INTELLIGENT SOLAR LED MOTION ACTIVATED FENCE LIGHT ITEM: SR51FB22C-08 INSTRUCTIONS FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE ON POSITION TO ALLOW THE RECHARGEABLE BATTERIES TO REACH MAXIMUM CAPACITY. The intelligent solar LED motion activated light measures the corresponding available battery power through the current voltage point of the battery, adjusts the energy and lumen output, and maximizes the lighting time. Tools Required INSTALLATION Hardware Included
(A) Screw X 4
(B) Wall Anchor X 4 Parts
(C) Light Fixture X 2
(D) Mounting Plate X 2 2.36in. x x Pencil Phillips-head Screwdriver Electric drill drill bit size:
7.5mm (3/10 in.) 1 Marking the location Mark the location where you want to mount the light fixture (Part C). Measure the width of two holes on the back of the solar fence light to align holes for the 2 screws (Part A) on the surface. The distance between the two holes is 2.36in. (60mm). Drill two holes. 2 Mounting the light Insert the wall anchors (Part B) so they are flush with the surface. Secure the mounting plate (Part D) in place with the screws (Part A). Mount the light on the mounting plate (Part D) by aligning the holes on the back of the light to the key on the front of the mounting plate. Slide and lock into place. B A D C NOTE: Light will stay on 30 seconds when triggered by motion. Detection range is 26 feet, detection angle is 120. Light use radio frequency technology to link, and should not be greater than 98 feet between the neighboring/adjacent lights. The package include 2 lights. These 2 lights is factory linked, and can not linked any other lights. TROUBLE SHOOTING If the light does not turn on, remove the battery cover and check if the battery pack is connected to the battery connector. If the connection is ok, replace the battery with a new one. REPLACING THE BATTERY Slide the power switch to the "OFF" position. Use a Phillips head screwdriver to remove the 6 screws holding the battery cover in place. Gently pull battery pack away from the light fixture and disconnect the battery connector. Replace old battery pack with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery pack. Connect the battery connector and insert battery pack into the light fixture. Replace the battery cover by aligning it properly and replacing the 6 screws removed earlier. Slide the power switch to the ON position. For optimum performance, allow light fixture to charge in full sunlight for 8-12 hours. Battery pack Power Switch Screws Battery Cover 02/28/2020 E INTELLIGENT SOLAR LED MOTION ACTIVATED FENCE LIGHT ITEM: SR51FB22C-08 FCC WARNING Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries . For additional help and information regarding installation, contact customer service at 1-844-551-0680, 8am-5pm, CST Monday Friday
, WESTINGHOUSE, are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved. customerservice@qx-usa.com 02/28/2020 2/2E SOLAR INTELIGENTE LED DE ILUMINACIN DE ACTIVADO POR MOVIMIENTO ITEM: SR51FB22C-08 INSTRUCCIONES PARA EL PRIMER USO: LA LUZ SOLAR NECESITA CARGARSE BAJO LUZ SOLAR DIRECTA POR UN PERIODO DE ENTRE 8 Y 12 HORAS CON EL INTERRUPTOR EN LA POSICIN "ON" (PRENDIDO) PARA PERMITIR QUE LAS BATERAS RECARGABLES ALCANCEN SU CAPACIDAD MXIMA. La luz inteligente activada por movimiento del LED solar mide la energa de la batera disponible correspondiente a travs del punto de voltaje actual de la batera, ajusta la energa y la salida de luz y maximiza el tiempo de iluminacin. Herramientas Necesarias INSTALACIN Herrajes Incluidos
(A) Tornillo X 4
(B) Anclajes de pared X 4 Taladro elctrico tamao de la broca de taladro: 7.5 mm (3/10 plg) Partes
(C) Lmpara X 2
(D) Base X 2 2.36in. x x Lpiz Cabeza de Phillips Destornillador 1 Cmo marcar el lugar de montaje Marque el lugar en el que quiere montar el artefacto de iluminacin
(Parte C). Mide el ancho de los dos orificios que estn en la parte posterior de la lmpara solar para cerca para alinearlos con 2 tornillos (Parte A) en la superficie. La distancia entre los orificios es de 2.36in. (60mm). Taladre dos orificios. 2 Cmo montar la lmpara Inserta los anclajes de pared (Parte B) de manera que queden al ras de la superficie. Fije la placa de montaje (Parte D) en su sitio con los tornillos (Parte A). Monte la luz en la placa de montaje (Parte D) alineando los orificios de la parte posterior de la luz con la llave en la parte frontal de la placa de montaje. Deslice y encaje en su sitio. NOTA: cuando la luz se active con un movimiento, permanecer encendida durante 30 segundos. El rango de deteccin es de 26 pies (unos 8 metros), el ngulo de deteccin es de 120 . La luz utiliza la tecnologa de radiofrecuencia para la vinculacin, por lo cual no debe haber ms de 98 pies (unos 30 metros) entre luces adyacentes. The package include 2 lights.These 2 lights is factory linked, and can not linked any other lights. C D B A SOLUCIN DE PROBLEMAS Si la luz no se enciende, retire la tapa de la batera y revise si si la batera est conectada al conector de la batera. Si la conexin es correcta, cambie la batera por una nueva. CAMBIANDO LA BATERA Deslice el interruptor a su posicin de "OFF" (apagado). Use un destornillador Phillips (estrella) para retirar los 6 tornillos que sostienen la tapa de las bateras. Retire con cuidado el paquete de bateras de la lmpara y desconecte el conector de las bateras. Reemplace la batera antigua con una nueva batera recargable de litio (18650) de 3.7V, 2000 mAh. Conecte el conector de bateras e inserte el paquete de baterasen la lmpara. Vuelva a colocar la tapa de las bateras alinendola adecuadamente y vuelva a colocar los 6 tornillos que retir anteriormente. Deslice el interruptor a su posicin de "ON" (prendido). Para un rendimiento ptimo, permita que la lmpara se cargue a plena luz del sol durante 8-12 horas. Interruptor de encendido Tornillos Tapa de las batera Paquete de bateras 02/28/2020 S SOLAR INTELIGENTE LED DE ILUMINACIN DE ACTIVADO POR MOVIMIENTO ITEM: SR51FB22C-08 ADVERTENCIA DE LA FCC Advertencia: los cambios o modificaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento pueden anular la autorizacin del usuario para operar el equipo. Notas: Este equipo ha sido probado y cumple con los lmites para un dispositivo digital de Clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Estos limits estn diseados para la proteccin contra interferencias dainas en una instalacin residencial. Este equipo genera, utiliza y puede irradiar energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia perjudicial a la comunicaciones de radio. Sin embargo, no hay garanta de que no se produzcan interferencias en una instalacin en particular. Si este equipo causa interferencia perjudiciales a la recepcin de radio o televisin, lo cual puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o ms de las siguientes medidas:
Reorientar o reubicar la antena receptora. Aumente la separacin entre el equipo y el receptor. Conecte el equipo a una toma de corriente en un circuito distinto al que est conectado el receptor. Consulte con el distribuidor o un tcnico de radio / TV con experiencia para obtener ayuda. EXPOSICIN A RF: Este equipo cumple con los lmites de FCC de exposicin a la radiacin establecidos para ambientes no controlados. Este equipo debe ser instalado y operado con una distancia mnima de 20 cm entre el radiador y su cuerpo. El transmisor no debe colocarse ni operarse junto con ningn otro transmisor o antena. CUIDADO: No deseche las bateras de litio en la corriente de desechos municipales o por el fuego, ya que las bateras pueden explotar. No abra, provoque cortocircuitos ni mutile las bateras. Deseche las bateras de acuerdo con los reglamentos locales, estatales y federales. No mezcle las bateras viejas con las nuevas. No mezcle las bateras alcalinas, estndar (carbono-zinc) ni recargables (nquel-cadmio, nquel e hidruro metlico o ion litio). Para obtener ayuda e informacin adicional acerca de la instalacin, comunquese con servicio a clientes al 1-844-551-0680 de lunes a viernes de 8:00 A.M. a 5:00 P.M. en el horario del centro de EE. UU. customerservice@qx-usa.com
, WESTINGHOUSE, are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved. 02/28/2020 2/2S