TRM Module Installation Guide Overview The TRM Module is a highly reliable, frequency hopping, spread-spectrum radio transceiver that operates within the 902 to 928 MHz license-free band. In order to ensure proper integration into the final product and maintain compliance with the rules and regulations under which this module has been granted certification, the requirements listed below must be followed. Compliance Requirements:
The TRM Module complies with FCC, Title 47, Chapter 1, Subchapter A, Part 15, Subpart C, Section 15.212
(a)(1)(i through viii). The final host/module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. Additional Compliance Information per FCC 47 CFR, Section 2.1077:
1. Product Identification TRM (Transmitter-Receiver Module) 2. The TRM module is in compliance with 47 CFR, Section 15.19(a)(3) as follows:
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3. Responsible party for Suppliers Declaration of Conformity:
a. Name of Responsible Party:
b. Address of Responsible Party: 397 S. Taylor Ave., Louisville, CO 80027 c. Telephone Numbers:
d. E-mail:
(800) 782-2709; (303) 939-9336 support@inovonics.com Inovonics Corporation
-
The TRM Module is intended only for use in products installed and maintained by professional security technicians.
- Manually test all TRM Module based products weekly. NOTE: It is Inovonics policy to maintain complete control of all firmware associated with this device. The TRM Module can operate only with the built-in antenna.
-
- When installed in a hosts end-device, the antenna must maintain a minimum separation distance of 20
-
cm from all persons. In accordance with FCC multi-transmitter product procedures, the TRM module must not transmit simultaneously with any other co-located antenna or transmitter.
-
The TRM Module does not contain any user serviceable components. A label must be affixed to the outside of the host product with the following statements:
-
10/16/19 357-00020-01 Rev A TRM Module Installation Guide Contains FCC ID: HCQ3B6T Contains IC ID: 2309A-T FCC and Industry Canada Compliance FCC Part 15 and Industry Canada Statements:
a. CFR 47 Part 15.19 Labeling Requirements Host product must bear the following in a conspicuous location on the device. This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. b. Part 15.21 Information to the user The users manual shall contain the following caution:
This device complies with part 15 of the FCC Rules, and any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC and Industry Canada RF Exposure Requirements The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC / IC RF exposure guidelines. IMPORTANT: The following statements must be included in the Users Manual:
FCC Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm during normal operation and must not be co-located or operating in conjunction with any other antenna or transmitter. 10/16/19 357-00020-01 Rev A TRM Module Installation Guide Industry Canada Statement:
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme avec ISED RSS-102 des limites d'exposition aux rayonnements dfinies pour un environnement non contrl. Cet metteur doit tre install au moins 20 cm de toute personne et ne doit pas tre colocalis ou fonctionner en association avec une autre antenne ou metteur. IMPORTANT: The End-Users Manual must include the appropriate language relating to the specific Class of Unintentional Radiation:
TRM 902-928 MHz ISM Band 2.5-5.5 Vdc 63 mW (18 dBm) Conducted
<3 dBi 100 mA, typical
<50 mA Frequency Hopping Spread Spectrum 25
-20C to +60C, non-condensing
<51 dBV/m Specifications Model #
Frequency Range Power Supply Tx Power Antenna Gain Tx Current Rx Current RF Technology Number of Hop Channels Operating Temperature Range Spurious Emissions (Worst Case) 10/16/19 357-00020-01 Rev A TRM Module Installation Guide TRM RF Module 0.562 1.312 Special Instructions The integrated antenna must not be tampered with; no connection to an alternate antenna is permitted. IMPORTANT NOTE: In the event that these conditions cannot be met, the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transceiver) and obtaining a separate FCC certification. When the module is installed inside another device and the FCC ID is not visible, the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label must use the wording described on the first page of this document. Manual Information To the End User The OEM integrator must not provide information in his Users Manual regarding the installation and / or the removal of the TRM module. The end user manual shall include all required regulatory information/warning as shown in this manual. Inovonics Wireless Contact Information If you have any problems with this procedure, contact Inovonics Wireless technical services:
Phone: (800) 782-2709; (303) 939-9336. E-mail: support@inovonics.com. 10/16/19 357-00020-01 Rev A