BT-Transceiver II Getting Started Copyright Copyright 2022 Accuver This manual is protected under international copyright laws. No part of this manual may be reproduced, distributed, translated, or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or storing is any information storage and retrieval system, without the prior written permission of Accuver. FCC Statement FCC Part 15C 15.247 is applied to the transmitter. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE (FCC Radiation Exposure Statement) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. BT-Transceiver II (ACX11X) Bluetooth Transceiver(BT-211M) Bluetooth Transceiver(BT-211M) LED Audio Port MOS . BT-Transceiver II (ACX11X) XCAL-Solo III , BT-Transceiver II (ACX11X) Bluetooth . 1 XCAL-Solo III MOS Kit, BT-Transceiver II
. 2 BT-Transceiver II . 3.5mm 4 poles LED
(USB C-Type) Accessories for Voice MOS Measurement Bluetooth 5.2
RF RF RF RF A2DP / AVRCP / HFP / SPP / aptX Voice SBC / AptX / AptX HD / AptX Adaptive DC +5V / 1A
+3.8V / 450mAh / 1.71Wh W28mm * D54mm * H24mm / 30g 2402 to 2480 MHz GFSK, /4 DQPSK, 8DPSK BDR 1Mbps / EDR 2,3Mbps BDR - 13dBm 1dB / EDR - 10 dBm 1dB Bluetooth LED
& (200ms)
(2.4s)
(2.4s) LED BT-Transceiver II (ACX11X) Bluetooth Transceiver(BT-211M) Bluetooth Transceiver(BT-211M) How to connect Bluetooth device name Charging LED It is used to measure MOS on a smartphone without Audio Port. For measurement, connect BT-Transceiver II (ACX11X) to XCAL-Solo III, and Bluetooth pairing between BT-Transceiver II (ACX11X) and smartphone. 1 Connect the MOS Kit, BT-Transceiver II wit h the XCAL-Solo III. 2 Pairing the Smartphone with the BT-Transceiver II. 3.5mm 4poles Audio Port Bluetooth LED Power switch Charging Port USB C-Type Accessories for Voice MOS Measurement Specification Bluetooth Version 5.2 Profile Codec Input Voltage Battery Size / Wight A2DP / AVRCP / HFP / SPP / aptX Voice SBC / AptX / AptX HD / AptX Adaptive DC +5V / 1A
+3.8V / 450mAh / 1.71Wh W28mm * D54mm * H24mm / 30g RF Frequency Band 2402 to 2480 MHz RF Modulation RF Data Rate RF Output Power Status Bluetooth LED Green & Red alternate quick(200ms) flash GFSK, /4 DQPSK, 8DPSK BDR 1Mbps / EDR 2,3Mbps BDR - 13 dBm 1dB / EDR - 10 dBm 1dB Stand-by Green flash Slowly(2.4s) Pairing Connect Red flash Slowly(2.4s) Pairing Disconnect Status Charging LED Green Red Charging Complete Charging Memo Accuver Americas Accuver EMEA Accuver Poland support.usa@accuver.com
+1 469 241 6100 support.emea@accuver.com
+44 203 457 4486 support.emea@accuver.com
+48 22 370 2518 www.accuver.com www.accuver.com www.accuver.com Accuver Japan Accuver APAC Accuver Shanghai inquiry.aj@accuver.jp
+81 3 6430 2580 support.apac@accuver.com
+852 2210 7004 support.apac@accuver.com
+86 187 0659 0330 www.accuver.jp www.accuver.com www.accuver.com Innowireless Korea Innowireless India sales@innowireless.com
+82 1899 1582 innoindia.support@innowireless.com
+91 224963 4902 www.innowireless.com www.innowireless.com