FCC ID: 2AYS7-MARK1 Vision MARK-1

USER GUIDE Contents Overview.........................................................4 Getting Started with the Vision MARK-1.....7 1. Charge the Device................................7 2. Turn ON the Device..............................7 3. Unlocking the Screen...........................8 4. Connect to Wi-Fi....................................9 5. Sign in to the Organization Portal with Insitucloud Account........11 6. Install a Materials App.......................12 7. Ready to Make Measurements.........13 Getting to Know Your Device......................14 1. Status Bar and Navigation Bar.........14 2. Basic Gestures....................................15 3. Turn OFF or RESTART the Device.....15 4. Plugging in an Insight Module..........15 Using Apps.....................................................16 1. Finding Apps.......................................16 2. Switch Between Recently Used Apps.....................................................17 3. Close Apps..........................................17 4. Adding an App to the Home Screen..................................................19 5. Move or Remove Home Screen Apps.....................................................20 Change Your Settings...................................21 1. Quick Settings.....................................21 2. Change the Brightness......................22 3. Battery.................................................22 4. Change the Volume............................24 5. Additional Settings.............................24 Safety Precautions.......................................25 Regulatory Notices.......................................28 Overview The Vision MARK-1 performs rapid materials assessments on location and during materials use which allows for better control, helps to prevent materials defects, and improves overall quality in a manufacturing process. Note: In order to make materials measurement on the device, the Vision MARK-1 needs a specific Insight module and materials probe that correspond to the materials being measured. 4 Front LED Status Indicator

(RYG) Insight Port Power Button Volume Control The Vision MARK-1 performs rapid materials assessments on location and during materials use which allows for better control, helps to prevent materials defects, and improves overall quality in a manufacturing process. Note: In order to make materials measurement on the device, the Vision MARK-1 needs a specific Insight module and materials probe that correspond to the materials being measured. Charging Port 5 Back Lanyard Straps Humidity Sensor 6 Getting Started with the Vision MARK-1 1. Charge the Device Before using the Vision MARK-1, plug in the power cord and fully charge it. 2. Turn ON the Device To turn ON the Vision MARK-1, press and hold the power button for a few seconds and you will see the Insituware logo appear on the screen. 7 3. Unlock the Screen To unlock the screen, swipe your finger up from the bottom of the screen. To lock the screen, press the power button once. 8 4. Connect to Wi-Fi From the Home screen tap the Settings app. Tap Network & Internet. 9 Toggle the button to turn Wi-Fi on, then select a listed network. Enter the network password (if applicable) to finish connecting to Wi-Fi. 10 5. Sign in to the Organization Portal with Insitucloud Account From the Home screen, tap the Organization Portal app. Log in with your Insitucloud credentials. Note: If you do not already have an Insitucloud account, tap the Sign Up tab in the Organization Portal app or go to portal.insituware.com to create an account. 11 Once logged in, select your Organization. 6. Install a Materials app In the Organization Portal app, under Applications select the Materials app you would like to install and tap Install. Note: If there is an app update, it will say Update instead of Install. 12 Once logged in, select your Organization. 7. Ready to Make Measurements Now you are ready to make measurements with the Vision MARK-1!

Note: For more information on using Materials apps, Insights, and probes with the Vision MARK-1, visit support.insituware.com. 6. Install a Materials app In the Organization Portal app, under Applications select the Materials app you would like to install and tap Install. 13 Getting to Know Your Device Status Bar Time Wi-Fi Battery Life Back Home Overview Navigation Bar 14 Basic Gestures Tap to select or open something on your device like a button or an app. Tap and hold to move apps around or occasionally access other options (think of this as right-clicking). Swipe to scroll up and down, left and right, or any other direction on the screen. Turn OFF or RESTART the Device To turn OFF or RESTART the Vision MARK-1, press and hold the power button on the side until the options to Power Off and Restart appear on the screen. Plugging in an Insight Module Use the guides on the side of the Insight module to slide it into the Vision MARK-1 device and connect it in place. You will know it is connected when you can feel and hear the Insight module click into place. 15 Using Apps Finding Apps To search for apps, swipe up on the screen to access All Apps. Use the search bar to type in the name of the app you are looking for, or search through the apps below. 16 Finding Apps Switch Between Recently Used Apps Tap the Overview button ( ) on the Navigation Bar to show all open apps. To search for apps, swipe up on the screen to access All Apps. Swipe left or right to go to the app you want and tap it. Use the search bar to type in the name of the app you are looking for, or search through the apps below. Close Apps Close one app: While viewing open apps, swipe up on the app you want to close. 17 Close all apps: While viewing open apps, swipe right until you see Clear All. Tap Clear All to close all open apps. 18 Close all apps: While viewing open apps, swipe right until you see Clear All. Tap Clear All to close all open apps. Adding an App to the Home Screen Find the app you want to add to the Home screen. Tap and hold the app (dont release yet), and start dragging across the screen where you will be taken to a special view of the Home screen. Continue to hold the app while you decide where to put it. Release the app once youve chosen a spot, and it will be added to your Home screen. 19 Move or Remove Home Screen Apps On the Home screen, tap and hold the app you want to move or remove. To move it, drag and drop the icon to a new location. To remove it, drag the icon to the Remove option. To uninstall it from the device, drag the icon to the Uninstall option. Note: This wont delete the app from your device. It will only remove the shortcut from the Home screen. 20 Change Your Settings Quick Settings Swipe down on the Status Bar to open the Notification Drawer and access quick settings and notifications. Swipe down again on the Notification Drawer to reveal the expanded view, to show additional details. 21 Change the Brightness From the Notification Drawer tap and hold the star icon left or right to change the brightness of the screen. Battery Battery Saver: From the Notification Drawer tap the Battery Saver icon, then select Turn On. 22 Change the Brightness From the Notification Drawer tap and hold the star icon left or right to change the brightness of the screen. Battery Percentage: From the Settings app tap Battery. Toggle Battery Percentage and you will now see the percentage in the Status Bar. Battery Battery Saver: From the Notification Drawer tap the Battery Saver icon, then select Turn On. 23 Change the Volume Use the volume buttons on the side of the device to turn the volume up (+) or down (-). Additional Settings Go to the Settings app to view additional settings. 24 Safety Precautions Note: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in the manual. WARNING Do not insert liquids or foreign objects. Penetration of liquids or foreign objects could result in fire or electrical shock. If liquids or foreign object should enter the device, immediately turn it off, disconnect the charging cord from the power outlet (if charging) and contact Insituware at support. insituware.com. Do not place the device near water (ex. a sink, washing stations, etc.). Do not expose the device to rain or moisture. Do not place the device outdoors. Do not place metals, combustibles, etc. on or around the device. To avoid penetration of foreign objects, place the device in its provided secure case when traveling and do not put together with anything except the included accessories. Never disassemble and/or modify. Modification and/or disassembly of the device or accessories could result in fire or electrical shock. Do not attempt to dissassemble the device or take it apart in any way. Contact Insituware to repair and/or clean inside. Do not give the device any shock or impact. If the device should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical 25 Additional Settings Go to the Settings app to view additional settings. shock. If the device is shocked, immediately turn it off, disconnect the charging cord from the power outlet (if charging) and contact Insituware at support.insituware.com. Do not place the device on an unstable surface. If the device should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. Do not place the device on an unstable, slanted, or vibrating surface such as a wobbly or inclined stand. Use only the correct power cord and the correct power outlet. Incorrect power supply could result in fire or electrical shock. Use only charging devices approved by Insituware. Inistuware accessories are designed for your device to maximize battery life. Using other accessories may invalidate your warranty and may cause damage. Be cautious of the charging cord connection. Incorrect connection of the power cord could result in fire or electrical shock. Do not touch the charging cord with a wet hand. Check that the connecting portion of the charging cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug. Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet to prevent contact failure. Avoid extreme temperature environments. The heat or cold could have adverse influence on the device. Do not place the device, or 26 shock. If the device is shocked, immediately turn it off, disconnect the charging cord from the power outlet (if charging) and contact Insituware at support.insituware.com. Do not place the device on an unstable If the device should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical surface. shock. Do not place the device on an unstable, slanted, or vibrating surface such as a wobbly or inclined stand. Use only the correct power cord and the correct power outlet. Incorrect power supply could result in fire or electrical shock. Use only charging devices approved by Insituware. Inistuware accessories are designed for your device to maximize battery life. Using other accessories may invalidate your warranty and may cause damage. Be cautious of the charging cord connection. Incorrect connection of the power cord could result in fire or electrical shock. Do not touch the charging cord with a wet hand. Check that the connecting portion of the charging cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug. Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet to prevent contact failure. Avoid extreme temperature environments. The heat or cold could have adverse influence on the device. Do not place the device, or other accessories near a hot object such as heater, or cold objects such as a refrigerator, etc. Body worn operations. For body worn operations, this Vision MARK-

1 has been tested and meets the FCC &

ISED RF exposure guidelines for use with an accessory that contains no metal and the positions the Vision MARK-1 a minimum of 0 cm from the body. Use of other accessories may not ensure compliance with FCC & ISED RF exposure guidelines. The highest SAR value for the Vision MARK-1 as reported to the FCC and ISED when tested for use at the body is 0.774W/kg and 0.907W/kg. Proper Disposal This product contains a 5000 mAh Lithium Polymer battery; do not put in trash. Dispose of in accordance with environmental laws. For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, contact Insituware. 27 Regulatory Notices FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Operation of this device in the 5150-5250 MHz band is restricted to indoor use only. CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. 28 Regulatory Notices FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Operation of this device in the 5150-5250 MHz band is restricted to indoor use only. CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/

TV technician for help. This equipment has been tested and meets applicable limits for radio frequency (RF) exposure. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter. For body worn operations, this Vision MARK-

1 has been tested and meets the FCC &

ISED RF exposure guidelines for use with an accessory that contains no metal and the positions the Vision MARK-1 a minimum of 0 cm from the body. Use of other accessories may not ensure compliance with FCC & ISED RF exposure guidelines. The highest SAR value for the Vision MARK-1 as reported to the FCC and ISED when tested for use at the body is 0.774W/kg and 0.907W/kg. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Canadian Compliance Statement NOTICE: This Class B digital apparatus complies with Canadian ICES-003. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada license-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, 29 including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: Afin dassurer la conformit aux exigences de la FCC en matire dexposition aux radiofrquences, aucune modification de lantenne ou de lappareil nest autorise. Toute modification de lantenne ou de lappareil pourrait avoir pour consquence que lappareil dpasse les exigences en matire dexposition aux radiofrquences et annule le droit de lutilisateur de faire fonctionner lappareil. 30 including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: Afin dassurer la conformit aux exigences de la FCC en matire dexposition aux radiofrquences, aucune modification de lantenne ou de lappareil nest autorise. Toute modification de lantenne ou de lappareil pourrait avoir pour consquence que lappareil dpasse les exigences en matire dexposition aux radiofrquences et annule le droit de lutilisateur de faire fonctionner lappareil. 31 Take Control insituware.com Form No. INSM5001R1 | 2021 Insituware

C5266091_X10_Ed.1 Insituware LLC 107 Gilbreth Pkwy, Suite #202, Mullica Hill, NJ 08062 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: April 19, 2021 Subject: Request for Confidentiality FCC ID: 2AYS7-MARK1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No No Short-Term Confidentiality No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Christopher Frederickson Title: Director of Engineering 1/1

C5266091_X8_Ed.1 Insituware LLC 107 Gilbreth Pkwy, Suite #202, Mullica Hill, NJ 08062 Letter of Authorization Company: Insituware LLC Address: 107 Gilbreth Pkwy, Suite #202, Mullica Hill, NJ 08062 Product Name: Vision MARK-1 Model Number: Vision MARK-1 FCC Identifier: 2AYS7-MARK1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Christopher Frederickson Title: Director of Engineering Date: April 282021 Signature of applicant:

1/1

C5266091_X13_Ed.1 Insituware LLC 107 Gilbreth Pkwy, Suite #202, Mullica Hill, NJ 08062 FCC Software Configuration Control Declaration Date: April 28, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: Vision MARK-1/Vision MARK-1 Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Signature of applicant Name: Christopher Frederickson Title: Director of Engineering 1/1

Tune-up procedure Each device is individually calibrated during manufacturing. Measurement is performed in a full calibrated setup using Wideband Radio Communication Tester or spectrum analyzer and power meter. Measurement procedure is outlined below:

1. Set the device to operational voltage and on a predefined band class and 2. The WIFI specific RF characteristics were measured by spectrum analyzer channel. and power meter. The user has no possibility to change these settings. Tune up procedure shall be over the power range or at specific operating 1. It must provide an operational voltage to turn on the device and on one certain channel in service mode by means of company proprietary 2. The maximum gains of each individual device are adjusted until the target power levels. software. value met. Conducted Power Table 2.4G WLAN Band 2.4GHz WLAN Mode 802.11b 802.11g 802.11n HT20 Target Power (dBm) Tolerance (dB) 7.50 8.50 7.50

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5) Mode LE Target Power (dBm) Tolerance (dB) 1.50

(-1.5,+0.5) Band Mode Tolerance (dB) Target Power

(dBm) BT Band BT 5G WLAN 5.2GHz WLAN 5.3GHz WLAN 5.6GHz WLAN 5.8G WLAN 802.11a 802.11n HT20 802.11n HT40 802.11ac VHT20 802.11ac VHT40 802.11ac VHT80 802.11a 802.11n HT20 802.11n HT40 802.11ac VHT20 802.11ac VHT40 802.11ac VHT80 802.11a 802.11n HT20 802.11n HT40 802.11ac VHT20 802.11ac VHT40 802.11ac VHT80 802.11a 802.11n HT20 802.11n HT40 802.11ac VHT20 8.50 8.50 9.00 8.00 9.00 7.50 8.50 8.50 8.50 8.00 8.50 7.00 6.50 6.50 6.50 5.50 6.00 5.00 6.50 6.50 7.00 6.00

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5)

(-1.5,+0.5) 802.11ac VHT40 802.11ac VHT80 7.00 5.50

(-1.5,+0.5)

(-1.5,+0.5)