FCC ID: EHAABTM3

Clarification about Compliance Insert The user manual information represents the ABTM3 radio within a typical final product. The Insert Sheets represents the data that will be included with all product that integrate the ABTM3 radio. OEM users will also be supplied with this information as well as information regarding requirements to verify the unintentional radiator emissions for final products that integrate the radio. The RF exposure report from Celltech shows no RF safety concerns. A statement on the users guide reflect the fact that the product was tested and the radio emissions comply to the RF exposure regulations.

Compliance Statement Insert Device Name: Pen Tablet Computer Model Number: Model 700 (710 & 720 Configurations) The responsible party for the compliance of this device is:

Intermec Technologies Corporation 6001 36th Avenue West Everett, WA 98203 USA

(425) 348-2600 CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the radio or television receiving antenna. Increase the separation between the computer equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Radio Frequency Exposure Compliance for ABTM3 radio, FCC ID: EHAABTM3 CANADA: XXXXXXXX This equipment has been tested and found to comply with the limits for products using radio transmitters used by the general public. 578-100-056 Revision A

*578-100-056*

578-100-056 Page 1 of 2 DECLARATION OF CONFORMITY

(According to ISO/IEC Guide 22 and EN 45014) PAGE ONE OF ONE THE PRODUCT HEREWITH COMPLIES WITH THE REQUIREMENTS OF :

THE LOW-VOLTAGE DIRECTIVE 72/32/EEC. THE EMC DIRECTIVE 89/336/EEC. Manufacturers Name:

Intermec Technologies Corporation 6001 36th Avenue West Everett, WA 98203 Declares that the product listed below:

European Representative:

Intermec International Incorporated Sovereign House, Vastern Road Reading, Berkshire RG1 8BT England ITE/Residential, Commercial, and Light Industrial Product Type:

Product Name: Model 700 Model Number: Model 700 Beginning Serial Number: All Options: All Date Issued: February 26, 2001 Conforms to the following product specifications:

Safety: IEC 950 / EN 60950 EMC: EN 55022 : 1994 + A1 : 1995 + A2 : 1997 / CISPR Publication 22 : 1993, Class B Limits and Methods EN 50024 : 1998 (CISPR 24) Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement EN 61000-4-2 : 1995 Electrostatic Discharge EN 61000-4-3 : 1995 Radiated RF Field EN 61000-4-4 : 1995 Electrical Fast Transients EN 61000-4-5 : 1995 Voltage Surge EN 61000-4-6 : 1996 Conducted RF Field EN 61000-4-11 : 1994 Voltage Dips, Short Interruptions, and Variations EN61000-3-2 : 1995 + A1 : 1998 + A2 : 1998 + A14 : 2000 Harmonic Current Emissions EN61000-3-3 : 1994 Voltage Fluctuation and Flicker I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s). Company Official: Arvin Danielson Position: Vice President Signature: Signed Copy on File Date: February 26, 2001 European Contact: Scott Mercer, Intermec International Incorporated, Sovereign House, Vastern Road, Reading, Berkshire, RG1 8BT England; Phone INT+44 118 987 9400; Fax INT+44 118 987 9401 578-100-056 Revision A

*578-100-056*

578-100-056 Page 2 of 2