Product Name: BT board Brand Name: Intermec Model No: INBT02 Users Guide 1 Introduction INBT02 is a Bluetooth Module. This can be made to connect to other Bluetooth wireless devices by integrating the INBT02 module to the users device for which Bluetooth functionality is targeted. The module block diagram is shown Figure 1 Figure 1: INBT02 - Block Diagram It consists of 3 main portions 1. Antenna Transmit/Receive RF Signal to/from other Bluetooth devices 2. BT Module BM 180 Used for Transmit/ Receive data to and from other Bluetooth devices 3. UART Interface Interface to the external UART host The BT Module is integrated to the printer by professional Installation, via the FFC which contains the UART interface to the host CPU, apart from some GPIO lines. It is a 14-pin connector as shown in photo in Figure 2. Figure 2: UART Interface - 14 Pin Connector 2 The Pin assignment is listed in Table 1. 1 Ground 3 5 7 9 11 13 Data_Exit Host_Sleep Ground UART_RTS UART_CTS Power, 3.3V Specifications Product Name Model Number Standard 2 4 6 8 10 12 14 Power, 3.3V Host_Wake BT_LED CMD_Data UART_TX UART_RX Ground Table 1.Connector Pin-out BT board INBT02 V2.1+EDR Frequency Band 2.4GHz ~ 2.48GHz Unlicensed ISM band Modulation Method FHSS (GFSK, /4 DQPSK, 8DPSK) Spread Spectrum Frequency Hopping Spread Spectrum Transfer rates (Max) 3Mbits/s RF Output Power 3 dbm (Transmission Typical) Antenna terminal NA Host Interface UART 4 wire interface to host (Rx, Tx, RTS, CTS) Supply Requirement 3.3 VDC, 0.1A Dimension 41.5mm (L)X 23mm(W) X 5.5mm(H) Operating Temperature
-10 ~ +50 C Storage Temperature
-20 ~ +60 C Humidity 10 ~ 90 % non-condensing The Number of Channels & Channel Spacing 79 channel, 1Mhz spacing Table 2: Specifications 3 Regulatory Information The Bluetooth radio is designed to be interoperable with any Bluetooth technology product that is based on frequency hopping spread spectrum (FHSS) radio technology and complies with the Bluetooth Specification Version 2.1. The Bluetooth radio, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Bluetooth radio device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of a Bluetooth radio device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following:
Using the Bluetooth radio equipment onboard airplanes, or Using the Bluetooth radio equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), ask for authorization to use the Bluetooth radio device before turning it on. 4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 5 This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID:EHA-INBT02 Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 6 Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
- EN 60950-1: 2006:+A11:2009+A1:2010+A12:2011 Safety of Information Technology Equipment
- EN50371 : 2002
- Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10 MHz - 300 GHz) -- General public
- EN 300 328 V1.7.1: 2006
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.9.2: 2011 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.1.1 2009 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment 7 esky
[Jm no vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se
[Czech]
zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk Undertegnede [fabrikantens navn] erkl rer herved, at f lgende udstyr
[Danish]
[udstyrets typebetegnelse] overholder de v sentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erkl rt [Name des Herstellers], dass sich das Ger t [Ger tetyp] in
[German]
bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti K esolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme
[Estonian]
t p = type of equipment] vastavust direktiivi 1999/5/E p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espa ol Por medio de la presente [nombre del fabricante] declara que el [clase de
[Spanish]
equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[name of manufacturer] [type of equipment]
[Greek]
1999/5/. Fran ais Par la pr sente [nom du fabricant] d clare que l'appareil [type d'appareil] est
[French]
conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente [nome del costruttore] dichiara che questo [tipo di
[Italian]
apparecchio] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of
[Latvian]
equipment / iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius
[Lithuanian]
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in Nederlands overeenstemming is met de essenti le eisen en de andere relevante
[Dutch]
bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
[Maltese]
jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. 8 Magyar Alulrott, [gy rt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz
[Hungarian]
alapvet k vetelm nyeknek s az 1999/5/EC ir nyelv egy b el r sainak. Polski Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z
[Polish]
zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugu s
[Nome do fabricante] declara que este [tipo de equipamento] est conforme
[Portuguese com os requisitos essenciais e outras disposi es da Directiva 1999/5/CE.
Slovensko
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami
[Slovenian]
in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky
[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky
[Slovak]
a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi
[Valmistaja = manufacturer] vakuuttaa t ten ett [type of equipment = laitteen
[Finnish]
tyyppimerkint ] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska H rmed intygar [f retag] att denna [utrustningstyp] st r I verensst mmelse
[Swedish]
med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999/5/EG. 9 Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 10 As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne, Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 1223A-INBT02. 11 Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 1223A-INBT022
Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. 12 Note: 1. 2.
XXXyyyLPDzzzz-x (NCC ID) 13