Ctrack by Inseego 9605 Scranton Road Suite 300 San Diego, CA 92121, USA
+1-858-812-3400 Ctrack NX35 Technical Manual DCT-MAN-296 CONFIG CONTROLLED This document is the confidential proprietary information of Ctrack by Inseego. Copyright in and ownership of this entire document and its contents rests with Ctrack by Inseego. No portion of or extract from this document may be reproduced, quoted or utilised for any purpose whatsoever without the prior written consent of Ctrack by Inseego. APPROVAL Revision 07 Date 21 August 2018 Author Gerhard Botha Reviewers Dirk Meintjies Approved by Jaco le Roux 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 TABLE OF CONTENTS 1. INTRODUCTION .................................................................................................. 7 1.1. Purpose of Document ................................................................................................................... 7 1.2. Applicable Documents ................................................................................................................. 7 1.3. NX35 Usage ................................................................................................................................... 7 2. SYSTEM OVERVIEW ........................................................................................... 8 2.1. Hardware Sub-systems ................................................................................................................ 8 2.2. High-level System Overview ........................................................................................................ 9 2.3. Block Diagram ............................................................................................................................... 10 2.4. Identification and Options ............................................................................................................ 11 3. EXTERNAL INTERFACES ................................................................................... 12 3.1. Wiring Connections and Connectors.......................................................................................... 12 3.2. Signal Description Main/Secondary Connector ...................................................................... 15 3.3. Environmental ............................................................................................................................... 16 3.4. Power ............................................................................................................................................. 16 3.5. Mechanical ..................................................................................................................................... 17 3.6. LEDS ............................................................................................................................................... 17 3.7. GNSS .............................................................................................................................................. 18 3.8. Cellular ........................................................................................................................................... 18 3.8.1. Option 1 - u-blox SARA-G350 Cellular Module ....................................................................... 18 3.8.2. Option 2 - u-blox LISA-U200 Cellular Module ......................................................................... 19 3.8.3. Option 3 - u-blox TOBY-L200 Cellular Module ........................................................................ 19 3.8.4. Option 4 - u-blox LISA-C200 Cellular Module ......................................................................... 20 3.8.5. Option 5 Sierra Wireless WP7504 Cellular Module .............................................................. 20 3.9. Bluetooth ...................................................................................................................................... 20 4. INTERNAL COMPONENTS ................................................................................. 21 4.1. Accelerometer ............................................................................................................................... 21 4.2. On-Board Memory ......................................................................................................................... 21 4.3. SIM Card Interface......................................................................................................................... 21 Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 2 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 4.4. Watchdog ....................................................................................................................................... 21 4.5. Internal Battery .............................................................................................................................. 21 5. REGULATORY COMPLIANCE STATEMENTS .................................................. 22 5.1. Federal communications Commission (FCC) Notice ................................................................ 22 5.2. Innovation Science and Economic Development (ISED) Notice .............................................. 22 5.3. FCC & ISED RF Exposure Guidance Satement .......................................................................... 23 INDEX OF FIGURES FIGURE 1 - BLOCK DIAGRAM FIGURE 2 - MAIN HARNESS FIGURE 3 MAIN CONNECTOR SIGNALS FIGURE 4 - SECONDARY HARNESS FIGURE 5 SECONDARY CONNECTOR SIGNALS FIGURE 6 - NX35 PICTURE 10 12 13 14 15 17 Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 3 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 DOCUMENT HISTORY Date Author Revision Description of Change(s) 23 June 2017 G Botha 01 First release 16 March 2017 G Botha 02 Add usage par 1.3 Add labels par 1.4 23 June 2017 G. Botha 03 Remove labels until final labels become available 28 September 2017 G. Botha 04 Add CDMA options R. Olmos Remove GSM and replace with Cellular Correct u-Blox Radio Module Models Listings Update Power Rating Information Add Regulatory Compliance Statements (Section 5.0) Add Block diagram. Change GPS to GNSS 02 October 2017 G. Botha 05 Change internal battery specification 10 October 2017 G Botha 06 Changed environmental (temperature) 21 August 2018 G Botha 07 Cosmetic changes change logo, company detail, some wording. Add WP7504 Sierra Wireless Modem as order option. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 4 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 DISCLAIMER Information provided in this manual is intended to be accurate and reliable. However, Ctrack by Inseego and its employees assume no responsibility for its use, nor for any infringements of rights of third parties which might result from its use. If this document is marked as Config Controlled and distributed via software, the signatures for preparing and release are archived by Ctrack by Inseegos Configuration Department. The responsibility is on the reader to ensure he has the latest revision of this document. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 5 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 ABBREVIATIONS AND DEFINITIONS The following words, expressions and abbreviations shall herein before and hereafter have the meanings ascribed to them unless inconsistent with the meaning of the requirement:
Direct current symbol (IEC 60417-5031 (2002-10)) DEFINITIONS GNSS Global Navigation Satellite System includes GPS, GLONASS, Galileo or BeiDou systems Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 6 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 1. INTRODUCTION 1.1. PURPOSE OF DOCUMENT This document provides technical detail of the Ctrack NX35 product platform. 1.2. APPLICABLE DOCUMENTS All referenced documents mentioned below can be requested from digicore_config@ctrack.co.za. Document Number Document Title DCT-PDS-023 Ctrack NX35 Product Specification DCT-MAN-300 Ctrack NX35 Installation Manual 1.3. NX35 USAGE The NX35 device is designed to accurately track position and other data of vehicles or assets and report this data to a data center. The NX35 is used to gather information relevant to fleet management services, to plot a vehicle position on a map and also follow the route taken by a vehicle during a journey. The position and speed of the vehicle is sampled using GNSS (Global Navigation Satellite System) and reported through a Cellular Modem data link with industry standard communication protocols. There are more device to vehicle interfaces available like digital I/O, analog inputs, pulse input, and other intelligent interfaces like serial and CAN J1939 to increase the data content about the vehicle. There are also interfaces to identify the driver of the vehicle to enable more fleet management functions and an internal accelerometer provides data for detecting how the vehicle is being driven, also known as driver behavior functions, as well as other vehicle movement detection. There are on-board resources like processor, memory and hardware watchdog. An internal battery provides power to the unit for a few hours when external power is lost. The device is fixed to a vehicle or asset during installation. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 7 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 2. SYSTEM OVERVIEW 2.1. HARDWARE SUB-SYSTEMS Load-dump and overvoltage protection Power supply and back-up battery charger Internal back-up battery GSM, WCDMA, LTE Cellular Option with SIM card (2nd optional SIM holder). CDMA Cellular Option with no SIM holder. GPS Module with external antenna and internal antenna fallback Interfaces o Discrete Inputs/Outputs o Analogue Input o Dallas One-wire interface o Serial (RS232) o Pulse input o CAN J1939 o Bluetooth Watchdog Real-time clock with battery back-up 3-axis Accelerometer RAM and Data flash Processor Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 8 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 2.2. HIGH-LEVEL SYSTEM OVERVIEW Manual DCT-MAN-296 The NX35 hardware platform can be used for the Ctrack fleet products (Fleet Light, Assist and Solo) Uses state of the art 32-bit microprocessor technology and flash device for non-volatile storage. Latest Cellular Modem with internal antenna for communication. Provision is made to populate a 2G, 3G, or 4G Cellular Modem. Internal antenna solution supported. GNSS with external antenna and antenna tamper technology for accurate position and online/offline assisted GPS. Provision is made for fall-back to an internal antenna. A 3-axis Accelerometer for movement detection, harsh driving events and severe G-force vehicle manoeuvres for accident detection. Daily Health Checks Digital inputs and outputs. One input can be used for pulse detection. Combination input for panic and business/private trip detection. Analogue input Buzzer and immobilisation outputs. One wire driver identification input. Power supply input with internal back-up battery. Power down modes to save battery power External interfaces for installation, maintenance and other peripherals (e.g. driver behaviour indicator). Internal Bluetooth interface. Extra slot for future product expansion. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 9 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 2.3. BLOCK DIAGRAM Pwr / Gnd 4 Digital In In 1-4 Ext 2 Digital Out 1-2 Ext 1 Multi In Bus/Priv/Panic 1 Dallas 1 Wire 1 RS232 Uart 1 Ignition In (ACC) 1 Digital In In 5 Ext 1 Digital Out 3 Ext 1 RS232 Uart 1 Analog In Ext CAN HS CAN LS r o t c e n n o C y r a m i r P r o t c e n n o C y r a d n o c e S r o t c e n n o C n o s n a p x E i r o t c e n n o C g u b e D GNSS uBlox M8030 Xtl Switch Antenna
(Int) Rf Conn
(Ext) External RAM Ext LEDs Antenna (Int) SIM LED Antenna Rst Sw Reset gen Cellular Radio Module Processor RF EEPROM RTC WDT Accelerometer Power Management Charging Circuitry Battery FIGURE 1 - BLOCK DIAGRAM Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 10 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 2.4. IDENTIFICATION AND OPTIONS Manual DCT-MAN-296 Model Number Integrated Cellular Radio Module NX35-G350 NX35-U200 NX35-L200 NX35-C200 SARA-G350 Cellular Modem (2G) LISA-U200 Cellular Modem (3G) TOBY-L200 Cellular Modem (LTE) LISA-C200 Cellular Modem (CDMA) NX35-L7504 WP7504 Sierra Wireless Cellular Modem (3G/4G) Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 11 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 3. EXTERNAL INTERFACES 3.1. WIRING CONNECTIONS AND CONNECTORS Manual DCT-MAN-296 FIGURE 2 - MAIN HARNESS Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 12 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 FIGURE 3 MAIN CONNECTOR SIGNALS Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 13 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 FIGURE 4 - SECONDARY HARNESS Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 14 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 FIGURE 5 SECONDARY CONNECTOR SIGNALS 3.2. SIGNAL DESCRIPTION MAIN/SECONDARY CONNECTOR The following tables describes the signals with reference to Figure 2 - Main Harness to Figure 5 Secondary Connector Signals. Plug Main Main Main Main Main Main Main Sec Main
-
Sec SIGNAL DESCRIPTION
+VIN GND
+VOLTAGE INPUT 6-32VDC POWER GND IGN_IN_EXT IGNITION SENSE - Active High Digital Input IN1_IN_EXT INPUT 1 - Active Low Digital Input IN2_IN_EXT INPUT 2 - Active Low Digital Input IN3_IN_EXT INPUT 3 - Active High Digital Input IN4_IN_EXT INPUT 4 - Active High Digital Input IN5_IN_EXT INPUT 5 Can be used as active low digital input or pulse input
(7KHz maximum pulse) OUTPUT1_EXT DIGITAL OUTPUT1 Immobilizer Output (Open collector) OUTPUT2_EXT DIGITAL OUTPUT2 Buzzer Output OUTPUT3_EXT DIGITAL OUTPUT2 Auxiliary Output (Open collector) Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 15 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 BUS/PRIV_IN_EXT BUSINESS / PRIVATE / PANIC INPUT BUS/PRIV_GND BUSINESS / PRIVATE / PANIC GROUND 1-WIRE_IN DRIVER ID 1 WIRE INPUT COMMS_TXD Serial Port 1 RS232 Transmit COMMS_RXD Serial Port 1 RS232 Receive COMMS_GND Serial Port 1 RS232 GND COMMS2_TXD Serial Port 2 RS232 Transmit COMMS2_RXD Serial Port 2 RS232 Receive COMMS2_GND Serial Port 2 RS232 GND ANA_IN_EXT ANALOGUE INPUT (0-12Volt) CANH_HS High Speed CAN H Signal CANL_HS CANH_LS CANL_LS High Speed CAN L Signal Low Speed CAN H Signal Low Speed CAN L Signal CAN_GND CAN GND Main Main Main Main Main Main Sec Sec Sec Sec Sec Sec Sec Sec Sec 3.3. ENVIRONMENTAL Certifications E-Mark, CE-Mark, PTCRB, Australian Operating Temperature (operating) Operating Temperature (storage) Operating Humidity
-20 to 60 oC
-20 to 60 oC 95%
3.4. POWER Input Voltage Internal Battery 6-32 Vdc 3.6-4.2 Vdc Normal Operation GSM Option +
maximum battery charging
<1A Normal Operation CDMA Option +
maximum battery charging
<1A Sleep Mode
<1 mA Sleep Mode + maximum battery charging
< 500mA Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 16 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 3.5. MECHANICAL Dimensions: 131 x 73 x 29mm Weight: ~ 150g FIGURE 6 - NX35 PICTURE 3.6. LEDS LED Function Pattern and function 1-Green Install State On- Reading install state Flash User installation input required 2-Red GNSS 3- Yellow Heartbeat 4- Red Cellular 5-Green Bluetooth 6-Red File system
. Off Ready (see *note) On GNSS on and unlocked Fast flash 2D lock Slow flash 3D lock Off GNSS switched off (see *note) Flash Firmware running On Firmware busy rebooting Off- Cellular off or no service Blip/flashing- Registered on network On- Data transmit in progress Off- BT disabled or off (see *note) On- BT on Slow flash- BT Discoverable mode Fast flash- Call in progress On when FFS is accessed Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 17 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296
*Note: 10Minutes after the unit has been finalised and the install tool disconnected, all LEDS will switch off for security reasons. To switch on the LEDs again, connect an install tool. 3.7. GNSS Part u-blox M8 engine GPS Receiver 72 channels, GPS/QZSS L1 frequency C/A Code, GLONASS L10F, BeiDou B1, Galileo E1B/C. SBAS L1 C/A; WAAS, EGNOS, MSAS, GAGAN Time to first fix Cold start: 26s Aided start: 2s Hot start: 1s Accuracy GPS/SBAS/QZSS+GLONASS : 2m Multi-GNSS Assistance AssistNow Online AssistNow Offline AssistNow Autonomous Anti-jamming Active CW detection and removal Antenna External antenna with internal antenna fall-back. Antenna part example (DAM1575A4I10_K3M) External antenna assembly shown below:
3.8. CELLULAR The hardware layout makes provision for populating the following Cellular Modem types:
1. u-blox SARA-G350 (2G) 2. u-blox LISA-U200 (3G) 3. u-blox TOBY-L200 (LTE) 4. u-blox LISA-C200 (CDMA) 5. Sierra Wireless WP7504 (3G/4G) 3.8.1. Option 1 - u-blox SARA-G350 Cellular Module Quad band support GSM 850/900/1800/1900 MHz Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 18 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 GPRS GPRS Class 10, CS1-CS4 up to 85.6 kb/s. PBCCH support Circuit Switched Data Up to 9.6 kbps Encryption algorithms A5/1 supported for GSM and GPRS modes SMS Mobile-originated and mobile-terminated SMS supported. Text and PDU modes supported GSM Jamming detection Supported 3.8.2. Option 2 - u-blox LISA-U200 Cellular Module GSM band support GSM 800/850/900/1700/1900/2100 MHz GPRS EDGE GPRS Class 12, CS1-CS4 up to 85.6 kb/s. Class 12, MCS1-9 Circuit Switched Data GSM Up to 9.6 kbps Encryption algorithms A5/1 supported for GSM and GPRS modes SMS Mobile-originated and mobile-terminated SMS supported. Text and PDU modes supported GSM Jamming detection Supported 3.8.3. Option 3 - u-blox TOBY-L200 Cellular Module LTE band support 2,4,5,7,17 (N America) UMTS GSM SMS 850/900/AWS/1900/2100 850/900/1800/1900 Mobile-originated and mobile-terminated SMS supported. Text and PDU modes supported GSM Jamming detection Future Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 19 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 3.8.4. Option 4 - u-blox LISA-C200 Cellular Module Manual DCT-MAN-296 CDMA band support 800, 1900 MHz (Sprint, Verizon) SMS Mobile-originated and mobile-terminated SMS supported. Text modes supported Cellular Jamming Future detection 3.8.5. Option 5 Sierra Wireless WP7504 Cellular Module CDMA band support LTE (B2, B4, B5, B12, B17, B25, B26) UMTS (B2, B4, B5) CDMA, EVDO (BC0, BC1, BC10) Cellular Jamming Future detection 3.9. BLUETOOTH The unit has an on-board Bluetooth with the following major features:
Device BCM20706 (Broadcom), (A2DP, SPP, GATT) Bluetooth Specifications Bluetooth v4.2 + EDR with integrated Class 1 PA Integrated RF Single-ended, 50-ohm RF interface Built-in TX/RX switch Tx class 1 or class2 output power capable RX sensitivity basic rate of -93.5 dBm RX sensitivity for Low Energy of -96.5 dBm Max Transmit Power
< 12 dBm BT Low Energy Supported Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 20 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 4. INTERNAL COMPONENTS 4.1. ACCELEROMETER Manual DCT-MAN-296 An on-board 3-axis 8g accelerometer is used for various movement-detection functions:
1. Vehicle movement 2. Roll over and device tamper 3. Severe and High G-force 4. Harsh driving (acceleration, braking, cornering and up/down) 4.2. ON-BOARD MEMORY The on-board memory is as follows:
16 MByte Parallel NOR flash for file system 4 Mbyte RAM 16 Kbit NFC EEPROM for storage of default settings. 4.3. SIM CARD INTERFACE On-board SIM card reader with protection and supports 1V8 and 3V SIM cards. An optional second SIM is provided on the board for future use.
(Not supported for CDMA option.) 4.4. WATCHDOG On-board hardware watchdog circuitry to ensure continuous system operation under all conditions. 4.5. INTERNAL BATTERY
- Uses single Li Polymer 1100mAH battery
- Supplies power to the electronics when external power is removed.
- Automatically charged when external power is connected
- Battery protection consist of over-voltage, under-voltage and over-current. Additional over-temperature protection is provided by the charger in conjunction with the built-in battery thermistor. The battery cannot be charged when its temperature is over 55 deg C. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 21 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual 5. REGULATORY COMPLIANCE STATEMENTS Manual DCT-MAN-296 5.1. FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications made to this device that are not expressly approved by Ctrack may void your authority to operate the equipment. 5.2. INNOVATION SCIENCE AND ECONOMIC DEVELOPMENT (ISED) NOTICE This device complies with Industry Canadas Licence-Exempt RSSs. Operation is subject to the following two conditions:
This device may not cause interference; and This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
lappareil ne doit pas produire de brouillage;
Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 22 of 23 9605 Scranton Road Suite 300, San Diego, CA 92121, USA Ctrack by Inseego Ctrack NX35 Technical Manual Manual DCT-MAN-296 lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 5.3. FCC & ISED RF EXPOSURE GUIDANCE SATEMENT In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit tre install pour fournir au moins 20 cm de sparation du corps humain en tout temps. Revision: 07 21 August 2018 COMPANY CONFIDENTIAL Ctrack by Inseego Page 23 of 23