FCC ID: ANO20040501CX2 Model: WM3B2200BG(WLAN 802.11bg Adapter)

FCC Test Report (Class II), FCC ID: ANO20040501CX2 Document Number: FCC 19-0290-0 Users Manual

(Transmitter Operating Instructions) The applying LMA transmitter device is an easy access adapter for users with plug and play structure, so users dont have to take care for any special operation. The instructions shown from the next page are the only ones provided to users that are displayed on LCD screen of the host PC

(ThinkPad X41 Tablet Series). Prepared by T. Murota Wireless connections 1/1 Wireless connections You can connect to the Internet without connecting a wire to your computer by setting up a wireless access point or residential gateway. A wireless access point does not connect you to the Internet directly. Instead, it connects to a wired connection such as a cable modem, a DSL modem, or a phone line. Certain wireless technologies are being used to connect to an access point. Wireless LAN (the IEEE 802.11 standard) and Bluetooth technologies work similarly for wireless networking. To connect to an access point, you will need several pieces of information. You will need to know the network name (obtain this from your administrator), and your MAC address (which should have come with your computer or wireless networking card). You may also need to set up encryption. Contact your administrator for your network name and encryption settings. You may need to register your MAC address with your network administrator before connecting to your company network. A residential gateway is the consumer version of an access point. Consult your residential gateway instructions for setup. Be careful to disable the wireless function when you are not using it because it uses power even when you are not connected to the network. Some models have an integrated Wireless LAN and/or Bluetooth antenna and hardware. If your computer did not come with integrated wireless, you can purchase a PC Card as an option. Wireless LAN gives you a high-speed connection to an access point. If your computer comes with the built-in wireless networking card, refer to Making wireless LAN connections for more information. mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/wireless.h... 2005/04/15 Making wireless LAN connections 1/1 Making wireless LAN connections You can stay connected to your network while you are in the office, in a meeting room, or at home, with no need for a wired connection. Some ThinkPad(R) models come with a built-in wireless networking card and a configuration utility to help you make wireless connections and monitor the status of your connection. Attention: If you carry your ThinkPad computer with the wireless LAN feature into an airplane, you need to disable it before boarding. To disable it, refer to the instructions in Enabling or disabling the wireless feature. Wireless networking setup Wireless security features Checking wireless connection status Enabling or disabling the wireless feature Wireless upgradeable ThinkPad models Note: Some models come with a wireless networking card and a wireless LAN configuration utility built-in. If your computer does not come with these features, you can purchase the wireless networking card as an option. For more information, refer to Finding options from IBM. Note: If you use the computer in tablet mode, do not cover the UltraConnect(TM) wireless antennas built into the display. mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/wireconn. .. 2005/04/15 Wireless networking setup 1/1 Wireless networking setup To use the built-in wireless networking card (the IEEE 802.11 standard) to communicate, click this button to start IBM(R) Access Connections, and follow the instructions on the screen. Note: Before you start setting up wireless networking connections by using Access Connections, obtain a Network Name

(SSID) and your encryption information from your network administrator. IBM Access Connections, a connectivity assistant program, can easily enable one network adapter and disable the other adapters on demand. After setting up your wireless networking connection, you can use the program to quickly switch the network settings. mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/wireset.htm 2005/04/15 Wireless security features 1/1 Wireless security features Advances in wireless technology require that we manage your security more reliably than ever. Therefore, IBM has extended its IBM Embedded Security Subsystem to encompass virtually all of our ThinkPad(R) and desktop computer lines. This security subsystem helps protect data, hardware, network access and communications - both wired and wireless - on select ThinkPad and desktop PCs. The IBM Embedded Security Subsystem provides hardware-based protection of critical security information, including passwords, encryption keys, and electronic credentials. It also helps identify computer users involved in transactions, and helps establish that data transmissions are authentic, confidential and intact. IBM Security and Privacy Services for wireless risk assessment and wireless solution design can help you assess the risks based on your business needs, identify your information risk position, and integrate security strategies, policies, and architectures to help you achieve your wireless e-business objectives. To effectively manage risk on an ongoing basis, organizations must have a sound security strategy. By understanding threats and vulnerabilities at an early stage, we can help define the necessary scope and features of your wireless e-business security infrastructure. For more information on IBM's wireless security offerings, click the following link:

http://www.pc.ibm.com/us/think/thinkvantagetech/security.html mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/wiresec.H... 2005/04/15 Checking wireless connection status 1/1 Checking wireless connection status You can check the signal strength and status of your wireless connection either by opening IBM Access Connections, or by double-

clicking the IBM Access Connections wireless status icon in the system tray. The Access Connections wireless status icon displays the signal strength and status of your wireless connection as follows:

No link or a very poor one Usable but weak link Strong link Wireless radio is disabled Note: If you have trouble in making a connection, try moving your computer closer to your wireless access point. See Also mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/wirestat.h... 2005/04/15 Enabling or disabling the wireless feature 1/1 Enabling or disabling the wireless feature To enable or disable the wireless feature, press Fn+F5. A list of wireless devices appears in the Wireless Radio Control window. You can turn the feature on and off with a single click. You can also enable or disable the feature by the following procedures. To enable the wireless feature, do as follows:

1. Click the Access Connections wireless icon in the system tray. 2. Click Turn Wireless Radio On. To disable the wireless feature, do as follows:

1. Click the Access Connections wireless icon in the system tray. 2. Click Turn Wireless Radio Off. Note: You can also use the Tablet Shortcut Menu to enable or disable the wireless feature if you are using your computer in tablet mode. Note: To use the Access Connections wireless icon or the Fn+F5 key combination for enabling or disabling the wireless feature, select Enabled for the Internal Wireless Device in the BIOS Setup Utility. If you have selected Radio off, neither the Access Connections wireless icon nor the Fn+F5 key combination for the wireless radio control will work. mk:@MSITStore:C:DOCUME1tmurotaLOCALS1TempnotesE1EF34WIRELESS.CHM::/Wlenab.htm 2005/04/15 Wireless upgradeable ThinkPad models Depending on the model, your ThinkPad(R) computer might be wireless upgradeable. This means that your computer has an antenna that can support wireless LAN access when wireless LAN access points are available. Wireless devices are available from IBM: Finding options from IBM. Installing the software in Windows XP and Windows 2000 To use an option Card with your ThinkPad computer, first you need to install the software necessary to run it. Do the following:

1. Start your operating system. Log on with a user ID authorized as an administrator. 2. Insert the Installation CD into the CD-ROM or DVD drive of your ThinkPad computer. The Welcome screen appears. 3. Click Next. The Select Packages screen appears. 4. The program detects if any of the software components have already been installed. All listed components are selected automatically if none of the components have been installed already. If you clear any of the check boxes on the menu screen, the corresponding components will not be installed. 5. Click Next, and follow the instructions on the screen. After you have installed the software, you need to configure wireless network connection. Start the IBM Access Connections and follow the instructions on the screen.

FCC Test Report (Class II), FCC ID: ANO20040501CX2 Document Number: FCC 19-0290-0 Users Manual The attachment is the part of the users manual of the specific host device (IBM ThinkPad X41 Tablet Series) that indicates the regulatory notices concerning the FCC Part 15 and IC RSS-210/102. Prepared by T. Murota ThinkPad X41 Tablet Series Regulatory Notice First Edition (March 2005) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law:

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimers or express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements or changes in the products or the programs described in this publication at any time. It is possible that this publication may contain reference to, or information about, IBM products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that IBM intends to announce such IBM products, programming, or services in your country. Requests for technical information about IBM products should be made to your IBM authorized dealer or your IBM marketing representative. Copyright International Business Machines Corporation 2005. All rights reserved. US Government Users Restricted Rights Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp. Contents Read first regulatory information . USA Federal Communications

. Commission (FCC) . Canada Industry Canada (IC)

. 1

. 3

. 9

. Other countries

. Notice for users in Australia

. Notice for users in Brazil . Notice for users in India . Notice for users in Korea . Notice for users in New Zealand Notice for users in Singapore

. Electronic emission notices . Telecommunication notices

. Industry Canada requirements

. 15

. 17

. 19 Trademarks . 21

. 21

. 21

. 21

. 22

. 22

. 25

. 27 Copyright IBM Corp. 2005 iii iv ThinkPad X41 Tablet Series Regulatory Notice Read first regulatory information Regulatory notice for ThinkPad X41 Tablet Series This notice is a supplementary document of the ThinkPad X41 Tablet Series Service and Troubleshooting Guide. Please read this document before you use the ThinkPad X41 Tablet Series computer. The ThinkPad X41 Tablet Series computer complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. You must install and use your ThinkPad computer in strict accordance with the instructions as described hereafter. Avis de rglementation pour les ThinkPad X41 Tablet Series Le prsent avis est un document qui vient complter le Guide de maintenance et didentification des incidents ThinkPad X41 Tablet Series. Veuillez lire ce document avant dutiliser lordinateur ThinkPad X41 Tablet Series. Lordinateur ThinkPad X41 Tablet Series est conforme aux normes de scurit et de radiofrquence du pays ou de la rgion o son utilisation sans fil est agre. Vous devez installer et utiliser votre ordinateur ThinkPad en respectant scrupuleusement les instructions dcrites ci-aprs. Copyright IBM Corp. 2005 1 2 ThinkPad X41 Tablet Series Regulatory Notice USA Federal Communications Commission (FCC) I) Radio Frequency interference requirements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. An improper installation or unauthorized use may cause harmful interference to radio communications. Also, unauthorized changes or modifications could void the user's authority to operate the equipment. Refer to the Electronic emission notices on page 15 for more detail. i) Radio communication functions Wireless LAN Mini-PCI Cards marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). When you use the models AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) or WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter):

v This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. v High power radar are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. ii) Radio digitizer function in LCD screen The ThinkPad X41 Tablet Series computers employ a radio digitizer function in LCD screen which is able to sense the Tablet Digitizer Pen shipped associated with your computer. The digitizer emits extra low power radio frequency and complies with the FCC Part 15, Subpart C. The FCC ID: ANOX41T is indicated on the label at the bottom side of your ThinkPad computer. Copyright IBM Corp. 2005 3 II) Installation of wireless modules User installable wireless modules v Mini-PCI Cards FCC ID: ANO20040501CX2, Model: WM3B2200BG (Intel PRO/Wireless 2200BG Mini-PCI Adapter from IBM) FCC ID: ANO20040601CX2, Model: WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter) FCC ID: ANO20040600BTL, Model: AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) v Communication Daughter Card (CDC) FCC ID: ANO20040700HER, Model: J07M067 (IBM Integrated Bluetooth IV with 56K Modem) i) FCC ID of wireless modules There is no FCC ID for Mini-PCI Cards shown on the enclosure of your ThinkPad computer. Instead you will find an indicator pointing to the location of the FCC ID on the bottom side of your ThinkPad computer as shown in the figure i-1). Also the location of the FCC IDs indicator for CDC is shown in the figure i-2). The FCC IDs are affixed on each approved module installed in the Mini-PCI Card slot or the CDC slot. i-1) Mini-PCI Cards:

FCC ID: ANO20040501CX2, Model: WM3B2200BG FCC ID: ANO20040601CX2, Model: WM3B2915ABG FCC ID: ANO20040600BTL, Model: AR5BMB-44 4 ThinkPad X41 Tablet Series Regulatory Notice TX FCC ID for an installed transmitter card located under this Customer Access Panel i-2) CDC FCC ID: ANO20040700HER, Model: J07M067 USA Federal Communications Commission (FCC) 5 TX FCC ID for an installed CDC transmitter card located under this Customer Access Panel ii) Installation of approved wireless modules If no integrated wireless LAN Mini-PCI Card or RF CDC module has been preinstalled in your ThinkPad computer, you can install one, provided by IBM as an option. Plug the wireless card option into the Mini-PCI Card slot or CDC slot located under the expansion slot cover of your ThinkPad computer as shown below. 6 ThinkPad X41 Tablet Series Regulatory Notice Attention: The ThinkPad X41 Tablet Series computer contains an authentication mechanism If you install an unauthorized wireless LAN Mini-PCI Card or RF CDC module that is not approved for use in the ThinkPad X41 Tablet Series computer, the computer will not start, but only displays an error message and emits beeps. III) RF safety compliance The antennas used for wireless LAN adapters in this notebook computer are located at the upper edge of the LCD screen, and the antenna used for Bluetooth card (Model: J07M067) is located at the left side lower edge of the LCD screen. The total radiated energy from those antennas connected to one of the wireless LAN Mini-PCI adapters and Bluetooth card (Model: J07M067) conforms to the FCC limit of SAR

(Specific Absorption Rate) requirement regarding CFR Part 2 section 1093. The maximum SAR values measured for the ThinkPad X41 Tablet Series computer are 0.697W/Kg for model AR5BMB-44, 0.884W/Kg for model WM3B2915ABG, and 1.01W/Kg for model WM3B2200BG. (The limit is 1.6W/Kg.) USA Federal Communications Commission (FCC) 7 IV) Use of wireless options Your ThinkPad computer is approved for use of one of the granted Wireless LAN Mini-PCI Cards together with the granted Bluetooth module (FCC ID: ANO20040700HER) in the CDC slot simultaneously. Make sure of the following conditions on use of these wireless features. 1. When you use any other RF option device than the Mini-PCI or CDC card, you are requested to confirm that the device conforms to the SAR requirement and is approved to use for ThinkPad X41 Tablet Series computer. 2. All other wireless features including the integrated Wireless LAN Mini-PCI Card and Bluetooth transmitter in your ThinkPad computer are required to be turned off. 3. Users must follow the RF Safety instructions on wireless option devices that are included in the RF option devices users manual. 8 ThinkPad X41 Tablet Series Regulatory Notice Canada Industry Canada (IC) I) Installation of wireless modules User installable wireless modules v Mini-PCI Cards IC: 349E-WM3B22BG, Model: WM3B2200BG (Intel PRO/Wireless 2200BG Mini-PCI Adapter from IBM) IC: 349E-WM3B29AG, Model: WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter) IC: 349E-AR5BMB44, Model: AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) v Communication Daughter Card (CDC) IC: 349E-J07M067, Model: J07M067 (IBM Integrated Bluetooth IV with 56K Modem) The certification number of Industry Canada for each approved Mini-PCI wireless card or RF Communication Daughter Card (CDC) is affixed on each module installed in the Mini-PCI Card slot or the CDC slot as shown below. If no integrated wireless LAN Mini-PCI Card or RF CDC module has been preinstalled in your ThinkPad computer, you can install one, provided by IBM as an option. Plug the wireless card option into the Mini-PCI Card slot or CDC slot located under the expansion slot cover of your ThinkPad computer. Wireless LAN Mini-PCI Cards marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). Copyright IBM Corp. 2005 9 Attention: The ThinkPad X41 Tablet Series computer contains an authentication mechanism You can install or remove each wireless feature by yourself. If you install an unauthorized wireless adapter that is not approved for use in the ThinkPad X41 Tablet Series computer, the computer will not start, but only displays an error message and emits beeps. II) Low power license-exempt radiocommunication devices (RSS-210) Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. 10 ThinkPad X41 Tablet Series Regulatory Notice i) Radio communication functions When you use the model AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) or WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter):

v The device for the band 51505250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems. v High power radars are allocated as primary users (meaning they have priority) of 52505350 MHz and 56505850 MHz and these radars could cause interference and/or damage to LELAN

(Licence-Exempt Local Area Network) devices. ii) Radio digitizer function in LCD screen The ThinkPad X41 Tablet Series computers employ a radio digitizer function in LCD screen which is able to sense the Tablet Digitizer Pen shipped associated with your computer. The digitizer emits extra low power radio frequency and complies with the standard (RSS-210). The IC certification number IC:

349E-X41T is indicated on the label at the bottom side of your ThinkPad computer. III) Exposure of humans to RF fields (RSS-102) ThinkPad X41 Tablet Series computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canadas Web site at www.hc-sc.gc.ca/rpb The antennas used for wireless LAN adapters in this notebook computer are located at the upper edge of the LCD screen, and the antenna used for Bluetooth card (Model: J07M067) is located at the left side lower edge of the LCD screen. The total radiated energy from those antennas connected to one of the wireless LAN Mini-PCI adapters and Bluetooth card (Model: J07M067) conforms to the IC limit of SAR

(Specific Absorption Rate) requirement regarding RSS102 section 3. The maximum SAR values measured for the ThinkPad X41 Tablet Series computer are 0.697W/Kg for model AR5BMB-44, 0.884W/Kg for model WM3B2915ABG, and 1.01W/Kg for model WM3B2200BG. (The limit is 1.6W/Kg.) Numro dhomologation Canada Industry Canada (IC) 11 Le numro dhomologation dIndustrie Canada pour chaque carte Mini-PCI sans fil homologue ou carte RF CDC (Communication Daughter Card) est indiqu sur chaque module install dans lemplacement Mini-PCI Card ou CDC comme illustr ci-dessous. Les cartes sans fil applicables sont les suivantes:

v IC: 349E-WM3B22BG, Model: WM3B2200BG (Intel PRO/Wireless 2200BG Mini-PCI Adapter from IBM) IC: 349E-AR5BMB44, Model: AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) IC:349E-WM3B29AG, Model: WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter) IC: 349E-J07M067, Model: J07M067 (IBM Integrated Bluetooth IV with 56K Modem) v v v Les cartes de rseau local sans fil mini-PCI commercialises aux Etats-Unis et au Canada ne prennent pas en charge les canaux tendus (12ch, 13ch) et ne fonctionnent donc pas sur de tels canaux. Attention: Lordinateur ThinkPad X41 Tablet Series contient un mcanisme dauthentification. Vous pouvez installer ou dsinstaller tout dispositif sans fil. Si vous installez une carte sans fil qui nest pas homologue pour lordinateur ThinkPad X41 Tablet Series, lordinateur ne dmarrera pas; un message derreur sera affich et des bips sonores seront mis. 12 ThinkPad X41 Tablet Series Regulatory Notice Remarque relative aux appareils de communication radio de faible puissance sans licence

(CNR-210) Le fonctionnement de ce type dappareil est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas perturber les communications radio, et 2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son dysfonctionnement. Lorsque vous utilisez le modle AR5BMB-44 (IBM 11a/b/g Wireless LAN Mini PCI Adapter II) ou WM3B2915ABG (Intel Pro/Wireless 2915ABG mini-PCI Adapter):

v Tout appareil destin la bande 5150-5250 MHz devra tre exclusivement utilis en intrieur afin de rduire les risques de perturbations lectromagntiques gnantes sur les systmes de satellite mobile dans un mme canal. v Les radars forte puissance sont dsigns comme les utilisateurs principaux (cest--dire quils sont prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz. Ils peuvent provoquer des perturbations lectromagntiques sur les appareils de type LELAN (rseau de communication local sans licence) ou les endommager. Exposition des tres humains aux champs radiolectriques (RF) (CNR-102) Le ThinkPad X41 Tablet Series utilise des antennes intgrales faible gain qui nmettent pas un champ lectromagntique suprieur aux normes imposes par le Ministre de la sant canadien pour la population. Consultez le Safety Code 6 sur le site Web du Ministre de la sant canadien ladresse www.hc-sc.gc.ca/rpb. Canada Industry Canada (IC) 13 14 ThinkPad X41 Tablet Series Regulatory Notice Electronic emission notices Federal Communications Commission (FCC) Statement v v v v v ThinkPad X41 Tablet Series (Machine Type: 1866, 1867, 1868 and 1869) Intel PRO/Wireless 2200BG Mini-PCI Adapter from IBM Intel Pro/Wireless 2915ABG mini-PCI Adapter IBM 11a/b/g Wireless LAN Mini PCI Adapter II IBM Integrated Bluetooth IV with 56K Modem This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

v Reorient or relocate the receiving antenna. v v Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. v Consult an IBM authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the userfs authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Copyright IBM Corp. 2005 15 International Business Machines Corporation New Orchard Road Armonk, NY 10504 Telephone 1-919-543-2193 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Industry Canada Class B Emission Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Avis de conformit la rglementation dIndustrie Canada Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. European Community Directive Conformance Statement This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electro-magnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards. This product satisfies the Class B limits of EN 55022. 16 ThinkPad X41 Tablet Series Regulatory Notice Telecommunication notices Federal Communications Commission (FCC) and Telephone Company Requirements (Part 68 of the FCC Rules) 1. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent, and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your computer, you should be sure to follow the installation instructions for your fax software package. 2. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. 3. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). If the built-in modem causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But, if advance notice isnt practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC. 4. 5. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain uninterrupted service. If you experience trouble with this built-in modem, contact your IBM Authorized Seller, or the IBM Corporation, 500 Columbus Avenue, Thornwood, NY 10594, 1-800-772-2227, for repair/warranty information. The telephone company may ask you to disconnect this equipment from 6. Copyright IBM Corp. 2005 17 the network until the problem has been corrected, or until you are sure the equipment is not malfunctioning. 7. No customer repairs are possible to the modem. If you experience trouble with this equipment, contact your Authorized Seller or the IBM Corporation for information. 8. The modem may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Contact your state public utility commission or corporation commission for information. 9. When ordering network interface (NI) service from the Local Exchange Carrier, specify service arrangement USOC RJ11C. 10. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this Data/Fax Modem does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. 11. 12. The software contained in this Data/Fax Modem to allow user access to the network must be upgraded to recognize newly established network area codes and exchange codes as they are placed into service. 18 ThinkPad X41 Tablet Series Regulatory Notice Industry Canada requirements Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of communication. In some cases, the companys inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs of alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalence Number (REN) for the terminal equipment J07M070 is 0.0. The Ringer Equivalence Number (REN) for the terminal equipment J07M067 is 0.5. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. Copyright IBM Corp. 2005 19 Avis Le prsent matriel est conforme aux spcifications techniques dIndustrie Canada applicables au matriel terminal. Cette conformit est confirme par le numro denregistrement. Le sigle IC, plac devant le numro denregistrement, signifie que lenregistrement sest effectu conformment une dclaration de conformit et indique que les spcifications techniques dIndustrie Canada ont t respectes. Il nimplique pas quIndustrie Canada a approuv le matriel. Avant dinstaller ce matriel, lutilisateur doit sassurer quil est permis de le raccorder aux installations de lentreprise locale de tlcommunication. Le matriel doit galement tre install en suivant une mthode accepte de raccordement. Dans certains cas, les fils intrieurs de lentreprise utiliss pour un service individuel ligne unique peuvent tre prolongs au moyen dun dispositif homologu de raccordement (cordon prolongateur tlphonique interne). Labonn ne doit pas oublier quil est possible que la conformit aux conditions nonces ci-dessus nempechent pas la dgradation du service dans certaines situations. Actuellement, les entreprises de tlcommunication ne permettent pas que lon raccorde leur matriel des jacks dabonn, sauf dans les cas prcis prvus par les tarifs paticuliers de ces entreprises. Les rparations de matriel homologu doivent tre effectues par un centre dentretien canadien autoris dsign par le fournisseur. La compagnie de tlcommunications peut demander lutilisateur de dbrancher un appareil la suite de rparations ou de modifications effectues par lutilisateur ou cause de mauvais fonctionnement. Pour sa propre protection, lutilisateur doit sassurer que tous les fils de mise la terre de la source dnergie lectrique, des lignes tlphoniques et des canalisations deau mtalliques, sil y en a, sont raccords ensemble. Cette prcaution est particulirement importante dans les rgions rurales. Avertissement Lutilisateur ne doit pas tenter de faire ces raccordements lui-mme; il doit avoir recours un service dinspection des installations lectriques, ou lectricien, selon le cas. Lindice dquivalence de la sonnerie (IES) du prsent matriel J07M070 est de 0.0. Lindice dquivalence de la sonnerie (IES) du prsent matriel J07M067 est de 0.5. LIES assign chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent tre raccords une interface tlphonique. La terminaison dune interface peut consister en une combinaison quelconque de dispositifs, la seule condition que la somme dindices dquivalence de la sonnerie de tous les dispositifs nexcde pas 5. 20 ThinkPad X41 Tablet Series Regulatory Notice Other countries Notice for users in Australia For models: J07M070 and J07M067 The following notice applies when using the telephony functions:

WARNING: FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS COMPLIANCE LABEL. THIS INCLUDES CUSTOMER EQUIPMENT PREVIOUSLY LABELLED PERMITTED OR CERTIFIED. Notice for users in Brazil For models: J07M067, WM3B2200BG Portuguese English Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio This equipment is a secondary type device, that is, it is not protected against harmful interference, even if the interference is caused by a device of the same type, and it also cannot cause any interference to primary type devices. Notice for users in India For model: J07M067 The equipment type approval does not imply that the frequencies will be cleared automatically/operating licence will be granted as these are matters to be examined on case by case basis on the receipt of the application to WPC. For model: WM3B2200BG The WM3B2200BG equipment is typed approved in India for use of the IEEE 802.11b mode only in indoor applications. All other types of usages require specific wireless license from Wireless Planning & Coordination (WPC) Wing of Ministry of Communications and Information Technology of India Copyright IBM Corp. 2005 21 Before using the model WM3B2200BG, you must configure the device driver of your ThinkPad computer for 802.11b only operation. To disable 802.11g. follow the procedure below:

1. On your desktop, right-click the My Computer icon and select Properties. 2. Click the Hardware tab; then click the Device Manager button. 3. In the device list, expand Network Adapters, and then double-click Intel PRO/Wireless 2200BG Network Connection. 4. Click the Advanced tab. Then, from the Property list, select Wireless Mode . 5. Clear Use default value; from the drop-down box, select 802.11b only. 6. Click OK. Notice for users in Korea For models: J07M070 and J07M067 Please note that this device has been certified for residential use and may be used in any environment. For models: J07M067, WM3B2200BG, AR5BMB-44 Please note that this device has been certified for residential use and may be used in any environment. Notice for users in New Zealand Ambit J07M070 V.92 Data/Fax Modem: Telepermit No. PTC 211/03/081 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecoms network services. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. This warning typically applies to 56 kbit/s modems. 22 ThinkPad X41 Tablet Series Regulatory Notice This equipment may not provide for the effective hand-over of a call to another device connected to the same line. Some parameters required for compliance with Telecoms Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecoms specifications:

v There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and v The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next call attempt, and v Automatic calls to different numbers shall be spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another, and Incoming calls shall be answered between 3 and 30 seconds of receipt of ringing. v This equipment shall not be set up to make automatic calls to Telecoms 111 Emergency Service. The availability of the Modem on Hold feature is dependent on whether or not your Internet Service Provider and the Telecom network are connected to offer this feature. Any attempt to make use of Modem on Hold with this particular type of modem may work incorrectly due to the unequal sharing of the current fed to your line by this modem and the telephone you are using. No guarantees can be given as to the effectiveness of the Modem on Hold feature offered by this modem. Such problems are NOT a network fault and should not be reported to Telecom. Telecom can accept no liability for the mis-operation of the Modem on Hold facilities with devices of this type. Only modems Telepermitted in the PTC 218-series are recognised as being V.92 Modem on Hold capable. J07M067 56k Data/Fax Modem: Telepermit No. PTC 211/04/089 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecoms network services. Other countries 23 The Modem on Hold feature of V.92 modems requires compliance by the modem, the Public Switched Telephone Network (PSTN) and the Internet Service Provider (ISP). This modem may not handle Modem on Hold correctly when connected to the Telecom New Zealand PSTN even when it is loaded with the correct V.92 software. If problems occur with the operation of Modem on Hold do not report them to the Telecom Fault Service or a charge may be imposed on the customer. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. This condition typically applies to 56 kbit/s modems and facsimile machines operating at

>14.4 Kbit/s. This equipment may not provide for the effective hand-over of a call to another device connected to the same line. Under power failure conditions this appliance may not operate. Please ensure that a separate telephone, not dependent on local power, is available for emergency use. Some parameters required for compliance with Telecoms Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecoms Specifications:

1. There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next call attempt. 2. Automatic calls to different numbers shall be spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another. This equipment shall not be set up to make automatic calls to Telecoms 111 Emergency Service. In order to operate within the limits of compliance with Telecoms specifications, equipment shall be set to ensure that calls are answered within 30 seconds of the receipt of ringing. The facsimile rings to answer setting should be configured to a maximum of 10 rings to comply with this requirement. 24 ThinkPad X41 Tablet Series Regulatory Notice Notice for users in Singapore For models: J07M067, WM3B2200BG, AR5BMB-44 and WM3B2915ABG OPERATING CONDITIONS UNDER WHICH THE RADIOCOMMUNICATION EQUIPMENT ARE EXEMPTED FROM LICENSING To maximize frequency sharing while minimizing radio interference, the following operating conditions are imposed to confine the propagation of radio signals within a building or at a localised site:

a) The radiocommunication equipment shall be used for in-building or localised on-site operations;

b) The radiocommunication equipment shall operate at frequencies or frequency bands designated by IDA on non-exclusive basis;

c) The radiocommunication equipment shall not operate beyond the maximum permissible output power designated by IDA to confine the propagation of radio signals to a small localised area;

d) For an on-site localised operation with little obstruction by the nearby buildings or terrain, height of any external antenna, if installation approved by IDA, shall not be more than 10 metres above ground level to limit the radio wave propagation; and e) No repeater station shall be used to extend the radio coverage. Other countries 25 26 ThinkPad X41 Tablet Series Regulatory Notice Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both:

IBM IBM (logo) ThinkPad Intel is a trademark of Intel Corporation in the United States, other countries, or both. Other company, product, and service names may be trademarks or service marks of others. Copyright IBM Corp. 2005 27

Part Number: 39T2305 Printed in USA

(1P) P/N: 39T2305