FCC ID: 2ADQY-525794 High-Power Wireless 150N Outdoor CPE / Access Point

FCC INFORMATION (additional) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may not be co-located with any other transmitter or antenna.

Quick installation guide V1.0 May 2015 Intracom Asia Co., Ltd. This guide describes how to quickly install CPE and how to easily configure outdoor CPE step by step followed the guidance which offers a very visual way to help end user/

maintenance staff of network etc spent a little bit time to have a whole ideas how to make CPE work fine. 1 QuickConfigurationguideline



TheFirstStep Connectingthedevice

Interface Power Reset LAN WAN Pic- 1 CPE Physical Interface Power: DC Jack, please equip with 12V/1A DC power adapter Reset: Two ways of restoring factory defaults as below 1) Go to SystemFactory Defaults web page, press Load Defaults button;

2) Press reset button in 5-10s, then release it, device will restore configuration to factory defaults. Pls keep regular power supply of the device in process of implementing RestoreFactoryDefaults,otherwisemaycausedevicedamage. Caution Intracom Asia Co., Ltd. 1 Connection means as figure-2:

CPE PowerAdapter 120VAC POEMixer POE LAN PC LAN Figure-2 CPE connect to POE Mixer & Power adapter diagram Incorrect connection means or plug in power supply which dont belong to the package may cause device damage!

Caution The Second Step: Start-up and Login 1As figure-2 shown, please make it ready for CPE connect with PC 2Consign local IP address with 192.168.2.X X=2-254on PC side(The IP address must keep same segment with CPEs gateway address),subnet mask:255.255.255.0 As figure-34 shown Intracom Asia Co., Ltd. 2 Figure-3 Configure IP address of PC Figure 4 LAN IP address settings on PC side 3Connecting to equipment via wireless After basic settings of the equipment, if you want to access internet or just the equipment via wireless, please configure local Wireless Network properties, lock mouse on the icon of Wireless Network then click right button of mouse, youll see figure- 5 shown, then click View Available Wireless Network to filter out which AP or Intracom Asia Co., Ltd. 3 router you wish to connect with. Defaults SSID:CPE-XXXX; Defaults Password:blank Figure- 5 Wireless Network Icon Figure- 6 Wireless Connection Settings Intracom Asia Co., Ltd. 4 A. IfyourLaptoporPChasinternalwireless802.11b/g/nLANcard,butcouldntfindwirelessnetwork, Caution pleasecontactwithservicedepartmentofyourcomputervendorforhelp 1) ClickrightbuttonuponMyNetworkPlaces,thenselectProperties,ifyoucouldfindLocal NetworkbutthereisnoWirelessNetworkicon. 2) ThereisLocalNetworkicon,butclickrightbuttonuponthebuttonandselectProperties,justfind RegularandAdvancedoption,butthereisnoWirelessNetworkSettingsevenifyouhaveever successfullyconnectedwithotherwirelesshotspot. B. ClickonRefreshNetworkList,allhotspotlistscannedwillbelistedontheright.SelectspecifiedSSID youwishtoconnectwith(Ifpasswordisamust,pleaseinputitinpopuppage) 4Enters http://192.168.2.1 on IE, then youll see login page as Figure-8 shown;

Defaults User Name: admin; Defaults Password: admin Figure-7 Enter gateway address in IE explore Figure-8 Login Page The Third Step Setup Wizard While you login web page, please go to Setup WizardclickScanSelectSSID Intracom Asia Co., Ltd. 5 Enter encryption passwordSelect specified WAN type PPPOEDHCPStatic click Next Step Figure 9 WISP Settings Note DHCP: IfthedeviceconnecttoDHCPServerofuplinkorWISP,plsselectthismode.The devicewillobtainIPaddressfromuplinkDHCPserverorWISPautomatically. PPPoE: IfWISPofferPPPOEaccesstype,plsselectthismode.Youshouldfillinboththe UserNameandPasswordthatyourISPsupplies StaticIfWISPofferStaticIPaccess,plsselectthismodeandenterIPaddress/Subnet Mask/GatewayandDNSserverIPaddress LAN Settings:

You could change Gateway IP adress here or keep defaults,then click Next DHCP Server Settings:

You can enable or disable DHCP server here,then click Next Figure - 10 LAN Settings Intracom Asia Co., Ltd. 6 Figure - 11 DHCP Server Settings Wireless Settings To configure wireless settings of the device,you could enable or disable wireless here,select security mode/set encrypt key etc,after that click Apply to save previous settings. Figure - 12 Wireless Settings Thedevicewillrebootafterchangingthesesettings,ifyoujustkeepdefaultsvaluepls clickNextforfurtherprocess Note:

Intracom Asia Co., Ltd. 7 The Fourth Step AP Client Settings AP ClientIn this modethe device associate with nearby AP and checks the network device combination as a standard mobile unit(MU).The access point then forms a wireless bridge between the wired LAN and clients through the device. CPE broadcasting its SSID, client devices obtain IP address from uplink hotspot or WISP. BothEthernetportareLANportonAPClientAPWISPmode.(BothLANportsupport Note:

POEforAP1105modle) Application Topology:

LAN CPE APor WLAN Figure - 13 Network Topology under AP Client mode AP Client setup guide Connects to wireless AP or WLAN base station Check Operation Modeselect AP Clientclick Scanselect specified SSID you wish to connect with, then fill-in password Click Apply to save settings Intracom Asia Co., Ltd. 8 Figure - 14 AP Client settings Channelwithoutsetting,sinceChanneloftheCPEwillautomaticallyconsistentwith Note:

thefrontendWLANbasestationinAPandAPClientmode. CPEwilldisableitsDHCPserverinAPClientmode,formanagementpurposeyoucan assigndifferentIPaddressforeachCPE If there is no targeted SSID in checking list, youd better have some more Scan process. But if still nothing in checking list please double check if the frequency of WLANsworkingchannelbeyondyourCPEsscope.e.gCPEsupport11channel. Note:

MoreoverplscheckifthecommunicationprotocolmatchbetweenCPEandbase station. Sometimeplsrestorefactorysettingsbeforeyouconfigurethedevice WDS Configuration Intracom Asia Co., Ltd. 9 Figure -16 WDS Settings WDSBridge/RepeatersetupjustsamewithAPClientmodegenerally.butfrontend APsupportWDSisamustwhenCPEisinWDSmode. Note:

The fourth step AP settings Go to check Operation ModeAccess PointAP,youll see figure -17 page. In this page you may set wireless access point related options by your needing,after that please click Apply to save settings and reboot device. Intracom Asia Co., Ltd. 10 Figure - 17 AP Settings Select specified one you wish to enable its SSID, clickEnable. Once you enable BSSID, you could select one Channel and configure specified wireless parameter based the BSSID, also you could enable multiple SSID option. Once enable SSID CPE will broadcast its name. Select SSID blank you can change its name here. Broadcast SSID, Enable the option, SSID will be visible you can san the BSSID name by PC or laptops wireless scan tools, once you disable it user couldnt find the SSID by scanning tools, the SSID has been hided. But if you still wish to connect with the SSID, just enter the SSID name upon related interface item manually. Security Mode, In this option you can configure encrypt mode, key etc, security mode currently support OpenWEPWPCPESKWPA2PSKWPCPESK/WPA2PSK etc. Security Type, Suggest security type to be TKIP mode which is more strengthen encryption type. Intracom Asia Co., Ltd. 11 The Fifth step: Router(Gateway) Configuration ClickOperation ModeRouter(Gateway) go to basic configuration page,as figure

-12 shown:

Note:

Router(Gateway)iswhatweusuallysaySOHOrouterfunction,Routerconnecttowired ISPtoaccessinternet(usuallybeADSL,Cableetc).Herenodetaileddescription,if necessary,pleaserefertotypicalSoHowirelessrouterconfiguration. Figure - 12 DHCP:WhentheDeviceconnectstoaDHCPserver,orISPsupportDHCPservice,pleasechoose thistype.TheDevicewillgettheIPaddressautomaticallyfromtheDHCPserverortheWISP. Oncetheconnectionbuildupsuccessfully,youcanaccessinternet. PPPoE:IfyourwirelessISPssupportPPPoE,youshouldchoosethistype.Inthiscondition,you shouldfillinboththeUserNameandPasswordthatyourISPprovides. StaticInthistype,youshouldmanuallyfillintheIPaddress,SubnetMask,DefaultGateway,and DNSIPaddress,whicharespecifiedbyyourISP. The Sixth Step:

Connection status After you finished related configuration and you wish to check if settings is succeed or not, please go to Status page for more details, as figure -19 shown Intracom Asia Co., Ltd. 12 Figure - 19 CPE Connection Status When CPE successfully connect with front-end WLAN base station or AP, the status will be Connected, also other options listed on the page .e.g Peer-end SSID,MAC address RSSI etc Note:

its weak than this CPEs Signal strength should be greater than 75dBm,if Bridge/Repeaterjointwillbeworse.Itsperformanceofrepeaterjointwillgetworse inNLOScondition,butinorderto havethebestsignalstrengthandthroughputyou canadjustthedirectionofCPE'sdirectionalANT 2 PC Configuration:

To set automatic obtain IP address on PC or laptop side, then PC will get a IP address from CPE or ISP WLAN DHCP Server. As shown in Figure 20. Intracom Asia Co., Ltd. 13 Figure - 20 IP address settings on PC Once you finished this setting, you can implement Ping command to test if the connection is done. 3 System Click System to go to system management page, as shown in Figure 21. Figure - 21 System Management Password Settings: To set system administrator and password here. Time Settings: To set time zone and time information here. Backup&Restore: To export system configuration file to local document or import backup-file for restoring configuration to factory defaults. Intracom Asia Co., Ltd. 14 Factory Defaults: Restore system configuration to factory defaults. Reboot: re-power on system by software interface. WEB Server: To set web server related option here. Firmware Upgrade: To upgrade CPEs firmware for obtaining a more stable and functional performance of the CPE. TorestoreCPEtofactorydefaultsviaphysicalresetbuttononhousingbypressing resetbuttonin510sorclickResetbuttononwebpage. Note:

You could check system logs on Log Management page, as shown in Figure -22 Figure - 22 System Logs Intracom Asia Co., Ltd. 15 4 Troubleshooting:

Troubles SYS indicator doesnt shine Couldnt login Web page CPE could not connect with front-end AP Status:

disconnected Couldnt detect targeted CPE signal of Treatment Please double check if the connection is done between POE box and LAN port. Right way is that put POE interface connect with CPE and LAN with PC or laptop. 1. Please check if both IP address is in same range. You can check it via selecting Start-Run bland and implementing CMD command, by ping 192.168.2.1 to test if the connection is done;

2. Restore factory defaults, then login again;

3. Double check there is no same IP address of 4. 5. 6. 1. 4. UTP 192.168.2.1 in same network range;

Please check if driver of your PC WLAN Nic has been installed correctly, and Ethernet cable is good.(10/100M is recommended strongly);

By entering arp -dcommand over Start-Run interface to clear arp bing;

To clear the Tem&Buffer filer of IE browser To scan wireless network again and reconnect hotspots;

Ethernet cable 2. Double check if wireless option of the CPE has been set correctly;

3. Double check if encrypt type & Key could match between AP and CPE;

If wireless signal of front-end AP is very poor, recommend it greater than -75dBm. Try to perform Scan command twice times, but if targeted SSID still be invisible, please check if channel of CPE could support front-end AP or hotspots. Such as AP or hotspots working in Channel 11. PC couldnt access internet, but indicator show connection has been connected successfully. 2. 3. To restore factory defaults 1. Please check IP addressDNS etc is right on PC side For DHCP, set WLAN NiC to obtain IP address automatically;

For Static IP address, please ask for correct IP &

DNS address from your ISP. In powered on status of the CPE, press RESET button in 5-10s,then release the button, system will restore Factory Defaults. Figure - 1 Troubles and treatment Intracom Asia Co., Ltd. 16

*. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Intracom Asia Co., Ltd. 17