PXOO7 1
The PXOO7 Proximity Card Reader has a slim door style mountable design to match any decor. The buried LED's and buzzer allow the PXOO7 Readers to be mounted indoors and out. The PXOO7 Reader Family accepts 4.75 to 14.25 Volts DC. The output formats like clock-and-data magstripe (ABA /
ISO7811 ), Wiegand and a number of other formats are determined by the personalization of the card and are emitted without customizing the Reader. The 5 Volt DC capability allows the replacement of older reader systems without rewiring or pulling new cables. The PXOO7 Family offers high reliability, consistent read characteristics and low power consumption. Within the PXOO7 Proximity Reader Family also models with a RS232/RS422/RS485 available for read and write operations. The PXOO7 Proximity Card Reader Family supports both the 125KHz and 13.56MHz technologies. Different models are available for EM4002, EM4050, HiTAG1 and 2, Mifare and I.Code silicon. Standard capabilities include Host system controlled red and green LED's and a buzzer. The PXOO7 Reader Family can be mounted on any surface without relevant performance degradation. Integrated Engineering is committed non-propriety, open Radio Frequent
(RFID) systems to the market demonstrated with the PXOO7 Proximity Reader Family. to bring Identification interface are Specifications Features Typical read PXO07BZ/HX PXO07AZ PXO07Z/MF PXO07Z/MFSNR PXO07Z/ICSNR range with an ISO Card HiTAG1, 2 EM4002, EM4050 Mifare Mifare serialnr. I.Code serialnr. 5- 10 cm 5- 10 cm 2 -3 cm 2- 5 cm 5- 15 cm Power Supply 4.75-
12.25 Volt DC Current Average Peak Interface Inputs Outputs requirements 50 mA 100 mA EMC Prot. 10Kohm pull-ups EMC Prot. open drain 0.5 A/max Dimensions 140 x 46 x 22 mm Material Black ABS housing with polyurethan potting Operating
-20 to 60 C temperature Certifications EN50022, CE, FCC Cable Distance 25 meter. Recommended stranded overall shield or equivalent. cable 8 x 0.35 conductor Mullion mounting The PXOO7 Readers are designed to be unobtrusive and can be mounted on a door mullion. Indications When a proximity card is decoded successfully with the card associated code is send to the Host system, the red LED flashes and the buzzer sounds a short 3KHz beep. Both LED's and the buzzer are also controllable by the Host system. the Connections The PXOO7 Reader Family has a flexible and reliable connector interface. The space for the cable and the connector within the PXOO7 housing can be poured with silicone to withstand harsh environmental conditions. Interface Coding The PXOO7 Reader Family can operate with any facility, system or card coding scheme. The output format, contents and length are determined by the personalization of the card. Output formats like magstripe, Wiegand and several others are available. Security Depending on the model and the silicon used the PXOO7 Reader Family offers high security challenge response schemes to protect the RFID air interface against simulations of cards. Parts List 1) PXO07 Reader 4.75-12.25 VDC 2) Terminal Connector 8 pins 3) Mounting sticker 4) Installation sheet 5) K25 spacer plate (optional) 6) Cable, 8 x 0.35 conductor qty 1 qty 1 qty 2 qty 1 qty 1 as required Installation 1) Determine an appropriate position for the instruction Reader and drill two holes for mounting the reader to the surface (see diagram). Make sure that enough room to connect the cable is allowed. Protect the cable against sharp edges and any damage from chaffing. 2) Remove the Terminal Connector 8 pins from the back of the Reader. Use a small flat head screwdriver to loosen off all of the terminals. The end of the cable should be prepared by cutting it back to expose the wires and each end should be twisted to eliminate any loose or frayed wires. 3) The wires should then be connected to the Reader inline with the Connector Assignments. 4) After wiring the reader and the Host system the Reader is ready to be tested. Apply power and present a Card to the Reader. The red LED should flash and the buzzer should beep indicating a read. If the Host system is connected to the red and green LED inputs these should follow the functionality of the Host system. 5) The Reader should now be secured to the surface using the appropriate stickers should be applied to cover the mounting holes. fasteners and the Mullion Mounting Assignments Connector PXOO7BZ/HX PXOO7AZ PXOO7Z/MF PXOO7Z/MFSNR PXOO7Z/ICSNR input input
<;::J Red LED
<;::J Green LED q Data / D1 q Clock
<;::J Buzzer
/ DO input 1 2 3 4 5 6 NC 7 8
<;::J Ground
<;::JPower PXOO7BZ/HX/RS232 PXOO7Z/MF/RS232 PXOO7Z/MFSNR/RS232 PXOO7Z/ICSN R/RS232 1 2 3 4 5 6 7 8 i input input
<:::J Red LED
<:::J Green LED q RS232 RTS (optiona~) q RS232 TXD
<:::J RS232 CTS (optionaO
<:::J RS232 RXD
<:::J Ground
<:::J Power PXOO7BZ/HX/RS422 PXOO7Z/MF/RS422 PXOO7Z/MFSNR/RS422 PXOO7Z/ICSNR/RS422 1 2 3 4 5 6 7 8 input input
? Red LED
? Green LED c::> RS422 TXB c::> RS422 TXA
? RS422 RXB
? RS422 RXA
? Ground
?Power Integrated Engineering Amsterdam The Netherlands Telephone: +31 204620755
+31 204620756 Fax:
info@ieprox.co$}
Email:
WWW:
http://www.iepr~x.com Ref: V1.2, 20/11/2000