Intermec Technologies Corporation EMC Test Laboratory DOC. NO.: 577-500-979 2450 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 APPENDIX N, 6110 Users Manual and DoC insert REPORT NO: 010312-1 DATE: March 12, 2001 Page 1 of 3 FCC ID: EHARFID2450PCC-5 Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 2450 PC Card 5 2.4 GHz Spread Spectrum Transmitter REPORT NO: 010312-1 DATE: March 12, 2001 APPENDIX N DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE INTERMEC 6110 TERMINAL Compliance Statement Insert Device Name: Hand-held Computer Model Number: 6110 The responsible party for the compliance of this device is:
Intermec Technologies Corporation 6001 36th Avenue West Everett, WA 98203 USA
(425) 348-2600 CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. RIM 902 Mobitex Radio Users FCC ID: EHAWANRIM902-6100 WARNING. Per the FCC RF (radio frequency) exposure requirements:
(1) Antennas must be supplied and installed as recommended by Intermec Technologies Corporation to ensure compliance to FCC RF exposure requirements.
(2) The user shall not touch the terminal antenna and must remain 22-mm (7/8 of and inch) from the center of the antenna while the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated with the vehicle dock, a 23-cm (9-inch) passing distance must be maintained from any body part of the user, or near-by persons, and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to control RF exposure.
(5) The correct mounting for external or remote antennas is on a ground plane (e.g., a vehicle rooftop) with the antenna positioned such that the minimum 23-cm distance is maintained from any edge of the vehicle rooftop to the remote antenna. RIM 802 ARDIS Radio Users FCC ID: EHAWANRIM802 WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF exposure requirements.
(2) The user shall not touch the terminal antenna and is to remain 15-mm (5/8 of and inch) from the center of the antenna while the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to control RF exposure.
(5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning the antenna such that the minimum 20 cm is kept from any edge of the vehicle rooftop and the remote antenna. INTERMEC RFID 2450 PC Card Radio Users FCC ID: EHARFID2450PCC-5 WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use. INTERMEC RFID 2450 PC Card Radio Users Canada ID: xxxxxxxxxx WARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. The end user is responsible to obtain the license. WARNING: per Canada RSS-102, RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use. 578-100-0xx Revision A
*578-100-0xx*
*578-100-0xx*
Page 1 of 2 FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the radio of television receiving antenna. Increase the separation between the computer equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance Telephone Installation Warning Notices This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. The following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment from potential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have been read, understood, and complied with. Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Installation do tlphone : avertissements Les avertissements qui suivent s'appliquent tout quipement qui peut tre branch aux lignes ou systemes tlphoniques. Pour votre scurit personnelle et pour protger l'quipement de tout dommage lectrique ou physique potentiel, NE PAS brancher un ordinateur tablette lectronique ou ses priphriques aux lignes tlphoniques ou quipements avant que les avertissements suivants aient t lus, compris et observs:
humides. Ne jamais installer de cblage tlphonique pendant un orage lectrique. Ne jamais installer de prise tlphonique dans un endroit humide moins que la prise ait t spcifiquement conue pour tre utilise dans les endroits Ne jamais toucher les fils de tlphone ou de l'quipement terminal non isols moins que la ligne tlphonique n'ait t dbranche de l'interface rseau. 578-100-0xx Revision A
*578-100-0xx*
*578-100-0xx*
Page 2 of 2