all | frequencies |
|
|
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 4 |
|
Compliance Insert | Users Manual | 1.01 MiB | ||||
1 2 3 4 |
|
Manual | Users Manual | 3.02 MiB | ||||
1 2 3 4 |
|
Radio Info | Users Manual | 68.56 KiB | ||||
1 2 3 4 |
|
User Manual part 1 | Users Manual | 2.26 MiB | ||||
1 2 3 4 |
|
User Manual part 2 | Users Manual | 2.47 MiB | ||||
1 2 3 4 |
|
User Manual part 3 | Users Manual | 1.34 MiB | ||||
1 2 3 4 |
|
User Manual part 4 | Users Manual | 1.07 MiB | ||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | Attestation Statements | |||||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | External Photos | |||||||
1 2 3 4 | RF Exposure Info | |||||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | Cover Letter(s) | |||||||
1 2 3 4 | RF Exposure Info | |||||||
1 2 3 4 | Test Report | |||||||
1 2 3 4 | Test Setup Photos |
1 2 3 4 | Compliance Insert | Users Manual | 1.01 MiB |
6820 Compliance Insert For Users in the United States and Canada Caution: This marking indicates that the user should read all included documentation before use. Attention: Ce marquage indique que lusager doit, avant lutilisation, lire toute la documentation incluse. Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the users authority to operate the equipment. Utilisateurs de ce produit sont aviss dutiliser des accessoires et des priphriques approuvs par Intermec Technologies Corporation. Lutilisation daccessoires autres que ceux recommands ou des changements ce produit qui ne sont pas approuvs par Intermec Technologies Corporation peuvent annuler la conformit de ce produit et mettre fin au droit qua lusager dutiliser l'quipement. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the radio or television receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance These Class B digital products meet all requirements of the Canadian Interference-Causing Equipment Regulations. Conformit aux normes canadiennes sur les appareils numriques Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Battery Information Increase the separation between the computer equipment and receiver. Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100C (212F). Do not short circuit; may cause burns. Keep away from children. Attention: Le bloc-piles utilis dans cet appareil peut prendre feu, constituer un risque de brlure chimique, exploser ou dgager des substances toxiques sil est manipul de faon inapproprie. Ne pas jeter au feu, dmonter ou chauffer plus de 100 C (212 F). Ne pas court-circuiter; cela pourrait causer des brlures. Garder hors de la porte des enfants. Battery Recycling Information This product contains or uses a lead acid battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Ce produit contient ou utilise une pile au plomb. Lorsque la batterie atteint la fin de sa dure de vie utile, la batterie uses doivent tre mises aux rebuts par un agent de recyclage ou un manipulateur de matriaux dangereux agr. Il ne faut pas mlanger la batterie aux autres dchets solides. Pour plus dinformations sur le recyclage ou la mise aux rebuts, contacter votre centre de services Intermec Technologies. Pb Pb Note: In the U.S.A., the EPA does not consider spent lead-acid batteries as hazardous waste. Power Supply Connections Caution: Use Intermec Model AE2 or AE27 for the power supply. No user-serviceable parts. Connexions du bloc dalimentation Attention: Employez le model dIntermec AE2 ou AE27 pour lalimentation dnergie. Il ne contient aucune pice parable par lutilisateur. Maximum Permissive Exposure (MPE) Radio Wave or Radio Frequency Maximum Permissive Exposure (MPE) for Model 6820 with Intermec mobile computers. When installing and using the Intermec 6820, a 20 cm (8 in) passing distance must be maintained from the body or head of the user or nearby persons and the device. This product meets FCC RF exposure guidelines when used with the Intermec accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. For Users Outside of the United States or Canada Caution: This marking indicates that the user should read all included documentation before use. The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the users authority to operate the equipment. Battery Information Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100C (212F). Do not short circuit; may cause burns. Keep away from children. Battery Recycling Information This product contains or uses a lead acid battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Pb Pb Power Supply Connections Caution: Use Intermec Model AE2 or AE27 for the power supply. No user-serviceable parts.
Intermec Technologies Corporation Intermec Technologies Corporation 100 C (212 F) Intermec Pb Pb Intermec AE2 AE27 Fr Benutzer auerhalb von Kanada oder den Vereinigten Staaten Vorsicht: Diese Kennzeichnung weist darauf hin, dass der Benutzer vor dem Gebrauch alle mitgelieferten Unterlagen lesen soll. Die Benutzer dieses Produkts werden darauf hingewiesen, nur Zubehrteile und Peripheriegerte zu verwenden, die von Intermec Technologies Corporation genehmigt sind. Falls nicht empfohlene Zubehrteile verwendet oder an diesem Produkt nderungen vorgenommen werden, die nicht von Intermec Technologies Corporation genehmigt sind, kann dadurch die behrdliche Konformitt des Produkts verletzt werden und der Benutzer die Berechtigung zur Verwendung des Gerts verlieren. Akku-Informationen Vorsicht: Der in diesem Gert verwendete Akkusatz kann sich bei Missbrauch entznden, chemische Vertzungen verursachen, expoldieren oder toxische Substanzen freisetzen. Nicht verbrennen, zerlegen oder ber 100 C (212 F) erwrmen. Keinen Kurzschluss verursachen; Verbrennungsgefahr. Von Kindern fern halten. Informationen zum Recycling von Batterien Dieses Produkt enthlt oder verwendet einen Bleisureakku. Wenn die Batterie ausgedient hat, sollte sie durch einen qualifizierten Recycler oder durch den Sondermll entsorgt werden. Werfen Sie die Batterie nicht in den Abfall. Setzen Sie sich mit Ihrem Intermec Technologies Service-Zentrum in Verbindung, um weitere Informationen zum Recycling oder Entsorgen zu erhalten. Pb Pb Stromanschlsse Vorsicht: Als Netzteil Intermec Modell AE2 oder AE27 verwenden. Enthlt keine Teile, die vom Benutzer gewartet werden knnen.
: . Intermec Technologies Corporation . Intermec Technologies Corporation ,
. 100C (212 F) . . . ,
. . Intermec . Pb Pb
: Intermec AE2 AE27 . . Para usurios fora do Canad ou dos Estados Unidos Cuidado: Esta identificao indica que o usurio deve ler toda a documentao fornecida antes do uso. Se advierte a los usuarios de este producto que usen accesorios y perifricos aprobados por Intermec Technologies Corporation. El uso de accesorios aparte de los recomendados, o los cambios a este producto que no estn aprobados por Intermec Technologies Corporation, pueden anular el cumplimiento de este producto y ocasionar la prdida de la autorizacin del usuario para operar el equipo. Informaes sobre a bateria Cuidado: A bateria utilizada neste dispositivo pode pegar fogo, criar risco de queimadura qumica, explodir ou exalar materiais txicos se abusada. No incinerar, desmontar nem aquecer a bateria a mais de 100C (212F). No provocar curto-circuito, pois pode causar queimaduras. Manter afastada de crianas. Infomaes de Reciclagem de Bateria Este produto contm ou usa bateria chumbo-cido. Quando a bateria chega ao fim da sua vida til, deve ser descartada por um profissional de reciclagem qualificado ou por um especialista no manuseio de materiais perigosos. No misture a bateria com fluxo de lixo slido. Entre em contato com seu Centro de Servios de Tecnologia Intermec para informaes de reciclagem ou descarte. Pb Pb Conexes da fonte de alimentao Ciudado: Usar fontes de alimentao Intermec Modelo AE2 ou AE27. No h nenhuma pea que possa ser substituda ou consertada pelo usurio.
, , Intermec Technologies Corporation. , ,
, Intermec Technologies Corporation,
. , , 100C (212 F). .
. - Intermec Technologies. Pb Pb
: Intermec AE2 AE27. ,
, . Para usuarios fuera de Canada o de los Estados Unidos Precaucin: Esta marca indica que el usuario debe leer toda la documentacin incluida antes del uso. Os usurios deste produto devem usar acessrios e perifricos aprovados pela Intermec Technologies Corporation. Usar acessrios no recomendados, ou fazer alteraes neste produto no aprovadas pela Intermec Technologies Corporation, poder anular a conformidade deste produto e resultar na perda da permisso do usurio de utilizar o equipamento. Informacin de la batera Precaucin: La batera que se usa en este dispositivo puede encenderse, crear un peligro de quemadura qumica, explotar o expedir materiales txicos si se trata indebidamente. No la incinere, desarme ni caliente sobre 100C (212F). No haga cortocircuitos porque pueden causar quemaduras. Mantngala alejada de los nios. Informacin acerca del reciclaje de la batera Este producto contiene o usa una batera de cido de plomo. Cuando la batera llega al final de su vida til, debe ser desechada por personal especializado en reciclaje de materiales o manejo de materiales peligrosos. No mezcle la batera con otros residuos slidos. Pnganse en contacto con su Centro de servicio de Intermec Technologies para obtener informacin sobre reciclaje o desecho de materiales. Pb Pb Conexiones de la fuente de alimentacin Precaucin: Para la fuente de alimentacin use el Modelo AE2 o AE27 de Intermec. No hay piezas a las cuales pueda dar servicio el usuario. Worldwide Headquarters Worldwide Headquarters 6001 36th Avenue West 6001 36th Avenue West Everett, Washington 98203 Everett, Washington 98203 U.S.A. U.S.A. tel 425.348.2600 tel 425.348.2600 fax 425.355.9551 fax 425.355.9551 www.intermec.com www.intermec.com 2008 Intermec Technologies 2006 Intermec Technologies Corporation. All rights reserved. Corporation. All rights reserved. 6820 Compliance Insert
*933-059-004*
P/N 933-059-004
1 2 3 4 | Manual | Users Manual | 3.02 MiB |
PW50 Workboard Printer Placeholder for PW50 illustration Users Guide Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation. Information and specifications contained in this document are subject to change without prior notice and do not represent a commitment on the part of Intermec Technologies Corporation. 2007 by Intermec Technologies Corporation. All rights reserved. The word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook, CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, i-gistics, INCA (under license), Intellitag, Intellitag Gen2, JANUS, LabelShop, MobileLAN, Picolink, Ready-to-Work, RoutePower, Sabre, ScanPlus, ShopScan, Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation. There are U.S. and foreign patents as well as U.S. and foreign patents pending. ii PW50 Workboard Printer Users Guide Contents Contents Before You Begin. v Safety Information . v Global Services and Support . v Warranty Information. v Web Support . vi Telephone Support . vi Service Location Support . vi Who Should Read This Manual . vii Related Documents . vii 1 Using the PW50 Workboard Printer. 1 Learning About the PW50 Workboard Printer . 2 Identifying the Parts of the Printer . 2 Understanding the Control Panel . 3 Understanding the Printer Sounds . 5 Using the Batteries . 5 Installing the Battery . 6 Charging the Batteries. 6 Understanding the Battery LED . 7 Extending Battery Life. 8 Loading Media. 8 Printing a Testprint . 10 Inserting a Handheld Computer. 11 Using the Card Reader Option . 12 2 Configuring the PW50. 13 Configuring the PW50 . 14 Understanding the Printer Modes . 14 Understanding Ready Mode . 14 Understanding Pause Mode. 14 Understanding Error Mode . 14 Understanding Test Mode . 14 PW50 Workboard Printer Users Guide iii Contents Changing Configuration Settings . 16 Changing Configuration Settings From PrintSet . 17 Changing Configuration Settings Using the Command Line . 17 Changing Configuration Settings From SmartSystems Console. 17 Establishing Communications With a Host . 18 Setting Up Bluetooth Communications. 18 Setting Up USB Communications . 19 Setting Up Serial Communications . 20 Upgrading the Firmware. 21 Downloading Fonts and Graphics . 22 3 Troubleshooting and Maintaining the PW50 . 23 Troubleshooting the PW50 . 24 Contacting Product Support. 24 Understanding Error Messages . 25 Troubleshooting Printer Problems and Finding Solutions . 25 Troubleshooting Communication Problems . 27 Cold Booting the PW50 . 28 Cleaning the PW50. 28 A Specifications . 31 Specifications. 32 Accessories for the PW50 . 36 iv PW50 Workboard Printer Users Guide Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions. This section explains how to identify and understand warnings, cautions, and notes that are in this document. A warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury to the persons working on the equipment. A caution alerts you to an operating procedure, practice, condition, or statement that must be strictly observed to prevent equipment damage or destruction, or corruption or loss of data. Note: Notes either provide extra information about a topic or contain special instructions for handling a particular condition or set of circumstances. Global Services and Support Warranty Information To understand the warranty for your Intermec product, visit the Intermec web site at www.intermec.com and click Support >
Returns and Repairs > Warranty. PW50 Workboard Printer Users Guide v Before You Begin Disclaimer of warranties: The sample code included in this document is presented for reference only. The code does not necessarily represent complete, tested programs. The code is provided as is with all faults. All warranties are expressly disclaimed, including the implied warranties of merchantability and fitness for a particular purpose. Web Support Visit the Intermec web site at www.intermec.com to download our current manuals (in PDF). To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor. Visit the Intermec technical knowledge base (Knowledge Central) at www.intermec.com and click Support > Knowledge Central to review technical information or to request technical support for your Intermec product. Telephone Support In the U.S.A. and Canada, call 1-800-755-5505. Outside the U.S.A. and Canada, contact your local Intermec representative. To search for your local representative, from the Intermec web site, click About Us > Contact Us. Service Location Support For the most current listing of service locations, click Support
>Returns and Repairs > Repair Locations. For technical support in South Korea, use the after service locations listed below:
AWOO Systems 102-1304 SK Ventium 522 Dangjung-dong Gunpo-si, Gyeonggi-do Korea, South 435-776 Contact: Mr. Sinbum Kang Telephone: +82-31-436-1191 Email: mjyun@awoo.co.kr vi PW50 Workboard Printer Users Guide Before You Begin IN Information System PTD LTD 6th Floor Daegu Venture Center Bldg 95 Shinchun 3 Dong Donggu, Daegu City, Korea E-mail: jmyou@idif.co.kr or korlim@gw.idif.co.kr Who Should Read This Manual This users guide is for the person who is responsible for installing, configuring, and maintaining the PW50 Workboard Printer. This users guide provides you with information about the features of the PW50, and how to configure, operate, maintain, and troubleshoot it. Before you work with the PW50, you should be familiar with your network and general networking terms, such as IP address. Related Documents The Intermec web site at www.intermec.com contains our documents (as PDF files) that you can download for free. To download documents 1 Visit the Intermec web site at www.intermec.com. 2 Click Support > Manuals. 3 In the Select a Product field, choose the product whose documentation you want to download. To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor. PW50 Workboard Printer Users Guide vii Before You Begin viii PW50 Workboard Printer Users Guide 1 Using the PW50 Workboard Printer Use this chapter to familiarize yourself with the PW50 Workboard Printer. This chapter contains these sections:
Learning About the PW50 Workboard Printer Using the Batteries Loading Media Printing a Testprint Using the Card Reader Option Inserting a Handheld Computer 1 Chapter 1 Using the PW50 Workboard Printer Learning About the PW50 Workboard Printer The PW50 is a rugged direct thermal label and receipt printer that is designed for use with the CN3, CN3e, and CK61 mobile computers. The PW50 provides:
print resolution of 203 dpi. print speeds of up to 100 mm per second (4 ips). a Bluetooth radio. Identifying the Parts of the Printer Use this illustration to familiarize yourself with some of the features of the PW50. Feed button Standby button Battery Intermec Ready-to-Work indicator Error Media cover release button Communications PW50 Printer: This illustration shows the important features of the PW50 printer. A weather-resistant flap protects the communcations ports and the external power connector. 2 PW50 Workboard Printer Users Guide Understanding the Control Panel Chapter 1 Using the PW50 Workboard Printer The PW50 control panel contains two buttons and four LED indicators. Use the two buttons to perform functions on the PW50 printer. See the following tables to understand the buttons and LED indicators. Standby button Communications Error Feed button Battery Intermec Ready-to-Work indicator PW50 Control Panel: Use this illustration to familiarize yourself with the buttons and LEDs on the PW50. Understanding How to Use the PW50 Buttons Button Name Standby
(Power) Feed Functions Press to put the printer in Standby mode. In Standby mode, power to the radio is turned off. Press to turn the printer back on and put the printer in Ready mode. Press to advance label or receipt paper. The amount of media that feeds depends on the type of media you are using. Media advances by 5 mm (0.2 inch), feeds out an entire label, or feeds a configured length of media based on your media and settings. If the printer is printing, pressing this button causes pauses printing. Press the button again to resume printing. PW50 Workboard Printer Users Guide 3 Chapter 1 Using the PW50 Workboard Printer Understanding the Communications, Error, and Battery Indicators Indicator Name State Communications Off Description The Bluetooth radio is off. The Bluetooth radio turns off when you connect a serial cable. Steady green The Bluetooth radio is on and the printer is not connected to a serial cable. The PW50 is off. Error Off Battery Steady green Ready/Data Steady red Off Error The battery is installed and working properly. There is no battery installed. Steady green Battery is fully charged in the PW50 with an external power supply connected. Battery is charging in the PW50 with an external power supply connected. Steady red Blinking red Battery is low. Understanding the Intermec Ready-to-Work Indicator State Off On Blinking A blinking light can mean one of several conditions:
Description The PW50 is in Standby mode. The PW50 is powered on and operating. The printer is out of paper. The media cover is open. There is a printer error that requires you to perform an action. For a list of possible problems, see Chapter 3, Troubleshooting and Maintaining the PW50. 4 PW50 Workboard Printer Users Guide Chapter 1 Using the PW50 Workboard Printer Understanding the Printer Sounds The PW50 plays sounds in response to several actions that you can take with the printer. Use the following table to understand when the sounds occur and what they mean. Understanding the Printer Sounds Sound Power Occurs When:
You insert a battery in the printer. The PW50 starts charging the battery. You plug in the AC adapter. Hardware You open the media door, close the media door, or insert a cable. Button Error You press one of the PW50 buttons. The printer cannot feed paper or print a job because of a hardware issue such as the media door open, a paper jam, or there is no media. An error occurs such as a paper jam, a print error, or the printer is out of range. Using the Batteries The PW50 uses a rechargeable 2200 mAh lithium-ion battery (Model AB13) for power. You must fully charge the battery before you can use the PW50. A fully charged battery can last up to one week without needing to be recharged when the printer is in Standby mode. Use Intermec Model AB13 battery only. Use of another battery may present a risk of fire or explosion. The Model AB13 battery may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100C
(212F), or incinerate. Dispose of used batteries promptly. Keep away from children. PW50 Workboard Printer Users Guide 5 Chapter 1 Using the PW50 Workboard Printer Installing the Battery Make sure you fully charge the battery before you use your PW50. You can charge the battery before or after you install them into the PW50. To install the battery 1 Lay the PW50 upside down on a flat surface. 2 Insert the battery with the tab facing away from the front control panel. 3 Insert the edge of the battery under the lip of the PW50 and then push down until you hear the battery latch click. Charging the Batteries There are two ways to charge the PW50 battery:
Connect AC power to the printer and charge the battery while it is in the PW50. Charge the battery in the AC18 4-bay battery charger. 6 PW50 Workboard Printer Users Guide Chapter 1 Using the PW50 Workboard Printer For information on charging your battery in the 4-bay battery charger, see the AC18 4-Bay Battery Charger Instructions
(P/N 943-128-xxx). It takes approximately 6 hours to charge the battery while it is installed in the PW50 printer. To charge the battery inside the PW50, you need:
an Intermec 12 VDC power supply (Model 073573 or Model AE19). an AC power cord. To charge the battery inside the PW50 1 Install the battery in the PW50. For help, see the previous section, Installing the Battery on page 6. 2 Connect the power supply to the DC power connector on the printer. 3 Connect one end of the power cord to the power supply, and then plug the other end into an AC outlet. Understanding the Battery LED The easiest way to tell the status of your battery is to look at the battery LED on the control panel of the PW50. Battery LED Status LED State Steady green Steady red Blinking red Off Status Battery is fully charged in the PW50 with an external power supply connected. Battery is charging in the PW50 with an external power supply connected. Battery is low. The battery is installed and working properly. There is no battery installed. PW50 Workboard Printer Users Guide 7 Chapter 1 Using the PW50 Workboard Printer Extending Battery Life Here are some tips for extending the overall life of your battery:
Never expose the battery to direct sunlight or temperatures over 40C (104F). Only charge the battery inside the PW50 using a power supply or in the 4-bay battery charger (Model AC18). Here are some tips for extending the life of your battery between charges:
Press the Standby button to put the printer in Standby mode. Remove the battery from the printer if you are not going to use it for three or more days. Do not operate the PW50 in extremely cold temperatures. Using the PW50 in temperatures below freezing reduces the overall battery life. Remember that any rechargeable battery loses its ability to maintain a charge over time. You can only recharge it a finite number of times before you must replace it. Loading Media You can use roll or fanfold receipt media with the PW50 printer. The PW50 ships with a small amount of media loaded and a test page printed to verify that the printer works. For information on media specifications, see Specifications on page 32. 8 PW50 Workboard Printer Users Guide Chapter 1 Using the PW50 Workboard Printer To load media 1 Press down on the blue media cover release button until the cover releases. 2 Insert a roll of media. Make sure you load the media clockwise so that it pulls off the core from the bottom of the printer. 3 Pull out approximately 8 cm (3 inches) of the media. PW50 Workboard Printer Users Guide 9 Chapter 1 Using the PW50 Workboard Printer 4 Close the media cover and press down on the cover until it latches. The printer emits the hardware sound to tell you that the media door closed correctly. 5 Press the Feed button to advance the media. Printing a Testprint After you load media in the printer, you are ready to print a testprint. If you cannot get the testprint information to print, see Chapter 3, Troubleshooting and Maintaining the PW50. To print a testprint 1 Press and hold the Standby and Feed buttons until the PW50 beeps. 2 Release the buttons. 3 The PW50 prints a testprint. 10 PW50 Workboard Printer Users Guide Inserting a Handheld Computer Chapter 1 Using the PW50 Workboard Printer The PW50 is designed for use with the CN3, CN3e, and CK61 mobile computers. To insert a handheld computer Slide the computer into the slot on the PW50 until the computer snaps into place. This illustration shows inserting a CN3. However, the PW50 is also designed for use with the CN3e and CK61 mobile computers. PW50 Workboard Printer Users Guide 11 Chapter 1 Using the PW50 Workboard Printer Using the Card Reader Option You can order the PW50 with a card reader option. I need information about the card reader option. 12 PW50 Workboard Printer Users Guide 2 Configuring the PW50 This chapter describes how to configure the PW50 and contains these sections:
Configuring the PW50 Establishing Communications With a Host Upgrading the Firmware Downloading Fonts and Graphics 13 Chapter 2 Configuring the PW50 Configuring the PW50 You can change the configuration settings of the PW50 printer by sending commands from your PC or remotely from the SmartSystems console. Understanding the Printer Modes The PW50 has seven modes to help you effectively interact with the printer: Ready, Paused, Error, Test, and Upgrade. Use the following sections to understand the different printer modes Understanding Ready Mode The printer is in Ready mode when the printer is on and ready to print. Understanding Pause Mode Use Pause mode to momentarily stop printing or to cancel a current print job. Use the Feed button to both pause and resume printing. To enter Pause mode Press the Feed button while the printer is printing. To resume printing Press the Feed button while the printer is paused. To cancel a print job 1 Press the Feed button to pause printing. 2 Press the Feed button again to cancel the print job. Understanding Error Mode The printer enters Error mode when it detects an error condition such as a low battery or a paper fault. Understanding Test Mode Use Test mode to verify printer settings, print test labels, restore factory default settings, or enter Dump mode for troubleshooting purposes. Two test modes are available: Test mode and Extended Test mode. 14 PW50 Workboard Printer Users Guide Chapter 2 Configuring the PW50 Using Test Mode Test mode is a simple sequence of events which requires little user interaction. Extended Test mode requires more user interaction and lets you choose which actions you want the printer to perform. To enter Test mode 1 Make sure the printer is in Ready mode and is loaded with media. 2 Press and hold the Standby and Feed buttons until the PW50 beeps. 3 Release the buttons. The printer performs a test feed (sensor calibration), prints a series of test labels, and then enters Dump mode. While the printer is in Dump mode, it scans the communication ports. Any characters received on the communication ports are printed. 4 Press Feed to exit Dump mode. After you exit Dump mode, the printer returns to Ready mode. For more information on Dump mode, see Troubleshooting Communication Problems on page 27. Using Extended Test Mode Use Extended Test mode to run additional diagnostic tests, including printing specific test labels, entering Dump mode, and resetting to factory defaults. To enter Extended Test mode 1 Make sure that the printer is loaded with media. 2 Press the media cover release button to open the media cover. 3 Press the Standby button to turn the printer off. 4 Press and hold the Standby and Feed buttons until the PW50 beeps. PW50 Workboard Printer Users Guide 15 Chapter 2 Configuring the PW50 5 Close the media cover. You are now in Extended Test mode. Press and hold the Feed button for at least 2 seconds to cycle through the Extended Test mode option. Press and release the Feed button select an Extended Test mode option. Options in Extended Test Mode Option Select Media Test Labels Dump Mode Description This option is similar to the process in Test mode, except that the printer performs a slow test feed in Extended Test mode. The slow test feed enables the printer to perform a slow sensor calibration, which can help resolve gap or mark detection problems. This option allows you to print test labels one at a time. Press the Feed button to print the next label. This option enters Dump mode. For more information on Dump mode, see Troubleshooting Communication Problems on page 27. Factory Default This option restores the factory default settings. Press the Setup and Exit Exit Feed button to select this option. This option exits Extended Test mode and puts the printer in Setup mode. This option exits Extended Test mode. Changing Configuration Settings There are several ways you can change the configuration settings of the printer. You can change the configuration settings:
from the host PC using PrintSet. from the host PC using the command line. from the SmartSystems Console. 16 PW50 Workboard Printer Users Guide Chapter 2 Configuring the PW50 Changing Configuration Settings From PrintSet PrintSet Version 4.2 (or later) is a printer configuration tool that you can download from the Intermec web site. PrintSet can communicate with your printer through a serial cable or a network connection. It works on all PCs running Windows 98 (or later). PrintSet allows you to easily change all of the setup parameters. It also includes setup wizards to guide you through some common configuration tasks. Does PrintSet version 4.2 support the PW50? When will it be released?
Changing Configuration Settings Using the Command Line You can change configuration parameters by sending commands directly to the printer using your terminal program (HyperTerminal) and a serial or network connection. What ESC-P command do you send? Does ESC-P automatically send feedback to HyperTerminal?
For more information on how to change configuration settings, see the ESC-P Programmers Reference Manual (P/N 937-005-xxx), available from the Intermec web site at www.intermec.com. Changing Configuration Settings From SmartSystems Console You can use the SmartSystems Console to change configuration settings on your printer. The PW50 ships with the SmartSystems client loaded on it. The console is part of SmartSystems Foundation and is available from the Intermec web site. To download SmartSystems Foundation, go to www.intermec.com/products/
smrtsysfoundation/index.aspx. PW50 Workboard Printer Users Guide 17 Chapter 2 Configuring the PW50 Establishing Communications With a Host The PW50 must establish communications with a host that will send the data for the printer to print. The PW50 provides four ways to communicate with a host:
Bluetooth radio communications USB communications Serial communications through a serial cable or directly to an Intermec computer inserted in the PW50 Setting Up Bluetooth Communications The PW50 contains a Bluetooth radio that allows wireless communications with a remote device from distances up to 100 meters (approximately 328 feet) depending on the Bluetooth range capabilities of the remote device, environmental conditions, and obstructions. For the Bluetooth-enabled devices to exchange data, both devices must establish a connection. Bluetooth software is always running in the background. The PW50 cannot initiate a Bluetooth connection. One of the devices, such as a CN3 mobile computer, must request a connection with the printer. The PW50 then accepts or rejects the connection. Use Intermec Settings on the mobile computer to enable the Bluetooth settings on the PW50. The PW50 can also connect to Bluetooth scanners such as the SF51 and the SR61. You can create the bar code labels you need to connect the printer to a Bluetooth scanner using EasySet software. If you are going to create the bar code labels using EasySet, you will need to know the Bluetooth Device Address and the PIN of the PW50. You can download EasySet at no charge from the Intermec web site at www.intermec.com. Each PW50 equipped with a Bluetooth radio has a unique Bluetooth Device Address (BDA) loaded into its module when manufactured. You can find the BDA on the certification label located on the bottom of the printer. 18 PW50 Workboard Printer Users Guide Chapter 2 Configuring the PW50 To set up Bluetooth communications with a mobile computer Follow the procedure to discover and connect to Bluetooth devices in your mobile computer users manual. Note: For maximum security, you need to configure a Bluetooth passcode for the PW50. The default passcode for the PW50 is 1234. To set up Bluetooth communications with a scanner 1 Download and install EasySet. 2 Create the following bar code labels using EasySet:
Administrator reset factory defaults Bluetooth parameters - security - not active Bluetooth parameters - connect/disconnect - compose BT address Bluetooth parameters - security - compose PIN:
3 Scan the bar code labels with the Bluetooth scanner. Understanding the Communications Indicator State Off Description The Bluetooth radio is off. The Bluetooth radio turns off when you connect a serial cable. Steady green The Bluetooth radio is on and the printer is not connected to a serial cable. Setting Up USB Communications a USB cable. Intermec InterDriver software. To set up USB communications with your PC, you need:
You can download the InterDriver software from the Intermec web site at www.intermec.com. PW50 Workboard Printer Users Guide 19 Chapter 2 Configuring the PW50 Setting Up Serial Communications Use a serial cable (P/N 075497-001) to connect the PW50 to a PC, or insert a CN3, CN3e, or CK61 mobile computer. Before you can establish a serial connection, you need to make sure that the settings on the PC or mobile computer match the settings on the PW50. Serial Port Default Settings on the PW50 Parameter Baud rate Data bits Parity Stop bits Flow control Default Setting 115200 8 None 1 Hardware To connect the PW50 to a PC 1 Connect the 8-pin circular DIN connector to the serial port on the PW50. 2 Connect the other end of the serial cable to a serial port on the back of your PC or to a serial adapter on your mobile computer. Serial cable Serial port 20 PW50 Workboard Printer Users Guide Upgrading the Firmware Chapter 2 Configuring the PW50 The latest firmware and software is always available for download from the Intermec web site at www.intermec.com. To download firmware updates 1 Go to the Intermec web site at www.intermec.com. 2 Click Support > Downloads. 3 In the Select a Product field, choose PW50 mobile printer. The latest available software displays on the page. 4 Download the latest firmware version to your computer. Make sure you choose the correct firmware upgrade for your printer. 5 Extract the .zip file to a folder on your computer. You use PrintSet to upgrade the printer firmware. Your printer should reboot after you finish upgrading the firmware. If it does not reboot, you need to cold boot the printer. For help, see Cold Booting the PW50 on page 28. To upgrade your printer firmware 1 Download the latest version of PrintSet from the Intermec web site at www.intermec.com. 2 Select File > Add Printer to start the Add Printer Wizard which guides you through the process of adding your printer. 3 Select your printer under My Printers and then go to Printer >
Firmware Wizard. The Firmware Wizard guides you through the necessary steps to upgrade your firmware. To upgrade your printer using a serial connection 1 Make sure you have established a serial communications between your PC and the PW50. For help, see Setting Up Serial Communications on page 20. 2 Use ESC-P commands to send the upgrade file to the printer. For help with ESC-P commands, see the ESC-P Programmers Reference Manual (P/N 937-005-xxx) available from the Intermec web site at www.intermec.com. PW50 Workboard Printer Users Guide 21 Chapter 2 Configuring the PW50 Downloading Fonts and Graphics The easiest way to download fonts and graphics is to use the free Intermec printer application called PrintSet. You can download PrintSet from the downloads page for the PW50 printer on the Intermec web site at www.intermec.com. Follow the procedures in the PrintSet online help to download fonts and graphics. You can also use ESC/P commands to send fonts and graphics to the printer. For help with commands and information, see the ESC-P Programmers Reference Manual (P/N 937-005-xxx) available from the Intermec web site at www.intermec.com. 22 PW50 Workboard Printer Users Guide 3 Troubleshooting and Maintaining the PW50 This chapter contains information to help you solve problems you may encounter while using the PW50 and contains these sections:
Troubleshooting the PW50 Cold Booting the PW50 Cleaning the PW50 23 Chapter 3 Troubleshooting and Maintaining the PW50 Troubleshooting the PW50 You may have printer operation, print quality, or printer communication problems at some time during the life of the PW50 printer. It is easy to fix most of the problems and you will find solutions in Troubleshooting Printer Problems and Finding Solutions on page 25. If you cannot find the answer to your problem, you may need to contact Product Support. Contacting Product Support Before you call Intermec Product Support, you may want to visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support. To talk to an Intermec Product Support representative in the U.S.A. or Canada, call:
1-800-755-5505 Outside the U.S.A. and Canada, go to www.intermec.com and click Contact to find your local Intermec representative. Before you call Intermec Product Support, make sure you have the following information ready:
Printer serial number Firmware type and version Bluetooth, wireless, or serial port settings You can find all of the information listed above in the printer menu system or on a test print page. 24 PW50 Workboard Printer Users Guide Understanding Error Messages Chapter 3 Troubleshooting and Maintaining the PW50 Use the following tables to troubleshoot common errors. To receive error messages, you need to tunrn on the Allow Messages From Printer command. For help, see the ESC-P Programmers Reference Manual (P/N 937-005-xxx). PW50 Error Message Descriptions Error Message Lid_Open Paper_Out Voltage Description The media cover is open. Close the media cover and press down until it latches. If Lid_Open=Y, the printer detected an error condition and canceled any pending print jobs. The printer is out of media. Load a new roll of media. If Lid_Open=Y, the printer detected an error condition and canceled any pending print jobs. This message indicates the power status of the printer:
If Voltage=H, the printer is fully powered by either an external power supply or a fully charged battery. If Voltage=L, the printer has detected a low voltage condition. Connect the printer to external power, or insert a fully charged charged battery. Troubleshooting Printer Problems and Finding Solutions Use the following tables to troubleshoot some common problems you may encounter with the PW50 printer. Printer Problems and Possible Solutions Problem The printer does not turn on when you press Standby. The blue light
(Intermec Ready-to-
Work indicator) is blinking. Possible Solution Replace the battery with a charged battery. Connect external power to make sure the printer works correctly and to charge the battery. Make sure media is loaded and the media cover is closed. For help, see Loading Media on page 8. There is a printing error. The printer is paused. The printer is canceling a print job. PW50 Workboard Printer Users Guide 25 Chapter 3 Troubleshooting and Maintaining the PW50 Printer Problems and Possible Solutions (continued) Problem Printer keeps printing or feeding when it should stop. The printout is not in the desired position. The printer is not printing with a Bluetooth connection. When printing, the printer is skipping labels. Printout is faded or weak. The battery charge is not lasting as long as it should. The test pages do not print. Possible Solution Check media settings. Make sure the label gap sensor is clean. For help, see Cleaning the PW50 on page 28. Check for errors in the software application. Make sure the label gap sensor and platen roller are clean. For help, see Cleaning the PW50 on page 28. Re-establish a Bluetooth connection with the mobile computer or scanner. For help, see Setting Up Bluetooth Communications on page 18, or see your mobile computer users manual. Make sure the mobile computer can print to a known good printer. Print a Bluetooth test print page to make sure that the mobile printer discovered your printer. For help, see Printing a Testprint on page 10. Make sure the printer is in Ready mode. Perform a testfeed by pressing and hold the Standby and Feed buttons until the PW50 beeps. Make sure the label gap sensor is clean. For help, see Cleaning the PW50 on page 28. Modify the Set Media Sensitivity command or the Set Dark Adjust command. For help, see the ESC-P Programmers Reference Manual (P/N 937-005-xxx). Check to see if the printhead needs cleaning. For help, see Cleaning the PW50 on page 28. Check the battery date. If the battery is a few years old, the shortened life may be due to normal aging. Replace the battery. Make sure that the blue light is not blinking. If it is, make sure your printer has media and that the media cover is closed. Make sure that you can advance media by pressing the Feed button. 26 PW50 Workboard Printer Users Guide Chapter 3 Troubleshooting and Maintaining the PW50 Printer Problems and Possible Solutions (continued) Problem Print quality is poor. Possible Solution Clean the printhead. For help, see Cleaning the PW50 on page 28. Check the battery and charge or replace as necessary. For help, see Charging the Batteries on page 6. Check the quality of the media. Use only Intermec media to ensure superior print quality and product performance. Check that the printer is configured to the appropritae Set Media Sensitivity value for the media you are using. Troubleshooting Communication Problems Use Dump mode to verify that the printer is receiving data from the host correctly. Is this true for the PW50?
PW50 Workboard Printer Users Guide 27 Chapter 3 Troubleshooting and Maintaining the PW50 Cold Booting the PW50 You rarely need to cold boot the PW50 printer, unless you are upgrading the firmware. If your printer occasionally locks up, you should cold boot it. A cold boot clears the working memory. Note: The Setup menu is not affected by a cold boot. Your printer retains all of your configuration settings after the printer powers back up. To reset the PW50 1 Disconnect the PW50 from power if externally powered. 2 Remove the battery from the PW50 for at least one second. 3 Insert the battery back into the PW50. 4 Reconnect external power if your PW50 is externally powered. Cleaning the PW50 To properly maintain your PW50, you should clean it at the recommended intervals. To avoid possible personal injury or damage to the printer, never insert any pointed or sharp objects into the printer. Use only the cleaning agents specified in this section. Intermec is not responsible for damage caused by any other cleaning materials used on this printer. Clean the printer with a cotton swab saturated with alcohol. 28 PW50 Workboard Printer Users Guide Chapter 3 Troubleshooting and Maintaining the PW50 Placeholder for illustration of PW50 parts to clean. PW50 Workboard Printer: Identifying the parts of the PW50 to clean regularly. Cleaning the PW50 Printer Printer Part Printhead Platen roller Paper sensors Tear bar Exterior Interior Cleaning Method Use 70% isopropyl alcohol on a cotton swab to clean the print elements from end to end. Rotate the platen roller and clean it thoroughly with 70%
isopropyl alcohol on a cotton swab. Clean thoroughly with 70%
isopropyl alcohol and a cotton swab. Clean thoroughly with 70%
isopropyl alcohol and a cotton swab. Clean with a water-dampened cloth. Brush or air blow. Make sure the paper sensor is free of dust. Cleaning Interval After every five rolls of media or more often if necessary. After every five rolls of media or more often if necessary. After every five rolls of media or more often if necessary. As needed. As needed. After every five rolls of media or more often if necessary. PW50 Workboard Printer Users Guide 29 Chapter 3 Troubleshooting and Maintaining the PW50 30 PW50 Workboard Printer Users Guide A Specifications 31 Appendix A Specifications Specifications Physical Dimensions Dimension Depth Height Width Weight Value Need this information. Need this information. Need this information. Need this information. Power Specifications Value Specification AC power adapter voltage 100 to 240V Printer voltage Operating power 100V to 240V and 50 Hz to 60 Hz Rechargeable 16.8 V 2200 mAh lithium-ion battery Temperature and Humidity Specifications Specification Operating temperature Storage temperature Charging temperature Relative humidity Sealing Value
-15C to 50C (5F to 122F)
-22C to 70C (-30F to 158F) 0C to 45C (32F to 113F) 0 to 95% non-condensing IP54 Memory Memory RAM Flash Value 16 MB 64 MB 32 PW50 Workboard Printer Users Guide Appendix A Specifications Print Speed and Resolution Specification Print speed Resolution Print Technology Value 4 ips (100 mm/s) 203 dpi (8 dots/mm) Technology Printhead Maximum print width Description Direct thermal 108 mm (4.25 in) Media Specifications Media Core inside diameter, standard Core inside diameter, with adapter Maximum roll outside diameter Media width, label with liner/receipt Media length, label Media length, receipt Media caliper, label with liner/receipt Media caliper, tag (maximum) Gap length (centered on perforation) Value 19 mm (0.75 in) 10.2 mm (0.4 in) 67.3 mm (2.65 in) 111.5 mm (4.4 in) 25.4 mm (1.0 in) to 609.6 mm (24 in) Continuous 0.05 mm (0.002 in) to 0.165 mm (0.0065 in) 0.15 mm (0.006 in) 3.17 mm (0.125 in) to 12.7 mm (0.50 in) 6.35 mm (0.25 in) 12.7 mm (0.50 in) 12.7 mm (0.50 in) Notch length (centered on perforation) Notch width (centered on perforation) Black mark length (centered on perforation) 3.17 mm (0.125 in) to PW50 Workboard Printer Users Guide 33 Appendix A Specifications Receipt roll stock media is supplied as a continuous roll. Label, tag, and fanfold media use repeat indicators for non-continuous media. Gap, notch, and black marks are used as repeat indicators:
Gap: Label and fanfold media Notch: Tag media Black mark: Label, tag, and fanfold media Here are a few things to keep in mind when ordering media for the PW50 printer:
Black marks can only be sensed on the back side of the media. You can use higher caliper media in the printer, but print quality will be reduced. Receipt roll stock media has an end of roll indicator. The end of roll indicator is a red marking (on last 3 feet of roll) on the thermally sensitive side of the paper. External Fanfold Media Specifications Specification Stack height:
Page length:
Value 70 mm (2.75 in) 152 mm (6 in) to 305 mm (12 in) Note: A 6-inch page length is supplied in 12-inch long stacks (two 6-
inch stacks of equal height with the bottom page linked). Specialty media is required for unique customer environments, including printer operating temperature extremes. Intermec recommends that you test the media in your application. Supported Media The PW50 printer supports direct thermal label, tag, and receipt media. Both North American and European label media are supported in multiple label lengths. Receipt media is supported in both a top coated and an uncoated paper in continuous roll stock only. The default media sensitivity number is: 180. 34 PW50 Workboard Printer Users Guide Appendix A Specifications Use the following table as a guide when setting sensitivity numbers. Recommended Media Sensitivity, Constant, Factor, and Print Speed Max Print Speed Duratherm Lightning Plus 4 ips 4 ips Duratherm Lightning 2 ips Duratherm Lightning Duratherm Synthetic 4 ips 4 ips Duratherm II Label 4 ips Duratherm III Label 4 ips Duratherm Near IR Duratherm 5 mil Tag 2 ips 40 40 40 40 40 40 40 40 60 52 48 100 80 80 80 50 Sensitivity Constant Factor Description North American Label Media 720 470 450 430 180 180 180 150 North America Receipt Media 401 102 101 European Label Media 440 140 40 40 40 45 32 30 30 40 47 70 Thermal Eco Thermal Top Duratherm TC Duratherm NTC - 2 Duratherm NTC 2 ips 2 ips 2 ips 2 ips 4 ips PW50 Workboard Printer Users Guide 35 Appendix A Specifications Accessories for the PW50 You can use these accessories (sold and ordered separately) with the PW50 printer. To order accessories, contact your local Intermec sales representative. AB13 Battery Use the lithium-ion 2200 mAh battery to provide power to the printer. AC18 4-Bay Battery Charger Use the AC18 to charge up to four batteries at a time. The battery charger is designed to sense when a battery is fully charged and not overcharge it, ensuring long and consistent battery life. PW50 Vehicle Dock (Model AV11) Use the vehicle dock to attach the PW50 to a truck. Power Supply (Model AE19) Provides power to the PW50 and the 4-bay battery charger (Model AC18). Power Supply (Model 073573) Provides power to the PW50 and the 4-bay battery charger (Model AC18). Serial Cable The serial adapter is an 8-pin DIN to DB9 connector that connects from the PW50 printer to your desktop PC. Handstrap Handstrap to conveniently carry your PW50 printer. Shoulder Strap Use the shoulder strap to easily carry the PW50 printer. The wide padded strap makes it comfortable to wear the printer for long periods of time. 36 PW50 Workboard Printer Users Guide IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual.
1 2 3 4 | Radio Info | Users Manual | 68.56 KiB |
Part No. 074821-001 Important BTS080 Information!
Contents For Users in the United States and Canada....................................................................... 2 For Users Outside of the United States and Canada............................................................. 3 Pour les utilisateurs en dehors du Canada et des Etat-unis.................................................... 5 Fr Benutzer auerhalb von Kanada und den Vereinigten Staaten................................................ 6 Per gli utenti al di fuori del Canada o degli Stati Uniti ......................................................... 6 Para Usuarios Fuera de Canada o de los Estados Unidos ...................................................... 7 Para Usurios Fora do Canad ou dos Estados Unidos ......................................................... 8 For Users in the United States and Canada Place this supplement in your manual. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired operation. Federal Communications Commission Compliance FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the radio or television receiving antenna. Connect the equipment to an outlet on a circuit different from that to which the radio or television Increase the separation between the computer equipment and receiver. receiver is connected. Consult the dealer or an experienced radio television technician for help. Operation Warning To comply with the FCCs RF exposure requirements and minimize health hazards:
The user shall not touch the antenna of this device when the device is in use. Caution Changes or modifications not expressly approved by Intermec could void the users authority to operate this equipment. Industry Canada Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This device requires a radio license unless it is used totally inside a building. (The user must obtain this license.) Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Cet appareil exige une license radio moins dtre entirement install dans un btiment. (Lutilisateur doit obtenir cette license.) 2 For Users Outside of the United States and Canada The Intermec product you purchased transmits and receives data using a 2.4 GHz Spread Spectrum system. Programming and configuration information for the transceivers is also provided in the host device documentation. Please check the Intermec Web site for additional documentation at www.intermec.com. Hereby, Intermec Technologies Corporation declares that this Model BTS080 is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product has been assessed to the following standards:
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (incl. Amdt. 1-4, 11) The original Declaration of Conformity is available on the Intermec Technologies Corporation Web site at www.intermec.com. This product transmits electromagnetic waves at 2.4 GHz frequency range. It has been tested and found compliant with CENELEC EN50360 and EN50361, 1999/519/EC, ACA Radiocommunications Standard 2003, U.S. (OET Guide 65), and Canadian (RSS 102) RF exposure regulations. The transmitter modules output power is 11.9 mW. The products using this module are intended for business and industrial environments. They should not be used in residential environments and by children. 0981 This product is marked with this logo and uses radio frequency bands that are not harmonized throughout the European Community. The following table indicates the areas of intended use of the equipment and any known restrictions. 3 Country of Intended Use Yes Austria Belgium Cyprus Czech Republic Denmark Estonia Finland France Germany Greece Hungary Ireland Italy Latvia Lithuania Luxembourg Malta The Netherlands Poland Portugal Slovakia Slovenia Spain Sweden United Kingdom Other non-EU:
Iceland Liechtenstein Norway Switzerland X X X X X X X X X X X X X X X X X X X X X X X X X X X X X License No Required Restrictions Details X Indoor use only Additional EMI/RFI Compliance This device meets the Class B limit requirements of CISPR 22. 4 Pour les utilisateurs en dehors du Canada et des Etat-unis Le produit Intermec que vous avez achet peut transmettre et recevoir des donnes laide dun systme dtalement du spectre de 2,4 GHz. Les informations de programmation et de configuration pour les metteurs-rcepteurs sont galement fournies dans la documentation de lappareil hte. Pour obtenir toute documentation supplmentaire, veuillez consulter le site Web dIntermec, ladresse www.intermec.com. Par la prsente, Intermec Technologies Corporation dclare que ce modle BTS080 est conforme aux exigences de base et autres exigences pertinentes de la Directive R&TTE (1999/5/EC). Ce produit a t valu par rapport aux normes suivantes :
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (comprenant lamendement 1-4, 11) La Dclaration de conformit originale est disponible sur le site Web dIntermec Technologies Corporation, ladresse www.intermec.com. Ce produit met des ondes lectromagntiques une plage de frquences de 2,4 GHz. Il a t valu et reconnu conforme aux rglements concernant lexposition la radiofrquence de CENELEC EN50360 et EN50361, de 1999/519/EC, de ACA Radiocommunications Standard 2003, des tats-Unis (OET Guide 65), et du Canada (RSS 102). La puissance de sortie du module metteur-rcepteur est de 11.9 mW. Les produits utilisant ce module sont destins des environnements commerciaux et industriels. Ils ne doivent pas tre utiliss dans des environnements rsidentiels et par des enfants. 0981 Ce produit est marqu de ce logo et il utilise des bandes de frquence radio qui ne sont pas harmonises sur le territoire de la Communaut europenne. Le tableau suivant rpertorie les zones dutilisation prvues pour lquipement et les restrictions connues. Pays dutilisation prvu Oui Licence requise Non Restrictions Dtails France X X Pour l'usage d'intrieur seulement. Conformit additionelle la norme EMI/RFI Cet appareil respecte les limites imposes pour la Classe B par le CISPR 22. 5 Fr Benutzer auerhalb von Kanada und den Vereinigten Staaten Das Intermec-Produkt, das Sie gekauft haben sendet und empfngt Daten mit Hilfe eines 2,4-GHz-
Spreizspektrumsystems. In der Dokumentation des Hostgertes finden Sie auerdem Informationen zum Programmieren und Konfiguriern der Sende-Empfangs-Gerte. Weitere Hinweise erhalten Sie auf der Intermec-Website unter www.intermec.com. Hiermit erklrt Intermec Technologies Corporation, dass das Modell BTS080 mit den wesentlichen Anforderungen und anderen sachdienlichen Vorschriften der R&TTE-Richtlinie (1999/5/EC) bereinstimmt. Dieses Produkt wurde gem der folgenden Normen bewertet:
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (einschl. Amdt. 1-4, 11) Die Originalkonformittserklrung steht auf der Website der Intermec Technologies Corporation unter www.intermec.com zur Verfgung. Dieses Produkt bermittelt elektromagnetische Wellen in einem Frequenzbereich von 2,4 GHz. Es wurde getestet und in bereinstimmung mit CENELEC EN50360 und EN50361, 1999/519/EC, ACA Radiocommunications Standard 2003, U.S. (OET Anleitung 65), und kanadischen (RSS 102) RF-
Bestrahlungsvorschriften befunden. Die Ausgangsleistung des Sende-Empfangs-Moduls betrgt 11.9 mW. Die Produkte, die dieses Modul verwenden, sind fr geschftliche und industrielle Umgebungen gedacht. Sie sollten nicht in Wohngegenden und in der Nhe von Kindern verwendet werden. 0981 Das Produkt ist mit diesem Markenzeichen versehen und verwendet Radiofrequenzbreiten, die in der Europischen Gemeinschaft nicht berall aufeinander abgestimmt sind. Zustzliche Elektromagnetische Strung-bereinstimmung Dieses Gert entspricht den Grenzbestimmungen der Klasse B von CISPR 22. Per gli utenti al di fuori del Canada o degli Stati Uniti Il prodotto Intermec che avete acquistato trasmette e riceve i dati tramite un sistema a 2,4 GHz che utilizza la tecnologia DSSS (spettro esteso). La documentazione del dispositivo host fornisce inoltre le informazioni sulla programmazione e la configurazione dei transceiver. Per altre informazioni, consultate il sito Web Intermec allindirizzo www.intermec.com. Con la presente Intermec Technologies Corporation dichiara che questo Modello BTS080 conforme ai requisiti essenziali e alle altre clausole importanti della direttiva R&TTE (1999/5/EC). Questo prodotto stato valutato in base ai seguenti standard:
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (incluso Amdt. 1-4, 11) 6 La dichiarazione di conformit originale disponibile presso il sito Web di Intermec Technologies Corporation a www.intermec.com. Questo prodotto trasmette onde elettromagnetiche con una frequenza intorno ai 2,4 GHz. Dai collaudi ai quali stato sottoposto risultato conforme alle norme CENELEC EN50360 e EN50361, 1999/519/EC, ACA Radiocommunications Standard 2003, statunitensi (OET Guide 65), e a quelle canadesi (RSS 102) relative allesposizione alle radiofrequenze. La potenza di uscita del modulo trasmittente di 11.9 mW. I prodotti che utilizzano questo modulo sono destinati ad ambienti industriali e commerciali e non debbono essere utilizzati in ambienti residenziali e dai bambini. 0981 Questo prodotto reca questo marchio ed utilizza bande di radiofrequnza che non sono armonizzate nellambito della Comunit Europea. Ulteriore conformit con EMI/RFI Questo dispositivo conforme ai limiti stabiliti in CISPR 22 per la Classe B. Para Usuarios Fuera de Canada o de los Estados Unidos Este producto de Intermec transmite y recibe datos por medio de un sistema de espectro ensanchado de 2,4 GHz. Para obtener informacin sobre la configuracin y programacin del transceptor, consulte la documentacin provista con el dispositivo host. Para obtener documentacin adicional, visite el sitio web de Intermec: www.intermec.com. Por la presente, Intermec Technologies Corporation declara que el Modelo BTS080 cumple con los requisitos esenciales de acuerdo con la directiva (1999/5/EC) de R&TTE. Este producto ha sido evaluado de acuerdo con los siguientes estndares o normas:
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (incl. Enmienda 1-4, 11) La Declaracin de Conformidad original est disponible en el sitio web de Intermec Technologies Corporation: www.intermec.com. Este producto transmite ondas electromagnticas de radio en la gama de frecuencias de 2,4 GHz. Ha sido probado y se ha determinado que cumple con las reglamentaciones del CENELEC EN50360 y EN50361, del 1999/519/EC, del ACA Radiocommunications Standard 2003, de los EE.UU. (OET Guide 65), y del Canad (RSS 102), referentes a la exposicin de RF. La potencia de salida del mdulo transmisor es de 11.9 mW. Los productos que usan este mdulo estn destinados para uso en ambientes comerciales e industriales. No deben ser usados en ambientes residenciales o en la proximidad de nios. 0981 Este producto est marcado con este logotipo y usa bandas de frecuencia de radio que no han sido armonizadas a lo largo de la Unin Europea. Conformidad adicional con EMI/RFI Este dispositivo cumple con los lmites requeridos para la Clase B de CISPR 22. 7 Para Usurios Fora do Canad ou dos Estados Unidos O produto Intermec que voc comprou transmite e recebe dados usando um sistema Espectro de Difuso de 2,4 GHz. As informaes sobre programao e configurao dos transceptores tambm so fornecidas na documentao do dispositivo hospedeiro. Consulte tambm o site da Intermec na web, no endereo www.intermec.com, para documentao complementar. Por este documento, a Intermec Technologies Corporation declara que o Modelo BTS080 atende aos requisitos essenciais e outras condies relevantes da Diretiva R&TTE (1999/5/EC). Esse produto foi avaliado em relao aos seguintes padres:
ETSI EN 300 328-2 v1.4.1 (2003-04) ETSI EN 301 489-17 v1.2.1 (2002-08) EN 60950:1992 (includa Amdt. 1-4, 11) A Declarao de Conformidade original est disponvel no site da web da Intermec Technologies Corporation no endereo www.intermec.com. Este produto transmite ondas eletromagnticas na faixa de freqncia de 2,4 GHz. Ele foi testado e aprovado quanto sua conformidade com os regulamentos de exposio RF do CENELEC EN50360 e EN50361, do 1999/519/EC, do ACA Radiocommunications Standard 2003, dos EUA (OET Guide 65), e do Canad (RSS 102). A potncia de sada do mdulo transmissor de 11.9 mW. Os produtos que usam este mdulo so destinados aos ambientes comerciais e industriais. Eles no devem ser utilizados em ambientes residenciais e por crianas. 0981 Este produto identificado por esta logomarca e utiliza bandas de freqncia de rdio que no esto harmonizadas na Comunidade Europia. Conformidades EMI/RFI Adicionais Este produto atende aos requisitos de limite Classe B do CISPR22. 6001 36th Avenue West Everett, WA 98203 U.S.A. www.intermec.com 2004 Intermec Technologies Corp. All Rights Reserved Important BTS080 Information!
*074821-001*
P/N 074821-001
1 2 3 4 | User Manual part 1 | Users Manual | 2.26 MiB |
6822 Series 80-Column Printer Users Manual 6822 Series 80-Column Printer Users Manual Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation. Information and specifications contained in this document are subject to change without prior noticed and do not represent a commitment on the part of Intermec Technologies Corporation. 2008 by Intermec Technologies Corporation. All rights reserved. The word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook, CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, i-gistics, INCA (under license), Intellitag, Intellitag Gen2, JANUS, LabelShop, MobileLAN, Picolink, Ready-to-Work, RoutePower, Sabre, ScanPlus, ShopScan, Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation. There are U.S. and foreign patents as well as U.S. and foreign patents pending. Wi-Fi is a registered certification mark of the Wi-Fi Alliance. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries. Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A. ii 6822 Series 80-Column Printer Users Manual Contents Contents Before You Begin . xii Safety Information . xii Global Services and Support. xiii Warranty Information. xiii Web Support. xiii Telephone Support . xiii Service Location Support . xiv Who Should Read This Document . xiv Related Documents . xiv Patent Information . xv 1 Using the Printer . 1 Learning About the Printer Models. 2 Guidelines for Operating the Printer . 3 Understanding the Control Panel . 3 Using the Reset Button . 4 Understanding the Power Supply Options . 6 Using the Internal Battery. 6 Connecting to a Vehicle Power Supply. 6 Connecting to a DC Power Source . 7 Fixed Mount Printer . 7 Portable Printer. 7 2 Installing the Printer . 9 Installing the Internal Battery . 10 Installing the Ribbon Cartridge. 11 Adjusting the Printhead Gap . 12 Loading the Paper Tray . 13 Loading Paper in the Printer . 13 Positioning the Paper . 13 Adjusting the Pinfeed Holders . 14 6822 Series 80-Column Printer Users Manual iii Contents Inserting a Computer in the Terminal Holder . 16 3 Maintaining the Printer . 19 Cleaning the Printer Case . 20 Cleaning the Outside of the Case . 20 Cleaning the Inside the Case. 21 Cleaning the Printer Ribbon . 21 Cleaning the Mask Spring. 22 4 Configuring the Printer . 25 Connecting to the Printer. 26 Understanding the Font Modules . 27 Using the Windows 95 or Windows 98 Printer Configuration Utility . 28 Installing the Configuration Files . 28 Generating Custom Configuration Files . 29 Understanding the Printer Configuration . 29 Selecting an International Font. 34 Selecting Parameters . 37 Saving Files to the Printer . 40 Default Printer Settings. 41 Using the Windows 2000 or Windows XP Printer Configuration Utility. 42 Installing the Windows 2000/XP Printer Configuration Utility . 42 Disabling the Microsoft ActiveSync Serial Port Connections . 46 Operating the Printer Configuration Utility . 46 Communicating with the Printer. 47 Setting the 6822 Configuration . 49 Default Printer Settings. 53 Error Messages . 54 Timeout Error . 54 Port Not Found Error . 54 Access Denied Error. 54 Connecting to the Bluetooth Adapter . 54 5 Control Code Definitions . 57 Understanding Control Code Definitions . 58 I/O Buffer . 58 iv 6822 Series 80-Column Printer Users Manual Contents Print Image Buffer . 58 Special Notations . 58 Using Printer Control Codes . 59 Backspace . 59 Beeper . 59 Cancel Line . 60 Carriage Return. 60 Delete . 60 Form Feed . 61 Select Half-Speed Printing . 61 Cancel Half-Speed Printing . 61 Set Inactivity Time for Sleep Mode . 61 Line Feed . 62 Perform Line Feed . 62 Perform n/216-inch Line Feed . 62 Perform n/216-inch Reverse Line Feed . 62 Perform Master Reset . 62 Set Print Position (absolute) . 63 Set Print Position (relative). 63 Select Top-Down Printing . 64 Select Bottom-Up Printing . 64 Select Unidirectional Printing . 64 Cancel Unidirectional Printing. 64 Select Unidirectional (one line) Printing . 65 Page Formatting Functions . 65 Set Page Length (lines). 65 Set Page Length (inches) . 66 Select 7/72-inch Line Spacing (7 dots) . 66 Select 1/6-inch Line Spacing . 66 Select n/216-inch Line Spacing . 67 Select n/72-inch Line Spacing (n dots) . 67 Set Right Margin . 67 Set Left Margin. 68 Set Skip Over Perforation. 68 Cancel Skip Over Perforation. 69 Character Style and Text Mode Functions . 69 Select Condensed Mode (compressed). 69 Cancel Condensed Mode . 70 Select Double-Strike Mode . 70 Cancel Double-Strike Mode. 70 Select Double-Wide Mode . 71 Cancel Double-Wide Print . 71 Select Double-Wide Mode . 71 Cancel Double-Wide Mode . 72 Select Elite Pitch. 72 6822 Series 80-Column Printer Users Manual v Contents Select Emphasized Print Mode. 72 Cancel Emphasized Print Mode . 73 Defining Intercharacter Space . 73 Select Italic Mode. 73 Cancel Italic Mode . 74 Master Select . 74 Select Pica Pitch . 75 Select Superscript Mode. 76 Select Subscript Mode . 76 Cancel Subscript/Superscript Mode . 76 Select Underline Mode. 77 Cancel Underline Mode . 77 Tabs and Tab Setting Functions . 77 Perform Horizontal Tab . 78 Set Horizontal Tabs . 78 Clear Horizontal Tabs. 79 Perform Vertical Tab . 79 Set Vertical Tabs . 79 Clear Vertical Tabs. 80 Set Vertical Tabs in Channel . 80 Clear Vertical Tabs in Channel . 80 Select Vertical Tab Channel. 81 Using Character Sets and User-Defined Functions . 81 Single-Byte Character Sets. 81 Double-Byte Character Sets . 82 Multi-Byte Character Sets . 82 Select National Character Set. 83 Hebrew Character Fonts. 84 User Defined Characters. 85 Copy ROM to RAM . 86 Define User-Defined Characters . 86 Select User-Defined Character Set. 87 Select Default Character Set. 87 Enable Printing of Codes 128-159 . 88 Disable Printing of Codes 128-159 . 88 Expand Printable Code Area . 88 Enable Printing of Character Graphics. 89 Disable Printing of Character Graphics . 90 Printing Character Graphics . 90 Graphics Functions . 91 Select Graphics Mode. 92 Reassign Graphics Mode . 92 Select Single Density Graphics Mode . 93 Select Low-Speed Double Density Graphics Mode. 93 Select High-Speed Double Density Graphics Mode . 93 Select Low-Speed Quadruple Density Graphics Mode . 94 Select 9-Pin Single Density Graphics Mode . 94 vi 6822 Series 80-Column Printer Users Manual Select 9-Pin Double Density Graphics Mode. 95 6 Troubleshooting . 97 Checking the Power Source . 98 Contents Aligning the Printer Mechanism . 98 Troubleshooting System Components. 100 Verifying the Printer Components . 100 Power Source Verification . 100 Communications / Host Computer Verification. 101 Understanding Printer Errors . 102 Runtime Errors . 102 Power-On-Self-Test (POST) Errors . 103 Fatal Errors . 104 Self-Test Function Descriptions . 105 Detailed Printer Self-Test . 106 Self-Test Report . 106 Understanding the Self-Test Report . 107 Miscellaneous Troubleshooting Tips . 111 Compatibility Issues . 114 Understanding Diagnostic Information. 114 Communications Pin-Out Configurations. 119 A Specifications . 125 Specifications . 126 Printer Dimensions . 127 Fixed Mount Printer . 127 Portable Printer . 128 Media Specifications. 128 Material Breakdown . 129 Caliper Breakdown . 130 Understanding the Fanfold Paper Page Layout. 131 B Bluetooth Configuration Commands and Specifications. 133 6822 Series 80-Column Printer Users Manual vii Contents Using Configuration Commands. 134 Operating Modes. 135 Command and Control Modes . 136 Set Local Bluetooth Device Name . 137 Set Class of Device/Service Field . 137 Set Service Name . 137 Connectable On/Off . 137 Specify Page Scan Timing . 138 Enable Discoverable. 138 Specify Inquiry Scan Timing . 138 Set Encryption/Authentication: PIN CODE . 139 Manage Security Modes. 139 Read Module Version. 140 Read Local Device Address . 140 Set Shutdown Timing. 141 Clear Link Key Table . 141 Understanding Adapter States or Modes. 141 700 Series or CK60 to 6822 Pass Through . 143 700 Series, CK60, or CN3 to Bluetooth Module Communication Interface 143 Power Management Flow Diagram. 144 Radio Power On/Off Mechanism . 145 Persistent Storage . 145 System Behavior/Software Considerations . 145 Remote Configuration. 146 Bluetooth Performance . 147 Diagnostics Capabilities . 147 Applications . 148 System Qualification. 149 Operation Resilience. 149 Environmental Specifications . 149 Safety/Regulatory/Agency Requirements. 150 Default Configuration . 152 C Cross-Reference Tables . 153 Control Codes and Escape Sequences. 154 Single Character Control Code Definitions . 170 viii 6822 Series 80-Column Printer Users Manual Contents Escape Sequence Quick Reference . 173 Factory-Installed Printer Defaults . 175 D Printer Font Test Jobs. 179 About the Printer Font Jobs. 180 Big 5 Traditional Chinese Character Set. 180 Simplified Chinese Character Set . 181 IBM 437 Code Page Character Set . 181 Japanese (Shift JIS) Character Set . 181 Korean Character Set . 182 International Character Set . 182 I Index . 183 6822 Series 80-Column Printer Users Manual ix Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions. This section explains how to identify and understand dangers, warnings, cautions, and notes that are in this document. You may also see icons which tell you when to follow ESD procedures. A warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury to the persons working on the equipment. A caution alerts you to an operating procedure, practice, condition, or statement that must be strictly observed to prevent equipment damage or destruction, or corruption or loss of data. This icon appears at the beginning of any procedure in this manual that could cause you to touch components (such as printed circuit boards) that are susceptible to damage from electrostatic discharge (ESD). When you see this icon, you must follow standard ESD guidelines to avoid damaging the equipment you are using. Note: Notes either provide extra information about a topic or contain special instructions for handling a particular condition or set of circumstances. x 6822 Series 80-Column Printer Users Manual Global Services and Support Before You Begin Warranty Information To understand the warranty for your Intermec product, visit the Intermec web site at www.intermec.com and click Service & Support > Warranty. Web Support Visit the Intermec web site at www.intermec.com to download our current manuals (in PDF). To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor. Visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support for your Intermec product. Telephone Support These services are available from Intermec. Services Order Intermec products Order Intermec media Order spare parts Technical Support Service Service contracts Description Place an order. Ask about an existing order. Order printer labels and ribbons. Order spare parts. Talk to technical support about your Intermec product. Get a return authorization number for authorized service center repair. Request an on-site repair technician. Renew a contract, ask about an existing contract. In the USA and Canada call 1-800-
755-5505 and choose this option 1 and then choose 2 1 and then choose 1 1 or 2 and then choose 4 2 and then choose 2 2 and then choose 1 1 or 2 and then choose 3 6822 Series 80-Column Printer Users Manual xi Before You Begin Outside the U.S.A. and Canada, contact your local Intermec representative. To search for your local representative, from the Intermec web site, click Contact. Service Location Support For the most current listing of service locations, click Support >
Returns and Repairs > Repair Locations. For technical support in South Korea, use the after service locations listed below:
AWOO Systems 102-1304 SK Ventium 522 Dangjung-dong Gunpo-si, Gyeonggi-do Korea, South 435-776 Contact: Mr. Sinbum Kang Telephone: +82-31-436-1191 Email: sbkang@awoo.co.kr Sammi Information Systems Co Ltd 7-9FL, Seo Jo Building 103-15, Galwor-Dong Seoul, Yong San-ku Korea, South 140-807 Contact: Kyung-Hee Koo Telephone: +82-2-790-5508 Email: jlovekoo@sammicomputer.co.kr Who Should Read This Document This users guide is for the person who is responsible for installing, configuring, and maintaining the 6822 printer. This users guide provides you with information about the features of the 6822 printer, and how to install, configure, operate, maintain, and troubleshoot them. Related Documents The Intermec web site contains Intermec documents (in PDF) that you can download for free. To download documents 1 Visit the Intermec web site at www.intermec.com. xii 6822 Series 80-Column Printer Users Manual Before You Begin 2 Click Support > Manuals. 3 In the Select a Product field, choose the product whose documentation you want to download. To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor. Patent Information This product is protected by one or more of the following United States patents:
5,581,293; 5,613,790; 5,927,876; 6,088,049; 6,345,920 There may be U.S. and Foreign Patents Pending. 6822 Series 80-Column Printer Users Manual xiii Before You Begin xiv 6822 Series 80-Column Printer Users Manual 1 Using the Printer Use this chapter to familiarize yourself with the 6822 printer. In this chapter you will find these sections:
Learning about the printer models Guidelines for operating the printer Understanding the control panel Understanding the power supply options 6822 Series 80-Column Printer Users Manual 1 Chapter 1 Using the Printer Learning About the Printer Models The 6822 printer is used in the route accounting industry to produce high-quality customer invoices, receipts, load reports, transfers, and other documents. A unique sleep feature saves energy when the printer is not printing, eliminating the need for an ON/OFF switch. Data input is normally provided by hand-held or mobile computers. The 6822 printer is available in the following models:
Fixed Mount Printer The fixed mount printer is mounted in motor vehicles or used in a settlement room. The terminal holder may be mounted on the printer or a remote dock can connect to the side of the printer. A deep paper tray, which holds up to 200 3-ply forms (up to 5 cm or 2 in of paper) is located under the printer mechanism. Portable Printer The portable printer has a handle so that you can carry it. An optional internal battery permits operation without the use of an external power source. The terminal holder is an integral part of this printer. A shallow paper tray, which holds up to 50 3-ply forms (up to 2.5 cm or 1.0 in of paper) is located under the printer mechanism. Note: The printer models are shown on page 8. The discharge of electrostatic energy accumulated on the human body, clothing, or other surfaces can damage or destroy the printhead or electronic components used in this printer. Avoid touching the electrical connectors while unpacking or setting up your printer. 2 6822 Series 80-Column Printer Users Manual Guidelines for Operating the Printer Chapter 1 Using the Printer Make sure that you mobile computer remains connected to the printer when printing or operating. Keep the printer cover closed except during maintenance or when loading paper. Make sure the paper is properly installed in the paper tray or dashboard mount. Disconnect the printer power cable when jump-starting the vehicle. Make sure your printer is loaded with paper before communicating with your mobile computer. Do not spill liquids or food crumbs into the printer. Do not use solvents or abrasive cleaners on the printer. Do not rest objects on, under, or against the printer. If the printer is attached to a vehicle electrical system, do not start or stop the vehicle engine while printing. Do not overload the paper tray or paper jams will occur. Understanding the Control Panel The printer control panel has four status indicators in the top row and three buttons in the bottom row. Three indicators blink when there is a problem. The three buttons adjust and align the paper. Understanding the Status Indicators Description Indicator Description Paper Out The printer is out of paper. Head Jam Low Battery The printhead is jammed and cannot move. The internal battery voltage, the vehicle battery voltage, or the power module voltage is too low. 6822 Series 80-Column Printer Users Manual 3 Chapter 1 Using the Printer Understanding the Status Indicators (continued) Description Indicator Description Power The power LED turns green when you press any button and goes off after ten seconds. The LED also goes on when:
the printer is attached to an external power supply the printer is using the internal battery and the battery charge is low a print job is sent to the printer you perform a power-on-self-test Understanding How to Use the 6822 Buttons Name Form Feed Button Set Page Line Feed FORM FEED SET PAGE LINE FEED Function Press this button to feed the paper into the printer mechanism or when the printer should advance to the next form. If the printer ran out of paper, press this button to initiate automatic paper loading. Press this button to signal the beginning of the page to the printer after you have made the appropriate paper adjustments;
or to set the line feed counter to zero and move the printhead to its home position. Press this button to clear a Paper Out error so printing can resume. Press this button to adjust the top of the paper to the next line. Note: All printer covers are hinged to the printer. These hinges have a tension screw (turn clockwise to tighten, turn counterclockwise to loosen), should you need to adjust them. Using the Reset Button Use the printer reset button to:
reset a printer that is unresponsive and apparently locked up 4 6822 Series 80-Column Printer Users Manual Chapter 1 Using the Printer force a synchronization between the printer and a connected PC when sending control codes restart the printer for any reason Note: The reset button does not reset a connected Bluetooth module as it is powered from a different power source. Both the fixed mount printer and the portable printer have a reset button on the left-hand side of the raised printer mechanism. See the following illustration for the location of the reset button. Reset button Fixed mount and portable printer reset button 6822 Series 80-Column Printer Users Manual 5 Chapter 1 Using the Printer Understanding the Power Supply Options The following power supply options are available for the 6822s. Using the Internal Battery The internal battery (P/N 317-075-001) allows the portable printer and some fixed mount printers to operate independently of other power sources. The 6822 discharges the internal battery even when the printer is not is use. Over time, the internal battery can discharge to the point where the battery is not recoverable. Plug the printer into an external charge source or disconnect the battery when you store the printer for any length of time. A total discharge of the battery is most likely to occur when the battery is new and the battery chemical reactions are not fully formed, or the battery has had only one charge cycle. Connecting to a Vehicle Power Supply You will need to order a printer installation kit to install the 6822 printer in a vehicle. The following kits are available:
P/N 203-242-101 (fixed mount printers) P/N 203-242-102 (portable printers). The installation kits contain all of the hardware (nuts, bolts, washers, a terminal ring, and a fuse link) for connecting the battery cable directly to the vehicle battery. These kits also contain adjustable wire clamps to secure the cable in place. Note: The 6820 printer and associated electrical wiring should be installed under the supervision of properly trained and qualified personnel. See the 6820 Printer Installation Instructions (P/N 931-052-001) to learn how to connect the printer to a vehicle power supply. 6 6822 Series 80-Column Printer Users Manual Connecting to a DC Power Source Chapter 1 Using the Printer Each printer has a dc power jack that connects the printer to a power source, such as the vehicle battery or an external power supply. Each printer communicates with a mobile computer through the mobile computer socket (in terminal holder, remote terminal holder, or vehicle dock). Fixed Mount Printer The dc power connector is on the bottom rear of the printer behind the printer terminal holder. The data communications socket is in either the printer terminal holder or a separate vehicle dock. Portable Printer The dc power connector is on the side of the printer beneath the printer terminal holder. The data communications socket is either in the printer terminal holder or a separate vehicle dock. 6822 Series 80-Column Printer Users Manual 7 Chapter 1 Using the Printer DC Power connector Mobile computer socket Fixed Mount Printer Mobile computer socket DC Power connector Portable Printer 6822 Printer Models 8 6822 Series 80-Column Printer Users Manual 2 Installing the Printer Installing the internal battery Installing the ribbon cartridge This chapter provides instructions how to set up the 6822 printer for the first time. In this chapter you will find these sections:
Adjusting the printhead gap Loading the paper tray Loading paper in the printer Inserting a computer in the terminal holder 6822 Series 80-Column Printer Users Manual 9 Chapter 2 Installing the Printer Installing the Internal Battery The optional internal battery is primarily for portable printers. The battery can go in some fixed mount printers using a cable and a factory-
installed adapter. The printer battery recharges automatically when the printer is connected to an external power source. For most installations, the external power source is passed through the printer to the mobile computer. The printer battery does not provide charge to the computer. Note: Remove the printer battery when storing a printer for more than 30 days. After storage, reinstall the battery and connect the printer to an external power source for at least 14 hours to recharge the battery. To install the internal battery 1 Unlatch and open the printer mechanism. 2 Lower the battery into the rear of the printer case, as shown. 3 Attach the battery cable to the battery. 4 Push the battery down and back under the back edge of the case. The battery should snap into place. 5 Close and latch the mechanism. Battery Battery cable Printer mechanism Installing the internal battery 10 6822 Series 80-Column Printer Users Manual Installing the Ribbon Cartridge Chapter 2 Installing the Printer Make sure there is a ribbon cartridge in the printer before you print and that the ribbon is fully seated (the cartridge makes a distinct snap or click when properly seated) with the visible portion of the ribbon straight and even. To install the ribbon cartridge 1 Turn the ribbon advance knob (in the direction of the raised arrows) to remove any slack in the ribbon. 2 Squeeze the ribbon cartridge locking tab into the cartridge, then lower the cartridge over the printhead. 3 Lower the tab side of the cartridge until it clicks. 4 Release the tab and press down on the arrow to fully seat the ribbon cartridge (tab clicks outward). 5 Turn the ribbon advance knob (follow raised arrows) to align the ribbon in the front of the printhead. Ribbon Locking tab Advance knob Tighten ribbon Installing the ribbon cartridge 6822 Series 80-Column Printer Users Manual 11 Chapter 2 Installing the Printer Adjusting the Printhead Gap The head gap adjuster is near the printer mechanism on the side opposite the green thumb wheel. The printhead adjuster has five notches between the printhead and the platen for different paper thicknesses. Verify the thickness of the paper loaded into the printer. To adjust the printhead gap If you are using single-sheet forms, set the head gap adjuster to the third notch away from the paper. If you are using multiple-sheet forms (2-ply or 3-ply), set the head gap adjuster to the fourth notch away from the paper. If you experience frequent head jams, set the head gap adjuster to the fifth notch away from the paper. This may stop the head jams. If the 2-ply and 3-ply paper have light printing, setting the gap adjuster to a closer setting will darken the print. 1 5 Adjusting the printhead 12 6822 Series 80-Column Printer Users Manual Loading the Paper Tray Chapter 2 Installing the Printer Note: Do not exceed the recommended amounts of paper quantity or thickness. When loading multiple-sheet paper, be sure to have the original faced up, with the leading edge towards the rear of the printer. To load the paper tray in fixed mount and portable printers 1 Unlatch and raise the printer mechanism. 2 Lower a stack of paper, with the original faced up, into the paper tray under the printer mechanism. The fixed mount printer holds up to 200 3-ply forms about 5 cm
(2 in) thick. The portable printer holds up to 50 3-ply forms about 2.5 cm (1 in) thick. 3 Pull the top form out and over the rear of the printer mechanism. Lower and latch the printer mechanism. To load paper from the flat paper tray 1 Hold a stack of paper, up to 6 cm (2.5 in) thick, with the original facing you, and lay the stack flat into the tray. 2 Pull the top form out to load into the printer. Loading Paper in the Printer Follow these steps to load the paper into the printer, or paper jams may occur. Positioning the Paper Paper for the 6822 has perforated strips that fit onto the pinfeed holder pins, guiding the paper into the printer. This paper is sold separately in 1, 2, or 3-ply forms. To position the paper 1 Open the pinfeed holders outward. 6822 Series 80-Column Printer Users Manual 13 Chapter 2 Installing the Printer 2 Take the top edge of the sheet of paper and position it, original side facing down, over the pinfeed holder pins. 3 Align the first few holes of the paper, on each side of the paper, onto the pinfeed holder pins. 4 Close the pinfeed holders. 5 Raise the paper bail. 1 3 4 2 5 Positioning the paper Adjusting the Pinfeed Holders Note: There are two pinfeed holders, one next to the green thumb wheel and one opposite the same wheel. Always loosen the pinfeed holder opposite the green thumb wheel. Note: Adjusting the pinfeed holder next to the green thumb wheel may cause information to print in the wrong place. If this pinfeed holder is moved, correct its location by releasing the pinfeed holder tab, moving the pinfeed holder as close to the green thumb wheel as possible, then locking the pinfeed holder tab, before adjusting the opposite pinfeed holder. To adjust the pinfeed holders 1 With the pinfeed holders open, release the locking tab on the pinfeed holder opposite the green thumb wheel. 14 6822 Series 80-Column Printer Users Manual Chapter 2 Installing the Printer 2 Adjust the pinfeed holder position so that the pins align with the paper. 3 Close the pinfeed holder. 4 Ensure that the paper is smooth (no folds, bulges, bows, etc.) between the pinfeed holders. If so, push the locking tab down on the pinfeed holder that you adjusted. Pinfeed holder Locked pinfeed holder locking tab Released pinfeed holder locking tab Thumbwheel
(green) Adjusting the pin feed holders To feed paper into the printer 1 Press Form Feed button to feed the paper into the printer. 2 Lower the paper bail. An empty printer autofeeds new paper approximately 0.25 cm (0.1 in) beyond the top of the paper bail. Note: The ideal distance to feed paper beyond the paper bail may vary due to environmental conditions (such as humidity) and specific aspects of certain paper. Use the green thumb wheel to position the paper to a desired distance according to your conditions. 6822 Series 80-Column Printer Users Manual 15 Chapter 2 Installing the Printer Note: If your paper has a preprinted logo on every page, make sure the printhead is below the preprinted logo. If not, you can adjust the position of the paper, either by pressing the Line Feed button, or by using the green thumb wheel. 3 Once the paper is properly positioned, press the Set Page button to clear the Paper Out light and indicate where the top of the page is. 4 Close the printer lid. Make sure the paper passes through the paper slot when the printer begins to print. Inserting a Computer in the Terminal Holder Note: When removing the computer, do not press the computer keys against the terminal slide retainer. Always store the computer in the terminal holder. The fixed mount or portable printers have terminal holder options for the 4000 Series, 61XX, 62XX, 600 Series, 700 Series, CK60, and the CN3 computers. To insert a 4000 series or a 62XX in the terminal holder 1 Insert the bottom of the computer into the terminal slide retainer. 2 Use the computer to push the terminal slide retainer and make room for the computer. 3 Lower the connector end of the computer into the terminal holder. 4 Slide the computer to fully seat it in the printer docking connector. To insert a 61XX, a 600 Series, a 700 Series, CK60, or a CN3 in a terminal holder 1 Insert the top of the computer into the terminal slide retainer. 2 Use the computer to push the terminal slide all the way in the direction shown. 3 Lower the connector end of the computer into the terminal holder. 16 6822 Series 80-Column Printer Users Manual 4 Slide the computer to fully seat it in the docking connector. Chapter 2 Installing the Printer Inserting a computer in a terminal holder 6822 Series 80-Column Printer Users Manual 17 Chapter 2 Installing the Printer 18 6822 Series 80-Column Printer Users Manual 3 Maintaining the Printer Use this chapter maintain your 6822 printer. In this chapter you will find these sections:
Cleaning the printer case Cleaning the printer ribbon Cleaning the mask spring 6822 Series 80-Column Printer Users Manual 19 Chapter 3 Maintaining the Printer Cleaning the Printer Case Periodic cleaning helps maintain the appearance and reliability of the printer. When cleaning the printer, inspect both the outside and the inside for signs of damage or wear. Glass cleaners containing ammonia will cause permanent damage to the printer cover. Do not use abrasives or solvents (acetone, ketone, toluene, or xylene) to clean any part of the printer or permanent damage to the printer will occur. Note: MICRO-CLEAN II is the only cleaner recommended for the printer case. Other cleaners can damage the printer case. Note: GUIDE SHAFT CLEANER is recommended for cleaning your 80-column printer guide shafts. Cleaning the printer guide shaft can reduce the number of head jams caused by dirt and buildup. Note: Both cleaners are sold separately. Cleaning the Outside of the Case Do not pour liquid cleaners directly on the printer case. Instead, dampen a soft, lint-free cloth with a quality cleaner and clean the exterior surfaces with this cloth. Do not use solvent solutions. Inspect the DC power jack, all cables, and the remote terminal holder or vehicle dock for damage. 20 6822 Series 80-Column Printer Users Manual Chapter 3 Maintaining the Printer Cleaning the Inside the Case Let the printer cool before you clean the inside of the printer or you may burn your fingers. Open the printer cover and inspect the ribbon cartridge and all visible moving parts on the printer mechanism for signs of wear or damage. Pinfeed holder Thumbwheel
(green) Paper bail Ribbon cartridge Moving parts in the printer mechanism Use a low-pressure, dry air source, such as canned air, or a vacuum, to remove accumulated paper dust from the printer mechanism. Head gap adjuster Cleaning the Printer Ribbon The printer ribbon contains a special lubricant to ensure that the fine dot wires inside the printhead receive adequate lubrication. Replace the ribbon frequently to prolong the life of the printhead. The printer requires no additional lubrication. To remove the ribbon cartridge 1 Move the printhead mechanism to an open area. 2 Squeeze the ribbon cartridge locking tabs (on the side of the cartridge) against the ribbon cartridge. 6822 Series 80-Column Printer Users Manual 21 Chapter 3 Maintaining the Printer 3 Lift the ribbon cartridge to remove the ribbon from the printhead. Make sure the ribbon does not catch or get sticky. 4 Lift the ribbon cartridge out of the printer. Cleaning the Mask Spring Check the mask spring behind the printhead.If the mask spring appears to be in good condition, install a new ribbon cartridge. If the mask spring is dirty, clean it as described below. To clean the mask spring 1 Unlatch the printhead locking tabs to release the printhead, lift the printhead aside, then lift up the paper bail. Do not detach the printhead unit. Never use a sharp object to clean between the printhead and the platen (rubber roller). This can damage the mask spring and printhead. 2 Remove the clear plastic paper guide that seats the mask spring, if necessary. Use your fingernails to loosen the base of the paper guide, then pull the paper guide straight up from the printer mechanism. 3 Remove the metal mask spring from the paper guide and clean with a quality cleaner. Replace if damaged. 4 Insert the mask spring in the paper guide and install the paper guide into the printer. 22 6822 Series 80-Column Printer Users Manual Chapter 3 Maintaining the Printer 5 Close the paper bail, reinsert the printhead, latch the two printhead locking tabs, and install the ribbon. Print head locking tabs Print head lifted aside Mask spring Cleaning the mask spring Raised paper bail 6822 Series 80-Column Printer Users Manual 23 Chapter 3 Maintaining the Printer 24 6822 Series 80-Column Printer Users Manual
1 2 3 4 | User Manual part 2 | Users Manual | 2.47 MiB |
6822 Series 80-Column Printer Users Manual 4 Configuring the Printer A Printer Configuration Utility is used to load font on the printer and to change the printer settings. In this chapter you will find these sections:
Connecting to the printer Understanding the font modules Using the Windows 95 or Windows 98 Printer Configuration Utility Using the Windows 2000 or Windows XP Printer Configuration Utility 25 Chapter 4 Configuring the Printer Connecting to the Printer Connect your printer to your desktop computer using a serial cable
(P/N 226-270-001). The serial COM port connector on either the fixed mount printer or portable printer is on your printer mechanism, the same side as the green thumb wheel. Before connecting to your PC, locate and disconnect the gray terminal holder ribbon cable connector from the floor of the printer cavity. The cable is located behind the printer mechanism on the same side as the green thumb wheel and is the one that is not attached to the printer mechanism. Disconnect this terminal holder ribbon cable from the floor of the printer cavity Ignore this cable attached to the printer mechanism Intermec provides printer configuration utilities for the following Windows operating systems. If your PC has either Windows 95 or Windows 98, go to page 27 for instructions. If your PC has Windows 2000 or Windows XP, go to page 42. Understanding the Font Modules Intermec provides the following font modules for your 6822:
nft00000.mod Default International, 4820 compatible nft00437.mod IBM/Microsoft compatible Code Page 437 nft00932.mod JIS Japanese nft00936.mod GB2312 Chinese Simplified nft00949.mod KSC5601 Korean 26 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer nft00950.mod Big 5 Traditional Chinese Note: There are three versions of the default font module
(nft0000.mod): Arabic, Turkish, and International. Any one version of this module, but not all three versions, can appear in the 6820 Printer Configuration Utility FONTS directory and install on the 6822. The International version of this font module is automatically placed in the FONTS directory when the Printer Configuration Utility is installed on the PC. All three versions are included on the printer toolkit CD:
The Arabic version is included in the Default Fonts\Arabic directory. The Turkish version is in the Default Fonts\Turkish directory. The International version is in the Default Fonts\International directory. Use the Printer Configuration Utility to replace the existing default font module (nft00000.mod) with any of the of the other provided fonts. The Printer Configuration Utility is provided in the 6820 Tool Kit. Instructions for installing fonts are provided later in this chapter. For Windows 95 and Windows 98 Users If the default installation process was followed, the Printer Configuration Utility FONTS directory is located at 6820PRTR\TOOLKIT\FONTS where 6820PRTR is replaced by the actual directory in which you chose to extract the files. For Windows 2000 and Windows XP Users If you followed the default installation process, the Printer Configuration Utility FONTS directory is located at Program Files\Intermec\6820 Printer Configuration Utility\FONTS. Do not rename the font files in the FONTS directory. If rename the fonts will not work correctly. Using the Windows 95 or Windows 98 Printer Configuration Utility 6822 Series 80-Column Printer Users Manual 27 Chapter 4 Configuring the Printer These instructions apply to desktop computers running either Windows 95 or Windows 98 operating systems. Installing the Configuration Files Configuration files for the 6822 are located in the toolkit CD
(P/N 215-270-001), these include the rpgpconf.exe Printer Configuration Utility program and the rpgpconf.ini initialization file. The Printer Configuration Utility uses the initialization file to specify the location and names of font and printer control program folders. To set up your PC 1 Extract the toolkit files from the nptk6822.exe self-extracting archive file. 2 Create a directory, on your PC, with an appropriate name for the Printer Configuration Utility files. You could choose to have the files extracted at the root directory of your PC or specify another folder. Execute the self-extracting file from the target directory while specifying the path to nptk6822.exe in the command line. When you run nptk6822.exe, a TOOLKIT folder is created, as well the following folders:
DOS FONTS PCFS 6820SYS Generating Custom Configuration Files The Printer Configuration Utility also helps you create custom configuration files. These files have a .pcf file extension, and stored in the folder specified in the initialization file. See the default .pcf file in the PCFS folder for an example configuration file. Understanding the Printer Configuration A configuration consists of a list of fonts, some parameter settings, and optionally, a printer control program. 28 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer When you start the Printer Configuration Utility, it creates a printer configuration. This configuration has no fonts, parameters are set to the default values, and there is no printer control program in memory. You can modify the basic printer configuration to meet your needs and load the custom configuration to your printer. Note: The working configuration is deleted when you exit the Printer Configuration Utility. To start the Printer Configuration Utility. 1 Run rpgconf.exe and click OK on the first screen to continue to the Main Menu. 6822 Series 80-Column Printer Users Manual 29 Chapter 4 Configuring the Printer 2 The following options are available on the Main Menu. Use Load Printer Configuration to load an existing configuration. Load either from a file or from the printer. Use Modify Printer Configuration to review or modify the working configuration, include the printer control program in the currently loaded configuration, or load fonts. Use Save Printer Configurations to save a configuration file to disk or download the working configuration to your 6822. Use Defaults to restore the printer to its default configuration. Note: When the Main Menu is first displayed, the Save Printer Configuration options are grayed out, prohibiting selection of those options until a configuration is loaded or modified. 3 Click Exit, then click Yes to exit the Printer Configuration Utility. Click No to the keep the Main Menu open. 30 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer To load configuration files from your PC 1 Click From File to access the File, Open window. 2 Select a configuration file to load, then click OK. If the selected file does not exist, a File does not exist! error message appears. Click OK to return to the Main Menu without loading a file. 3 If the file does exist, a warning message indicates that loading the selected file will overwrite your working configuration. Click OK to overwrite settings in working configuration, or Cancel to return to the Main Menu. 4 OK, the configuration from the selected file is loaded into memory and becomes the current working configuration. If this load is 6822 Series 80-Column Printer Users Manual 31 Chapter 4 Configuring the Printer successful, a message similar to the one shown below is displayed. Click OK to return to the Main Menu. 5 If the working configuration is not replaced successfully with the configuration from the selected file, an error message appears indicating that the operation failed. Click OK to return to the Main Menu without loading a file. To load a configuration from the 6822 1 Click From Printer from the Main Menu to display a warning message that indicates that the printers configuration will overwrite the working configuration. 2 Click OK to overwrite the configuration, otherwise click Cancel to return to the Main Menu without loading the printers configuration. 3 If you click OK, a message is then displayed prompting you to reset the printer. If the connection is not successful, after approximately 20 seconds, the following message appears. 32 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 4 Click Yes, to retry connecting to the printer. 5 If you click No, an error message appears and indicates that the configuration was not loaded. Click OK to return to the Main Menu. 6 If a connection is established, no further action is required The Printer Configuration Utility communicates with the 6822 to find out the current settings and which font modules are loaded. The name, version, and size of the font modules are displayed on the Get From Printer screen. 6822 Series 80-Column Printer Users Manual 33 Chapter 4 Configuring the Printer To modify a printer configuration Use this option to view or change a working configuration, including adding fonts from disk (on the PC), deleting printer fonts, and changing parameters settings. Select Modify Printer Configuration to view or modify the printer configuration. To include the control program Use this option to include the printer control program when saving the working configuration to the printer. The npfl6822.mod control program only needs to be changed when a new version becomes available. Select the Include Control Program check box to add the control program the next time you save the printer configuration. Selecting an International Font A variety of different international fonts are also available in the toolkit for the 6822. To select a font Click Fonts from the Main Menu to access the Font Selection screen where you can perform operations related to font files. The Fonts Available list shows font files that are available on disk. The Fonts Selected list show fonts that are in the current printer configuration. 34 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer Note: Save is grayed out, prohibiting that selection, until either new fonts are selected, or fonts are removed from the Fonts Selected list. To copy font files 1 Highlight the font files in the Fonts Available list. You can highlight several files at one time, using conventional Windows selection methods. Click Copy to copy those font files to the Fonts Selected list Note: If you attempt to copy fonts from the Fonts Available list when these fonts already exist in the Fonts Selected list, the following error message is displayed, once for each of the duplicate fonts (where the current font file name is listed in place of nft00000.mod). 6822 Series 80-Column Printer Users Manual 35 Chapter 4 Configuring the Printer 2 Click OK to close the error message and not copy the font to the Fonts Selected list. If there are two or more duplicate fonts, the cycle repeats until an error message is displayed for each of the duplicate font files. To delete font files Delete fonts from the Fonts Selected list to increase available memory in the printer. Select the font names you want to delete from the Fonts Selected list, then click Erase to clear those names. The Space Selection box, below the Fonts Selected list, displays the space remaining in flash (in kilobytes), based on fonts currently selected. When this number is negative, it means the available space in flash is less that the size of the selected fonts. Delete some fonts before saving the rest. Fonts marked with an asterisk (*), in the Fonts Selected list, are currently in printer memory. To cancel changes Click Cancel to return to the Main Menu without making any changes. If you have not made any changes to the Fonts Selected list, you return to the Main Menu. 36 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer Selecting Parameters To select a parameter Click Parameters from the Main Menu to access the Parameters window where you can modify any of the parameters that are not grayed out. Default parameter values are marked with an asterisk (*). To modify parameter configurations Select parameters on the screen using your stylus. Note: If you are using Bluetooth communication, you must change from the Norand Portable Communications Protocol (NPCP) mode to the Epson DTR mode with the baud rate set to 19.2 K and the parity set to None. To save parameters Click Save to update the working configuration and return to the Main Menu. To cancel the operation Click Cancel to return to the Main Menu without modifying any configuration parameters. 6822 Series 80-Column Printer Users Manual 37 Chapter 4 Configuring the Printer To save a printer configuration Click To File from the Main Menu to access the File Save As dialog. Specify the drive, directory, and filename for the printer configuration file. To specify a file name 1 Click the Alpha button, on either the File Open window or the File Save As window to open the keyboard onscreen for you to enter text. 2 Click Save to save the file name or click Cancel to exit without saving the text. The following confirmation message appears. 38 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 3 Click OK to return to the previous window without the entered text, or click Cancel to continue using the alpha keyboard. To save the configuration to disk After you have selected the drive, directory, and file name, click OK to save the configuration file. If a file by the same name exists, the following confirmation message is displayed, informing you that if you continue it will overwrite the existing file. Click Cancel to return to the Main Menu without saving the working configuration. Click OK fto continue. The following information is displayed assuring you that the working configuration was successfully saved to disk. Click OK to return to the Main Menu. To cancel the Save to File operation From the File, Save As window, click Cancel to abort the Save to File operation and return to the Main Menu without saving the working configuration. 6822 Series 80-Column Printer Users Manual 39 Chapter 4 Configuring the Printer Saving Files to the Printer Select the Save File to Printer option from the Main Menu, to send the working configuration to your 6822. When you select this option, the following warning message is displayed:
The message indicates the configuration will be copied into the 6822 flash memory and overwrite the current configuration. Click OK for the system to connect to the printer and transfer the configuration, or Cancel to return to the Main Menu without updating the printer. Connecting to the printer 1 After you click OK, a message appears informing you that the system is attempting to establish connection with the printer. 2 Connect a serial cable (P/N 226-270-001) between your PC and the printer. 3 Press the Reset button to reset the printer. 4 If the connection is not successful after approximately 20 seconds, the following message is appears. 5 Click Yes to retry making a connection to the printer. 40 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 6 If the configuration was not saved to the printer, the following error message appears. If the connection is successful, the following screen appears and the printer configuration is updated. The screen also displays the data transfer status. Default Printer Settings The following are the default settings used when you click Restore Defaults to Printer:
Default Printer Settings Settings Zero Print Option Autofeed Configuration Protocol Values Slash all zeros (zeros are printed with a slash) CR (carriage return at end of line without line feed) NPCP 6822 Series 80-Column Printer Users Manual 41 Chapter 4 Configuring the Printer Default Printer Settings Settings Parity Bit Rate Values N/A (for NPCP) 19.2 K For other printer defaults, see Factory-Installed Printer Defaults on page 175. Using the Windows 2000 or Windows XP Printer Configuration Utility These instructions apply to desktop computers running either Windows 2000 or Windows XP operating systems. Installing the Windows 2000/XP Printer Configuration Utility The Windows 2000/XP Printer Configuration Utility is provided on the 6822TKCD toolkit CD (P/N 235-145-001). To set up your PC to use the Printer Configuration Utility 1 Insert the toolkit CD in your PC. 2 From your desktop, use your Explorer application to view the contents of the toolkit CD. 42 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 3 Double-click the setup.exe executable file, then click Next from the Welcome screen to continue. 4 The printer configuration utility files are copied to the Program Files\Intermec\6822 Printer Configuration Utility folder. To install the files in a different folder, enter the path and folder name. 6822 Series 80-Column Printer Users Manual 43 Chapter 4 Configuring the Printer You can also specify if everyone who uses the computer has access to the printer configuration files or limit access to yourself. 5 Click Disk Cost to see the amount of disk space required to install the Printer Configuration Utility. Click OK to close and return to the installation screens. 44 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 6 Click Next to verify installation, click Back to adjust the information on the previous screen, or click Cancel to exit the installation. 7 Installation Complete appears on the screen. Click Close to exit the installation program. 6822 Series 80-Column Printer Users Manual 45 Chapter 4 Configuring the Printer Disabling the Microsoft ActiveSync Serial Port Connections If you use Microsoft ActiveSync to connect to your computers, you need to disable the serial port connections before using the Printer Configuration Utility. To disable ActiveSync 1 In the ActiveSync application on your desktop, select File >
Connection Settings. 2 Clear Allow USB connections and Allow connections to one of the following. 3 Click OK. 4 Close the ActiveSync application. Operating the Printer Configuration Utility The Printer Configuration Utility consists of a list of fonts, some parameter settings, and a printer control program. When the Printer Configuration Utility is active, it holds a configuration clipboard in memory. Initially, this configuration has parameters set to their default values. Consider the contents of the configuration clipboard as temporary and lost when you exit from the utility. Click the Get 6820 Configuration button to view the current printer configuration. 46 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer Click the Set 6820 Configuration button to change printer setting and send those settings to the printer. Click the Reset to Defaults button to reset the to the factory default printer configuration. To start the Printer Configuration Utility Click Start > Programs > Intermec > 6820 Printer Configuration Utility > PConfigApp.exe to start the Printer Configuration Utility. Communicating with the Printer You can use COM port 1, 2, or 3 to communicate with your printer. COM port 1 is the default selection, but if it is not available or is being used by another application, select another COM port. To communicate with the printer 1 Click either the Get 6820 Configuration or the Set 6820 Configuration button to open communications with the printer. The Opening COM Port x to printer . message appears in the text box when you initiate communications sith the printer. The x in the message indicates which COM port is being used. 6822 Series 80-Column Printer Users Manual 47 Chapter 4 Configuring the Printer 2 When the Press Reset on the printer message appears in the text box, press the Reset button on your printer. For the location of the Reset button on your printer, see Using the Reset Button on page 4 3 The Opening COM Port x to printer. Done. message indicates that communication between your PC and the printer has been established. Note: If Unable to open COM Port x to printer appears in the text box another software application may be using the selected COM port. Select another COM port or disable the software application using the COM port. See page 54 for more error messages. 48 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer To view the settings on your 6822 1 Click the Get 6820 Configuration button to initiate communication. 2 The Getting printer parameters . message appears when the Printer Configuration Utility retrieves configuration information from the printer. 3 The message Getting printer parameters . Done appears after configuration information is retrieved. 4 Modify configuration settings or click OK to close the Printer Configuration Utility. Setting the 6822 Configuration To modify configuration settings 1 Make changes to the Configuration Clipboard or click the Reset to Defaults button to undo your selections and return them to their defaults. Note: When using a Bluetooth adapter you must select the DTR communications protocol and a bit rate of 19.2K. 2 Click the Set 6820 Configuration button to initiate communication with the printer. The Setting printer parameters . message appears when you initiate communication with the printer. 6822 Series 80-Column Printer Users Manual 49 Chapter 4 Configuring the Printer 3 The Setting printer parameters . Done message appears when configuration parameters are set. Note: The Unable to set printer parameters message indicates a dropped connection between your PC and your printer. 4 Click OK to close the utility and detach the serial cable. To update 6822 fonts or the 6822 control program Click the Fonts and Control button to update the fonts stored in your printer or to update the printer control program. The Fonts Available for Update list shows font files that are available. The Fonts Selected for Update list show fonts that are to be installed jon the printer. 50 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer To learn what fonts are currently installed on your printer Click the Get Printer Fonts button. The installed fonts appear in the text box in the bottom right corner of the dialog. To select font files Highlight the font files you want to download in the Fonts Available for Update list. Click the right arrow pointing to the Fonts Selected for Update list to copy the selected font files to this list. Below is a sample screen. 6822 Series 80-Column Printer Users Manual 51 Chapter 4 Configuring the Printer If the fonts you select exceed the space available in printer memory, an error message appears. Click OK to close the error message and not copy the font to the Fonts Selected for Update list. If there are two or more fonts that exceed the space allowed, this message repeats until an error message is displayed for each of the font files that went over the space allowed. The Space Needed information shown beneath the Fonts Available for Update list indicates the total space required (in bytes) for all of the fonts in the list. The Space Remaining information listed below the Fonts Selected for Update list displays the space remaining in the printer, given the fonts in the Selected list. Click Update Printer to update the printer fonts and the control program depending on the options selected on the dialog. If the Selected list is empty and the Include control program update is not checked, a Nothing selected for update message appears in the text box. Formats the printer flash for font updates and writes new font files to the printer for any fonts in the Selected list. Click the top, right arrow to copy selected font files from the Fonts Available for Update list to the Fonts Selected for Update list. Click the bottom, left arrow to remove any selected files from the Fonts Selected for Update list. Click Update Printer to update the fonts in the printer with those in the Fonts Selected for Update list. The Update progress: bar indicates the progress as the control program or fonts are written to the printer. 52 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer Check the Include program control update check box to include the printer control program when updating the printer. Note: You only need to update the control program when new versions of the control program are released. Default Printer Settings. Default Printer Settings Settings Zero Print Option Autofeed Configuration CR (carriage return at end of line without Value Print zeros without a slash Protocol Parity Bit Rate line feed) NPCP N/A (for NPCP) 19.2 K (19200) For other printer defaults, see Factory-Installed Printer Defaults on page 175. 6822 Series 80-Column Printer Users Manual 53 Chapter 4 Configuring the Printer Error Messages There are three instances when the 6822 may not connect to your PC. In the example error messages, an x indicates the assigned COM port number. Timeout Error The timeout error may occur due to either of these situations:
The printer was not reset in the time allowed. The COM port exists on the desktop computer but nothing is connected to the port. Error Message Unable to open COM port x to printer. Printer not reset within the time allowed or printer not connected to COM port x. Port Not Found Error The COM port does not exist. The particular COM port is identified in the error message. Error Message Unable to open COM port x to printer. COM port x cannot be found. Access Denied Error The COM port exists but a connection with the 6822 is not established. The particular COM port is identified in the error message. Error Message Unable to open COM port x to printer. Access to COM port x is denied. Close applications using COM port x or try another port. Connecting to the Bluetooth Adapter If your 6822 has a Bluetooth adapter, be sure to connect this adapter after you finish reconfiguring the 6822 fonts and exit the Printer Configuration Utility (gray cable beneath the printer mechanism). To enable Microsoft ActiveSync serial port based connections 1 Start ActiveSync and select File > Connection Settings. 54 6822 Series 80-Column Printer Users Manual Chapter 4 Configuring the Printer 2 Check Allow USB connections and Allow connections to one of the following. 3 Click OK. 4 Close the ActiveSync application. 6822 Series 80-Column Printer Users Manual 55 Chapter 4 Configuring the Printer 56 6822 Series 80-Column Printer Users Manual 5 Control Code Definitions This chapter contains a set of control code definitions and specifications for page layout for the 6822 printer. In this chapter you will find these sections:
Understanding control code definitions Using printer control codes Understanding the fanfold paper page layout 6822 Series 80-Column Printer Users Manual 57 Chapter 5 Control Code Definitions Understanding Control Code Definitions I/O Buffer All characters and control codes received by the printer are stored in this buffer. Characters and controls codes are read from this buffer and acted upon to form the print buffer. Characters are removed from the I/O buffer as they are processed. Print Image Buffer All characters go through this buffer on their way to the printed page. This buffer contains the graphic image of the dots to print, from which characters are rendered. It is cleared when its contents are printed. Special Notations The following information defines notations included in the format definitions of the escape sequences, throughout this section. Special Notations Notation
(0)
(1)
NUL Description Used in the ASCII column of any of the Format definitions, indicates that its value can only be zero (and not the character 0). For example: Select Top-
Down Printing ESC US (0). Used in the ASCII column of any of the Format definitions, indicates that its value can only be one (and not the character 1). For example: Select Bottom-Up Printing ESC US (1). When a number (at the end of an escape sequence) is marked with an asterisk, then either the value corresponding to that number or the value of the string character can be used for that number. For example, if 1* is shown, then either the value (1), or the value of the string character
(decimal: 49, hex: 31) can be used. The NUL character is represented in the Dec column as 0, in the Hex column as 00, and in the ASCII column as NUL. 58 6822 Series 80-Column Printer Users Manual Using Printer Control Codes Chapter 5 Control Code Definitions These control code definitions are organized by categories of functions. The following methods assist in locating control codes easily:
Alphabetically organized (complete list)refer to the Control Codes and Escape Sequences table on page 164. Locate the index for the control code, and turn directly to that page. Numeric order (single character codes only)refer to the Single Character Control Code Definitions table on page 180. Locate the index for the control code, and turn directly to that page. Numeric order (complete list)refer to the Escape Sequence Quick Reference table on page 183 and look up control codes by their actual code values. Locate the index for the escape sequence, and turn directly to that page. The print buffer is emptied. The printhead is moved to the left one character space (using the current pitch). This can be performed to, but not beyond, the left margin setting. The backspace is ignored if justification of right, full, or centered is selected. Decimal 8 Hex 08 ASCII BS The backspace control code (BS) is not reliable when text contains different character pitches. For reliable backspacing, use the escape sequence (ESC \), Set Relative Print Position. The printer produces a beep lasting approximately 1/10 of a second Decimal 7 Hex 07 ASCII BEL Backspace Format Beeper Format 6822 Series 80-Column Printer Users Manual 59 Chapter 5 Control Code Definitions Cancel Line All of the characters currently in the print buffer are discarded. Current print position is set to left margin. Text already printed cannot be canceled Format Decimal 24 Hex 18 ASCII CAN Carriage Return Repositions the printhead at the start of the print line (usually at the left margin), and repositions the pointer to the start of the print buffer, after printing all data in the buffer. Also, all of the one line functions are reset, such as bold, double-strike, double-wide, or unidirectional printing. Decimal 13 Hex 0D ASCII CR Note: You can add an automatic line feed with a configuration item. Deletes the last character in the print buffer. This functions only in left justification. Decimal 127 Hex 7F ASCII DEL Format Delete Format 60 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Prints the contents of the print buffer, clears the print buffer, and advances the paper to the top of the next page (Top of Form), according to the current page length setting. The carriage position is moved to the start of the line Form Feed Format Decimal 12 Hex 0C ASCII FF Select Half-Speed Printing Turns on half-speed mode to provide quiet printing, and more accurate print positioning during text mode printing. Format Decimal 27 115 1*
Hex 1B 73 01*
ASCII ESC s 1*
Cancel Half-Speed Printing Turns off half-speed mode (factory default), and continues with normal speed printing. Format Decimal 27 115 0*
Hex 1B 73 00*
ASCII ESC s 0*
Set Inactivity Time for Sleep Mode Sets the amount of time the printer waits before it goes into low-power mode. The factory default is 10 seconds. Format Decimal 27 122 n Hex 1B 7A n ASCII ESC z n 6822 Series 80-Column Printer Users Manual 61 Chapter 5 Control Code Definitions Line Feed Perform Line Feed Prints and then clears the contents of the print buffer, resets the character count to zero; and advances the printhead to the next print line, using the current spacing. The position of the carriage is not affected and a carriage return is not executed. Decimal 10 Hex 0A ASCII LF Perform n/216-inch Line Feed Advances the paper to n/216 of an inch. This does not affect subsequent line feeds. Range of n is 0-255. Decimal 27 74 n Hex 1B 4A n ASCII ESC J n Perform n/216-inch Reverse Line Feed Reverses the line feed by n/216 of an inch. This does not affect subsequent line feeds. Range of n is 0-255. Decimal 27 106 n Hex 1B 6A n ASCII ESC j n Format Format Format Perform Master Reset Initializes the printer and restores factory installed printer defaults, (see Factory-Installed Printer Defaults on page 175 for a complete list of settings that are initialized with this command). Format 62 Decimal 27 64 Hex 1B 40 ASCII ESC @
6822 Series 80-Column Printer Users Manual Set Print Position (absolute) Chapter 5 Control Code Definitions Moves the printhead to an absolute horizontal position on the paper. The distance is specified in dots from the left margin to the new print position
(at which subsequent characters are printed). Each dot represents 1/60 of an inch. The values for n1 and n2 determine the distance, as follows:
number of dots = n1 + (n2 * 256) Maximum position is 480. The previous contents of the current print buffer is printed. If the position specified moves the printhead outside the current margins, the command is ignored and the previous setting remains in effect. This command is also ignored in right, center, and full justification modes. Format Decimal 27 36 n1 n2 Hex 1B 24 n1 n2 ASCII ESC $ n1 n2 Set Print Position (relative) Moves the printhead to a horizontal position on the paper, relative to the current printhead position. The distance specified is in dots. To determine n1 and n2, first calculate the displacement required in 1/120ths of an inch. If the displacement is to the left, subtract it from 65536. The values for n1 and n2 determine the distance, as follows:
number of dots = n1 + (n2 * 256) Maximum displacement is 960. If the position specified would place the printhead outside the current margins, this function is ignored and the previous setting remains in effect. This function is also ignored in right, center, and full justification modes. Format Decimal 27 92 n1 n2 Hex 1B 5C n1 n2 ASCII ESC \ n1 n2 6822 Series 80-Column Printer Users Manual 63 Chapter 5 Control Code Definitions Select Top-Down Printing Enables top-down printing (factory default). First page is printed first. Format Format Format Format Decimal 27 31 0 Hex 1B 1F 00 ASCII ESC US (0) Select Bottom-Up Printing Enables bottom-up printing. The last page is printed first. Decimal 27 31 1 Hex 1B 1F 01 ASCII ESC US (1) Select Unidirectional Printing Turns on unidirectional printing mode. Unidirectional printing moves the printhead from left-to-right only, allowing for more accurate print positioning during text mode printing. Decimal 27 85 1*
Hex 1B 55 01*
ASCII ESC U 1*
Cancel Unidirectional Printing Turns off unidirectional printing (factory default), allowing the printhead to print in both directions Decimal 27 85 0*
Hex 1B 55 00) ASCII ESC U 0*
64 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Select Unidirectional (one line) Printing Turns on unidirectional printing for the current line only. The contents of the print buffer is printed, and cleared before setting this mode. This allows more accurate print positioning during text mode printing, for the current line. Format Decimal 27 60 Hex 1B 3C ASCII ESC <
Page Formatting Functions This set of functions consists of control codes that change the formatting of the page. The page length (form length) and margin settings define the printable area on the page. These settings need to conform to the actual size of the paper used in the printer. The line spacing functions set the amount of space from one line to the next, for line feeds. The factory default is 1/6 inch (6 lines per inch). The page length, vertical tab, and skip over perforation functions are also dependent on the line spacing function. Set Page Length (lines) Sets the length of the paper in lines, where the range of n (number of lines) is 1-127 (default = 66). Keep in mind the line spacing and actual length of the paper when specifying this value, since this function is dependent on those parameters. Top-of-Form is reset to the current line and the Skip Over Perforation setting is canceled. Format Decimal 27 67 n Hex 1B 43 n ASCII ESC C n 6822 Series 80-Column Printer Users Manual 65 Chapter 5 Control Code Definitions Set Page Length (inches) Sets thee length of the paper in inches, where the range of n (number of inches) is 1-22 (default = 11). Keep in mind the line spacing and actual length of the paper when specifying this value, since this function is dependent on those parameters. Top-of-Form is reset to the current line and the Skip Over Perforation setting is canceled. Decimal 27 67 0 n Hex 1B 43 00 n ASCII ESC C NUL n Select 1/8-inch Line Spacing Sets the line spacing is set to 1/8 of an inch (8 lines per inch), for subsequent lines. Decimal 27 48 Hex 1B 30 ASCII ESC 0 Select 7/72-inch Line Spacing (7 dots) Sets the line spacing to 7/72 of an inch (approximately 9.7 lines per inch), for subsequent lines. Decimal 27 49 Hex 1B 31 ASCII ESC 1 Select 1/6-inch Line Spacing Sets the line spacing to 1/6 of an inch (6 lines per inch), for subsequent lines (factory default). 1/6 inch is equal to 12 dot spacing. Decimal 27 50 Hex 1B 32 ASCII ESC 2 Format Format Format Format 66 6822 Series 80-Column Printer Users Manual Format Format Chapter 5 Control Code Definitions Select n/216-inch Line Spacing Sets the line spacing to n/216 of an inch, for subsequent lines. A spacing of 1/216 inch is 1/3 the distance between pins of the printhead
(approximately 1/3 of a dot) and 27/216 is 8 lines per inch. Range of n is 0-255. Decimal 27 51 n Hex 1B 33 n ASCII ESC 33 n Select n/72-inch Line Spacing (n dots) Sets the line spacing to n/72 of an inch, for subsequent lines. A spacing of 1/72 inch (1 point in font size) is the distance between pins on the printhead (approximately 1 dot) and 9/72 is 8 lines per inch. Range of n is 0-85. Decimal 27 59 n Hex 1B 41 n ASCII ESC A n Set Right Margin Clears all text in the print buffer and sets the right margin to n columns, using the current character pitch. This is the number of the characters from column 1 (at the left edge of the paper) to the last column before the right margin (factory default = 80). Minimum space between margins is the width of one double-width pica character. Maximum value for this is the maximum number of characters
(based on the current pitch) that would fit between the left margin and the right edge of the default printable area of the page. Ranges shown below could vary, depending on values of other parameters that affect character width. If the value specified is not within the allowed range, it is ignored. 6822 Series 80-Column Printer Users Manual 67 Chapter 5 Control Code Definitions Range of n is 2-80 in Pica mode, 2-96 in Elite mode, and 2-136 in Compressed mode. Decimal 27 81 n Hex 1B 51 n ASCII ESC Q n Set Left Margin Clears the print buffer text and sets the left margin, relative to the number of columns to the left of the first column to print
(factory default = 0). Minimum space between margins is the width of one double-width pica character. Maximum value must be less than the right margin. Ranges shown below could vary, pending on other parameter values that affect character width. If the specified value is not within the range, it is ignored. Range of n is 0-78 in Pica mode; 0-93 in Elite mode, and 0-133 in Compressed mode. Decimal 27 108 n Hex 1B 6C n ASCII ESC l n Set Skip Over Perforation Defines the number of lines to skip between the last printed line on the page and the first printed line on the next page is set. If the value specified for this function is greater than the page length, it is ignored. This function is canceled by using one of the Set Page Length functions
(factory default = disabled). This function is valid for continuous paper only. The amount of space left blank at the bottom of the printed page is dependent upon the current Line Spacing. Decimal 27 78 n Hex 1B 4E n ASCII ESC N n 6822 Series 80-Column Printer Users Manual Format Format Format 68 Chapter 5 Control Code Definitions Cancel Skip Over Perforation Cancels the skip over perforation, which allows the maximum number of lines to print on each page. Format Decimal 27 79 Hex 1B 4F ASCII ESC O Character Style and Text Mode Functions The following set of functions affect the appearance of text on the printed page. This could involve size, typeface, or other characteristics of the text. Select Condensed Mode (compressed) Selects condensed mode which prints characters at approximately 60%
of the normal width. This results in character pitches, as shown below
(for exact pitch values, see Master Select on page 74). Character Pitches Condensed Mode 17 cpi (approximate) Condensed + Expanded 9 cpi (approximate) Condensed + Elite 20 cpi (approximate) This function empties the print buffer and turns compressed mode on, and stays on until canceled by Cancel Compressed Mode, ESC SI or DC2 (factory default = disabled). Note: This function is not supported in Double-Byte Character Sets (DBCS). Format Decimal 27 15 15 Hex 1B 0F 0F ASCII ESC SI SI 6822 Series 80-Column Printer Users Manual 69 Chapter 5 Control Code Definitions Cancel Condensed Mode Cancels the compressed mode, enabled by Select Compressed Mode, SI or ESC SI (1). Note: This function is not supported in DBCS. Format Format Format Decimal 27 18 18 Hex 1B 12 12 ASCII DC2 DC2 Select Double-Strike Mode Enables double-strike printing, until Cancel Double-Strike Mode is encountered. Factory default disables double-strike. Text is made bolder by printing each dot twice, with the second dot slightly below the first dot. This mode is not available in NLQ, but is not canceled when you select NLQ. Note: This function is not supported in DBCS. Decimal 27 71 Hex 1B 47 ASCII ESC G Cancel Double-Strike Mode Cancels Double-Strike Mode. Note: This function is not supported in DBCS. Decimal 27 72 Hex 1B 48 ASCII ESC H 70 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Select Double-Wide Mode Enables expanded print for the current line only. The mode set previously returns on subsequent lines. However, expanded print can be canceled with Cancel Expanded Print, DC4 or ESC W (0), before end of current line, or wrapping of the print buffer. This works with all three pitches (Pica, Elite, Compressed). This mode is also terminated by the execution of a Carriage Return, Line Feed, Form Feed, Vertical Tab or wrapping of the print buffer. Note: This function is not supported in DBCS. Decimal 27 14 14 Hex 1B 0E 0E ASCII ESC SO SO Cancel Double-Wide Print Cancels expanded print for the current line only. Modes set previously return on subsequent lines. However, it does not cancel expanded mode set by Select Double-Wide (expanded) Mode, ESC W (1) or Master Select, ESC !. Note: This function is not supported in DBCS. Decimal 27 20 20 Hex 1B 14 14 ASCII DC4 DC4 Select Double-Wide Mode Enables expanded print until Cancel Expanded Print is encountered. Factory default disables double-wide mode. Note: This function is not supported in DBCS. Format Format 6822 Series 80-Column Printer Users Manual 71 Chapter 5 Control Code Definitions Format Decimal 27 87 1*
Hex 1B 57 01*
ASCII ESC W 1*
Cancel Double-Wide Mode Cancels Double-Wide Print mode. Note: This function is not supported in DBCS. Format Format Decimal 27 87 0*
Hex 1B 57 00*
ASCII ESC W 0 Select Elite Pitch A character pitch of 12 cpi (characters per inch) is selected. This also cancels Pica Pitch (factory default = Pica). Note: This function is not supported in DBCS. Decimal 27 77 Hex 1B 4D ASCII ESC M Select Emphasized Print Mode Enables Emphasized Print mode until Cancel Emphasized Mode is encountered. The text is made bolder by printing each dot twice, with the second dot slightly to the right of the first dot. Factory default disables Emphasized mode. Note: This function is not supported in DBCS. 72 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Decimal 27 69 Hex 1B 4B ASCII ESC E Cancel Emphasized Print Mode Cancels Emphasized Pring mode. Note: This function is not supported in DBCS. Format Format Decimal 27 70 Hex 1B 46 ASCII ESC F Defining Intercharacter Space Format Format Defines the amount of space to the right of each character, in addition to the space allowed in the character design. The variable n represents the number of units of space, with each unit equal to 1/120 of an inch. Range of values for n is 0-63 with a factory default of 0. Decimal 27 32 n Hex 1B 20 n ASCII ESC SP n Select Italic Mode The text (nongraphic) characters are italicized. Factory default disables Italic mode. Note: This function does not work well with DBCS or alternate Single Byte Character Sets (SBCS). Decimal 27 52 Hex 1B 34 ASCII ESC 4 6822 Series 80-Column Printer Users Manual 73 Chapter 5 Control Code Definitions Cancel Italic Mode Cancels the Italic mode. Note: This function does not work well with DBCS or alternate Single Byte Character Sets (SBCS). Format Format Decimal 27 53 Hex 1B 35 ASCII ESC 5 Master Select Allows you to specify a combination of print modes. The variable n is determined by combining values for the desired modes, by adding them together. Note: This function is not supported in DBCS. Decimal 27 33 n Hex 1B 21 n ASCII ESC ! n Valid combinations of the values in the following table include any combinations except that Pica cannot combine with Elite. Example Pica Compressed Italic Underlined, by adding values (00h + 04h + 40h +
80h), which results in C4h for the value of n. Master Select Values Hex Value 00h 01h 04h 08h 10h 20h Mode Pica Elite Condensed (compressed) Emphasized Double-Strike Double-Width (expanded) 74 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Master Select Values (continued) Hex Value 40h 80h Mode Italic Underlined The following print conflicts occur between modes. A mode in any column takes precedence over all modes in the columns to its right. 1 Elite 2 Emphasized 3 Compressed The following print modes can be combined producing different pitches:
Print Conflicts Print Modes Pitch 5 cpi 6 cpi 8.58 cpi 10 cpi 12 cpi 17.16 cpi Mode Expanded Expanded Elite Expanded Compressed Pica Elite Compressed Select Pica Pitch Selecta a character pitch of 10 cpi (characters per inch) (factory default). This also cancels Elite pitch. Note: This function is not supported in DBCS. Format Decimal 27 60 Hex 1B 50 ASCII ESC P 6822 Series 80-Column Printer Users Manual 75 Chapter 5 Control Code Definitions Select Superscript Mode Prints all subsequent characters in approximately 2/3 the normal height in the upper part of the character space, until Cancel Subscript/
Superscript is encountered. Note: This function is not supported in DBCS. Format Format Format Decimal 27 83 0*
Hex 1B 53 00*
ASCII ESC S 0*
Select Subscript Mode Prints all subsequent characters in approximately 2/3 the normal height in the lower part of the character space, until Cancel Subscript/
Superscript is encountered. Note: This function is not supported in DBCS. Decimal 27 83 1*
Hex 1B 53 01*
ASCII ESC S 1*
Cancel Subscript/Superscript Mode Cancels the effects produced by Select Superscript Mode and Select Subscript Mode. Factory default also disables both of these modes. Note: This function is not supported in DBCS. Decimal 27 84 Hex 1B 54 ASCII ESC T 76 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Select Underline Mode Enables the underlining of all subsequent characters (including spaces) until the Cancel Underline mode function is encountered. Decimal 27 45 1*
Hex 1B 2D 01*
ASCII ESC 1*
Cancel Underline Mode Cancels the effect of the Select Underline mode. Factory default also disables the Underline mode. Format Format Decimal 27 45 0*
Hex 1B 2D 00*
ASCII ESC 0*
Tabs and Tab Setting Functions There are control codes for setting horizontal and vertical tabs. Horizontal tabs:
Are not affected by subsequent changes in pitch. May range up to maximum width for character and printer size. All previous tab stops are cleared when new tab stops are set. If the left margin is changed after the horizontal tabs are set, tab stops are cleared. Become absolute positions and are not affected by any subsequent change in character size. Set outside of the printable area are ignored. Vertical tabs:
Tab positions are line numbers, counting from the Top of Form. All tabs set beyond the page length are stored, but are not used. Any tab set within the SOP range (Skip Over Perforation), during the time SOP is active, are stored but not used until SOP is canceled. 6822 Series 80-Column Printer Users Manual 77 Chapter 5 Control Code Definitions If a vertical tab, and the next tab stop is outside the printable page area, a form feed is executed placing the printhead at the next Top of Form. Previous tab stops are cleared when new tab stops are set. Are not affected by subsequent changes in line spacing. Perform Horizontal Tab Moves the print position to the next horizontal tab stop. The tab positions, set by ESC D, the Set Horizontal Tabs function, are not affected by any changes in character pitch. The factory default tab settings are at intervals of eight characters, in the currently selected pitch. For the default tabs, the actual distance to each tab position is affected by changes in character pitch. Decimal 9 Hex 09 ASCII HT Set Horizontal Tabs Resets the current horizontal tabs, and new horizontal tabs are set up, based on the current character width (pitch). Format Format Decimal 27 68 n1 n2 ..nk 0 1B 44 n1 n2 .. nk 00 ESC D n1 n2 .. nk NUL ASCII Hex n1 is the first tab (range for tab stops: 1-160), n2 is the second tab (all tabs in ascending order), ... are subsequent tabs (maximum tabs: 32), nk is the last tab to set (any value less than the previous tab value acts as a terminating character), NUL is the terminating character. 78 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Clear Horizontal Tabs Clears all horizontal tab stops. It is merely a variant behavior of the Set Horizontal Tabs function, where the NUL acts as an early terminating character, as existing tabs normally clear before setting any new tabs. Decimal 27 68 0 Hex 1B 44 00 ASCII ESC D NUL Perform Vertical Tab Prints the contents of the current print buffer, and then moves the print position to the next vertical tab stop. If no channel is selected, then channel 0 is used. The carriage position is changed to the start of the next print line. If the vertical tab is performed beyond the last tab position set or beyond the last line of a form, then a form feed is performed. If no vertical tabs are defined, then the paper advances one line, using the currently selected line spacing, without changing the carriage position. Decimal 11 Hex 0B ASCII VT Set Vertical Tabs Resets the current tabs, and vertical tabs are set up, based on the current line spacing. Tab settings are not affected by subsequent changes in line spacing. Format Format Format Decimal 27 66 n1 n2 .. nk 0 1B 42 n1 n2 .. nk 00 ESC B n1 n2 .. nk NUL ASCII Hex n1 is the first tab (range of values for tab stops: 1-255), n2 is the second tab (all tabs must be in ascending order), ... are subsequent tabs
(maximum number of tabs: 16), nk is the last tab to set (any value less than the previous tab value acts as a terminating character), NUL is the terminating character. All tab settings with this function are stored in channel 0. 6822 Series 80-Column Printer Users Manual 79 Chapter 5 Control Code Definitions Format Format Format Clear Vertical Tabs Clears all vertical tab stops . This is a variant behavior of the Set Vertical Tabs function, where the NUL acts as an early terminating character. Decimal 27 66 0 Hex 1B 42 00 ASCII ESC B NUL Set Vertical Tabs in Channel This function works the same as the Set Vertical Tabs function, except that it stores the tabs into a specified channel, as specified by the variable c. This channel is selected for use by the Select Vertical Tab Channel function. Decimal 27 98 c n1 n2 .. nk 0 1B 62 c n1 n2 .. nk 00 ESC b c n1 n2 .. nk NUL ASCII Hex c is the channel number (range: 0-7), n1 is the first tab (range of values for tab stops: 1-255), n2 is the second tab (all tabs must be in ascending order), ... are subsequent tabs (maximum number of tabs: 16), nk is the last tab to set (any value less than the previous tab value acts as a terminating character), and NUL is the terminating character. Clear Vertical Tabs in Channel Clears all vertical tab stops in the specified channel. This is merely a variant behavior of the Set Vertical Tabs in Channel function, where the NUL acts as an early terminating character, since this function normally clears the existing tabs before setting any new tabs. Decimal 27 98 c 0 Hex 1B 62 c 00 ASCII ESC b c NUL 80 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions Select Vertical Tab Channel Selects a specified vertical tab channel. It sets up the current tabs from that channel. Once this function is performed, all subsequent Perform Vertical Tab commands use the tab stops from the list retrieved from the specified channel. At power on, the printer uses the tabs stored in channel 0. Format Decimal 27 47 c Hex 1B 2F c ASCII ESC / c c is the channel number (range: 0-7). Using Character Sets and User-Defined Functions You can install different character sets on the printer. In some cases more than one character set may be present at one time, depending on the amount of available font memory. The 6822 reserves 438K of memory for installing fonts in flash memory. You can install fonts using NPCP or the Printer Configuration Utility. Single-Byte Character Sets Single-byte character sets (SBCS) are supported for MS-DOS, PL/N, and Intermec application compatibility. Nft00000.mod is the default character set (font) for compatibility with the 6822 80-Column Printer. Nft00437.mod is the IBM/Microsoft compatible character set for code page 437. 6822 Series 80-Column Printer Users Manual 81 Chapter 5 Control Code Definitions Double-Byte Character Sets Double-byte character (DBCS) sets require two bytes to send to the printer to define the character to print. The first byte of the character code sent to the printer is known as a lead-in byte. The second byte of the character code is known as the trailing byte. Different character sets have different requirements for the values of both lead-in and trailing byte. When the lead-in byte does not fall in the range listed for the character set, a character from a SBCS may print. The following double-
byte character sets are supported by the 6822. Double Byte Character Sets Code Page 936 Font Module nft00936.mod nft00950.mod nft00932.mod nft00949.mod 950 932 949 DBCS Languages GB 2312 Chinese
(simplified) big 5 Traditional Chinese Shift JIS Japanese KSC 5601 Korean Lead-in Byte A1hABh B0hF7h A1hC6h C9hF9h 81h9Fh E0hFCh A1hACh B0hC8h CAhFDh Trailing Byte A1hFEh 40hFEh (except 7Fh) 40hFCh (except 7Fh) A1hFEh Multi-Byte Character Sets Double-byte character sets and single-byte character sets can mix when printing a report. This mixture is referred to as a Multi-Byte Character Set (MBCS). When a DBCS is selected, the characters from the SBCS code page currently selected are used for rendering character codes and control codes from 0 to 127. Codes above 127 (that fall within the range of lead-in bytes for the selected character set) treat the byte that follows as a trailing byte for that character set. Otherwise, for character codes above 128, the character code from the selected SBCS is printed. NFT00950.MOD (BIG 5 DBCS) does not allow the MBCS mode. For this character set, only control codes from 0-31 are treated as single byte characters when they are not proceeded by a lead-in byte. All escape sequence character strings are treated as SBCS. 82 6822 Series 80-Column Printer Users Manual Format Chapter 5 Control Code Definitions Select National Character Set By default, code page 0 is selected by the printer at reset. Use the following escape sequence to select international character support. Escape sequence codes can only be used for code page 0. All other code pages use direct character code mapping to select the appropriate font for rendering. Decimal 27 82 n Hex 1B 52 n ASCII ESC R n n is 0-14 and is the country code, as shown in the International Character Sets table on the next page. The default value for n is zero (USA). A full 256 character set is not provided for these sets. There are 64 international characters stored in ROM, 32 in Roman and 32 in Italic. They are stored as codes 0-31 and 128-255. These are normally not accessible. The ESC R command makes these codes available, but only 12 characters at a time. These 12 are available in these positions of the ASCII character table: 35, 36, 64, 91, 92, 93, 94, 96, 123, 124, 125, and 126, as shown in the International Character Sets table. International Character Sets Country USA France Germany England (UK) Denmark 1 Sweden Italy Spain 1 Japan Norway Denmark 2 Spain 2 Latin America Country Number 0 1 2 3 4 5 6 7 8 9 10 11 12 35
P
64 92 93
94 36 91
96
123 124 125 126
b
6822 Series 80-Column Printer Users Manual 83 Chapter 5 Control Code Definitions International Character Sets (continued) Country Hebrew Greek Country Number 13 14 96 94 91 64 36 92 93 35 123 124 125 126 Hebrew fonts are available in the supplied font files. See Hebrew Character Fonts below. Greek fonts are available in the supplied font files. See the Greek Character Sets on page 85. Hebrew Character Fonts Hebrew characters represented by decimal values 38 and 65 through 90 are represented by the following 7x7 font descriptions. 70 69 68 67 66 72 71
*.*.*.* ..*...* .....*. *....*. .....* ...*... *....*. *....*. ...... ...... ...... ...... ...... ...... ...... *.*.*.. ...... ...... ...... ...... ...... ...... ...... ...... 65
....... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... 73
....... ...... .....* ....... .....* ....... *...... ...... ...... ...... ...... ...... ...... ...... ...... ...... 81 80 75 74 77 78 79 85 88 83 84 82 86 76 87 84 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions
....... ...... ...... ...... ...... ...... 89 90 91 Greek Character Sets Chr Dec A 97 B 98 99 G D 100 E 101 102 Z H 103 104 q Hex 61 62 63 64 65 66 67 68 Dec 105 106 107 108 109 110 111 112 Hex 69 6a 6b 6c 6d 6e 6f 70 Chr I K L M N X O P Dec 113 114 115 116 117 118 119 120 Hex 71 72 73 74 75 76 77 78 Chr P S T Y F X Y W The selected set stays in effect until the printer is reset and receives a Master Reset command, or a new international character set is selected. Note: This function is only used with the default character set. User Defined Characters This code addresses user-defined characters and selection into memory. Note: RAM-based definition or redefinition of standard characters is only useful when the default SBCS code page is selected. There is no method to redefine characters in the other code pages, since unique code pages can be created and loaded into the printer memory. 6822 Series 80-Column Printer Users Manual 85 Chapter 5 Control Code Definitions Copy ROM to RAM The characters in ROM are copied into RAM, so a complete user-defined character set is created by editing selected characters. This ensures that all characters are defined when a user-defined character set is selected. This eliminates the need to cancel the selection when printing defined characters. Note: This function is only useful with the default SBCS. Format Format Decimal 27 58 0 0 0 Hex 1B 3A 00 00 00 ASCII ESC . NUL NUL NUL Define User-Defined Characters Characters are redefined by the user in the currently selected mode. However, they can only be used in draft mode. Note: This function is only useful with the default SBCS. Decimal 27 38 0 k1 k2 s1 d1 ... d11 Hex 1B 26 00 k1 k2 s1 d1 ... d11 ASCII ESC & k1 k2 s1 d1.....d11 k1 is the character code of the first character to redefine, k2 is the character code of the last character to redefine (any character between 0-255 can be redefined), and (k1 could equal k2, if only one character is defined). For each character defined, you must supply 12 bytes of data. Bits 0-3 represent the end position in the grid Bits 4-6 represent the start position in the grid Bit 7 determines whether the character uses the top eight pins or the bottom eight pins of the printhead. If bit 7 = 0, the top eight pins are s1 is the first byte that describes the character format 86 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions used. If bit 7 = 1, the bottom eight pins are used. The start and end positions are ignored during character imaging, but must be accurate to redefine the character code. d1...d11 is the data that comprises the dot image pattern of the defined character. When printable code expansion is enabled with ESC I, the Printable Code Area Expansion function, and the user-defined character set is selected with ESC % (1), the Select User-Defined Set function, then the codes (less than 20h and greater than 7Fh) can be defined for use and are printable. When printable code expansion is enabled with the Enable Printing of Codes 128-159 function, and the user-defined character set is selected with the Select User-Defined Set function, then codes (between 80h and 9Fh) can be defined for use and are printable. For a list of these characters, refer to the Printable Code Expansion Characters on page 89 Select User-Defined Character Set A user-defined character set can be selected, after the Define User-Defined Characters function is used to define the character set. Note: This function is only useful with the default SBCS. Decimal 27 37 1 Hex 1B 25 01 ASCII ESC % (1) Select Default Character Set If the Select User-Defined Set function was previously set, this function switches back to the default character set. Note: This function is only useful with the default SBCS. Format Format Decimal 27 37 0 Hex 1B 25 00 ASCII ESC % (0) 6822 Series 80-Column Printer Users Manual 87 Chapter 5 Control Code Definitions Format Format Enable Printing of Codes 128-159 All codes (128-159) are treated as printable characters, rather than control codes, with this function. This allows the use of these characters for user-defined characters. A user-defined set must be selected, using the Select User-Defined Set function, before these characters can print. Factory default disables printing of these codes.. Note: This function can only be used when the default SBCS is selected. Decimal 27 54 Hex 1B 36 ASCII ESC 6 Disable Printing of Codes 128-159 Disables the printing of codes 128-159. By default, these codes are disabled. Decimal 27 55 Hex 1B 37 ASCII ESC 7 Expand Printable Code Area This function allows certain ASCII codes (00h to 1Fh) and codes (80h to 9Fh) to print when the variable n is set to the value of 1. This allows the use of these codes for user-defined characters. If n = 0, the function returns these two ranges of characters to non-printable control codes. A user-defined character set must be selected by ESC % (1), the Enable Printing of Codes 128-159 function, before these codes can print. In both ranges, only the following codes can redefine as printable characters. Codes not listed, within the range (00h-1Fh), print as standard control codes. Codes not listed, within the range (80h-9Fh), are converted to a control code in the range of (00h-1Fh), by subtraction of 80h. Note: This function is only useful with the default SBCS. 88 6822 Series 80-Column Printer Users Manual Format Decimal 27 73 n Hex 1B 49 n ASCII ESC I n Chapter 5 Control Code Definitions Printable Code Expansion Characters ASCII Hex DC1 00 NAK 01 02 SYN ETB 03 FS 04 GS 05 06 RS US 10 ASCII NUL SOH STX ETX EOT ENQ ACK DLE Hex 11 15 16 17 1C 1D 1E 1F Hex 80 81 82 83 84 85 86 90 ASCII none none none none none none none none Hex 91 95 96 97 9C 9D 9E 9F ASCII none none none none none none none none Format Enable Printing of Character Graphics Enables the printing of character graphics, until disabled with the Disable Printing of Character Graphics function. Note: This function is only useful with the default SBCS. Decimal 27 116 1 Hex 1B 74 01 ASCII ESC t (1) For character values from 0 to 31 (00h-1Fh):
When the default SBCS code page is selected, the FX-86e IBM character graphics symbol set is printed. When other SBCS code pages are selected, the codes (00h-1Fh), listed above in the Printable Code Expansion Characters table are printed. For character values from 32 to 126 (20h-7Eh):
6822 Series 80-Column Printer Users Manual 89 Chapter 5 Control Code Definitions When the default SBCS code page is selected, the selected international character set is printed. When other SBCS code pages are selected, the international character set selection is not in effect. For the character value 127 (7Fh):
When the default SBCS code page is selected, a space is printed When other SBCS code pages are selected, the character associated with the code page is printed. For character values from 128 to 255 (80h-FFh), the FX-86e Epson Character Graphics set is printed. Disable Printing of Character Graphics Disables the printing of character graphics. Factory default disables this function. Decimal 27 116 0 Hex 1B 74 00 ASCII ESC t (0) Printing Character Graphics This function allows printing of character graphics from the currently selected SBCS code page, by sending a graphics string to the printer. The values of the graphics data bytes can range between 0-255. Decimal 27 43 n d1 ... dn Hex 1B 2B n d1 ... dn ASCII ESC + n d1 ... dn n is the length of the character graphic string and d1 ... dn are the character graphics data stream. The number of data bytes must be equal to the value of the variable n. The range of values (for the characters in each graphics data byte):
0-255. For character values from 0 to 31 (00h-1Fh):
Format Format 90 6822 Series 80-Column Printer Users Manual Chapter 5 Control Code Definitions When the default SBCS code page is selected, the FX-86e IBM character graphics symbol set is printed. When other SBCS code pages are selected, currently selected single byte code page character graphics are printed. For character values from 32 to 126 (20h-7Eh):
When the default SBCS code page is selected, the selected international character set is printed. When other SBCS code pages are selected, the character from the currently selected code page are printed. For the character value 127 (7Fh):
When the default SBCS code page is selected, a space is printed When other SBCS code pages are selected, the character graphics symbol is printed. For character values from 128 to 255 (80h-FFh):
When the default SBCS code page is selected, the FX-86e Epson Character Graphics set is printed. When other SBCS code pages are selected, the corresponding character is printed. Graphics Functions Eight-Pin Graphics Modes All 8-pin graphics functions require parameters, n1 and n2, which represent the length of the graphics string that follows the Select Graphics Mode command, and are calculated as follows (assuming a temporary variable n):
The simplest calculation, is to divide n (total number of dots needed for the graphics string) by 256. Then n2 is the quotient (the whole number) and n1 is the remainder. If you require less than 256 dots (columns), then n1 indicates the number of dots and n2 is set to zero. n = total number of graphics dots needed for the graphic string n2 = integer of (n divided by 256) n1 = remainder of the n2 calculation 6822 Series 80-Column Printer Users Manual 91 Chapter 5 Control Code Definitions Format Format Select Graphics Mode Enables the Graphics moderepresented by the variable m in the Graphic Modes table. The total number of dot columns to print is represented by n1 and n2. Any graphic string that exceeds the length of the print line is discarded. Decimal 27 42 m n1 n2 Hex 1B 2A m n1 n2 ASCII ESC * m n1 n2 Reassign Graphics Mode Changes Graphic modes. Decimal 27 63 s n Hex 1B 3F s n ASCII ESC ? s n s is one of the K, I, Y, or Z characters and n is one of the 0-7 modes as shown in Graphic Modes table. Graphic Modes Mode Single-density Low Speed Doubledensity
*High Speed Double-density
*Low-Speed Quadruple-density CRT I SingleDensity Plotter CRT II
*Double-Density Plotter
*Adjacent dots in a given row cannot be printed in these modes. m Dots per Inch / Dots per 8 in Line 0 1 2 3 4 5 6 7 60 dots per inch, 480 dots per 8 in line 120 dots per inch, 960 dots per 8 in line 120 dots per inch, 920 dots per 8 in line 240 dots per inch, 1920 dots per 8 in line 60 dots per inch, 480 dots per 8 in line 72 dots per inch, 576 dots per 8 in line 90 dots per inch, 720 dots per 8 in line 144 dots per inch, 1152 dots per 8 in line 92 6822 Series 80-Column Printer Users Manual Format Format Format Chapter 5 Control Code Definitions Select Single Density Graphics Mode This is a simple method of printing graphics. The resolution is 60 dots per inch. Each 8 in line can accommodate 480 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. Calculating the parameters, n1 and n2, is described on page 94. Decimal 27 75 n1 n2 Hex 1B 4B n1 n2 ASCII ESC K n1 n2 Select Low-Speed Double Density Graphics Mode If Single Density graphics does not produce high enough density, try this mode. The number of dots per inch is doubled. However, the speed is reduced to half of what it would be with single density. Calculating the parameters, n1 and n2, is described on page 94. This is 8-pin single density graphics. The resolution is now 120 dots per inch. Each 8-inch line can accommodate 960 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. Decimal 27 76 n1 n2 Hex 1B 4C n1 n2 ASCII ESC L n1 n2 Select High-Speed Double Density Graphics Mode This 8-pin graphics mode produces the same density as the Low-Speed Double Density mode, however, the speed is doubled. Calculating the parameters, n1 and n2, is described on page 94. Decimal 27 89 n1 n2 Hex 1B 59 n1 n2 ASCII ESC Y n1 n2 The resolution is still 120 dots per inch. Each 8-in line can accommodate 960 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. Make sure adjacent dots in a given dot row are not printed. 6822 Series 80-Column Printer Users Manual 93 Chapter 5 Control Code Definitions Select Low-Speed Quadruple Density Graphics Mode With this 8-pin graphics mode, the number of dots per inch has gone up to 4x what it was in single density. Calculating the parameters, n1 and n2, is described on page 94. Decimal 27 90 n1 n2 Hex 1B 5A n1 n2 ASCII ESC Z n1 n2 The resolution is now 240 dots per inch. Each 8-in line can accommodate 1920 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. Make sure adjacent dots in a given dot row are not printed. Nine-Pin Graphics Modes These 9-pin graphics functions also require two parameters, n1 and n2. However, they are calculated slightly different than in the 8-pin graphics modes. Since two data bytes represent each dot column to print, first divide the total length of the graphic string (following the Select ... Graphics Mode command) by two. These parameters are calculated as follows (assuming a temporary variable n):
First, divide n (the total number of dots needed for the graphics string) by 2, then divide the result by 256. Then n2 is the quotient (the whole number) and n1 is the remainder. If you require less than 256 dots
(columns), then n1 indicates the number of dots and n2 is set to zero. Select 9-Pin Single Density Graphics Mode Enables Single Density 9-pin Graphics mode. Calculating the parameters, n1 and n2, is described previously under Nine-Pin Graphics Modes. n = total number of dots needed, divided by 2 n2 = integer of (n divided by 256) n1 = remainder of the n2 calculation Decimal 27 94 0 n1 n2 Hex 1B 5E 00 n1 n2 ASCII ESC ^ (0) n1 n2 6822 Series 80-Column Printer Users Manual Format Format 94 Format Chapter 5 Control Code Definitions The resolution is 60 dots per inch. Each 8-in line can accommodate 480 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. Select 9-Pin Double Density Graphics Mode Enables Double Density, 9-pin graphics Mode. The parameters, n1 and n2, is described previously under Nine-Pin Graphics Modes Decimal 27 94 1 n1 n2 Hex 1B 5E 01 n1 n2 ASCII ESC ^ (1) n1 n2 The resolution is now 120 dots per inch. Each 8-in line can accommodate 960 columns of graphic dots. A graphic string that exceeds the length of the print line is discarded. 6822 Series 80-Column Printer Users Manual 95 Chapter 5 Control Code Definitions 96 6822 Series 80-Column Printer Users Manual
1 2 3 4 | User Manual part 3 | Users Manual | 1.34 MiB |
6822 Series 80-Column Printer Users Manual 6822 Series 80-Column Printer Users Manual 6 Troubleshooting This chapter helps you correct printing problems that may occur. If you experience a printing problem, you can perform several tests to find and possibly correct the problem. In this chapter you will find these sections:
Checking the power source Aligning the printer mechanism Troubleshooting system components Communications pin-out configurations 6822 Series 80-Column Printer Users Manual 97 Chapter 6 Troubleshooting Checking the Power Source Press any button on the printer control panel. If there is power, the power indicator (green LED) turns on and the printhead moves to its starting position. If the printer emits beeps and any of the other indicators light up or flash, observe the number of beeps and indicator flashes and see Printer Failure Indicators on page 102 If there is no reaction from the printer after you press a key on the control panel, or only the green power light blinks, verify that the power cables are properly connected between the printer mechanism and its power source (internal battery, vehicle cable, or ac). If none of these steps wake up the printer with the problem, then you need to return the printer for service. Internal battery Check the battery and its cable by installing into another known-
good printer. Vehicle cable Attach the printer in question to another vehicle power cable. AC power Plug the printer into another outlet. Aligning the Printer Mechanism If head jams occur, you may need to align the printer mechanism. To align the printer mechanism 1 Open the printer top cover, then install a ribbon cartridge (see page 15) and position the printhead to the far left toward the green thumb wheel. 98 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting 2 Check the area between the printhead and the printer cavity. If the ribbon cartridge touches the pivot frame, the printer mechanism needs realignment. Pivot frame Printhead at far left in the printer 3 Loosen the four screws that hold the mechanism in place using a Phillips screwdriver (see the following illustration). 4 Push the printer mechanism to the right away from the green thumb wheel. 5 Press on the right side of the printer mechanism to the back as far as it will go. Note: In this position, the right back edge of the printer mechanism may touch the pivot frame. The left side must not touch the pivot frame. 6822 Series 80-Column Printer Users Manual 99 Chapter 6 Troubleshooting 6 Hold the printer mechanism in place and tighten the screws in the sequence shown below. 3 Top left 1 Top right 2 Bottom left 4 Bottom right Four screws hold down the printer mechanism Troubleshooting System Components The printing system is composed of four basic components: printer, computer, power source, and communications. Any one of these components can prevent the printer from functioning properly. Verifying the Printer Components Power Source Verification Start by verifying that power is available at the printer. Visually inspect the control panel to verify that the power indicator (green LED) is lit. If it is not, press the Set Page button and note if the power indicator lights up. If it does, the power system is all right. If it does not, press the printer reset button. If the power indicator still does not light, check the power cable, by connecting it to a different printer. If the power indicator works on the new printer, then the cable is all right, and the printer that was originally connected is suspect. If it does not light, then the problem is most likely the cable or the power source. Depending on the results, either replace the cable or return the printer for service. 100 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting Printer Verification If the power indicator works properly and the printer still does not print, then printer errors are noted. If any indicators light when you press the Set Page button, or the printer beeps, refer to the Printer Failure Indicators table on page 102 to determine the problem. If none of the listed conditions are indicated by the beep codes and LEDs, yet the printer does not perform properly, then perform a printer self-test. Press and hold (for several seconds) both Form Feed and the Set Page buttons at the same time, until the printer beeps and all indicator lights come on. The lights change throughout the test, as it progresses. At the end of the self-test, the printer generates a report. This report verifies the following: errors detected during self-test, the error history, and the communication configuration. If the printer self-test report does not print, then reset the printer. If the report does print after resetting, then the printer is all right and the reason the printer does not respond to PC print requests is probably communications or PC related. If the report is partially completed, and a printer error occurs during the printing of self-test, refer to the Printer Failure Indicators table on page 102 for the cause of the printer failure. Perform a power-on-self-test (POST) to test for errors either by resetting the printer or powering it up. If errors occur, audible error codes, along with indicator light status, are produced during POST (see the POST Error Codes table on page 104). If the POST completes without error, try the printer self-test again. If the self-test prints correctly, but the printer does not respond to the PC, then the problem may be related to communications or PC problems. Communications / PC Verification Use the self-test report to verify that the communications protocol options, selected at the printer, match those expected by the host. If they do not match the expected results, reconfigure the printer using the control panel configuration modes described below in the Configuration part of this chapter. 6822 Series 80-Column Printer Users Manual 101 Chapter 6 Troubleshooting If the protocol options match, then the communications cable may be defective. To determine if the cable is working, substitute a new cable. If the PC is suspect, substitute a different PC. A defective computer dock might be another possibility. Understanding Printer Errors Printer Errors are divided into classes:
Runtime errors POST errors, Fatal errors (consisting of flash write errors and EEPROM block errors). Runtime Errors Runtime errors can occur during the course of printing. These errors are displayed on the LEDs, along with beep sequences. This causes the printer to stop printing and enter an error state. Then beep sequences are emitted, LED codes are displayed, the error status may be sent to the host (depending on the protocol), and the printer goes into suspend mode. The printer exits from the suspend mode when the user presses one of the keyboard keys or communications is resumed from the host. The printer also places the printhead in its home position and attempts to recover from the error condition. Until the error condition is corrected, the error procedure does not end, and the error state is not removed. For paper out errors, load paper and press the Set Page button before printing begins. Press the Form Feed button to load the paper to the top of form. The following table provides a listing of printer failure indicators and describes what they mean. Printer Failure Indicators Sets of Beeps 1 beep 1 set of 2 beeps Paper Out Head Jam Low Batt Off Off On 2 blinks Off Off 1 set of 3 beeps Off Off 3 blinks Meaning 12 V under voltage fault (Low Battery) 12 V over voltage fault (Input Voltage too high) 24 V under voltage fault (internal power supply failure) 102 6822 Series 80-Column Printer Users Manual Printer Failure Indicators (continued) Sets of Beeps 1 set of 4 beeps Paper Out Head Jam Low Batt Off 4 blinks Off 1 set of 13 beeps 2 sets of 2 beeps 2 sets of 3 beeps 2 sets of 4 beeps 5 sets of 2 beeps Off Off On Off 5 blinks Off 2 blinks Off On 5 blinks Off 2 blinks Off Off 5 blinks 3 sets of 2 beeps 3 blinks Off 3 blinks 3 sets of 4 beeps 4 sets of 2 beeps 12 sets of 12 beeps Off Off 4 blinks 3 blinks 4 blinks Off Off Off Off Chapter 6 Troubleshooting Meaning 24 V over voltage fault (internal power supply failure) Configuration error printhead over temperature Paper Out Head Jam Paper feed current fault
(Possible paper jam or feed motor failure) printhead over current (printhead failure) Home switch failure printhead short (printhead failure) Operating System software failure Note: The most common errors are Paper Out, Low Battery, and Head Jam. Status indicators on the front panel alert you to these errors. For a description see Understanding the Status Indicators on page 3 Power-On-Self-Test (POST) Errors When you reset the printer, a POST runs to determine why the printer might be failing. Audible error codes, along with indicator light status, are produced during POST if an error occurs. See on POST Error Codes on page 104. To perform a POST 1 Open the printer case. 2 Insert the printer diagnostic cable into the phone jack on the printer and then connect the 9-pin D-Sub plug to your PC. The cable is used during POST to configure the printer, access printer diagnostics, update software, and install new fonts. 6822 Series 80-Column Printer Users Manual 103 Chapter 6 Troubleshooting 3 Press the Reset button to start the POST. When the POST starts, green Power LED will come on followed by a single beep indicating that the printer is active. Note: After the test is completed, all LEDs turn off and the printhead moves to the home position. Only runtime errors or fatal errors are reported until the next time the printer is reset and POST is performed. The printer emits beeps and flashes the LEDs to indicate the cause of any POST errors. POST error codes are described in the following table. POST Error Codes Long Beep 0 0 0 Short Beep 1 0 0 Paper Out Off Off Off Head Jam Off Off Off Low Batt Off Off Off Power Meaning On Off On 1 1 1 1 0 1 1 0 1 2 4 4 0 5 5 0 Off Off Off Off On On On On On On Off Off Off Off On On Off On Off On Off On Off On On On On On On On On On Operational No Power Control program Initial Program Load (IPL) successful Invalid CRC on boot block Invalid CRC on control program or program not found Upper 192K RAM failure Upper 64K RAM failure Diagnostic mode command check Diagnostic flash memory check failed or is not initialized Diagnostic memory write failure Control program IPL Fatal Errors There are two types of fatal errors, flash write errors and EEPROM configuration block errors. These errors are extremely rare, but measures are built into the printer diagnostics to track possible occurrences. Flash Write Errors Errors related to writing or erasing flash are critical errors. These errors cause the printer to stop all processing and produce an LED code and a sequence of beeps. The LED code indicates the address of the segment where the error occurred in octal notation. 104 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting The octal digit changes every four beeps until four octal digits are output. Only four octal digits are output since blocks are 256 bytes in size and flash can be addressed with a total of 0x7ff blocks. The segment address output is the runtime address of the flash block and not the offset of the block within flash. To obtain the block offset within the flash Subtract 0x800 from the address output to determine the block offset. The printer suspends after the processing the error code. When the printer resumes, an error again and the printer suspends again. Reset the printer to correct the error. If a reset does not correct the error, have the printer checked by a qualified service technician. Note: Flash write errors may be unrecoverable. EEPROM Configuration Block Errors Errors related to an invalid configuration block (diagnostic block) produce 13 beeps, and then the printer suspends. It continues to produce this symptom until the configuration block error is corrected. Configuration block errors may be caused by a flash write error or an incorrect printer configuration. Reset the printer to correct the error. If a reset does not correct the error, have the printer checked by a qualified service technician. Self-Test Function Descriptions The self-test performs the following functions. Boot Block Program Verification A CRC (Cyclic Redundancy Check) is performed on the boot block program. The calculated CRC is compared to the CRC embedded in the program module. Control Program Verification A CRC is performed on the control program, which is loaded into writable flash program memory. The calculated CRC is compared to the CRC embedded in the program module. The results of this test are printed on the self-test report. 6822 Series 80-Column Printer Users Manual 105 Chapter 6 Troubleshooting Font Module Verification A CRC is performed on the font modules, which are loaded into writable flash font memory. The calculated CRC is compared to the CRC embedded in the program module. Results are printed on the self-test report. A2D Check Current reading of the A2D sources are performed, and the results are printed on the self-test report. Nonvolatile Diagnostic Memory Verification A CRC is performed on the area of the nonvolatile diagnostic memory that has a CRC over it. Results are printed on the self-test report. Nonvolatile Diagnostic Memory Update The nonvolatile diagnostic memory is updated from the nonvolatile diagnostic memory data shadowed in memory. Detailed Printer Self-Test Perform a self-test to verify printer functions, and provide reporting of printer diagnostics. The self-test performs a series of internal diagnostics and prints the results. When the self-test begins, the beeper sounds for half a second and all LEDs turn on for half a second. Initiating Self-Test While the printer is idle or in Suspend mode, press the Line Feed and Set Page buttons simultaneously to initiate a self-test. Terminating Self-Test Press the Line Feed and Set Page buttons simultaneously to manually terminate a self-test. Self-Test Report Note: This method is recommended to determine printer functionality. 106 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting A self-test is equivalent to a warm start. Both are performed when you simultaneously press Form Feed and Set Page buttons on the control panel for a few seconds. Release the buttons when the printer beeps and all indicators are lit. If you press the buttons for too long, the self-test will not happen and the printer will form-feed one page. As the self-test progresses, the indicator lights change. Internal tests are performed and the two page report is printed. This report provides helpful information in diagnosing and troubleshooting printer problems. When you perform a self-test, the following actions occur:
All LEDs are turned on to verify the lights work A 600 ms beep is emitted to verify the beeper works LEDs flash individually to show progress during internal tests Current voltage and ambient temperature are obtained Validity of diagnostic block program is checked Validity of boot block program is checked Validity of control program is checked Validity of loaded fonts is checked LEDs turn off Self-test report is printed Printer capability is diagnosed by printing the report. Device errors are displayed on the LEDs and emitted by the beeper. The printer then does a warm reset (soft reboot) when an error is encountered or when the self-
test report prints. Understanding the Self-Test Report The self-test report is divided into sections. Refer to page 110 and page 111 for a sample printout. All other values are informational only. Remember that these values are cleared after the self-test. The printer model number is given on line 1 (first line). This identifies the printer type used, in this case the 6822. The 8-digit serial number of the printer is listed on line 4 under the Serial# heading on line 3. The serial number is also on the inside of the printer. In portable printers, raise the printer mechanism to look for the number on the inside back wall. 6822 Series 80-Column Printer Users Manual 107 Chapter 6 Troubleshooting Battery Voltage, (line 13) Indicates the input voltage sampled at the beginning of the self-test. The input range must be between 7.5 and 15 V. The input voltage must be greater than 10.5 V to charge the internal battery. At 7.5 V or less, the Low Batt LED comes on and the printer enters Sleep mode. At 10.5 V or less, the Low Batt comes on but the printer still prints. Auto Feed (line 16) Auto feed is a configurable item. Carriage Return (CR) means no auto linefeed. This is the most common setting for applications using NPCP CR+LF means a line feed will be added to each CR. This setting can produce double-spacing of reports. See Setting the Autofeed on page 29 Interface Mode (line 17) Interface mode lists the interface protocol for the printer. The typical setting is NPCP. Others include DTR with no, odd, or even parity, and IrDA. See Protocol Selection Mode on page 29 Bit Rate (line 18) Bit rate is commonly set to 19200 (19.2K) or 9600 bps. See Selecting the Bit Rate on page 29 A2D History (lines 21 through 25) Shows the recorded history for voltage measurements and temperature measurements. Head Jam History (lines 26 through 29) Provides information on head jams. If the printer is having frequent head jams, these lines can assist in determining the problem. Head Jam History Information Heading Home Command Direction Speed Description Err indicates the home position LED sensor has failed. Indicates which printer command was executed when the head jammed. Indicates which way the head was moving, left is toward the home position and right is away from the home position. Home position is at the extreme left, toward the green thumb wheel. Indicates the acceleration speed of the printhead when the jam occurred. 108 6822 Series 80-Column Printer Users Manual Head Jam History Information (continued) Chapter 6 Troubleshooting Heading Step Temp Position Description The acceleration step at the jam. 0 means no steps were taken, 15 means all steps were taken. 1-14 indicates the printer jammed during acceleration or deceleration. The ambient temperature at the last head jam. The temperature is listed in Celsius. Position of carriage at the time of the jam in 1/720 in = 12 *
step position. Divide the number by 12 to get the step position. There are 512 steps across the page. If it is jammed at position 0, check the printer mechanism alignment. If it is jamming in the middle, it is more likely a dirty ribbon or obstruction in the printheads path. Head Dot Pattern (line 37) Is used to verify the individual dot wires. There should be nine dots. If some dots are missing, it could be a printhead failure or a circuit board failure. Error Log information appears on lines 38-43. This information is cleared after every self-test. Error Log Information Heading PE HJ 12Vu 12Vo 24Vu 24Vo Home Temp OverC HeadS Fault Description Number of paper jams while feeding paper Number of head jams while printhead is moving Number of 12 V under-voltage Number of 12 V over-voltage Number of 24 V under-voltage (head/motor voltage) Number of 24 V over-voltage Number of home detect errors (typically caused by paper scraps or circuit failures) Unused Number of head over-current errors (typically caused by a bad printhead) Number of head driver short errors (typically caused by circuit failures) Number of paper feed motor over current errors (excess current in paper feed motor could indicate circuit failure) 6822 Series 80-Column Printer Users Manual 109 Chapter 6 Troubleshooting Error Log Information (continued) Heading ADErr EEErr Dlink Llink Description Number of A2D conversion failures Number of EEPROM write failures to diagnostic block Number of software memory errors (corruption in internal memory) Number of software memory errors Sample First Page of the Self-Test Note: Lines 15-18 are factory default printer settings. Take note of these lines when reading the self-test report.
------------------------------------------- 1NP6822 2 Copyright 1997, 1998, Intermec Technologies Corporation. All Rights Reserved. 3Serial# MFG Date Hardware Check Repairs Svc Date 412345678 yy/mm/dd ddd-ddd-ddd/dddd (TOP) GO/NG 00 yy/mm/dd 5 ddd-ddd-ddd/dddd (MLB) 6 ddd-ddd-ddd/dddd (PS) 7 ddd-ddd-ddd/dddd (IOB) 8Revisions:..........0000000000303100 9Bootblock: NPBB6822.MOD - Version XX.XX XXXX XXXX GO/NG 10Control Program: npfl6822.mod - Version XX.XX XXXX XXXX GO/NG 11Font Module: nftxxxxx.mod - Version XX.XX XXXX XXXX GO/NG 12Font Module: nftxxxxx.mod - Version XX.XX XXXX XXXX GO/NG 13Battery Voltage: 012.34 Low...../....High 14Total Pages: 123456 15Zero Font Style: O 16Auto Feed: CR 17Interface mode: NPCP 18Bit Rate: 19200 19Cold Starts: 00024 20Warm Starts: 00050 21A2D History 22 Curr Low High Min Max Error Page Count 2324v: 024.00 023.21 023.91 023.21 024.51 027.21 00401 00021 2412v: 012.55 010.91 013.51 010.90 014.50 8.71 00401 00021 25Temp: 023 -020 055 -021 060 000 00401 00021 26Head Jam History 27Total Head Jams: 00186 28Home Command Direction Speed Step Temp Position Page 29 Print Left Const 010 -010 01440 12345 30NPCP History 31Disc Addr Parity IFTS Seq CRC Frame Bind IPLDU 3212345 12345 12345 12345 12345 12345 12345 12345 12345 33IRDA History 34 FramesOk BroadCasts CRC/TMO DISCARD 35rx 1234567890 1234567890 0123456789 0000000000 36tx 1234567890 1234567890 0123456789 0000000000 37HEAD DOT PATTERN 38 Error Log 39PE HJ 12Vu 12Vo 24Vu 24Vo Home Temp OverC HeadS Fault ADErr EEErr 40Dlink Llink 4112345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 4212345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 12345 4312345 12345 12345 12345 12345 12345 12345 12345 12345 12345 110 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting Sample Second Page of the Self-Test Page 2 of the self-test contains the print pattern used to diagnose printer mechanical behavior. The pattern continuously prints the ASCII characters between 33 and 126 decimal inclusive for the entire page, or until you cancel the print by pressing a button on the printer. An example of that rotating pattern is shown below.
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_abcdefghijklmnopqrstuvwxyz{|}~!#$%
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_abcdefghijklmnopqrstuvwxyz{|}~!#$%
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_abcdefghijklmnopqrstuvwxyz{|}~!#$%
0123456789:;<=>?@ABCDEFGHIJKL Self-Test Failure For help, see Miscellaneous Troubleshooting Tips on page 111. Check the power source (internal battery, charge cable, or ac adaptor) for a possible power failure. Miscellaneous Troubleshooting Tips The following table lists actual printing problems, possible causes, and actions you should take to correct a problem. Possible Printer Problems Symptom Printer does not communicate with the mobile computer. Bluetooth unable to connect. Make sure you are in range
(10 cm to 10 m) Double-spacing on application reports but single-
spacing on self-test. Zero prints incorrectly (with or without slash). Solution Test or Cause Incorrect protocol selection. Check lines 17 and 18 on the self-test report for correct bit rate and protocol selection. Change protocol settings through configuration process. Make sure the Bluetooth shutdown timer has not expired Make sure your device is configured to be discoverable and/or connectable. For help, see Bluetooth Configuration Commands and Specifications on page 133. Check line 16 on the self-test report. CR+LF indicates an incorrect configuration for NPCP. Check line 15 on the selftest report for the Zero Font Style setting. For help, see Cleaning the Mask Spring on page 22. If incorrect, adjust the zero print option, see Cleaning the Mask Spring on page 22 6822 Series 80-Column Printer Users Manual 111 Chapter 6 Troubleshooting Possible Printer Problems (continued) Symptom Test or Cause Check line 11 or 12 on the Does not print extended character set missing font. selftest report to see if the NFT0000.MOD file is listed after Font Module. Printer mechanism does not have adequate power for printing. The 12 V may be under or over voltage fault.
(Note: Error lights do not flash if voltage is too high) If power supply, adjust supply voltage to 7.5 to 15 V. Printer emits 1 or 2 beeps or blinking green light is the only indicator. If battery, recharge or replace
(see Installing the Internal Battery on page 10 Printer emits 2 sets of 3 beeps Printer out of paper Printer works but some or all LEDs do not work. Printer does not print Gray ribbon cable connecting control panel board to pivot frame assembly is loose. No voltage No data input Test: Pull paper toward roller. Cause: If paper is resistant:
Paper wrinkled, creased, moist, or perforations missing Adjust supply voltage to 7.5-15 V Tighten computer connections. Paper tray too full White ribbon cables obstructing paper Ensure fewer than 200 3-ply sheets in the deep paper tray and fewer than 50 3-ply sheets in the shallow paper tray. Solution Use the 6820 Printer Tool Kit to reload the font file or send the printer in for hardware repair. Check battery or power supply. Check the printers internal battery, if installed. Check the vehicle charge cable (see 6822 Printer Installation Instructions P/N 931-052-001). Reload paper into printer mechanism. For help, see Loading the Paper Tray on page 13. Call Customer Support
(800-755-5505) or send printer for hardware repair. Voltage too high or low. Check line 13 on the selftest report, under the Battery Voltage heading No paper feed (paper jam or head jam) Torn paper perforation Head Jams due to carriage alignment. Check line 29 on self-test report, under Position heading, for value. Remove torn paper, load and center new paper, readjust pinfeed holders. 112 6822 Series 80-Column Printer Users Manual Possible Printer Problems (continued) Symptom Test or Cause Straighten the white ribbon Replace the paper. cables. No paper feed (paper jam or head jam) Move the printhead manually from side to side. Chapter 6 Troubleshooting Solution If 0, realign mechanism in pivot tray. See Aligning the Printer Mechanism on page 98 Remove ribbon cartridge, move printhead. If smooth, ribbon is jammed. Remove ribbon cartridge, move printhead. If still resistant, mask spring is bent or damaged. Cause: printhead gap adjuster too tight. Cause: Paper scraps found in printer mechanism or around platen. Printer mechanism unlatched
(unlocked). (portable, fixed mount printers) Remove ribbon cartridge and turn knob. If ribbon resists, replace ribbon cartridge (see Installing the Ribbon Cartridge on page 11 Replace the mask spring see Cleaning the Mask Spring on page 22 Set the head gap adjuster to the fifth notch away from the paper see Adjusting the Printhead Gap on page 12 If ribbon cartridge bumps against inside of printer, check white ribbon cable, home position sensor, and four screws. Remove any paper scraps, do a cleaning. Latch (lock) the printer mechanism into place. Perform a self-test. Note: In paper jams or head jams, press the Set Page button to clear the printer before printing can resume. 6822 Series 80-Column Printer Users Manual 113 Chapter 6 Troubleshooting Compatibility Issues Use the following information to determine some compatibility issues that come up relative to the 6822:I Compatibility Issues and Conclusions Issue Does a 6820 ribbon work on the 6822?
Do 6820 applications work on the 6822?
Conclusion Yes. Yes. Applications that work on the 6820 also work on the 6822. Yes. The downloadable character set feature is the same for both the 6820 and 6822. Does the 6822 work with an application that downloads some custom characters to the printer?
Can 6820 printers be replaced with 6822s? Yes. 6822s can be installed on existing 6820 mounting brackets. Understanding Diagnostic Information Diagnostic information is stored in flash to support the hardware configuration, both at time of manufacture and in the field. This includes recording the initial configuration changes to hardware and software, and various environmental statistics helpful in determining why failures are occurring in the field. The flash is provided for storage of critical data that must remain in the unit after power to the unit is lost. The data in the flash is used for diagnostic information for a catastrophic failure, or over the phone with a customer. Diagnostic information is updated and maintained by the printer. All diagnostic information is shadowed in RAM. At the end of every 50 forms, the flash information is updated from the RAM. The printer also updates the diagnostic information for nonrecoverable error, printer resets, printer self-test, and remote polling of diagnostic information. Fields are stored with ID first, then length, then data. The details of the data and the length of the entire field, including ID and Length bytes, are shown in the Diagnostic Information table on page 115. The amount of flash memory reserved for nonvolatile diagnostic memory is 16 K bytes. Printer self-test prints most of the information contained in the diagnostic memory for remote and end-user diagnostic access. 114 6822 Series 80-Column Printer Users Manual Diagnostic Information Field Id 01 Length Description 4 3 Serial Number Date of Manufacture, yy/mm/dd Hardware Configuration ddd-ddd-ddd/ddd (top level P/N) ddd-ddd-ddd/ddd (control board) ddd-ddd-ddd/ddd (power supply) ddd-ddd-ddd/ddd (I/O board) CRC of preceding fields Hardware Revisions: ECNs. applied. 64 ECNs can record separately by number 1-64. Service Repairs: a two-digit field indicating number of times serviced Date of last repair, yy/mm/dd Cold starts since MFG or last repair Warm starts since last cold start Pages printed over life Last high and low voltage extremes on 24 V input over last 50 reports. Extremes stored as 8-bit A2D conversions Voltage extreme history stores min/max 24 V A2D conversions over printer life 24 V voltage error. Voltages greater than 10%
considered errors. A2D error count Form number at last voltage error 24 V error count Last high and low voltage extremes on 12 V input over last 50 reports. Extremes stored as 8-bit A2D conversions Voltage extreme stores min/max 12 V A2D conversions over printer life 12 V error. Voltages less than 10.5 V and greater than 14.5 V are considered errors. A2D value is recorded Page number at last 12 V error 12 V error count Temperature, maximum and minimum over last 50 reports. Set A2D value 7 7 7 7 2 8 1 3 2 2 2 2 2 1 2 2 2 2 1 2 2 2 08 09 10 20 30 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting Total Length Stored as 7 digit BCD set at MFG 39 bytes 6 digit BCD set at MFG 52 digit BCD set at MFG 2 byte binary set at MFG 8 byte bit field 11 bytes 2 BCD digits 6 BCD digits binary digits binary digits binary digits 2 bytes 2 bytes 1 byte 2 bytes 2 bytes 2 bytes 2 bytes 1 byte 2 bytes 2 bytes 2 bytes 8 bytes 11 bytes 11 bytes 11 bytes 115 Chapter 6 Troubleshooting Diagnostic Information (continued) Field Id Length Description 2 Temperature, min/max over printer life. Set A2D value Temperature error. Last A2D conversion below -10 or above 60C recorded Page number at last temperature error Total number of temperature errors Total number of head jams Command 0 = Stop 2 = Print 4 = Print/LF 6 = Seek 8 = Slow Seek 10 = Change Speed 12 = Feed 14 = Wait Speed 00 = Init 01 = Low 10 = High Direction 1 = Left 0 = Right Home Switch 0 = No Error 1 = High Error Acceleration or deceleration stop motor value when jam occurred Ambient temperature when had jam occurred. Set A2D value Form number where head jam occurred Carriage position where head jam occurred IrDA rxFramesOK total frames received OK Total Length 11 bytes Stored as 2 bytes 1 byte 2 bytes 2 bytes 2 bytes binary bits 0-3 bits 4-5 bit 6 bit 7 1 byte binary 1 byte 2 bytes binary 2 bytes binary in 1/720 in 4 bytes 46 bytes 6822 Series 80-Column Printer Users Manual 1 2 2 2 1 1 1 2 2 4 40 60 116 Diagnostic Information (continued) Field Id Length Description 4 Stored as 4 bytes Chapter 6 Troubleshooting Total Length 74 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes IrDA rxFrameCrcErr total frames received with CRC error IrDA rxTotalBytes total bytes received OK 4 bytes IrDA rxFramesDiscardBuf total frames 4 bytes discarded due to no buffer space IrDA rxBroadcastFrames total broadcast frames received OK IrDA rxFramesDiscardHwErr total received frames discarded due to hardware error IrDA txFramesOK total frames transmitted OK IrDA txTotalBytes total bytes transmitted OK IrDA txBroadcastFrames total broadcast frames transmitted OK IrDA txFramesNotTxTimeout total frames not transmitted due to time out IrDA txFramesNotTxHwErr total frames not transmitted due to a hardware error Paper out count Head jam count 12 V low count 12 V high count 24 V low count 24 V high count Home switch error count Unused Over current error count Head short error count Paper fault error count A2D conv. error count EEPROM write error count Double link error count Lost link error count 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 2 bytes 4 bytes 4 bytes 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 70 6822 Series 80-Column Printer Users Manual 117 Chapter 6 Troubleshooting Diagnostic Information (continued) Field Id Length Description 2 2 Out of buffers error count Unused Total Length Stored as 2 bytes 20 * 2 bytes 118 6822 Series 80-Column Printer Users Manual Communications Pin-Out Configurations Chapter 6 Troubleshooting This section shows common cable configurations between a mobile computer or a dock and the printer. Mobile Computer Signal Name Pin #
Pin #
Chassis Ground Charge Input SG (Signal Ground) DSR (Data Set Ready) DTR (Data Terminal Ready) CTS (Clear To Send) RTS (Ready To Send) RXD (Receive Data) TXD (Transmit Data) Dock_A/B_SW shell 8 9 7 2 6 3 5 4 NC shield 1 9 7 6 20 5 4 3 2 12 Wall Mount Printer or Remote Mount Terminal Holder Signal Name NC (No Connection) HHC_CHARGE GND DTR NC RTS CTS TXD RXD Term A/B 8 1 15 9 13 1 25 14 15-Pin DSUB Male 15-Pin to 25-Pin Cable (P/N 216-605-1XX) 15-Pin to 25-Pin Cable (P/N 216-605-1XX) 25-Pin DSUB Male 6822 Series 80-Column Printer Users Manual 119 Chapter 6 Troubleshooting PC Wall Mount Printer Signal Name Pin #
Pin #
Signal Name DTR (Data Terminal Ready)*
RC (Receive Carrier) TC (Transmit Carrier) DCD (Data Carrier Detect) SG (Signal Ground) DSR (Data Set Ready)*
CTS (Clear to Send) RTS (Ready to Send) RXD (Receive Data) TXD (Transmit Data) 20 17 15 8 7 6 5 4 3 2
* Signals are not available on the 6100 Dock 20 17 15 8 7 6 5 4 3 2 NC (No Connection) NC NC NC GND DTR RTS CTS TXD RXD 1 13 14 25 13 1 25 14 25-Pin DSUB Female 25-Pin to 25-Pin Cable (P/N 216-771-XXX) 25-Pin to 25-Pin Cable (P/N 216-771-XXX) 25-Pin DSUB Male 120 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting PC Printer Signal Name Pin #
Pin #
Signal Name TXD (Transmit Data) RXD (Receive Data) RTS (Ready to Send) CTS (Clear to Send) DSR (Data Set Ready) SG (Signal Ground) Chassis Ground 3 2 7 8 6 5 4 5 3 6 7 9 RCT TXD CTS RTS DTR (Data Terminal Ready) GND shield shell shell 8 Chassis Ground Terminal Charge out to computer 1 5 6 9 1 8 9 15 9-Pin DSUB Female 9-Pin to 15-Pin Cable (P/N 226-016-XXX) 15-Pin DSUB Female 9-Pin to 15-Pin Cable (P/N 226-016-XXX) 6822 Series 80-Column Printer Users Manual 121 Chapter 6 Troubleshooting Dock Printer w/6210 Terminal Holder Signal Name Pin #
Pin #
Signal Name TXD (Transmit Data) DTR (Data Terminal Ready) RTS (Ready to Send) RXD (Receive Data) CTS (Clear to Send) DSR (Data Set Ready)*
SG (Signal Ground) 2 20 4 3 5 6 7 4 2 3 5 6 7 9 RXD NC (No Connection) CTS TXD RTS DTR GND open shield shell
* Signal is not available on the 6100 Dock 13 1 25 14 8 1 15 9 25-Pin DSUB Male 25-Pin to 15-Pin Cable (P/N 226-162-XXX) 25-Pin to 15-Pin Cable (P/N 226-162-XXX) 15-Pin DSUB Female 122 6822 Series 80-Column Printer Users Manual Chapter 6 Troubleshooting PC Printer Pin #
Pin #
7 5 3 2 8 6 5 3 2 1 5 1 9 6 1 6 9-Pin DSUB Male Data Communications Cable (P/N 226-270-XXX) RJ-11 Jack Data Communications Cable (P/N 226-270-XXX) The printer has a 25-pin connector with the following pinout designations and signal mnemonics:
Printer Communications Connector 15-Pin DSub 1 2 3 4 5 6 25Pin DSub Signal Name NC 20 4 2 3 5 NC DSR (Data Set Ready) CTS (Clear To Send) RXD (Receive Data) TXD (Transmit Data) RTS (Ready To Send) Type RS-232 RS-232 RS-232 RS-232 RS-232 I/O IN IN IN OUT OUT Description NC (No Connection) Printers DSR Wake up Printers RxD Printers TxD Printers RTS 6822 Series 80-Column Printer Users Manual 123 Chapter 6 Troubleshooting Printer Communications Connector (continued) 15-Pin DSub 7 25Pin DSub Signal Name 6 Type RS-232 DTR (Data Terminal Ready) HHC_CHARGE GND 8 9 9 7 I/O OUT OUT Description Printers DTR 11-13 V, 2 A maximum SG (Signal Ground) POWER POWER 124 6822 Series 80-Column Printer Users Manual A Specifications This appendix provides physical specifications for the 6822 printer models as well as specifications for the media used with the printers. 6822 Series 80-Column Printer Users Manual 125 Appendix A Specifications Specifications Print Speed 230 cps Note: Various print fonts do affect the print speed. Weight Fixed Mount Printers6.55 kg (14.41 lbs) Portable Printers w/ 4000 or 61XX terminal holder5.80 kg (12.75 lbs) w/ 62XX, 600 series, 700 series, or CK60 holder5.67 kg (12.25 lbs) Mounting plate1.93 kg (4.25 lbs) Flat paper tray2.45 kg (5.40 lbs) Compact paper tray2.05 kg (4.50 lbs) Temperature DC Operating -20C to 60C (-4F to 140F) AC Operating -20C to 45C (-4F to 113F) Storage -30C to 70C (-22F to 158F) Humidity Operating10 to 85% noncondensing Storage5 to 95% noncondensing Altitude Operating100 to 5000 m Storage15,000 m Electrical Voltage13.8 VDC (nominal) Current10 mA (idle, sleep mode not charging batteries);
3.5 A (average while printing);
450 mA (charging internal battery);
Up to 1.5 A (charging computer battery) Vibration 12 g RMS for 4 hours 126 6822 Series 80-Column Printer Users Manual Appendix A Specifications ESD 15 kV noncontact and 8 kV contact Battery Shelf Life 1 year at 25C (77 F) 2.3 Ah 12 V sealed lead-acid) Note: The battery goes dead within two weeks when connected to the printer and with no external charge source. Note: A printer and a computer, using the supplied serial cable, can operate up to 9 m (30 ft) apart. Printer Dimensions Listed below are the dimensions of the fixed mount and portable printers. Fixed Mount Printer The base of the fixed mount printer is 32.5 cm (12.75 in) wide by 35.5 cm (14.0 in) front to back. The upper portion varies according to the configurations shown in the following table. Fixed Mount Printer Dimensions Configuration
(with deep paper tray) with 61XX Holder Side Mount with 4000 Series, 62XX, 600 Series, 700 Series, or CK60 Holder Side Mount with 61XX Holder Top Mount with 4000 Series, 62XX, 600 Series, 700 Series, or CK60 Holder Top Mount Width 51.4 cm
(20.25 in) 47.0 cm
(18.5 in) 42.5 cm
(16.75 in) 38.1 cm
(15.0 in) Length 36.8 cm
(14.5 in) 36.8 cm
(14.5 in) 42.6 cm
(16.75 in) 42.6 cm
(16.75 in) Depth 19.1 cm
(7.5 in) 20.3 cm
(8.0 in) 19.1 cm
(7.5 in) 20.3 cm
(8.0 in) 6822 Series 80-Column Printer Users Manual 127 Appendix A Specifications Portable Printer The portable printer may come with a handle, an AC foot, or with a terminal holder top mount. Portable Printer Dimensions Width Configuration 41.9 cm with handle, 61XX Holder Top Mount, and Deep Paper Tray
(16.5 in) with handle, 61XX Holder Top Mount, Shallow Paper Tray 42.5 cm
(16.8 in) 38.1 cm
(15.0 in) 41.9 cm
(16.5 in) with handle, 4000 Series, 62XX, 600 Series, 700 Series, or CK60 Holder Top Mount, and Deep Paper Tray with handle, 4000 Series, 62XX, 600 Series, or 700 Series, or CK60 Holder Top Mount or Fill Plate, and Shallow Paper Tray Length 42.6 cm
(16.8 in) 42.6 cm
(16.8 in) 42.6 cm
(16.8 in) 38.1 cm
(15.0 in) Depth 20.3 cm
(8.0 in) 19.1 cm
(7.5 in) 20.3 cm
(8.0 in) 13.0 cm
(5.1 in) Note: The AC foot adds 6.35 cm (2.5 in) to the length of the printer. Media Specifications Using paper that matches the following specifications ensures optimum 6822 performance. Variation from these specifications, use of aged paper, or use of paper exposed to elements such as dirt or humidity may cause printing problems. The printer works with 1-3 ply carbonless paper that is single-edge glued and designed for sprocket feed. Standard paper size is 8.5 x 11 in or 241 x 305 mm international (8.5 x 12 in). Use 3-ply forms up to a maximum of 0.23 mm (0.009 in) thick. A soft, flexible, rubber type cement applied to one perforation strip only is preferred. The paper should wrap around a 1 1/4 in diameter roll without curl or wrinkle. 128 6822 Series 80-Column Printer Users Manual Material Breakdown The following tables show the material broken down per ply:
14# CBF (Carbonless Back and Front) Appendix A Specifications Basis Weight Caliper Moisture Smoothness (RS) Smoothness (CB) Brightness (Wht) Colors available: White, Canary, Pink, Goldenrod, Blue, Green Under 13.3 lb 2.6 4.0 110 220 86 Over 14.7 lb 3.2 6.0 230 320 90 Target 14 lb 2.9 5.0 165 270 88 15# CF (Carbonless Front) Basis Weight Caliper Moisture Smoothness (RS) Smoothness (CB) Brightness (Wht) Colors available: White, Canary, Pink, Goldenrod, Blue, Green Under 14.43 lb 2.5 4.0 100 100 84 Over 15.8 lb 3.2 6.0 180 180 86 Target 15 lb 3.0 5.0 140 140 85 16# CB (Carbonless Back) Basis Weight Caliper Moisture Smoothness (RS) Smoothness (CB) Brightness (Wht) Opacity (Wht) Colors available: White, Canary, Pink, Goldenrod, Blue, Green Under 15.2 lb 2.8 4.2 120 220 84 78.5 Over 16.8 lb 3.8 6.7 270 320 88 82 Target 16 lb 3.3 5.7 180 270 86 81 6822 Series 80-Column Printer Users Manual 129 Appendix A Specifications 20# OCR Laser Bond Basis Weight Caliper Moisture Smoothness Brightness (Wht) Opacity (Wht) Target 20 lb 4.0 3.8 140 94 85 Under 15.2 lb 3.8 4.7 100 82 84 Over 16.8 lb 4.2 5.0 170 N/A N/A Caliper Breakdown The following table shows the caliper of forms broken down by ply:
Caliper Breakdown 1-Ply (20 lb) 2-Ply (15 lb and 16 lb) 3-Ply (14 lb, 15 lb, and 16 lb) Target 4.0 6.3 9.2 Maximum 4.2 7.0 10.2 130 6822 Series 80-Column Printer Users Manual Understanding the Fanfold Paper Page Layout Appendix A Specifications The following illustration shows the printable area of the lower section of a page of fanfold paper and the upper section of the next page. The Assured Print Area is the best area to use for printing. Page width Assured Print Area 8 inches Max. Assured Print Area 55 lines max
(at 1/16 line spacing)
(area 2) 0.75 inch
(or more) Paper End Detection Position Perforation
...Xyz Abcdef...
(area 1) 1 inch 1 inch
(area 1) Abcdef... ..Xyz
(area 2) 0.75 inch
(or more)
(area 3) 1.833 inches
(11 lines) Printable Area of Fanfold Page You should leave a 1 in margin at both the top and the bottom of the page. This provides for a margin of six lines at 1/6 in line spacing. Even though printing in Area 1 (before or after the perforation) may be possible, you should keep in mind that paper feed precision is reliable only within the Assured Print Area. 6822 Series 80-Column Printer Users Manual 131 Appendix A Specifications The top and bottom margins are represented by Area 1, as shown in the previous illustration. The top margin is defined as the distance between the top edge of the paper and the first row of printed characters. The bottom margin is defined as the distance between the last row of printed characters and the bottom edge of the paper. There is a possibility that printing can start within one line below the perforation and printing could continue beyond the Assured Print Area, however paper feed precision is only reliable with top and bottom margins of approximately one inch. Basically, you should consider there are only 55 lines available for reliable printing. The left and right margins are represented by Area 2. For reliable printing, use a margin of at least 0.75 in for the left and right margins. The Paper End Detection line indicates the point where the Paper Out sensor detects the bottom edge of the paper. Area 3 represents the distance between the Paper End Detection position and the bottom edge of the page. Once the last page of the fanfold paper stack is in the printer, and the printhead has advanced past this Paper End Detection line, printing is no longer reliable. When the bottom end of the last page has advanced through the printer, past the spring plate along the front of the platen, the paper should not reverse back through the printer, because the printer could jam and cause paper feed problems. 132 6822 Series 80-Column Printer Users Manual
1 2 3 4 | User Manual part 4 | Users Manual | 1.07 MiB |
6822 Series 80-Column Printer Users Manual 6822 Series 80-Column Printer Users Manual B Bluetooth Configuration Commands and Specifications Configuration of the Bluetooth radio and software is accomplished using the Bluetooth Configuration Commands listed in this appendix. 6822 Series 80-Column Printer Users Manual 133 Appendix B Bluetooth Configuration Commands and Specifications Using Configuration Commands an h suffix are in hexadecimal a 0x prefix are in hexadecimal a b suffix are in binary All printable characters can be entered directly via the keyboard. Any non-printable characters are entered in binary data format. Numbers are in decimal format except numbers with:
Binary data format is any non seven-bit ASCII data to transmit to the module is encoded in the Internet percent notation. Any hex byte to transmit is preceded by the % sign and encoded in hex ASCII. To send the value 0xF5, the %F5 bytes are transmitted. The %character is always transmitted as %25. Thus, a Bluetooth address could transmit as %00%E0%03%45%F4%6D. Generic format:
<command character><command type><command payload><CR>
<command character> is one character from the set: [A-Z]
<command type> is one character for the set: [0-9]
<command payload> is variable in length.
<CR> is the command terminator. The <command payload> is formed from printable ASCII characters from the code range 0x20 to 0x7E. Codes outside of this range are escaped using the percent (%) character followed by two hexadecimal digits. The percent character is always represented by the three characters %25. The command terminator is character code 0x13 (carriage return), or character code 0x10 (line feed), or character codes 0x13, 0x10 (carriage return, line feed). An example command to set the friendly name to Lens 100% serial module:
F0Lens 100%25 serial module<CR>
Character codes outside of the range of 0x20 to 0x7E are ignored. When using percent (%) to form hexadecimal character codes there must be exactly two hex digits using characters: [0-9, A-F, a-f]. Characters outside of this range cause the command to fail. 134 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Commands that fail return the four character sequence NAK<CR>
Commands that are accepted return the four character sequence ACK<CR>
Commands that return payload data use the format:
<command character><command type><command payload><CR>
<command character> is one character from the set: [a-z]
<command type> is one character for the set: [0-9]
<command payload> is variable in length.
<CR> is the command terminator. The command character is the lower case version of the local host command. Operating Modes The module interface has two modes:
Bluetooth Link Active State In this case the Serial Interface looks like a raw serial port (TxD, RxD, CTS, etc. and GND). There is no intelligence in the Bluetooth module from the serial interface perspective. This mode does not support the command and control modes described below. Bluetooth Link Inactive State This mode exists when a Bluetooth link does not exist. In this case, the serial interface looks like a serial port that supports a number of command and control modes. On reset, the unit comes up in Bluetooth Link Inactive state. After the first Bluetooth connection, the unit goes into Bluetooth Link Active state. It stays in this state until the link is lost because the Master shuts it down or there is an out-of-range condition, it then returns to the Bluetooth Link Inactive state. 6822 Series 80-Column Printer Users Manual 135 Appendix B Bluetooth Configuration Commands and Specifications Command and Control Modes Query Mode Commands Example Commands Command
?<CR>
?F0<CR>
?L<CR>
?C0<CR>
?C1<CR>
?D0<CR>
?D1<CR>
?S1<CR>
?S2<CR>
?S4<CR>
?T0<CR>
?B0<CR>
Command
?<CR>
?F0<CR>
?L<CR>
?C0<CR>
?C1<CR>
?D0<CR>
?D1<CR>
?S1<CR>
?S2<CR>
?S4<CR>
?T0<CR>
?B0<CR>
Function Read ACK Read Friendly Name Read Security Mode Read Connectable Mode Read Page Scan Timing Read Discoverable Mode Read Inquiry Scan Timing Read Class of Device Read Service Name Read PIN Code Read Shutdown Timeout in minutes Read Bluetooth Addresses of all the paired devices Reply ACK<CR>
f0MyFriendlyName<CR>
10<CR> Turn off Encryption, Authentication, and Exclusion 11<CR> Authentication 12<CR> Encryption and Authentication 13<CR> Encryption, Authentication, and Exclusive c0ON<CR>
c11024,512<CR>
d0ON<CR>
d11024,512<CR>
s1001F00<CR>
s2MyServiceName<CR>
s4MyPinCode<CR>
t0Shutdown Timer = 5 minutes<CR>
b0No Devices PairedCR>
136 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Note: These commands are only available over the serial link, not over the air and are not available when the device is in the Bluetooth Link Active State. Set Local Bluetooth Device Name Command Definition Default Example F0<Device Friendly Name><CR>
Device Name String up to 254 bytes long 6822-DDEEFF where DDEEFF is from the
(AABBCCDDEEFF) Bluetooth device address F01Lens 100%25 serial module<CR>
This sets the name to Lens 100% serial module. Set Class of Device/Service Field Command Description Example S1< Class of Device/Service field >
The Class of Device/Service (CoD) field is a 24-bit field defined in the Bluetooth Assigned Numbers document. This field is sent in a HEX ASCII format, most significant byte first. S1001F00<CR> is a common Class of Device value for a basic serial device. Set Service Name Command Description Definition Default Example S2<Service Name>
Sets the service friendly name to send to the remote Bluetooth device in response to a service discovery request. The length of the service name is limited to 32 bytes. Profile Name text name entered into the SDP record for the serial port profile Wireless Printer S3Acme Printer<CR>
Connectable On/Off Command Description C0 <ON|OFF><CR>
Sets the device into connectable mode 6822 Series 80-Column Printer Users Manual 137 Appendix B Bluetooth Configuration Commands and Specifications Example C0OFF<CR> Become non-connectable C0ON<CR> Become connectable Specify Page Scan Timing Command Description Default Example C1<Page_Scan_Interval>,<Page_Scan_Window><
CR>
Sets the Page Scan timing parameters 4096,18 C11024,512<CR>
Note: To enable scanning, the values for Interval and Window must be in the range of 18 to 4096. The Window value must be less than the Interval value. Both values must be zero to disable scanning. Note: Modifying Page Scan Timing can improve connection times, but may adversely affect battery performance. Enable Discoverable Command Description Example D0 <ON|OFF><CR>
Sets the device into discoverable mode D0OFF<CR> Become non-discoverable D0ON<CR> Become discoverable Specify Inquiry Scan Timing Command Description Default Example D1<Inquiry_Scan_Interval>,<
Inquiry_Scan_Window><CR>
Sets the Inquiry Scan timing parameters 4096,18 D11024,512<CR>
138 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Set Encryption/Authentication: PIN CODE Command Description Default Example S4<PIN code>
PIN Code Pin code can be NULL and as long as 16 characters S4%00 NULL PIN code S4MyPinCode <CR>
Manage Security Modes This command controls the security access mode and device pairing. The modes available are:
L0 Disable encryption, authentication and exclusion L1 Enable authentication L2 Enable encryption and authentication L3 Enable encryption, authentication and exclusive Mode L0 allows any remote device to connect. Mode L1 require the remote device to be authenticated by a PIN request. The PIN code for the module is set to a userspecified value with the S4 command. Currently the default PIN is the NULL string. Mode L2 adds encryption to the Bluetooth link. Mode L3 adds exclusive connection to one specific Bluetooth device. In this mode only connection requests from the initial device are allowed. Connections from other devices are rejected even if they supply the correct PIN code. Device pairing and bonding are associated with this command and works as follows:
After an L command is executed the current device pairing and bonding is deleted. The next device to connect becomes paired and bonded to the module. In Modes L1 and L2, other devices are allowed to connect but only the first device to connect is paired and bonded. Other devices are always required to supply a PIN code to complete the connection. 6822 Series 80-Column Printer Users Manual 139 Appendix B Bluetooth Configuration Commands and Specifications In Mode L3, only one device is allowed to connect. This device is paired and bonded and needs to supply the PIN code only on the initial connection. Note: Some of the Bluetooth user interfaces cannot supply a NULL string as a PIN code. Use the S4 command to specify a PIN code that is not NULL. Read Module Version Command Description V0<CR>
Displays the firmware build version currently running V0<CR>
Returns: v1yyyymmddHHMM<CR>
Note: This command responds with the requested data, only not the ACK<CR>. Example Read Local Device Address Command Description Returns V1<CR>
Displays the local device address v1%xx%xx%xx%xx%xx%xx<CR>
Note: This command responds with the requested data, only not the ACK<CR>. Example:
Sent: V1<CR>
Received: v1%00%2C%C6%03%45%39 140 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Set Shutdown Timing Command Description Range Default Example T0<Time in Minutes><CR>
Time Integer value 0 implies never expire the timer 0-270 minutes 120 T0120<CR> This sets the shutdown timer to 120 minutes. Clear Link Key Table Command Description Default Example B0<CLR><CR>
Clear Pair or Bonding command cleans up all of the link key and Bluetooth address combination PSKEYs. None B0CLR<CR> This clears all saved link keys. Understanding Adapter States or Modes The Bluetooth adapter connects to an internal serial port of the 6822, providing serial print data over a transparent Bluetooth link, running a Serial Port Profile (SPP). Printing is primarily accomplished over a Bluetooth link using the SPP protocol with a 700 Series or CK60 Mobile Computer. If the relevant printer configuration allows it, a 700 Series or CK60 in a terminal holder charges normally. 6822 Series 80-Column Printer Users Manual 141 Appendix B Bluetooth Configuration Commands and Specifications The Bluetooth adapter allows for four states or modes to be available. Each state is dependent upon either the pin states on the terminal holder connector or the programming connector on the adapter described later. Bluetooth Adapter States or Modes State State/mode 1 2 Bluetooth Printing Passthrough printing HHC_A/B pin 0 0 HHC_DTR pin 0 1 3 4 Bluetooth Reconfiguration Bluetooth programming cabled 1 X 0 X Comments Bluetooth printing/Bluetooth self-test Printing from 700 Series or CK60s allowed to pass through the Bluetooth adapter transparently. Reconfiguring Bluetooth module via 700 Series or CK60s. Programming Bluetooth module via programming cable State 1 - In addition to allowing normal Bluetooth printing, this state also allows for a 700 Series or CK60 in the terminal holder to perform a Bluetooth self-test. State 2 is a Transparent Pass Through mode available for all 700 Series and CK60s. During this mode, the Bluetooth module is shut down and does not communicate. State 3 (Bluetooth reconfiguring using a 700 Color (730, 740, 741, 750, 751, 760, 761) or CK60). This state is unavailable when a 700 Monochrome (705, 710, 720) is used, since the A/B pin is unavailable. State 4 allows for programming the Bluetooth module via its SPI pins. This state is also used for manufacturing tests. To be in this state, the 700 Series or CK60 must not have an open terminal holder COM port and the specially designed programming adapter must be engaged. The interfaces on the Bluetooth adapter that allow for the different modes are detailed below:
142 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications 700 Series or CK60 to 6822 Pass Through Note: Pass through printing requires shutting down the Bluetooth portion of the adapter. To reenable Bluetooth functionality after you finish pass through printing, press a button on the control panel to wake the printer. When DTR on the 700 Series or CK60 is set, the adapter board automatically opens a path between the 700 Series of CK60 and the 6822 Transition/DC Board and powers down the Bluetooth module. Testing the DSR pin to reflect DTR allows the mobile computer to differentiate between a Bluetooth-equipped terminal holder and a non-Bluetooth equipped terminal holder. 700 Series, CK60, or CN3 to Bluetooth Module Communication Interface The Bluetooth adapter allows a 700 Series, CK60, or CN3 to communicate directly with the Bluetooth module under two circumstances. When the configuration settings of the Bluetooth module are to print. When the Bluetooth module requires reconfiguration. 6822 Series 80-Column Printer Users Manual 143 Appendix B Bluetooth Configuration Commands and Specifications Power Management Flow Diagram Bluetooth Power Management Flow Diagram 144 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Radio Power On/Off Mechanism Note: The shutdown timer configuration is addressed in Appendix A Bluetooth Configuration Commands. As stated earlier, the Bluetooth adapter, including the Bluetooth radio shuts down after a configurable time (default is two hours of idle time). To wake the Bluetooth adapter, the 6822 is powered on by any button push on the printer control panel. There are two ways to shutdown the Bluetooth module power:
A 700 Series, CK60, or CN3 initiates a pass through mode, or The Bluetooth module sends a shutdown signal after a configurable amount of time. Default is two hours of idle time. Note: The adapter complies with Bluetooth 1.1 specification, including bonding for authentication and enabling encryption. Persistent Storage These settings do not reset after a coldboot is performed on the printer:
Bluetooth Bonding Enable/Disable Bluetooth Encryption Enable/Disable Bluetooth Passkey Bluetooth Bonding List (Link Keys) Bluetooth Device Name Bluetooth Class of Device Discoverable setting Connectable setting Radio Shutdown Timer Timeout (default two hours of idle time) System Behavior/Software Considerations Discoverability The default mode is Discoverable. When configured to be discoverable, the adapter is discoverable at all times, except when:
an active Bluetooth connection exists 6822 Series 80-Column Printer Users Manual 145 Appendix B Bluetooth Configuration Commands and Specifications you have just completed a pass-through printing print job the shutdown time has elapsed (default shutdown time is two hours). Connectability The default mode is connectable. When configured to be connectable, the printer is connectable at all times, except when:
an active Bluetooth connection exists you have just completed a pass-through printing print job the shutdown time has elapsed (default is two hours). Link Loss The 6822 Bluetooth adapter is able to recover from broken Bluetooth connections, including out-of-range, interference, power failure, or other conditions resulting in a broken connection. It returns to its previous Discoverable/Connectable state after a lost connection. Master/Slave Printer participates in a Bluetooth connection as the slave device. The Class of Device is 0x040680 which translates to a Service Class of Rendering, a Major Device Class of Imaging, and a Minor Device Class of Printer. The 6822 Bluetooth includes an SDP record that allows the printer to report an SPP instance with a service name of Wireless Printer. The default Bluetooth device name is 6822-DDEEFF, where DDEEFF matches the respective portion of the Bluetooth device address (AA:BB:CC:DD:EE:FF). If the printer the adapter is connecting to is known, the service name is changed to 6822-SN, where SN is replaced with the serial number of the 6822. The 6822 Bluetooth adapter can save 16 link keys across cold boots. Link keys are saved in a circular list. The 17th link key replaces the first, the 18th replaces the 2nd, and so on. Remote Configuration You can query the following items:
Discoverable State [Get/Set]
Connectable State [Get/Set]
146 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications Bondable State [Get/Set] (Authentication) Encryption State [Get/Set]
Device Name [Get/Set]
Device Address[Get]
Class of Device[Get/Set]
Service Name [Get/Set]
Bluetooth Profile [Get]
Bluetooth Passkey [Set] (Get the fact that it is set) Radio Shutdown Timeout Bluetooth Performance Range Operating range is expected to range from a minimum separation of 10 cm to over 10 m with a 700 Color or CK60. Link Loss can occur when going in or out of range while communicating with other Bluetooth devices. Diagnostics Capabilities The Bluetooth radio settings are available to a user. The 6822 Bluetooth adapter sends a printout of Bluetooth information to the printer upon receiving a message from a 700 Series or CK60 in a terminal holder. An example self-test is shown below:
6822 Bluetooth Adapter Firmware:Version YYYY MMDD HHMM Bluetooth Configuration:
Device Address:0002371A0FD3 Device Name:6822-9843252 Discoverable:Yes Connectable:Yes Authentication:No Encryption:No Passkey:Not Applicable (or Key present if Authentication is enabled) Stored Link Keys:2 of 16 Power Management:
Shut Off Timer:120 minutes 6822 Series 80-Column Printer Users Manual 147 Appendix B Bluetooth Configuration Commands and Specifications The Passkey entry either states Not Applicable or Key Present depending on the Authentication state. Applications A 6822 Bluetooth Information application that prints the Bluetooth self-
test information on the 6822 can be installed on your 700 Series or CK60. To use the Bluetooth Information application 1 Insert the 700 Series or CK60 in the terminal holder on the 6822. 2 Tap the Start > Programs > the 6822 BT Information icon on your 700 Series or CK60 computer. 3 Press the Set Page button on the printer control panel to wake the printer. 4 From the 6822 Bluetooth Self-Test screen, tap the Trigger Self Test button to print the information. 148 6822 Series 80-Column Printer Users Manual Appendix B Bluetooth Configuration Commands and Specifications System Qualification Operation Resilience Normal operation of the Bluetooth system is available in environments with radio backbones, including 802.11b, Spectrum 24, and OpenAir technologies. Environmental Specifications Temperature Operating Temperature -20 to 60C (-4 to 140F) Storage Temperature -30 to 70C (-22 to 158F). Temperature Test Results Test Operating Cold to Hot Transition Operating Hot to Cold Transition Humidity Operating Storage Range
-20C to 50C
(-4F to 122F) 50C to 20C
(122F to -4F) Comments External condensation allowed, internal prohibited Speed shall not degrade 5% to 95% RH non-condensing 90% 25 to 60C (48 to 140F) no condensation 90% 25 to 60C (48 to 140F) no condensation Altitude
-100 to 5000 meters Vibration Test Results Test Quasi-Random 3 axis Dynamic Induced Shock Operating Storage When packed Frequency Acceleration Comments 12 g RMS, for 4 hours 20 g on 3 axis 1 G 5 Hz to 80 Hz 3 G 5 Hz to 80 Hz 5 to 55 Hz 2 G 6822 Series 80-Column Printer Users Manual 149 Appendix B Bluetooth Configuration Commands and Specifications Vibration Test Results (continued) Test Sweep Duration Directions Comments 10 minutes (half cycle) 1 hour x, y, and z No external or internal damage should be found after the vibration test, and the unit should operate normally. Unpackaged Drop 2 feet to concrete Terminal Inspection Minimum of 30,000 insertions for the terminal holder. Safety/Regulatory/Agency Requirements The Bluetooth adaptor must meet the electrical safety requirements for Information Technology Equipment. The test configuration must include a portable computer connected to the 6822, continuously printing the letter H. At least 6dB of margin below the relevant limits must be demonstrated. Safety, Regulatory, Agency Requirements Option Product Safety Requirement UL Listed per UL 1950 / UL 60950 (printer and AC power supply) CSA C22.2, No. 950 TUV/GS License per EN 60950 (printer, AC power supply) CB Report for EN 60950 covering all country deviations (Printer, ac power supply) UL 2089 (for cigarette lighter-style adapters) SAE J1113 or ISO 7637 FCC Class B (US); Industry Canada ICES-003 Class B (Canada) CISPR 22 Class B, including telecom port conducted (Europe) AS/NZS 3548 (Australia/New Zealand); CNS 13438 (Taiwan) IEC 61000-4-2Electrostatic Discharge IEC 61000-4-3Radiated RF Field Vehicle Power Interfaces EMC Digital device radiated and conducted emissions EN 55024 Immunity
(Europe) 150 6822 Series 80-Column Printer Users Manual Safety, Regulatory, Agency Requirements (continued) Option EMC (continued) Appendix B Bluetooth Configuration Commands and Specifications Requirement IEC 61000-4-4Electrical Fast Transients IEC 61000-4-5Surge IEC 61000-4-6Conducted RF IEC 61000-4-8Magnetic Field IEC 61000-4-11Voltage Dips and Interrupts (AC printers only). IEC 61000-3-2 (per Amendment 14) Class A if under 70 Watts loaded to 90% of rated value, Class D if over 70 Watts loaded to 90% of rated value IEC 61000-3-3 Voltage Fluctuation and Flicker. Bluetooth Radio - Modular radio approval is required. BT SIG approval is not mandatory but BT SIG GAP and SPP conformance is a prerequisite. FCC Part 15.247 (US) RSS-210 (Canada - indoor operation, unlicensed. Outdoor operation IF restricted to 2.450-2.4835 GHz) RSS-139 (Canada - indoor/outdoor operation, licensed. 2.400-
2.4835GHz) RSS-102 (Canada) - RF Exposure/SAR. Keep antennas more than 8 inches from operator to avoid SAR testing EN 300 328-1 & -2; EN 300 489-1 & 17 (Europe). SCT (Mexico) IEC950 2nd Edition, 4th Amendment or IEC 60950 3rd Edition, resulting in a GS Mark and a CB Report addressing all country deviations S Mark for Argentina for any device connecting directly to the AC mains CCIB Approval for China for any device connecting directly to the AC mains Mexico NOM 19 as applicable AC power supply
(Europe) Radio Type Approval Additional Approvals 6822 Series 80-Column Printer Users Manual 151 Appendix B Bluetooth Configuration Commands and Specifications Default Configuration Default Configurations Setting Bluetooth Authentication Discoverable Connectable Class of Device Service Name Device Name Baud Rate Data Bits Stop Bits Parity Handshaking Radio Shutdown Timeout Default Off True True 0x040680 Wireless Printer 6822-DDEEFF 19,200 8 1 None Hardware 120 minutes 152 6822 Series 80-Column Printer Users Manual C Cross-Reference Tables A set of cross-reference tables are provided to assist you in locating control codes and escape sequences. The default settings are also included. 6822 Series 80-Column Printer Users Manual 153 Appendix C Cross-Reference Tables Control Codes and Escape Sequences The following table contains a complete alphabetized list of control codes, including single character control codes and escape sequences, as an aid to locating the control codes defined in Chapter 5 Control Code Definitionsor detailed definitions of these control codes, refer to the pages shown in the Page column of this table. Control Codes and Escape Sequences Index Description A Absolute Print Position, Set B Backspace Beeper Category General Printer Control General Printer Control General Printer Control Bottom-Up Printing, Select General Printer Control Byte:
Double Byte Character Sets Char. Sets, User Defined Multi-Byte Character Sets Char. Sets, User Defined Single Byte Character Sets Char. Sets, User Defined C Cancel Line Carriage Return Channel:
General Printer Control General Printer Control Page
<Hyper link10>
page 65
<Hyper link10>
page 62
<Hyper link10>
page 63
<Hyper link10>
page 66
<Hyper link10>
page 82
<Hyper link10>
page 82
<Hyper link10>
page 82
<Hyper link10>
page 63
<Hyper link10>
page 63 154 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Clear Vertical Tabs in Channel Category Tabs and Tab Setting Select Vertical Tab Channel Tabs and Tab Setting Set Vertical Tabs in Channel Tabs and Tab Setting Page
<Hyper link10>
page 81
<Hyper link10>
page 81
<Hyper link10>
page 81 Character:
Define Intercharacter Space Define User-Defined Characters Disable Printing of Character Graphics Double Byte Character Sets Enable Printing of Character Graphics Multi-Byte Character Sets Print Character Graphics Select Default Character Set Select National Character Set Select User-Defined Character Set Char. Sets, User Defined Char. Sets, User Defined Char. Sets, User Defined Char. Sets, User Defined Char. Style & Text Mode <Hyper link10>
page 74
<Hyper link10>
page 86
<Hyper link10>
page 90
<Hyper link10>
page 82
<Hyper link10>
page 89
<Hyper link10>
page 82
<Hyper link10>
page 90
<Hyper link10>
page 87
<Hyper link10>
page 83
<Hyper link10>
page 87 Char. Sets, User Defined Char. Sets, User Defined Char. Sets, User Defined Char. Sets, User Defined Char. Sets, User Defined 6822 Series 80-Column Printer Users Manual 155 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Single Byte Character Sets Category Char. Sets, User Defined User Defined Characters Char. Sets, User Defined Code Code page Selection Char. Sets, User Defined Disable Printing of Codes 128-255 Char. Sets, User Defined Enable Printing of Codes 128-255 Char. Sets, User Defined Expand Printable Code Area Char. Sets, User Defined Page
<Hyper link10>
page 82
<Hyper link10>
page 86
<Hyper link10>
page 83
<Hyper link10>
page 88
<Hyper link10>
page 88
<Hyper link10>
page 88 156 6822 Series 80-Column Printer Users Manual Control Codes and Escape Sequences Index (continued) Appendix C Cross-Reference Tables Description Condensed (compressed):
Cancel Condensed Mode Copy ROM to RAM Select Condensed Mode D Default Character Set, Select Define Intercharacter Space Define User-Defined Characters Delete Double:
Cancel Double Strike Mode Cancel Double Wide Mode Cancel Double Wide Mode (one line only) Double Byte Character Sets Select Double Strike Mode Category Page Char. Sets, User Defined Char. Sets, User Defined Char. Style & Text Mode <Hyper link10>
page 71
<Hyper link10>
page 86 Char. Style & Text Mode <Hyper link10>
page 71
<Hyper link10>
page 87 Char. Style & Text Mode <Hyper link10>
page 74
<Hyper link10>
page 86
<Hyper link10>
page 63 Char. Sets, User Defined General Printer Control Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 73
<Hyper link10>
page 82 Char. Style & Text Mode <Hyper link10>
page 72 Char. Sets, User Defined 6822 Series 80-Column Printer Users Manual 157 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Select Double Wide Mode Select Double Wide Mode (one line only) E Elite Pitch, Select Emphasized Mode, Cancel Emphasized Mode, Select Expand:
Cancel Double Wide (expanded) Mode Cancel Double Wide Mode (one line only) Expand Printable Code Area Select Double Wide (expanded) Mode Select Double Wide Mode (one line only) F Form Feed G General Printer Control Functions Graphics:
158 Page Category Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 74 Char. Sets, User Defined Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 73
<Hyper link10>
page 88 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 72
<Hyper link10>
page 64
<Hyper link10>
page 62 General Printer Control General Printer Control 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Disable Printing of Character Graphics Category Char. Sets, User Defined Eight-Pin Graphics Modes Graphics Functions Reassign Graphics Mode Graphics Functions Select Graphics Mode Graphics Functions Select High-Speed Double Density Mode Graphics Functions Select Low-Speed Double Density Mode Graphics Functions Select Low-Speed Quadruple Density Mode Graphics Functions Select Single Density Graphics Mode Graphics Functions Enable Printing of Character Graphics Char. Sets, User Defined Nine-Pin Graphics Modes Graphics Functions Select 9-Pin Double Density Graphics Mode Graphics Functions Select 9-Pin Single Density Graphics Mode Graphics Functions Print Character Graphics Char. Sets, User Defined Page
<Hyper link10>
page 90
<Hyper link10>
page 91
<Hyper link10>
page 91
<Hyper link10>
page 91
<Hyper link10>
page 92
<Hyper link10>
page 92
<Hyper link10>
page 92
<Hyper link10>
page 92
<Hyper link10>
page 89
<Hyper link10>
page 93
<Hyper link10>
page 93
<Hyper link10>
page 93
<Hyper link10>
page 90 H Half Speed:
6822 Series 80-Column Printer Users Manual 159 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Cancel Half-Speed Printing Category General Printer Control Select Half-Speed Printing General Printer Control Page
<Hyper link10>
page 64
<Hyper link10>
page 64 Horizontal:
Clear Horizontal Tabs Perform Horizontal Tab Set Horizontal Tabs I Inactivity Time for Sleep Mode, Set Intercharacter Space, Define Italic:
Cancel Italic Mode Select Italic Mode L Left Margin, Set Length:
Tabs and Tab Setting Tabs and Tab Setting Tabs and Tab Setting
<Hyper link10>
page 79
<Hyper link10>
page 78
<Hyper link10>
page 79
<Hyper link10>
page 64 Char. Style & Text Mode <Hyper link10>
page 74 General Printer Control Char. Style & Text Mode <Hyper link10>
page 75 Char. Style & Text Mode <Hyper link10>
page 75
<Hyper link10>
page 70 Page Formatting Set Page Length (inches) Page Formatting Set Page Length (lines) Page Formatting
<Hyper link10>
page 68
<Hyper link10>
page 68 160 6822 Series 80-Column Printer Users Manual Control Codes and Escape Sequences Index (continued) Appendix C Cross-Reference Tables Description Line, Cancel Line Feed:
Perform Line Feed Category General Printer Control General Printer Control Perform n/216 inch Line Feed General Printer Control Perform n/216 inch Reverse Line Feed General Printer Control Line Spacing:
Select 1/6 inch Line Spacing Page Formatting Select 1/8 inch Line Spacing Page Formatting Select 7/72 inch Line Spacing Page Formatting Select n/72 inch Line Spacing Page Formatting Select n/216 inch Line Spacing Page Formatting Page
<Hyper link10>
page 63
<Hyper link10>
page 65
<Hyper link10>
page 65
<Hyper link10>
page 65
<Hyper link10>
page 69
<Hyper link10>
page 68
<Hyper link10>
page 69
<Hyper link10>
page 69
<Hyper link10>
page 69 M Margin:
Set Left Margin Set Right Margin Master Select Page Formatting Page Formatting
<Hyper link10>
page 70
<Hyper link10>
page 69 Char. Style & Text Mode <Hyper link10>
page 75 6822 Series 80-Column Printer Users Manual 161 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Master Reset, Perform Mode:
Cancel Condensed Mode (compressed) Cancel Double Strike Mode Cancel Double Wide (expanded) Mode Cancel Double Wide Mode (one line only) Cancel Emphasized Mode Cancel Italic Mode Cancel Subscript/Superscript Mode Cancel Underline Mode Select Condensed Mode (compressed) Select Double Strike Mode Select Double Wide (expanded) Mode Select Double Wide Mode (one line only) Category General Printer Control Page
<Hyper link10>
page 65 Char. Style & Text Mode <Hyper link10>
page 71 Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 75 Char. Style & Text Mode <Hyper link10>
page 78 Char. Style & Text Mode <Hyper link10>
page 78 Char. Style & Text Mode <Hyper link10>
page 71 Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 72 162 6822 Series 80-Column Printer Users Manual Control Codes and Escape Sequences Index (continued) Appendix C Cross-Reference Tables Description Select Emphasized Mode Select Elite Pitch Select Italic Mode Select Pica Pitch Select Subscript Mode Select Superscript Mode Select Underline Mode Set Inactivity Time for Sleep Mode Multi-Byte Character Sets N National Character Set, Select O One Line Only:
Cancel Double Wide Mode (one line only) Select Double Wide Mode (one line only) Select Unidirectional Printing (one line only) Page Category Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 75 Char. Style & Text Mode <Hyper link10>
page 77 Char. Style & Text Mode <Hyper link10>
page 77 Char. Style & Text Mode <Hyper link10>
page 77 Char. Style & Text Mode <Hyper link10>
page 78
<Hyper link10>
page 64
<Hyper link10>
page 82
<Hyper link10>
page 83 Char. Sets, User Defined Char. Sets, User Defined General Printer Control Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 72
<Hyper link10>
page 67 General Printer Control 6822 Series 80-Column Printer Users Manual 163 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description P Page:
Category Set Page Length (inches) Page Formatting Set Page Length (lines) Page Formatting Perforation:
Cancel Skip Over Perforation Page Formatting Set Skip Over Perforation Page Formatting Page
<Hyper link10>
page 68
<Hyper link10>
page 68
<Hyper link10>
page 71
<Hyper link10>
page 70 Pitch:
Select Elite Pitch Select Pica Pitch Position:
Char. Style & Text Mode <Hyper link10>
page 74 Char. Style & Text Mode <Hyper link10>
page 77 Set Print Position (absolute) General Printer Control Set Print Position (relative) General Printer Control Print:
Cancel Half-Speed Printing General Printer Control Cancel Unidirectional Printing General Printer Control Disable Printing of Character Graphics Char. Sets, User Defined
<Hyper link10>
page 65
<Hyper link10>
page 66
<Hyper link10>
page 64
<Hyper link10>
page 67
<Hyper link10>
page 90 164 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Disable Printing of Codes 128-255 Category Char. Sets, User Defined Enable Printing of Character Graphics Char. Sets, User Defined Enable Printing of Codes 128-255 Char. Sets, User Defined Expand Printable Code Area Char. Sets, User Defined Print Character Graphics Char. Sets, User Defined Select Bottom-Up Printing General Printer Control Select Half-Speed Printing General Printer Control Select Top-Down Printing General Printer Control Select Unidirectional Printing General Printer Control Select Unidirectional Printing (one line only) General Printer Control Set Print Position (absolute) General Printer Control Set Print Position (relative) General Printer Control R Reset, Perform Master General Printer Control Page
<Hyper link10>
page 88
<Hyper link10>
page 89
<Hyper link10>
page 88
<Hyper link10>
page 88
<Hyper link10>
page 90
<Hyper link10>
page 66
<Hyper link10>
page 64
<Hyper link10>
page 66
<Hyper link10>
page 67
<Hyper link10>
page 67
<Hyper link10>
page 65
<Hyper link10>
page 66
<Hyper link10>
page 65 6822 Series 80-Column Printer Users Manual 165 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Reverse n/216 inch Line Feed, Perform Category General Printer Control Right Margin, Set Page Formatting ROM to RAM, Copy Char. Sets, User Defined S Single Byte Character Sets Char. Sets, User Defined Skip:
Cancel Skip Over Perforation Page Formatting Set Skip Over Perforation Page Formatting Sleep Mode, Set Inactivity Time for General Printer Control Page
<Hyper link10>
page 65
<Hyper link10>
page 69
<Hyper link10>
page 86
<Hyper link10>
page 82
<Hyper link10>
page 71
<Hyper link10>
page 70
<Hyper link10>
page 64 Space:
Define Intercharacter Space Select 1/6 inch Line Spacing Select 1/8 inch Line Spacing Select 7/72 inch Line Spacing Select n/72 inch Line Spacing Page Formatting Page Formatting Char. Style & Text Mode <Hyper link10>
page 74
<Hyper link10>
page 69
<Hyper link10>
page 68
<Hyper link10>
page 69
<Hyper link10>
page 69 Page Formatting Page Formatting 166 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Select n/216 inch Line Spacing Category Page Formatting Page
<Hyper link10>
page 69 Strike:
Cancel Double Strike Mode Select Double Strike Mode Subscript/Superscript:
Cancel Subscript/Superscript Mode Select Subscript Mode Select Superscript Mode Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 72 Char. Style & Text Mode <Hyper link10>
page 78 Char. Style & Text Mode <Hyper link10>
page 77 Char. Style & Text Mode <Hyper link10>
page 77 T Tab:
Clear Horizontal Tabs Tabs and Tab Setting Clear Vertical Tabs Tabs and Tab Setting Clear Vertical Tabs in Channel Tabs and Tab Setting Perform Horizontal Tab Tabs and Tab Setting Perform Vertical Tab Tabs and Tab Setting Select Vertical Tab Channel Tabs and Tab Setting
<Hyper link10>
page 79
<Hyper link10>
page 80
<Hyper link10>
page 81
<Hyper link10>
page 78
<Hyper link10>
page 80
<Hyper link10>
page 81 6822 Series 80-Column Printer Users Manual 167 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Set Horizontal Tabs Category Tabs and Tab Setting Set Vertical Tabs Tabs and Tab Setting Set Vertical Tabs in Channel Tabs and Tab Setting Time for Sleep Mode, Set Inactivity General Printer Control Top-Down Printing, Select General Printer Control Page
<Hyper link10>
page 79
<Hyper link10>
page 80
<Hyper link10>
page 81
<Hyper link10>
page 64
<Hyper link10>
page 66 U Underline:
Cancel Underline Mode Select Underline Mode Unidirectional:
Char. Style & Text Mode <Hyper link10>
page 78 Char. Style & Text Mode <Hyper link10>
page 78 Cancel Unidirectional Printing General Printer Control Select Unidirectional Printing General Printer Control Select Unidirectional Printing (one line only) General Printer Control User Defined Characters:
Copy ROM to RAM Char. Sets, User Defined Define User-Defined Characters Char. Sets, User Defined
<Hyper link10>
page 67
<Hyper link10>
page 67
<Hyper link10>
page 67
<Hyper link10>
page 86
<Hyper link10>
page 86 168 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Disable Printing of Character Graphics Category Char. Sets, User Defined Disable Printing of Codes 128-255 Char. Sets, User Defined Enable Printing of Character Graphics Char. Sets, User Defined Enable Printing of Codes 128-255 Char. Sets, User Defined Expand Printable Code Area Char. Sets, User Defined Print Character Graphics Char. Sets, User Defined Select Default Character Set Char. Sets, User Defined Select User-Defined Character Set Char. Sets, User Defined V Vertical:
Clear Vertical Tabs Tabs and Tab Setting Clear Vertical Tabs in Channel Tabs and Tab Setting Perform Vertical Tab Tabs and Tab Setting Select Vertical Tab Channel Tabs and Tab Setting Set Vertical Tabs Tabs and Tab Setting Page
<Hyper link10>
page 90
<Hyper link10>
page 88
<Hyper link10>
page 89
<Hyper link10>
page 88
<Hyper link10>
page 88
<Hyper link10>
page 90
<Hyper link10>
page 87
<Hyper link10>
page 87
<Hyper link10>
page 80
<Hyper link10>
page 81
<Hyper link10>
page 80
<Hyper link10>
page 81
<Hyper link10>
page 80 6822 Series 80-Column Printer Users Manual 169 Appendix C Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Set Vertical Tabs in Channel Category Tabs and Tab Setting Page
<Hyper link10>
page 81 W Wide:
Cancel Double Wide (expanded) Mode Cancel Double Wide Mode (one line only) Select Double Wide (expanded) Mode Select Double Wide Mode (one line only) Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 73 Char. Style & Text Mode <Hyper link10>
page 72 Single Character Control Code Definitions This table contains control codes between 00h and 7Fh, and provides definitions for the ASCII symbols as used in the table on the next page and in format definitions in Chapter 5 Control Code Definitions. Single Character Control Code Definitions Used as a terminator for several escape sequences. ASCII Description NUL SOH STX ETX EOT ENQ ACK BEL Hex 00 01 02 03 04 05 06 07 Dec 0 1 2 3 4 5 6 7 170 Beeper: sounds buzzer for 1/10 of a second. 6822 Series 80-Column Printer Users Manual Page
<Hyper link10>
page 63 Appendix C Cross-Reference Tables Single Character Control Code Definitions (continued) Dec 8 Hex 08 ASCII Description BS Backspace: moves printhead one space to left. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 0E 0F 10 11 12 13 14 15 16 17 18 09 0A 0B HT Horizontal Tab: moves printhead to next tab stop. LF Line Feed: moves paper to next line. VT Vertical Tab: moves paper to next vertical tab stop 0C FF Form Feed: advances paper to top of next page. 0D CR Carriage Return: moves printhead to left margin. SO Shift Out: selects double-wide mode (one-line-only) SI Shift In: selects condensed (compressed) mode DLE DC1 DC2 DC3 DC4 Device Control 1: sets printer online (not currently used) Device Control 2: cancels condensed mode (compressed) <Hyper link10>
page 71 Device Control 3: sets printer offline (not currently used) Device Control 4: cancels double-wide mode (one line only) NAK SYN ETB CAN Cancel Line: clears all characters out of print buffer. Page
<Hyper link10>
page 62
<Hyper link10>
page 78
<Hyper link10>
page 65
<Hyper link10>
page 79
<Hyper link10>
page 64
<Hyper link10>
page 63
<Hyper link10>
page 72
<Hyper link10>
page 71
<Hyper link10>
page 73
<Hyper link10>
page 63 6822 Series 80-Column Printer Users Manual 171 Appendix C Cross-Reference Tables Single Character Control Code Definitions (continued) Dec 25 26 27 28 29 30 31 32 127 Hex 19 1A 1B 1C 1D 1E 1F 20 7F ASCII Description EM SUB ESC FS GS RS US SP DEL Escape: defines start of escape sequence. Space Character Delete: deletes last character in print buffer. Page
<Hyper link10>
page 63 172 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Escape Sequence Quick Reference The following table is a quick reference between the escape sequences listed in ascending order, according to numeric values. For detailed definitions, see Chapter 5 Control Code Definitions. Escape Sequence Quick Reference Decimal ESC SO ESC SI ESC US (0) ESC US (1) ESC SP n ESC ! n ESC $ n1 n2 ESC % (0) ESC % (1) ESC & NUL k1 k2 s1 d1...d11 ESC * m n1 n2 ESC + n d1...dn ESC - 0*
ESC - 1*
ESC / c ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 ESC 6 ESC 7 ESC <
ESC : NUL NUL NUL ESC ? s n Description Select Double-Wide (expanded) Mode (one line only) Select Condensed Mode (compressed) Select Top-Down Printing Select Bottom-Up Printing Define Inter-Character Space Master Select Set Print Position (absolute) Select Default Character Set Select User-Defined Character Set Define User-Defined Characters Select Graphics Mode Print Character Graphics Cancel Underline Mode Select Underline Mode Select Vertical Tab Channel Select 1/8 inch Line Spacing Select 7/72 inch Line Spacing Select 1/6 inch Line Spacing Select n/216 inch Line Spacing Select Italic Mode Cancel Italic Mode Enable Printing of Codes 128-255 Disable Printing of Codes 128-255 Select Unidirectional Printing (one line only) Copy ROM to RAM Reassign Graphics Mode 6822 Series 80-Column Printer Users Manual 173 Appendix C Cross-Reference Tables Escape Sequence Quick Reference (continued) Decimal ESC @
ESC A n ESC B NUL ESC B n1 n2 ... nk NUL ESC C n ESC C NUL n ESC D NUL ESC D n1 n2 ... nk NUL ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 ESC L n1 n2 ESC M ESC N n ESC O ESC P ESC Q n ESC R n0 n1 n2 ESC R n ESC S 0*
ESC S 1*
ESC T ESC U 0*
ESC U 1*
ESC W 0*
ESC W 1*
ESC Y n1 n2 ESC Z n1 n2 Description Perform Master Reset Select n/72 inch Line Spacing Clear Vertical Tabs Set Vertical Tabs Set Page Length (lines) Set Page Length (inches) Clear Horizontal Tabs Set Horizontal Tabs Select Emphasized Mode Cancel Emphasized Mode Select Double-Strike Mode Cancel Double-Strike Mode Expand Printable Code Area Perform n/216 inch Line Feed Select Single-Density Graphics Mode Select Low-Speed Double-Density Graphics Mode Select Elite Pitch Set Skip Over Perforation Cancel Skip Over Perforation Select Pica Pitch Set Right Margin Code page Selection Select National Character Set Select Superscript Mode Select Subscript Mode Cancel Superscript/Subscript Mode Cancel Unidirectional Printing Select Unidirectional Printing Cancel Double-Wide (expanded) Mode Select Double-Wide (expanded) Mode Select High-Speed Double-Density Graphics Mode Select Low-Speed Quadruple-Density Graphics Mode 174 6822 Series 80-Column Printer Users Manual Appendix C Cross-Reference Tables Escape Sequence Quick Reference (continued) Decimal ESC ^ (0) n1 n2 ESC ^ (1) n1 n2 ESC b c NUL ESC b c n1 n2 ... nk NUL ESC j n ESC l n ESC s 0*
ESC s 1*
ESC t (0) ESC t (1) ESC z n ESC \ n1 n2 Description Select 9-pin Single Density Graphics Mode Select 9-pin Double Density Graphics Mode Clear Vertical Tab Channel Set Vertical Tabs in Channel Perform n/216 inch Reverse Line Feed Set Left Margin Cancel Half-Speed Printing Select Half-Speed Printing Disable Printing of Character Graphics Enable Printing of Character Graphics Set Inactivity Time for Sleep Mode Set Print Position (relative) Factory-Installed Printer Defaults Factory-Installed Printer Defaults Function Carriage position Character set Code page Codes 128-255 Condensed (compressed) Double-Strike Double-Wide Emphasized Graphics mode Half-Speed printing Intercharacter space International character sets Italic Justification Default Value At left margin Normal (not user defined) 0 Disabled Disabled Disabled Disabled Disabled Not selected Disabled Zero (0) Disabled Disabled Left justification 6822 Series 80-Column Printer Users Manual 175 Appendix C Cross-Reference Tables Factory-Installed Printer Defaults (continued) Function Keyboard, printer Language Line Spacing Margin, left Margin, right MSB control NLQ Page length Default Value Enabled USA 1/6 inch 0 80 Disabled Disabled 11 inch (66 lines with Pica pitch) Enabled Pica (10 characters per inch) 10 seconds Top-down, bidirectional Paper end sensor Pitch Power off sleep timer Printer Code Area Expansion Disabled Printing direction Redefinition of graphic modes Disabled Skip over perforation Disabled Disabled Subscript/Superscript Tabs, horizontal Set to default tabs (every 8 column) 1 line feed each tab, channel = 0 Set to current line Disabled Disabled (bidirectional) Removed Tabs, vertical Top of form Underline Unidirectional printing User defined character set The settings in the previous table are installed in the printer at the factory. To restore the printer to these defaults, see Reset Button on page 4 for instructions. The default settings listed below can be restored to the printer, as described in Chapter 4 Using the 6820 Printer Configuration Utility. 176 6822 Series 80-Column Printer Users Manual Printer Default Settings Appendix C Cross-Reference Tables Function Zero print option Autofeed configuration Protocol Parity Bit Rate Default Value Zeros are printed with a slash CR (carriage return added at end of line without line feed) NPCP (NORAND Portable Communications Protocol) N/A (for NPCP) 19.2K 6822 Series 80-Column Printer Users Manual 177 Appendix C Cross-Reference Tables 178 6822 Series 80-Column Printer Users Manual D Printer Font Test Jobs This appendix contains a sample print job for each font available on your 6822 printer. 6822 Series 80-Column Printer Users Manual 179 Appendix D Printer Font Test Jobs About the Printer Font Jobs You can perform these tests yourselves. Load the font of choice from the Toolkit CD into flash memory. After downloading the desired font, use any of the sample print jobs to reveal the character locations within the printer memory. The sample test print jobs are formatted as a memory mapped and could be referenced to select a desired character. These test print jobs originated from running a C program by a person with specific knowledge of how to generate such a report (print job). The C program demonstrates how a programmer could access the printer font modules within flash memory to select desired character. You do not need more than one font module loaded. Any ONE of:
nft00932.mod, nft00936.mod, nft00949.mod, or even nft00950.mod Asian fonts can be used. These are distributed via the NPTK6822 toolkit
(including the source code). These print jobs are in this appendix:
BIG5.C which creates BIG5950.TXT CHINA.C which creates GB2312.TXT IBM437.C which creates IBM437.TXT JAPAN.C which creates JIS932.TXT KOREA.C which creates KOREA.TXT NATION.C which creates NATION.TXT Big 5 Traditional Chinese Character Set This program generates a text file, big5950.txt, to copy to a 6822. The text file illustrates the use of the BIG 5 traditional Chinese character set. Install the BIG 5 character font (nft00950.mod) using the Printer Configuration Utility. To have big5950.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl big5.c /link slibce graphics 2 Run big5.exe to create big5950.txt. 3 Copy this text file to the appropriate printer port. 180 6822 Series 80-Column Printer Users Manuall Simplified Chinese Character Set Appendix D Printer Font Test Jobs This program generates a text file, gb2312.txt, that to copy to a 6822. The text file illustrates the use of the Simplified Chinese character set. Install the Simplified Chinese character font (nft00936.mod) using the Printer Configuration Utility. To have gb2312.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl china.c /link slibce graphics 2 Run china.exe to create gb2312.txt. 3 Copy this text file to the appropriate printer port. IBM 437 Code Page Character Set This program generates a text file, ibm437.txt, to copy to a 6822. The text file illustrates the use of the IBM 437 code page character set. Install the IBM 437 character font (nft00437.mod) using the Printer Configuration Utility. To have ibm437.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl ibm437.c /link slibce graphics 2 Run ibm437.exe to create ibm437.txt. 3 Copy this text file to the appropriate printer port. Japanese (Shift JIS) Character Set This program generates a text file, jis932.txt, to copy to a 6822. The text file illustrates the use of the JIS character set. Install the JIS character font (nft00932.mod) using the Printer Configuration Utility. To have jis932.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl japan.c /link slibce graphics 2 Run japan.exe to create jis932.txt. 6822 Series 80-Column Printer Users Manual 181 Appendix D Printer Font Test Jobs 3 Copy this text file to the appropriate printer port. Korean Character Set This program generates a text file, korea.txt, to copy to a 6822. The text file illustrates the use of the KSC5601 character set. Install the KSC5601 character font (nft00949.mod) using the Printer Configuration Utility. To have korea.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl korea.c /link slibce graphics 2 Run korea.exe to create korea.txt. 3 Copy this text file to the appropriate printer port. International Character Set This program generates a text file, nation.txt, to copy to a 6822. The text file illustrates the international character sets available for use in the default character set. Install the default character set font (nft00000.mod) using the Printer Configuration Utility. To have nation.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl nation.c /link slibce graphics 2 Run nation.exe to create nation.txt. 3 Copy this text file to the appropriate printer port. 182 6822 Series 80-Column Printer Users Manuall I Index 6822 Series 80-Column Printer Users Manual 183 Index Numerics 4000 Series Terminal Holder 2 61XX Terminal Holder 2 62XX Terminal Holder 2 700 series computer pinout configuration 122 inserting in terminal holder 17 A ActiveSync disabling 54 enabling 46 Alpha keyboard Windows 95/98 38 B Big 5 traditional Chinese character set 82 Bluetooth adapter applications 148 class of device 146 default device name 146 link keys 146 link loss 146, 147 master/slave 146 performance range 147 query items 146 SDP record 146 self-test 147 Bluetooth Configuration Commands connectable on/off 137 manage security modes 139 query mode commands 136 specify inquiry scan timing 138 specify page scan timing 138 BM0_1_DI7ZVP_ZBNA0B_7SKU RH_2 2 Buffers I/O buffer 58 print (image) buffer 58 C Cables 15pin to 25pin 25pin to 15pin 25pin to 25pin 120 9pin to 15pin 121 Change configuration parameters error messages 54 Windows 95/98 37 Chinese Character sets Big 5 traditional 82 GB 2312 82 Code page file Class of device Greek 85 Hebrew 83 international 83 Japanese, shift JIS 82 Korean, KSC5601 82 Bluetooth adapter 146 NFT00932.MOD, 932 file 82 NFT00936.MOD, 936 file 82 NFT00949.MOD, 949 file 82 NFT00950.MOD, 950 file 82 connectable on/off 137 manage security modes 139 query mode 136 specify inquiry scan timing 138 specify page scan timing 138 Communications connector pinouts Commands 123 Configuration ActiveSync installation setting 6820 printer configuration enabling 46, 54 Windows 95/98 28 overview of operation Windows 2000/XP 46 Windows 2000/XP 49 Windows 2000/XP 46 Windows 95/98 29 Connectable on/off 137 Control code/escape sequence table working memory 154 Control codes crossreference tables control codes & escape sequences index 154 Copy fonts 184 6822 Series 80-Column Printer Users Manual Windows 95/98 35 Crossreference tables index 154 control codes & escape sequences configuration file, default.pcf D Default printer settings Windows 95/98 Windows 95/98 default.pcf default configuration Windows 95/98 Bluetooth adapter Device name E Error messages printer settings Windows 2000/XP Escape sequence/control code table Escape sequences crossreference (to definitions) F Factory defaults Windows 95/98 Fixed mount printer description Flash space available Windows 2000/XP Windows 95/98 Fonts copy Windows 95/98 Chinese character set G GB 2312 Greek character sets H Hebrew character sets Horizontal tabs Index perform perform horizontal tab I I/O buffer Image buffer Inactivity time set inactivity time for sleep mode Windows 95/98 Installation (configuration utility) International character set J Japanese character set (Shift JIS) K Korean character set (KSC5601) KSC5601 Korean character set L Line feed (LF) Line spacing perform line feed LINE FEED button setting paper for printing select 1/8inch line spacing Bluetooth adapter Bluetooth adapter Link keys Link loss
, M Manage security modes Master/slave Modes Bluetooth adapter inactivity time for sleep mode N nft00932.mod nft00936.mod code page 932 code page 936 code page 949 code page 950 nft00949.mod nft00950.mod 6822 Series 80-Column Printer Users Manual 185 Index nptk6820.exe toolkit self-extracting Windows 95/98 O Operation pinfeed holders
, P Parameters Windows 95/98 Portable printer description Print (image) buffer Print head printer alignment set to third notch Windows 95/98 Printer descriptions fixed mount portable Print head gap Printer default settings Printer mechanism alignment Printer problems Printer, get from (load configuration) Printer, save configuration to Windows 95/98 Windows 95/98 Programs, selftest control program verification Windows 2000/XP Windows 95/98 Bluetooth adapter Q Query items Query mode commands R Range Bluetooth adapter Reset button portable Windows 95/98 install Ribbon cartridge Restore defaults to printer rpgpconf.exe configuration utility, application Windows 95/98 rpgpconf.ini installation file Windows 95/98 S Save (update working configuration) SDP record Save to printer Windows 95/98 Windows 95/98 Bluetooth adapter Bluetooth adapter setting paper for printing SET PAGE button Setting 6820 printer configuration Selftest Windows 95/98 Settings, default Shift JIS, Japanese character set Sleep mode set inactivity time for sleep mode Sleep mode, set activity time for Space remaining in flash Windows 2000/XP Windows 95/98 Spacing, line select 1/8inch line spacing Specify inquiry scan timing Specify page scan timing T Tabs and tab setting functions perform horizontal tab horizontal tabs Terminal holder Time inserting 700 series computer set inactivity time for sleep mode Tool kit self-extracting archive file Windows 95/98 186 6822 Series 80-Column Printer Users Manual Traditional, Bit 5, Chinese character set Troubleshooting Bluetooth adapter diagnostics possible printer problems POST error codes selftest U Utility, configuration Windows 95/98 installation operation Index Windows 2000/XP Windows 95/98 V Verifications Visible moving parts in mechanism printer components W Wall mount printer Working configuration Windows 2000/XP Windows 95/98 6822 Series 80-Column Printer Users Manual 187 Index 188 6822 Series 80-Column Printer Users Manual Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com 2008 Intermec Technologies Corporation. All rights reserved. 6822 Series 80-Column Printer Users Guide
*935-013-001*
P/N 935-013-001
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2008-04-30 | 2412 ~ 2462 | DTS - Digital Transmission System | Class II permissive change or modification of presently authorized equipment |
2 | 1851.25 ~ 1908.75 | PCE - PCS Licensed Transmitter held to ear | ||
3 | 2008-03-21 | 1851.25 ~ 1908.75 | PCE - PCS Licensed Transmitter held to ear | |
4 | 2412 ~ 2462 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 4 | Effective |
2008-04-30
|
||||
1 2 3 4 |
2008-03-21
|
|||||
1 2 3 4 | Applicant's complete, legal business name |
Intermec Technologies Corporation
|
||||
1 2 3 4 | FCC Registration Number (FRN) |
0022970339
|
||||
1 2 3 4 | Physical Address |
9680 Old Bailes Rd.
|
||||
1 2 3 4 |
Fort Mill, South Carolina 29707
|
|||||
1 2 3 4 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 4 | TCB Application Email Address |
d******@nwemc.com
|
||||
1 2 3 4 |
c******@curtis-straus.com
|
|||||
1 2 3 4 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
1 2 3 4 |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
|||||
app s | FCC ID | |||||
1 2 3 4 | Grantee Code |
EHA
|
||||
1 2 3 4 | Equipment Product Code |
02CN3
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 4 | Name |
B**** R********
|
||||
1 2 3 4 | Title |
VP & GC, Honeywell Scanning & Mobility
|
||||
1 2 3 4 | Telephone Number |
803-8********
|
||||
1 2 3 4 | Fax Number |
803-8********
|
||||
1 2 3 4 |
b******@honeywell.com
|
|||||
app s | Technical Contact | |||||
1 2 3 4 | Firm Name |
Advance Data Technology Corporation (Hwa Ya)
|
||||
1 2 3 4 | Name |
G****** C******
|
||||
1 2 3 4 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 2 3 4 |
Taoyuan Hsien, 333
|
|||||
1 2 3 4 |
Taiwan
|
|||||
1 2 3 4 | Telephone Number |
886-3******** Extension:
|
||||
1 2 3 4 | Fax Number |
886-3********
|
||||
1 2 3 4 |
G******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 2 3 4 | Firm Name |
Advance Data Technology Corporation
|
||||
1 2 3 4 | Name |
E**** W******
|
||||
1 2 3 4 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 2 3 4 |
Taoyuan Hsien, 333
|
|||||
1 2 3 4 |
Taiwan
|
|||||
1 2 3 4 | Telephone Number |
886-3******** Extension:
|
||||
1 2 3 4 | Fax Number |
886-3********
|
||||
1 2 3 4 |
e******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 3 4 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 3 4 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 4 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 4 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 3 4 | PCE - PCS Licensed Transmitter held to ear | |||||
1 2 3 4 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | CN3 | ||||
1 2 3 4 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 4 | Modular Equipment Type | Does not apply | ||||
1 2 3 4 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 4 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 4 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 4 | Grant Comments | Grant conditions from original and subsequent filings if any under this FCC ID are applicable, also the following concerning this Class II permissive change: Output power is conducted. Collocated transmitter operating configurations have been evaluated as described in this filing with optional FCC ID: EHABTS080-1 (mobile printer-Model 6820). Other collocation configurations require separate evaluation. For mobile operating configurations, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter not described in this application. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Collocated body-worn operating configurations have been evaluated as described in previous filings; other collocation configurations require separate evaluation. SAR compliance for body-worn operating configurations is limited to the specific configurations tested for in previous filings. Body-worn operations are restricted to the specific belt-clips / holsters / accessories tested for in previous filings. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values for single- and co-transmit configurations under this FCC ID are: Part 15 head 1.03 W/kg; body-worn 0.09 W/kg Part 22 head 0.92 W/kg; body-worn 0.31 W/kg Part 24 head 0.65 W/kg; body-worn 0.52 W/kg Co-transmit head 0.87 W/kg; body-worn 0.52 W/kg | ||||
1 2 3 4 | Grant conditions from original and subsequent filings if any under this FCC ID are applicable, also the following concerning this Class II permissive change: Output power is ERP for Part 22 and EIRP for Part 24. Collocated transmitter operating configurations have been evaluated as described in this filing with optional FCC ID: EHABTS080-1 (mobile printer-Model 6820). Other collocation configurations require separate evaluation. For mobile operating configurations, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter not described in this application. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Collocated body-worn operating configurations have been evaluated as described in previous filings; other collocation configurations require separate evaluation. SAR compliance for body-worn operating configurations is limited to the specific configurations tested for in previous filings. Body-worn operations are restricted to the specific belt-clips / holsters / accessories tested for in previous filings. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values for single- and co-transmit configurations under this FCC ID are: Part 15 head 1.03 W/kg; body-worn 0.09 W/kg Part 22 head 0.92 W/kg; body-worn 0.31 W/kg Part 24 head 0.65 W/kg; body-worn 0.52 W/kg Co-transmit head 0.87 W/kg; body-worn 0.52 W/kg | |||||
1 2 3 4 | Output power is ERP for Part 22 and EIRP for Part 24. Collocated transmitter operating configurations have been evaluated as described in this filing; other collocation configurations require separate evaluation. SAR compliance for body-worn operating configurations is limited to the specific configurations tested for this filing. Body-worn operations are restricted to the specific belt-clips / holsters / accessories tested for this filing. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values for single- and co-transmit configurations under this FCC ID are: Part 15 head 1.03 W/kg; body-worn 0.09 W/kg Part 22 head 0.92 W/kg; body-worn 0.31 W/kg Part 24 head 0.65 W/kg; body-worn 0.52 W/kg Co-transmit head 0.87 W/kg; body-worn 0.52 W/kg. Class II Permissive Change for adding a new collocation configuration with Intermec printer, model PW50, FCC ID: EHA-RN41A, as described in this filing. Other collocation configurations require separate evaluation. | |||||
1 2 3 4 | Output power is conducted. Collocated transmitter operating configurations have been evaluated as described in this filing; other collocation configurations require separate evaluation. SAR compliance for body-worn operating configurations is limited to the specific configurations tested for this filing. Body-worn operations are restricted to the specific belt-clips / holsters / accessories tested for this filing. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values for single- and co-transmit configurations under this FCC ID are: Part 15 head 1.03 W/kg; body-worn 0.09 W/kg Part 22 head 0.92 W/kg; body-worn 0.31 W/kg Part 24 head 0.65 W/kg; body worn 0.52 W/kg Co-transmit head 0.87 W/kg; body-worn 0.52 W/kg. Class II Permissive Change for adding a new collocation configuration with Intermec printer, model PW50, FCC ID: EHA-RN41A, as described in this filing. Other collocation configurations require separate evaluation. | |||||
1 2 3 4 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 4 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 4 | Firm Name |
Northwest EMC, Inc.
|
||||
1 2 3 4 |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
|||||
1 2 3 4 | Name |
G**** K******
|
||||
1 2 3 4 |
R******** C****
|
|||||
1 2 3 4 | Telephone Number |
503-8********
|
||||
1 2 3 4 |
886-3******** Extension:
|
|||||
1 2 3 4 | Fax Number |
503-8********
|
||||
1 2 3 4 |
886-3********
|
|||||
1 2 3 4 |
g******@nwemc.com
|
|||||
1 2 3 4 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402 | 2480 | 0.0016 | ||||||||||||||||||||||||||||||||||||
1 | 2 | 15C | 2412 | 2462 | 0.175 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 24E | 1851.25 | 1908.75 | 0.766 | 2.5 ppm | 1M43F9W | ||||||||||||||||||||||||||||||||||
2 | 2 | 22H | 824.7 | 848.31 | 0.724 | 2.5 ppm | 1M40F9W | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 24E | 1851.25 | 1908.75 | 0.766 | 2.5 ppm | 1M43F9W | ||||||||||||||||||||||||||||||||||
3 | 2 | 22H | 824.7 | 848.31 | 0.724 | 2.5 ppm | 1M40F9W | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
4 | 1 | 15C | 2402 | 2480 | 0.0016 | ||||||||||||||||||||||||||||||||||||
4 | 2 | 15C | 2412 | 2462 | 0.175 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC