User Manual Product Family: K-Band Transceivers K-Band Transceiver with two integrated patch antennas IPM-165 (and variants IPM-165_UK / IPM-165_F) Description:
radar-based motion detector available in different frequency ranges:
Standard; _F and _UK variants Standard version selected by signal level advanced PHEMT-oscillator with low current consumption split transmit and receive path for maximum gain
- mono (single channel) operation
Environmental Tests and Handling Precautions:
very small outline dimensions This InnoSenT Sensor is sensitive to damage from ESD. Normal precautions as usually applied to CMOS devices are sufficient when handling the device. Touching the signal output pins has to be avoided at any time before soldering or plugging the device into a motherboard. Applying multimeters e.g. for resistance measurement between any of the connector pins may cause damage to the module.
Absolute Maximum Ratings:
Parameter supply voltage operating temperature (out of spec) storage temperature Electrical Characteristics:
Parameter transmit frequency output power (EIRP) temperature drift antenna pattern Tx (3dB) side lobe suppression IF output signal level*
Symbol fStandard fIPM-165_UK fIPM-165_F Pout Df horizontal vertical horizontal vertical voltage offset category A (low) category B or E
(medium) category C(high) VCC ICC tpulse TOP Symbol VCC TOP TSTG Rating 5.25
- 40 / + 85
+ 90 Units V C C typ. min. max. 24.000 24.125 24.250 24.150 24.200 24.250 24.075 24.125 24.175
-300 263 400 16
- 1 80 32 13 13 300 399 549 comment azimuth elevation azimuth elevation units GHz GHz GHz dBm MHz/C dB dB mV mVP-P mVP-P mVP-P supply voltage supply current Pulse length operating temperature outline dimensions
*Relative output signal level/voltage measured at room temperature in a dedicated InnoSenT test setup. compare drawing V mA s C mm 850 5.25 40
~ 25 x 25 x 7 (12.7) 5.0 30 10 550 4.75
+ 60
- 20 Version 7.4 2008-04-23 IPM-165 page 1 of 3 Interface:
The sensor provides a 2.54mm grid, single row pin header (square pin 0.635mm) In/Out Comment input output signal output input analog ground supply voltage (+5 V) Pin # Description 1 2 3 VCC IF1 GND Mechanical Outlines:
(all dimensions in mm) Approved pulsing conditions to fulfill the FCC requieremts:
ASK modulation with 10kHz and 10% dutycycle (on-time 10s min.) Warning: Any other pulsing condition with less than 10s on-time may void the FCC authorization to operate this equipment. Certification and environment protection:
InnoSenT GmbH has established and applies a quality system for:
Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances
(RoHs European Union directive 2002/95/EG). Version 7.4 2008-04-23 IPM-165 page 2 of 3 FCC approval This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. Manufacturers of mobile or fixed devices incorporating IPM-165 modules are authorized to use the FCC Grants and IC Certificates of the IPM-165 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS-IPM165F" and "Contains IC:
4012A-IPM165F". Contact Information:
InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0
+49 (0) 9528-9518-99 Fax:
E-Mail: info@InnoSenT.de Web: www.InnoSenT.de Version 7.4 2008-04-23 IPM-165 page 3 of 3