BM15_AN R2 BLE Single Mode Module Product Specification Model Name Project code Description Revision Issue Date BM15_AN R2 BLE Single Mode Module 1.4 2017/09/26 Approved by Harrison Chen Reviewed by Taka Wei Issued by Aaron Lai iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 Revision History Revision Released Date Comments/Remark 1.0 1.1 1.2 1.3 1.4 2017/03/07 2017/03/29 2017/06/07 2017/07/10 2017/09/26 Initial release Update reflow profile Update module photo and correct content typo Update GPIO pin 31 description and Reference Circuit Update ME drawing, layout and placement section Author Aaron Lai Aaron Lai Aaron Lai Aaron Lai Aaron Lai 2017 InnoComm Mobile Technology Corp. Disclaimer BM15_AN R2 BLE MODULE are supplied as is and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by InnoComm is believed to be accurate and reliable. InnoComm reserves the right to change specifications or product description in this document at any time without notice. Should Buyer purchase or use InnoComms products for any such unintended or unauthorized application, Buyer shall indemnify and hold InnoComm harmless against all claims and damages. InnoComm is the trademarks of InnoComm Mobile Technology Corp. Other trademarks and registered trademarks mentioned herein are the property of their respective owners. 2/19 InnoComm Mobile Technology Confidential TABLE OF CONTENT iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 INTRODUCTION ......................................................................................... 4 1. 2. GENERAL INFORMATION ........................................................................ 5 2.1 KEY FEATURES .................................................................................................... 5 2.2 BLOCK DIAGRAM ................................................................................................. 7 3. PIN MAP AND SIGNAL DESCRIPTION .................................................... 8 3.1 REFERENCE CIRCUIT .......................................................................................... 9 4. ELECTRICAL CHARACTERISTICS ........................................................ 10 4.1 RECOMMENDED OPERATING RANGE ............................................................. 10 4.2 POWER CONSUMPTION .................................................................................... 10 5. RF CHARACTERISTICS .......................................................................... 11 6. MECHANICAL INFORMATION ......................................................... .12 7. PCB LAYOUT RECOMMENDATION ...................................................... 13 8. MODULE PLACEMENT LAYOUT GUIDE............................................... 14 9. SMT SOLDER REFLOW RECOMMENDATION ..................................... 15 10.3 COMMUNITY RESOURCES .............................................................................. 17 10. PRODUCT AND DOCUMENTATION SUPPORT...................................16 10.1 DEVELOPMENT SUPPORT .............................................................................. 16 10.2 DOCUMENTATION SUPPORT .......................................................................... 17 Federal Communication Commission Interference Statement ................... 18 3/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 1. INTRODUCTION Based on TIs outstanding CC2640R2 BLE technology, Innocomms BM15_AN R2 module is a wireless microcontroller (MCU) targeting Bluetooth 4.2 and Bluetooth 5 low-energy applications. It is with very low active RF and MCU current and low-power mode current consumption provide excellent battery lifetime and allow for operation on small coin cell batteries and in energy-harvesting applications and embedded PCB antenna. BM15_AN R2 module contains a powerful 32-bit Cortex M3 running up to 48 MHz as the main processor and a rich peripheral feature set that includes a unique ultra-low power sensor controller. Bluetooth low energy controller and host libraries are embedded in ROM and run partly on an ARM Cortex-M0 processor. This architecture improves overall system performance and power consumption and frees up significant amounts of flash memory for the application. 4/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 2. General Information 2.1 Key Features RF 2.4-GHz RF Transceiver Compatible With Bluetooth low energy (BLE) 4.2 and 5 Specifications Supports data rates between 1 Mbps Programmable output power up to +5 dBm Excellent Receiver Sensitivity (97 dBm for BLE), Selectivity, and Blocking Performance Suitable for Systems Targeting Compliance With Worldwide Radio Frequency Regulations ETSI EN 300 328 (Europe) EN 300 440 class 2 (Europe) FCC CFR47 Part 15 (US) ARIB STD-T66 (Japan) Layout Few External Components 18.0 mm 10.5 mm 2.0 mm, 26 pin LCC Package Differential RF mode : 6.43 mA Differential RF mode TX at 0 dBm: 6.80.3 mA Differential RF mode TX at +5 dBm: 8.90.3mA Low Power Mode: 1 A (RTC Running + RAM/CPU retention) Low Power Mode: 100 nA (Flash retention) Low Power Wide supply voltage range : 1.9 3.8V Peripherals Integrated Temperature Sensor Four General-Purpose Timer Modules (Eight 16-Bit or Four 32-Bit Timers, PWM Each) 12-bit ADC, 200-ksamples/s, 8-Channel Analog MUX Ultra-Low-Power Analog Comparator UART 2x SSI (SPI, MICROWIRE, TI) Ultra-low power I2C, I2S Real-time clock AES-128 security module 15 GPIOs Support for 8 capacitive sensing channels Application Home and Building Automation Connected Appliances Lighting Locks Gateways Security Systems Industrial Logistics Production and Manufacturing Automation Asset Tracking and Management 5/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 HMI and Remote Display Access Control Retail Beacons Advertising ESL and Price Tags Point of Sales and Payment Systems Health and Medical Thermometers SpO2 Blood Glucose and Pressure Meters Weight Scales Hearing Aids Sports and Fitness Activity Monitors and Fitness Trackers Heart Rate Monitors Running and Biking Sensors Sports Watches Gym Equipment Team Sports Equipment HID Voice Remote Controls Gaming Keyboards and Mice 6/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 2.2 Block Diagram 7/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 3. PIN Map and Signal Description Pin #
Pin Name Direction/Type GND DIO_0 DIO_1 DIO_2 DIO_3 DIO_4 Power Digital I/O Digital I/O Digital I/O Description Ground GPIO, Sensor Controller GPIO, Sensor Controller GPIO, Sensor Controller, high-drive capability Digital I/O GPIO, Sensor Controller, high-drive capability Digital I/O GPIO, Sensor Controller, high-drive capability 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 JTAG_TMSC Digital I/O JTAG TMSC, high-drive capability JTAG_TCKC JTAG_TDO Digital I/O Digital I/O JTAG_TCKC GPIO, High drive capability, JTAG_TDO JTAG_TDI Digital I/O GPIO, High drive capability, JTAG_TDI GND GND Power Power Ground Ground nRESET Digital input Reset, active-low, with internal pull-up DIO_7 DIO_8 DIO_9 Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog DIO_10 Digital/Analog I/O GPIO, Sensor Controller, Analog DIO_11 Digital/Analog I/O GPIO, Sensor Controller, Analog DIO_12 Digital/Analog I/O GPIO, Sensor Controller, Analog DIO_13 Digital/Analog I/O GPIO, Sensor Controller, Analog DIO_14 Digital/Analog I/O GPIO, Sensor Controller, Analog VDD GND GND GND GND Power Power Power Power Power 1.9V to 3.8V main chip supply Ground Ground Ground Ground 8/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 3.1 Reference Circuit 9/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 4. ELECTRICAL CHARACTERISTICS 4.1 Recommended Operating Range PARAMETER Operating ambient temperature range, TA Operating supply voltage CONDITIONS For operation in battery-powered and 3.3V systems 4.2 Power Consumption MIN NOM MAX UNIT C 40 85 1.9 3.8 V Unless noted, all specifications are at 25 C and Vbat = 3.0 V. PARAMETER TEST CONDITIONS Low Power Mode (LPM4.5) Shutdown. No clocks running, no retention With RTC, CPU, RAM and (partial) register retention With DC/DC With DC/DC, 0 dBm output power With DC/DC, 5 dBm output power MIN 6.1 6.5 8.6 TYP 100 1 6.4 6.8 8.9 MAX 6.7 7.1 9.2 UNIT nA uA mA mA mA Low Power Mode (LPM3) Power consumption radio RX(2) Power consumption radio TX(2) Power consumption radio TX(2) 10/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 5. RF Characteristics 1 Mbps GFSK (Bluetooth low energy) Unless noted, all specifications are at 25 C, Vbat = 3.0 V and fRF = 2440MHz. PARAMETER RX Receiver sensitivity TX Output power, highest setting TX Output power, lowest setting Spurious emission 30-1000 MHz TEST CONDITIONS Differential mode, measured in 50 single-ended, BER=10-3 Differential mode, delivered to a single ended 50 load Delivered to a single ended 50 load Conducted measurement in a 50 single ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66 Spurious emission 1-12.75 GHz MIN TYP MAX UNIT dBm
-97
+5
-20 dBm dBm dBm dBm
-57
-47 Note: BM15_AN R2 module is with Internal bias mode design and related SW setting need to match with Internal bias mode. 11/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 6. Mechanical Information 12/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 7. PCB Layout Recommendation 13/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 8. Module Placement Layout Guide Placement Note: Please refer to BM15_AN Module_Placement guideline v1.0.pdf. Layout Note: Do not route any trace under module to avoid interference.
(O) (X) 14/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 9. SMT Solder Reflow Recommendation Note: Allowable reflow soldering times: 2 times base on recommended reflow profile. 15/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 10. Product and Documentation Support 10.1. Development Support TI offers an extensive line of development tools, including tools to evaluate the performance of the processors, generate code, develop algorithm implementations, and fully integrated and debug software and hardware modules. The following products support development of the CC2640 R2 device applications:
Software Tools:
SmartRF Studio 7 is a PC application that helps designers of radio systems to easily evaluate the RF-IC at an early stage in the design process. Test functions for sending and receiving radio packets, continuous wave transmit and receive Evaluate RF performance on custom boards by wiring it to a supported evaluation board or debugger Can also be used without any hardware, but then only to generate, edit and export radio configuration settings Can be used in combination with several development kits for Texas Instruments CCxxxx RF-ICs Sensor Controller Studio provides a development environment for the CC26xx Sensor Controller. The Sensor Controller is a proprietary, power-optimized CPU in the CC26xx, which can perform simple background tasks autonomously and independent of the System CPU state. Allows for Sensor Controller task algorithms to be implemented using a C-like programming language Outputs a Sensor Controller Interface driver, which incorporates the generated Sensor Controller machine code and associated definitions Allows for rapid development by using the integrated Sensor Controller task testing and debugging functionality. This allows for live visualization of sensor data and algorithm verification. Integrated development environment with project management tools and editor IDEs and Compilers:
Code Composer Studio:
Code Composer Studio (CCS) 7.0 and later has built-in support for the CC26xx device family Best support for XDS debuggers; XDS100v3, XDS110 and XDS200 High integration with TI-RTOS with support for TI-RTOS Object View IAR Embedded Workbench for ARM Broad debugger support, supporting XDS100v3, XDS200, IAR I-Jet and Segger J-Link RTOS plug in available for TI-RTOS For a complete listing of development-support tools for the CC2640 R2 platform, visit the Texas Instruments website at www.ti.com. For information on pricing and availability, contact InnoComm Mobile Technology Corporation sales office or authorized distributor. Integrated development environment with project management tools and editor IAR EWARM 7.80.1 and later has built-in support for the CC26xx device family Integrated development environment with project management tools and editor 16/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 10.2. Documentation Support To receive notification of documentation updates, navigate to the device product folder on ti.com
(CC2640R2F). In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. The current documentation that describes the CC2640R2F devices, related peripherals, and other technical collateral is listed in the following. Technical Reference Manual SWCU117 Technical Reference Manual. Texas Instruments CC26xx Family of Products 10.3. Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. TI Embedded Processors Wiki Texas Instruments Embedded Processors Wiki. Established to help developers get started with Embedded Processors from Texas Instruments and to foster innovation and growth of general knowledge about the hardware and software surrounding these devices. 17/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
-
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 18/19 InnoComm Mobile Technology Confidential iCOM_BM15_AN R2 Module Product Specification REV 1.4 9/26/2017 Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: Contains FCC ID: YAIBM15R2. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 19/19 InnoComm Mobile Technology Confidential