FCC ID: HN2-F4-915-LP RFID Bar Code Printer

 

Installation & Operation P/N 1-960467-01 Edition 2 March 2000 EasyCoder F4 Bar Code Label Printer Preface Contents Preface Table of Contents.................................................................................1 Copyright Information ........................................................................4 Trademarks ..........................................................................................4 FCC Notice (U.S.A.) ...........................................................................5 DOC Notice (Canada).........................................................................5 GS Notice (Germany) .........................................................................5 EU Standard EN 55022 (The European Union) ...............................5 Declaration of Conformity (CE) ........................................................6 1. Introduction Introduction..........................................................................................7 Safety Requirements ...........................................................................8 Product Labelling................................................................................8 2. Print a Label Introduction..........................................................................................9 Intermec Fingerprint .........................................................................12 Intermec Direct Protocol ..................................................................15 3. Installation Unpacking..........................................................................................16 Front View .........................................................................................17 Rear View ..........................................................................................18 Media Compartment .........................................................................19 Print Mechanism ...............................................................................22 Connections .......................................................................................23

Power....................................................... .....................................23

Computer.................................................... ..................................23 Controls and Indicators .................................................................... 24

Control Lamps............................................... ............................. 24

Display..................................................... .................................... 24

Keyboard.................................................... ................................. 24

Beeper ...................................................... ....................................25 4. Starting Up Startup Files.......................................................................................26 Electronic Keys..................................................................................26 Memory Card ....................................................................................27 Power On............................................................................................27 Display Messages at Startup.............................................................28 EasyCoder F4 Installation & Operation Edition 2, March 2000 Part No. 1-960467-01 Intermec EasyCoder F4 Installation & Operation Ed. 2 1 Preface Contents, cont'd. 5. Paper Load Tear-Off..............................................................................................29 Tear-Off with Quick-Load................................................................33 Peel-Off..............................................................................................35 External Supply .................................................................................39 6. Setting Up the Printer Description........................................................................................ 40 Default Setup .....................................................................................41 Setup Parameters:..............................................................................42

Serial Communication:................................................................42

- Baudrate......................................................................................42

- Character Length .......................................................................43

- Parity...........................................................................................43

- Stop Bits......................................................................................43

- Flow Control...............................................................................43

- New Line ................................................................................... 44

- Receive Buffer........................................................................... 44

- Transmit Buffer ......................................................................... 44

Net Communication .....................................................................45

- New Line ....................................................................................45

Feed Adjust:..................................................................................45

- Startadjust...................................................................................45

- Stopadjust....................................................................................45

Media: ...........................................................................................46

- Media Size..................................................................................46

- Media Type.................................................................................48

- Paper Type ..................................................................................48

- Contrast.......................................................................................50

- Testfeed.......................................................................................50

Print De nes:................................................................................50

- Head Resistance .........................................................................50

- Testprint ......................................................................................50

- Print Speed .................................................................................52

- LTS (Label-Taken Sensor).........................................................52 Network.........................................................................................52 7. Setup Mode Entering the Setup Mode at Installation ..........................................53 Navigating in Setup Mode ................................................................54 Setup Mode Overviews.....................................................................55 2 Intermec EasyCoder F4 Installation & Operation Ed. 2 Preface Contents, cont'd. 8. Intermec Shell Startup Program Introduction....................................................................................... 60 Starting Up with Intermec Shell.......................................................61 Intermec Shell Diagram................................................................... 64 Terminal Setup ..................................................................................65 Starting Terminal Setup...............................................................65 Solving Communication Problems .............................................65 Using Terminal Setup ..................................................................66 Selecting an Application ..............................................................67 Changing the Setup ......................................................................68 Exiting Terminal Setup................................................................69 Line Analyzer ....................................................................................70 9. Options Introduction........................................................................................71 Side Doors..........................................................................................72 Rewind Unit.......................................................................................72 Paper Supply Spool ...........................................................................72 3 Adapter..........................................................................................72 Quick-Load Guides ...........................................................................73 Label-Taken Sensor ...........................................................................73 EasySet bar Code Wand....................................................................73 Real-Time Clock................................................................................73 Interface Boards ................................................................................74 10. Troubleshooting Troubleshooting List..........................................................................75 11. Maintenance Printhead Cleaning............................................................................76 External Cleaning..............................................................................79 Cleaning the Paper Guides ...............................................................80 Printhead Replacement .....................................................................81 12. Adjustments Narrow Labels Adjustment...............................................................84 Label Stop Sensor Position ...............................................................85 Printhead Pressure.............................................................................86 Appendix 1 Technical Data...................................................................................87 Appendix 2 Media Speci cations.........................................................................89 Direct Thermal Labels.................................................................89 Paper Roll Size............................................................................. 90 Intermec EasyCoder F4 Installation & Operation Ed. 2 3 Preface Contents, cont'd. Appendix 2, cont'd. Paper..............................................................................................91

- Non-Adhesive Strip....................................................................91

- Self-Adhesive Strip ....................................................................92

- Self-Adhesive Labels .................................................................93

- Tickets with Gap ........................................................................94

- Tickets with Black Mark............................................................95 Appendix 3 Interfaces............................................................................................96 RS 232C Interface ........................................................................96 USB Interface ...............................................................................97 Double Serial Interface Board (option).......................................98 IEEE 1284 Parallel Interface Board (option) ...........................100 Industrial Interface Board (option)............................................101 EasyLAN 100i Interface Board (option) ..................................102 Appendix 4 EasySet Bar Code Wand Setup ......................................................103 Serial Communication on "uart1:" .............................................104 Start- and Stopadjust....................................................................106 Contrast ........................................................................................107 Test Labels....................................................................................108 Media Width ................................................................................108 Media Length...............................................................................109 Media Type ..................................................................................110 Print Speed...................................................................................110 Paper Type....................................................................................111 Information in this manual is subject to change without prior notice and does not represent a commitment on the part of Intermec Printer AB. Copyright Intermec Printer AB, 2000. All rights reserved. Published in Sweden. EasyCoder, EasyLAN, Fingerprint, and LabelShop are registered trademarks of Intermec Technologies Corp. Centronics is a registered trademark of Centronics Data Computer Corp. Microsoft is a registered trademark of Microsoft Corporation. Torx is a registered trademark of Camcar Division of Textron Inc. TrueDoc is a registered trademark of Bitstream, Inc. TrueType is a trademark of Apple Computer Inc. Unicode is a trademark of Unicode Inc. Windows is a trademark of Microsoft Corporation. 4 Intermec EasyCoder F4 Installation & Operation Ed. 2 Preface FCC Notice (United States of America) WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference when the equip-

ment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. DOC Notice (Canada) Canadian Dept. of Communication REGULATIONS COMPLIANCE (DOC-A) This digital apparatus does not exceed the class A limits for radio noise emissions from a digital apparatus as set out in the radio interference regulations of the Canadian Department of Communication. Ministre des Communications du Canada CONFORMITE DE REGLEMENTS (DOC-A) Le prsent appareil numrique nmet pas de bruits radio-lectriques dpassant les limites applicables aux appareils numriques de classe A prescrites dans le rglement sur brouillage radiolectrique dict par le Ministre des Communications du Canada. GS Notice (Germany) Reparaturen oder sonstige Eingriffe, die sich nicht auf normale Bedienung der Maschine beziehen, drfen ausschlielich nur von einem ausgebildeten, zustndigen Fachmann vorgenommen werden. ALLGEMEINE VORSCHRIFT EU Standard EN 55022 (The European Union) This is a Class A ITE product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING:

Intermec EasyCoder F4 Installation & Operation Ed. 2 5 Preface Declaration of Conformity We, Intermec Printer AB Idrottsvgen 10 S-431 22 Mlndal Box 123 Sweden declare under our sole responsibility1 that the product EasyCoder F4 to which this declaration relates is in conformity with the following standards EMC:

EN 50 081-1:1992 EN 55 022:1994 EN 61 000-3-2:1995, class A EN 50 082-2:1995 EN 61 000-4-2:1995 EN 61 000-4-3:1996 ENV 50 204:1995 EN 61 000-4-4:1995 EN 61 000-4-6:1996 Electrical Safety:

EN 60 950 following the provisions of Directives 89/336/EEC and 73/23/EEC Mlndal 1999-09-01

................................................................... Mats Gunnarsson President 1 /. Intermec assumes no responsibility as regards ful lling the CE Directive if the printer is handled, modi ed or installed in other manners than those described in Intermecs manuals. 6 Intermec EasyCoder F4 Installation & Operation Ed. 2 Introduction Chapter 1 The EasyCoder F4 is a sturdy medium-duty direct thermal printer with a printhead resolution of 8 dots/mm (203.2 dpi) and a maximum print width of 104.0 mm (4.095 inches). It offers a large number of useful facilities, such as.... Flash memory SIMMs for rmware, fonts, bar codes and application programs Built-in memory card adapter Built-in USB and RS 232C interfaces Provision for one extra interface board Bar code wand interface for easy setup Keyboard and display with backlight for improved user interface. The EasyCoder F4 supports the unique and flexible Intermec Fingerprint 7.31 programming language, which allows the user to create custom-made application programs and label layouts in a Basic-like environment. It is also designed to work with the printer drivers for various versions of Microsoft Windows or with the Intermec Direct Protocol programming language. The Windows drivers allows you to design labels using standard PC applications, e.g. Microsoft Of ce. The EasyCoder F4 supports 15 scalable Unicode TrueType and TrueDoc fonts as standard. Additional fonts can be downloaded into the printer's Flash memory, or be plugged in using a memory card. The Unicode standard allows the use of special characters for various languages including non-Latin fonts, such as Cyrillic, Chinese, Japanese, Korean, Hebrew etc. Intermec EasyCoder F4 Installation & Operation Ed. 2 7 Chapter 1 Introduction Safety Requirements Intermec assumes no responsibility as regards ful lling the CE Directive if the printer is handled, modi ed or installed in any way other than that described in Intermec's manuals. Caution Read this manual carefully before connecting the printer. Moving parts are exposed when the side door is open, so ensure that the door is closed before you operate the printer. Do not open the front/left-hand cover. Dangerous voltage!

Do not remove the bottom plate. Dangerous voltage!

Do not put your ngers inside the print mechanism when the power is on. Place the printer on an even surface which can support its weight of approximately 7 kgs (15.5 lbs) plus supplies. Do not spray the printer with water. If using a hose to clean the premises in an industrial environment, remove the printer or protect it carefully from spray and moisture. Carefully read the warning text on the envelope before using a cleaning card. Product Labelling The machine sign is attached to the printer's rear plate and contains information on type, model and serial number as well as mains voltage. It also contains various signs of approval. 8 Intermec EasyCoder F4 Installation & Operation Ed. 2 Print a Label Introduction Chapter 2 Obviously, what you really want to do with your EasyCoder F4 is to print a label, ticket or tag. If you are eager to get started, or if you already are familiar with Intermec's range of EasyCoder printers, follow the instructions in this chapter. If you are new to the EasyCoder concept, bypass this chapter for the time being and read the rest of the manual before returning here. The subject of this chapter is to help you produce a label within minutes from unpacking your printer and to give you an idea of how the Intermec Direct Protocol and the Intermec Fingerprint programming language makes label design an easy task. In addition to the Intermec Direct Protocol and the Intermec Fingerprint programming language, Intermec also includes printer drivers for various versions of Microsoft Windows. After having selected the Windows Driver option in Intermec Shell, you can use the EasyCoder F4 printer the same way as e.g. a laser printer and produce printouts from any standard program in MS Windows. Connecting Printer and Host In the following examples we assume that you use an ASCII terminal or a PC with a terminal program, e.g. Microsoft Terminal and the standard RS 232C interface between the printer and the host. The printer contains a powerful microprocessor which is controlled by means of the Intermec Fingerprint programming language. The connected PC is only used as a non-intelligent terminal for sending instructions to the printer and to display the responses from the printer on a screen. Intermec provides communication cables for connecting the printer to most PC computers. Also refer to Appendix 3 for wiring diagrams. Intermec EasyCoder F4 Installation & Operation Ed. 2 9 Chapter 2 Print a Label Introduction, contd. Setup By default, the printer is set up for the following communication protocol:

Baudrate:

Character length:

Parity:

Stop bits:

Flowcontrol:

New line:

If you want to change any of these values, please refer to chapter 7 Setup Mode. Set up the terminal or host computer for the same communication protocol as the printer. 9600 8 none 1 none CR/LF Paper Supply Load the printer with labels with a width of at least 35 mm (1.4) and a length of at least 40 mm (1.6), see chapter 5. If the printout becomes too light or dark, you will need to change the paper type setup, see chapter 7 Setup Mode. Startup and Communications Check Turn on the printer. Provided the printer is not fitted with any custom-made startup program, after initialization the display will show the Intermec Shell countdown menu:

ENTER=SHELL 5 sec. v.4.4 4 sec. v.4.4 3 sec. v.4.4 2 sec. v.4.4 1 sec. v.4.4 Do not take any action. By default, the display window will show the following message when the countdown is completed, e.g.:

Fingerprint 7.31 If the display does not show this message, refer to chapter 8 Intermec Shell Startup Program and select the Fingerprint application. 10 Intermec EasyCoder F4 Installation & Operation Ed. 2 Introduction, contd. Chapter 2 Print a Label

( = carriage return) Check that the printer and your terminal/PC have a working communication by typing the following instruction on the host:

BEEP The printer should respond by returning Ok to the screen of the host and at the same time emit a short beep. If not, check the communication setup of the printer and the host. The next two steps are included to demonstrate the printers ability both to feed out the paper and to pull it back. Type:

FORMFEED 300 The printer will feed out a short piece of the label. Then order the printer to pull back the label to its original position by typing:

FORMFEED -300 After loading a new supply of labels, the printer should be allowed to adjust itself. Type:

TESTFEED The printer will feed out at least two labels while adjusting its sensors and paper feed mechanism. You can also perform a testfeed operation by simultaneously pressing the < Shift> and <Feed>

keys on the printers keyboard. Tear off the labels by grabbing the outer (right) edge and pulling downwards. Now you are ready to start programming your rst label. Intermec EasyCoder F4 Installation & Operation Ed. 2 11 Chapter 2 Print a Label Intermec Fingerprint Y The label we will design in Intermec Fingerprint will contain a box, an image, a bar code, and a line of text. Note that the illustrations are not reproductions of the label, but are merely intended to show the principles of label editing . Printing a Box Let us start by printing a box 430 dots high and 340 dots wide with a 15 dot line thickness. The box is inserted at position X=10, Y=10:

NEW 10 PRPOS 10, 10 20 PRBOX 430,340,15 200 PRINTFEED 300 END RUN Note: The printer does not execute the program until you have typed RUN . Printing an Image Now we add the image GLOBE.1 after changing the print coordinates to X=30,Y=30. 30 PRPOS 30,30 40 PRIMAGE "GLOBE.1"

RUN D E E F R E P A P X Printing a Bar Code To print a bar code, you need to choose a bar code type before you print the bar code. Note there is no blank space in the bartype name. 50 PRPOS 75,270 60 BARTYPE "CODE39"

70 PRBAR "ABC"

RUN 12 Intermec EasyCoder F4 Installation & Operation Ed. 2 Intermec Finger-

print, cont'd. Chapter 2 Print a Label Printing Human Readables To get human readable text printed under the bar code, add these lines which enables bar code interpretation and selects a font for it:

1 BARFONT ON 2 BARFONT "Swiss 721 BT",6 RUN Printing a Line of Text Add text at position X=25,Y=220:

80 PRPOS 25,220 90 FONT "Swiss 721 BT", 6 100 PRTXT "My FIRST Label"

RUN Listing the Program To view the whole program, type:

LIST The lines will be listed in ascending order on your terminals screen:

1 BARFONT ON 2 BARFONT "Swiss 721 BT", 6 10 PRPOS 10,10 20 PRBOX 430,340,15 30 PRPOS 30,30 40 PRIMAGE "GLOBE.1"

50 PRPOS 75,270 60 BARTYPE "CODE39"

70 PRBAR "ABC"

80 PRPOS 25,220 90 FONT "Swiss 721 BT", 6 100 PRTXT "My FIRST label"

200 PRINTFEED 300 END ok Intermec EasyCoder F4 Installation & Operation Ed. 2 13 Chapter 2 Print a Label Intermec Finger-

print, cont'd. Changing a Program Line If you want to change a program line, simply rewrite the line using the same line number. For example, move the text to the right by rewriting line no. 80 with new coordinates:

80 PRPOS 75,220 RUN Saving the Program If you want to save your rst attempt, issue the following com-

mand. SAVE "LABEL1"

Your program will be saved in the printers permanent memory under the name:

LABEL1.PRG Loading the Program If you want to use this label later, e.g. after having created more programs, type:

LOAD "LABEL1.PRG"

RUN A new copy of the label will be printed. The Intermec Fingerprint offers a lot of more advanced functions that allows you to create sophisticated application programs or to emulate other printer protocols. For more information on the subject of programming, please refer to the documentation of the Intermec Fingerprint programming language. 14 Intermec EasyCoder F4 Installation & Operation Ed. 2 Intermec Direct Protocol Chapter 2 Print a Label The Intermec Direct Protocol can be used in many ways. Here, we will illustrate how to build a layout rst and then provide input data to variable elds in that layout, assuming that you have entered the Intermec Direct Protocol via Intermec Shell (see chapter 8). The nal result will be the same label as created in the example for Intermec Fingerprint. First, create a layout:

LAYOUT INPUT "tmp:LABEL1"

BF ON BF "Swiss 721 BT",6 PP 10,10 PX 430,340,15 PP 30,30 PM "GLOBE.1"

PP 75,270 BT "CODE39"

PB VAR1$

PP 75,220 FT "Swiss 721 BT",6 PT VAR2$

LAYOUT END

(start layut recorder)

(enable bar code interpretation)

(select bar code font)

(insertion point for box eld)

(create a box)

(insertion point for image eld)

(select image)

(insertion point for bar code eld)

(select bar code type)

(variable input data to bar code eld)

(insertion point for text eld)

(select text font)

(variable input data to text eld)

(save layout) Then add the variable data and a print instruction:

LAYOUT RUN tmp:LABEL1

<STX>

ABC My FIRST label

<EOT>

PF

(select layout)

(start of input data, ASCII 02 dec)

(variable input data to VAR1$)

(variable input data to VAR2$)

(end of input data, ASCII 04 dec)

(print one label) Intermec EasyCoder F4 Installation & Operation Ed. 2 15 Chapter 3 Installation Unpacking Before you install the printer, examine the delivery for possible damage or missing parts:

Open the box and lift the printer out. Check that the printer has not been visibly damaged during transportation. Keep the packing materials in case you need to move or reship the printer. The label on the printers rear plate gives the voltage, the part number and the serial number. Check that any options you ordered are included. Check that all the accessories are included in the delivery. In addition to any separately ordered options, the box should contain:

- Intermec EasyCoder F4 printer

- Set of Quick-Load Guides

- Adapter for 3 paper roll core (only in models tted with a rotating paper supply spool)

- Power cord (at least one depending on model)

- Quality check card

- Cleaning card

- Short strip of labels1

- Users Guide (multilingual)

- Installation & Operation manual Check that the power cord is appropriate for the local standard. The printer works within 100 240 V AC, 50 60 Hz. European type 230V mains plug US/Canadian type 115V mains plug GB type 230V mains plug If the printer has been damaged in any way during transportation, complain to the carrier immediately. If the delivery is incorrect or any parts are missing, report it immediately to the distributor. 1/. Type and quantity may vary, or labels may be omitted, depending on area of distribu-

tion. 16 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 3 Installation On the front of the printer are the display window, the control lamps and the keyboard. These features allow the operator to control and set up the printer manually, in addition to the remote control facilities offered by the Intermec Fingerprint rmware and the Intermec Shell startup program. The printed labels, tickets, or tags are fed out through the front of the print unit Front View Control Lamps Display Keyboard Print Key Print Unit Side Door Intermec EasyCoder F4 Installation & Operation Ed. 2 17 Chapter 3 Installation Rear View The rear plate contains the main switch, the power inlet, and various interface connectors:

Bar Code Wand Connector Provision for 1 2 Electronic Keys Optional Interface Board Main Switch Mains Receptacle RS 232C Serial Interface ("uart1:") Memory Card Slot USB Interface

(for future applications) Machine Sign 18 Intermec EasyCoder F4 Installation & Operation Ed. 2 Media Compartment Chapter 3 Installation The media compartment is either covered by a long side door that completely encloses the print mechanism and media compartment, or a short side door that only covers the print mechanism and gives easy access to the paper supply (see chapter 9 Options). Being held by a magnetic lock, the door can be opened 180 so as to provide full access to the media compartment in connection with paper load, ribbon load, and cleaning. The paper supply can be from a hanger, or from an external supply behind the printer. There is also an optional rotating paper supply spool, see chapter 9 Options. Paper Hanger Print Mechanism Long Side Door Optional rewind unit with guide shaft Intermec EasyCoder F4 Installation & Operation Ed. 2 19 Chapter 3 Installation Media Compart-

ment, cont'd. Being of a modular design for maximum exibility, the EasyCoder F4 can use a paper supply hanger tted in three different positions inside the media compartment, depending on the type of side door

(long or short) and whether the printer is tted with a rewind unit for the backing paper (liner) or not. Alternatively, an external paper supply (e.g. a box of fan-folded tickets) behind the printer can be used. A rotating paper supply spool is also available as an option

(see chapter 9 Options). Paper Supply Hanger The paper supply hanger ts both 38 40 mm (1.5") and 76 mm (3") cores since it can be moved vertically in the slot in centre section. The lowermost position is intended for small cores and the uppermost one for large cores only. The hanger is locked by a screw and has a moveable guide to t various paper widths. Guide 76 mm

(3 inches) CORE 38 - 40 mm

(1.5 inch) Screw (hidden) To remove the hanger, remove the screw, twist the hanger a quarter of a turn and pull it out. To t the hanger into a slot in the centre section (see next page), rotate it a quarter of a turn and twist back so the lips engage the cut-outs in the sides of the slot. Move it up (3" core) or down (1.5"

core) as far as it goes and secure it with the screw. Warning:

Make sure to t the hanger according to the size of the paper roll core. When the hanger is tted in its upper position, the screw will interfere with any small (38 mm/1.5") core causing paper misalignment. 20 Intermec EasyCoder F4 Installation & Operation Ed. 2 Media Compart-

ment, cont'd. Chapter 3 Installation Paper Supply Positions There are four sets of threaded holes and slots in the printer's centre section for the paper supply hanger (or spool) so as to allow the largest possible roll size, given the limitations of the rewind unit and/or the full enclosure provided by the long side door. The positions are indicated by numbers engraved in the centre section. Position 1 is used when the paper compartment is fully enclosed by a long side door, regardless of the existence of a rewinder Maximum roll size is 152 mm (6"). Position 2 is used in connection with a short side door that only encloses the print unit, but without any rewinder. Maximum roll size is 213 mm (8.38"). Position 3 is used in connection with a short side door and an optional rewind unit. Maximum roll size is 203 mm (8"). Position 4 is reserved for future development. The printer can also use an external paper supply located behind the paper compartment. 2 1 3 4 Pos. 3 Pos. 2 Pos. 1

(Pos. 4) Intermec EasyCoder F4 Installation & Operation Ed. 2 21 Chapter 3 Installation Print Mechanism The print mechanism features a high-performance 8 dots/mm

(200 dpi) thermal printhead with quick-mount ttings to facilitate replacement. Thermal Printhead Tear Off Edge Platen Roller Pressure Arm Printhead Lift Knob Paper Guide 22 Intermec EasyCoder F4 Installation & Operation Ed. 2 Connections Power Computer Chapter 3 Installation 1 Place the printer on a level surface, near a mains electrical outlet and with easy access for loading paper and for removing printout. 2 Check that the printer is switched off. 3 Connect the power cable to the mains receptacle on the rear plate and to the electrical outlet. The Easycoder F4 is tted with one DB25 female connector for the RS 232 serial interface port and one class B connector for the USB port (see Appendix 3). RS 232 Serial Interface Use the serial interface with Direct Protocol or Intermec Fingerprint programming because you can receive error messages from your printer. Before you can use the serial interface, you may need to set up the communication parameters, such as baudrate, parity etc. as described in chapter 6 Setting Up the Printer. USB Interface The USB interface is intended for future applications. Optional Interface Board Refer to Appendix 3 and the separate documentation delivered with the boards for connection and setup instructions. Switch off both the PC and the printer before connecting them together. Intermec EasyCoder F4 Installation & Operation Ed. 2 23 Chapter 3 Installation Controls and Indicators The EasyCoder F4 has several ways of communicating directly with its operator; three control lamps, a display window, a membrane-

switch keyboard with 22 programmable keys, a big programmable Print button on the printer's front, and a beeper. Control Lamps Display Keyboard The control lamps are coloured LEDs (Light Emitting Diodes) and are used for the following purposes:

Power (green) indicates when the power is on. Ready (green) indicates when the printer is ready for use. Error (red) indicates when some kind of error has occurred. If using a serial communication, an error message may be returned to the host computer. The display window contains an LCD (Liquid Crystal Display) with background illumination and 2 lines of text, each with 16 characters. It guides the operator through the setup and informs him or her of possible errors during printing. The Intermec Fingerprint programming language and the Intermec Direct Protocol allows custom-made messages to be composed and displayed according to the requirements of the application. The keyboard is of membrane switch type and has 22 keys. The keyboard is supplemented by a large Print button on the printer's front. Some keys have hardcoded functions in the startup and setup modes. In application programs created by means of the Intermec Fingerprint programming language, the keys can be assigned to various functions according to requirements. As one key is assigned as shift key, up to 44 different key combinations are possible. An audible signal, which can be turned off if so desired, acknowledges that a key has been pressed. 24 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 3 Installation Controls and Indicators, cont'd. Beeper The beeper noti es the operator when an error has occurred and acknowledges that a key has been pressed. The Intermec Fingerprint programming language allows the key acknowledge signal to be turned off. The frequency and duration of the signal can be speci ed at will. Thus, it is possible create different signals for different conditions or even to make the printer play simple melodies!

Intermec EasyCoder F4 Installation & Operation Ed. 2 25 Chapter 4 Starting Up Startup Files At startup, the behaviour of the printer is decided by the possible existence of a startup le (autoexec.bat) somewhere in the printer's memory, i.e. a program that automatically starts running when the printer is turned on. There are two cases:

A The printer is only tted with the Intermec Shell le-managing program, which allows the operator to choose between a variety of applications and functions. B In addition to Intermec Shell, the printer is also tted with a custom-made application program that is design to perform a speci c task, e.g. to print tickets, baggage tags, or product labels for a certain company: Such a program may be initiated by a startup le (autoexec.bat) stored in the printer's permanent memory or in a memory card. There can be one startup le stored in each of three different parts of the printer's memory. If there are startup les stored in more than one place, they will be used with the following priority:

1. An autoexec.bat le stored in any approved type of memory card, provided it was inserted in the printer before power up. 2. An autoexec.bat le stored in the user's part of the printer's permanent memory (device "c:"). 3. The pup.bat le (Intermec Shell) in the systems part of the printer's permanent memory (device "rom:"). Electronic Keys This implies that if you insert a memory card with startup le before you turn on the printer, the startup le of the memory card will be used instead of Intermec Shell. Some applications may require one or two electronic keys to be inserted in the slot in the guide plate. Remove the plastic cover and insert the key so the at side faces the centre of the slot. It does not matter if the key is tted in the right or left position. In case of two electronic keys, the flat sides should face each other. Important!

Always turn off the power before inserting or removing an electronic key. 26 Intermec EasyCoder F4 Installation & Operation Ed. 2 Memory Card Chapter 4 Starting Up If you want to use a memory card, you must insert it into the slot in the printer's rear plate before you turn on the power. The memory card can be an SRAM card complying with the JEIDA-4 standard or Flash Memory card from Intermec. Maximum size in both cases is 64 Mbit (8 MB). There are three types of Flash Memory Cards:

A Font Card provides additional fonts as long as it remains inserted in the printer. A Font Install Card permanently installs additional fonts in the printer which can be used even after the card has been removed. A Firmware Card automatically replaces the printer's rmware, e.g. with an updated version. Power On Memory Card Backside Important!

Always turn off the power before inserting or removing a memory card!

Do not start the printer before you have made the necessary connections, inserted any memory card you want to use, and checked that the printhead is lowered. Turn on the power by means of the main switch on the rear plate. The Power LED control lamp on the front panel lights up when the power is on. Wait for a few moments, while the printer loads the program and runs some self-diagnostic tests. Then some kind of message will appear in the display window, depending on startup le. Intermec EasyCoder F4 Installation & Operation Ed. 2 27 Chapter 4 Starting Up Display Messages at Startup When the power is turned on, the printer is initialized. The progress of the initialization is indicated by an increasing number of dots on the lower line in the display:

Initializing

The type of startup le running in the printer is indicated by the message shown in the display window directly after initialization. A. Intermec Shell Startup Program (standard printers) ENTER=SHELL 5 sec. v.4.4 4 sec. v.4.4 3 sec. v.4.4 2 sec. v.4.4 1 sec. v.4.4 Refer to chapter 8 for further information on Intermec Shell. The digits in the lower right corner of the display indicate the version of Intermec Shell. B. Custom-made Application Program (non-standard printers) Any other display message than those illustrated above indicates that the printer is running some custom-made, non-standard application program or that some error has occurred. 28 Intermec EasyCoder F4 Installation & Operation Ed. 2 Paper Load Tear-Off Chapter 5 The EasyCoder F4 can print on labels, tickets, tags, and paper strip in various forms. This chapter describes the case when the paper strip is to be torn off manually against the printer's tear-off edge. Use the <Feed> key (see gure #10) when loading the same type of paper as before. When switching to a new type of media or when the printer does not feed out the paper properly, simultaneously press the < Shift> and <Feed> keys. Tear-off can be used for:

Non-adhesive continuous paper strip Self-adhesive continuous paper strip Self-adhesive labels on backing paper Tickets with gaps, with or without perforations Tickets with marks, with or without perforations 1 2 Open the side door. Turn the printhead lift knob clockwise to lift the printhead. Intermec EasyCoder F4 Installation & Operation Ed. 2 29 Chapter 5 Paper Load Tear-Off, cont'd. 3 4 2 1 3 4 2 1 3 4 Remove any empty paper core from the paper supply hanger. Hook a new roll of labels, tickets, tags, or strip on the paper supply hanger and adjust the guide so the paper roll comes in ush with the wall. 5 6 Thread the paper through the print mechanism and push it inwards as far as it will go. This diagram shows the path of the paper web. 30 Intermec EasyCoder F4 Installation & Operation Ed. 2 Tear-Off, cont'd. 7 8 Chapter 5 Paper Load Turn the printhead lift knob counter-clockwise to lower the printhead Adjust the position of the green paper guide so the paper is guided with a minimum of play. 9 10 Close the side door. Intermec EasyCoder F4 Installation & Operation Ed. 2 Adjust the paper feed by pressing the Feed key. 31 Chapter 5 Paper Load Tear-Off, cont'd. 11 To tear off the paper, grab the outer edge and pull downwards. 32 Intermec EasyCoder F4 Installation & Operation Ed. 2 Tear-Off with Quick-Load Chapter 5 Paper Load In addition the paper load procedure for tear-off operation described earlier in this chapter, the EasyCoder F4 can optionally be tted with a set of Quick-Load paper guides that makes paper load much easier and quicker, especially in connection with a short side door. See chapter 9 Options for installation instructions. Quick-Load is usually not used in connection with a long side door and cannot be combined with peel-off operation. Use the <Feed> key (see gure #5) when loading the same type of paper as before. When switching to a new type of media or when the printer does not feed out the paper properly, simultaneously press the < Shift> and <Feed> keys. Important!

Full automatic loading without the operator having to press any key requires a special set of Intermec Fingerprint instructions in the application program. 1 2 Remove any empty paper core from the paper supply hanger. Hook a new roll of labels, tickets, tags, or strip on the paper supply hanger and adjust the guide so the paper roll comes in ush with the wall. Intermec EasyCoder F4 Installation & Operation Ed. 2 33 Chapter 5 Paper Load Tear-Off with Quick-Load, cont'd. 3 4 In necessary, adjust the outer guide to t the width of the paper. Insert the paper between the guides and feed it forward until the paper reaches the platen roller and cannot be inserted any further. 5 6 Keep pushing the paper forward while pressing the Feed key. To tear off the paper, grab the outer edge and pull downwards. 34 Intermec EasyCoder F4 Installation & Operation Ed. 2 Peel-Off Chapter 5 Paper Load The EasyCoder F4 can print on labels, tickets, tags, and paper strip in various forms. This chapter describes the case when self-adhesive labels are separated from a backing paper (liner) immediately after printing after which the backing paper is rewound internally in the printer. Peel-off operation cannot be performed when quick-load guides are tted. Use the <Feed> key (see gure #13) when loading the same type of paper as before. When switching to a new type of media or when the printer does not feed out the paper properly, simultaneously press the < Shift> and <Feed> keys. Peel-off can only be used for:

Self-adhesive labels on backing paper An optional label-taken sensor can hold the printing of next label in a batch until the present label has been removed, see chapter 9 Options. 1 2 Open the side door. Turn the printhead lift knob clockwise to lift the printhead. Intermec EasyCoder F4 Installation & Operation Ed. 2 35 Chapter 5 Paper Load Peel-Off, cont'd. 3 4 2 1 3 4 Pull out the handle to collapse the rewinder, Remove any empty paper core from the paper then remove the backing paper. supply hanger. 5 2 1 3 4 6 Hook a new roll of labels on the paper supply hanger and adjust the guide so the label roll of the web. Thread the backing paper through the print mechanism and push it inwards as far comes in ush with the wall. as it will go. Remove labels from the rst 50 cm (20") 36 Intermec EasyCoder F4 Installation & Operation Ed. 2

 

 

Peel-Off, cont'd. 7 8 Chapter 5 Paper Load Thread the backing paper around the tear-off edge and back under the print mechanism and Insert the end of the backing paper under the lip of the rewinder, then rotate the rewinder guide shaft. counter-clockwise a few turns. 9 10 This diagram shows the path of the label web. to lower the printhead Turn the printhead lift knob counter-clockwise Intermec EasyCoder F4 Installation & Operation Ed. 2 37 Chapter 5 Paper Load Peel-Off, cont'd. 11 12 Adjust the position of the green paper guide so the paper is guided with a minimum of play. Close the side door. 13 Adjust the paper feed by pressing the Feed key. 38 Intermec EasyCoder F4 Installation & Operation Ed. 2 External Supply Chapter 5 Paper Load The EasyCoder F4 can print on labels, tickets, tags, and paper strip in various forms. This chapter describes the case the paper supply is placed behind the printer, usually in the form of fan-folded tickets and tags. External supply can be used in connection with tear-off operation preferably with Quick-Load. External supply can be used with both short and long side doors and there is no need to remove the paper roll hanger. When using an external paper supply, take care to protect the paper from dust, dirt or other foreign particles, that can impair the printout quality or cause unnecessary wear to the printhead. Direct thermal paper is more or less sensitive to heat, direct sunlight, moisture, oil, plasticizers, fat, and other substances, depending on brand and quality and should be protected accordingly. 1 This diagram shows the path of the paper web from an external supply. In case of the standard paper guide ring, it is recommended to turn it to vertical position for better guiding of the web. Intermec EasyCoder F4 Installation & Operation Ed. 2 39 Chapter 6 Setting Up the Printer Description The setup is used to control the printer in regard of serial com-

munication, paper feed and print speed, and to specify which type of paper is loaded in the printer. Check the list of default setup values below to see if the printer's setup matches your requirements. If not, you will have to change the setup, which can be done manually via the printer's built-in keyboard, remotely from the host computer, or by reading a bar code containing setup data with the optional EasySet bar code wand. The setup may also be changed, partially or completely, by certain application programs. In the Setup Mode:

- Press the <Setup> key on the printer's built-in keyboard

- Select the Setup option in Intermec Shell to enter the

- Execute the Intermec Fingerprint SETUP instruction to to enter the Setup Mode. Setup Mode. enter the Setup Mode. See chapter 7 Setup Mode in this manual. In Intermec Shell:

- Use Terminal Setup option to change the setup remotely from the host. Note that Intermec Shell automatically sets up the printer in regard of communication when an application is selected. See chapter 8 Intermec Shell in this manual. In Intermec Fingerprint:

- Use Setup strings to change individual setup parameters remotely from the host.

- Use Setup les to create sets of setup parameters remotely See SETUP statement in the Intermec Fingerprint 7.xx Reference from the host. Manual. In the Intermec Direct Protocol:

- Use Setup strings to change individual setup parameters remotely from the host. See Intermec Direct Protocol 7.xx Programmer's Guide. Using the EasySet Bar Code Wand:

- Read a Code 128 bar code containing the setup parameter id. and the desired value or choice. See Appendix 4. 40 Intermec EasyCoder F4 Installation & Operation Ed. 2 Default Setup The printer is by default set up according to the list below:

Chapter 6 Setting Up the Printer Ser-Com "uart1:"

Baudrate:

Character length:

Parity:

Stop bits:

RTS/CTS:

ENQ/ACK:

XON/XOFF, data to host:

XON/XOFF, data from host:

New line:

Receive buffer:

Transmit buffer:

Feedadjust:

Startadjust:

Stopadjust:

Media:

X-start:

Width:

Length:

Media Type:

Label Constant:

Label Factor:

Contrast:

Print De nes:

Print speed:

9600 bps 8 bits None 1 bit Disable Disable Disable Disable CR/LF 300 bytes 300 bytes 0 0 24 832 1200 Label (w Gaps) 85 40 0%

100 mm/sec. The printer's current setup values can be read from the display by browsing through the Setup Mode, or from the host by browsing through the Terminal Setup of Intermec Shell. You can list the printer's current setup values by printing test label

#5 in the Setup Mode or using Intermec Shell. The current setup values can be returned to the host by means of a SETUP WRITE "uart1:" statement (see Intermec Fingerprint 7.xx Reference Manual). Intermec EasyCoder F4 Installation & Operation Ed. 2 41 Chapter 6 Setting Up the Printer Setup Parameters Serial Communication

Baudrate

Character Length

Parity

Stop Bits

Flow Control

New Line

Receive Buffer

Transmit Buffer The serial communication setup controls the communication between the printer and the connected computer or other devices on the standard serial channel "uart1:" and the optional serial channels "uart2:" and "uart3:". The latter channels require an optional interface board to be tted. The printer's rmware detects if an optional interface board is tted and presents additional sets of communication setup menus depending on type of communication

(refer to diagrams #3 5 in chapter 7 Setup Mode). The serial communication setup has no consequence whatsoever for parallel communication or for the IN and OUT ports on the optional Industrial Interface Board. For the serial communication channel "uart1", the following parameters can be set. Make sure they match the setup of the connected device or vice versa. If the setup of the printer and the setup of the host do not match, the response from the printer to host will be garbled. Baudrate The baudrate is the transmission speed in bits per second. There are 10 options:

300 600 1200 2400 4800 9600 (default) 19200 38400 57600 115200 42 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Parameters, cont'd. Chapter 6 Setting Up the Printer Serial Communication, cont'd. Character Length The character length speci es the number of bits in a character. For most purposes 7 bits will be suf cient, but if special characters or characters speci c for other languages are to be used, 8 bits are recommended. Refer to the Intermec Fingerprint 7.xx Reference Manual for information on which characters are available in various combinations of character length and character set. 7 8 Characters ASCII 0 127 decimal Characters ASCII 0 255 decimal

(default) Parity The parity decides how the rmware will check for transmission errors. There are ve options:

None (default) Even Odd Mark Space Stop Bits The number of stop bits speci es how many bits will de ne the end of a character. There are two options:

1 2

(default) Flow Control RTS/CTS RTS/CTS is a protocol where the communication is controlled by currents through separate lines in the cable being set either to high or low. By default, this option is disabled. RTS high indicates that the transmitting unit is able to receive characters. RTS low indicates that the receive buffer is lled to 75% (see XON/XOFF). CTS high indicates that the unit transmitting the CTS signal is ready to receive data. CTS low indicates that the receive buffer is full (see XON/XOFF). In some computer programs, e.g. MS Windows Terminal, RTS/CTS is designated Hardware.'

Intermec EasyCoder F4 Installation & Operation Ed. 2 43 Chapter 6 Setting Up the Printer Setup Parameters, cont'd. Serial Communication, cont'd. ENQ/ACK In this protocol, the communication is controlled by the special characters ENQ (ASCII 05 dec.) and ACK (ASCII 06 dec.) being transmitted on the same line as the data. The sending unit transmits ENQ at regular intervals. If the response ACK is not received the transmission is held up awaiting an ACK character from the receiving unit. By default, ENQ/ACK is disabled. XON/XOFF In this protocol, the communication is controlled by the special characters XON (ASCII 17 dec.) and XOFF (ASCII 19 dec.) being transmitted on the same line as the data. XON/XOFF can be enabled/disabled separately for data received from the host by the printer (printer sends XON/XOFF), and for data transmitted to the host from the printer (host sends XON/XOFF). XOFF is sent from the printer when its receive buffer is lled by 75%, and the transmission from the host is held up awaiting an XON character. When enough data have been processed that the receive buffer is lled only to 50%, the printer sends an XON character and the host resumes transmitting data. The same principles apply to XON/XOFF sent by the host, even if the percentage may differ. By default, XON/XOFF is disabled for data both ways. New Line Selects the character(s) transmitted from the printer to specify the switching to a new line. There are three options:

CR/LF LF CR ASCII 13 dec. + ASCII 10 dec. ASCII 10 dec. ASCII 13 dec.

(default) Receive Buffer The receive buffer stores the input data received on the serial channel before processing. Default size is 300 bytes. Transmit Buffer The transmit buffer stores the output data received on the serial channel before transmission. Default size is 300 bytes. 44 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Parameters, cont'd. Chapter 6 Setting Up the Printer Net Communication

New Line Feedadjust

Startadjust

Stopadjust Recommended Feed Adjustments The following settings allow printing from the top of the label. Minor deviations from the recommended values may be required due to various com-

binations of media types, roll size, type of media supply device, and individual differences bet-

ween printers. Tear-Off:

Start adjust: -100 (-12.5 mm) Stop adjust: 0 (0 mm) Peel-Off:

Start adjust: -56 (-7.0 mm) Stop adjust: -44 (-5.5 mm) New Line Only shown if an optional EasyLAN 100i interface board is tted and used to select the character(s) transmitted from the printer, to specify the switching to a new line. There are three options:

ASCII 13 dec. + ASCII 10 dec. CR/LF ASCII 10 dec. LF CR ASCII 13 dec.

(default) The Feedadjust part of the Setup Mode is used to feed out or pull back the paper before and/or after the actual printing. These settings are global and will be effected regardless of which program is run. Note that the rmware uses the front edges of labels w. gaps, the ends of detection slots and the forward edges of black marks for detection, all seen in relation to the paper feed direction. Start Adjust The Start Adjust value is given as a positive or negative number of dots (1 dot = 0.125 mm = 4.9 mils). Default value is 0, which places the origin a certain distance back from the forward edge of the copy. A positive start adjustment means that the speci ed length of paper web will be fed out before the printing starts, i.e. the origin is moved further back from the forward edge of the copy. A negative start adjustment means that the speci ed length of paper web will be pulled back before the printing starts, i.e. the origin is moved towards the forward edge of the copy. Stop Adjust The Stop Adjust value is given as a positive or negative number of dots (1 dot = 0.125 mm = 4.9 mils). Default value is 0, which stops the paper feed in a position suitable for tear off operation. A positive stop adjustment means that the normal paper feed after the printing is completed will be increased by the speci ed value. A negative stop adjustment means that the normal paper feed after the printing is completed will be decreased by the speci ed value. Intermec EasyCoder F4 Installation & Operation Ed. 2 45 Chapter 6 Setting Up the Printer Setup Parameters, cont'd. Media

Media Size

Media Type

Paper Type

Testfeed

Contrast The media setup tells the rmware the characteristics of the of media that will be used, so the printout will be positioned correctly on the paper and get the best quality possible. Media Size The size of the printable area is de ned by three parameters; X-Start, Width, and Length. X-Start X-start speci es the position of the origin along the dots on the printhead. By default, X-start is 24 dots, which places the inner margin of the print area 3 mm (0.118") from the inner edge of the paper and gives a maximum print width of 808 dots (101 mm/3.976"). If you want to make use of the entire paper width, reset the X-start value to 0 which gives a maximum print width of 832 dots (104 mm/4.095"). By increasing the value for the X-start parameter, the origin will be moved outwards, away from the inner edge of the web. In other words, the larger X-start value the wider inner margin and the less available print width. Width Width speci es the width of the printable area and is de ned as a number of dots from the origin. The sum of the X-start value and the width value gives the outer margin of the printable area. The width must not be so large as to allow printing outside the paper web and must not exceed 832. Length Length decides the length of the printable area from origin and along the Y-coordinate as a number of dots by allocating memory space in the printer's temporary memory. Two identical image buffers are created. The size of each buffer can be calculated using this formula:

Buffer size (bits) = [Print length in dots] x [Printhead width in dots]

Note that the temporary memory has other functions that also require some memory space. To obtain a longer print area, the memory can be increased by tting a larger DRAM SIMM on the printer's CPU board as described in the Service Manual. 46 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Parameters, cont'd. Chapter 6 Setting Up the Printer Media, cont'd. Length, cont'd. The length setup also decides the amount of paper feed when using x length strip. The length setup creates an emergency stop, which works when the printer is set up for Label (w gaps), Ticket (w mark), or Ticket (w gaps). If the LSS has not detected a gap or mark within 150% of the set length, the paper feed is automatically stopped to avoid feeding out a whole roll of paper, because of e.g. a blocked or faulty LSS. By setting up the X-start, the Width and the Length, you will create a print window inside which the printing can be performed. Any object or eld protruding outside the print window in any direction will cause an error condition (Error 1003 Field out of label). 10.3 mm (0.41") max. 104.0 mm (4.095") Length PRINT PRINT WINDOW WINDOW Origin Dot-line on printhead X-start Width (1832) Dot #0 PAPER FEED DIRECTION Dot #831 25 114.3 mm (1 4.5") Intermec EasyCoder F4 Installation & Operation Ed. 2 47 Chapter 6 Setting Up the Printer Setup Parameters, cont'd. Media, cont'd. Media Type The Media Type setup controls how the LSS and the paper feed work. There are ve different media types:

Label (w gaps) is used for adhesive labels mounted on backing paper. Ticket (w mark) is used for labels, tickets, or strip provided with black marks at the back of the paper web. Ticket (w gaps) is used for tickets and tags with detection slits. Fix length strip means that the length of the print window decides the length of strip to be fed out. Var length strip adds 115 dots of paper feed after the last printable dot (may even be a blank space character or a white dot in an image or character cell) to allow the strip to be properly torn off. It is important to select the type, so the printer can indicate possible paper errors. Two different error conditions may occur:

Error 1005 Out of paper indicates that the last ordered copy could not be printed because of an empty paper stock. Error 1031 Next label not found indicates that the last ordered label or ticket was successfully printed, but no more labels/tickets can be printed because of an empty paper stock. Paper Type The Paper Type setup controls the heat emitted from the printhead to the transfer ribbon or direct thermal paper in order to produce the dots that make up the printout image. Two parameters must be set:

Label Constant Label Factor See the list on next page for recommended settings for various types of standard Intermec direct thermal media.

(range 50 115)

(range 10 50) 48 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Parameters, cont'd. Chapter 6 Setting Up the Printer Media, cont'd. Recommended Settings Intermec recommends the paper type and print speed settings listed below to produce the highest possible print quality under normal conditions and to ensure maximum lifetime of the printhead. Use the EasySet bar code wand for easy media setup. Label materials are available from Intermec either in standardized types and sizes, or in special materials and sizes on request. When adjusting the image darkness for individual requirements or new label materials, proceed as follows:

Keep the Label Factor at the recommended value for the type of direct thermal paper. Then decrease or increase the Label Constant for lighter or darker images respectively, depending on the requirements of the images or of the new label material. General Paper Type Settings Guide Sensitivity1 Label Constant Label Factor Max. Speed3 Low 100 115 40 100 Standard 86 99 40 125 High 70 85 40 175 Ultra high 50 69 40 200 Direct Thermal Papers (Europe) DT Type/ Paper Label Label Max Rec. Print Speed (mm/sec)3 Speed Designation Constant Factor Picket Fence Bar Code Ladder Bar Code Top Coated/ Top Board2 100 40 100 100 Standard Premium 95 40 125 125 Non Top Coated/ Economy 85 40 125 125 Standard Eco Board2 80 40 175 175 Top Coated/High Premium High Speed 85 40 175 175 Direct Thermal Papers (North America) DT Type/ Paper Label Label Max Rec. Print Speed (mm/sec)3 Speed Designation Constant Factor Picket Fence Bar Code Ladder Bar Code Top Coated/ Duratherm II Tag2 112 40 100 100 Standard Duratherm II 95 40 100 100 Top Coated/ Duratherm Ltg 92 40 175 175 High Duratherm IR 82 40 150 150 1/. Please note that preprint and varnish decrease the sensitivity of the direct thermal paper. 2/. May require increased printhead pressure (see chapter 12 Adjustments; Printhead Pressure). 3/. Exceeding the recommended print speed may, even in case of plain text printing, cause premature wear-out of the printhead Intermec EasyCoder F4 Installation & Operation Ed. 2 49 Chapter 6 Setting Up the Printer Setup Parameters, cont'd. Media, cont'd. Print De nes

Head Resistance

Testprint

Print Speed

LTS (optional) Contrast The contrast setup is used to make minor adjustments of the blackness in the printout, e.g. to adapt the printer to variations in quality between different batches of the same paper quality. 11 options are displayed in an endless loop from -10% to +10%. Default value is 0%. The contrast is reset to default (0) whenever a new paper type is speci ed, regardless which method has been used. Testfeed The sensitivity of the label stop sensor (LSS) may need to be adjusted, e.g. when switching from one type of media to another. This is especially the case when using self-adhesive labels tted on a semi-transparent backing paper (liner). Adjusting the LSS entails feeding out a number of blank copies until the rmware has decided the proper setting for the LSS. At the same time, the front edges of the labels, tickets etc. are detected so the paper feed control can position the paper according to the Feedadjust setup (same as the Intermec Fingerprint statement TESTFEED). The comparator and ampli er values of the LSS are displayed (read-only). Head Resistance The printhead resistance is measured automatically at startup and displayed (read-only). Testprint Test label #1 4 are intended for checking the printout quality and facilitate adjustment of the printhead pressure (see chapter 13Adjustments). Test label #5 lists the printer's current setup

(extra labels may be printed if the printer is fitted an optional interface board). Test label #6 is only printed in connection with the optional EasyLAN 100i interface board. The test labels #1 5 are illustrated on next page. If the printer refuses to print a test label, press the <F3> key to nd out what is wrong, e.g. printhead lifted or out-of paper. 50 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Parameters, cont'd. Print De nes, cont'd. Chapter 6 Setting Up the Printer 681 ohms/8 dots Test Label #1 Test Label #2 Test Label #3 Test Label #4 1

N

8

0 0 6 9 E L B A S D I E L B A S D I E L B A S D I E L B A S D I

F L R C 0 0 3 0 0 3 8 0 8 4 2 0 0 8 1 0 0

) S P A G w

L E B A L L A M R E H T T C E R D I

0

3 2 1 5 8 0 4 1 8 6 0 0 1 4 F 0

. 3 0 T S O H M O R F A T A D T S O H O T A T A D S T C S T R

K C A Q N E 1 T R A U F F O X N O X

I G F N O C T N R P I F U B S N A R T F U B C E R J D A T R A T S J D A P O T S T R A T S X H T D W I H T G N E L I E N L W E N T N A T S N O C L E B A L R O T C A F L E B A L E P Y T R E P A P T S A R T N O C D E E F T S E T E P Y T A D E M I I T S S E R D A E H i n o s r e v e r a w d r a H

) k

6 9 0 4 m a R

t m k

r e e m o d O l e d o M D E E P S T N R P I

) k

6 1 0 1

8 4 0 2

0 h s a F l e e r f s e t y b 4 0 5 9 1 8 1

c

) k

0 l a n r e t x E E R A W M R F I

0

5 2

9 0

7 1 7 9

Y A M

7 2 2 8 7 0 v a s l k 3 m x x

x x

x x 0 0

x x

x x 7 4 1 1 S C M 1 3

. 7 t n i r p r e g n F i

1

l e v a s d r a o b y e k o N Test Label #5 Intermec EasyCoder F4 Installation & Operation Ed. 2 51 Chapter 6 Setting Up the Printer Setup Parameters, cont'd. Print De nes, cont'd. Network

IP Selection

IP Address

Netmask

Default router Print Speed The print speed is variable between 100 and 200 mm/sec. Generally, the lower the speed, the better the printout quality. This is especially the case when printing bar codes with the bars running across the paper web (ladder style), when printing on demanding face materials, and when printing at low ambient temperatures. Refer to the tables under Media earlier in this chapter for maximum print speed values. The default setting is 100 mm/sec. LTS (Label-Taken Sensor) The sensitivity of the LTS may need to be adjusted according to ambient light conditions and re ective characteristics of the back side of the paper. The LTS setup options are only displayed if an optional label-taken sensor is installed in the printer.

LTS Adjust:

Press <Enter>. A label is feed out. Remove the label and press

<Enter> again. A menu shows the sensitivity automatically selected by the rmware and the range, in which the LTS will work. Press <Enter> again and you will proceed to the LTS Test menu.

LTS Test:

Press <Enter>. A label is fed out. Remove the label and a new label should be fed out automatically. Repeat until you are sure the LTS works properly. Then press <Enter> to stop and exit. LTS Value:

Press <Enter>. You can enter a new value in the range indicated in the LTS Adjust menu (see above). Min/max values are in the range 010. If an optional EasyLAN 100i interface board is tted, a number of additional setup menus will be displayed. These menus are used for setting up the IP address, the netmask, and the default router for the EasyLAN 100i board, as described in separate manuals delivered with the board. 52 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Mode Entering Setup Mode at Installation Chapter 7 The method of entering the Setup Mode depends on whether the printer is tted with some kind of startup le, a subject that was more thoroughly discussed in the chapter 4 Starting Up earlier in this manual, to which the alphabetic references below refer. A. EasyCoder F4 with Intermec Shell Turn on the power. When the display shows the message Enter=Shell; x sec., Press the <Setup> key (this facility can be used anywhere press <Enter>. within Intermec Shell). Set up the printer as described in this chapter. Return to Intermec Shell by pressing the < Setup> key. B. EasyCoder F4 with a custom-made application program Normally, there will be no need to enter the Setup Mode for custom-made application programs. Necessary provisions for changing the setup, manually or automatically, should be provided by the program. Intermec EasyCoder F4 Installation & Operation Ed. 2 53 Chapter 7 Setup Mode Navigating in Setup Mode While going through the setup procedure, you are guided by texts in the printer's display. You can step between setup menus, acknowledge displayed values, select or type new values etc. by means of some of the keys on the printer's keyboard. Note!

An external keyboard cannot be used inside the Setup Mode. Move one menu to the left on the same level1. Move one menu to the right on the same level1. Display error message at test labels printing failure. Move up one level or scroll back in a stack of options1. Move down one level or scroll forward in a stack of options1.

Enter numeric values. Specify negative values (leading position) Clear erroneously entered values. Acknowledge and move to next menu. Perform testfeeds in the Testfeed menu. Print test labels in the Test Label menu. Exit the Setup Mode.

(Can be used anywhere in the Setup Mode.) 1/. Left, right, up, and down refer to the diagrams on the following pages. 54 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 7 Setup Mode LEGEND:

Boxes with thick lines indicate default setup Boxes with dotted lines indicate menus related to optional interface boards. RTS/CTS:

DISABLE ENABLE ENQ/ACK:

DISABLE ENABLE XON/XOFF:

DATA TO HOST XON/XOFF:

DATA FROM HOST DATA TO HOST:

DISABLE ENABLE DATA FROM HOST:

DISABLE ENABLE Setup Mode Overview, Part 1

(Intermec Fingerprint 7.31) SETUP:

SER-COM,UART1 SETUP:

SER-COM,UART2 SETUP:

SER-COM,UART3 SETUP:

NET-COM,NET1 SER-COM,UART1:

BAUDRATE See Overview Part 3 See Overview Part 4 See Overview Part 5 SER-COM,UART1:

CHAR LENGTH SER-COM,UART1:

PARITY SER-COM,UART1:

STOP BITS BAUDRATE:

9600 19200 38400 57600 115200 300 600 1200 2400 4800 CHAR LENGTH:

8 7 PARITY:

NONE EVEN ODD MARK SPACE STOPBITS:

1 2 SER-COM,UART1:

FLOWCONTROL FLOWCONTROL:

RTS/CTS FLOWCONTROL:

ENQ/ACK FLOWCONTROL:

XON/XOFF NEW LINE:

CR/LF LF CR REC BUF:

[300]:

TRANS BUF:

[300]:

STARTADJ:

[0]:

STOPADJ:

[0]:

SER-COM,UART1:

NEW LINE SER-COM,UART1:

REC BUF SER-COM,UART1:

TRANS BUF FEEDADJ:

STARTADJ FEEDADJ:

STOPADJ DETECTION:

SETUP:

FEEDADJ FEEDADJ Continued on next page!

Intermec EasyCoder F4 Installation & Operation Ed. 2 55 Chapter 7 Setup Mode Setup Mode Overview, Part 2

(Intermec Fingerprint 7.31) Continued from previous page!

SETUP:

MEDIA MEDIA:

MEDIA SIZE MEDIA:

MEDIA TYPE MEDIA:

PAPER TYPE MEDIA:

CONTRAST MEDIA:

TESTFEED PRINT DEFS:

HEAD RESIST PRINT DEFS:

TESTPRINT PRINT DEFS:

PRINT SPEED PRINT DEFS:

LTS SETUP:

PRINT DEFS SETUP:

NETWORK The LTS setup menus are only displayed if an optional LTS (Label-Taken Sensor) is installed in the printer. See Overview Part 5 Press Setup key to exit the Setup Mode. MEDIA SIZE:

XSTART MEDIA SIZE:

WIDTH MEDIA SIZE:

LENGTH MEDIA TYPE:

LABEL (w GAPS) TICKET (w MARK) TICKET (w GAPS) FIX LENGTH STRIP VAR LENGTH STRIP PAPER TYPE:

DIRECT THERMAL CONTRAST:

+0%

+2%

+4%

+6%

+8%

MEDIA TYPE:

+10%

-10%

-8%

-6%

-4%

-2%

TESTFEED:

[14 1]

HEAD RESIST:

[nnn]:

<ENTER> = PRINT:

<F5> = NEXT #1 PRINT SPEED:

[100]:

LTS:

LTS ADJUST LTS:

LTS TEST LTS:

LTS VALUE XSTART:

[24]:

WIDTH:

[832]:

LENGTH:

[1200]:

DIRECT THERMAL:

LABEL CONSTANT DIRECT THERMAL:

LABEL FACTOR LABEL CONSTANT:

[85]:

LABEL FACTOR:

[40]:

Press Enter key to perform a Testfeed. Comparator and amplifier values are read-only. Read-only value. Printhead resistance is automatically set at startup. Use <F5> to select type of test label. Press <Enter> to print it. If no label is printed, press <F3> for error message. SENSITIVITY 10 OUT OF 910 REMOVE LABEL AND PRESS ENTER REMOVE LABEL ENTER TO STOP LTS VALUE:

[10]:

56 Intermec EasyCoder F4 Installation & Operation Ed. 2 Setup Mode Overview, Part 3

(Intermec Fingerprint 7.31) If an optional Double Serial or Industrial Interface Board is fitted, additional menus will be displayed

(in case of Double Serial Interface Board, also see Overview Part 4):

Chapter 7 Setup Mode SETUP:

SER-COM,UART2 SETUP:

SER-COM,UART3 SER-COM,UART2:

BAUDRATE SER-COM,UART2:

PROT ADDR SER-COM,UART2:

CHAR LENGTH SER-COM,UART2:

PARITY SER-COM,UART2:

STOP BITS SER-COM,UART2:

FLOWCONTROL SER-COM,UART2:

NEW LINE SER-COM,UART2:

REC BUF SER-COM,UART2:

TRANS BUF SER-COM,UART2:

CONNECTED HW SER-COM,UART2:

PROTOCOL ADDR. BAUDRATE:

9600 19200 38400 57600 300 600 1200 2400 4800 PROT ADDR:

DISABLE ENABLE CHAR LENGTH:

8 7 PARITY:

NONE EVEN ODD MARK SPACE STOPBITS:

1 2 FLOWCONTROL:

RTS/CTS FLOWCONTROL:

ENQ/ACK FLOWCONTROL:

XON/XOFF NEW LINE:

CR/LF LF CR REC BUF:

[300]:

TRANS BUF:

[300]:

CONECTED HW:

RS232 INTELLITAGR PROTOCOL ADDR.

[1]:

These menus are only displayed if RS 485 is selected on "uart2:"

These menus are not displayed if RS 485 is selected on "uart2:"

RTS/CTS:

DISABLE ENABLE ENQ/ACK:

DISABLE ENABLE XON/XOFF:

DATA TO HOST XON/XOFF:

DATA FROM HOST RTS/CTS flowcontrol cannot be selected for the following types of hardware connection on "uart2:":

422 NON ISOLATED 422 ISOLATED DATA TO HOST:

DISABLE ENABLE DATA FROM HOST:

DISABLE ENABLE The selected type of hardware connection on "uart2:"

is displayed as one of the following alternatives (read-only):

RS232 422 NON ISOLATED 422 ISOLATED RS485 These menus are only displayed if RS 485 is selected on "uart2:"

Enter printer's protocol address (031). Intermec EasyCoder F4 Installation & Operation Ed. 2 57 Chapter 7 Setup Mode Setup Mode Overview, Part 4

(Intermec Fingerprint 7.31) If an optional Double Serial Interface Board is fitted, additional menus will be displayed:

SETUP:

SER-COM,UART3 SER-COM,UART3:

BAUDRATE SER-COM,UART3:

CHAR LENGTH SER-COM,UART3:

PARITY SER-COM,UART3:

STOP BITS BAUDRATE:

9600 19200 38400 57600 300 600 1200 2400 4800 CHAR LENGTH:

8 7 PARITY:

NONE EVEN ODD MARK SPACE STOPBITS:

1 2 SER-COM,UART3:

FLOWCONTROL FLOWCONTROL:

RTS/CTS FLOWCONTROL:

ENQ/ACK FLOWCONTROL:

XON/XOFF NEW LINE:

CR/LF LF CR REC BUF:

[300]:

TRANS BUF:

[300]:

CONNECTED HW:

RS232 SER-COM,UART3:

NEW LINE SER-COM,UART3:

REC BUF SER-COM,UART3:

TRANS BUF SER-COM,UART3:

CONNECTED HW RTS/CTS:

DISABLE ENABLE ENQ/ACK:

DISABLE ENABLE XON/XOFF:

DATA TO HOST XON/XOFF:

DATA FROM HOST RTS/CTS flowcontrol cannot be selected for the following types of hardware connection on "uart3:":

422 NON ISOLATED 20 mA CURRENT LOOP DATA TO HOST:

DISABLE ENABLE DATA FROM HOST:

DISABLE ENABLE The selected type of hardware connection on "uart3:"

is displayed as one of the following alternatives (read-only):

RS232 422 NON ISOLATED CURRENT LOOP 58 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 7 Setup Mode Setup Mode Overview, Part 5

(Intermec Fingerprint 7.31) If an optional an EasyLAN 100i interface board is fitted, additional menus will be displayed. SETUP:

SER-COM, UART1 Standard Setup Mode See Overview Part 1 SETUP:

NET-COM, NET1 NET-COM,NET1:

NEW LINE NEW LINE:

CR/LF LF CR SETUP:

FEEDADJ SETUP:

MEDIA Standard Setup Mode See Overview Part 1 Standard Setup Mode See Overview Part 2 SETUP:

PRINT DEFS Standard Setup Mode See Overview Part 2 SETUP:

NETWORK NETWORK:

IP SELECTION NETWORK:

IP ADDRESS NETWORK:

NETMASK IP SELECTION:

MANUAL DHCP BOOTP RARP IP ADDRESS:

10.1.12.79 NETMASK:

255.255.0.0 Use keys . and 09 to enter netmask. Use C-key to erase. Use keys . and 09 to enter netmask. Use C-key to erase. NETWORK:

DEFAULT ROUTER DEFAULT ROUTER:

10.1.12.1 Use keys . and 09 to enter router. Use C-key to erase. Press Setup key to exit the Setup Mode. Intermec EasyCoder F4 Installation & Operation Ed. 2 59 Chapter 8 Intermec Shell Startup Program Introduction Intermec Shell is a so called startup program (also called autoexec-

le), i.e. a program that automatically starts running when the printer is turned on. Intermec Shell helps the operator to choose between a number of standard or custom-made application programs and to start certain useful facilities, as listed below. Application Programs Intermec LabelShop (WYSIWYG label design program) Intermec Windows Driver (for printing Windows programs) Intermec Fingerprint (for creating your own programs) Intermec Direct Protocol (easy-to-use slave protocol) LINE_AXP.PRG (line analyzer program) Other application programs in the printer's memory1 Other Facilities Setup Mode Print Setup Testfeed Test Label Default setup Update PC-card Reboot

(manual setup from printer's keyboard)

(printing setup on label)

(formfeeds + auto-adjust of the LSS)

(printing of test labels)

(resetting all setup parameters to default)

(downloading data from a computer to a PC-card inserted in the printer, or upgrading the printer's rmware from a PC-card)

(restarting the printer) Intermec Shell is factory-installed in the printer's permanent memory (device "rom:"). This implies that if you insert a memory card with another startup le before you turn on the printer, or if there is a startup le stored in the printer's permanent memory

(device "c:"), this startup le will be used instead of Intermec Shell (see chapter 4;Startup Files). 1/. A prerequisite is that the program is provided with the extension .PRG. However, some original Intermec utility programs are excluded:

ERRHAND.PRG FILELIST.PRG LBLSHTXT.PRG MKAUTO.PRG LSS-SENSOR.PRG SHELLXP.PRG WINXP.PRG 60 Intermec EasyCoder F4 Installation & Operation Ed. 2 Starting Up with Intermec Shell Chapter 8 Intermec Shell Startup Program A few seconds after you have turned on the power to the printer and the initialization is completed, the countdown menu of the Intermec Shell program will be displayed:

ENTER=SHELL 5 sec. v.4.4 Now you have 5 seconds to enter Intermec Shell by pressing the

<Enter> key. Provided you have a working two-way communication with a terminal program in a host computer, you may as an alternative enter the Terminal Setup by transmitting TTT or ttt to the printer. The Terminal Setup is described later in this chapter. The lower line keeps you informed on how much time you have left. Should the time run out before you have taken any action to enter Intermec Shell, the last selected application in Intermec Shell will be opened. This implies that if you use the same application all the time, you will only need to turn on the power, once the application has been selected. If no other application has been selected yet, the default choice will be displayed when the countdown is completed, e.g.:

FINGERPRINT 7.31 This message means that you have entered the immediate mode of Intermec Fingerprint with "uart1:" (the standard RS 232C port) selected as std I/O channel (see Intermec Fingerprint manuals). If you want to enter another application, just restart the printer and enter Intermec Shell before the countdown is completed. If you enter the Intermec Shell from the countdown menus, the Select Application menu will be displayed:

SHELL SEL. APPLICATION In this menu, you can choose between three options:

Go to a stack of menus, where you can select an application program, by pressing <Enter>. Go to the Facilities part of Intermec Shell by pressing <F5>. Start the Terminal Setup program by transmitting TTT or ttt from the host. Intermec EasyCoder F4 Installation & Operation Ed. 2 61 Chapter 8 Intermec Shell Startup Program Starting Up with Intermec Shell, cont'd. 1/. When the Intermec Labelshop application is started, the printer's communication setup is changed to the following values:

Baudrate: 57600 Char. Length: 8 Parity: None Stopbits: 1 RTS/CTS: Enable ENQ/ACK: Disable XON/XOFF to host: Disable XON/XOFF from host: Disable New Line: CR/LF Receive buffer: 600 Transmit buffer: 600 If another application is selected later, these setup parameters will still be valid, unless the new application includes instructions to automatically change the setup. The setup could also be changed manually in the Setup Mode. In Intermec Shell, the options are presented in stacks of menus, organized as in nite loops, where you can select the desired option, as illustrated by the diagram below. Select Application The Select application option allows you to enter a stack of menus showing the various application programs in the printer's memory. Current appl. starts the last selected application (by default Intermec Fingerprint with "uart1:" selected as std I/O channel). Intermec LabelShop sets up the printer1 for the various Intermec LabelShop label design programs for Microsoft Windows. This option requires that you also select a std IN/OUT channel, i.e. the channel you want to use for communication between the printer and the computer. Refer to the Intermec LabelShop manuals. Intermec Windows Driver selects the "centronics:" parallel interface as standard IN channel and sets up the printer for the various Intermec Windows Drivers, which you can use on a personal computer to produce printouts from almost any program run under Microsoft Windows. The Windows Driver requires an optional Centronics interface board to be tted in the printer. Intermec Fingerprint is used to create, modify or run programs written in the Intermec Fingerprint programming language. This option requires that you also select a standard IN/OUT channel, i.e. the channel you want to use for communication between the printer and the computer (normally "uart1:"). Refer to the Intermec Fingerprint manuals. Intermec Direct Protocol is an easy-to-use printer protocol for down-loading label layouts and variable input data to a printer from a host computer. This option requires that you also select a standard IN/OUT channel, i.e. the serial channel you want to use for communication between the printer and the host. Normally, select "uart1:". Refer to the Intermec Direct Protocol Programmer's Guide. LINE-ALY.PRG (Line Analyzer) is a Fingerprint program that captures characters received by the printer on a communication channel and prints them on labels as described later in this chapter. Other Application Programs If the printer contains any other application programs standard or custom-made these will presented as additional options. 62 Intermec EasyCoder F4 Installation & Operation Ed. 2 Starting Up with Intermec Shell, cont'd. Chapter 8 Intermec Shell Startup Program Select Other Facilities As an alternative to selecting an application, you can step through a number of other useful facilities:

Setup allows you to enter the Setup Mode to set up the printer by means of its built-in keyboard, see chapter 7 Setup Mode. Print Setup allows you to produce a printout of the printer's current setup values (test label #5). Testfeed allows you to feed out a number of label, ticket, tag or pieces of strip while the printer auto-adjusts its paper feed and label stop sensor or black mark sensor. It is recommended to perform a Testfeed operation each time you load a new roll of labels (or similar). Test Label allows you to print a series of four test labels

(test labels #1 #4) in order to test the printout quality and printhead alignment. The labels are presented in an in nite loop, so you can print the series over and over again. Press

<Enter> for each new label. Default Setup allows you to reset all setup parameters to their respective default values, as listed in chapter 6. Software Update is used for two purposes:

- Update PC-card allows the printer to be used as a Flash PC-card programming device. By means of the Zmodem commun-ication tool, les can be downloaded from a PC to a Flash PC-card1 inserted in the memory card slot in the printer's rear plate. Warning! If the Flash PC-card contains an earlier rmware version than the one in the printer, the printer's rmware will be downgraded without warning.

- Update rmware is used to upgrade the printer's rmware from a new rmware version stored as a le in a PC. Reboot has the same effect as turning off and on the power to the printer. To exit Intermec Shell without having selected any application program, use Reboot or restart the printer. Then wait for the 5 seconds countdown without taking any action, and the last selected application will be opened. 1/. Only Flash PC-cards approved by Intermec can be used. Intermec EasyCoder F4 Installation & Operation Ed. 2 63 Chapter 8 Intermec Shell Startup Program Intermec Shell 4.4 Diagram POWER ON ENTER=SHELL 5 sec. v.4.4 SHELL SEL. APPLICATION SEL. APPLICATION CURRENT APPL. Last selected application is started ENTER=SHELL 4 sec. v.4.4 ENTER=SHELL 3 sec. v.4.4 ENTER=SHELL 2 sec. v.4.4 ENTER=SHELL 1 sec. v.4.4 Last selected application is started Default:

Fingerprint 7.31 w. std I/O = "uart1:"

Legend:

Return to previous menu. Proceed to next menu. Accept displayed option and proceed, or execute displayed option. Perform a Testfeed anywhere in Intermec Shell. Enter the Setup Mode from anywhere in Intermec Shell. Enter Terminal Setup by transmitting T T T or t t t to printer, when menus marked with a shade of grey are displayed!

d e t r a t s s i n o i t a c i l p p a d e t c e e s e h T l SEL. APPLICATION LABELSHOP SEL. APPLICATION WINDOWS DRIVER The Windows driver option requires an optional Centronics interface pcb. SEL. APPLICATION Fingerprint 7.31 STD I/O CHANNEL UART1 SEL. APPLICATION Direct Protocol STD I/O CHANNEL UART2 STD I/O CHANNEL UART3 STD I/O CHANNEL CENTRONICS STD I/O CHANNEL net1:

See note 1 See note 1 See note 1 See note 1 SHELL SETUP SHELL PRINT SETUP SHELL TESTFEED SHELL TEST LABEL SEL.APPL rom:

LINE_AXP.PRG SETUP:

SER-COM,UART1 Note 1: Dotted options are only shown if an appropriate optional interface pcb is fitted. See Setup Mode Prints a list of current setup values (test label #5). Performs a Testfeed, i.e. feeds out a number of blank copies while autoadjusting the label stop sensor. Prints test labels #1 #4 in a loop. Press Enter for each new label. SHELL DEFAULT SETUP ARE YOU SURE ?

Y=ENTER/ N=F5 DEFAULT SETUP PERFORMED SHELL SOFTWARE UPDATE UPDATE:

PC-CARD?

PC-CARD ERASE TRANSFER FILE USING ZMODEM PROGRAMMING PC-CARD PROGRAMMING COMPLETED SHELL REBOOT UPDATE:

FIRMWARE TRANSFER FILE USING ZMODEM Restarts the printer (same as power off/on) Printer rebooted automatically 64 Intermec EasyCoder F4 Installation & Operation Ed. 2 Terminal Setup Starting Terminal Setup Solving Communication Problems 1/. By default, "uart1:" is standard IN/OUT channel and should be used for communi-

cation between printer and host, e.g. for running Terminal Setup or for program-

ming. However, other ports could be appointed standard IN and/or OUT chan-

nel by means of the Intermec Fingerprint statement SETSTDIO. Refer to the Inter-

mec Fingerprint manuals for further information. Chapter 8 Intermec Shell Startup Program The Terminal Setup program in Intermec Shell allows the operator to control the whole Intermec Shell program remotely from a host computer or terminal and also to read or change the printer's setup. Obvious prerequisites are that there must be a working two-way

(serial) communication between printer and host, and that the host runs a suitable communication program (e.g. MS Windows Terminal) that can transmit and receive data in ASCII format, i.e. as printable characters. Set up the terminal as VT100. Enter Terminal Setup by transmitting three upper- or lowercase T characters (TTT or ttt) while the printer either shows the Intermec Shell countdown menus or the Select Application menu. If this does not work, the communication protocols of the printer and the host probably do not match, or there is some other communication error, e.g. a defect communication cable, wrong port selected on the host, or cable connected to some other port than "uart1:"

on the printer1. You can check and change the printer's setup in the Setup Mode, which you can enter by pressing the < Setup> key on the printer's built-in keyboard. Proceed as described in chapter 8 Setup Mode. Among the facilities in Intermec Shell, you will also nd a number of options that allow you to read or change the communication setup of the printer:

Setup This is another way of entering the Setup Mode, where you can browse through the setup parameters and make changes by means of the printer's keyboard. Print Setup Here you can print the current setup on one or more labels. Default Setup This option allows you to reset the communication parameters for all serial communication channels on the printer to default values. Change the communication setup of the printer according to the host or vice versa. Once printer and host has been set up with the same communication parameters, go to the Select Application menu and use the triple T (TTT or ttt) to start Terminal Setup. Intermec EasyCoder F4 Installation & Operation Ed. 2 65 Chapter 8 Intermec Shell Startup Program Terminal Setup, cont'd. Using Terminal Setup The Terminal Setup program is self-instructing by means of prompts. You can move around in Intermec Shell in the same manner as when you control Intermec Shell manually by means of the printer's display and keyboard. The Setup part of Terminal Setup follows the same structure as setup les, see later in this chapter. Comprehensive explanations of the various setup parameters can be found in Chapter 7 Setting Up the Printer. When you transmit the triple T (TTT or ttt) to the printer, the following message will appear on printer's display:

SETUP FROM TERMINAL On the screen of the host, another message will appear:

Welcome to SHELL v.4.4 in terminal mode

Answer Y <CR> for Yes, <CR> for No.

SHELL SEL. APPLICATION

(Y / N / B):

From here on, you can move around in Intermec Shell according to the diagram in the chapter Using Intermec Shell by answering Y (=Yes), N (=No), or B (=Back) to the prompts that successively appear on the screen. Note that the program also accepts the corresponding lowercase characters, i.e. y, n, and b. 66 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 8 Intermec Shell Startup Program Terminal Setup, cont'd. Selecting an Application This example shows how you for example can select the Intermec Fingerprint application:

SHELL SEL. APPLICATION

(Y / N / B):Y

SEL. APPLICATION CURRENT APPL.

(Y / N / B):N

SEL. APPLICATION LABELSHOP

(Y / N / B):N

SEL. APPLICATION WINDOWS DRIVER

(Y / N / B):N

SEL. APPLICATION Fingerprint 7.31

(Y / N / B):Y

STD I/O CHANNEL UART1

(Y / N / B):Y When you have answered the nal prompt, the printer will start the selected application. Intermec EasyCoder F4 Installation & Operation Ed. 2 67 Chapter 8 Intermec Shell Startup Program Terminal Setup, cont'd. Changing the Setup To set up the printer or use any other of the facilities, answer N

(=No) to the Select Application prompt. The following example illustrates how to enter the Setup Mode:

SHELL SEL. APPLICATION

(Y / N / B):N

SHELL SETUP

(Y / N / B):Y

SETUP:

SER-COM,UART1 From here you can navigate through the Setup Mode by means of keys on a VT100 terminal according to the same principles as when using the printer's own keyboard (see overviews in chapter 7):

Key Action u Move one menu to the left on the same level (same as <F1>). d Move one menu to the right on the same level (same as <F2>). e Display error message at test label printing failure

(same as <F3>). b Move up one level or scroll back in a stack of menus

(same as <F4>). f Move down one level or scroll forward in a stack of options (same as <F5>). x Exit the setup (same as <Setup>). 0 9 Enter numeric values. Specify negative values (same as < . >). Enter Acknowledge and move to next menu, perform testfeeds, or print test labels (same as <Enter>). Backspace Delete one character to the left of the cursor (same as <C>). 68 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 8 Intermec Shell Startup Program Terminal Setup, cont'd. Exiting Terminal Setup To exit the Terminal Setup program, e.g. after having changed the setup, you must select the Reboot option after having stepped through all the facility options, as illustrated below:

SHELL PRINT SETUP

(Y / N / B):N

SHELL TESTFEED

(Y / N / B):N

SHELL TEST LABEL

(Y / N / B):N

SHELL DEFAULT SETUP

(Y / N / B):N

SHELL SOFTWARE UPDATE

(Y / N / B):N

SHELL REBOOT

(Y / N / B):Y Intermec EasyCoder F4 Installation & Operation Ed. 2 69 Chapter 8 Intermec Shell Startup Program Line Analyzer The Line Analyzer (LINE_AXP.PRG) is a program written in the Intermec Fingerprint programming language and intended to help solving possible communication problems. As the name implies, the Line Analyzer captures all incoming characters on a specified communication channel and prints them on one or several labels. Printable characters are printed in black-on-white, whereas control characters and space characters (ASCII 0032 dec) are printed in white on a black background. While the printer is receiving data, the Ready control lamp blinks. There is a 0.5 sec timeout. If no more character has been received after 0.5 seconds, the program considers the transmission terminated and prints out a label. As long as a continuous string of characters is being received, the program wraps the lines until the label is full and then starts to print another label. At the bottom of each label, the following information is printed:

Page number Number of characters printed on the label Total of characters received so far The Line Analyzer is displayed as the option LINE_ALY.PRG"

under the SEL. APPLICATION menu. After the Line Analyzer has been selected and the printer has started up again, the printer feeds out two labels and the following menu is displayed:

Line Analyzer Sel.port(1-4) 1 Enter the desired communication port by means of the numeric keys on the printer's keyboard:

1 = "uart1:"

2 = "uart2:"

3 = "uart3:"

4 = "centronics:"

5 = "net1:"

If the printer is not tted with the speci ed port, an error message appears in the display and you can select another port:

Line Analyzer Error:56 70 Intermec EasyCoder F4 Installation & Operation Ed. 2 Options Introduction Chapter 9 The EasyCoder F4 is designed to provide a high degree of exibility by means of a modular design. By adding a collection of optional devices to the basic concept, the printer can be adapted for a variety of applications. Most options can easily be installed by the operator whereas some options should be installed by an authorized service technician, or are only available as factory-installed options. Below is a description of some of the many options available for EasyCoder F4. 1.5" Paper Spool 3" Adapter Rewinder &

Guide Shaft Label-Taken Sensor Short Side Door Long Side Door Quick-Load Guides Intermec EasyCoder F4 Installation & Operation Ed. 2 71 Chapter 9 Options Side Doors Rewind Unit Paper Supply Spool 3" Adapter The EasyCoder F4 comes with either a short side door, that only covers the print unit, or with a long side door, that encloses the entire paper compartment. The long side door has a slot for external paper supply. The long side door is generally illustrated throughout this manual, but pictures of the short side door can be found at the start of this chapter and in chapter 5 Paper Load/Quick-Load. The rewind unit is an optional device for peel-off operation, i.e. the labels are separated from a backing paper (liner) after printing and the backing paper is wound up on an internal spool. The rewind kit also includes a guide shaft. Peel-off cannot be combined with quick-load guides, see below. The rotating paper supply spool is designed to t paper roll cores with an internal diameter of 38 40 mm (1.5"). The spool can be tted in the same positions as the paper hanger (see chapter 3 Installation). Being factory installed, the position of the paper supply spool is not intended to be changed by the operator. the combination of high print speed and the momentum of large and heavy paper roll (may cause slacks and jerks in the paper web that may impair the printout quality, especially when printing ladder style bar codes (i.e. with bars running across the web). Thus, in case of print speed exceeding 150 mm/sec. (6"/sec,) in combination with a full width paper roll and a paper roll diameter of 200 mm (8") or more, we do not recommend the use of a rotating paper supply spool. The 3 inch/76 mm adapter is used in connection with a rotating paper supply spool and makes it possible to use paper rolls with 3 inch/76 mm inner diameter paper cores. The 3" adapter cannot be used in connection with a paper hanger. The adapter is pressed onto the paper supply spool and held in place by a screw 72 Intermec EasyCoder F4 Installation & Operation Ed. 2 Quick-Load Guides Label-Taken Sensor EasySet Bar Code Wand Real-Time Clock Chapter 9 Options For Quick-Load operation (see chapter 5 Paper Load), a set of paper guides is tted at the rear of the print unit instead of the standard guide ring. The outer guide is adjustable for different paper widths. The quick-load guides are included as standard in the delivery (either factory- tted or loose). They can easily be tted by the operator:

1. Open the upper paper guide (see illustration in chapter 11 Maintenance/Cleaning the Paper Guides). 2. Pull out the standard guide ring from the shaft. 3. Fit the quick-load guides onto the shaft as illustrated on the rst page of this chapter. The Label-Taken Sensor (LTS) is a photoelectric sensor, which enables the printer's rmware to detect if the latest printed label, ticket, tag etc. has been removed before printing another copy. The LTS can be enabled or disabled by means of the instructions LTS& ON and LTS& OFF respectively in Intermec Fingerprint and the Intermec Direct Protocol. The EasySet bar code wand is primarily intended to facilitate setup in regard of paper type, but can also be used to change all other setup parameters. This is done by scanning a pre-printed CODE 128 bar code composed according to a special standard (FNC3 in the bar code input data speci es a setup parameter). The bar code wand can also be used to read other CODE 128 bar codes as input data to a Intermec Fingerprint program. A selection of setup bar codes is provided in Appendix 4. For further information on how to compose setup bar codes, see the Intermec Fingerprint 7.xx Reference Manual. The bar code wand is connected to the topmost connector on the printer's rear plate, immediately to the right of the main switch. The Real-Time Clock circuit (RTC) relieves the operator or the overhead computer system from having to set the clock/calendar by means of the Intermec Fingerprint instructions DATE$ and TIME$

after each power up. The RTC has its own battery backup with a life of 10 years or more. Intermec EasyCoder F4 Installation & Operation Ed. 2 73 Chapter 9 Options Interface Boards RFID Option A number of different interface boards are available for use with the EasyCoder F4. The interface boards are either factory tted or can easily be tted by an authorized service technician. The EasyCoder F4 can accommodate one such interface board. The interface boards for the EasyCoder F4 are presently:

Parallel Interface Board (IEEE 1284) Double Serial Interface Board Industrial Interface Board EasyLAN 100i Interface Board (Ethernet) Refer to Appendix 3 Interfaces for more information on interface boards. RFID (radio frequency identification) option modules are available for use with the EasyCoder F4. The RFID option modules are either factory fitted or fitted by an authorized service technician. The EasyCoder F4 can accommodate only one option module. The RFID option module occupies the same chassis slot as other inter-

face boards listed in Chapter 9, and cannot be used in conjunction with, or in addition to, any of the optional interface boards listed. 74 Intermec EasyCoder F4 Installation & Operation Ed. 2 Troubleshooting Chapter 10 Use this list to correct possible printout troubles or aws in printout quality, and to decide when assistance from the Service dept. of the nearest Intermec distributor is required. Note that most problems are due to operating errors or normal wear of the printhead. Symptom Possible Cause Remedy Refer to Overall weak printout Wrong Paper Type setup Change setup Chapter 6 Low Contrast setup Change setup Chapter 6 Printhead pressure too low Adjust Chapter 12 Worn printhead Replace printhead Chapter 11 Wrong printhead voltage Replace CPU board  Call Service Printout weaker on one side Uneven printhead pressure Adjust arm alignment Chapter 13 Weak spots Foreign particles on paper Clean or replace Chapters 5 Poor paper quality Use Intermec paper Appendix 2 Worn printhead Replace printhead Chapter 11 Worn platen roller Check/replace  Call Service Overall dark printout Wrong Paper Type setup Change setup Chapter 6 Too high Contrast setup value Change setup Chapter 6 Printhead pressure too high Adjust Chapter 12 Wrong printhead voltage Replace CPU board  Call Service Excessive bleeding Wrong Paper Type setup Change setup Chapter 6 Contrast setup value too high Change setup Chapter 6 Printhead pressure too high Adjust Chapter 12 Faulty energy control Replace CPU board  Call Service Dark lines along paper web Foreign objects on printhead Clean printhead Chapter 11 White lines along paper web Printhead dirty Clean printhead Chapter 11 Missing dots on printhead Replace printhead Chapter 11 Large part of dot line missing Wrong X-start or Width setup Change setup Chapter 6 Failing printhead Replace printhead Chapter 11 Failing strobe signal Check CPU-board  Call Service Printout missing along inner edge Bad paper alignment Adjust Chapter 5 Small core and hanger in upper position Move hanger to lower pos. Chapter 3 X-start setup value too low Increase Chapter 6 Paper feed not working properly Changed media characteristics Perform a TESTFEED Chapter 5 Wrong start- and stop adjust values Check/change Chapter 6 Wrong Media Type setup Check/change Chapter 6 Wrong sensor position Check/change Chapter 12 Dirty or blocked sensors Clean paper guides Chapter 11 Faulty sensors Replace  Call Service Intermec EasyCoder F4 Installation & Operation Ed. 2 75 Chapter 11 Maintenance Printhead Cleaning Cleaning of the printhead on a regular basis, preferably in connection with each ribbon or paper load, is important for the life of the printhead and for the printout quality. Below is a description of how to clean the printhead by means of Cleaning Cards. If additional cleaning is required, e.g. for removing adhesive residue from the platen roller or tear-off edge, use a cotton swab moistened with isopropyl alcohol. Caution!

Isopropyl alcohol [(CH 3)2CHOH; CAS 67-63-0] is a highly ammable, moderately toxic and mildly irritating substance. 1 2 Open the side door. Turn the printhead lift knob clockwise to lift the printhead. 76 Intermec EasyCoder F4 Installation & Operation Ed. 2 Printhead Cleaning, cont'd. Chapter 11 Maintenance 3 5 4 Remove the paper, if any. Open the cleaning card envelope and pull out the cleaning card. Read the warning text. 6 Insert most of the cleaning card under the printhead (1). Close the printhead (2). Pull out the cleaning card (1) and open the printhead (2). Intermec EasyCoder F4 Installation & Operation Ed. 2 77

 

 

Chapter 11 Maintenance Printhead Cleaning, cont'd. 7 9 8 Wait for approx. 30 seconds to allow the cleaning uid to dissolve the residue. Insert most of the cleaning card under the printhead (1). Close the printhead (2). 10 Pull out the cleaning card. If necessary, repeat the process with a new cleaning card. Allow the cleaned parts to dry before loading any paper. 78 Intermec EasyCoder F4 Installation & Operation Ed. 2 External Cleaning Chapter 11 Maintenance 1 3 2 Always remove the power cord before cleaning!

Wipe external surfaces with a soft cloth slightly moistened with water or a mild detergent. 4 Never spray the printer. Protect it from water when cleaning the premises. Never use any sharp tools for removing stuck labels. The printhead and rollers are delicate. Intermec EasyCoder F4 Installation & Operation Ed. 2 79 Chapter 11 Maintenance Cleaning the Paper Guides Both parts of the label stop sensor, which controls the paper feed, are covered by plastic guides. The guides are provided with seemingly non-transparent areas, through which the light between the two parts of the label stop sensor is transmitted. These areas (indicated by a shade of grey in illustration #2 below) must be kept clean from dust, stuck labels, and adhesive residue. If the printer starts to feeed our labels in an unexpected way. lift the upper guide as described below and check for anything that may block the beam of light (dust, stuck labels, adhesive residue etc.). If necessary, clean the guides using a cleaning card or a soft cloth soaked with isopropyl alcohol. Do not use any other the of chemical. Be careful not to scratch the guides. Caution!

Isopropyl alcohol [(CH 3)2CHOH; CAS 67-63-0] is a highly ammable, moderately toxic and mildly irritating substance. 1 2 Lift the inner part of the upper guide and pull it outwards,disengaging it from the lower guide. Take care not to damage the cable. Tilt the upper guide upwards and clean the areas marked with grey. After cleaning, reas-

semble in reverse order. 80 Intermec EasyCoder F4 Installation & Operation Ed. 2 Printhead Replacement Chapter 11 Maintenance The printhead is subject to wear both from the direct thermal paper and from the rapid heating and cooling process during printing. Thus, the printhead will require periodical replacement. Time between printhead replacements depends on the print images, the type of paper in use, the amount of energy to the printhead, and several other factors. Note!

While replacing the printhead, the power should be switched off. 1 2 Open the side door. Turn the printhead lift knob clockwise to lift the printhead. Intermec EasyCoder F4 Installation & Operation Ed. 2 81 Chapter 11 Maintenance Printhead Replacement, cont'd. 3 5 4 Remove the paper, if any. Pull the printhead bracket away from the magnet in the pressure arm. 6 Snap-lock Disconnect the printhead bracket from the print mechanism as indicated by the arrows and pull out the printhead as far as the cables allow. Disconnect the cables from the printhead. Note the snap-lock on the inner connector. Pull at the connectors not the cables!

82 Intermec EasyCoder F4 Installation & Operation Ed. 2 Printhead Replacement, cont'd. 7 8 Chapter 11 Maintenance Connect the two cables to the replacement printhead. Put back the printhead in reserse order and check that the printhead cables run freely. 9 10 Close the printhead so the magnet engages the printhead bracket. Load a new supply of paper as described ear-

lier in this manual. Intermec EasyCoder F4 Installation & Operation Ed. 2 83 Chapter 12 Adjustments Narrow Labels Adjustment Nut Pressure Arm Centre of Paper The printer is factory-adjusted for full size paper width. When using paper less than full width, it is recommended to adjust the pressure arm so it becomes centred on the paper. Thereby, an even pressure across the paper is obtained. A poorly adjusted pressure arm may be detected by a weaker printout on the inner part of a less than full width paper. Similarly, when reverting to a wider paper, the arm should be adjusted, or the printout on the outer part of the paper could be weak. To adjust the pressure arm, proceed as follows:

Loosen the nut that holds the pressure arm. Move the arm inwards or outwards until the arrow on the tip of the arm becomes centre-aligned with the paper web. While moving the arm, push at the part where the nut is situated, not at the tip. If the arm is hard to move, lift the printhead and pull the printhead bracket free from the magnet in the arm. After having centred the arm, lock it by tightening the nut. 84 Intermec EasyCoder F4 Installation & Operation Ed. 2 Chapter 12 Adjustments The label stop/black mark sensor (LSS) is a photoelectric sensor that controls the printer's paper feed by detecting gaps between labels, slots in paper strip, or black marks, depending on the printer's setup in regard of media type (see chapter 6 Setting Up the Printer). A prerequisite is obviously that the LSS is aligned with the slots or black marks. Thus, the LSS can be moved laterally between 5 xed positions. There is one sensor on top of the upper paper guide and underneath the bottom of the print unit. These two guides must be set individually to the same position. Push them inwards as far as they go and then pull them out one at the time while counting the clicks from the snap-locks. The various detection points of the sensor in relation to the inner edge of the paper are as follows:

One click out 3 mm .118"

Two clicks out 8 mm .315"

Three clicks out 12 mm .472"

Four clicks out 16 mm .639"

Five clicks out 20 mm .787"

If using irregularly shaped labels, align the LSS with the front tips of the labels Upper part of LSS Label Stop Sensor Position One Sensor One Diode + One Sensor Lower part of LSS Print Unit

(printhead and headlift shaft omitted for improved visibility) Intermec EasyCoder F4 Installation & Operation Ed. 2 85 Chapter 12 Adjustments Printhead Pressure The pressure of the thermal printhead against the paper is factory adjusted. However, the use of thicker or thinner paper than normal could require the printhead pressure to be readjusted. Using a at-tipped screwdriver, turn the adjustment screw clockwise for increased pressure (+), or counter-clockwise for less pressure (-). Print a few labels, preferably test labels (see chapter 6 Setting Up the Printer), and check the printout. Increased pressure generally gives a darker printout and vice versa. Repeat until the desired result is obtained. To return to the factory setting, tighten the screw (+) as far as it goes and then loosen it (-) six (6) full turns. Note!

Do not use a higher printhead pressure than necessary, because it may increase the wear of the printhead and thus shorten its life. Adjustment Screw 86 Intermec EasyCoder F4 Installation & Operation Ed. 2 Appendix 1 Technical Data Printing Print Technique Direct Thermal Printhead Resolution 8 dots/mm (203.2 dpi) Print Speed (variable) 100 200 mm/sec. ( 4 8"/sec.) Print Width (max) 104 mm (4.095") = 832 dots Print Length (max) 32767 dots = 409.5 cm1 Media Width (min/max) 25 114.3 mm (1 4.5") Standard paper guide Media Width (min/max) 40 114.3 mm (1.57 4.5") Quick-Load guides Paper Roll Diameter (max) 213 mm (8.38") Short door/no rewind Paper Roll Core Diameter 38 40 mm (1.5") or 76 mm (3") Print Directions 4 Modes of Operation Tear Off Yes Peel Off Optional Requires Rewind Unit Firmware Operating System Intermec Fingerprint 7.31 Incl. Direct Protocol Smooth Fonts TrueDoc and TrueType fonts Built-in scalable fonts (std) 15 Unicode fonts2 Built-in bar code symbologies (std) 36 Startup Program (std) Intermec Shell 4.4 Physical Measures Dimensions (W x L x H) 244 x 397 x 178 mm (9.61 x 15.63 x 7.00") w. Long side door Weight (excluding media) 7 kgs (15.5 lbs) Depending on model Ambient Operating Temperature +5C +40 C (+41F +104 F) Humidity 20 80% non-condensing Electronics Microprocessor 32 bit RISC On-board Flash SIMMs 1 2 Std. 1 x 2 Mbytes On-board DRAM SIMM 1 Std. 4 Mbytes Real-Time Clock Option 10+ years life Power Supply Mains Voltage >90 <264 V AC, 45 65 Hz PFC Regulation IEC 61000-3-2 Maximum Power Consumption Continuous 140 W; Peek 300W Intermec EasyCoder F4 Installation & Operation Ed. 2 87 Appendix 1 Technical Data 3 1 Yes Yes Yes Yes 2 1 1 1 x RS 232C + 1 x USB 22 keys membrane switch type 2 x 16 character LCD w. background light Technical Data, contd. Sensors Label Gap/Black Mark/Out of Paper Printhead Lifted Controls Control Lamps Display Keyboard Print Button Beeper Data Interfaces Serial Bar Code Wand Electronic Keys Connection for Optional Interface Boards Memory Card Adapter Accessories and Options RFID Module Rewind Unit Paper Supply Spool 3 Adapter for Paper Supply Spool Short Side Door Long Side Door Label Taken Sensor Real-Time Clock Quick-Load Guides RS 232C Cable EasySet Bar Code Wand Parallel Interface Board Double Serial Interface Board Industrial Interface Board EasyLAN 100I Interface Board External Alphanumeric Keyboard Flash Memory Cards Electronic Keys 1. The max. print length is also restricted by the amount of free DRAM memory. 2. Latin, Greek, and Cyrillic fonts according to Unicode standard are included. 3. Depending on model, the printer may be delivered with either a long or a short side door. Option Option Option Option Option3 Option3 Option Option Standard Option Option Option Option Option Option Option Option Option 5 fixed positions For setup Future option Flash or SRAM cards For peel-off operation Replaces hanger 10+ years life Fitted in some models For quick setup IEEE 1284 Ethernet

= 64 Mbit (8 MB) 88 Intermec EasyCoder F4 Installation & Operation Ed.2 Appendix 2 Media Speci cations Direct Thermal Labels Intermec offers two quality grades of direct thermal paper for the EasyCoder range of printers:

Premium Quality: Top-coated papers with high demands on printout quality and resistance against moisture, plasticisers and vegetable oils. Examples...

- Duratherm II,

- Duratherm II Tag

- Duratherm Ltg.

- Duratherm IR

- Top Board

- Premium Economy Quality: Non top-coated papers with less resistance to moisture, plasticisers and vegetable oils. In all other respects, it is equal to Premium Quality. Examples...

- Economy

- Eco Board Intermec EasyCoder F4 Installation & Operation Ed. 2 89 Appendix 2 Media Speci cations Paper Roll Size 38 40 mm (1.5") or 76.2 mm (3") Must not protrude outside the web. Core Diameters:

Width:

The web must be wound up on the core in such a way that the printer can pull the end of the web free. Roll Max. diameter (internal supply only):

- Position 1 152 mm (6.00")

- Position 2 213 mm (8.38")

- Position 3 203 mm (8.00") Max. width: 114.3 mm (4.50") Min. width (standard): 25 mm (1.00") Min. width (Quick-Load): 40 mm (1.57") Max. web thickness: 175 m (0.007") The maximum recommended web thickness is 175m. A thicker web may be used, but print quality will be reduced. Web stiffness is also important and must be balanced against web thickness to maintain print quality. Paper rolls fitted inside the printer should be wound with the printable side facing outwards. The paper supply must not be exposed to dust, sand, grit, etc. Any hard particles, however small, can damage the printhead. 90 Intermec EasyCoder F4 Installation & Operation Ed. 2 Paper Non-Adhesive Strip Appendix 2 Media Speci cations a Web Width:

Maximum:

Minimum (standard):

Minimum (Quick-Load):

Media Type Setup:

Fix length strip Var length strip 114.3 mm 25.0 mm 40.0 mm

(4.50")

(1.00")

(1.57") Intermec EasyCoder F4 Installation & Operation Ed. 2 91 Appendix 2 Media Speci cations Paper, cont'd. Self-Adhesive Strip

(4.50")

(1.00")

(1.57") 114.3 mm 25.0 mm 40.0 mm a Web Width (including backing paper):

Maximum:

Minimum (standard):

Minimum (Quick-Load):

b Backing Paper The backing paper must not extend more than a total of 1.6 mm

(0.06") outside the paper and should protrude equally on both sides. c Paper Width (excluding backing paper):

Maximum:

Minimum:

Media Type Setup:

Fix length strip Var length strip 112.74 mm 23.8 mm

(4.43")

(0.94") 92 Intermec EasyCoder F4 Installation & Operation Ed. 2 Paper, cont'd. Self-Adhesive Labels Appendix 2 Media Speci cations

(0.32")

(4.43")

(0.94")

(4.50")

(1.00")

(1.57") 112.7 mm 23.8 mm 114.3 mm 25.0 mm 40.0 mm 8.0 mm depends on DRAM size a Web Width (including backing paper):

Maximum:

Minimum (standard):

Minimum (Quick-Load):

b Backing Paper The backing paper must not extend more than a total of 1.6 mm

(0.06") outside the paper and should protrude equally on both side. Recommended min. transparency: 40% (DIN 53147). c Label Width (excluding backing paper):

Maximum:

Minimum:

d Label Length:

Minimum:

Max label length:

Under favourable circumstances, a minimum label length down to 4 mm (0.16") could be used. It requires the sum of the label length

(d) and the label gap (e) to be larger than 7 mm (0.28"), that batch printing is used, and that no pull back of the paper is performed. Intermec does not guarantee that such short labels will work, but it is up to the user to test this in his unique application. e Label Gap:

Maximum:

Recommended:

Minimum:

The Label Stop Sensor must be able to detect the extreme front edges of the labels. It can be moved between 5 xed positions at the following distances from the inner edge of the paper. 3 mm (.118") 8 mm (.315") 12 mm (.472") 16 mm (.639") 20 mm (.787") Media Type Setup:

Label (w gaps) 21.3 mm 3.0 mm 1.2 mm

(0.83")

(0.12")

(0.05") Intermec EasyCoder F4 Installation & Operation Ed. 2 93 Appendix 2 Media Speci cations Paper, cont'd. Tickets with Gap 8.0 mm

(4.50")

(1.00")

(1.57") 114.3 mm 25.0 mm 40.0 mm a Web Width:

Maximum:

Minimum (standard):

Minimum (Quick-Load):

b Copy Length:

Min. length between slots:

(0.32") Max. length between slots: depends on DRAM size Under favourable circumstances, a minimum ticket length down to 4 mm (0.16") could be used. It requires the sum of the copy length (b) and the detection slit height (e) to be larger than 7 mm (0.28"), that batch printing is used, and that no pull back of the paper is performed. Intermec does not guarantee that such short labels will work, but it is up to the user to test this in his unique application. c LSS Detection Position:

Five xed positions (distance from inner edge of paper):

3 mm (.118") 8 mm (.315") 12 mm (.472") 16 mm (.639") 20 mm (.787") d Detection Slit Length:

The length of the detection slit (excluding corner radii) must be minimum 2.5 mm (0.10") on either side of the LSS detection position (e). e Detection Slit Height:

Maximum:

Recommended:

Minimum:

Media Type Setup:

Ticket (w gaps) Do not allow any perforation to break the edge of the web, as this may cause the web to split, resulting in a paper jam. 21.3 mm 1.6 mm 1.2 mm

(0.83")

(0.06")

(0.05") 94 Intermec EasyCoder F4 Installation & Operation Ed. 2 Paper, cont'd. Tickets with Black Mark Appendix 2 Media Speci cations

(0.8")

(4.50")

(1.00")

(1.57") 114.3 mm 25.0 mm 40.0 mm 20.0 mm depends on DRAM size a Web Width:

Maximum:

Minimum (standard):

Minimum (Quick-Load):

b Copy Length:

Minimum:

Maximum:

c LSS Detection Position:

Five xed positions (distance from inner edge of paper):

3 mm (.118") 8 mm (.315") 12 mm (.472") 16 mm (.639") 20 mm (.787") d Black Mark Width:

The detectable width of the black mark should preferably be at least 5.0 mm (0.2") on either side of the LSS detection point. e Black Mark Length:

Maximum:

Common:

Minimum:

f Black Mark Y-Position:

It is recommended to place the black mark as close to the front edge of the ticket as possible and use a negative Stop Adjust value to control the paper feed, so the tickets can be properly torn or cut off. Media Type Setup:

Ticket (w mark) Important! Preprint that may interfere with the detection of the black mark should be avoided on the back of the paper. However, the LBLCOND statement allows the sensor to be temporarily disabled during a speci ed amount of paper feed in order to avoid unintentional detection, see Intermec Fingerprint manuals. The black mark should be non-re ective carbon black on a whitish background. Do not allow any perforations to break the edge of the web, as this may cause the web to split, resulting in a paper jam. 21.3 mm 12.5 mm 5.0 mm

(0.83")

(0.5")

(0.2") Intermec EasyCoder F4 Installation & Operation Ed. 2 95 Appendix 3 Interfaces RS 232C Interface The EasyCoder F4 has as standard two serial communication interfaces: RS 232C on "uart1:" and USB (see next page). Protocol Default setup:

Baudrate:

Char. length Parity:

Stop bits:

RTS/CTS ENQ/ACK:

XON/XOFF:

New Line:

To change the serial interface settings, see chapter 6 Setting Up the Printer. 9600 8 bits None 1 Disabled Disabled Disabled (both ways) CR/LF Interface Cable Computer end: DB-9 or DB-25 female connector (PC) Printer end:

DB-25 male connector Host Signal DB-9 DB-25 RXD TXD CTS RTS GND DSR 1 2 3 4 5 6 7 16 20 22 1 2 3 8 7 5 6 EasyCoder F4 Host Signal TXD RXD RTS CTS DSR

+ 5V1 DTR RI DB-25 DB-25 Signal shield RXD TXD CTS RTS DTR GND 1 3 2 5 4 20 7 6 DSR 1 2 3 4 5 6 7 16 20 22 Signal GND 1/. The external +5V is limited to 200 mA and is automatically turned off at overload. It is intended to drive e.g. an external alphanumeric keyboard connected to the RS 232C port.

"uart1:"

96 Intermec EasyCoder F4 Installation & Operation Ed. 2 USB Interface USB = Universal Serial Bus The EasyCoder F4 has as standard one USB communication port. To use the USB interface for printing from a PC, you need a special USB printer driver installed in your PC. Using an USB Class A - B cable, connect the Class A end to your PC or hub and the Class B end to your EasyCoder F4 printer. Appendix 3 Interfaces USB Class A connector. Connect to PC or hub. USB USB Class B connector. Connect to USB receptacle on the printer's rear plate. Note:

The USB interface is presently not supported by the Intermec Fingerprint rmware (v. 7.31). Intermec EasyCoder F4 Installation & Operation Ed. 2 97 Appendix 3 Interfaces Double Serial Interface Board

"uart2:"

1/. Intermec Shell either auto-

matically sets the correct std IN and OUT port when an applica-

tion is selected, e.g. a Windows driver, or prompts you to select one, see chapter 8. The EasyCoder F4 can optionally be tted with an extra double serial interface board, which provides the printer with two more serial ports; "uart2:" and "uart3:". These ports can be con gured for various types of serial communication in combination according to the customer's request. Use the Intermec Fingerprint instruction SETSTDIO to select standard IN and OUT ports (by default "uart1:"

is both std IN and OUT port)1.

"uart2:"

RS 232C RS 422 Non-isolated RS 422 Isolated RS 485

"uart3:"

RS 232C RS 422 Non-isolated 20 mA Current Loop Description Not connected RS 232 Transmitter RS 232 Receiver RS 232 Request To Send RS 232 Clear To Send RS 232 Data Set Ready Ground Not connected

+RS 422 Receive 5 Volt for external use (max. 200 mA)1

-RS 422 Receive Not connected

"uart2:" Serial Port The communication ports "uart2:" uses a female DB 25 connector. Pin 1 2 3 4 5 6 7 814 15 16 17 18 19 20 21 22 23 2425 Signal Name TxD RxD RTS CTS DSR GND

+RS422I

+5V

-RS422I

+RS422O/+RS485 +RS 422 Transmit/+RS 485 RS 232 Data Terminal Ready DTR

-RS 422 Transmit/-RS 485

-RS422O/-RS485 RI RS 232 Ring Indicator Optional shield for RS 422 and RS 485 Shield Not connected 1/. The external 5V is automatically turned off at overload. 98 Intermec EasyCoder F4 Installation & Operation Ed. 2 Double Serial Interface Board, cont'd.

"uart3:"

Appendix 3 Interfaces Description Not connected RS 232 Transmitter RS 232 Receiver RS 232 Request To Send RS 232 Clear To Send RS 232 Data Set Ready Ground Not connected

+20 mA current loop

-20 mA current loop

+TXD 20 mA current loop

-TXD 20 mA current loop

+20 mA current loop

(printer active receiver)

-20 mA current loop

(printer active receiver)

+RS 422 Receive 5 Volt for external use (max. 200 mA)1

-RS 422 Receive

+TXD 20 mA current loop

"uart3:" Serial Port The communication ports "uart3:" uses a male DB 25 connector. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Signal Name TxD RxD RTS CTS DSR GND

+20M1

-20M1

+TXD

-TXD

+20M2

-20M2

+RS422I

+5V

-RS422I

+RxD

+RS422O/+RS485 +RS 422 Transmit/+RS 485 RS 232 Data Terminal Ready DTR

-RS 422 Transmit/-RS 485

-RS422O/-RS485 RS 232 Ring Indicator RI Shield Optional shield for RS 422 and RS 485 Not connected

-RxD

-TXD 20 mA current loop 1/. The external 5V is automatically turned off at overload. Intermec EasyCoder F4 Installation & Operation Ed. 2 99 Appendix 3 Interfaces IEEE 1284 Parallel Interface Board The EasyCoder F4 can optionally be tted with an IEEE 1284-I compatible parallel interface board1. The parallel port is addressed in Intermec Fingerprint as device "centronics:". Select "centronics:"

as standard IN port by means of the instruction SETSTDIO (by default, "uart1:" in std IN port)2. Interface Cable Connectors Computer end: Depends on type of host computer. Printer end:

36 pin female IEEE 1284B Centron Pin 1 29 10 11 12 13 14 15 16 17 18 1930 31 32 33-35 36 Signal Name DStrobe Data 07 Ack Busy PE Select AF Not connected Ground Screen

+5V Ext GND Init Error Not connected Selectin

"centronics:"

1/. Nibble, byte, ECP and EPP from printer to host are presently not supported. 2/. Intermec Shell either auto-

matically sets the correct std IN and OUT port when an applica-

tion is selected, e.g. a Windows driver, or prompts you to select one, see chapter 8. 100 Intermec EasyCoder F4 Installation & Operation Ed. 2 Industrial Interface Board Appendix 3 Interfaces The EasyCoder F4 can optionally be fitted with an Industrial Interface Board, that provides the printer with one extra serial communication port ("uart2:"), which can be con gured for one of the following alternatives RS 232C RS 422 Non-isolated RS 422 Isolated RS 485 This port is identical to "uart2:" on the double serial interface board. The Industrial Interface Board also has a female DB-44 connector with... 8 digital IN ports with optocouplers 8 digital OUT ports with optocouplers 4 OUT ports with relays. Refer to the installation instructions for the Industrial Interface Board for further information. Industrial Interface

"uart2:"

Intermec EasyCoder F4 Installation & Operation Ed. 2 101 Appendix 3 Interfaces EasyLAN 100i Interface Board The Intermec EasyLAN 100i Ethernet interface board provides the printer with a 10BaseT Ethernet or 100BaseTX Fast Ethernet network connection. You can communicate with the printer via a LAN (Local Area Network) or provide the printer with its own home page, so you can reach the printer via internet on the world wide web (www). EasyLAN 100i supports most major computer systems and environ-

ments. You can assign passwords to restrict both login and printer access. The internal EasyLAN 100i web pages allow you to con-

tinuously monitor printer status and to upgrade the ash memory of the printer when new rmware becomes available. EasyLAN 100i supports SNMP for remote monitoring. When an EasyLAN 100i interface board is tted in the printer, some extra menus will be added to the Setup Mode (see chapter 7 Setup Mode). The Ethernet port is addressed in Intermec Fingerprint 7.3 or later as device "net1:" (communication channel 5). RJ-45 connector 102 Intermec EasyCoder F4 Installation & Operation Ed. 2 Appendix 4 EasySet Bar Code Wand Setup Connection and Operation 1. Connect the optional EasySet bar code wand to the receptacle on the printers rear plate. 2. Read the appropriate bar code to set up the printer. Hold the wand like a pencil and move it rather swiftly across the bar code. Connect here!

3. When the bar code has been accepted, the printer emits a short beep and the Ready control lamp on the printers front blinks brie y. 4. This manual only contains a selection of setup options. For information on how to produce your own setup bar codes, please refer to the Intermec Fingerprint 7.31 Reference Manual. Intermec EasyCoder F4 Installation & Operation Ed. 2 103 Appendix 4 EasySet Bar Code Wand Setup Serial Communication on "uart1:"

Baudrate Char. Length Parity 104 Intermec EasyCoder F4 Installation & Operation Ed. 2 Appendix 4 EasySet Bar Code Wand Setup Serial Communication on "uart1:", cont'd. No. of Stop Bits Reset comm. to default RTS/CTS ENQ/ACK XON/XOFF, Data to Host Intermec EasyCoder F4 Installation & Operation Ed. 2 105 Appendix 4 EasySet Bar Code Wand Setup Serial Communication on uart1:, contd. XON/XOFF, Data from Host New Line Start- and Stopadjust Tear Off Peel Off Default 106 Intermec EasyCoder F4 Installation & Operation Ed. 2 Contrast Appendix 4 EasySet Bar Code Wand Setup Intermec EasyCoder F4 Installation & Operation Ed. 2 107 Appendix 4 EasySet Bar Code Wand Setup Test Labels Media Width 108 Intermec EasyCoder F4 Installation & Operation Ed. 2 Media Length Appendix 4 EasySet Bar Code Wand Setup Intermec EasyCoder F4 Installation & Operation Ed. 2 109 Appendix 4 EasySet Bar Code Wand Setup Media Type Print Speed 110 Intermec EasyCoder F4 Installation & Operation Ed. 2 Appendix 4 EasySet Bar Code Wand Setup Paper Type Direct Thermal Printing (Europe) Direct Thermal Printing (USA) Intermec EasyCoder F4 Installation & Operation Ed. 2 111 RFID Module Appendix 5 RFID Module The EasyCoder F4 can optionally be fitted with an Intellitag 500 RFID (radio frequency identification) board that provides the printer with the means to pre-

program Intellitag 500 RFID SmartLabels when the bar code portion of the label is printed. The RFID board is addressed in Intermec Fingerprint 7.3 or later as device uart2:

The RFID board does not require connection to any device external to the printer. The RFID module is fitted in the printer in the space allocated for optional interface boards and therefore cannot be used in conjuction with, or in addition to, any of the optional interface boards. Refer to the installation instructions for the RFID Option Board for further information. Chassis location for RFID module 112 Intermec EasyCoder F4 Installation & Operation Ed. 2 Notes Intermec EasyCoder F4 Installation & Operation Ed. 2 113