Multi Prox Proximity Card and Pin Reader Installation Manual PUBLICATION INFORMATION 60A9 - Draft Release Version 0.1.2 71D0 - Version 1.0.5 CONTENTS Introduction................................................... 1 Legend........................................................................ 2 Terminology ................................................................ 2 Mounting........................................................ 4 Wiegand Connection ...................................... 5 Aux Button Input ........................................... 7 Programming ................................................. 8 Entering Programming Mode .......................................... 8 Address Selection ......................................................... 9 Data Programming ..................................................... 10 Standalone Operation .................................. 18 Programming Users .................................................... 18 Super User Mode ........................................................ 18 Specification ................................................ 19 Warranty...................................................... 20 1.0 INTRODUCTION INTRODUCTION Thank you for choosing the Multi Prox Proximity and Pin Reader from Integrated Control Technology. The Multi Prox Proximity and Pin Reader is an advanced technology radio frequency identification device (RFID) specifically designed to enhance the functionality of security, building automation and access control by providing independent multiple format compatibility for both card and pin, high speed data transmission, built in Standalone operation and sabotage protection. The Multi Prox Proximity and Pin Reader is designed to operate as a Normal Wiegand Proximity and Pin Reader or as a complete Standalone Single Door Controller. The Multi Prox Proximity and Pin Reader can be programmed to perform and operate using independent card and pin output formats. Therefore, before installing the Multi Prox Proximity and Pin Reader, we highly recommend you read this manual carefully and ensure that the formats you program will operate with the configured access control or security product. When operating the Multi Prox Proximity and Pin Reader in Standalone mode you must use the Nano Prox Access Manager Application which allows a personal computer to perform user programming and configuration. For more information on the Multi Prox Proximity and Pin Reader and other Integrated Control Technology products please login to www.integratedcontroltechnology.com 1 Multi Prox Proximity Reader and Pin Installer Manual LEGEND Indicates a warning or advisory message relating to the section or location. Indicates a hint or suggestion that relates to the section or location.
[TEXT] Bold text enclosed in brackets is used to show a section number or address of a programmable option or information on programming shortcut sequences. Italics Italic text shows a reference to a section or page. TERMINOLOGY To ensure that you program the Multi Prox effectively please familiarize yourself with the following terms used throughout this manual. Wiegand The data transmission method used to communicate data to a controller or reader expansion device. Data is sent on a D0 (Data 0) and D1 (Data 1) interface in an open collector connection. Programming Card The Nano Prox Series of readers utilize built in programming functions that allow many options to be configured. To program these options you must have a Programming Card. These are typically marked with the text ICT Programming Card in place of the normal facility code and card number. Facility Code The facility code is the code that is common to a group of cards or facility; this is also referred to as the site code or family number. Facility codes are not normally printed on a card. Multi Prox Proximity Reader and Pin Installer Manual 2 Card Number The card number identifies the card to the system; the card number is printed in the lower right of the card or across the back of the tag. Pin Number The pin number identifies a user in the system, this is entered by the user into the keypad on the Multi Prox. Index The Index is the location in memory where a user is stored. This is from 0 - 119, where index 0 would be User 1. Pre Alarm Time When the door contact is opened during the door unlock time a pre-
alarm warning will be sounded after the pre alarm time has expired to indicate the door left open alarm will be generated. Door Left Open Time When the door contact is left open during the door unlock time the beeper will be sounded continuously after the time has expired to indicate the door has been left open. Closing the door silences the Door Left Open Alarm. REX (Request to Exit) The REX or Request to Exit input is used to exit a door, the input can be connected to an exit detector, push button or other egress device to allow free exit of the door. 3 Multi Prox Proximity Reader and Pin Installer Manual MOUNTING When mounting the Multi Prox Proximity and Pin Reader please respect the following guidelines. Avoid wiring the Multi Prox cables in the same conduit with AC power cables, lock power, or signal wiring. Maintain all reader wiring a minimum of 12" (30cm) away from other wiring such as AC power, computer data wiring, telephone wiring and wiring to electric lock devices. Avoid installing within 3.5 feet (1.1m) of computer monitors or CRTs. The minimum distance will vary depending on the type of monitor or CRT. Avoid installing in proximity to sources of broad spectrum EMI noise such as motors, pumps, generators, DC to AC converters, uninterruptible power supplies, AC switching relays, light dimmers, computer monitors and CRTs. Avoid installing in proximity to potential sources of high power RF signal transmitters such as cellular telephones and two way radios. Multi Prox Proximity Reader and Pin Installer Manual 4 WIEGAND CONNECTION When using the standard Wiegand Interface to the access controller or reader expander two wiring methods can be used. Dual LED operation allows the signalling of both LED's independently using the LED control lines and is ideal to show the status of alarm or other integrated signals. Single LED allows a single LED line to control both LED colours. 5 Figure 1 - Dual LED Connection Multi Prox Proximity Reader and Pin Installer Manual Figure 2 - Single LED Connection Using the recommended cables listed in the technical specifications in section 7, splice these cables together with the pigtail of the reader and seal the splice. Route the cable from the reader to the host controller. Connect the cables as shown in Figure 1 for Dual LED Operation or Figure 2 for Single LED Operation. Do not connect the shield wires together at the reader cable splice. With the shield wire already terminated at the reader terminate the shield at the controller. For more information refer to Figure 1 and Figure 2. Multi Prox Proximity Reader and Pin Installer Manual 6 AUX BUTTON INPUT Button input wiring configuration is shown in Figure 3. For programming options refer to the Protg System Manual or the access controller manual for the system that the Multi Prox is connected to. Figure 3 - Button Input Wiring Connect a normally open button or switch as shown in Figure 3 and complete the programming within the Protg Integrated System for the functionality required. External Button Input Mode and single LED operation must be this wiring configuration. enabled when using 7 Multi Prox Proximity Reader and Pin Installer Manual PROGRAMMING By default the Multi Prox Proximity Reader is factory configured to send card data in 26 Bit Wiegand Format, send pin data in ARK-501 format, it will read all card formats and operate in the dual LED line mode. This configuration can be changed to suit system operating requirements. The programming mode can only be entered within the first 2 minutes from when the card reader powers up. ENTERING PROGRAMMING MODE To program the Card Reader badge hold the CLEAR key down for 3 seconds, the Card Reader will beep twice and illuminate the RED LED to indicate programming mode has been entered. Once in programming mode, if there is no activity on the Multi Prox for 30 seconds, programming mode is automatically exited with a long beep. If there is no activity on the keypad for 30 seconds the normal mode will be resumed. Multi Prox Proximity Reader and Pin Installer Manual 8 ADDRESS SELECTION To select an address to program enter the corresponding number into the keypad and press enter. If the address is valid the Card Reader will beep twice and the RED LED will start flashing. Address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Programming Option Card Reading Format Card Data Output Format LED Configuration Intelligent Tamper Mode Auxiliary Button Input Mode Pin Data Output Format Wiegand Site Code Standalone Operating Mode Standalone Entry Mode Add Standalone Super Card Add Standalone Super Pin Multi Prox RS485 Address Door Pre-Alarm Time Door Left Open Time Default Client Code Configuration For example to program address three (LED Configuration) press, 3 on the keypad and then ENTER. The card reader will then respond by beeping twice and flashing the RED LED to indicate data entry mode has been entered and that the user can enter the desired option. Entering an address value that does not exist or not entering any data when an address is selected will result in the reader timing out and a long Beep tone being generated. 9 Multi Prox Proximity Reader and Pin Installer Manual DATA PROGRAMMING To program a data value in the selected address location the same method as the address programming is used. Enter the value in using the keypad and press ENTER. The card reader will then respond by beeping twice indicating the data was programmed correctly and return to the address selection mode. An invalid entry will result in a long tone being generated. The data can be entered again or allow the Multi Prox to timeout to select another address. In the following sections the default configuration setting of each address is shown in bold text. ADDRESS 1 - CARD/TAG FORMAT The card/tag transponder format defines how the Multi Prox will decode cards and tags that are presented during standalone and normal operation. Setting 1 2 3 4 5 6 7 Function Read all card tag types. ICT Prox Format Postech Format HID Format ICT and HID Format ICT and Postech Format Postech and HID Format ADDRESS 2 - CARD DATA INTERFACE The card data interface format defines how the card data is sent using the DO and D1 data interface. Setting 1 2 Function 26 Bit Wiegand Format 34 Bit Wiegand Format Multi Prox Proximity Reader and Pin Installer Manual 10 3 4 Card Defined Wiegand Format 36 Bit (IEI) Wiegand Format ADDRESS 3 - LED CONTROL The LED Control Configuration settings allow the LED lines to operate in either multiple LED or single LED control. Setting 1 2 3 Function Dual LED Input; Red LED control line controls Red LED. Green LED control line controls Green LED. Red LED Always On; Red LED control line will turn Red LED off and Green LED on. Green LED Always On; Red LED control line will turn Green LED off and Red LED on. ADDRESS 4 - INTELLIGENT TAMPER Enabling the intelligent reader tamper mode will force the Multi Prox reader to check in to the device it is connected to every 30 seconds. Setting 1 2 Function Disabled Enabled Only enable Intelligent Reader Tamper Mode if the access control system or reader interface supports intelligent tamper operation. ADDRESS 5 - EXTERNAL BUTTON External button input allows the second LED input to be used as a multiple function input for Area Arming, Request to Exit and Request to Enter buttons. Enabling the external button input Multi Prox Proximity Reader and Pin Installer Manual 11 mode requires the Multi Prox to be configured in Single LED Mode Operation. Setting 1 2 Function Disabled Enabled Only enable the External Button Input Mode if the Multi Prox is connected using the single LED control lines. ADDRESS 6 - PIN DATA INTERFACE Max Pin 99999999 65535 99999999 99999999 99999999 99999999 1048575 Function ARK-501 26 Bit Wiegand Format 4 Bit 4 Bit with Parity 4 Bit Buffered 4 Bit Buffered with Parity 36 Bit Wiegand Format The pin data interface format defines how the pin data is sent using the DO and D1 data interface. Setting 1 2 3 4 5 6 7 ARK-501, 4 bit and 4 bit with parity send every button press instantly down the data interface. 26 bit Wiegand, 36 Bit Wiegand, 4 bit buffered and 4 bit buffered with parity buffers the key presses and sends them when the user presses ENTER. Pressing the CLEAR key wipes the buffer. If the max pin number is exceeded a long beep is generated and no data is sent. Max Pin Numbers are based on using an Integrated Control Technology Reader Module. When using the format 4 bit Buffered with Parity a Reader Expander set with the card format of 26 bit will decode pin codes that are 6 digits long as card numbers and Multi Prox Proximity Reader and Pin Installer Manual 12 handle it as a card. This is the same for HID 34 Bit with 8 digit pin codes. Where possible avoid these combinations. ADDRESS 7 WIEGAND SITE CODE When the either 26 bit or 36 bit Wiegand formats are selected they are sent with this site code. The default value is 0. The site code can be set from 0 - 255, select this address and enter the site code required. When using the Multi Prox with an ICT reader module leave the site code as 0 for the pin to be processed correctly as a pin code. ADDRESS 8 - OPERATION MODE The Multi Prox Proximity Reader provides a high level of flexibility and can be configured to operate in five different modes. Setting 1 2 3 4 5 Function Normal Pin and Prox Reader Input Mode. Standalone with 3 inputs and 2 outputs. RS232 Serial Communication Mode. Standalone operation with an RS-232 connection, 2 inputs and 1 output RS485 Serial Communication Mode. Standalone operation with an RS-485 connection, 2 inputs and 1 output Smart RS485 Communication Mode. Communicates with the ELT-KLCD and PRT-RDI2 directly 13 Multi Prox Proximity Reader and Pin Installer Manual ADDRESS 9 - STANDALONE ENTRY MODE Access can be granted when in Standalone mode using a card, pin number or combination of both. Setting 1 2 3 4 Function Card or Pin Card Only Pin Only Card and Pin ADDRESS 10 SUPER USER CARD This adds a Super User Card to the Multi Prox. A super user can open the door when a Multi Prox when operating in Standalone Mode. A super user can also change the state of the door; see Standalone Operation on page 18. To program a super user select address 10, the Multi Prox Proximity Reader will emit 2 beeps and then flash the RED LED, enter the index that you want to add the user into and press ENTER. The Multi Prox will respond with 2 beeps, and start flashing faster. Now present the card you want to add. The Multi Prox will emit 3 beeps to confirm the card can be added. Multiple super users can be programmed by selecting address 10 for each additional user. To delete a users card, enter the index for the user and press ENTER with out presenting a card. ADDRESS 11 SUPER USER PIN This adds a Super User pin to the Multi Prox. A super user can open the door when a Multi Prox when operating in Standalone Mode. A super user can also change the state of the door; see Standalone Operation on page 18. To program a super user select address 11, the Multi Prox Proximity Reader will emit two Multi Prox Proximity Reader and Pin Installer Manual 14 beeps and then flash the RED LED, enter the index that you want to add the user into and press ENTER. The Multi Prox will respond with 2 beeps, and start flashing faster. Now enter the pin number you want to add to the Multi Prox. The Multi Prox will emit 3 beeps to confirm the pin has been added. Multiple super users can be programmed by selecting address 10 for each additional user. To delete a users pin, enter the index for the user and press ENTER with out entering a pin number. ADDRESS 12 DEVICE ADDRESS The Multi Prox Proximity Reader can be assigned an address to allow more than 1 module to be connected in a RS485 network. The Multi Prox is set to address 0 by default, to change this enter the address between 0-127 you require. Setting 0 1
127 Function Address 0 Address 1
Address 127 ADDRESS 13 DOOR PRE ALARM When the Multi Prox Proximity Reader is operating in standalone mode the Orange Wire or Input Two (I2) on the PRX-SAM Interface Board is used to monitor the Door Contact. The Pre-
Alarm Time sets the period of time the door can be left open before a warning beep will be generated. The beeper will progress to a constant tone if the door exceeds the period of time set in the Door Left Open setting. The beeper will be silenced when the door is closed. Setting 1 Function Disabled 15 Multi Prox Proximity Reader and Pin Installer Manual 2 3 4 5 6 7 8 10 seconds 20 seconds 30 seconds 45 seconds 60 seconds 120 seconds 240 seconds ADDRESS 14 DOOR LEFT OPEN When the Multi Prox Proximity Reader is operating in standalone mode the Orange Wire or Input Two (I2) on the PRX-SAM Interface Board is used to monitor the Door Contact. The Door Left Open Time sets the period of time the door can be left open before a constant beep output will be generated. The beeper will be silenced when the door is closed. Setting 1 2 3 4 5 6 7 8 Function Disabled 10 seconds 20 seconds 30 seconds 45 seconds 60 seconds 120 seconds 240 seconds ADDRESS 15 DEFAULT Selecting address 15 will default the Multi Prox Proximity Reader to the factory defaults indicated in this manual and it will reset all standalone users. When you default the Multi Prox Proximity Reader will restart the unit and exit programming mode. This process takes 30 seconds. Multi Prox Proximity Reader and Pin Installer Manual 16 ADDRESS 16 SETUP CLIENT CODE The Multi Prox Proximity Reader can be configured to operate in a high security mode locking the reader and cards to a specific client code. Once this address has been selected you must present a valid ICT Client Programming card to set client code for the Multi Prox Proximity Reader. Setting this option will only allow cards with a valid client code for the card reader to be read. It is also recommended to set the Card/Tag Format (Address 1) to ICT Format to prevent other card formats from being read. 17 Multi Prox Proximity Reader and Pin Installer Manual STANDALONE OPERATION The Multi Prox can also operate in a Standalone mode when used with the PRX-SAM Interface Board. This enables single door control for a 125 user system. PROGRAMMING USERS Users must be programmed through the Nano Prox Access Manager Application that can be freely downloaded from our website, www.integratedcontroltechnology.com. Using this software users can be added very quickly through the WindowsTM interface; by either presenting a card to the Multi Prox, typing the details in by hand or importing the details from a spreadsheet. Site information can also be saved and downloaded to multiple Multi Proxs for larger sites. Set up of the Multi Prox pre-alarm time, left open time and super user settings can also be configured from this software. SUPER USER MODE Super users have the ability to toggle the lock output by holding down the ZERO KEY for 2 seconds before presenting their card, or entering their pin number. When the door is unlocked in a super user mode the Multi Prox will respond with 4 beeps. There are 5 super user modes available, that can be changed using the NanoProx PC software. Unlock Latched (default option) Unlock for 2 hours Unlock for 4 hours Unlock for 8 hours Super User Mode disabled Multi Prox Proximity Reader and Pin Installer Manual 18 SPECIFICATION Power Supply Voltage Current Card Tag Read Range Standalone Operation Interface Wiegand Distance Users Access Level 12VDC (9.5 - 14.0VDC) 120mA (Peak, Reading) Up to 12cm (4") Up to 8cm (2.5") 120 (Unlimited Super/Master User) 3 (Master, Super, User) Multiple Format 26, 34, 37 Bit Data 0 and Data 1 150 Meters (500 feet) Field 125KHz Pulse Width Modulated Multi Conductor Frequency Cable Type Temperature
*Specifications visit www.integratedcontroltechnology.com for the updated information. Read range is specified using an ICT card format and the card is presented parallel to the reader using installation procedures detailed in this manual without any electrical interference present. 22Awg Alpha 5196, 5198 18Awg Alpha 5386, 5388 18Awg Beldon 9553
-35- +65 Celsius
-31 - 149 Fahrenheit Operating change without subject notice, please are to 19 Multi Prox Proximity Reader and Pin Installer Manual WARRANTY The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. The Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system. Seller's obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not meeting the specifications. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits, stolen goods, or claims by any other party caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold. Protg and the logo are registered trademarks of Integrated Control Technology Limited. Multi Prox Proximity Reader and Pin Installer Manual 20 NOTES _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ NOTES _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ Multi Prox Proximity Reader and Pin Installer Manual 22 Multi Prox Proximity Reader and Pin Installer Manual 24 Unit C, 6 Ascension Place, Mairangi Bay, P.O. Box 302-340 North Harbour, Auckland, New Zealand. Phone: +64 (9) 476 7124 Fax: +64 (9) 476 7128