for you. If not, your phone will prompt you to Insert SIM and offer only a limited service until you do so. 1 Remove the battery by pressing the catch and lifting the battery up and out of the phone 2 Insert the battery by pressing the battery forward and down. It will click into place 1 If the battery is in place, lift it out 2 Slide the catch down on the SIM holder and flip it outwards 3 Make sure the angled corner of your SIM card is on your left and slide it into the holder 4 Flip the holder back into place and slide the catch back up 5 Insert the battery Setting up your IsatPhone 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 11 Charging the phone battery Your phone is powered by a rechargeable lithium-ion battery. To maximise its life and its charging capacity, the first time you charge the battery, charge it overnight. Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone. Do not leave the battery charging for extended periods of time. The battery can be charged by:

Using the AC charger (connecting to a wall socket) Using the micro USB cable (connecting to a PC) Using the car charger (connecting to a vehicle cigarette lighter/power outlet) Using the docking station You also have the option of using a solar charger. Contact your service provider for details. Connect the charger to a power source and the micro USB connector to the port at the base of the phone, under the USB/audio protective cover. When the battery needs charging, the low battery alert sounds and a Battery low message is displayed. The phone will automatically switch off shortly afterwards. You might be able to switch the phone on again, but you cannot make or receive any calls until the battery has been recharged or replaced. Use the Docking Mode option, on the Settings menu, to control battery recharging. The default setting is Off (full charge) this will continually charge your battery to 100% until your phone is removed from the charger or docking station. Select On (limited charge) to select a level at which recharging will be triggered. The Frequent docking option will start charging your battery when the charge drops to 80%

The Permanent docking option will start charging your battery when the charge drops to 20%

Note: If your phone is connected to a charger or docking station for long periods of time, you can use the docking mode settings to ensure that your phone only charges when necessary. This will prolong your battery life and conserve power. Setting up your IsatPhone 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 12 Attaching the wrist strap Your phone is supplied with a wrist strap. To connect the strap, remove the battery cover. Thread the small loop through the entry point at the base of the phone. Loop it over the anchor point to secure it and replace the battery cover. Switching your phone on and off To switch on, hold down the red key for a few seconds until the screen lights up. The Inmarsat logo will appear followed by the main screen. To switch off, press and hold the red key for a few seconds. Note: If you see the message Insert SIM, you must insert a SIM card to use your phone. You will also be prompted to enter the PIN code if one is set. The default setting for the PIN code is off. See Setting up SIM PIN code on page 55 for more information. Until a SIM card is inserted, only a limited service is available. See Making an emergency call on page 19 for more information. Setting the phone language and time zone The first time you turn on your phone, you will be prompted to select your language. This will be the display language. Select your language from a list using the navigation keys and the centre selection key. See Setting phone language on page 46 for more information. After you have selected your language, you will be prompted to select your time zone. Your phone automatically receives universal time (UTC) from GPS satellites. By selecting the time zone, the phones clock will display your local time. If you move into another time zone, you will need to change this setting. See Setting the time and Setting the time zone on page 49 for more information. Using info Important information about the status of your phone is displayed in the information shortcut Info on the main screen. These include missed calls, new messages, voicemails, todays organiser appointments, active profile status, your phone number and your service providers number. Info will pop up on the main screen if you have missed a call or have new messages or voicemails waiting. To access Info at other times, press the centre selection key. When Info is open, use the navigation keys to highlight the information you wish to access and press the centre selection key to open. Accessing important information about your phone Important information about your phone is displayed under Menu > Settings > About. These include your model, firmware version, IMEI number and IMSI number. You may need to supply this information when contacting your service provider. Upgrading your phone From time to time it may be necessary to upgrade your phones software in order to improve its functionality and operation. Inmarsat or your service provider will contact you if your phone needs upgrading. Run the USB drive supplied with your phone to download the Firmware Upgrade Tool. The guide How to Upgrade your IsatPhone is available on the USB drive, and can also be downloaded from inmarsat.com/support/isatphone-2-support/

Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 9 Package contents 9 Setting up your IsatPhone 12 Attaching the wrist strap 12 Switching your phone on and off 12 Setting the phone language and time zone 12 Using info 12 Accessing important information about your phone 13 Upgrading your phone 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 13 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 14 Your IsatPhone makes and receives calls by communicating with Inmarsat satellites in orbit above the equator. Your phone antenna must be deployed and there must be a clear line of sight to an Inmarsat satellite for you to make and receive calls. Connecting to the satellite Switch your phone on, hold down the red key few seconds until the screen lights up. The Inmarsat logo will appear followed by the main screen. for a If prompted to enter a PIN, enter the PIN code. The PIN is originally set by your service provider which you can reset. See Setting up SIM PIN code on page 55 for more information. Stand outside with a clear view of the sky with the phone antenna pointing upwards. There must be a clear line of sight between the phones antenna and the satellite. The more sky you can see the stronger the signal should be from the satellite. If open sky makes up about 70%

of your view when you look up, then the signal should be strong. Searching satellite will appear on the screen. When your phone is connected to the satellite, the screen will display Ready for service. The top left of the screen will display Inmarsat. The signal bars indicate the signal strength. At least two signal bars are required to make and receive calls. USING YOUR ISATPHONE 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 15 Using the eCompass function In order to connect to the network, the handset needs to acquire a GPS fix. This happens automatically. If you are unable to obtain a GPS fix, or your fix is out of date, your search will fail and a red circular icon will be displayed in the status bar on screen. The handset will display information to assist you in acquiring a GPS fix. To maximise your chances of obtaining a GPS fix as quickly as possible, stand outside with a clear view of the sky. Finding a satellite If the handset is unable to register to the network, or if the received signal strength falls during a call, the eCompass function is automatically displayed on-screen. It helps by showing the direction towards the best Inmarsat satellite. In response, you must point the antenna until the on-

screen satellite image turns green. You need to ensure that, in the direction indicated, there is clear line of sight to the sky and no obstructions. The eCompass is never displayed while the handset is correctly connected to the network. When it appears, turn towards the satellite in the direction indicated. The on-screen satellite image changes to green to show that you are pointing the handset in the correct direction. Then press Search. Improving signal strength If the received signal strength falls during a call, as shown by the signal strength indicator, ensure that the antenna is pointed towards the satellite and there are no obstacles between you and the sky. The eCompass is displayed to indicate the direction in which the antenna should be maintained. When you return the handset to your ear, ensure that you keep it pointed in the direction of the satellite. Obtaining a GPS fix Before you can make a call, your phone needs a GPS fix so it can be located by the satellite. This happens automatically but if a new GPS fix is needed, the GPS fix the open with a clear view of the sky until the disappears. Your phone is now ready to make and receive calls. See Obtaining a GPS fix manually on page 39 for more information. icon will be displayed. Keep the phone in icon Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 16 Making and Receiving calls 1 Switch on your phone by holding down the red key for several seconds. 2 Stand outside with a clear view of the sky and the antenna pointing upwards. 3 Check your phone is connected to the satellite network - Inmarsat is displayed at the top left of the screen. 4 Ensure you have at least two bars of signal strength. 5 Ensure there is sufficient battery power. 6 Ensure that your phone has a GPS fix the GPS fix required icon is not displayed. 7 Dial the full international number and press the green key, eg. +44 1621 123456

. 8 To end a call, press the red key

. 9 Switch off your phone by holding down the red key until the screen shuts down. Making a call Enter the full international number by dialling either +

(hold down the 0 key for 3 seconds) or 00, country code, area code (without the leading 0), telephone number and

, eg. 00 44 1621 123456 press the green key

+ 44 1621 123456

. A Calling message and the name of the person being called (if listed in your Phonebook or SIM contacts) will display on the screen. When the call is answered, the screen will show the call time in minutes and seconds. To end the call press the red key or

. Making a call from saved contacts Select Menu > Contacts > Phonebook. Scroll to the desired name using the navigation keys, or enter the first letter of the name in the search field. The matching contacts will be listed. Highlight the name and press the

. See Phonebook and Contacts on page 41 green key for more information. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 17

, select from the list of previously Re-dialling a number Press the green key dialled numbers using the navigation keys and press to start the call. Your phone stores 30 the green key dialled numbers. Alternatively, select Menu > Call log >

Dialled calls, select the person you wish to call and press the green key

. Re-dialling automatically To switch Auto re-dial on or off, select Menu > Settings >

Call settings > Auto re-dial and make your selection. The default setting is off. When activated, if your call did not complete, your phone displays Retry? and the reason why the connection was unsuccessful. Press Select to automatically re-dial the number three times until the call is answered. If you press any key or receive a call during this time, re-dialling is interrupted. If the re-dial is successful the phone beeps, then rings. Select Close if you do not want to retry. Receiving a call To receive a call, your antenna must be deployed and your phone connected to the satellite. Press the green key it. You will see Call from followed by either the name of the caller (if listed in your Phonebook or SIM contacts), the calling number, or Number unknown. to accept the call or press the red key to reject If you do not wish your phone to play a ringtone, set your active profile to silent or vibrate only. See Sounds, ringtones and profiles on page 46 for more information. To mute the ringing tone when a call comes in, press Silence. Declining a call

. The call is disconnected and the Press the red key caller details are stored in Missed calls for later retrieval. Returning a call Your phone automatically stores the numbers of the last 20 phone calls you have answered or missed. To return a call, select Menu > Call log. Select the appropriate folder, eg. Missed calls or Received calls, highlight the contact and press the green key

. Making a call while on another call You can put your current call on hold and make a second call at any time. Select the contact by selecting Options >

Contacts > Phonebook or by dialling the full international number. When you press the green key

, your current call will automatically be put on hold. By selecting Swap you can switch between calls at any time. You can end either call at any time by selecting Options > End held call or End active call. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 18 Receiving a second call while on a call The incoming call will be diverted to your voicemail unless you have set up Call waiting. See Setting up call waiting on page 24 for more information. Using call waiting When Call waiting is activated, a pop-up and an audible alert will notify you if another caller is calling you when you are on another call. When you receive this alert you can press the green key to accept the second call. The first call is placed on hold automatically while the second call is taken. By selecting Options > Swap you can switch between calls at any time. You can end either call at anytime by selecting Options >

End held call or End active call. If you receive a third call while you have one active and one held call, the name or number of the caller will be displayed. Ending either the active or the held call will automatically answer the new call. If you wish to disconnect the first call to accept the second, select Options > End active call. The call is disconnected and the caller details If you do not wish to accept the second call, press the red key are stored in Missed calls and Info for later retrieval. If you do nothing, the second caller will be diverted to your voicemail. If voicemail has not been activated, then the call will appear as a missed call. See Setting up call waiting on page 24 for more information. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 19 Making an emergency call Wireless phones, including IsatPhone 2, operate using radio signals, wireless networks, landline networks, and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never rely solely on any wireless device for essential communications like medical emergencies. Emergency calling requirements for satellite phones vary from country to country. Always check your emergency contact numbers and ensure they are stored on your phone before travelling. Please contact your service provider for specific country information. To make an emergency call in the US, dial 911 or 112 and in Australia dial 000 or 112. Your call will be put through to a call centre which will connect you to the appropriate emergency service. Alternatively, select Menu > Contacts

> Emergency numbers. An emergency call is free of charge. Prepay users do not need a positive balance to make an emergency call. Dialling 911 or 112 overides all security locks and bars on your phone. For details on emergency calling in the rest of the world, please contact your service provider. Making conference calls Your phone can host conference calls with up to five participants. To initiate a conference call, call the first participant. When the first participant is connected, call the second participant by selecting Options > Contacts

> Phonebook, select the second participants name and press the green key

. When the second participant is connected, select Options > Conference. You are now in a three-way conference call. Repeat for more participants. To end a conference call, select End or press the red key

. To answer a new inbound call, press the green key or select Options > Answer. The conference call will be placed on hold. To place all participants into one call, select Options > Conference. To place an inbound call into conference without answering it first, select Options > Add waiting to conference. To disconnect individual conference callers, select Options

> Disconnect caller and press Select, or the centre selection key. A list of the participants is displayed. Select by highlighting their name or number and press Select, or the centre selection key, to disconnect them from the call. To speak privately to one participant during a conference call, select Options > Private with a caller and select from the list. To resume the call with all participants, select Options > Conference. To put individual participants of a conference call on hold, select Options > Hold conference party and choose from the list of current callers displayed. Making and Receiving calls 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 20 Incoming call alerting To make or receive calls and messages with any satellite handset, you must maintain a clear line of sight between the antenna of your handset and the satellite. The Incoming call alerting feature notifies you of calls and text messages when satellite signal reception is limited and/or when the antenna is not deployed. Access to the service is still affected by the location of the handset, and is not available when out of the line of sight of the satellite. See Connecting to the satellite on page 14 for normal operation. Using Incoming call alerting Before using Incoming call alerting, each time you switch on the handset it must be successfully registered to the network. To do this, deploy the antenna in a location that has a clear line of sight to the satellite. When the handset is registered, the screen displays Ready for service and the two status LEDs change to green. See Connecting to the satellite on page 14. You can now stow the antenna and place the handset in the holster provided or in another convenient location. Unless Incoming call alerting is disabled, the screen displays Ready for service, Incoming call alerts only and the status LEDs change to amber to indicate that the available signal strength is sufficient to notify you of incoming calls or messages. If the received signal strength is too low, the status LEDs turn red and the screen displays the instruction Point antenna towards satellite. Move to a location with a clear line of sight to the satellite and the two status LEDs will change to amber. The handset will continue to search for the network until you reach a position where the signal strength is sufficient to receive incoming call alerts. Receiving an Incoming call alert When you receive an incoming call alert, you must action in order to obtain full connectivity to the network. This means that you must deploy the antenna if it is stowed, and move to a location with a clear line of sight to the satellite. On receiving an incoming call alert, the status LEDs flash amber and the alert tone sounds. See Sounds, ringtones and profiles on page 46. The screen displays Incoming call and Time remaining 15s. The time counts down until you successfully connect to the network. Throughout this period, the incoming call can be rejected by pressing the red key. Missed Incoming call alerts If you reject an incoming call alert or do not successfully connect to the network within 15 seconds, the alert is terminated. The screen then informs you of a missed alert . You must connect to the network to receive more information about the missed call, voicemail or text. See Returning a call on page 17. Missed calls are forwarded to your voicemail if configured to do so. See Using voicemail on page 22. Incoming call alerting 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 21 Calling handsfree You can also use your phone in handsfree mode. Place the phone on its side with the antenna pointing upwards and use loudspeaker or a handsfree headset. Loudspeaker can be activated at any time during the call. To use the wired handsfree headset, connect it to the audio port at the base of the phone, under the protective cover. To use a Bluetooth headset, see page 50 for more information. Configuring the Incoming call alerting feature By default, Incoming call alerting is set to On. To switch this feature off, go to the main menu and choose Settings

> Call settings > Incoming call alerting. Set the status to Off and press Select. To switch the feature on again, at the main menu choose Settings > Call settings >

Incoming call alerting, set the status to On and press Select. By default, Incoming call alerting is set to provide notification of voice calls only, but you can configure the handset to notify you of text messages as well. Go to the main menu and choose Settings > Call settings >

Incoming call alerting, then choose Configure alerts. The screen displays the options Alert for calls only and Alert for calls & messages. For notification of calls and messages, choose the latter option and press Select. Using the volume control The two volume keys on the side of the phone adjust the call volume. Muting a call Select Options > Mute while on a call. To cancel, select Options > Unmute. Using loudspeaker Select Loudspeaker at any time during a call. Incoming call alerting 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 22 Using voicemail You will be able to receive voicemail messages if your service provider has enabled voicemail. Your phone automatically checks for voicemails shortly after it has been switched on and connected to the network. It will also send you voicemails that arrive while you are connected to the network. will If you have a new voicemail, the voicemail icon appear in the status bar at the top of the main screen and in Info. To listen to the message, hold down the key on the keypad for a few seconds and your phone will automatically connect you to your Inmarsat voicemail. Alternatively, you can dial the short code 570 followed by or the full international number 00 870 the green key 772 001 899 or + 870 772 001 899 and the green key

. Follow the spoken instructions. The default language for voicemail is English, but your service provider may have enabled your voicemail in your chosen language. If you wish to change the voicemail language, follow the spoken instructions or contact your service provider. Additional call features Viewing call length Your phone logs the duration of outgoing and incoming and Dialled calls appears, calls. Press the green key which lists the date, time and duration of each call. Use the navigation keys to access Received calls and Missed calls. Alternatively, select Menu > Call log and make your selection. You may find the Call duration log useful for checking the Last dialled call duration, and the total time of Dialled calls. To reset the counter, highlight the value you wish to reset, select Options > Clear and press the left navigation key labelled Select. To reset all counters, select Options > Clear timers. Setting the minute counter Select Menu > Settings > Call settings > Minute counter and select your preferred setting. The default setting is off. When enabled, your phone will beep after every minute of your call. Additional call features 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 23 Setting up call summary Select Menu > Settings > Call settings > Call summary and then use the navigation and centre selection keys to make your selection. The default setting is on. When Call summary is activated, the date, time and duration of the call is displayed. Setting up and using speed dial First, select Menu > Settings > Call settings > Speed dialling and then use the navigation and centre selection keys to make your selection. The default setting is on. Eight speed dial slots are available, from 2-9. Speed dial 1 is reserved for voicemail. From the main screen, press and hold down for a few seconds the number key that you would like to associate with a contact. If the number is not yet assigned, a pop-up will ask if you wish to assign a contact to the key. Select Yes and a list of Phonebook contacts is displayed. Use the navigation keys to highlight the contact and then the contacts details. Press OK to save your selection. Alternatively, select Contacts > Phonebook. Use the navigation keys to highlight the contact name, press the centre selection key to open or select Options > Open. Highlight the number to which you would like to assign the speed dial, eg. Mobile. Select Options and select Assign speed dial. Highlight a speed dial slot marked Unassigned, press the centre selection key to assign the phone number to that speed dial slot. To remove speed dial, follow the instructions above and select Remove speed dial. To speed dial, hold down the appropriate number of the keypad for a few seconds and the phone will automatically dial the number. Setting any key answer Select Menu > Settings > Call settings > Any key answer and select On. The default setting is off. When activated, press any key to answer a call. Deleting all call logs Select Menu > Call Log. Select Options > Clear all. Press Yes to confirm. Additional call features 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 24 Advanced call features Advanced call features are controlled by the Inmarsat network. To check or change these features, the phone must be connected to the satellite with a signal strength of at least two bars. Call barring An IsatPhone 2 SIM card always uses an international number format, + or 00, and the country code, 870. Call barring prevents the following call types from being made or received by your phone:

Sending your caller ID Select Menu > Settings > Call settings > Send my caller ID, then select On, Off or Set by network and press OK. Set by network leaves it to the network to select whether Caller ID is displayed. The default setting is Set by Network. When Send my caller ID is on, your caller ID will be displayed on the recipients phone. If this feature is switched off, your caller ID will be hidden and Withheld displayed in its place. Setting up call waiting Select Menu > Settings > Call settings > Call waiting, and select Activate. There may be a short delay before the network responds. Call waiting activated will appear when the setting has been enabled. The Call waiting default setting is off. From the Call waiting menu you can also select to Check status or Deactivate. To use call waiting, see Using call waiting on page 18 for more information. Outgoing calls: bars all outgoing calls International calls: bars all outgoing calls except to other Inmarsat numbers International except to home: bars all outgoing calls except to other Inmarsat numbers Incoming calls: bars all incoming calls Incoming outside home: bars all incoming calls except from other Inmarsat numbers Note: This feature is not supported in all countries. If you are using a SIM card with local country numbering, the call barring is as described by the menu. The first time you set up call barring, you will need to reset the barring password. Select Menu > Settings > Call settings > Call barring. Select Options and navigate to Change barring pass code. Enter the barring pass code and select OK. The default is 0000. Enter a new four-digit pass code and select OK. Then enter the new pass code again to confirm it. You will need to enter this new pass code whenever you change your call barring settings. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 25 To cancel a bar, highlight that type of call in the Call barring menu, select Options and select Cancel. To cancel all call barring, select Options and select Cancel all barring. To check the status of a call bar, highlight that type of call in the Call barring menu, select Options and select Check status. The barring code can be entered incorrectly an unlimited number of times. If you have forgotten your code, please contact your service provider. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Call barring and Call divert cannot be active at the same time. Diverting calls Select Menu > Settings > Call settings > Call divert. Call divert allows you to forward incoming calls to your voicemail or another phone number:

Only voice calls diverts any voice call to your voicemail or another number Only data calls diverts data calls to another phone number Only fax calls diverts fax calls to another phone number If busy when you are engaged on another call, this option diverts calls either to your voicemail or to another number If no reply this option allows you to select how long your phone should ring (up to 30 seconds) before the call is diverted to your voicemail or another number If out of reach when you are out of reach of a satellite signal this option diverts calls either to your voicemail or to another number If not available diverts all If busy, If no reply and If out of reach calls. If you subsequently assign a divert number for any of these calls, that number will override the If unavailable divert number After making your selection, you will be prompted to enter the phone number or voicemail to which calls are to be diverted. Select Options to select a number from your phonebook. To cancel call divert, highlight that type of call in the Call divert menu, select Options and select Cancel. To cancel all call diverts, select Options and select Cancel all forwarding. To check the status of a call divert, highlight that type of call in the Call divert menu, select Options and select Check status. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Call barring and Call divert cannot be active at the same time. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 26 Fixed number dialling can restrict your phone to a certain prefix, as well as individual phone numbers. To limit outbound calls or text messages to a specific country or range of corporate numbers, create an FND list entry with the international prefix and local prefix you wish to allow, followed by the correct number of remaining digits replaced by question marks. Press the * key twice to enter a question mark. Example: To limit calls to UK landlines, create an FND list entry: +44??????????. Substitute any number in place of the ? symbols while dialling or sending a message. When fixed number dialling is activated, your phone still enables numbers stored in other areas of Contacts to be viewed. Fixed number dialling (FND) When Fixed number dialling is activated, the user is limited to dialling or texting only numbers stored in the FND list. The default setting is off. Activating and de-activating fixed number dialling Select Menu > Settings > Security, highlight Fixed dialling from the list and press the centre selection key. Select On to activate and press the centre selection key or OK. You will be prompted to enter your PIN 2 code. The default PIN 2 is 9999. See Setting up SIM PIN 2 code on page 55 for more information. Contact your service provider if this code was not specified or was reset at purchase. To add a number to your list, select Menu > Contacts >

FND list and press the centre selection key. Press Options and select either New FND contact or Copy from phonebook. You will then be prompted for the PIN 2 code. FND list entries are stored on your SIM card. Only one name and one contact number can be stored for each entry. Advanced call features 1 2 3 4 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 27 Using fixed number dialling Select Menu > Contacts > FND list and the contact. Select Call or Send message from Options. To send email messages when fixed number dialling is activated, the message centre number should be added to the FND list. See Message settings on page 33 for more information on finding your message centre number. Note: Fixed number dialling, Call barring and Call divert does not prevent emergency calling. Messaging Using the message menu Select Menu > Messaging. Select any one of the following options and press the centre selection key or select Options > Open. The functions are:

New message - to create a new message Inbox - to store received messages Outbox - to temporarily store messages waiting to be sent. Messages are placed in Outbox, for example, when your phone is not connected to the network. If sent, messages will be stored in Sent. If unsent, messages will be stored in Drafts Drafts - when a message is written but not ready or able to be sent, the message is saved here Sent - to store the sent messages. If you want your sent messages to be saved, select Menu > Messaging >

Options > Settings > Text msg settings > Saving sent messages and select On Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 28 Saved messages - to store received messages Using predictive text entry Templates - If you regularly send similar messages, you can set up a template. To do this, compose a new message, select Menu > Messaging > New message >

Text message and compose the parts of your message that will not change. Select Options > Save as template. To compose a new text message based on this template, select Menu >

Messaging > Options > Compose from template and then select the template you would like to use. Edit the text, add recipient and then select Options > Send SIM messages - to store messages in SIM memory. A total of 125 messages can be stored in the phone memory. Entering text You need to enter text when composing a message, adding a contact to your phonebook, adding an appointment to your organiser or searching. Your phone offers two types of text entry mode: predictive and standard. Predictive text mode allows you to use less keystrokes to type a word as it uses a built-in dictionary as a time-

saving feature. For example, to type the word hello, you would only use 5 keystrokes (one for each letter of the word). When you type h (number 4 on the keypad) a list appears on the screen. It is not necessary to select the letter h as when you type e (number 3) the dictionary begins to narrow down the words that begin with he. Key number 5 twice to type ll, then number 6 for the letter o. This will result in the dictionary selecting the only known word with these sequential letters, ie. hello. If the dictionary has a number of options for the same keystrokes it will present a list of words. Use the down arrow to scroll to the word you require and press the centre selection key. As always, press the 0 key to create a space between words. If the word you are typing is not in the dictionary, Word not in dictionary appears. Press OK and select Spell word, type the word you want to enter and press Select. The new word is now saved in your dictionary for future use. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 29 You can change the text entry settings whilst composing a message. Click and hold the # key. A pop-up menu offers options to change the language, text editing mode or to add a new word. Note: To change the language of the dictionary used while composing a text message, select Options >

Writing language. Using standard (non-predictive) text entry Standard text entry enables you to key text in manually, letter by letter, without the phone suggesting the word you are attempting to type. To enter text, repeatedly press a number key, 2-9, until the desired character appears. For numbers, hold the key down longer until the number appears. To insert a space, press the 0 key. For symbols such as punctuation marks, press the * key and then use the navigation keys to select from the menu. Press the # key to change text editing and capitalisation. To delete text, place the cursor to the right of the character you wish to delete and select Clear. Move the cursor around the message using the navigation keys to insert or delete text anywhere in the message. Selecting text entry mode The icon at the top right of your screen displays your choice of text entry mode and character case. The default setting is standard text. If you want to change the text entry mode press the # key repeatedly until your chosen mode icon is indicated. The modes are:

Predictive mode all capitalised Predictive mode initial capital only Predictive mode no capitals Standard mode all capitalised Standard mode initial capital only Standard mode no capitals Standard mode numbers only Standard mode symbols only Creating a text message The character limit for a text sent from your phone is approximately 1600 Latin characters or 740 non-Latin characters, ie up to 10 concatenations, including the recipients telephone number. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 30 Select Menu > Messaging > New message > Text message. A blank screen will appear. Compose your message. See Entering text on page 28 for more information. When you have finished, add the recipient(s). If their details are already stored in your Contacts select Options > Add recipient and select the name from the list. Use the left and right navigation keys to move between Phonebook and SIM contacts. If the recipients details are not stored, use the up navigation key to move the cursor to the To: line. Enter the recipients full international number. If you make a mistake, use the left and right navigation keys to move the cursor and Clear to delete a number. When you have finished adding recipients, select Options

> Send or press the centre selection key. If you want to save your message so you can edit or send it later, select Options > Save, or select Options > Exit and confirm that you want to save the text. The message will be saved in the Drafts folder. When you are ready to complete it, select Menu > Messaging > Drafts. Creating a text message for sending to an email address Your phone can also send text messages to email addresses. Instead of displaying your name to the recipient the message will display your details in the following format:

From: your phone number message.inmarsat.com eg. From: 8707764XXXXX message.inmarsat.com The character limit for a text sent from your phone to an email address is approximately 1600 Latin characters or 740 non-Latin characters, ie up to 10 concatenations, including the recipients email address. Select Menu > Messaging > New message > Email message. Compose your message. Recipients can be added from stored contacts by selecting Options > Add recipient. Only entries containing an email address will be displayed. To send your message to an email address which is not stored, use the up navigation key to move the cursor into the To: field and type the address. For symbols such as the

@ sign, press the * key and then use the navigation keys to select from the menu. After entering the address, wait for 5 seconds and the phone will place a ; after the entry, allowing you to enter another address. When you move the cursor away from the To: field or open Options, your phone will check the email addresses entered. If addresses do not follow the format of a valid email address, they will be deleted and an error message displayed. Receiving text and email messages Messages can be received when the antenna is deployed and your phone is connected to the network, even if you are on a call, or when incoming calls are forwarded to another phone number. If your phone is switched off when a message is received, the message is stored by the network until your phone is switched on and registered with the network. Delivery will be attempted for the duration that your message Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 31 remains in the network. To check or change this setting, select Menu > Messaging > Options > Settings > Text msg settings > Validity period. When you receive a message on your phone, an unread message will appear on the status bar. Info will pop-up and display a list of unread messages. If you wish to read the message later, press Close. To read the message, select Menu >

Messaging > Inbox. Alternatively, with Info open, use the centre selection and navigation keys to highlight and open Unread messages. icon Incoming text messages accommodate the full 10 concatenations. However, incoming messages from emails are restricted to approximately 160 Latin and 74 non-Latin characters. If the sender exceeds this limit, the message will be truncated upon receipt. Viewing your received messages Inbox lists the last 20 messages received, including message status (read or unread), the senders name or number, the first words of the message and the date received. Use the up and down navigation keys to highlight a message and press the centre selection key or select Options > Open. Replying to sender Open the message and select Options > Reply. A new blank message will be displayed. Complete the fields as prompted. Forwarding a message Open the message and select Options > Forward > Text message or Email message. The message is displayed with the cursor flashing in the empty To: field. Enter the recipients number or to add a contact from the phonebook, press Options > Add recipient. When the To: field is completed, select Options > Send. A pop-

up confirms that the message has been sent. The sent message is stored in the Sent list. Calling a number from a received message Open the message and press the green key Options > Call. After the number has been called, the message is considered read and remains in the inbox. or select Saving details from a received message Open the message and select Options > Address clipboard. The senders number is displayed. Select Options > Add to contacts. You can either Create new or Update existing. Select which field to save the number in the contacts list, complete other fields as appropriate and select Options > Save. The contact will be stored in Phonebook. See Creating a new contact on page 40 for more information. Saving a received message To save a received message, open the message you wish to save and select Options > Copy to folder >

Saved messages. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 32 Deleting messages Select the message from the list displayed in any of the message folders and select Options > Delete. A pop-up will appear asking you to confirm the action. Press Yes. To delete all the messages in the folder, select Options >

Delete all messages. Setting up message groups If you regularly send the same text or email message to the same group of people, you can set up a group. Select Menu > Contacts > Groups, then select Options > Create new. Enter a name for your group and select OK, followed by Yes. You can set up a maximum of 20 groups, and the same contact can be a member of more than one group. To add members to a group, select Menu > Contacts >

Groups, highlight the group to which you would like to add members and press the centre selection key. Now select Options > Add member. This will retrieve your phonebook. Highlight the name of the contact you would like to add to the group and press the left or centre selection key. A group can have any number of contacts. By selecting Options when a member of the group is highlighted, you can also:

Open the contacts details Call the contact Send a Text message to the contact Remove from group to remove the contact from this group View group list to view the members of each group Assign group ringtone to give all members of this group the same ringtone, so that you will be able to recognise when a member of the group is calling you. To send a text message to the whole group, select Menu > Messaging > New message > Text message or Email message > Options > Add recipient and then press the right navigation key three times to move between the tabs. Select the group from the list and compose your message. You can also add members to groups directly from your phonebook. In your phonebook, simply highlight the contact, select Options > Add to group, then select which group to which you would like to assign the contact. You can also see which members belong to a group by selecting Options > Belongs to group. Messaging 1 2 3 4 5 6 7 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 33 Sending a text to a group of people If you regularly send the same text to a group of people, you can create a group in your phonebook. To send the text to a group you have already set up, select Options

> Add recipient and then press the right navigation key twice to display the list of groups. Using message settings Select Menu > Messaging > Options > Settings >

Text msg settings or Email settings. Text message settings:

Use same message centre: Always set to Yes. SMSC management: Both specify the number to which your phone will despatch your messages for delivery. Validity period: Specifies the length of time your message will remain in the network, should it be pending for delivery to the recipient. Saving sent messages: The default setting is on. The setting can be changed if required. Long message sending: The default setting is on. This allows approximately 1600 Latin or 740 non-Latin characters to be sent ie. up to 10 concatenations. With original text / Without original text: The senders original message is included/excluded as part of any reply that you compose. The default setting is Without original text. Set defaults: This resets all message settings. Entering your service centre number It is unlikely that you would need to enter or change your service centre number unless advised to do so by your service provider. The number of your service centre is required in order to send messages. In the unlikely event that this detail is not on your SIM card, you can enter the number yourself. To enter a service centre number, select Menu >

Messaging > Options > Settings > Text msg settings >

SMSC management. If the phone number of your service centre is displayed, select Options > Exit. If there is no number in the display, select Options > Edit and enter the full international number of the service centre. You will be prompted to activate the number. Press Yes. Your phone is now ready to send and receive messages. Alternatively, select Menu > Messaging > Options > Settings > Email settings > Options > Edit and add the email centre number and select Apply. Setting a message delivery expiry period If your message cannot be delivered, you can change the length of time your message will remain in the network. To check or change the expiry period select Menu >

Messaging > Options > Settings > Text msg settings >

Validity period. Messaging 1 2 3 4 5 6 7 Prepay services If you have a prepay subscription, your service provider will have informed you of the services available to you. Your phone also enables you to make a balance enquiry and redeem prepay vouchers for Inmarsats prepay service, free of charge. Select Menu > Settings > Prepay, then select either Balance enquiry or Redeem voucher and follow the on-screen instructions. Making a balance enquiry From the main screen enter your balance enquiry code,

*106# and press the green key

. Your current balance and expiry date will be shown on the screen. Redeeming a prepay voucher From the main screen enter the top-up code,

*101*VoucherNumber#, eg. *101*1234567890123456#

and press the green key

. Your new balance and expiry date will be shown on the screen. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 14 Connecting to the satellite 15 Using the eCompass function 15 Obtaining a GPS fix 16 Making and Receiving calls 20 Incoming call alerting 21 Calling handsfree 22 Using voicemail 22 Additional call features 24 Advanced call features 27 Messaging 34 Prepay services 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 34 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 35 Using the Assistance button In a critical situation, the Assistance button allows you to rapidly make a call to a recipient, or send an alert text message or email to one or more recipients. Note: An assistance alert is not the same as an emergency call, see page 19. You cannot set the feature to call a national emergency number (e.g. 911) or other numbers of less than four digits. However it is always good practice to save to your phonebook the contact details of related local services so that they can be alerted if necessary. Enabling the Assistance feature Before you can use the Assistance feature, you must enable it and configure the alert type and recipients. From the main menu select Location services > Assistance button > Configure > Assistance feature. Then press the centre selection key to enable the feature. Configuring Assistance button calls Go to Location services > Assistance button >

Configure > Alert type, then select Call only or Call &

message. Choose the intended recipient of your call by selecting Location services > Assistance button >

Configure > Call config. > Edit recipient. You can choose a contact from the phonebook or add a new contact. To find contacts, edit contacts or add new contacts, see Managing contacts in your phonebook on page 41. You can only select one recipient for an assistance call. If you want to use the handset loudspeaker when you make an assistance call, select Location services > Assistance button > Configure > Call config. > Handsfree call

> On. If you want the handset to automatically redial the recipient when the call setup fails, select Location services > Assistance button > Configure > Call config.

> Call retry > On. If the first call is unsuccessful, the handset disconnects and shows the text Call connection failed, retrying. The contact is then automatically re-

dialled after three minutes. The handset will make up to eight attempts to connect to the recipient, after which Assistance alert is de-activated. Configuring Assistance button messages Go to Location services > Assistance button >

Configure > Alert type, then highlight Call & message or Message only and press the centre selection key. Choose the intended recipient of your message by selecting Location services > Assistance button > Configure

> Message config. > Edit recipient. See Configuring assistance calls above. Then choose the type of message that you want to send to this recipient by selecting Email message or Text message. If you want to send a message to more than one recipient, select each contact from the LOCATION SERVICES Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 36 phonebook separately (adding new contacts if necessary) and choose the message type for each. A maximum of ten message recipients is permitted. Created 20140202T132216Z is the timestamp giving the date and time at which the alert was triggered The content of assistance messages is automatically created by the handset. It always includes an up-to-date GPS fix, the time at which the fix was acquired and the time that the alert was triggered. An email cannot exceed 160 characters, including the recipients email address, and users cannot personalise messages by entering additional text. Here is an example of an assistance message:

Assistance alert from:

+870776400465 52.123N,22.456W 20140202T125959Z h:08m,v:32m accuracy Created 20140202T132216Z where:

+870776400465 is the senders phone number 52.123N,22.456W is the latitude and longitude of the senders location 20140202T125959Z is the date and time at which the GPS fix was acquired h:08m,v:32m accuracy is the horizontal and vertical accuracy of the GSP fix in meters Activating an Assistance button alert With your handset switched on and the antenna deployed, flip open the latch of the Assistance button at the top of the handset and press the button revealed. Alternatively, from the main menu, select Location services >

Assistance button > Configure assistance button >

Send assistance alert. The on-screen text informs you that the alert will be sent in 15 seconds and that you can select Alert now to send it immediately. You can cancel the alert during this time, by pressing Cancel. Respond as necessary. If alert messages have been configured, they are then sent to the recipient(s). If alert call has been configured, then the call is established. During the call, the screen displays the latitude and longitude of your current location. Assistance button security You can lock the Assistance button feature to prevent unauthorised use. If the lock is on, you must enter the admin code before the features settings can be changed. See Setting up the admin code on page 54 for more information. The lock default setting is Off. To switch on or off the Assistance button lock, select Menu > Settings > Security and select Assistance button lock from the list. Then select On or Off, enter the admin code and press OK. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 37 Using the Tracking feature The Tracking feature allows you to send text messages or emails reporting the GPS coordinates of your current location to one or more recipients or, alternatively, to a tracking portal. The messages are automatically generated by the handset, with updated coordinates, at a default preset interval of 15 minutes. To send any message, your handset must be registered to the network. See Connecting to the satellite on page 14. Configuring Tracking Tracking status The Tracking feature has three states - Enabled, Disabled and Always-on - that control access to the sending of tracking messages. To configure the status, go to the main menu and choose Location services >

Tracking > Configure tracking > Tracking status. Then choose a state:

Enabled: allows you to start and stop sending tracking messages, either by navigating the menu or by using the Tracking button [graphic] above the volume up/

down keys on the side of the handset Disabled: removes the ability to start or stop the transmission of tracking messages Always-on: The handset continues to send messages whenever it is connected to the network Choosing the message recipients and message type Select Location services > Tracking > Configure tracking > Edit recipient. You can choose a contact from the phonebook or add a new contact. To find and edit contacts or to add new contacts, see Managing contacts in your phonebook on page 41. If you want to send messages to more than one recipient, select each contact from the phonebook separately (adding new contacts if necessary). A maximum of ten recipients is permitted. When you have chosen a recipient, press Select. The message types available for that contact are displayed, highlight Text message or Email message and press Select. Note that a recipients email addresses cannot exceed 40 characters. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 38 Choosing the message interval When Tracking is set to On, messages are automatically sent every 15 minutes by default. To stop sending tracking messages when Always-on has been selected, change the status by choosing Location services > Tracking > Configure Tracking > Tracking status > Disabled. You can increase or decrease this interval to suit your requirements. Select Configure tracking > Edit interval. The screen displays preset time intervals. Highlight an interval value and press Select. You can also specify your own interval of up to 9999 minutes by choosing Custom interval from the list of intervals. A blank text box is displayed. Type the interval that you want to use and press OK. Starting tracking If the Tracking status is set to Enabled, you can start and stop sending tracking messages by using the Tracking button. Alternatively, from the main menu choose Location services > Tracking > Start. On-screen text confirms that tracking messages will be sent at the chosen interval. Press OK. If you have chosen Always-on override, tracking messages are sent whenever the handset is registered to the network. The tracking LED above the screen flashes when Tracking has started. Stopping tracking To stop sending tracking messages, press the Tracking button or choose Location services > Tracking > Stop and press Select. An on-screen prompt asks you to confirm, press OK. The tracking LED goes off. Tracking security You can lock the Tracking feature to prevent unauthorised use. If the lock is on, you must enter the admin code before you can change the Tracking features settings. See Setting up the admin code on page 54 for more information. The lock default setting is Off. To switch Tracking lock on or off, select Menu > Settings

> Security and select Tracking lock from the list. Then select On or Off, enter the admin code and press OK. Using your GPS location information As well as locating your phones position for the satellite, you can also view your GPS location and send it as a text message or email. Note: You can view GPS information only after the phone has been registered to the network. Viewing your GPS location information Select Menu > GPS position > Options > View location information to view the date and time of when your last GPS fix was taken and your latitude and longitude at that time. Your exact location is indicated with a white dot on the world map. 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 35 Using the Assistance button 37 Using the Tracking feature 38 Using your GPS location information 39 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 39 Displaying GPS in metric or imperial measures Select Menu > GPS position. The Valid GPS fix screen appears. Select Options > Set unit and make your selection. The default setting is metric units. Sending your GPS location Select Menu > GPS position and select Options > Send GPS location. The elapsed time since the last GPS fix was obtained is displayed and you are presented with two options. Select Send to use the stored value or New to acquire a new GPS fix. Press the red key cancel. Make your decision on the basis of any significant distance travelled since the stored GPS fix was obtained. Note that requesting a new fix will temporarily delay the sending of your location. to When the GPS fix to be used has been acquired, select Text message or Email message. Only editing of the recipient field is permitted. Enter the destination number or email address directly into the To: field, or choose Options > Add recipient to select an existing entry from Contacts. You are presented with the list of Phonebook contacts. Use the left and right navigation keys to select SIM contacts or Groups. Obtaining a GPS fix manually On rare occasions, your phone may continue to show the GPS fix required icon, which means that a new GPS fix is needed in order for your phone to connect to the network. If this occurs, select Menu > GPS position. The new GPS fix is displayed. When this screen is open, your phone will attempt to refresh the GPS fix every 30 seconds. National GPS policies Some national GPS policies do not allow users to access their GPS information in particular locations. Your phone continues to access the GPS satellites as usual, so its performance is unaffected. However, your phone will not display its GPS location. For more information, please contact your service provider. GPS Data Inmarsat will collect, store and process GPS data in accordance with applicable data protection laws. Personal alert The personal alert feature enables a user to send their GPS position, along with a short pre-configured message, as an email or text message, to a maximum of 10 recipients. Pre-configuration, use of a stored GPS fix and a short-

dial code enable the personal alert to be sent quickly whilst maximising reliability. This is achieved by restricting the alert to one 160 character message, and mailing to each recipient separately. Each message sent is charged separately. Note: Generally, email message routing is more reliable than text messages. Setting up and activating a personal alert To set up and activate a personal alert, select Extras >

2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 34 Using the Assistance button 36 Using the Tracking feature 37 Using your GPS location information 38 Personal alert 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 40 Sending a personal alert The quickest way to send a personal alert is to press

* and # simultaneously for at least 2 seconds from the main screen. Alternatively, select Menu > Extras >

Personal alert > Send personal alert. A pop-up will appear asking you to confirm the action. The antenna must be deployed and your phone connected to the satellite to successfully send personal alert messages. Personal alert > Edit personal alert. Select Configure personal alert, and edit the recipients and the message. See the Messaging section starting on page 27 for more information. The personal alert is made up of the following elements:

Last GPS fix, time of GPS acquisition and fix accuracy Time that the personal alert was triggered on the phone Email address of the recipient if the alert is sent as an email A short message predefined by the user, written in Latin characters. This personalised text is limited in length; a descending counter indicates available characters when editing. The same message is sent to all recipients You can restrict access to the Edit personal alert feature by switching on Personal alert lock in Menu > Settings

> Security and entering the admin code. The default for Personal alert lock is off. See Setting up the admin code on page 54 for more information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Finding a contact You can find a contact in your phonebook either by using the navigation keys to scroll through the list of all contacts or by entering the first characters of a contacts name in the search field at the top of the list of contacts. See Entering text on page 28 for more information. Opening a contact Highlight the contacts name in the phonebook and press the centre selection key or select Options > Open. Use the up and down navigation keys to select a number. Ordering contacts by first or last name Select Phonebook > Options > Settings > Display name order and then select either First last (to list them alphabetically by first name) or Last first (to list them alphabetically by last name). Managing contacts in your phonebook Contacts can be stored in either your phones memory via Phonebook or on your SIM card via SIM contacts. Up to 500 contacts can be stored in the phonebook and up to 250 on your IsatPhone 2 SIM card. To view the contacts in your phones memory, select Contacts from the main screen. Creating a new contact There are several ways to create a contact. From the main screen type in the number to save, including the full international code. Select Options > Add to contacts >

Create new contact. Define the number you are saving, eg. Telephone, Office phone, Mobile phone, Fax etc, then select Options > Save. The saved contact details are displayed. Alternatively, open the contacts directory either by selecting Menu > Contacts or by selecting Contacts. Highlight the location where you wish to save the contact and press Select. The default setting is Phonebook. You are presented with a list of stored contacts, select Options > New contact. Enter the first name, last name and the telephone number. If you wish to save a contact detail other than phone number, select Options > Add detail and select from the list presented. After entering all relevant details, select Options > Save or press the centre selection key. 41 Managing contacts in your phonebook 1 2 PHONEBOOK & CONTACTS Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Deleting a contact Select Menu > Contacts or press Contacts. Select from the list. Use the navigation keys to highlight the stored contact that you would like to delete. Select Option >

Delete. You will be prompted to confirm the deletion by pressing Yes. Deleting all contacts Open your phonebook, select Options, select Delete all and then select Yes. Duplicating a contact Duplicating a contact can be a quick way to add a new contact with similar details to an existing one. Highlight the contact you wish to duplicate, select Options

> Duplicate and then amend the new contacts details. When you have finished, save the new contact by pressing the centre selection key followed by Yes. Editing a contact To change or add details for a contact already in your phonebook, use the up and down navigation keys to highlight the contact, then select Options and select Edit. Move between the details using the navigation keys. Edit the text or numbers. See Entering text on page 28 for more information. To save the changes to the contact, press the centre selection key and then select Yes. Or select Options > Save > Yes. To discard changes, press the centre selection key and when prompted to save changes, select No. Alternatively, select Options > Save > No. See Entering text on page 28 for more information. Calling a contact Highlight the contacts name and press the green key If there is more than one number stored for that contact

(eg. office and mobile) select one of them using the centre selection key. Texting or emailing a contact Highlight the contacts name, select Options > Send message. Select Text message or Email as appropriate. Write your message and select Options > Send. If you are sending a text message and there is more than one number stored for that contact select one using the centre selection key. 42 Managing contacts in your phonebook 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 43 Managing contacts on your SIM card Contacts can be stored on your SIM card as well as in Phonebook. Storing contacts on your SIM card allows you to move contacts from one phone to another. Storing contacts on both the SIM card and the phonebook allows you to back-up your contacts. To view the contacts on your SIM card, select Menu >

Contacts > SIM contacts. You can navigate, edit, delete, make calls or send texts in exactly the same way as Phonebook. To copy a contact from your SIM card to your phonebook highlight the contact in SIM contacts, select Options and select Copy to phonebook. To copy all SIM card contacts to Phonebook, this option arises when the SIM card is inserted. The first time Contacts is accessed after inserting the SIM card, you will prompted to Copy SIM contacts to Phonebook and to confirm the action. Please note that this process may take a little time. To copy a contact from your phones memory to your SIM card, select Phonebook and highlight the contact. Select Options > Copy to SIM. To delete all contacts from your SIM card, select Menu >

Contacts > SIM contacts > Options > Delete all. To find out how many contacts are stored on your SIM card and how many more you can add, select Menu >

Contacts > SIM Contacts > Options > SIM details. Synchronising contacts with Outlook The Contact Synchronisation Tool, supplied with your phone, enables you to transfer contact information held in Microsoft Outlook or Outlook Express on your PC with that stored on your phone. Run the USB drive, supplied with your phone, to download the Contact Synchronisation Tool and to access the How to Synchronise your Contacts guide. These are also downloadable from inmarsat.com/isatphone. Sending and receiving contact details To send a business card, highlight the appropriate contact in your phonebook or SIM contacts folder and select Options > Send business card. Select either Text message or Email message. A text or email message is displayed including all details stored for this contact in the body of the message. Enter the full international phone number of the recipient in the To: field or select Options >

Add recipient to specify a stored contact. Select Options

> Send. When you receive a business card, it will appear as a normal message in your Inbox, but the title of the message will be Business card. Highlight the message and press the centre selection key or select Options > Open. The contact details are presented like any other entry in the phonebook. To save Business card details, select Options > Create new or Update existing. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 41 Managing contacts in your phonebook 43 Managing contacts on your SIM card 43 Synchronising contacts with Outlook 43 Sending and receiving contact details 44 Your phone number 44 Your service provider number 44 Alarm 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 44 Business card details are saved to your phonebook. Once the details have been saved, the original message is deleted from your Inbox. Your phone number From the main screen, open Info by pressing the centre selection key and selecting My phone number. Your phone number is usually programmed onto your SIM card by your service provider. If not, the entry will be blank. You can enter the number yourself by selecting Menu > Contacts > My phone number. If a SIM card is subsequently inserted with a stored phone number, your entry will be overwritten. Your service provider number Open Info by pressing the centre selection key and selecting Service provider or for full details select Menu > Contacts > Service provider. These details are programmed onto your SIM card and are not editable. icon is displayed on the status bar. The Alarm You can use your phone as an alarm clock. When set, the alarm alarm will sound for 60 seconds at the same volume as the phone is set to ring. If you do not press a key while the alarm is sounding it will snooze for 9 minutes before sounding again. This will continue until you switch the alarm off. Setting an alarm Select Menu > Alarm and select the type of alarm. Once alarm sounds the next time the clock shows the selected time. Recurrent alarm sounds regularly, on selected days of the week. Enter the alarm time and select OK. If this is a recurrent alarm, use the navigation and centre selection keys to tick which days of the week it should sound, then select OK. Silencing a ringing alarm When the alarm sounds, select Stop or the centre selection key. If you press the right selection key Snooze, it will sound again in 9 minutes. Cancelling an alarm Select Menu > Alarm, select which alarm you would like to remove, then select Options > Remove and confirm your choice. Your phone can be used as a modem to send and receive low rate data. Typical low rate data applications include plain text email and small file attachments. Some Inmarsat service providers offer proprietary applications which have been optimised to operate with your phone. Contact your service provider for details. To enable your handset for the data service:

1 Install the USB Drivers on your PC. To do this, run the USB Drivers supplied with your phone. Download the USB Drivers and access the How to Install USB Drivers guide. These are also downloadable from inmarsat.com/isatphone. 2 Place your phone on its side, raise the antenna and ensure the handset is ready for service. 3 Connect the handset to your PC using the USB cable. 4 Identify the modem COM port to which your phone is connected for the data service. The COM port number will be needed when you are using your data application. To do this, on your PC go to Control Panel > Phone and Modem options and select the Modem tab. You will see IsatPhone 2 Modem and the COM port eg. COM6. Or, go to Control Panel > System and select the Hardware tab. Click on Device Manager and scroll down to Modems. If your USB Drivers are installed you will see IsatPhone 2 Modem. Right click on IsatPhone 2 Modem and select Properties. You will see the Com port eg. COM6. 5 If you have not already done so, install your chosen data application and follow the onscreen instructions. You only need carry out the steps above once. For all subsequent connections, enter your data application and follow the onscreen instructions. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 45 DATA Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 46 Sounds, Ringtones and Profiles Your current sound profile is always displayed in the status bar of the main screen, and can also be accessed via Info. To change your phones sound profile, select Menu >

Profiles, and highlight the one you want and press the centre selection key. There are four sound profiles:

General for everyday use Silent no vibration or sound Loud for noisy environments Vibrate only vibration and no sound You can customise any of these profiles by highlighting it, selecting Options and selecting Personalise. This allows you to change the following aspects of the sound profile:

Vibrate mode on or off Alert volume sound level Keypad volume sound level when a key is pressed Alert ring mode constant, ring once, beep, silent or increasing volume Ringtone the sound your phone makes when it receives a call Key sound the sound your phone makes when a key is pressed Message alert the sound your phone makes when it receives a text message Highlight the setting you would like to change, press the left or centre selection key, use the navigation keys to alter the setting and press Select. To restore the default settings for a sound profile, highlight the profile, select Options > Reset to default. Selecting a ringtone Each profile can play one of 8 ringtones to notify you of an incoming call. Select Menu > Profiles and highlight the appropriate profile. Select Options > Personalise > Ringtone from the list and press Select or the centre selection key. The current ringtone for the profile is played and highlighted in the list. Use the navigation keys to highlight and hear the other ringtone files available. Press Select or the centre selection key to specify the highlighted ringtone. If no sound is heard when you highlight a ringtone, the Alert volume for your profile may be set to 0. This is the default for both Silent and Vibrate only. To change the ringtone volume, select Back to return to Profiles. Highlight Alert volume and press Select. Sounds, ringtones and profiles 1 2 PERSONAL SETTINGS Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 47 Allocating a unique ringtone to callers You can allocate a specific ringtone to a contact. Regardless of the active profile, the allocated ringtone will be used for the specified caller, but the alert volume of the active profile will be respected. Highlight the desired contact entry in your Phonebook or SIM contacts and press the centre selection key or select Options > Open. Highlight the relevant contact detail and select Options > Assign ringtone. From the list of available ringtones, highlight your preference and press Select. The name of the ringtone will be displayed under the contact detail specified. To remove an associated ringtone, open the contact entry, highlight the ringtone and select Options > Remove ringtone. Setting phone and writing language The display and writing language of the phone can be changed by selecting Menu > Settings > Language. Highlight any of the following options and press Select:

Phone language to set the display language of the phone Writing language to set the texting language of the phone Predictive text to set the text editing mode for composing messages Setting phone language The first time you switch on your phone, you will be prompted to select the display language. You can change this at any time. Select Menu > Settings > Language

> Phone language, highlight the desired language and press the left or centre selection keys. If you do not understand your phones current language setting, follow these directions to navigate to the Phone language menu. Press the red key to return to the main screen Press the left selection key to go to the menu screen Press the down navigation key twice to highlight the Settings icon Press the centre selection key to open Settings Press the down navigation key twice to highlight the Language icon and press the centre selection key Press the centre selection key and use the navigation keys to highlight the correct language and press the centre selection key again to change the phones language Sounds, ringtones and profiles 1 2 Setting writing language Select Menu > Settings > Language > Writing language. Select the desired language and press OK. Setting predictive text The predictive text setting is used to set the text editing mode for composing messages. Select Menu > Settings >

Language > Predictive text. Select Available or Hidden. The default setting is available. See Using predictive text entry on page 28 for more details. Setting date and time Your phone automatically receives UTC time from GPS satellites. The first time you use your phone, you will be prompted to select a language from the list, followed by the option to select your local time. When completed, local time will be displayed on the status bar. You will need to reset the time when you travel to different time zones. The Date and time menu lets you change the date and time format. Changing keypad Your phone is supplied with a Latin keypad as standard. Dual-alphabet keypads are available in Latin with Arabic, Japanese or Russian characters. If your phone does not have your preferred keypad, contact your service provider. Setting the time Select Menu > Extras > Date and time > Time settings. Setting the date Select Menu > Extras > Date and time > Date settings. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 48 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 49 Customising display settings Lighting the keypad and screen The backlights for the screen and keypad can be controlled by going to select Menu > Settings > Display. Select any one of the following options and press Select to save your changes. Brightness to set the brightness of the screen Screen light to set the duration for screen backlights Keypad light to set the duration for keypad backlight Screen standby to set the duration for the screen backlights after the last keystroke Setting the time zone You may wish to change the local time zone on your phone if you move to a new location or if your new phone is not displaying the correct time zone. You may also wish to know the time in another location, eg. your head office. Setting the local time zone Select Menu > Extras > World time. The world time map appears. Select Options > Select > Local time zone. Use the navigation keys to highlight the required time zone and press Select. Setting the remote time zone Select Menu > Extras > World time. Select Options >

Select remote time zone. Use the navigation keys to highlight the required time zone and press Select. Setting daylight saving time (DST) Select Menu > Extras > World time. Select Options and select from a list to enable/disable local/remote DST. DST is displayed as 0 or +1 on the world map. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 50 Setting up keypad lock The keypad lock disables the keypad and prevents accidental dialling. When activated, the phone will respond to the green to answer or reject call. and red keys Bluetooth The Bluetooth connection on your phone allows you to connect wirelessly to a Bluetooth headset enabling you to use the phone in handsfree mode. Select Menu > Settings > Security, select Automatic keypad lock, and then select the duration before the keypad is locked. Deactivate the automatic keypad lock using the same menu. To activate Bluetooth connectivity select Menu >

Settings > Bluetooth. Select Settings > Bluetooth and select On. The Bluetooth icon indicator appears in the status bar. To lock the keypad, ensure the main screen is displayed, press the centre selection key followed by the * key within 3 seconds. The keypad locked the status bar. icon is displayed on To unlock the keypad, press the centre selection key followed by the * key on the keypad within 3 seconds. Setting up phone lock Phone lock protects your phone against unauthorised use. Select Menu > Settings > Security and select Phone lock. Specify the idle period, from 30 seconds to 30 minutes, after which time the phone will automatically lock. You will be prompted to Enter phone lock code. To unlock the phone, enter the code when prompted. The default admin code is 123456. See Setting up the admin code on page 54. The new setting will be accepted when the code is accepted. Connecting a new Bluetooth device The first time you use a particular Bluetooth headset with your phone, you will need to pair the phone and the headset. Ensure the Bluetooth headset is switched on before you begin. Select Menu > Settings > Bluetooth > Paired devices. A list of Bluetooth devices in range of your phone will appear on the screen. If the device does not appear, select Options and select Search for devices from the new menu that appears. Searching... will be displayed at the top of the screen, followed by the names of all the devices in range. A blue tick will be displayed next to any devices already paired with your phone. Select the device you want to pair and enter its pass code. Bluetooth devices such as headsets generally have their pass code set in the factory and printed either on the device or its packaging. Some devices allow you to set the pass code yourself. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 51 The device should now be listed in the Paired devices menu. Highlight it and press the left selection key, then select Connect from the menu. The device should now be listed on the Connected devices menu accessed from the Bluetooth menu. This phone is connected with a Bluetooth headset. icon indicates that your Whenever the device attempts to make a connection with your phone, you will be prompted whether you want to accept the connection. To automatically accept connection requests from a particular device, highlight it in the Paired devices menu, select Options and select Set as authorised. You should only authorise devices that belong to you, or that you trust. If you no longer want a device to be authorised, select Set as unauthorised. To connect a different headset, you must disconnect the current headset. Highlight the device on the Connected devices menu, select Options and select Disconnect. If you no longer want a headset to be paired with your phone, highlight it on the Paired devices menu, select Options and then select Delete. Other choices in the Options menu are Rename, which allows you to select a more descriptive name for your headset, and Device attribute, which displays the headsets name, and the time and date at which it was connected. When you are not using Bluetooth connectivity, select Bluetooth > Off or My phones visibility > Invisible. This prevents unauthorised connection. Do not pair with an unknown device. Setting up Bluetooth lock If Bluetooth lock is enabled, the phone will require the admin code to be entered before Bluetooth settings can be changed. See Setting up the admin code on page 54 for more information. The default setting is off. To enable or disable this feature, select Menu > Settings

> Security and select Bluetooth lock from the list. Select On or Off and then enter Admin code. Operating a Closed User Group

(CUG) The Closed User Group (CUG) service allows you to form closed user groups from which access is restricted. A user may be a member of one or more CUGs. Members of a specific CUG can communicate amongst themselves but not, in general, with users outside the group. This feature is operated by your service provider who will provide further instructions on its use. The default setting is off. To enable, select Menu > Settings > Security >

Closed user group, select On, enter your CUG number and press OK. Group numbers range from 0-9. If the CUG is on, the CUG index icon appears on the status bar. Reset all settings Select Menu > Settings > Reset settings. You will be prompted for the Admin code in order to make this change. See Setting up admin code on page 54 for more information. Returning to default settings will not affect your admin or user codes, PINs, organiser entries, contacts, messages or call logs. To return these to default setting or to delete these entries see:

Setting up SIM PIN code on page 55 Setting up SIM PIN 2 code on page 55 Deleting a contact on page 42 Deleting SIM contacts on page 43 Deleting messages on page 32 Deleting all call logs on page 23 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 46 Sounds, Ringtones and Profiles 47 Setting phone language 48 Setting date and time 49 Setting the time zone 49 Customising display settings 50 Setting up keypad lock 50 Setting up phone lock 50 Bluetooth 51 Operating a Closed User Group (CUG) 52 Reset all settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 52 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 53 Security locks and codes SECURITY FEATURES CONTROLLED BY ACTION DEFAULT SETTING DEFAULT CODE CODE LENGTH The Phone Keypad lock Admin code Only the green and red keys are active Creates Phone lock Restricts access to Bluetooth Restricts access to Reset settings Restricts access to Personal alert Creates User code The SIM card PIN PIN 2 The network Barring password Restricts access to SIM card Rest Restricts access to Fixed number dialling Restricts access to Call barring Centre selection key and *

123456 6 digits 4-6 digits 8888 9999 4-8 digits 4-8 digits 0000 4 digits Off Off Off Off Off SECURITY Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 54 Security can be controlled by the phone, the SIM card or the Inmarsat network. This enables you to match security requirements to your needs. The keypad lock prevents accidental dialling; the phone lock prevents an unauthorised user from using your phone even if they replace the SIM card. The SIM PIN prevents an unauthorised user from using your SIM even if they place it in another phone. The admin code restricts access to particular features on the phone. For example, an individual might only wish to activate the keypad lock. A corporate organisation might choose to restrict functions available to their employees by activating the admin code and issuing a user code. Security features controlled by the phone Access to your phone can be restricted by the keypad lock to prevent accidental dialling (see Setting up keypad lock on page 50 for more information) or by activation of the admin code. The admin code can be activated: to create a Phone lock; restrict access to Bluetooth lock, Personal alert lock and Reset settings; and to create a User code so that a third party can use the phone but not have access to the restricted features. See Setting up Bluetooth lock on page 50 and Reset all settings on page 52 for more information. Setting up the admin code Select Menu > Settings > Security and select Admin code. You will be prompted for the current code. The default setting is 123456. When this is accepted, you will be prompted to enter your new code and then confirm it. The code must be 6 digits long. If you lose your admin code, contact your service provider. The default setting is off. The admin code can be entered incorrectly an unlimited number of times. If you have forgotten your code, contact your service provider. Setting up the user code Select Menu > Settings > Security and select User code. You will be prompted to enter the 6-digit Admin code. Once this is accepted, you will be prompted to create a new user code and to confirm it. The code can be 4-6 digits in length. The default setting is off. The user code can be entered incorrectly an unlimited number of times. If you have forgotten your code, contact your phones administrator. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 53 Security locks and codes 54 Security features controlled by the phone 55 Security features controlled by the SIM card 55 Security features controlled by the network 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 55 Security features controlled by the SIM card Access to your SIM card can be restricted by activating its PIN code. The advanced call feature, Fixed number dialling, can be protected by your SIM PIN 2 code. See Fixed number dialling on page 26 for more information. Setting up SIM PIN code Select Menu > Settings > Security > PIN request and select On. You will be asked to enter your SIMs PIN code. If you make an error entering the number, press Cancel to clear the digits and re-enter. Press the centre selection key or OK. The default 4-8 digit code for SIM PIN is 8888. The default setting is off. To change the PIN code stored on your SIM card, select Menu > Settings > Security > Set PIN. Enter the existing PIN code, then the new PIN. Repeat the new PIN to confirm it. If the PIN code is entered incorrectly three times, your SIM card can only be unlocked using the PUK code. Contact your service provider if you do not have a record of your PUK code. If the PUK code is entered 10 times incorrectly the SIM will lock and you should contact your service provider. The default setting for PIN is off. Setting up SIM PIN 2 code The default 4-8 digit code for PIN 2 is 9999. The default setting is off. If the PIN 2 code is entered incorrectly three times, your SIM card can only be unlocked using the PUK 2 code. Contact your service provider if you do not have a record of your PUK 2. If the PUK 2 code is entered 10 times incorrectly the SIM will lock and you should contact your service provider. To change the PIN 2 code, select Menu

> Settings > Security > Set PIN 2. Enter the existing PIN 2 code, then the new PIN 2 code. Repeat the new PIN 2 code to confirm it. Security features controlled by the network When enabled, the advanced call feature, Call barring, is protected by a code. The default setting is off. See Call barring on page 24 for more information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM SOLUTION My phone will not switch on Check if the battery is inserted correctly Check if the battery needs charging. Charging for 20 minutes should provide enough power to switch the phone on If the battery does not charge it has probably exceeded its usage period and you will need to replace it with a new one My phone cannot make or receive calls Ensure the SIM card is inserted in the phone and is fully provisioned by your service provider Check you have a valid GPS fix (See Using your GPS location information on page 38 for more information) Ensure the phones antenna is fully extended and you have a clear line of sight to the satellite. See Connecting to the satellite on page 14 for more information. A least two signal bars are required to make and receive calls If you have less than two bars signal strength, rotate the phone and angle the antenna until the signal strength increases and you are able to make and receive calls If the phone has sufficient signal strength and cannot make or receive calls, check if Call barring (page 24), Diverting calls (page 25) or Fixed number dialling

(page 26) have been activated If you have a prepay subscription, check your prepay balance to ensure you have sufficient credit to make a call. See Making a balance enquiry on page 34 for more information Contact your service provider if you are unable to resolve the problem 56 Troubleshooting 1 2 3 TROUBLESHOOTING Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM My phone cannot receive a text message My phone continues to display Searching satellite My phone displays a language I do not understand SOLUTION The phone can store a maximum of 20 messages in its memory. If the memory is full, delete a few texts to free up memory for new messages. See Deleting messages on page 32 for more information If you still cannot receive a text, your service centre number may not be correct. See Entering your service centre number on page 33 for more information or contact your service provider Ensure your phones antenna is fully extended Ensure your phones antenna is pointed towards the satellite. Press Help for onscreen guidance. Consult the Coverage map on page 9 to ensure you are within coverage Ensure there is a clear line of sight to the satellite with no obstacles which could block the signal. See Connecting to the satellite on page 14 for more information Contact your service provider if you are unable to resolve the problem Press the red key to return to the main screen Press the left selection key to go to the menu screen Press the down navigation key twice to highlight the Settings icon Press the centre selection key to open Settings Press the down navigation key twice to highlight the Language and press the centre selection key icon Press the centre selection key and use the navigation keys to highlight the correct language and press the centre selection key again to change the phones language 57 Troubleshooting 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index PROBLEM SOLUTION My phone does not display a GPS position Some national policies do not allow users to access their GPS information in particular locations. Your phone continues to access the GPS satellites as usual, but your phone will not display its GPS location My phone does not seem to receive voicemails My phone and/or SIM has been lost or stolen How do I contact my service provider?

Ensure your service provider has enabled voicemail Contact your service provider as soon as possible so your phone and/or SIM can be barred Your service provider number is stored on your SIM card. To view your service provider open Info by pressing the centre selection key and selecting Service provider 58 Troubleshooting 1 2 3 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 59 Caring for your IsatPhone 2 60 Certifications 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Caring for your IsatPhone 2 Your IsatPhone is a highly sophisticated electronic device. Complying with the following recommendations will help you to protect your warranty coverage and extend your phones life:

Keep your phone dry. Liquids or moisture can contain minerals that will damage electronic circuits. If your phone does get wet, dry it with a soft absorbent cloth as soon as possible, remove the battery and allow your phone and battery to dry completely before replacing it The connector covers are intended to protect your phone. When the connectors are not in use, keep these covers firmly closed at all times. Ensure that the connectors are free from dust or dirt before connecting any accessory. When closing the connector cover, ensure the area around the connectors, and the rubber sealing surfaces of the cover are clean and free from dirt. Ensure that the cover is fully closed to give maximum protection to your phone Do not store your phone in dusty, dirty or damp areas as this may shorten its life Do not store your phone in direct sunlight, or in places where the suns heat can be focused, like on the dashboard of a vehicle Do not store your phone and battery in extreme cold and hot areas exceeding a temperature range of -20C to +70C (-4F to +158F). Extreme temperatures can shorten the life of your phone and damage the battery Your phones operating temperature range is -20C to

+55C (-4F to +131F). The charging temperature range is 0C to +45C (+32F to +113F) If you are carrying a separate battery, keep it inside the plastic bag supplied. Always keep batteries separated from other metallic objects and keep it dry to prevent damage If your phone displays Battery overheating, switch it off and place in a cool area Do not use harsh chemicals, cleaning solvents or strong detergents to clean your phone Do not paint your phone Do not attempt to disassemble your phone or undertake repairs yourself Use only the Inmarsat-supplied or an approved replacement antenna. Unauthorised antennas, modifications or attachments could damage the device and may violate regulations governing radio devices 59 Care and maintenance 1 2 CARE AND MAINTENANCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 59 Caring for your IsatPhone 2 60 Certifications 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index Use only Inmarsat-supplied or approved batteries, and recharge your battery with Inmarsat-supplied or approved chargers for the phone When using any cable connections with your phone, ensure that it cannot be stepped on, tripped over or otherwise subjected to damage or stress Upgrade your phones firmware when advised to do so by Inmarsat or your service provider These suggestions apply equally to your phone, battery, chargers, and any accessory. If your phone is not working properly, contact your service provider. Certifications Your IsatPhone 2 is certified with an Ingress Protection rating of IP65, which means that your phone is resistant to dust and splashing. Do not store fully charged or low charge batteries for long periods of time without use. 80% charge is optimal for storage. The battery should be stored in dry conditions, not assembled into the handset, with the contacts protected. Ideal conditions are between

-20 and +20 C. Please check the remaining power levels in the battery and test the handset every three months. Recharge if the power has dropped below 40%. More frequent checking and recharging may be necessary depending on storage conditions. When the battery charge is very low, it may take some time for the charging indicator to show on the screen after connecting the charger. To view the battery % charge remaining, please look in Settings > About. Unplug the charger from the power socket and your phone when not in use. Do not leave a fully-charged battery connected to a charger, as overcharging may shorten its life. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Batteries gradually lose their charge even when the phone is completely switched off. When the talk and standby times are noticeably shorter than normal, replace the battery 60 Care and maintenance 1 2 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 61 European declaration of conformity and CE marking Inmarsat Global Limited hereby declares that IsatPhone 2 is in conformity with the essential requirements and other relevant provisions of the Radio Equipment Directive (2014/53/EU) and the Recast Restriction on Hazardous Substances Directive

(2011/65/EU). A copy of the original Declaration of Conformity can be found at:

inmarsat.com/service/isatphone2/ under Specifications. IsatPhone 2 is in conformity with the following standards and/or normative documents:

Health and Safety: IEC 60950-1:2005 + AMD1:2009 + AMD2:2013, IEC 62368-1:2014, EN 50360:2017. EMC: EN 301 489-1 V2.1.1 (2016-11), EN 301 489-17 V3.1.1 (2017-02), EN 301 489-19 V2.1.0 (2017-03) , EN 301 489-20 V1.2.1 (2002-11), EN 55032:2015. Spectrum: EN 301 681 V2.1.2 (2016-11), EN 303 413 V1.1.1 (2017-06), EN 300 328 V2.1.1 (2016-11). The technical files relevant to the above declaration are held at Inmarsat Global Limited, 99 City Road, London EC1Y 1AX, United Kingdom. Inmarsat IsatPhone 2 is capable of operating in frequency range of 1626.5-1660.5MHz - 1668-1675MHz, which has geographical and region-based restrictions in the countries mentioned in table on the right. The terminals frequency assignment is controlled by the network. Where restrictions apply, the network will not assign restricted frequencies to the terminal. The user is not required to take any action regarding restricted frequencies. BE DE LT FI HU SK FR IT UK REGULATORY AND COMPLIANCE Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 62 FCC Part 15 declaration IsatPhone 2 complies with Part 15 of the FCC Rules and, as such, operation is subject to the following two conditions:

1 This device may not cause harmful interference, and Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help 2 This device must accept any interference received, operation including interference that may cause undesired FCC caution: Under 47 CFR 15.21, changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference as follows:

Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver GMPCS IsatPhone 2 carries the International Telecommunication Union (ITU) Global Mobile Personal Communications by Satellite (GMPCS)-MoU mark. Industry Canada This Class B digital apparatus complies with Canadian ICES-003, CAN ICES-3 (B)/NMB-3(B). Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 61 European declaration of conformity and CE marking 62 FCC Part 15 declaration 62 GMPCS 62 Industry Canada 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area 63 RoHS compliance 63 REACH Regulations 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 63 Disposal of electrical and electronic equipment and batteries within the European Economic Area Directive 2012/19/EU regulates the disposal of electrical and electronic equipment in the EU and Directive 2006/66/EC regulates the manufacture and disposal of batteries in the EU. Inmarsat intends to join an EU certified Producer Compliance Scheme (PCS) to meet its obligations as a producer under these Directives. Electronic equipment and batteries should not be included as household waste but should be left at an appropriate collection point for recycling. This helps prevent potential negative consequences for the environment and human health. Check local regulations by contacting your local city office, your household waste disposal service, the vendor of your phone or calling Inmarsats or your local service providers call centre. Do not attempt to remove internal batteries. Internal batteries shall be removed only by a waste treatment facility or trained service professional. The crossed out wheeled-bin symbol on IsatPhone 2 and its rechargeable battery reminds you that all electrical and electronic products and batteries must be taken to separate collections at the end of their working life. This applies to the EU and other locations where separate collection systems are available. Please note that lithium ion batteries meet the definition of dangerous goods in international transport legislation and therefore customers must check with the relevant postal operator before posting any batteries. RoHS compliance IsatPhone 2 complies with the EC Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment 2011/65/EU (RoHS Recast). REACH Regulations IsatPhone 2 complies with the EC Regulation on Registration, Evaluation, Authorisation and Restriction of Chemicals No. 1907/2006 (REACH). This User Guide is published by Inmarsat without any warranty. Except as provided by applicable law and in the IsatPhone 2 end-user Warranty, no warranties of any kind, either express or implied, including, without limitation,the implied warranties of satisfactory quality, merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or completeness of this User Guide. Inmarsat reserves the right to make changes to this User Guide at any time and without prior notice. All illustrations are for illustration only and are not an accurate depiction of an actual IsatPhone 2. All rights are reserved. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 64 DISCLAIMER Inmarsat provides the following in-box accessories with the IsatPhone 2:

Battery USB drive Mains charger and four universal plug adaptors Car charger Micro USB cable Wired handsfree headset Wrist strap Holster Inmarsat reserves the right to add or delete accessories from this list at our absolute discretion. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 65 ACCESSORIES IsatPhone 2 and in-box accessories may contain commodities, technology and/or software subject to export controls and regulations imposed by the US and other countries. Diversion contrary to law is prohibited. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 66 EXPORT CONTROLS Malicious software (also commonly referred to as malware) is software that can harm the phone or other computers. Malware or harmful applications can include viruses, worms, spyware, and other unwanted programmes. While the phone does employ security measures to resist such efforts, Inmarsat does not warrant or represent that the phone will be impervious to the introduction of malware. You can, however, reduce the risk of malware attacks by exercising care when downloading content or accepting applications, refraining from opening or responding to messages from unknown sources, using trustworthy services to access the Internet, and only downloading content to IsatPhone 2 from known, reliable sources. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 67 MALWARE IsatPhone 2 has the capability to download, store and forward additional content. The use of such content may be restricted or prohibited by rights of third parties, including but not limited to restriction under applicable copyright laws. You, and not Inmarsat, are entirely responsible for additional content that you download to or forward from your phone. Prior to your use of any additional content, please verify that your intended use is properly licensed or is otherwise authorised. Inmarsat does not guarantee the accuracy, integrity or quality of any additional content or any other third party content. Under no circumstances will Inmarsat be liable in any way for your improper use of additional content or other third party content. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 68 DOWNLOADING CONTENT INMARSAT is a registered trademark of the International Mobile Satellite Organisation; the Inmarsat LOGO is a registered trademark of Inmarsat (IP) Company Limited. Both trademarks are licensed to Inmarsat Global Limited. Bluetooth is a trademark or a registered trademark of Bluetooth SIG Inc. and any use of such mark by Inmarsat is under licence. Microsoft Outlook, Microsoft Outlook Express, Microsoft Windows 10, Microsoft Windows 8, Microsoft Windows 7, Microsoft Windows XP Pro SP3 are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. Other product and company names mentioned herein may be the trademarks of their respective owners. Copyright Inmarsat Global Limited 2018. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 69 NOTICES The user is advised to erase personal data before disposing of the phone. Deleting data from the phone memory does not ensure that it cannot be recovered. Accordingly, Inmarsat does not warrant against recovery of information. Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 70 PROTECTION OF PERSONAL INFORMATION Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 71 Specification for product 71 Specification for unit Index 72 71 Specification for product MANUFACTURER PRODUCT TYPE / MODEL SPECIFICATION Battery Charger Inmarsat Phihong PSM10R-050 56426 702 098 3.7 V, 3180 mAh, 12 Wh, Li-ion Shenzen Honor Electronic Co Ltd ADS-6AE-06 05060E Car charger Tenwei Electronics Car adaptor Input = 100~240 V, 50/60 Hz, ~0.5A Output = 5 Vdc, 2 A MAX Input = 100~240 V, 50/60 Hz, 0.3Arms Output = 5 Vdc, 1.2 A MAX Input = 10-30 Vdc Output = 5 Vdc, 1.2 A Specification for unit UNIT Voltage Current Operating temperature Charging temperature SPECIFICATION Nominal battery voltage 3.7 V/900 mA 900 mA

-20C to +55C (-4F to +131F) 0C to +45C (+32F to +113F) Transmitter output power GMR2+

+33.5dBm 1626.5-1660.5MHz (normal band)

+31.0dBm 1668-1675MHz (extended band) Transmitter output power Bluetooth +6.2dBm 2400-2480MHz TYPE AND SPECIFICATION Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 72 A Accessories Admin code Alarm Cancelling Setting Silencing Any key answer Assistance button Activating an assistance button alert Assistance button security Configuring assistance button calls Configuring assistance button messages Enabling assistance button calling B Balance enquiry Barring calls Battery Charging Inserting Low battery alert Removing Bluetooth Connecting Lock Security Business card C Caller ID Sending Calls Barring Conference Declining Delete call logs Diverting Emergency From contacts From received message Handsfree Length Muting a call Receiving a call Receiving a second call Returning Summary Volume control While on another call Call waiting Setting Using Charger Car Mains Solar USB 65 54 44 44 44 23 36 36 35 35 35 34 24 11 10 11 10 50 51 51 43 24 24 19 17 23 25 19 16 31 21 22 21 17 18 17 23 21 17 24 18 11 11 11 11 INDEX Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 73 Closed user group Operating Code Admin PUK PUK 2 SIM PIN SIM PIN 2 User Conference calling Contact Calling a contact Creating Deleting Deleting all Duplicating Editing Emailing Finding Opening Ordering by first or last name Texting Copy SIM contacts to Phonebook CUG D Data Date and time settings Daylight saving time (DST) Disclaimer Display Customise settings Diverting Calls E eCompass function Finding a satellite Improving signal strength Emergency calling Export controls F Firmware version Fixed number dialling Activating De-activating Using G GPS Displaying in imperial Displaying in metric Fix National policies Obtaining a manual fix Satellite Sending your location Viewing your location Groups Add Assign ringtone Belongs to Members Remove Sending texts to View 51 54 55 55 55 55 54 19 42 41 42 42 42 42 42 41 41 41 42 43 51 45 48 49 64 49 25 15 15 19 66 13 26 26 26 39 39 15 39 39 14 39 38 32 32 32 32 32 32 32 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 74 H Handsfree calling I IMEI number IMSI number Incoming call alerting Configuring the incoming call alerting feature Missed incoming call alerts Receiving an incoming call alert Using incoming call alerting Info Important information IsatPhone Caring for K Keypad Changing Light Locking Volume L Language Phone Writing Local time zone setting Lock Bluetooth Keypad Phone Loud profile Loudspeaker M Mains charger Map Members Groups Messages Concatenation Create new Creating text for sending to email Delete Expiry period Forward Groups Receive Reply Service centre number Setting Validity Viewing received messages Message service centre number Microsoft Outlook Microsoft Outlook Express Minute counter Model My phone number N Number Re-dial Service provider Your phone number 21 12 12 21 20 20 20 12 59 48 49 50 46 47 48 49 51 50 50 46 21 11 8 32 33 29 30 32 33 31 32 30 31 33 33 33 31 33 9 9 22 12 44 17 44 44 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 75 P Pass code Call barring Personal alert Sending a personal alert Setting up and activating a personal alert Personalising settings Phone Language Lock Off On Upgrade Phonebook Managing contacts Phone language Setting Predictive text Setting Prepay Balance enquiry Voucher redemption Profiles General Loud Silent Vibrate only PUK 2 code PUK code R Received messages Save details Save message Re-dial Auto Remote time zone setting Reset all settings Ring mode Ringtones Assign to groups Unique S Satellite Screen Brightness Light Lighting Standby Security Admin code Network-controlled Phone-controlled SIM card-controlled SIM PIN 2 code SIM PIN code User code Service provider SIM card Copying Inserting Subscription SIM contacts Copying SIM PIN 2 code SIM PIN code 24 40 39 46 12 50 12 12 13 41 47 48 34 34 46 46 46 46 55 55 31 31 17 49 52 46 32 47 14 49 49 49 49 54 55 54 55 55 55 54 44 43 10 9 43 55 55 U User code V Vibrate only Voicemail Voucher redemption W World time Wrist strap Writing language 54 46 22 34 49 12 48 Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 72 A B C 73 C D E F G 74 H I J K L M N O 75 P Q R S 76 S T U V W X Y Z 76 Solar charger Sounds Ringtones Specification and type Speed dialling Removing Setting up Using T Texts Entering Predictive text Selecting standard or predictive mode Sending to group Standard text Time Daylight saving Time zone Local Remote Setting Tracking 11 46 71 23 23 23 28 28 29 32 29 49 49 49 49 Choosing the message interval 38 Choosing the message recipients and message type 37 37 Configuring tracking Starting tracking 38 38 Stopping tracking 37 Tracking feature Tracking security 38 56 71 Troubleshooting Type and specification Click to navigate 2 Welcome 3 Safety 6 Quick reference 9 Getting started 14 Using your IsatPhone 2 35 Location services 41 Phonebook & Contacts 45 Data 46 Personal settings 53 Security 56 Troubleshooting 59 Care and maintenance 61 Regulatory and compliance 64 Disclaimer 65 Accessories 66 Export controls 67 Malware 68 Downloading content 69 Notices 70 Protection of personal information 71 Type and specification 72 Index 77 inmarsat.com/isatphone While the information in this document has been prepared in good faith, no representation, warranty, assurance or undertaking (express or implied) is or will be made, nor will responsibility or liability (howsoever arising) be accepted by the Inmarsat group or any of its officers, employees or agents in relation to the adequacy, accuracy, completeness, reasonableness or fitness for purpose of the information in this document. All and any such responsibility and liability is expressly disclaimed and excluded to the maximum extent permitted by applicable law. INMARSAT is a trademark owned by the International Mobile Satellite Organisation licensed to Inmarsat Global Limited. All other Inmarsat trademarks in this document, including the Inmarsat LOGO, are owned by Inmarsat Global Limited. In the event of any conflict between the words of the disclaimer and the English version from which it is translated, the English version shall prevail. Inmarsat Global Limited 2018. All rights reserved. IsatPhone 2 User Guide (Model 2.1) May 2018.

29.09.2020 Minor Design change for IsatPhone 2 (Model 2.1) To whom it may concern, This letter is to notify you of a minor design change to the Isatphone 2 (Model 2.1). Due to End of Life (EOL) of the components used in the Low Noise Amplifier (LNA) on receiver path, the LNA will be replaced. The data sheet of the new LNA component is similar but not identical. Overall, the changes did not affect overall technical specification. The model name remains Isatphone 2 (Model 2.1). There is no impact to power (EIRP), spurious outputs or frequency stability compared to the previous LNA. Yours faithfully, Alison Horrocks Director Inmarsat Global Limited Alison.Horrocks@inmarsat.com Inmarsat Global Limited, 99 City Road, London, EC1Y 1AX, UK +44 (0)20 7728 1000 inmarsat.com Registered in England and Wales No. 3675885

1 Oct 2020 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Confidentiality Request FCC ID: YCT-ISATPHONE2W Dear Sir or Madame, Pursuant to Section 0.457 (d)(1)(ii) and 0.459 of the Commisions Rules, Inmarsat Global Ltd, hereby requests permanent confidential treatment of Information accompanying this application as outlined below:

Built of Materials Schematics PCB Top/Bottom Tune Up Procedure Internal Photos Inmarsat Global Ltd also hereby request short-short term confidential treatment of information accompanying this application as outlined below for a period of 180 days:

The above-mentioned materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might harmful to the Applicant and provide unjustified benefit to its competitors. The applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of grant of this Application. Yours sincerely, Alison Horrocks Director Inmarsat Global Limited Alison.Horrocks@inmarsat.com Inmarsat Global Limited, 99 City Road, London, EC1Y 1AX, UK +44 (0)20 7728 1000 inmarsat.com Registered in England and Wales No. 3675885