SOLAR LED WALL LIGHT WITH MOTION SENSOR (FACTORY LINKED) ITEM: SR58FA01H-08 INSTRUCTIONS FCC WARNING Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING: Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries . For additional help and information regarding installation, contact customer service at 1-844-551-0680, 8am-5pm, CST Monday Friday customerservice@idctexas.com and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved. FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE ON POSITION TO FULLY CHARGE THE BATTERY. The intelligent solar LED motion activated light measures the available battery power capacity and adjusts the light's performance to maximize runtime. Tools Required INSTALLATION Hardware Included
(A) Screw X 4
(B) Wall Anchor X 4 Pencil Phillips-head Screwdriver Electric drill drill bit size:
7.5mm (3/10 in.) Parts 1 Marking the location Mark the location where you want to mount the light xture (Part C). Measure the width of two holes on the back of the light to align holes for the 2 screws (Part A) on the surface. The distance between the two holes is 5.12in. (130mm). Drill two holes.
(C) Light Fixture X 2 5.12in. (130mm) x x 2 Mounting the light fixture Insert the wall anchors (Part B) so they are ush with the surface. Insert the screws (Part A) and leave at least 1/4in. (6.3mm) of the screws (Part A) outside of the surface for holding the light. Mount the light (Part C) on the screws (Part A) by placing the keyholes on the back of the light over the screw heads. B A A C NOTE: Light xture will stay on for 30 seconds when triggered by motion delivering up to 2000 Lumens and revert back to standby mode delivering up to 50 lumens until motion is detected. For best performance, mount the light a minimun 6 feet (1.8 m) above the ground. Motion detection range is up to 20 feet (6 m), motion detection angle is up to 120. Light xtures use radio frequency technology to link, and light xtures should not be greater than 90 feet (27 m) apart for linked function to work properly. When one light is triggered by motion, both lights will activate and deliver up to 2000 lumens. The package includes 2 lights. These 2 lights are factory linked, and can not be linked with more of the same type light or any other lights. NOTE: If there are performance or quality issues, both units need to be replaced with another set. TROUBLE SHOOTING If light doesnt turn on, check the battery to ensure that it is making secure contact with the terminals. If this doesnt work, replace with a new battery. REPLACING THE BATTERY Slide the power switch to the "OFF" position. Use a Phillips head screwdriver to remove the 8 screws holding the battery cover in place. Replace old batteries with 2 new 3.7V, 2000 mAh lithium (18650) rechargeable batteries. Replace the battery cover by aligning it properly and replacing the 8 screws removed earlier. Slide the power switch to the ON position. For optimal performance, allow light fixture to charge in full sunlight for 8-12 hours, to fully charge the battery. Battery Cover Screws Batteries Power Switch E LMPARA DE PARED LED SOLAR CON SENSOR DE MOVIMIENTO (ENLACE DE FBRICA) ARTCULO: SR58FA01H-08 INSTRUCCIONES ADVERTENCIA DE LA FCC PARA EL PRIMER USO: LA LUZ SOLAR NECESITA CARGARSE BAJO LUZ SOLAR DIRECTA POR UN PERIODO DE ENTRE 8 Y 12 HORAS CON EL INTERRUPTOR EN LA POSICIN "ON" (PRENDIDO) PARA CARGAR COMPLETAMENTE LA BATERA. La luz LED solar inteligente activada por movimiento mide la capacidad de energa disponible de la batera y ajusta el rendimiento de la luz para maximizar el tiempo de ejecucin. Herramientas Necesarias INSTALACIN Herrajes Incluidos Advertencia: los cambios o modicaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento pueden anular la autorizacin del usuario para operar el equipo. Notas: Este equipo ha sido probado y cumple con los lmites para un dispositivo digital de Clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Estos limits estn diseados para la proteccin contra interferencias dainas en una instalacin residencial. Este equipo genera, utiliza y puede irradiar energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia perjudicial a la comunicaciones de radio. Sin embargo, no hay garanta de que no se produzcan interferencias en una instalacin en particular. Si este equipo causa interferencia perjudiciales a la recepcin de radio o televisin, lo cual puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o ms de las siguientes medidas:
(A) Tornillo X 4
(B) Anclajes de pared X 4 Partes Reorientar o reubicar la antena receptora. Aumente la separacin entre el equipo y el receptor. Conecte el equipo a una toma de corriente en un circuito distinto al que est conectado el receptor. Consulte con el distribuidor o un tcnico de radio / TV con experiencia para obtener ayuda. Lpiz Cabeza de Phillips Destornillador Taladro elctrico tamao de la broca de taladro: 7.5 mm (3/10 plg) 1 Cmo marcar el lugar de montaje Marque el lugar en el que quiere montar el artefacto de iluminacin
(Parte C). Mide el ancho de los dos oricios que estn en la parte posterior de la lmpara para alinearlos con 2 tornillos (Parte A) en la supercie. La distancia entre los oricios es de 5.12in. (130mm). Taladre dos oricios.
(C) Lmpara X 2 5.12in. (130mm) x x EXPOSICIN A RF: Este equipo cumple con los lmites de FCC de exposicin a la radiacin establecidos para ambientes no controlados. Este equipo debe ser instalado y operado con una distancia mnima de 20 cm entre el radiador y su cuerpo. El transmisor no debe colocarse ni operarse junto con ningn otro transmisor o antena. 2 Cmo montar la lmpara A B Inserta los anclajes de pared (Parte B) de manera que queden al ras de la supercie. Inserta los tornillos (Parte A) y deja al menos 1/4in. (6.3mm) de los tornillos (Parte A) afuera de la supercie para sostener la lmpara. Monta la lmpara (Parte C) en los tornillos (Parte A) al colocarlos oricios de la parte posterior de la lmpara en las cabezas de los tornillos. NOTA: Cuando el movimiento produzca hasta 2000 lumens, la lmpara permanecer durante 30 segundos y volver al modo de espera, produciendo hasta 50 lumens hasta que se detecte el movimiento. Para un rendimiento ptimo, coloque la lmpara al menos a 6 pies (1,8 metros) del suelo. El rango de deteccin de movimiento es de hasta 20 pies (6 metros) y el ngulo de deteccin de movimiento es de hasta 120. Las luminarias se conectarn mediante tecnologa de radiofrecuencia y la distancia entre ellas no exceder de 90 pies (27 metros) para que la conexin funcione correctamente. Cuando una luz es activada por el movimiento, ambas luces se encienden y producen hasta 2000 lumens de luz. El traje incluye 2 luces. Estas dos luces estn vinculadas a la fbrica y no pueden estar vinculadas a ms del mismo tipo de luz o cualquier otra luz. Nota: si hay problemas de rendimiento o calidad, ambas unidades necesitan ser reemplazadas por otra. C A SOLUCIN DE PROBLEMAS Si no se enciende la luz, revise la batera para asegurarse que estn haciendo contacto rmemente con las terminales. Si esto no funciona, reemplace la batera con una nueva. CAMBIANDO LA BATERA Deslice el interruptor a su posicin de "OFF" (apagado). Use un destornillador Phillips (estrella) para retirar los 8 tornillos que sostienen la tapa de las bateras. Reemplace la bateras antigua con dos nueva bateras recargable de litio (18650) de 3.7V, 2000 mAh. Vuelva a colocar la tapa de las bateras alinendola adecuadamente y vuelva a colocar los 8 tornillos que retir anteriormente. Deslice el interruptor a su posicin de "ON" (prendido). Para un rendimiento ptimo, permita que la lmpara se cargue a plena luz del sol durante 8-12 horas, para cargar completamente la batera. Tapa de las batera Tornillos Bateras Interruptor de encendido S CUIDADO: No deseche las bateras de litio en la corriente de desechos municipales o por el fuego, ya que las bateras pueden explotar. No abra, provoque corto circuitos ni mutile las bateras. Deseche las bateras de acuerdo con los reglamentos locales, estatales y federales. No mezcle las bateras viejas con las nuevas. No mezcle las bateras alcalinas, estndar (carbono-zinc) ni recargables (nquel-cadmio, nquel e hidruro metlico o ion litio). Para obtener ayuda e informacin adicional acerca de la instalacin, comunquese con servicio a clientes al 1-844-551-0680 de lunes a viernes de 8:00 A.M. a 5:00 P.M. en el horario del centro de EE. UU. customerservice@idctexas.com and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved.