ENGLISH Charge the Tablet The Tablet comes with a built-in rechargeable lithium-polymer battery. It is recommended to fully charge the battery before first use. To charge the Tablet, plug the charger to an electrical socket with the other end of the adapter inserted to the microUSB input slot on the Tablet (Refer to Step 1 on the previous page). You may continue to use the Tablet while it is charging. You may stop charging any time even when it is not 100% charged. If the Tablet is powered on, the battery charge status will be indicated at the top right corner of the screen by the battery meter. If the Tablet is powered off, it will charge until the battery is full. When the battery life runs out, the battery meter turns red and the device needs to be charged soon. It will continue to operate as usual until it drops to 0%. Disconnect the power adapter when the Tablet is fully charged. Note: When the Tablet is connected to a computer via the USB cable, the battery will charge via the USB socket, but at a much slower rate than the power adapter supplied. Do not use any other power adapters than the one supplied. Using an incompatible power adapter could damage the tablet and poses the potential risk of fire. Turn on the Tablet Press the power key circled in red for 5 seconds. Wait for about 30 seconds for Android to load and start. The Tablet will guide you through the basic setup. Initial setup On the welcome page, scroll to select the desired language. Tap the arrow circled in green to proceed. Select a Wi-Fi network, i.e. the wireless network for Internet connection Enter the password and wait for the connection and system check. It may take up to 2 minutes. Sign in to your Google account If you have an existing Google account Enter your Google email and press Next Enter your Google account password and press Next Accept the Terms of Service and Privacy Policy If you do not have a Google account yet Select Or create a new account Enter you first name and last name and press Next 7 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC STATEMENT This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1)
(2) undesired operation of the device. This device may not cause interference; and This device must accept any interference, including interference that may cause Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC SAR warning:
The information listed above provides the user with information needed to make him or her aware of a RF exposure, and what to do to assure that this radio operates within the RSS exposure limits of this radio. The device complies with RF specifications when the device used at 5mm from your body. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.