Product Specifications ZigBee Module - ZiP E2.1-NSLB Revision 0.8 Mar 2015 Product Specifications ZiP E2.1-NSLB ZigBee Module Document History Date Author(S) Revision Comments Document History May-2014 May-2014 14-July-2014 23-July-2014 30-Sep-2014 Honky Yau Honky Yau Honky Yau Honky Yau Honky Yau 09-Feb-2015 Vincent Tse 04-Mar-2015 Vincent Tse 11-Mar-2015 Vincent Tse v0.1 v0.2 v0.3 v0.4 v0.5 v0.6 v0.7 v0.8 First release Update Block Diagram Confirmed SPI IOs pin assignment Update Contact Information Receiver input signal level Update 3.1 RF specification
- Naming: Maximum input signal level ->
Update Mechanical Dimension
- Module Height: from 3.0 to 2.9mm
- Module Height tolerance: from TBD to 2.9 +/- 0.15mm Updated Notice section Updated Notice & Ordering Guide Updated RF Spec Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 2 Product Specifications ZiP E2.1-NSLB ZigBee Module Document History Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 3 Product Specifications ZiP E2.1-NSLB ZigBee Module Contents Contents Contents ...................................................................................................................................................................... 4 1. Key Features .......................................................................................................................................................... 5 1.1. System Description ....................................................................................................................................... 5 1.2. Features ......................................................................................................................................................... 5 1.3. Block Diagram ............................................................................................................................................... 6 1.4. Module Pin Assignment ............................................................................................................................... 7 2. DC Electrical Specifications ............................................................................................................................... 10 2.1. Absolute Maximum Ratings ...................................................................................................................... 10 2.2. Power consumption .................................................................................................................................... 10 2.3. nRESET Pin Characteristics ..................................................................................................................... 10 3. Radio Performance .............................................................................................................................................. 11 3.1. RF Specifications ........................................................................................................................................ 11 4. Environmental Specifications ............................................................................................................................. 12 4.1. Environmental Specifications .................................................................................................................... 12 5. Mechanical ............................................................................................................................................................ 13 5.1. Physical Dimensions .................................................................................................................................. 13 5.2. Recommended PCB pattern ..................................................................................................................... 15 5.3. Label Drawing ............................................................................................................................................. 16 6. Ordering Guide ..................................................................................................................................................... 17 7. Notice..................................................................................................................................................................... 18 Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 4 Product Specifications ZiP E2.1-NSLB ZigBee Module 1. Key Features Key Features 1.1. System Description ZiP E2.1 is a ZigBee module targeting for Home Automation and Smart Energy marketplaces. The module embedded with a high performance Cortex M3 ZigBee transceiver EM3586 from Silicon Labs (SiLabs) which is fully compliant with IEEE 802.15.4-2003 specification. It provides a low cost, low power consumption and reliable wireless communication solution in the 2.4GHz ISM frequency band. Customer can implement applications easily with various interfaces provided by ZiP E2.1. 1.2. Features
- Dimensions: 27.20mm x 14.75mm x 2.90mm
- SiLabs Ember EM3586 high-performance, integrated ZigBee/802.15.4 chipset
- Transmit power up to 8dBm 1
- Receiver sensitivity: -100dBm
- Supply voltage: 2.4V to 3.6V
- Security: 128-bit AES
- On-board chip antenna
- Serial Interface: USB/SPI/UART/I2C
- ADC: 14bits ADC port
- FCC & RoHS compliant
- MSL JEDEC level 3 Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 5 Product Specifications ZiP E2.1-NSLB ZigBee Module 1.3. Block Diagram Key Features Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 6 Product Specifications ZiP E2.1-NSLB ZigBee Module 1.4. Module Pin Assignment Pin# Pin Name GND Reserved PC4/JTMS PB0/IRQA Key Features I/O Description Ground No connection
-
-
I/O Programmable I/O control, or JTAG mode select I/O Programmable I/O control, or an interrupt input 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PA3/SC2_nCS O Programmable I/O control, or External SPI serial flash, SPI nCS PB6/ADC1/IRQB I/O Programmable I/O control, or PC1/ADC3 I/O Programmable I/O control, or ADC input, or an interrupt input SWCLK/JTCK PC0/JRST/IRQD GND PB5/ADC0 GND GND GND GND Reserved GND RFO nRESET GND GND PA3 GND an ADC input JTAG/Serial Wire debugging port clock Programmable I/O control, or an interrupt input, or the JTAG reset input Ground Programmable I/O control, or an ADC input Ground Ground Ground Ground No Connection Ground RF output for external antenna (option) Module reset signal (Internal pull-up) Ground Ground Programmable I/O control Ground I I/O
-
I/O
-
-
-
-
-
-
O I
-
-
I/O
-
Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 7 Key Features Product Specifications ZiP E2.1-NSLB ZigBee Module Pin# Pin Name I/O Description 24 PC6/OSC32B I/O Programmable I/O control, or 32.768kHZ crystal 25 PC7/OSC32A I/O Programmable I/O control, or 26 SC1SCLK/PB3 I/O SPI port 1 clock, or 32.768kHz crystal programmable I/O control 27 PA0/USBDM/SC2MOSI O Programmable I/O control, or USB D- signal, or External SPI serial flash SPI master data out 28 PA1/USBDP/SC2MISO I Programmable I/O control, or USB D+ signal, or External SPI serial flash SPI master data in 29 30 VBATT PA2/SC2SCLK PWR Module power supply O Programmable I/O control, or 31 PA4/ADC4 I/O Programmable I/O control, or External SPI serial flash SPI master clock 32 33 GND PA5/ADC5/nBOOTMODE
-
I/O ADC input Ground Programmable I/O control, or ADC input, or Boot control, must be left open or pulled high during the reset to enable the normal firmware boot process. 34 SC1MISO(s)/SC1MOSI(m)/
I/O SPI port 1 MISO (slave)/ MOSI (master) signal, or TXD/
SC1SDA/
PB1 UART TXD signal, or I2C port 1 DATA signal, or Programmable I/O control 35 SC1MOSI(s)/SC1MISO(m)/
I/O SPI port 1 MOSI (slave)/ MISO (master) signal, or RXD/
SC1SCL/
PB2 UART RXD signal, or I2C port 1 CLK signal, or Programmable I/O control 36 PC2/JTDO/SWO I/O Programmable I/O control, or Serial Wire port OUTPUT signal, or JTAG data out Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 8 Product Specifications ZiP E2.1-NSLB ZigBee Module Pin# Pin Name I/O Description 37 SC1nSSEL/PB4 I/O SPI port 1 slave select, or Programmable I/O control 38 PC3/JTDI I/O Programmable I/O control, or Key Features 39 40 41 42 43 44 GND GND GND GND GND GND JTAG data in Ground Ground Ground Ground Ground Ground
-
-
-
-
-
-
Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 9 Product Specifications ZiP E2.1-NSLB ZigBee Module 2. DC Electrical Specifications 2.1. Absolute Maximum Ratings DC Electrical Specifications Parameters Supply voltage Voltage on any GPIO Test Conditions Min
-0.3 Max
+3.6
(VDDmax)
-0.3 VDDmax Unit V V Under no circumstances the absolute maximum ratings must be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the device. 2.2. Power consumption VCC = 3.0V, Temperature = 25oC, FRF= 2440MHz (unless otherwise noted) Parameters Condition Max Min Typ Unit Sleep mode Standby mode Receive mode Transmit mode
+8dBm 1 Serial controller current General purpose timer current General purpose ADC current Internal RC oscillator on Processor, radio, peripherals off Processor on Radio and peripherals off Radio receive chain on Cortex-M3 running at 24MHz For each controller at maximum data rate For each timer at maximum clock rate At maximum sample rate, DMA enabled 2.3. nRESET Pin Characteristics Parameters Reset pulse width to guarantee a reset 1.2 12 35 45.0 0.2 0.25 1.1 uA mA mA mA mA mA mA Min Typ 200 Max 300 Unit ns Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 10 Product Specifications ZiP E2.1-NSLB ZigBee Module 3. Radio Performance Radio Performance 3.1. RF Specifications VCC = 3.0V, Temperature = 25oC, Normal mode measured at 50ohm terminal load Parameters Test Conditions Min Typ
-1002
+81 Max 2475 2405
-40
+40 Unit MHz dBm dBm ppm Frequency range Receiver sensitivity Transmitter power at maximum Carrier frequency error Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 11 Product Specifications ZiP E2.1-NSLB ZigBee Module 4. Environmental Specifications Environmental Specifications 4.1. Environmental Specifications Parameters Operating supply voltage Operating Temperature Storage Temperature MSL Moisture Sensitivity Level RoHS Restriction of Hazardous Substances Min
+2.4
-40
-40 Unit V C C Max
+3.6
+85
+85 3 Compliant Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 12 Product Specifications ZiP E2.1-NSLB ZigBee Module 5. Mechanical 5.1. Physical Dimensions Mechanical Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 13 Product Specifications ZiP E2.1-NSLB ZigBee Module Mechanical
(Bottom view)
(Top view) Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 14 Product Specifications ZiP E2.1-NSLB ZigBee Module 5.2. Recommended PCB pattern Mechanical
(top view)
(top view) Notes:
To achieve best RF performance, it is recommended to follow the layout requirement as listed 1. The area in Zone1 (antenna area), all layers of customer circuit board should keep free from any metal objects 2. The area in Zone2, top layer of customer circuit board should have ground with no signal traces Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 15 Product Specifications ZiP E2.1-NSLB ZigBee Module 5.3. Label Drawing Mechanical Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 16 Product Specifications ZiP E2.1-NSLB ZigBee Module 6. Ordering Guide Ordering Guide Ordering Part Number P00-BI570NB-00M0 Description ZiP E2.1-NSLB 2.4GHz ZigBee module
(no PA version) Package Type Tape & Reel Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 17 Product Specifications ZiP E2.1-NSLB ZigBee Module 6. Ordering Guide Ordering Guide Ordering Part Number P00-BI570NB-00M0 Description ZiP E2.1-NSLB 2.4GHz ZigBee module
(no PA version) Package Type Tape & Reel Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 18 Product Specifications ZiP E2.1-NSLB ZigBee Module 7. Notice Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IC Statement This device complies with Industry Canada licence-exempt RSS-210 standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. France
Le prsent appareil est conforme aux CNR-210 d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, m me si le brouillage est susceptible d'en compromettre le fonctionnement. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AD7BBI570NB Or Contains FCC ID:
2AD7BBI570NB
Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 19 Product Specifications ZiP E2.1-NSLB ZigBee Module Notice When the module is installed inside another device, the user manual of this device must contain below warning statements:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 20 Notes Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 21 Contact Information Intercel (China) Limited Shenzhen Office Unit 6, 17/F, Vanta Industrial Centre, 21-33 Tai Lin Pai Road, Kwai Chung, New Territories, Hong Kong SAR, China t f
+852-2362 9018
+8522648 8806 Room 1303, 13/F, West Block, Tianan High-Tech Plaza Phase II, Tianan Cyber Park, Futian District, Shenzhen 518040, China t f
+86-755-8835 3778
+86-755-8835 2489 The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. IntercelTM assumes no responsibility for errors and omissions, and disclaims responsibility for IntercelTM assumes no any consequences resulting from the use of information included herein. Additionally, responsibility for the functioning of undescribed features or parameters. IntercelTM reserves the right to make changes without further notice. IntercelTM makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does IntercelTM assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all including without limitation consequential or incidental damages. IntercelTM products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the IntercelTM product could create a situation where personal injury or death may occur. Should Buyer purchase or use IntercelTM products for any such unintended or unauthorized application, Buyer shall indemnify and hold IntercelTM harmless against all claims and damages. liability, Intercel confidential This document is the sole and exclusive property of Intercel. Not to be distributed or divulged without prior written agreement. 22