FCC ID: UAUWIRELESSCML Wireless Lock Product.

Wireless Lock Range Cartridge Mortise Wireless Lock Installation Manual The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited, Protege and the Protege Logo are registered trademarks of Integrated Control Technology Limited. All other brand or product names are trademarks or registered trademarks of their respective holders. Copyright Integrated Control Technology Limited 2003-2023. All rights reserved. Last Published: 24-Jul-23 03:15 PM Cartridge Mortise Wireless Lock | Installation Manual 2 Contents Introduction About This Product How Does It Work?

Hardware Options Replacement Parts MIFARE Technology About MIFARE Secured MIFARE Card Format About MIFARE DESFire EV1 About MIFARE DESFire EV2 About MIFARE DESFire EV3 MIFARE/DESFire Products Installation Requirements Installation Installation Overview What's Included?

Installing the Strike Plate Installing the Lock Position the Lock Cable Secure the Lock Fit the Handle and Sectional Trim Key Cylinder and Privacy Thumbturn Installing the Faceplate Installing the Lock Control Cartridge Position the Reader Cable Connect the Lock Cable Secure the Cartridge Installing the Reader Connect the Reader Attach the Reader Inserting the Batteries Installing the DPS Magnet Bluetooth Node Connection RS-485 Node Connection Cartridge Mortise Wireless Lock | Installation Manual 5 5 5 7 9 10 10 10 10 10 11 11 12 13 13 14 14 15 15 16 17 19 20 21 21 22 23 24 24 25 26 27 28 28 3 Shield Connection Programming the Reader Protege Config App Operation Maintenance Mechanical Layout Door Template Technical Specifications New Zealand and Australia European Standards UK Conformity Assessment Mark UL and ULC Installation Requirements CAN/ULC-60839-11-1 UL 294 UL 10C FCC Compliance Statements Industry Canada Statement Disclaimer and Warranty 29 30 30 31 33 34 35 37 39 40 41 42 42 42 42 43 44 45 Cartridge Mortise Wireless Lock | Installation Manual 4 Introduction This installation manual provides instructions and technical specifications for installation of the ICT Cartridge Mortise Wireless Lock. About This Product The ICT Cartridge Mortise Wireless Lock combines an advanced-technology, intelligent wireless credential reader with leading mortise locking system technology. With no cabling necessary this provides sites with the ability to deploy integrated electronic access control in areas where traditional wired locking solutions may not be possible. Current features of the lock control card reader include:

Integrated LED indicator provides read response and status signaling Bluetooth Wireless Technology MIFARE and DESFire credential reading Keep alive transmission every 30 seconds for intelligent tamper management USB-C connection to supply power for emergency opening Supports online or offline operation Reader configuration programmable via the Protege Config App Advanced technology wireless operation provides 2 years battery life (40,000 activations ) How Does It Work?

Online Mode When the wireless lock is configured to operate in online mode it operates almost the same as a wired system. A wired Bluetooth node acts as a network connection point, facilitating communication between the lock and the controller. When a user presents their credential the lock checks their access permissions in real time, via the Bluetooth node. Access is granted or denied accordingly and events are communicated back to the controller. Locks are configured for one mode or the other. When a lock that is configured to operate in online mode loses connection to the Bluetooth node or hub it does not revert to operating in offline mode ('data on card'). It will flash a red LED every second to indicate lost connection. It will not unlock for any credential presented. When a user presents their credential at a wireless lock operating in online mode the lock sends a request via the Bluetooth node to check the access permissions of the supplied credential. The controller processes the request and provides an access decision response. The lock grants or denies access accordingly, then sends the related events to the controller. When the user presents their credential at the next lock the process is repeated. Cartridge Mortise Wireless Lock | Installation Manual 5 Request Events Decision Request Events Decision Wireless LockWirelessLock Offline Mode Unlike online operation, where the lock checks with the controller to determine whether to grant or deny access, in offline wireless lock operation a user's access permissions are carried in their credential ('data on card'). When the wireless lock is configured to operate in offline mode each user acts as a walking data store, carrying their credential and event data to and from the locks, like a colony of ants creating a mobile data network. When a user presents their credential at a wired update point (such as at a main entrance) the reader downloads a

'credential blob' to the card/phone. This credential blob contains encrypted information about the access rights for that specific credential, including which doors they can access and when. It also includes a blocklist of users who have recently been banned from the site. When the user presents their credential at a wireless lock the credential blob tells the lock whether that user should be granted or denied access. All the lock has to do is follow the instructions. The blocklist is also uploaded to the lock to ensure that inactive users who have not yet had their credential blob updated can no longer gain access. At the same time the lock downloads the user's events to their credential, and when they next present at a wired update point their accumulated events are uploaded to the controller. Access-related programming changes to doors, access level, schedules and so on are downloaded to the controller as normal. The next time the user presents the credential at a wired update point the credential blob is updated with any changes that affect their access for that specific credential. A site may have both locks configured to operate in online mode and locks configured to operate in offline mode . Cartridge Mortise Wireless Lock | Installation Manual 6 Wireless LockWireless LockWireless LockUpdate PointUpdate Point Events CredentialBlob Update Events Credential Blob Events CredentialBlob Update Events Credential Blob Events Credential Blob Hardware Options The ICT Cartridge Mortise Wireless Lock offers the flexibility to create your own configuration. Simply choose your preferred components from the range of available options to compile your perfect combination. 1. Specify the Electronic Cartridge configuration. 2. Choose a Reader Cover. 3. Select the Mortise Lock Body type. 4. Specify the Handing. 5. Select the optional Key Cylinder if required. 6. Select a Handle Set. 7. Select the Sectional Trim. 8. Specify the Finish. Cartridge Mortise Wireless Lock Options Electronic Cartridge Mortise Electronic Cartridge &Reader Mortise Electronic Cartridge &Reader with Door Position Sensor Reader Cover Black Circular Black Rectangular White Circular White Rectangular Mortise Lock Body Mortise Lock Body Mortise Lock Body with Deadbolt and Thumbturn Handing Left Hand Right Hand Left Hand Return Right Hand Return Optional Key Cylinder Key Cylinder Two keys are supplied with each lock. Code CME-DFBT CME-DFBT-DPS Code MC-BC MC-BR MC-WC MC-WR Code MLB MLB-DB Code LH RH LHR RHR Code MK Cartridge Mortise Wireless Lock | Installation Manual 7 Handle Set Acadia Aspiring*

Banff Denali Glacier Jasper Nightcap Peak Sequoia Code MH-AC MH-AS MH-BA MH-DE MH-GL MH-JP MH-NI MH-PE MH-SE

* Handing needs to be specified when ordering the Aspiring handle set. Other handles are non-handed. Sectional Trim Round Rose Square Rose Finish Bright Brass Clear Coated Satin Brass Clear Coated Satin Bronze Clear Coated Oil Rubbed Bronze Flat Black Satin Chromium Plated Bright Stainless Steel Satin Stainless Steel Code MR-RO MR-SQ Code 605-BB 606-SB 612-SB 613-RB 622-FB 626-SC 629-BS 630-SS Color selection applies to faceplate, strike plate, handle, trim, key cylinder, thumbturn and cartridge armor plate. Cartridge Mortise Wireless Lock | Installation Manual 8 Replacement Parts In addition to the components included in the initial installation, the following individual components may be ordered for replacement. The required finish will need to be specified when ordering replacement parts. Thumbturn Replacement Mortise Thumbturn Mortise Lock Strike Plate Replacement Mortise Strike Plate Mortise Lock Faceplate Replacement Mortise Dress Plate (no Deadbolt) Mortise Dress Plate (with Deadbolt) Electronic Lock Control Cartridge Armor Plate Replacement Cartridge Dress Plate Code MT Code SPM Code DPM DPM-DB Code DPC Cartridge Mortise Wireless Lock | Installation Manual 9 MIFARE Technology About MIFARE Based on the international standard ISO/IEC 14443 Type A, MIFARE is a technology used for contactless RFID smart card systems consisting of card and reader components. Fully compliant with the international standard ISO/IEC 14443 Type A Multi-application memory to store several services on the same card, allowing for many integration possibilities Fast transaction speed High security and fraud protection Secured MIFARE Card Format Secured MIFARE is the compromise between secured cards and cost. Card data is protected with a diversified authentication key and encrypted with an AES256 algorithm. These cards are not as secure as MIFAREDESFire but still provide high security against cloning. This card mode can be used on all MIFARE 1K (S50) cards and tags. About MIFARE DESFire EV1 MIFARE DESFire EV1 is an ideal solution for multi-application smart cards in transport schemes, e-government or identity applications. It complies fully with the requirements for fast and highly secure data transmission, flexible memory organization, and interoperability with existing infrastructure. Fully compliant with the international standard ISO/IEC 14443 Type A 1-4 Common Criteria EAL4+ security certified Secure, high speed command set Unique 7-byte serial number Open DES/3DES crypto algorithm in hardware Open AES 128 bit crypto algorithm in hardware About MIFARE DESFire EV2 MIFARE DESFire EV2 delivers the perfect balance of speed, performance and cost-efficiency. For a truly convenient touch-and-go experience, MIFARE DESFire EV2 offers increased operating distance. Based on global open standards for both air interface and cryptographic methods, it complies with all requirements for fast and highly secure data transmission and flexible application management. Fully compliant with all levels of the international standard ISO/IEC 14443A Common Criteria EAL5+ security certified Secure, high speed command set Unique 7-byte serial number Open DES/3DES crypto algorithm in hardware Open AES 128 bit crypto algorithm in hardware Fully interoperable with existing NFC reader infrastructure Backwards compatible with all previous MIFARE DESFire generations Cartridge Mortise Wireless Lock | Installation Manual 10 About MIFARE DESFire EV3 The latest addition to the MIFARE DESFire product family, MIFARE DESFire EV3 offers even more advanced hardware and software implementation on a brand new internal chip, and combines enhanced performance with a greater operating distance and improved transaction speed compared to its predecessors. Based on global open standards for both air interface and cryptographic methods, it uses the same security certification level as IC products used for banking cards and electronic passports. Featuring an on-chip backup management system and mutual three-pass authentication, EV3 supports confidential and integrity-protected communication with secure dynamic messaging and mirroring. Fully compliant with the international standard ISO/IEC 14443 Type A 1-4 and ISO/IEC 7816-4 Common Criteria EAL5+ security certified for IChardware and software NFC Forum Tag Type 4 certified Secure, high speed command set Unique 7-byte serial number Choice of open DES/2K3DES/3K3DES/AES crypto algorithms Open AES 128 bit crypto algorithm in hardware Fully interoperable with existing NFC reader infrastructure Transaction timer mitigates risk of man-in-the-middle attacks Backwards compatible with all previous MIFARE DESFire generations MIFARE/DESFire Products The MIFARE/DESFire products can be expanded to accommodate large numbers of modules using the encrypted RS-485 Network. ICT provides a number of reader and physical credential options in the MIFARE/DESFire range. Physical Credentials Proximity clamshell card Proximity ISOcard Proximity ISOdual technology card Proximity standard key tag Proximity adhesive disc Proximity silicone wristband Physical credentials are available in an extensive range of technology and EEPROM size configurations. Visit the ICT website to view the full range of proximity products. For more information on configuration options and ordering, contact ICT Customer Services. Cartridge Mortise Wireless Lock | Installation Manual 11 Installation Requirements This equipment is to be installed in accordance with:

The product installation instructions UL 294 - Access Control System Units UL 681 - Installation and Classification of Burglar and Holdup Systems UL 827 - Central-Station Alarm Services UL 1034 - Burglary-Resistant Electric Locking Mechanisms CAN/ULC-S301, Central and Monitoring Station Burglar Alarm Systems CAN/ULC-S302, Installation and Classification of Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults CAN/ULC-S561, Installation and Services for Fire Signal Receiving Centres and Systems CAN/ULC-60839-11-1, Alarm and Electronic Security Systems Part 11-1: Electronic Access Control Systems System and Components Requirements The National Electrical Code, ANSI/NFPA 70 The Canadian Electrical Code, Part I, CSA C22.1 The Local Authority Having Jurisdiction (AHJ) Cartridge Mortise Wireless Lock | Installation Manual 12 Installation Installation of the wireless lock requires the following steps to be completed in the correct sequence. 1. Install the strike plate (see next page). 2. Install the lock.

Position the lock cable (see page15). Secure the lock (see page16). 3. Fit the handle and sectional trim (see page17). 4. 5. 6. If included, fit the optional key cylinder and privacy thumbturn (see page19). Install the faceplate (see page20). Install the lock control cartridge.

Position the reader cable (see page21). Connect the lock cable (see page22). Secure the cartridge (see page23). 7. Install the reader.

- Attach the reader base (see page25).

Connect the reader (see page24). 8. Insert the batteries (see page26). Installation Overview The following image provides a general overview of the lock installation, the components and their positioning. The above diagram is for illustration purposes only. Installation options such as deadbolt, key cylinder, thumbturn, handle style and reader cover options are dependent on the hardware variations installed. Cartridge Mortise Wireless Lock | Installation Manual 13 Reader CoverReaderFerrite ShieldKey Cylinder (Optional)Outside RoseOutside LeverOutside SpindleKey Cylinder CollarKey Cylinder SpringOutsideInsideInside SpindlePrivacy Thumbturn(Optional)Inside RoseInside LeverRose ScalpBatteriesLock Control CartridgeCartridge Armor PlateMortise Lock Cartridge What's Included?

The ICT Cartridge Mortise Wireless Lock is supplied with the following components. 1 x 13.56MHz lock control credential reader with Bluetooth Wireless Technology

- USB-C connection to supply power for emergency opening

1 x Reader cover (rectangular or circular) 1 x Reader mounting base 1 x Ferrite shield 2 x N4 9.5mm pan head self-tapping screws for mounting the reader base 1 x Electronic lock control cartridge

8-wire reader cable wiring loom with socket plug for connection to the reader 1 x Armor plate 2 x Countersunk G8 x 3/4" flat head screws for securing the cartridge body 2 x Countersunk M3.5 x 6mm Pozidriv screws for installing the armor plate 3 x Alkaline LR06 AA 1.5V batteries 1 x Grade 1 mortise lock

8-wire lock cable wiring loom with socket plug for connection to the lock control cartridge 1 x Faceplate 2 x Countersunk #12-24 combo screws for securing the lock body 2 x Countersunk #8-32 x 1/4" flat head machine screws for installing the faceplate 1 x Dead latch plate and strike plate 2 x #12-24 combo screws for installing the strike plate 1 x Door handle kit with sectional trim Optional key cylinder Installing the Strike Plate 1. Prepare the door jamb for the mortise lock strike plate. 2. Install the dead latch plate behind the strike plate, with the slider toward the bottom for dead latch. 3. Using the two #12-24 combo screws provided, secure the dead latch plate and strike plate in position. Cartridge Mortise Wireless Lock | Installation Manual 14 Installing the Lock Position the Lock Cable Before the mortise lock can be installed the lock cable needs to be threaded through from the lock cavity to the cartridge cavity. This cannot be done after the lock is installed. 1. Feed the lock cable in through the lock cavity and up through the cable hole into the cartridge cavity. It may be helpful to attach a semirigid wire to the lock cable connector plug and pull the lock cable up through the cable hole (see below). Pass the wire through the cable hole. Attach the wire to the lock cable. Cartridge Mortise Wireless Lock | Installation Manual 15 Semirigid Wire Secure the Lock 1. Insert the mortise lock cartridge into the lock cavity, ensuring the cable remains in position. 2. Using the two #12-24 combo screws provided, secure the lock body in position. Cartridge Mortise Wireless Lock | Installation Manual 16 Fit the Handle and Sectional Trim Assemble the handle and sectional trim, ensuring the correct inside/outside door and handle positions and spindle orientation. 1. Assemble the outside rose. i. Fit the rose scalp cover onto the outside rose assembly by aligning the dimples with the slots in the rose plate. Secure by rotating clockwise until tight. ii. Fit the handle onto the rose assembly spindle. iii. Using the M5 x 0.8 x 14mm socket head cap screw and 4mm hex key provided, secure the handle. 2. Assemble the inside rose. This step is not required for Aspiring and Jasper handle sets (see Step 6). i. Fit the handle onto the rose assembly spindle. ii. Using the M5 x 0.8 x 14mm socket head cap screw and 4mm hex key provided, secure the handle. The inside rose scalp cover should not be installed at this point. Cartridge Mortise Wireless Lock | Installation Manual 17 3. 4. Install the spindles and springs on both sides, ensuring the correct spindle orientation (see above). Install the outside assembly, aligning with the spindle. Confirm spindle engagement by rotating the lever down and verifying that the latch retracts. 5. Install the inside assembly, aligning with the spindle. Confirm spindle engagement. i. Using the #10-24 x 1-1/2" flat head machine screws provided, secure the inside rose assembly. ii. Fit the rose scalp cover onto the inside rose assembly by aligning the dimples with the slots in the rose plate. Secure by rotating clockwise until tight. 6. For Aspiring and Jasper handle sets only:

i. Slide the lever onto the assembly spindle, ensuring the screw hole is on the underside of the lever. ii. Using the M5 x 0.8 set screw and 2.5mm hex key provided, secure the lever. Cartridge Mortise Wireless Lock | Installation Manual 18 Spindle Orientation Key Cylinder and Privacy Thumbturn The following instructions are only required if installing the optional key cylinder and privacy thumbturn. Ensure that the key cylinder is installed on the outside of the door with the thumbturn on the inside. 1. Thread the key cylinder into the lock body until the cylinder is flush or slightly recessed in the trim collar. 2. Using the 2.5mm hex key provided, through the front of the lock cartridge tighten the set screw on the side of the key cylinder to secure it in position. 3. Install the thumbturn. Secure using the two stainless steel #6 x 1/2" truss head sheet metal screws provided. Cartridge Mortise Wireless Lock | Installation Manual 19 Installing the Faceplate 1. Using the two #8-32 x 1/4" flat head machine screws provided, install the faceplate. Cartridge Mortise Wireless Lock | Installation Manual 20 Installing the Lock Control Cartridge Position the Reader Cable Before the electronic control cartridge can be installed the attached reader cable needs to be secured from inside the cartridge cavity out through the reader hole using a semirigid wire. While it may be possible to locate and pull the reader cable through the reader hole after installing the cartridge this will not be possible for some door configurations. Due to the short length of the reader cable and variable door conditions it is recommended to position the reader cable before inserting the cartridge. 1. Attach a semirigid wire to the reader cable connector. 2. Feed the wire in through the cartridge cavity and out through the reader hole so that the reader cable can be pulled through after installing the cartridge. Cartridge Mortise Wireless Lock | Installation Manual 21 Semirigid WireReader Cable Connect the Lock Cable Before installing the cartridge the lock cable needs to be connected. 1. Connect the black lock cable socket plug to the black connector on the bottom of the cartridge. 2. Secure the lock cable to the spare cable clip on the underside of the cartridge. Cartridge Mortise Wireless Lock | Installation Manual 22 Lock CableReader CableCable Clips Secure the Cartridge 1. Insert the lock control cartridge into the cartridge cavity. 2. Pull the reader cable through the reader hole. 3. Using the two G8 x 3/4" flat head screws provided, secure the cartridge in position. Cartridge Mortise Wireless Lock | Installation Manual 23 Installing the Reader Connect the Reader 1. Using a small flat screwdriver, release the tab at the bottom of the reader to separate the reader cover from the base. 2. If mounting the reader on a metal surface it is recommended to place the optional ferrite shield (provided) onto the back side of the reader base. The shield is placed between the reader and the mounting surface to suppress electromagnetic interference caused by the reader's proximity to the metal surface. 3. Connect the reader cable plug to the connector on the back of the reader board. 4. Thread the other end of the reader cable through the hole in the door and out to the other side. Cartridge Mortise Wireless Lock | Installation Manual 24 Ferrite Shield Attach the Reader 1. Position the reader onto the door, ensuring the USB port is at the bottom. 2. Using the two self-tapping N4 9.5mm pan head screws provided, fasten the reader in position on the door. Do not use screws longer than 9.5mm to mount the reader. 3. Position the reader cover over the reader, with the LED strip at the top, and press firmly until the cover clips into position. Attach the reader with the USBport at the bottom. Attach the cover with the LEDstrip at the top. Either a rectangular or circular reader cover may be ordered. The process is the same for both covers. It is not possible to detach the reader board from the base while it is firmly mounted in position. You will need to loosen or remove the mounting screws to allow the flex required to clip/unclip the board (e.g. for maintenance). Cartridge Mortise Wireless Lock | Installation Manual 25 USB PortLED Strip Inserting the Batteries Rechargeable batteries are not recommended due to reduced charge time and lock operation. 1. Remove the battery holder from the cartridge. 2. Lift the battery cover and insert the 3 x AA batteries provided. 3. Push the battery holder back into the cartridge. 4. Using the two M3.5 x 6mm Pozidriv machine screws provided, install the armor plate. For UL installations (UL 294), ULapproved batteries must be used. For ULC installations (CAN/ULC 60839-11-1), ULCapproved batteries must be used. Approved batteries include Energizer Ultimate Lithium and Energizer MAX Alkaline. Cartridge Mortise Wireless Lock | Installation Manual 26 PULULC Installing the DPS Magnet This step applies to the Mortise Electronic Cartridge &Reader with Door Position Sensor (CME-DFBT-DPS) only. For electronic cartridge models which have a DPS(Door Position Sensor) included, the accompanying magnet needs to be installed in the door jamb as directly opposite the sensor as practical. There is no need to install or connect the sensor itself as it is preinstalled in the electronic lock control cartridge. The sensor is positioned 100mm from the top of the cartridge armor plate. Note that it is slightly off-center to the reader side, although this difference is negligible in door position operation. The sensor has an operating range of approximately 12mm from the armor plate to the magnet before contact is broken. Cartridge Mortise Wireless Lock | Installation Manual 27 100mm (3 15/16")14.9mm(19/32")16.9mm(21/32") Bluetooth Node Connection Online operation is achieved using a Bluetooth communication node, wired to the controller's RS-485 port to act as a network connection point between the wireless lock and the controller. One Bluetooth node supports up to 20 wireless locks operating in online mode. Using the recommended cables, splice the cable together with the pigtail of the Bluetooth node and seal the splice. Route the cable from the node to the host module. Connect the cable to the module port as shown in the connection diagram that follows. The recommended cable types for RS-485 are:

Belden 9842 or equivalent 24 AWG twisted pair with characteristic impedance of 120ohm Maximum distance: 900m (3000ft) For UL installations, a UL Listed (UL 294) node and controller must be used. For ULC installations, a ULC Listed (CAN/ULC 60839-11-1) node and controller must be used. RS-485 Node Connection The connection of a Bluetooth communication node to a controller. Wiring Connections Color Wire Connection Red Black V+ 12VDC positive V- 12VDC negative Yellow D0/NA RS-485 A Violet Shield D1/NB RS-485 B Shield (drain) wire. Frame grounded at one point only Cartridge Mortise Wireless Lock | Installation Manual 28 PULULCD0/NAD1/NBL1BZZ4V-Z3Z2V-Z1V+V-Shield Connection Connect the Bluetooth node pigtail shield and cable shield wires together at the node pigtail splice. Connect the cable shield to a suitable earth point. Do not connect the cable shield to a ground or AUX connection. The node pigtail shield wire is not terminated inside the reader. Important:

The node must be connected to the module port using a shielded cable. The shield must only be connected at one end of the cable in the metallic enclosure (frame grounded). Do not connect the cable shield to an AUX-, 0V or V- connection on the module. Do not connect the cable shield to any shield used for isolated communication. The node pigtail shield and cable shield wires should be joined at the node pigtail splice. Do not terminate the node shield wire inside the node. Cartridge Mortise Wireless Lock | Installation Manual 29 Programming the Reader ICT credential readers can be programmed for a wide range of functionality to suit your site's requirements. Programming options are dependent on hardware compatibility and firmware versions. Readers can be programmed using a mobile device running the Protege Config App. Reader configuration is programmed by applying specific TLV (Type Length Value) settings to the reader to enable, disable and configure reader options. Important: Readers can only be programmed within 2 minutes of startup. You will need to remove the batteries to disconnect the power supply, then apply the programming within 2 minutes of powering up. Protege Config App The Protege Config App provides a secure, convenient and flexible method for programming ICT credential readers. To use the Config App you will need:

An app account A mobile credential Programming Summary To program a reader using the Config App:

1. Log in to the app using your app account. 2. Select your Credential Profile. Your credential profile is automatically assigned to your app account with your mobile credential, and is based on the credential issuer and the site the credential was allocated to. 3. Create a Reader Configuration (config) comprising the required TLVsettings. 4. Activate Bluetooth on your device (if not already activated). 5. Power cycle the reader you want to program. 6. Select the config to program the reader with. 7. Apply the configuration to the reader, within two minutes of startup. Hold your mobile device close to the reader and tap Scan Closest to apply the configuration. When programming is successful the reader will beep 4 times quickly, then restart. For information on using the Config App, see the Protege Config App User Guide, available from the ICT website. Cartridge Mortise Wireless Lock | Installation Manual 30 Operation ICT wireless locks provide specific audio and visual signals to indicate read response and current status. The following table describes the available LEDand beeper response signals. Beeper Indicators Short beeps have a sound and interval duration of 100ms. Long beeps have a sound and interval duration of 1 second. Low Battery Indicators Yellow flash indicates battery voltage less than 3.8V. Batteries need to be replaced within 2-3 months. Red flash indicates battery voltage less than 3.55V. Batteries need to be replaced within 2-3 weeks. Operation Access Granted Access Granted - Battery Low < 3.8V Access Granted - Battery Low < 3.55V Access Denied Access Denied - In Privacy Mode Access Denied - Battery Low < 3.8V Access Denied - Battery Low < 3.55V Construction Mode - Access Granted Construction Mode - Access Granted - Battery Low < 3.8V LED Indication LED Description Beeper 3 Green flashes

(100ms/100ms) 2 Green flashes

(100ms/100ms) 1 Yellow flash

(200ms) 2 Green flashes

(100ms/100ms) 1 Red flash

(200ms) 3 Red flashes

(100ms/100ms) 3 Red flashes

(200ms/200ms) 2 Red flashes

(100ms/100ms) 1 Yellow flash

(200ms) 2 Red flashes

(100ms/100ms) 1 Red flash

(200ms) 3 Purple flashes

(100ms/100ms) 2 Purple flashes

(100ms/100ms) 1 Yellow flash

(200ms) 2 short 2 short 2 short 1 long 1 long 1 long 1 long 2 short 2 short Cartridge Mortise Wireless Lock | Installation Manual 31 Operation LED Indication LED Description Beeper Construction Mode - Access Granted - Battery Low < 3.55V Construction Mode - Access Denied Construction Mode - Access Denied - Battery Low < 3.8V Construction Mode - Access Denied - Battery Low < 3.55V Exit Leaves Open Mode - Lock/Unlock Granted Exit Leaves Open Mode - Lock/Unlock Denied Opening Not Allowed - Battery Flat Powering Up 2 short 1 long 1 long 1 long 1 short 1 long 1 short 2 short 2 Purple flashes

(100ms/100ms) 1 Red flash

(200ms) 3 Orange flashes

(100ms/100ms) 2 Orange flashes

(100ms/100ms) 1 Yellow flash

(200ms) 2 Orange flashes

(100ms/100ms) 1 Red flash

(200ms) 1 Green flash

(100ms) 3 Red flashes

(100ms/100ms) 1 Red flash

(20ms) Flashing Blue

(200ms/200ms) until ready to read

(typically 1.5s) Flashing Blue

(200ms/200ms) Powering Up - Battery Low < 3.8V until ready to read 2 short 1 Yellow flash

(200ms) Flashing Blue

(200ms/200ms) Powering Up - Battery Low < 3.55V until ready to read 2 short Factory Reset Blob Version Not Supported Blob Contains No Configuration 1 Red flash

(200ms) 5 White flashes

(100ms/100ms) 1 White flash

(100ms) 1 White flash

(500ms) Cartridge Mortise Wireless Lock | Installation Manual 32 Maintenance ICT cartridge mortise wireless locks have an expected battery life of approximately 2 years (40,000 activations), dependent on usage levels and reader configuration. Maximum 140,000 activation cycles with MIFARE/DESFire or NFC credentials Maximum 180,000 activation cycles with Bluetooth Wireless Technology credentials Batteries should be replaced every two years, or earlier if required. In case of battery failure, emergency power can be supplied via the USB-C port at the base of the reader. Cartridge Mortise Wireless Lock | Installation Manual 33 Mechanical Layout Cartridge Mortise Wireless Lock | Installation Manual 34 31.75mm(1.25)149.5mm(5.88)12.5mm(0.49)40mm(1.57)48mm(1.88)178mm(7)31.75mm(1.25)149.5mm(5.88)12.5mm(0.49)178mm(7)45mm(1.77) Door Template May not be to scale. Cartridge Mortise Wireless Lock | Installation Manual 35 31.7mm (1 1/4")46mm (1 13/16")19mm(3/4")9.5mm (3/8")85.7mm (3 3/8")104.8mm (4 1/8")15.9mm (5/8")2.4mm (3/32")25.4mm (1")MinimumSTRIKECLLOCKCL2x #12-24COMBOSCREW(WMS)CLDOOR19mm(3/4")19mm(3/4")22.2mm (7/8")9.5mm (3/8")9.5mm (3/8")92.1mm (3 5/8")61.9mm (2 7/16")35mm (1 3/8")27mm (1 1/16")(2x)3.2mm (1/8")INSIDE ONLY15.9mm (5/8")INSIDE ONLY36.5mm (1 7/16")30.9mm (1 7/32")178mm (7")69.8mm (2 3/4")BACKSET AT DOOR EDGEBEVEL CENTERLINE(2x)2mm (5/64")22.2mm (7/8")HandleOutside Only,Reader HoleInside Only,OptionalThumbturnOutside Only,OptionalKey CylinderHoleLEVERCLOutside SectionRight Hand doortemplate123.8mm (4 7/8") Cartridge Mortise Wireless Lock | Installation Manual 36 25.4mm (1")142.9mm (5 5/8")184.1mm (7 1/4")203.2mm (8")44.5mm (1 3/4")Standard Door ThicknessConsult provider for other Door Sizes71.4mm (2 13/16")92.1mm (3 5/8")101.6mm (4")42.9mm (1 11/16")65mm (2 9/16")150mm (5 29/32")20.6mm(13/16")100mm (3 15/16")31.7mm (1 1/4")(2x)3.2mm (1/8")9.5mm(3/8")Vertical centerline of DoorStrike LipPosition2x #12-24COMBOSCREW(WMS)69.8mm (2 3/4")114.3mm (4 1/2")MINIMUM5.5mm(7/32")168.3mm (6 5/8")110mm (4 3/8")4mm (5/32")120.6mm (4 3/4")60deg16mm (5/8")35mm(1 3/8")HandleLEVERCLLOCKCLSTRIKECL65mm (2 9/16")31.7mm (1 1/4") Technical Specifications The following specifications are important and vital to the correct operation of this product. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void. Ordering Information Order Codes Power Supply Battery See Hardware Options Alkaline LR06 - AA 1.5V (x3) 2 years 40,000 activation cycles Expected Battery Life Maximum 140,000 activation cycles with MIFARE/DESFire Maximum 180,000 activation cycles with Bluetooth mobile Emergency Power Supply USB-C connection allows power supply for emergency opening Operating Voltage 3.3 6V Operating Current 370mA (Peak, Door Activation) Average Operating Current 82A (Standby Mode) Memory Event Memory Storage 40,000 log entries Communications Frequency Card Read Range Tag Read Range 13.56 MHz ISO/IEC 14443 Type A 20mm (0.79") (Typical) 15mm (0.59") (Typical) Bluetooth Wireless Technology Bluetooth Read Range Proximity mode: up to 0.5m (1.6ft) configurable Action unlock (shake): up to 5m (16.4ft) configurable Bluetooth Electronic Credential Transmission Technology Bluetooth version 5.2 compliant Proprietary data exchange protocol. AES-128 encrypted Credentials can be distinguished by unique site code and card number Bluetooth Wireless Device Protege Mobile 1.0.x Dimensions Reader Cover Circular (OD x D) 45 x 12.5mm ( 1.77 x 0.49") Rectangular (H x W x D) 48 x 40 x 12.5mm (1.89 x 1.57 x 0.74") Control Cartridge (H x W x D) 95 x 42.8 x 18.9mm (3.74 x 1.69 x 0.49") Armor Plate (H x W) 150 x 31.7mm (5.9 x 1.25) Net Weight Gross Weight Operating Conditions 310g (10.9oz) TBC Operating Temperature UL/ULC 0 to 55C (32 to 131F) Cartridge Mortise Wireless Lock | Installation Manual 37 Storage Temperature

-10 to 85C (14 to 185F) Humidity 0%-93% non-condensing, indoor use only (relative humidity) Mean Time Between Failures

(MTBF) Lock Specification 520,834 hours (calculated using RDF 2000 (UTE C 80-810) Standard) Lock Type Net Weight Casing Faceplate Strike Plate Latchbolt Deadbolt Default Keyway Default Keying Handle Rotation Door Thickness Grade 1 mortise lock TBC 12 gauge heavy duty dichromated alloy steel Stainless steel. Beveled. H x W 203.2 x 31.75mm (8 x 1.25) Stainless steel. Non-handed. Curved lip Stainless steel. Anti-friction. 19mm (0.75) throw Stainless steel. 25.4mm (1") throw Schlage C Compatible (SCC). Other options available on request Keyed Different (KD). Other options available on request 35 degrees 44.45 to 50.8mm (1.75 to 2) standard. Larger thickness by special order The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Integrated Control Technology is under license. Other trademarks and trade names are those of their respective owners. Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest documentation and product information. Cartridge Mortise Wireless Lock | Installation Manual 38 New Zealand and Australia Intentional Transmitter Product Statement The R-NZ compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. Cartridge Mortise Wireless Lock | Installation Manual 39 European Standards CE Statement Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast

(RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863. This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self Declaration of the CE Marking for the European Union as specified in the above directive(s). WEEE Information on Disposal for Users of Waste Electrical & Electronic Equipment This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal. EN50131 Standards This component meets the requirements and conditions for full compliance with EN50131 series of standards for equipment classification. EN 50131-1:2006+A2:2017, EN 50131-3:2009, EN 50131-6:2008+A1:2014, EN 50131-10:2014, EN 50136-1:2012, EN 50136-2:2013, EN 60839-11-1:2013 Security Grade 4 Environmental Class II Equipment Class: Fixed Readers Environmental Class: IVA, IK07 SP1 (PSTN voice protocol) SP2 (PSTN digital protocol) SP6 (LAN Ethernet) and DP1 (LAN Ethernet + PSTN) SP6 (LAN Ethernet) and DP1 (LAN Ethernet + USB-4G modem) Tests EMC (operational) according to EN 55032:2015 Radiated disturbance EN 55032:2015 Power frequency magnetic field immunity tests (EN 61000-4-8) Cartridge Mortise Wireless Lock | Installation Manual 40 UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards. Cartridge Mortise Wireless Lock | Installation Manual 41 UL and ULC Installation Requirements Only UL / ULC listed compatible products are intended to be connected to a UL / ULC listed control system. CAN/ULC-60839-11-1 This card reader is CAN/ULC-60839-11-1 Listed for Class I applications only. Exit devices and wiring must be installed within the protected area. The card reader must be connected with shielded, grounded cable. Fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction

(AHJ) and shall not impair the operation of panic hardware and emergency egress. If fire resistance is required for door assembly, portal locking device(s) must be evaluated to ULC-S533 and CAN/ULC-S104. Must be installed with CAN/ULC-60839-11-1 Listed portal locking device(s) for ULC installations. Input power must be supplied by a Class 2 or power limited device. UL 294 This card reader is UL 294 Listed for Class 1 applications only. Exit devices and wiring must be installed within the protected area. The card reader must be connected with shielded, grounded cable. Fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction

(AHJ) and shall not impair the operation of panic hardware and emergency egress. If fire resistance is required for door assembly, portal locking device(s) must be evaluated to UL10B or UL10C. Must be installed with UL 1034 Listed electronic locks for UL installations. Input power must be supplied by a Class 2 or power limited device. A means of verification shall be employed by the user to enable access to the wireless electronic device such as a PIN or biometric feature, which subsequently provides access to the credential application software present on the wireless electronic device. The access control system shall have the means to distinguish between the type of credential used via code or description (e.g. authentication/digital signature keys received from a physical card vs. authentication/digital signature keys received from a wireless electronic credential.) UL 10C This lock is rated in Positive Pressure Fire Tests of Door Assemblies for resistance endurance of 3 hours. Cartridge Mortise Wireless Lock | Installation Manual 42 FCC Compliance Statements FCC PART 15, WARNINGS: INFORMATION TO USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not authorized by the party responsible for compliance could void the user's authority to operate this product. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Cartridge Mortise Wireless Lock | Installation Manual 43 Industry Canada Statement This class A digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada. CAN ICES-3 (A)/NMB-3(A) Cartridge Mortise Wireless Lock | Installation Manual 44 Disclaimer and Warranty Disclaimer: Whilst every effort has been made to ensure accuracy in the representation of this product, neither Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice. For warranty information, see our Standard Product Warranty. Cartridge Mortise Wireless Lock | Installation Manual 45 Designers & manufacturers of integrated electronic access control, security and automation products. Designed & manufactured by Integrated Control Technology Ltd. Copyright Integrated Control Technology Limited 2003-2023. All rights reserved. Disclaimer: Whilst every effort has been made to ensure accuracy in the representation of this product, neither Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice. www.ict.co 24-Jul-23

Labelonproductundertestthatwillbereplacedbythelabelonthepreviouspage Currentlylabelonproductthatwillbereplacedshowingthelocationofthelabelontheproduct

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co U.S. Agent Designation for Service of Process ATTENTION:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Integrated Control Technology Contact Name: Damon Standish Street Address: 6281 S Racine Cir, Suite 200 City/Province/Zip: Centennial, Co, 80111 Telephone No: 720-442-0767 Email: dstandish@ict.co FRN #: 0015106453 This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature:

Date: 7/13/2023 Signed by (Printed Name/Title): Damon Standish / President (ICT USA) The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Integrated Control Technology Limited Grantee Code: UAU FCC ID: UAUWIRELESSCML Contact Name: Hayden Burr Street Address: 4 John Glenn Ave, Rosedale City/Province/Zip: Auckland, 0632, New Zealand Telephone No: + 69 9 4767124 Email: hburr@ict.co Applicant Signature:

Date: 07 July 2023 Signed by (Printed Name/Title): Hayden Burr / Chief Executive Officer

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-07-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: UAUWIRELESSCML FRN: 0015106453 Integrated Control Technology Limited (the applicant) certifies that, as of the date of the filing of the application, Integrated Control Technology (USA) LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Integrated Control Technology Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Integrated Control Technology (USA) LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: Integrated Control Technology (USA) LLC Address: 6281 S Racine Cir, STE 200, Centennial, CO 80111 Contact Person: Damon Standish Email: dstandish@ict.co FRN: 0015106453 Sincerely, Integrated Control Technology Limited Hayden Burr Integrated Control Technology (USA) LLC Damon Standish

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co 7th of July 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mils Road Columbia, MD, 21046 United States of America SUBJECT: Attestation Statement, Rules 2.903(a), 2.906(d) and 2.907(c), Filings for FCC ID: UAUWIRELESSCML To whom it may concern,

(a) Integrated Control Technology (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to sections 2.903(a), 2.906(d) and 2.907(c), of the FCC rules. Integrated Control Technology (the applicant) certifies that as of the date of

(b) filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment Yours sincerely Hayden Burr. Chief Executive Officer Integrated Control Technology

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co 25th of July 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mils Road Columbia, MD, 21046 United States of America To whom it may concern CONFIDENTIALITY REQUEST - FCC ID: UAUWIRELESSCML Reference rule sections 0.457 (d) (ii) and pursuant to rule section 0.459 (a) confidentiality is requested as follows. Long Term Confidentiality:

Specific Information: Schematics, Block Diagram, Operational Description, Part List, Operational Description Antenna Location. The above information contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This Information should be treated as confidential for the duration of the Grant of Authorisation. Short Term Confidentiality:

Specific Information: Internal Photographs, Internal Photographs Antenna Location. The internal photographs contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This Information should be treated as confidential a period of 180 days from the time that the Grant of Authorisation is issued. Yours sincerely Hayden Burr. Chief Executive Officer Integrated Control Technology

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co 25th of July 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mils Road Columbia, MD, 21046 United States of America To whom it may concern CONFIDENTIALITY REQUEST - FCC ID: UAUWIRELESSCML Reference rule sections 0.457 (d) (ii) and pursuant to rule section 0.459 (a) confidentiality is requested as follows. Long Term Confidentiality:

Specific Information: Schematics, Block Diagram, Operational Description, Part List The above information contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This Information should be treated as confidential for the duration of the Grant of Authorisation. Short Term Confidentiality:

Specific Information: Internal Photographs The internal photographs contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This Information should be treated as confidential a period of 180 days from the time that the Grant of Authorisation is issued. Yours sincerely Hayden Burr. Chief Executive Officer Integrated Control Technology

Integrated Control Technology Limited 4 John Glenn Ave, Rosedale, Auckland 0632 P.O. Box 302-340, North Harbour, Auckland 0751 , New Zealand Toll Free: (0800) 428 111 Phone: +64 (9) 476 7124 Email:

sales@incontrol.co.nz www.ict.co 4th July 2023 SUBJECT:

FCC Authorization to Act on behalf of Integrated Control Technology Ltd. NZ. ID: UAUWIRELESSCML To whom it may concern, I hereby authorize Andrew Cutler, General Manager of EMC Technologies NZ Ltd to act on our behalf regarding the FCC Certification of the Integrated Control Technology Ltd for the registration of ICTs Clutched Deadbolt Wireless Lock product. Yours sincerely Hayden Burr. Chief Executive Officer Integrated Control Technology