FCC ID: 2ABFZ-ARC50-6WAP 11ac Wave2 Tri-band AP

User Manual of 11ac Wave2 Tri-band AP This is the user manual of 11ac Wave2 Tri-band AP, which will approximate guide you how to set and apply the Ceiling AP, it provide a convenient graphical interface for network construction and maintenance person, as well as a user through a simple and accurate operation, and configuration management of the ceiling wireless access point. 1 s t Hardware and Operation mode Instruction L E D i n d i c a t o r :

G r e e n : P o w e r I n d i c a t o r B l u e: W i F i I n d i c a t o r A P I n t e r f a c e :

RST: Reset Button, it make AP revert to default data after press it 15 seconds. WAN: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Wireless AP and WiFi Repeater operation mode LAN: Gigabit LAN Port to end users LED: LED Indicator of WAN port and LAN port DC: DC power connector AP installation:

Power Supply and working diagram:

1. Work at home:

If work at home, this device can be power by DC adapter or PoE adapter. Then access into IP address 192.168.188.253, switch to FAT AP mode and setup the SSID. User can choose gateway or AP operation mode based on their Internet environment and structure. P1 Working diagram 2. Work in business area:

This wireless AP work in most business area like hotel, school, hospital, shopping wall etc. In this application, it work in FIT AP mode, powered by PoE switch, managed by AC controller in centrally or remotely. The working diagram showed as follow:

P2 Working Diagram P3 Working Diagram Connect Wireless AP with PC:

Use can connect the PC with wireless AP by Wireless SSID and LAN cable:

The diagram of wireless connection showed as follow:

Pls note: the default SSID is WirelessAP2.4G/5.8G, SSIDs password is 66666666 P4. Wireless Connection The diagram of LAN cable connection showed as follow:

P5 Wired Connection 2ndLogin 1Connect the Ceiling AP with computer 255.255.255.0, follow P4 and P5 to finish. 2Configure the PCs local connection IP address as 192.168.188.X (X is number from 2 to 254), subnet mask is P5 Setting of computers IP address P 6 Setting of computers IP address 3) Input 192.168.188.253 into IE browser, then pop up the login page, the default login user name: Admin, Passwords: admin, pls do following P6 P7 Login 3rd : WEB GUI interface Setting:

1) Home After login, if default mode is FIT AP, then following device status will be showed:

In fit AP, user can configure the IP mode, reset and reboot this device. Other configurations is managed by AC P8 home controller in centrally. Click FIT AP, then switch to FAT AP. For the FAT AP, the login page showed as follow:

P7: Device Status FAT AP: Mean this AP in FAT mode now, click here to change to FIT AP if need. Pls note: FAT AP comply with SNMP protocol, can be configured through GUI interface or managed by SNMP controller. FIT AP comply with CAPWAP protocol, can be managed by CAPWAP controller. also. Operation mode: the default operation mode is AP; But in FAT AP, it support gateway, repeater, WISP operation mode In the above picture, showed in AP operation mode, CPU usage, AP location, LAN IP and Wi-Fi status. And it can view user Wi-Fi connection information after click user quantity:

P8 client list 2) Wizard operation mode one by one:

In FAT AP ,support Gateway, Repeater, WISP and AP operation mode, which can be set in Wizard. Lets show this P9 Wizard 2.1 Gateway mode Click Gateway mode, will ask for WAN settings, use choose the right internet mode based on their network structure, then click to continue. P10. WAN setting in Gateway Mode After configure the WAN setting, continue to Wi-Fi setting, including 2.4G Wi-Fi setting and 5G Wi-Fi setting:

In this part, mainly to set the SSID, channel, password, security... P11 Wireless Setting in Gateway Mode When click Next, then will complete the Gateway mode setting and show following picture, this AP will be reboot after click OK. P12 Complete the setting in Gateway Mode When return to Status, the page showed as follow:

P13 Status in Gateway Mode 2.2 WiFi Repeater mode be bridged, then next. Click WiFi Repeater operation mode in Wizard, then following page will pop up, scan the Wi-Fi and choose the SSID to P14 Repeater Mode After click Next button, then should configure the wireless setting as follow, then click Next to set SSID, password, channel, for broadcast 2.4G Wi-Fi and 5G Wi-Fi Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this P15 Wireless Setting in Repeater Mode data in this page if required. P16 Status in Repeater Mode Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on 2.3 WISP Operation mode:

the step showed in picture:

Configure the right WAN setting in WISP operation mode, then next. P17 WISP Mode P18 WAN setting in WISP mode Configure wireless data showed as follow, including 2.4G Wi-Fi and 5G Wi-Fi P19 Wireless Setting in WISP mode Then complete and back to status, will show the connection fail or success, then can configure the data based on request:

P20 Status in WISP mode 2.4 AP Operation mode:

For the AP mode, mainly from cable internet to Wi-Fi internet. And for this AP, user can set fixed IP address for AP in LAN setting, or make AP obtain the IP address from gateway or AC controller. If obtain the IP address from gateway, mean IP address will be same segment of gateway; And if obtain IP address from AC controller, should set IP segment in the address server in AC controller part. P21 LAN setting in AP Mode Click next in LAN setting, enter into wireless setting to set the SSID, password, channel, including 2.4G Wi-Fi and 5G Wi-Fi P22 Wireless Setting in AP Mode P23 Status in AP Mode 3) WiFi In WiFi setting, user can set SSID, channel, password, bandwidth for 2.4G wireless, 5.8G Wireless Lets Click WiFi in home page, will show return home, will show 2.4G WiFi, 5G WiFi, MAC ACL, WiFi Timer off and Advance:

For 2.4G WiFi, 5G WiFi, it is same configuration we showed in Wizard. In the above picture, we can find WiFi Analyzer: Mainly to analyze the APs signal strength in some channel, then make AP work in the channel with small quantity of AP, to avoid WiFi interference. P24 WiFi P25 Wireless Analyzer Virtural AP:

There are 3 virtual AP in 2.4G wireless, if need virtual SSID, then users can configure it showed in following picture:

Click VAP1 in 2G WIFI--Enable WiFi status--input SSID, password--Click Apple to enable multi-SSID for 2.4G WiFi. P26 Virtual AP MAC ACL: Mean MAC access control: allow or deny user access by MAC address. P27 MAC Access Control WiFi Timer Off: mean WiFi SSID will be off in the configured time. Enable WiFi time off, set WiFi off time, then apply to finish. P28 WiFi Timer Off Advanced Settings:

In this page, will show the region, RF Power, Max user access... P29 Advanced Setting Country Region: can choose China, USA, Brazil, UAE, ETSI, India. 2G mode: including 11n/g (40MHz), 11b/g(20MHz) 5G mode: including 11a(20MHz), 11an(40MHz), 11ac(80MHz) Multicast Fast: Default is off, but can choose 6M,9M, 12M, 18M, 24M, 36M, 54M Maximum for per AP: mean maximum user for each band. WLAN Partition: mean user isolation, default is disable. Short GI: data isolation, default is on. Coverage Threshold: The input data is signal strength that user connect with AP. The data is smaller, then mean user will connect with weak signal AP; the data is larger, mean user will connect to the stronger signal AP. Recommend to input -90dBm. max; Enhanced: 4dBm lower than efficient... TX Power: mean RF power is adjustable; Max mean the RF power showed in data sheet; Efficient: 4dBm lower than Preferred 5G: mean band steering, 5G priority. Enable it, then mobile phone will connect with 5G SSID in priority. DFS: special channel, most suit for USA, default is disable. 4.Network setting:

In this page, mainly to show the LAN setting, VLAN setting and cloud server setting. P30 Network Setting LAN Setting:

P31 WiFi Timer Off VLAN setting:

data from VLAN switch. Network--VLAN setting--ON- Input VLAN ID on SSID--Apply. This AP support tag VLAN based on SSID. Input VLAN ID in 2G SSID, then when user access into this SSID, it get P32 Tag VLAN Setting Cloud Server setting:

In this part, make AP access into cloud server for remote management. But make sure: A.the AP in Internet access already; B. Had registered ID from our cloud www.yowifi.net. P33 Cloud setting Management:

In this part, show the device backup, reboot, password modify, firmware upgrade and log. P34 Management Backup: Mean if you do some configure for this AP, then can save this configuration in file to computer. Next time if reset the AP, then restore this backup file to restore this AP with same configuration before reset. Reset default: mean restore to factory default settings, all configuration will be missed. Telnet: Enable this, mean can do engineer debug, but have risk in hacking. Reboot: Reboot the device immediately, or reboot the device in certain time. Can reboot everyday or every week. P35 Reboot Modify password: Modify WEB GUI login password, the default is admin. P36 Modify password Upgrade firmware: Mean upgrade new firmware for this wireless AP, but before upgrade, pls note: A. the device can upgrade the firmware in newest version, cant upgrade old version; B. dont power off the device when upgrade the firmware; C. Reset the AP after firmware upgrade. Time: Mean set system time for wireless AP. P37 Firmware Upgrade P38 Time Log:this is for AP working information, can export for problem recovery. P39 System info 4th Share Internet and Obtain IP address automatically Set computers TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed. the computer will obtain the IP address from router or base station to get Internet. P40 Fix IP. Tr o u b l e S h o o t i n g :

F 1 The Failure phenomenon and solution Failure phenomenon Solution SYS Indicator off Pls make sure the PoE module connection is right. POE Port connect with AP, LAN port connect with computer Pls check the IP address of computer and Wireless AP to see whether they are in same networking segment, The method is click start-Run inputcmdping 192.168.188.253 to test the Wireless AP connectivity. Reset Wireless AP and load it again;

Pls make sure the IP address 192.168.188.253 is not occupied by other device in Wireless APs networking;

Check computer and cable problem, recommend to use 10/100M UTP unshielded cable;

Clean up Arp binding from Start-Run inputcmd arp d Clean the IE Browers temporary files and Cache file Try to scan the avaliable wireless networking again Make sure the Wireless APs wireless standard11b/g/n, 2.4Gis correct The Security and passwords are matched between Wireless AP and AP The signal strength of AP is too weak to connect, should be more than -75dBm Scan it several times more Make sure there are 5G signal existed. Reset the Wireless AP, scan it again after Wireless AP restart Pls Check the computers IP address and DNS setting. If it is dynamin, set the network card as automatically obtain. If it is static IP, pls contact with ISP for correct IP address and DNS address. Press the Reset button more than 15 seconds after power on. The Wireless AP will restore factory default after the Wireless AP restart. Cant land to Wireless AP through Web page Wireless AP cant connect with AP

the status display unconnected Cant scan the wireless AP The connection of Wireless AP and AP is success, but the computer cant share internet How to Reset Wireless AP 20c

FCC ID LABEL:

Label Location Width:2cm FCC ID: 2ABFZ-ARC50-6WAP Product name: 11ac Wave2 Tri-band AP Model No.: ARC50-6WAP Long:4cm

International Communications Corporation Agent Authorization Company: International Communications Corporation Address:11801 Pierce St., 2nd FL Riverside, CA 92505, United States Product Name: 11ac Wave2 Tri-band AP Model Number(s): ARC50-6WAP Product Description: 11ac Wave2 Tri-band AP We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: Oct. 20, 2020 Name:

Keith M Alexis Title:

Dir. of Product Marketing Company:

International Communications Corporation

International Communications Corporation FCC Software Configuration Control Declaration Date: Oct. 20, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product: 11ac Wave2 Tri-band AP Model No.: ARC50-6WAP Regarding FCC Country Code Selection guidelines identified in KDB 594280 D01 v02r01. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Date: Oct. 20, 2020 Name:Keith M Alexis Title: Dir. of Product Marketing Signature of applicant FCC Software Configuration Control Declaration Rev1.0.docx

International Communications Corporation Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Oct. 20, 2020 Subject; Request for Confidentiality FCC ID: 2ABFZ-ARC50-6WAP To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description SOFTWARE SECURITY DESCRIPTION It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Keith M Alexis Title: Dir. of Product Marketing