FCC ID: 2AFDI-ITCNFA324 InFlyt Wireless Mode Controller

ITCNFA324 Module Certification OEM Integrator Instructions Document Number: ITCNFA324-IG-001 Revision Number: C NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFORMATION INTRINSYC Technologies Corp. claims proprietary rights to the material disclosed hereon. This drawing and/or technical information is issued in confidence for engineering information only and may not be reproduced or used to manufacture anything shown or referred to hereon without direct written permission from INTRINSYC Technologies Corp. to the user. This drawing and/or technical information is the property of INTRINSYC Technologies Corp. and is loaned for mutual assistance, to be returned when its purpose has been served.

Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 ITCNFA324 Module Certification ITCNFA324-IG-001 C 30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. IDENTIFICATION Document Title Document Number Version Date HISTORY Version Date Purpose A B C 27-Jul-15 Original Document 26-Oct-16 Added additional dipole antenna to Allowable Antennas. Removed reference to the FCC Interference Handbook booklet in section 11.1 as FCC does not produce the handbook anymore. 30-Nov-18 Added additional chip and Kontron WiFi Flag antennas to Allowable Antennas. Pages All 1, 2, 6 1,2 Note: The ITCNFA324 radio module (the Module) is designed for use only in specific countries in which Intrinsyc has obtained certificates of compliance with local laws and regulations. Therefore, the Module may not be sold, operated or incorporated into products for use in countries for which it has not been certified. In addition, any deviation from the settings, methods, conditions and restrictions for integration of the Module into a host system, as defined in this document, could be a violation of applicable national law and may be punishable as such, and in such event, the products into which the Module is incorporated may not be lawfully distributed or sold in such countries. Intrinsyc assumes no responsibility for any such liability or loss related to installation or operation of the Module. Intrinsyc Confidential Information i Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. Table of Contents 1 Introduction ........................................................................................................................... 1 2 Applicable Module ................................................................................................................ 1 3 Additional Regulatory Conformance Testing and/or Submissions Required by the Integrator ....................................................................................................................................... 1 4 Compliant/Allowable Tx Power Settings ............................................................................ 1 5 Allowable Antennas to use with the Radio Module ........................................................... 1 6 Antenna Placement inside the Host System and RF Safety .............................................. 2 7 Simultaneous Transmission with other Integrated or Plug-in Radios ............................. 3 8 Module May Not Be Installed by End Users ...................................................................... 3 9 Required Labeling on the Outside of the Host ................................................................... 3 9.1 FCC .................................................................................................................................. 3 9.2 European Community R&TTE ........................................................................................ 4 10 Required Labeling on the Module ....................................................................................... 5 FCC Labelling on the Module ...................................................................................... 5 Rest of World labeling on the Module ......................................................................... 5 11 Required Regulatory Wording for User Manual/Installation Manual ............................ 6 FCC compliance information ....................................................................................... 6 Industry Canada notice ................................................................................................. 7 European Community (R&TTE) user manual wording and declaration ...................... 8 European Community (R&TTE) Declaration of Conformity for System .................... 8 12 OEM Integrator Checklist ................................................................................................... 8 11.1 11.2 11.3 11.4 10.1 10.2 Intrinsyc Confidential Information ii Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. 1 Introduction This document describes the steps that the OEM integrator must follow when designing and manufacturing a system utilizing the ITCNFA324 Module. Failing to follow the instructions in this document may invalidate the FCC certification and authorization of the Module for use in the U.S. and other countries. The Module certifications described in this document apply only to radio conformance for the Module. The OEM integrator is responsible for all system-level EMI/EMC and Product Safety testing and certifications that apply to the host system in the U.S. and other countries where the system will be marketed or sold. 2 Applicable Module Part Number: NFA324 (Regulatory model: ITCNFA324) FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 3 Additional Regulatory Conformance Testing and/or Submissions Required by the Integrator The modular certifications apply to the radio conformance for the Module only. The OEM integrator is responsible for additional system-level EMI/EMC and Product Safety testing and certification that applies in the U.S. and other countries to the host system containing the Module. This includes but is not limited to Federal Communications Commission (FCC) Part 15 Class B Digital Emissions. These system-level EMC tests are to be done with the Module installed and included in the scope of the submission. Some of the countries for which modular certifications are provided require additional submissions, authorizations or import permission by the system-vendor or importer. The integrator is responsible for these additional actions. Modular radio certification is not possible in some countries. For such countries, OEM integrators must ensure radio certification for the end system is obtained, before placing the product on the market. 4 Compliant/Allowable Tx Power Settings Any adjustments made to increase transmit power settings will invalidate all radio certifications for this module. 5 Allowable Antennas to use with the Radio Module The module is certified for use with certain antennas as described in this section. Allowed Antenna Types:

1. PIFA with omnidirectional pattern formed from stamped metal or film. 2. Dipole antenna 3. Chip antenna 4. Kontron WiFi Flag Antenna P/N: 730001001 Intrinsyc Confidential Information 1 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. Table 1 Allowed Maximum Gain (dBi) PIFA, Including Antenna Cable Loss Table 2 Allowed Maximum Gain (dBi) Dipole, Including Antenna Cable Loss Table 3 Allowed Maximum Gain (dBi) Chip, Including Antenna Cable Loss 2.4 GHz 5.150-5.350 GHz 5.470-5.850 GHz 2.4 GHz 5.150-5.350 GHz 5.470-5.825 GHz 2.4-2.5 GHz 4.9-6.0 GHz 2.4 -2.5GHz 4.9-5.825 GHz 3.62 3.08 4.76 3.8 5.5 5.5 2.68 5.0 2.6 4.0 Table 4 Allowed Maximum Gain (dBi) Kontron WiFi Flag Antenna P/N: 730001001, Including Antenna Cable Loss Use of other antenna types or the same type of antenna but with higher gain than listed above is not allowed without additional testing and appropriate FCC approval. Use of a similar antenna may only require a C1PC to confirm the performance for SAR is the same or better (i.e. lower) but only an equivalent antenna can be used without any additional testing. 6 Antenna Placement inside the Host System and RF Safety The FCC and other countries regulatory bodies impose strict conditions and limitations on the RF exposure levels of end products. Acceptable RF exposure levels for this Module depend on transmit power, the location of the transmitting antenna(s) inside the host system and the expected separation of the transmitting antennae to the end user. OEM integrators must take great care to ensure each host system complies with the applicable RF exposure requirements. The antenna-to-user (bystander) separation distance must be greater than 20 cm. Failure to adhere to these separation/spacing rules will invalidate the FCC certification for the Module. This separation is measured between the closest point of each transmitting antenna inside the host device to the point of contact by the user or nearby person outside the host device. For notebooks/netbooks/laptops with antennae in display section, the LCD is opened 90 degrees/perpendicular to the keyboard. The separation distance is then measured from the nearest point of each transmitting antennae to the bottom of the host. Use in the keyboard section of a netbook or laptop or use in a tablet device or convertible tablet would require host-specific testing. For notebooks/netbooks/laptops, the transmitting antenna cables shall be positioned away from the antenna elements to conform to the configuration tested for compliance. Intrinsyc Confidential Information 2 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. When transmitting antennae are installed in the display section of notebook/netbook/laptops, the display section shall not have metallic components and material that can influence or change the operating and RF exposure characteristics of the antennae. The separation between the main and aux antennae must be at least 3 cm. The transmitter module may not be co-located with any other transmitter or antenna. SAR evaluation is required if the separation distance between the user or bystanders and the device is less than or equal to 20 cm. Where one or more of the conditions above cannot be met for a particular host system, additional testing is required to secure the necessary certifications for the system. Note: These restrictions do not apply to receive-only antenna. 7 Simultaneous Transmission with other Integrated or Plug-in Radios The FCC imposes conditions and limitations when additional radio(s) are co-located in the same host system as the Module with capability to transmit simultaneously. Co-locating other radios such as an integrated or plug in Wireless WAN/cellular radio with the Module requires additional evaluation and possibly submission for authorization from the FCC. Because the rules are highly dependent on the characteristics of the particular radios that are co-located and simultaneously transmitting, the OEM integrator should seek guidance from a knowledgeable test lab or consultant to determine if additional testing and FCC certification is required. In this case, failure to evaluate and follow the required FCC procedures will invalidate the FCC certification of the Module and end system. 8 Module May Not Be Installed by End Users FCC rules require this Module to be installed in host systems at the factory by the OEM integrator. Thus, end users of the system my not install the Module. Therefore, the host product user instructions must not advise the end user on how to access or remove the Module. Additional FCC authorization/filing is needed to allow end user installation of the radio modules. If modules are provided to the end users for installation in the host, a two-way authentication protocol is required to limit the module to operate only with the authorized host system. 9 Required Labeling on the Outside of the Host FCC 9.1 The FCC requires a label on the outside of the host system visible to the end user. Example wording is:

Contains:

FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 The FCC requires a logo signifying emission compliance on the outside of the host system. The OEM integrator is responsible to perform FCC Part 15 Class B digital emissions testing on the end system with the radio Module Intrinsyc Confidential Information 3 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. installed. The FCC logo below should not be affixed unless the OEM integrator has obtained the necessary Part 15 approval, e.g., self-declaration of conformity. If the host system is approved to FCC Class B digital emissions limits under a grant of certification issued by a TCB, the FCC ID number shown on the grant should be used on the label instead of the FCC logo below. Also see https://www.fcc.gov/logos. European Community R&TTE 9.2 The European Community R&TTE Directive requires the CE Marking shown below on the outside of the host AND on the outside of the shipping container/packaging. For 2.4 GHz For 5 GHz or 2.4 GHz = 5 GHz dual bands The European Community R&TTE Directive also requires the following note to consumers on the outside of the shipping container/packaging:

Important Notice: This product is a Radio LAN device operating in the 2.4 & 5 GHz bands (or 2.4GHz band) for Home and Office use in the E.E.A. AT CZ FI EE IS LV PL SK BE DE FR HU LI MT PT CY ES GR IE LU NO SI CH DK GB IT LT NL SE 4 Intrinsyc Confidential Information Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. Note: The Integrator is expected to translate text into appropriate languages for the European countries into which the product will be marketed or sold. 10 Required Labeling on the Module FCC Labelling on the Module 10.1 The OEM integrator must ensure that the FCC ID is affixed on the Module or in a User/Installation Manual along with other country certification numbers and logos as described herein. Note: the original Module manufacturer may affix regulatory labeling at time of Module manufacturing. However, the OEM integrator must ensure that Module labeling is complete, correct, and applicable for all the countries to which the host system is to be imported, marketed, or sold. 10.2 Rest of World labeling on the Module The OEM integrator must ensure the Module includes a global regulatory label with certification numbers and logos for all the target countries. The OEM integrator is responsible to confirm the final regulatory label on the radio Module contains all the required certification IDs for all the countries in which the host system will be marketed or sold. Intrinsyc Confidential Information 5 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. 11 Required Regulatory Wording for User Manual/Installation Manual The OEM integrator must include text in the user manual meeting the regulators requirements. The text below or similar wording should be used. (Text in red font must be replaced.) FCC compliance information 11.1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following to conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate warranty and all applicable regulatory certification and approvals, including authority to operate this device. FCC Part 15 Digital Emissions Compliance We [System Manufacturer Name, Address, Telephone], declare under our sole responsibility that the product

[System Name] complies with Part 15 Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the use is encouraged to try to correct the interference by one of more of the following measures:

Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from the one the receiver is connected to. Consult the dealer or an experienced radio.TV technician for help.

(Notice for 5GHz and/or when co-located with 5GHz transmitters, the following statements should be provided for user information.) Operations in the 5.15-5.25GHz band are restricted to indoor usage only. (For 5GHz only)

(RF exposure statement) Radiation Exposure Statement The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Intrinsyc Confidential Information 6 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. Industry Canada notice 11.2 This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable.

(Notice for 5GHz and/or when co-located with 5GHz transmitters, the following statements should be provided for user information.) Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the bands 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices Avertissement:

Le guide d'utilisation des dispositifs pour rseau-x locaux doit Inclure des instructions pccises su:r les restrictions susmentionnes, notamment:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5150-5250 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e.;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 57255825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour l'exploitation point point et non point point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d ., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-

5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Intrinsyc Confidential Information 7 Title Date Originated Revision:

15-Nov-

182015 C Doc #: ITCNFA324-IG-001 Date Revised:

30-Nov-2018 INTRINSYC TECHNOLOGIES CORP. 11.3 European Community (R&TTE) user manual wording and declaration Europe EU Declaration of Conformity Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:

EN300 328, EN301 893, EN 301 489-17, EN60950, EN 62311 11.4 European Community (R&TTE) Declaration of Conformity for System In addition to including the radio conformity wording described in the previous section in the user manual, the end integrator must also create and sign a European Declaration of Conformity (DoC) for all European Directives applicable to the end product. At a minimum, this will be a DoC per the R&TTE Directive covering Radio, EMC, Product Safety and RF Exposure essential requirements. The DoC must reference harmonized standards used for all radios present in the system. 12 OEM Integrator Checklist The OEM Integrator will integrate the Module in the host systems in accordance with the instruction specified in this document and the documents referenced herein. The OEM Integrator will ensure the Module is integrated in a host system using only the approved antenna models(s) described in this document. The OEM Integrator will ensure the antennal placement inside the host system will maintain the required spacing to the end user for RF Exposure compliance, as specified in this document. If other radios are integrated inside the host with the Module, the OEM Integrator will contact a test lab or TCB to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. The OEM Integrator will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. The OEM Integrator will ensure the Modules transmit power does not exceed the levels specified in this document. Intrinsyc Confidential Information 8

User Guide eSight documentation is updated periodically for accuracy and completeness. Check esighteyewear.com/support for the latest version No part of this publication may be reproduced without the express written permission of eSight Corporation. eSight Eyewear and eSight and associated images and symbols are trademarks of eSight Corporation. eSight is a registered trademark in Canada and the U.S. and may be pending or registered in other countries. Various U.S. and other patents pending. All other trademarks, registered trademarks, product names, and company names and/or logos cited herein, if any, are the property of their respective holders. eSight reserves the right to improve the contents of this document without notice. eSight Corporation 515 Legget Drive, Suite 200 Ottawa, ON, K2K 3G4 Canada 4000809 Rev. 2 Copyright 2020 eSight Corporation All Rights Reserved. Publication Release February 2020 About Regulatory Symbols Medical Device ManufacturerIndicates the name and address of the medical device manufacturer. Authorized European Representative Indicates the name and address of the legal entity designated by eSight Corporation to represent them in the European Union. CE Mark This mark indicates that eSight complies with applicable European Union regulations. Medical Device Indicates eSight is a medical device. Caution Consult the instructions for use for important information, such as warnings and cautions. Consult the Instructions for Use Indicates users must read the Instructions for Use prior to using eSight. eIFU Indicator Indicates that Instructions for Use are available in electronic format on the eSight Corporation website at the stated URL. FCC Mark This mark certifies that the electromagnetic interference from eSight is under the limits approved by the Federal Communications Commission. Recyclable The product packaging is recyclable. Catalogue Number Indicates the product part number for eSight. Serial Number Indicates the serial number of your eSight. Date of Manufacture Indicates the date when eSight was manufactured. Country of Manufacture Indicates the country of manufacture/country of origin as Canada. Warning Identifies hazards that can kill or severely injure in the event of exposure. Caution Identifies hazards that can cause slight to moderate harm in the event of exposure. Loss of Data Advises that failure to take or avoid a specific action could result in loss of data. Note Supplies information that may apply only in special cases. Tip Provides useful suggestions on how to apply techniques and procedures. Table of Contents Package Contents ..................................................Page 1 About eSight 4 ........................................................Page 2 Safety .......................................................................Page 6 Power.......................................................................Page 12 Wear ........................................................................Page 15 Use ...........................................................................Page 22 Gestures ..................................................................Page 25 Control Via eSight 4 ...............................................Page 26 Control Via the Remote .........................................Page 29 Swap ........................................................................Page 32 Charge .....................................................................Page 34 Clean ........................................................................Page 36 Regulatory Notices ................................................Page 38 Specifications ..........................................................Page 45 Contact Us ...............................................................Page 47 Package Contents eSight 4 Remote &

2 AAA Batteries USB Cable &

Power Adapter Guides Carrying Case Rechargeable Batteries 1 About eSight 4 Intended Use eSight 4 is intended for use as a vision aid to help people with low vision see better while performing various activities of daily living (excluding driving, operating machinery, or other visually demanding activities for which there is an inherent risk of injury or death). Front View Camera Visor Halo Size Dial Halo Light Ambient Light Sensor Focus Sensor Light Recording Light 2 About eSight 4 Left Side View Left Arm Right Side View Tactile Dots Right Arm 3 Left Arm Dial Right Arm Dial Touch Pad About eSight 4 Top View Left Arm Left Arm Dial Right Arm Right Arm Dial Context Button Power Button Status Indicator 4 About eSight 4 Back View HDMI Port Left Arm Right Arm USB-C Port Screen Rechargeable Battery 5 Safety Be safe! Read this safety information before you use eSight. The term eSight refers to the eyewear and its batteries, USB power adapters, cables, and eSight-approved accessories. This safety information is updated periodically for accuracy and completeness. Check esighteyewear.com/support for the latest version. Failure to comply with warnings can cause serious injury or death. eSight eSight Corporation makes no claims about the suitability of eSight for any specific activity. While wearing eSight, do not drive, operate machinery, or engage in other visually or physically demanding activities that may cause injury or death. While using eSight in mobile situations, such as walking, partially raise the visor for greater peripheral vision and situational awareness. Avoid low objects. eSight can obscure your field of vision above the line of sight. Only use eSight and its software with authorized devices, accessories, and software. Use of any unauthorized device, accessory, and/or software or hacking eSight and its software may result in injury to you or others, may cause performance issues, or damage to your system and related services. 6 Safety Battery Hazards Failure to follow battery warnings may cause batteries to leak, become hot, explode, or ignite resulting in serious injury and/or damage. eSight uses Lithium batteries. Do not expose any batteries to hot, humid, wet, or corrosive environments. Do not expose eSight to moisture; high humidity; high concentrations of dust or airborne materials; heat sources; high temperature locations, like a car, hair dryer, or microwave oven; or strong, direct sunlight. Do not expose eSight to temperatures over 60C (140F). Do not place or store eSight in a pressurized container. Do not heat, open, puncture, mutilate, or service any batteries. In the event of a battery leak, do not allow the liquid to contact the skin or eyes. If contact occurs, wash the affected area with large amounts of water and seek medical advice immediately. Your remote contains AAA batteries. CHOKING HAZARD: The remote is not a toy. It contains batteries, which are small parts. Keep away from children and pets. 7 Safety Do not ingest battery. Chemical burn hazard. If a battery is swallowed, it can cause severe internal burns and potential perforation of the esophagus in just 2 hours and can lead to death. If you think batteries might have been swallowed or placed inside any part of the body, seek medical attention immediately. If the battery compartment does not close securely, stop using the remote, and keep it away from children. The remote contains user-replaceable batteries. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. The integrated battery on the eSight halo must be replaced by eSight Corporation or an authorized service provider. Properly dispose of batteries promptly according to instructions. Do not dispose of batteries in a fire or landfill. Electrical Shock Hazard Use only eSight-approved USB power adapters, batteries, cables, and accessories. Where the prongs on the USB power adapter may be folded for storage, make sure the prongs are fully extended before plugging the USB power adapter into a power outlet. Where the USB power adapter comes with additional plug adapters, make sure the plug adapter is of the proper configuration for the outlet and is fully seated onto the USB power adapter. 8 Safety Do not use eSight and/or electrical sockets if any part is broken, damaged, or loose. Stop use immediately. Do not attempt to take apart, open, service, or modify eSight. Do not drop eSight or expose eSight to liquids. Do not plug in or operate eSight with wet hands. Pull the plug to disconnect the USB power adapter. Do not jerk, bend, knot, or damage the cables. If you notice strange smells or sounds or see smoke or liquids coming Failure to do so may result in injury, fire, or explosion. from eSight, stop using it immediately and contact eSight Support. Interference with Medical Devices eSight emits radio waves. These can affect the operation of nearby electronics, including cardiac pacemakers, hearing aids, and defibrillators. If you have a pacemaker or other implanted medical device, do not use eSight without first consulting your doctor or the manufacturer of your medical device. Maintain a safe distance of at least 15 centimeters (6 inches) between eSight and your medical device, and stop using eSight immediately if you observe interference with your medical device. Use in Hospitals, Aircraft, and Other Environments In some situations or environments, such as hospitals, aircraft, explosive environments, or other environments near equipment that can be interfered with by radio frequency, the use of wireless devices is restricted. When in doubt, ask for authorization prior to turning on eSight. 9 Safety Explosive Environments Turn off eSight in potentially explosive environments. Always comply with regulations, instructions, and signs in potentially explosive environments. Do not use eSight at gas stations, near fuels or chemicals, or in blasting areas. Servicing Do not attempt repairs. Opening or removing covers may expose you to dangerous energy points or other risks. Refer all servicing to eSight Corporation or an eSight Authorized Service Provider. Failure to comply with cautions can cause injury or property damage. Heat Turn off eSight before storing it in its case. eSight may become very warm during normal use. Allow for adequate air circulation under and around eSight. If eSight gets uncomfortably warm, remove it and take a break. Do not touch hot surfaces for prolonged periods. eSight complies with the user-accessible surface temperature limits defined by the International Standard for Safety of Audio/Video, Information and Communication Technology Equipment (IEC 62368-1). 10 Safety Skin Irritation Light Sound Trip Hazard Cleaning eSight is worn next to your skin. Adjust the halo only until snug. Stop using eSight if you notice skin irritation. If symptoms persist, consult your physician. Do not use the light close to the eyes of people or pets. Excessive exposure to loud sounds can cause hearing damage. Use only the minimum volume necessary to hear clearly in quiet surroundings. Do not increase the volume to block outside noise. Exposure to loud sounds may distract your attention from your surroundings and cause an accident. Arrange cables so that people and pets are not likely to trip over or accidentally pull on them while they walk through the area. Do not apply foreign substances, such as household cleaning products, to eSight. Refer to the cleaning instructions in this guide. 11 Power Turn on eSight & Wake Remote Step 1 eSight On Step 2 Wake Remote Any Button eSight - Sleep/Resume & Off Sleep/Resume Off 12 Power Auto Sleep & Auto Off 13 Power For mobile activities, power eSight with the rechargeable battery. 2-3H For stationary activities, power eSight from the USB-C port at the back of the right arm using the USB power cable and adapter. Powering eSight from the USB-C port does not charge the rechargeable battery. 14 Wear Adjust the size of the halo. While wearing eSight, turn the Halo Size Dial counterclockwise to tighten and clockwise to loosen the halo. While handling eSight, you may notice that eSight flexes. This is normal and by design for your comfort. 15 Wear eSight feels secure on your head with an angled halo. 16 Wear Center eSight on your face Using the nose pads as a reference, center eSight on your face. If eSight is not properly centered on your face, the camera will not point where you are looking. The nose pads can rest weightlessly on your nose or float centered above your nose. Either way is okay. 17 Wear Adjust the arm height. Using both hands, raise or lower the arms to adjust the height of the visor. Your eyes are vertically centered in the screens. 18 Wear Slide the screens to center them over your pupils. 19 Wear Close one eye, and move the screen in front of the open eye until you see a clear, sharp view. Then, repeat for the opposite eye and screen. Finally, if you need to fine-tune the view, move the screens with both eyes open. Clear &

Complete Blurry Clipped Right Clipped Left 20 Wear Adjust the distance of the visor from your eyes. On both sides, rotate the Arm Dial forward to extend or backward to retract the visor. The screens are a comfortable viewing distance from your eyes or your prescription glasses if you wear them. 21 Use Adjust the tilt of the visor. If the visor doesnt tilt up fully, adjust the distance of the visor from your eyes, so its a little farther from your eyes. 22 Use eSight Corporation makes no claims about the suitability of eSight for any specific activity. While wearing eSight, do not drive, operate machinery, or engage in other visually or physically demanding activities that may cause injury or death. Do not operate motorized vehicles. Do not engage in visually or physically demanding activities. Do not operate power tools and machinery. 23 Use Visor Partially Up Visor Fully Down 24 Gestures Touch Pad Gestures Tap Tap and hold Swipe up or down Swipe forward/backward Button Gestures Press Press for half second Press for 2 seconds Press and hold 25 Control Via eSight 4 Basic Controls Touch Pad Zoom Contrast Photo Freeze 26 Control Via eSight 4 Advanced Controls Context Switch the Touch Pad Default Zoom/Contrast Context 2 Modes/Filters Context 3 Focus/Brightness Touch pad reverts to Zoom/Contrast if the touch pad is not used for a few seconds. Zoom Contrast Context 1

(Default) Context 2 Modes

(Indoors, Outdoors, Reading, TV/Theatre...) Filters

(Black on White, White on Black, Yellow on Blue, ...) Context 3 Focus Brightness Nearer Farther 27 Control Via eSight 4 Menu Navigation Open /

Close Menu or Go back Browse Select 28 Control Via Remote Basic Controls Photo Freeze Contrast Zoom Finder Reset Zoom Contrast Volume 29 Control Via Remote Advanced Controls Context Switch Directional Pad Filters/

Brightness Modes/

Focus Farther Filters/

Brightness Modes/

Focus Nearer Once for Modes / Filters A Second Time for Focus/Brightness Directional pad reverts to Zoom/Contrast if the directional pad is not used for a few seconds. 30 Control Via Remote Context Menu & Home Screen Navigation Select Back Open /Close Context Menu Directional Pad Go to Home Screen 31 Swap Swap batteries even while using eSight. Pull Out Pull out the discharged battery. Push In Immediately push in a fully charged battery. 32 Swap Insert batteries in the remote. Recycle Used Batteries 33 Charge

< 5%

5-20%

21-50%

51-70% 71-90% 91-100%

100-240V AC 34 Charge The Status Indicator shows the status of eSight 4. Booting Up Ready for Use Sleep Data Transfer Software Update Error 35 Clean Clean area with compressed air Clean the screens by wiping from the outside edge to the inside edge using a microfiber cloth. 36 Clean Clean the surface of eSight with a damp cloth. Remove the front and back halo padding, machine wash, air dry, and replace the halo padding. 37 Regulatory Notices Class 1 Laser Product This device contains a Class I Laser Product. Virtual Reality Statement eSight is not for use in immersive or partially immersive Virtual Reality applications. Read this guide for information on the proper use of the eyewear. State of California Proposition 65 Warning WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Wireless Device Regulatory Information Use on Aircraft WARNING: FCC and FAA regulations may prohibit airborne operation of radio-frequency wireless devices (such as Bluetooth and WiFi-enabled devices) because their signals could interfere with critical aircraft instruments. Ask the cabin crew before turning on eSight while on board. 38 Regulatory Notices Wireless Devices and Your Health eSight emits radio frequency electromagnetic energy. The level of energy emitted by eSight is less than the electromagnetic energy put out by other wireless devices such as mobile phones. eSight operates within the guidelines of radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community who continually review and interpret the extensive research literature. In some situations, the use of wireless devices may be restricted by the building owner or organization representative. Examples of such situations include:

Using wireless devices on-board airplanes, or Using wireless devices in any environment where the risk of interference with other devices is perceived as being harmful. If you are uncertain of the policy that applies to the use of wireless devices where you are (an airport, for example), ask for authorization to use eSight before you turn it on. FCC Specific Absorption Rate (SAR) Certification Information The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC-certified equipment. eSight meets the Human Exposure limits found in 47CFR2.1093. 39 Regulatory Notices US Federal Communications Commission (FCC) Interference Statement We, eSight Corporation, 515 Legget Drive, Suite 200, Ottawa, Ontario, Canada K2K 3G4, 1-855-837-4448, declare under our sole responsibility that eSight complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. The wireless technology in eSight has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If it is not used in accordance with instructions, the equipment may cause radio frequency interference to other devices and radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference

(which may be determined by turning the equipment on and off), the user (or qualified service personnel) should attempt to correct the problem by one or more of the following measure(s):

Reorient or relocate the affected device(s). Increase the separation between the equipment and the affected device(s). Connect the equipment into an outlet or circuit different from the one the affected device is connected to. Consult the point of purchase or service representative for further suggestions. 40 Regulatory Notices This product does not contain any user serviceable components. Any unauthorized product changes or modifications invalidate the warranty and all applicable regulatory certifications and approvals, including authority to operate this device. The wireless features of this device are restricted to indoor use due to its operation in the 5.15 to 5.25 GHz and 5.470 to 5.725 GHz frequency ranges. FCC requires the wireless features of this device to be used indoors mobile satellite systems. for the frequency ranges 5.15 to 5.25 GHz and 5.470 to 5.725 GHz to reduce the potential for harmful interference to co-channel High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device. No configuration controls are provided for this wireless device allowing any change in the frequency of operations outside the FCC grant of authorization for U.S operation according to Part 15.407 of the FCC rules. 41 Regulatory Notices Industry Canada This device complies with RSS-210 of the Industry Canada Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Caution

(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) The maximum antenna gain permitted for devices in the bands 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. 42 Regulatory Notices European Union This product must be used in strict accordance with the regulations and constraints in the country of use. For further information, contact the local office in the country of use. EU Specific Absorption Rate (SAR) Certification Information This device meets the EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The limits are part of extensive recommendations for the protection of the general public. These recommendations have been developed and checked by independent scientific organizations through regular and thorough evaluations of scientific studies. The unit of measurement for the European Councils recommended limit for mobile devices is the Specific Absorption Rate (SAR), and the SAR limit is 2.0 W/kg averaged over 10 grams of body tissue. It meets the requirements of the International Commission on Non-Ionizing Radiation Protection (ICNIRP). For body worn operation, this device has been tested and meets the ICNIRP exposure guidelines and the European Standard, for use with dedicated accessories. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines. The low band 5.15 to 5.35 GHz is for indoor use only. This equipment complies with the essential requirements of the European Union directive 2014/53/EU. For more details, request a copy of the Declaration of Conformity. 43 Regulatory Notices Correct Disposal Do not dispose of this product and its accessories with other household waste. Recycle them responsibly to protect human health and the environment and promote the sustainable reuse of material resources. Contact your retailer, or your local government office, for details of where you can take these items for environmentally safe electronics recycling. This product is RoHS compliant. Incident Reporting eSight is a medical device, and it is subject to additional monitoring. Report any safety incident related to the device to eSight Corporation and the medical authority regulating medical devices in your country. An incident means an event where the device directly or indirectly led, might have led, or might lead to a persons death, injury, or temporary or permanent deterioration in health. 44 Specifications Power Battery Proprietary rechargeable lithium-ion battery. Integrated rechargeable lithium-ion battery. Recharge with USB AC wall adapter (PSA10F-050Q) Input 100-240V AC 0.35A 50-60Hz Output 5V DC +/- 5% 2A and USB-A or USB-C Cable Connections Bluetooth Bluetooth 4.1 Pairs eSight 4 with eSight-supplied remote and/or other supported devices Wireless LAN Allows connecting to online services, device updates, and remote support 802.11b/g/n at 2.4 GigaHertz and 802.11a/n/ac at 5 GigaHertz HDMI Type D HDMI input that connects to supported video sources with HDMI Port Supported Resolutions and Frame Rates:

1080p/60 or 1080p/30 1080i/60 720p/60 or 720p/30 1280x960 540p/60 45 Specifications Operating Environment Operating Temperature 0C to 40C Storage Temperature

-20C to +45C Note: eSight is not intended for use in rain or heavy snowfall conditions. Care for eSight as you would any electronics device. 46 Contact Us eSight Customer Support (Canada and the United States) For questions and customer support, please contact us:

www.esighteyewear.com/contact 1-855-8eSight (1-855-837-4448)

* Follow the prompts to contact your eSight Coach. help@esighteyewear.com eSight Customer Support Outside Canada and the United States For questions and customer support, please contact your eSight Authorized Distributor or dispensing clinic directly. They are trained to provide full support in your local language and time zone. www.esighteyewear.com/support Warranty Follow Us

/eSightEyewear /esight_eyewear

/esighteyewear 47

Important Safety Information Using your eSight 3 safely 2016-09-26GuideCoversGSv3.0.indd 5 2016-10-04 1:54 PM Copyright 2016, eSight Corporation. All rights reserved. October 2016 No part of this publication may be reproduced without the express written permission of eSight Corporation. eSight Eyewear and eSight and associated images and symbols are trademarks of eSight Corporation. eSight is a registered trademark in Canada and the U.S. and may be pending or registered in other countries. Various U.S. and other patents pending. All other trademarks, registered trademarks, product names, and company names and/or logos cited herein, if any, are the property of their respective holders. eSight reserves the right to improve the contents of this document without notice. Table of Contents Warnings..................................................................................................1 Power Supply ............................................................................................................ 1 Lithium Battery ......................................................................................................... 2 Servicing ..................................................................................................................... 3 eSight-Approved Batteries, Chargers, and Accessories................................... 3 Improper Use and Storage ..................................................................................... 4 Improper Disposal .................................................................................................... 4 Cautions...................................................................................................5 Use Near Other Electronic Devices, Pacemakers and Hearing Aids ............ 5 Use in Hospitals, Aircraft, and Other Environments......................................... 6 Explosive Environments.......................................................................................... 7 Virtual Reality Statement.....................................................................7 Proper Care and Use.............................................................................8 Airport Security and Your eSight 3................................................. 11 Class 1 Laser Product ........................................................................ 11 Product Emissions Compliance ....................................................... 11 Wireless Adapter Regulatory Information.................................... 12 Use on Aircraft....................................................................................................... 12 Wireless Adapter and Your Health.................................................................... 13 US Federal Communications Commission (FCC) Interference Statement 14 Industry Canada/Canada dIndustrie................................................................. 16 European Union..................................................................................................... 18 Correct Disposal ................................................................................. 19 i Important Safety Information Please read this important safety information before you use the device. It contains general safety information for your device. Follow the warning and caution information to prevent injury to yourself or others and to prevent damage to your device. The term 'device' refers to the eSight 3 and its battery, charger, the items supplied with the product, and any eSight-approved accessories used with the product. Warnings Failure to comply with safety warnings and regulations can cause serious injury or death. Power Supply Use only the power supply provided. Using an unapproved power supply may cause a serious injury, a fire, or cause the battery to explode. Do not use damaged power supplies, cords, plugs, or loose electrical sockets. Unsecured connections can cause electric shock or fire. 1 Important Safety Information Do not plug in the device with wet hands or disconnect the charger by pulling the cord. Doing so may result in electrocution. Do not bend or damage the power cord. Doing so may cause electric shock or fire. Do not short-circuit the power supply or the device. Doing so may cause electric shock or fire, or the battery may malfunction or explode. Do not use your device outdoors during a thunderstorm Doing so may result in electric shock or device malfunction. Lithium Battery Do not expose the battery to damaging environments. Do not use the lithium battery in humid, wet, or corrosive environments. Do not place or store your device in or near a heat source, in a high temperature location, in strong direct sunlight, in a microwave oven, or in a pressurized container. Do not expose your device to temperatures over 60 C (140 F). Damaging environments may cause the battery to leak, overheat, explode, or ignite and cause injury and/or damage. 2 Important Safety Information Do not pierce, open, or disassemble the battery. If the battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical attention immediately. Do not attempt to service or replace the battery provided with your device. The battery is not serviceable. Do not attempt to replace it. Serious damage may occur. Servicing Do not attempt to service this device yourself. Opening or removing covers may expose you to dangerous energy points or other risks. Refer all servicing to qualified service personnel. eSight-Approved Batteries, Chargers, and Accessories Use manufacturer-approved batteries, chargers, and accessories Use only eSight-approved chargers and batteries with your device. Using unapproved chargers or batteries may cause a fire or cause the battery to explode. Using an incompatible battery and charger can cause serious injuries, damage to your device, or device malfunctions. 3 Important Safety Information Improper Use and Storage Do not use or store your device in areas with high concentrations of dust or airborne materials. Dust or foreign materials can cause your device to malfunction and may result in fire or electric shock. Do not allow the device connections and cables to come in contact with conductive materials Conductive materials, such as liquids, dust, metal powders, and pencil leads, may cause a short circuit or corrosion of the terminals, which may result in an explosion or fire. Store your device only on flat surfaces If your device falls, it may be damaged. Improper Disposal Never dispose of the battery or device in a fire. The device may explode when overheated. Follow all local regulations when disposing of a used consumer electronics device. Never crush or puncture the device. High external pressure can lead to an internal short circuit and overheating. 4 Important Safety Information Do not dispose of the device in a landfill. Safely dispose of this product, at the end of its useful life, according to applicable local laws, regulations, and procedures for electrical and electronic equipment waste. See Correct Disposal on page 19. Contact eSight for more information. Cautions Failure to comply with safety cautions and regulations can cause injury or property damage Use Near Other Electronic Devices, Pacemakers and Hearing Aids Do not use your device near other electronic devices Most electronic devices use radio frequency signals. Your device may interfere with other electronic devices. Avoid using your device near pacemakers Avoid using your device within 15 centimeters (6 inches) of a pacemaker, if possible, as your device can interfere with the pacemaker. Do not carry the device near your pacemaker when the device is switched on. If you suspect interference with your pacemaker, switch off the device and move it. 5 Important Safety Information Avoid using your device near hearing aids Avoid using your device near hearing aids. Some digital wireless devices may interfere with some hearing aids. If you use a hearing aid, contact the manufacturer before using your device to determine whether or not your hearing aid will be affected by radio frequencies emitted by the device. Use in Hospitals, Aircraft, and Other Environments Do not use the wireless features of your device in a hospital, on an aircraft, or in other environments near equipment that can be interfered with by radio frequency. Do not use the wireless features of your device in a healthcare facility or on an aircraft. Place your device in Airplane Mode. Your device may interfere with improperly protected medical devices. If you use medical equipment, contact the equipment manufacturer before using your device to determine whether or not the equipment will be affected by radio frequencies emitted by your device. Your device may interfere with the electronic navigational instruments on aircraft. Make sure the device is turned off during takeoff and landing. After takeoff, you can use the device in Airplane Mode if allowed by aircraft personnel. Do not use your device near equipment that emits radio frequencies, such as sound systems or radio towers. Radio frequencies may cause your device to malfunction. 6 Important Safety Information In some situations or environments, the use of wireless radio devices is restricted. When in doubt, ask for authorization prior to using the wireless features on your device. Explosive Environments Turn off the device in potentially explosive environments Always comply with regulations, instructions, and signs in potentially explosive environments. Do not use your device at refueling points (gas stations), near fuels or chemicals, or in blasting areas. Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as the device, its parts, or accessories. If you notice strange smells or sounds coming from your device or the battery, or if you see smoke or liquids leaking from the device or battery, stop using the device immediately and take it to an eSight Service Center. Failure to do so may result in injury, fire, or explosion. Virtual Reality Statement eSight 3 is not for use in immersive or partially immersive Virtual Reality applications. Please refer to the User Guide for information on the proper use of the eyewear. 7 Important Safety Information Proper Care and Use Keep your device dry Humidity and liquids may damage the parts or electronic circuits in your device. Do not turn on your device if it is wet. If your device is already on, turn it off (if the device will not turn off, leave it as-is). Then, dry the device with a towel and contact eSight for service. Do not store your device near magnetic fields Your device may malfunction or the battery may discharge from exposure to magnetic fields. Do not use your device or applications for a while if the device is overheated Prolonged exposure of your skin to an overheated device may cause low temperature burn symptoms, such as red spots and pigmentation. Do not use the light close to the eyes of people or pets Using a light close to the eyes may cause temporary loss of vision or damage to the eyes. 8 Important Safety Information Protect your hearing and ears when using headphones Excessive exposure to loud sounds can cause hearing damage. Exposure to loud sounds may distract your attention and cause an accident. Always turn the volume down before connecting the headphones to an audio source and use only the minimum volume setting necessary to hear. Use caution when using the device while walking or moving Always be aware of your surroundings to avoid injury to yourself or others. Make sure the headset cable does not become entangled in your arms or on nearby objects. Discontinue use of the device if you develop a skin allergy If you are allergic to the materials that come in contact with your skin, you may experience itching, eczema, or swelling of the skin. When this happens, stop using the device and consult your physician. Do not drop your device or cause impacts to your device Your device may be damaged or may malfunction. 9 Important Safety Information Ensure maximum battery and charger life Follow all instructions to ensure the longest lifespan of your device and battery. Overcharging the battery may shorten battery life. Over time, an unused device will discharge and must be recharged before use. Disconnect the charger from power sources when not in use. Leaving batteries unused over time may reduce their lifespan and performance. Handle SD Cards and Cables With Care When inserting a card or connecting a cable to your device, make sure that the card is inserted or the cable is connected correctly. Do not remove a card while the device is transferring or accessing information, as this could result in loss of data and/or damage to the card or device. Protect cards from strong shocks, static electricity, and electrical noise from other devices. Do not touch gold-colored contacts or terminals with your fingers or metal objects. If dirty, wipe the card with a soft cloth. Inserting a card or connecting a cable by force or improperly may result in damage to the device and/or cable. 10 Important Safety Information Airport Security and Your eSight 3 At airport security, you may be asked to remove your eyewear as part of the security screening process. Inform the security officer that you have low vision and may require assistance with the screening process. If you travel with supporting documentation describing your medical condition, present it to officer. Politely ask the officer to reunite you with your eyewear immediately after it is screened. Class 1 Laser Product This device contains a Class I Laser Product. Product Emissions Compliance This equipment generates, uses, and can radiate radio frequency energy. It also contains rare-earth magnets. The equipment may cause radio frequency or magnetic interference to other devices and radio communications. To provide reasonable protection against such interference, this product complies with CISPR-22, CISPR-24, and FCC Part 15, Subparts

'B' and 'C' standards for radiated emissions. However, there is no guarantee that interference will not occur in a particular installation. 11 Important Safety Information If this equipment is found to cause interference (which may be determined by turning the equipment on and off), the user (or qualified service personnel) should attempt to correct the problem by one or more of the following measure(s):

Reorient or relocate the affected device(s) Increase the separation between the equipment and the affected device Consult the point of purchase or service representative for further suggestions The manufacturer is not responsible for any interference caused by using other than recommended interconnect cables or by unauthorized changes or modifications to this equipment. Changes or modifications are not authorized. Wireless Adapter Regulatory Information Use on Aircraft Caution FCC and FAA regulations may prohibit airborne operation of radio-

frequency wireless devices (wireless adapters) because their signals could interfere with critical aircraft instruments. Ask the cabin crew before turning on the wireless adapter while on board. 12 Important Safety Information Wireless Adapter and Your Health The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the eSight wireless adapter is less than the electromagnetic energy put out by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines of radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community who continually review and interpret the extensive research literature. In some situations, the use of the wireless adapter may be restricted by the building owner or organization representative. Examples of such situations include Using the wireless adapter on-board airplanes, or Using the wireless adapter in any environment where the risk of interference with other devices is perceived as being harmful. If you are uncertain of the policy that applies to the use of wireless adapters where you are (an airport, for example), ask for authorization to use the adapter before you turn it on. FCC Specific Absorption Rate (SAR) Certification Information The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC-certified equipment. The wireless adapter meets the Human Exposure limits found in OET Bulletin 65. 13 Important Safety Information US Federal Communications Commission (FCC) Interference Statement We, eSight Corporation, 515 Legget Drive, Suite 200, Ottawa, Ontario, Canada K2K 3G4, 1-855-837-4448, declare under our sole responsibility that eSight 3 complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it is not used in accordance with instructions, the equipment may cause radio frequency interference to other devices and radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment is found to cause interference (which may be determined by turning the equipment on and off), the user (or qualified service personnel) should attempt to correct the problem by one or more of the following measure(s):

Reorient or relocate the affected device(s) 14 Important Safety Information Increase the separation between the equipment and the affected device Connect the equipment into an outlet on circuit different from the one the affected device is connected to. Consult the point of purchase or service representative for further suggestions This product does not contain any user serviceable components. Any unauthorized product changes or modifications invalidate the warranty and all applicable regulatory certifications and approvals, including authority to operate this device. The wireless features of this device are restricted to indoor use due to its operation in the 5.15 to 5.25 GHz and 5.470 to 5.725 GHz frequency ranges. FCC requires the wireless features of this device to be used indoors for the frequency ranges 5.15 to 5.25 GHz and 5.470 to 5.725 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device. No configuration controls are provided for this wireless adapter allowing any change in the frequency of operations outside the FCC grant of authorization for U.S operation according to Part 15.407 of the FCC rules. 15 Important Safety Information Industry Canada/Canada dIndustrie This device complies with RSS-210 of the Industry Canada Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes:

Le dispositif ne doit pas produire de brouillage prjudiciable. Ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution

(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-

channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit;

and

(iii) The maximum antenna gain permitted for devices in the bands 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-

to-point and non point-to-point operation as appropriate. 16 Important Safety Information

(iv) Users should also be advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement

(i) Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) Le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5150-5250 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e.;

(iii) Le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 57255825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour l'exploitation point point et non point point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d ., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 17 Important Safety Information European Union This product must be used in strict accordance with the regulations and constraints in the country of use. For further information, contact the local office in the country of use. EU Specific Absorption Rate (SAR) Certification Information This device meets the EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The limits are part of extensive recommendations for the protection of the general public. These recommendations have been developed and checked by independent scientific organizations through regular and thorough evaluations of scientific studies. The unit of measurement for the European Council's recommended limit for mobile devices is the

"Specific Absorption Rate" (SAR), and the SAR limit is 2.0 W/kg averaged over 10 grams of body tissue. It meets the requirements of the International Commission on Non-Ionizing Radiation Protection

(ICNIRP). For body worn operation, this device has been tested and meets the ICNIRP exposure guidelines and the European Standard, for use with dedicated accessories. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines. The low band 5.15 to 5.35 GHz is for indoor use only. This equipment complies with the essential requirements of the European Union directive 1999/5/EC. For more details, request a copy of the Declaration of Conformity. 18 Important Safety Information Correct Disposal

(Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories, or literature indicates that the product and its electronic accessories (e.g. charger, headset, controller, cables) should not be disposed of with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. This product is RoHS compliant. 19 4000353 Rev. 3 Copyright 2016, eSight Corporation.

FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 Model: ITCNFA324 External Photos Top Side Bottom Side FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 Module Model Number: ITCNFA324 Host Model Numbers for eSight Head Mounted Displays: 3001000, 3001001, 3001002, 3001003, 3001004, 3001005, 3001006, 3001007, 3001008 and 3001009. The only difference between model numbers is the enclosure color. Screen capture of display on host device to satisfy e-labeling requirements. Screen capture of display menu to get to About Menu on host device.

FCC ID: QOQ11 IC: 5123A-11 HVIN: BGM11S1A Secondary BT Module Labeling Secondary BT Module Location on Right Temple Arm PCBA Close Up of Secondary BT Module Label FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 Model: ITCNFA324 External Photos Top Side Bottom Side FCC ID: 2AFDI-ITCNFA324 IC: 9049A-ITCNFA324 Module Model Number: ITCNFA324 Host Model Numbers for eSight Head Mounted Displays: 300200x where x signifies the color of the case. The only difference between model numbers is the enclosure color. The image below is a screen capture from the host device from the About menu to satisfy e-labeling requirements.

FXP840 Patent Pending 3 3 3 M M M This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre 301055-14April 22, 2019

FXP840 Patent Pending 3 3 3 M M M This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre 301055-12February 21, 2019

FXP840 Freedom Series super small Wi-Fi 2.4/5.8/7.125GHz flexible monopole antenna Freedom Part No:

FXP840.07.0055B Description:

with Wi-Fi 6 capabilities Features:

Wi-Fi (Including Wi-Fi 6) 2.4-2.5, 4.9-5.8, 5.9-7.125 GHz Flexible and Tiny - Ultra Low Profile Adheres directly inside of product plastic or glass housing Form factor and cable routing convenient for integration I-PEX MHF I Connector (U.FL compatible) 55mm 0.81mm mini-coaxial cable Dimensions: 14*5*0.1mm RoHS & Reach Compliant SPE-12-8-115-J 3 5 6 9 11 12 13 1. 2. Introduction Specifications 3. Antenna Characteristics 4. Radiation Patterns 5. Mechanical Drawing 6 m. Packaging Changelog Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Taoglas reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. SPE-12-8-115-J www.taoglas.com 2 Introduction Introduction Introduction Introduction 1. 1. 1. 1. 1. 1. 1. 1. Introduction Introduction Introduction The patent pending FXP840 is a super small monopole ultra-low profile antenna for 2.4/4.9-5.8/5.8-7.125 Introduction GHz. This antenna is designed for C-V2X, DSRC, V2V, Wi-Fi(including Wi-Fi 6), Bluetooth, ZigBee and other applications in these bands. This Taoglas patent pending antenna is unique in the market because it is made from poly-flexible material, has a tiny form factor (14mm*5.0mm*0.1mm) and has double-sided 3M tape for easy peel and stick mounting. The cable routes conveniently directly out of the bottom of the antenna, reducing the volume the antenna takes up in the device to an absolute minimum compared to other designs. The FXP840 is the ideal all-round antenna solution for fitting into narrow spaces and still maintaining high performance, for example on the inside top or adjacent side applied directly to the plastic housing of LCD monitors, tablets, smartphones. Many module manufacturers specify peak gain limits for any antennas that are to be connected to that module. Those peak gain limits are based on free-space conditions. In practice, the peak gain of an antenna tested in free-space can degrade by at least 1 or 2dBi when put inside a device. So ideally you should go for a slightly higher peak gain antenna than mentioned on the module specification to compensate for this effect, giving you better performance. Upon testing of any of our antennas with your device and a selection of appropriate layout, integration technique, or cable, Taoglas can make sure any of our antennas peak gain will be below the peak gain limits. Taoglas can then issue a specification and/or report for the selected antenna in your device that will clearly show it complying with the peak gain limits, so you can be assured you are meeting regulatory requirements for that module. SPE-12-8-115-J www.taoglas.com 3 For example, a module manufacturer may state that the antenna must have less than 2dBi peak gain, but you dont need to select an embedded antenna that has a peak gain of less than 2dBi in free-space. This will give you a less optimized solution. It is better to go for a slightly higher free-space peak gain of 3dBi or more if available. Once that antenna gets integrated into your device, performance will degrade below this 2dBi peak gain due to the effects of GND plane, surrounding components, and device housing. If you want to be absolutely sure, contact Taoglas and we will test. Choosing a Taoglas antenna with a higher peak gain than what is specified by the module manufacturer and enlisting our help will ensure you are getting the best performance possible without exceeding the peak gain limits. The cable and connector are fully customizable, for further information please contact your regional Taoglas customer support team. SPE-12-8-115-J www.taoglas.com 4 2. Specifications 3. Antenna Characteristics2. Specifications Wi-Fi Electrical Band Frequency (MHz) Impedance Polarization Radiation Pattern Efficiency

(%) Average Gain

(dB) Peak Gain

(dBi) Max Input Power 3. Antenna Characteristics 2.4GHz Wi-Fi 2400~2500 53.7

-2.7 3.6 1.3 5.8GHz Wi-Fi 5150~5850 34.1

-4.8 50 Linear Omni-Directional 2W 5925~7125 7.1GHz Wi-Fi 6 4. Antenna Radiation Patterns3. Antenna Characteristics2. Specifications 59.1

-2.3 2.7 Mechanical Dimenions 14 x 5 x 0.1 mm 3. Antenna Characteristics2. Material Specifications Polymer Connector I-PEX MHF I (U.FL Compatible) 3. Antenna Characteristics Cable 55mm of 0.81mm Weight 4. Antenna Radiation Patterns3. Antenna Operation Temperature

-40C to +85C Environmental 1g Yes Yes

-40C to +85C Non-condensing 65C 95% RH Characteristics Storage Temperature Humidity RoHS Compliant 4. Antenna Radiation Patterns REACH Compliant 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns3. Antenna Characteristics2. Specifications SPE-12-8-115-J www.taoglas.com 5 5200 4. Antenna Radiation Patterns3. Antenna 3200 2200 3700 4200 4700 2700 Frequency (MHz) 5700 6200 6700 7200 3. Antenna Characteristics 3.1 Return Loss 4. Antenna Radiation Patterns3. Antenna Characteristics 4. Antenna Radiation Patterns

-6 4. Antenna Radiation Patterns3. Antenna Characteristics

-13 S11 Characteristics 3.2 VSWR 10 4. Antenna Radiation Patterns 9 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns 4

) B d

s s o L n r u t e R 0

-1

-2

-3

-4

-5

-7

-8

-9

-10

-11

-12

-14

-15

-16 R W S V 8 7 6 5 3 2 1 4. Antenna Radiation Patterns3. Antenna VSWR Characteristics 0 2200 2700 3200 3700 4200 5200 5700 6200 6700 7200 4700 Frequency (MHz) 4. Antenna Radiation Patterns3. Antenna SPE-12-8-115-J www.taoglas.com 6 Characteristics 3.3 Efficiency 100 Efficiency (%) 2700 3200 3700 4200 5200 5700 6200 6700 7200 4700 Frequency (MHz) 3.4 Peak Gain Peak Gain (dBi)

y c n e i c i f f E 90 80 70 60 50 40 30 20 10 0 2200 i

) i B d

n a G k a e P 6 5 4 3 2 1 0

-1

-2

-3

-4

-5 SPE-12-8-115-J 2200 2700 3200 3700 4200 4700 5200 5700 6200 6700 7200 Frequency (MHz) www.taoglas.com 7 3.5 Average Gain Average Gain (dB) 2200 2700 3200 3700 4200 4700 5200 5700 6200 6700 7200 Frequency (MHz) i

) B d

n a G e g a r e v A 0

-1

-2

-3

-4

-5

-6

-7

-8

-9

-10 SPE-12-8-115-J www.taoglas.com 8 4. Radiation Patterns 4. 4. Antenna Radiation Patterns Test Setup 2mm ABS 4.1 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns Y X Z 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns 4. Antenna Radiation Patterns SPE-12-8-115-J www.taoglas.com 9 4.2 2D Radiation Patterns 2400-2500MHz XZ Plane XY Plane X 5 0

-5

-10

-15

-20

-25

-30 XY Plane X 5 0

-5

-10

-15

-20

-25

-30 Y 2400 MHz 2450 MHz 2500 MHz Y 5000 MHz 5500 MHz 6000 MHz 6500 MHz 7000 MHz Z 5 0

-5

-10

-15

-20

-25

-30 Z 5 0

-5

-10

-15

-20

-25

-30 5000-7000MHz XZ Plane X 2400 MHz 2450 MHz 2500 MHz X 5000 MHz 5500 MHz 6000 MHz 6500 MHz 7000 MHz YZ Plane Y 5 0

-5

-10

-15

-20

-25

-30 YZ Plane Y 5 0

-5

-10

-15

-20

-25

-30 2400 MHz 2450 MHz 2500 MHz Z Z 5000 MHz 5500 MHz 6000 MHz 6500 MHz 7000 MHz SPE-12-8-115-J www.taoglas.com 10 5. Mechanical Drawing (Units: mm) 6. Packaging5. Mechanical Drawing 6. Packaging Drawing 6. Packaging 7. Application Note6. Packaging5. Mechanical 6. Packaging5. Mechanical Drawing 7. Application Note6. Packaging 7. Application Note 7. Application Note6. Packaging 7. Application Note6. Packaging5. Mechanical Drawing 6. Packaging5. Mechanical Drawing SPE-12-8-115-J www.taoglas.com 11 6. Packaging 6. Packaging5. Mechanical Drawing 1pcs FXP840.07.0055B per PE Bag Weight - 1g 6. Packaging 7. Application Note6. Packaging5. Mechanical 2000pcs FXP840.07.0055B per carton Dimensions - 230*160*175mm Weight - 6.8Kg Drawing 6. Packaging5. Mechanical Drawing 6. Packaging 7. Application Note6. Packaging 7. Application Note 7. Application Note6. Packaging 7. Application Note6. Packaging5. Mechanical Drawing 6. Packaging5. Mechanical Drawing SPE-12-8-115-J www.taoglas.com 12 Changelog for the datasheet SPE-12-8-115 - FXP840.07.0055B Revision: J (Current Version) Date:

2020-09-04 Changes:

Updated Wi-Fi 6 info Changes Made by:

Jack Conroy Previous Revisions Revision: I Date:

Changes:

2017-03-08 ECR-18-8-259 Revision: D Date:

Changes:

2012-11-19 Packaging Details Updated Changes Made by:

Russell Meyler Changes Made by:

Aine Doyle Revision: H Revision: C Date:

Changes:

2018-06-27 Updated Peak Gain Date:

Changes:

2012-10-02 Updated Drawing Changes Made by:

Jack Conroy Changes Made by:

Aine Doyle Revision: G Revision: B Date:

Changes:

2018-06-27 Updated Peak Gain Date:

Changes:

2012-09-27 Packaging Details Updated Changes Made by:

Carol Faughnan Changes Made by:

Aine Doyle Revision: F Date:

2017-05-07 Changes:

PCN-17-8-081 Revision: A (Original First Release) Date:

2012-09-13 Notes:

Changes Made by:

Aine Doyle Author:

Technical Writer Revision: E Date:

Changes:

2017-03-08 Added Note on Intro Changes Made by:

Aine Doyle SPE-12-8-115-J www.taoglas.com 13 www.taoglas.com SPE-12-8-115-J www.taoglas.com Taoglas 14

FXP840 Patent Pending 3 3 3 M M M This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre 301055-10June 21, 2019

Class-II Permissive Change Application Authorization Letter Date: 2022-01-10 Ref: Class-II Permissive Change Authorization to FCC ID: 2AFDI-ITCNFA324, IC ID: 9049A-ITCNFA324 To Whom it may concern:

This letter grants authorization for the representative of Thales Avionic, Inc. to apply to FCC for the Class-II Permissive Change as specified under 47CFR2.933 of the FCC rules. This authorization applies to Lantronix FCC ID: 2AFDI-ITCNFA324 (Original Grant date: 12/10/2015) and IC ID: 9049A-ITCNFA324. The major change filed under this application are:

Change #1: This change is to add an additional antenna type: Taoglas FXP840 flexible monopole antenna with 3.6 dBi gain at 2.4 - 2.5 GHz and 1.3 dBi gain at 5.15 - 5.85 GHz. The new antenna was used in the Thales Avionics, Inc. WMC devices: Model 186521-20x and 187554-10x where x is the different in SSD size. Sincerely yours,

Fathi Hakam / VP of Engineering Tel: +1 (949) 453-3990 Fax: +1 (949) 453-3995 E-mail: fhakam@lantronix.com

The Smart Choice for the Connected Airline WIRELESS MODE CONTROLL ER Product Description Revised: Mar. 2022 Thales Avionics, Inc. 51 Discovery Irvine, California 92618 USA +1 949 790 2500 www.thales-ifec.com This document and any data included are the property of Thales Avionics, Inc. and cannot be reproduced, disclosed or utilized without the companys prior written approval. CONFIDENTIAL AND PROPRIETARY NOTICE Use of this document is limited to the following limitations:

This document is the property of Thales Avionics, Inc., and contains proprietary and confidential information. This copy is furnished with the express condition that its content shall not be reproduced, wholly or in part, nor disclosed to any other party, nor be used wtihout the written permission of Thales Avionics, Inc. Moreover, the document shall be returned upon request. AVANT, FlytLIVE, FlytCARE, TopSeries, TopEffects and Thales InFlyt Experience are marks of Thales Avionics, Inc. iPad, iPhone and Mac OS are registered trademarks of Apple, Inc. Android is a trademark of Google Inc. Every effort has been made to ensure the accuracy, reliability and completeness of the information contained in this document. The content contained herein is subject to change and Thales Avionics, Inc. is not responsible for errors or omissions, and reserves the right to change the information without notice. Wireless Mode Controller Product Description WIRELESS MODE CONTROLLER TABLE OF CONTENTS Introduction ............................................................................................................................. 5 Features .................................................................................................................................... 5 Product Overview ............................................................................................................................... 5 Standard Features ............................................................................................................................... 7 Operation Modes ................................................................................................................................ 7 Summary of Benefits ............................................................................................................... 8 FIGURES AND TABLES Table 1 Standard Features and Specs .............................................................................................................. 7 Figure 1 - Premium Seats LRUs Configuration .. 5 Figure 2 - 10.1" WMC Tablet & Dock Station 6 Figure 3 - 13.3" WMC Tablet & Dock Station 6 2022 THALES AVIONICS, INC. Page 3 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Wireless Mode Controller Product Description THIS PAGE INTENTIONALLY BLANK 2022 THALES AVIONICS, INC. Page 4 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Wireless Mode Controller Product Description WIRELESS MODE CONTROLLER INTRODUCTION The Wireless Mode Controller (WMC) Product Line includes tablet devices and docking stations. First-

class and business-class passengers will use the tablet as a second screen device to:

1. Augment the primary screen, Thales SVDUs, with information and additional content. 2. Deliver Audio/Video on Demand (AVOD) application and services. 3. Application platform for Thales and third-party applications. 4. Communication between the first-class or business-class passenger and an airline flight crew. 5. Control of on-wing subsystems. FEATURES Product Overview With the introduction of our 6th Generation product we have made several changes to the product line. The Wireless Mode Controllers (WMC) are the new LRUs addition to the 6th Generation of the Avant IFE system. With the support of the WiFi and Bluetooth technologies, the WMC will provide the premium passengers the experience of wireless access to the Inflight Entertainment Applications such as: Video/Audio on Demand, communication to the flight crew as well as other premium passenger (Video chat), Remote control of the on-wing subsystem (seat control, window shade control, lightning control, wireless headphone, ect). Figure 1 - Premium Seats LRUs Configuration 2022 THALES AVIONICS, INC. Page 5 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Wireless Mode Controller Product Description Figure 2 - 10.1 WMC Tablet & Dock Station Figure 3 - 13.3 WMC Tablet & Dock Station 2022 THALES AVIONICS, INC. Page 6 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Wireless Mode Controller Product Description 10.1 WMC (186521-20x) 13.3 WMC (187554-10x) 10.1 1920x1080 5 Point Multi-Touch LCD on/off, Volume up/down WiFi 802.11 B/G/N/AC 13.3 1920x1080 25Wh Lithium-Ion Polymer (LiPo) Docking Station: Battery charging, 1Gb Ethernet interface with IFE Bluetooth 4.1 Headphone Jack Front and Rear system Android 7.1.1 Qualcom 820, 4 Core 128GB SSD or 512GB SSD 4 GB Tablet: 2.2 lbs Dock: 1.5 lbs Standard Features Features LCD Diagonal Dimensions LCD Resolution Capacitive-touch Screen Buttons Wireless Connector Camera Battery Remote Peripheral Interfaces Operating System Microprocessor Storage RAM Weight (est.) Power (est.) Tablet: 2.9 lbs Dock: 2.25 lbs Tablet docked: 30W (typical), 60W (max) Tablet undocked: 8W (typical), 12W (max) MTBF (on-wing hours) Tablet: 20,000h ; Dock: 30,000h Table 1 Standard Features and Specs The Wireless Mode Controller has two modes of operation: tablet docked and tablet undocked. Operation Modes 1. Tablet docked (Wired mode) During taxi, take-off, landing, and turbulence flight phases, the tablet shall be docked and locked. Passenger cannot remove the tablet from the dock. The communication between the tablet and the Inflight Entertainment System (IFE) is via the 1Gbits Ethernet port. The tablet and the dock are powered by the +28VDC Seat Power Unit. Battery is charging by the dock (if battery is not fully charged) IFE applications and communication with IFE system is via 1Gbits Ethernet 2. Tablet undocked (Wireless mode) During other phases of the flight (climbing, cruising), tablet will be unlocked so passenger can undock the tablet and use it for the available IFE applications on cabin 2022 THALES AVIONICS, INC. Page 7 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Wireless Mode Controller Product Description The WiFi and Bluetooth will be enabled to allow the tablet to wirelessly communicate with the IFE system The tablet will be powered by the built-in battery SUMMARY OF BENEFITS The latest IFE Avant GEN6 LRUs were designed to not only improve the passenger experience, but also cut costs and increase the bottom line. The Wireless Mode Controller can serve as an entertainment, information or retail platform providing passengers access to an expansive marketplace filled with the most recent Shopping Catalogs, Movies, Destination Information and more. Other improved functions and benefits include Increased usability flexible placement of remote peripherals in business and first-class seats Improved passenger experience The Seat Environment Control and Inflight Entertainment Apps are wireless accessible via WiFi & Bluetooth Responsive user interaction latest system-on-chip (SOC) microprocessor that has the horsepower to run the most up-to-date software, off-load video and audio processing and manage network traffic to provide fast response to user interaction including video game control and video-on-demand (VOD) services 2022 THALES AVIONICS, INC. Page 8 of 9 This document and any data included are the property of Thales Avionics and cannot be reproduced, disclosed or utilized without the Companys prior written approval. March 2022 Thales InFlyt Experience 58 Discovery Irvine, CA 92618

+1 949 790 2500

Authority to Act as Agent Date: 02/07/2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

RF Exposure Lab is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, which include FCC benefits. This authorization is applicable to the product:

FCC ID: 2AFDI-ITCNFA324 Agency Agreement Expiration Date: 12/31/2020 y 7 Sincerely, Gi 4 i J uv LZ LAw By: George Reznik A ff JK ignature) Title: cro [7 On behalf of: Intrinsye Technologies Corp. Telephone: 604-801-6461 Fax: 604-801-6417 e-mail: greznik@intrinsyc.com

R for Confidentiali Date: 02/10/2020 Subject: Confidentiality Request for FCC ID: 2AFDI-ITCNFA324 Pursuant to FCC 47 CRF 0.457(d) the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Type of exhibit Short Term XX] Permanent | Tune Up Procedure Operation Description/Theory of Operation Intrinsye Technologies Corporation has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to

"competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Sincerely, By: George Reznik Title: cTO On behalf of: Intrinsye Technologies Corp. Telephone: 604-801-6461 Fax: 604-801-6417 e-mail: greznik@intrinsyc.com

Date: March 11, 2020 Request for Modular Approval Subject: Manufacturers Declaration for - Modular Approval

- Split Modular Approval

- Limited Modular Approval - Limited Split Modular Approval Confidentiality Request for: ______2AFDI-ITCNFA324______ For Items Marked NO(*), the Limited Module Description Must be Filled Out on the Following Pages Modular Approval Requirement Requirement Met 8 Basic Requirements FCC Part 15.212(a)(1) 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with FCC limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 15.212(a)(1)(i)

- YES - NO(*) Details: The module contains a metal shield which covers all RF components and circuitry. The shield is located on the top side of the board. See photo provided with this application. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with FCC requirements under conditions of excessive data rates or over-modulation. 15.212(a)(1)(ii)

- YES - NO(*) Details: Data to the modulation circuit is buffered on the module; please refer to the operational description document filed with this application for full description. 3. The modular transmitter must have its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 15.212(a)(1)(iii)

- YES - NO(*) Details: The module contains its own power supply regulation and the rf reference oscillator is contained within the module. Please refer to the schematics and operational description documents filed with this application for full description. 4. The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv)

- YES - NO(*) Details: The module connects to its antenna via using an UFL type connector. This antenna connector is a non-standard connector. The antenna tested was a PIFA type and the data sheet is included in the application. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 15.212(a)(1)(v)

- YES - NO(*) Details: Test data contained in this application is for the device tested as a stand-alone device connected externally to a PC. See test set-up photographs filed with this application. 6. The modular transmitter must be labeled with its own FCC ID number, or use an electron display

(see KDB Publication 784748). Modular Approval Requirement Requirement Met If using a permanently affixed label with its own FCC ID number, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID: XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 15.212(a)(1)(vi)

- YES - NO(*) Details: The module is appropriately labeled (refer to the label and label location drawings contained within this application). Information to the integrator of this device regarding the labeling requirements for the host system is contained in the instructions provided with the module. 7. The modular transmitter must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 15.212(a)(1)(vii)

- YES - NO(*) Details: The module complies with FCC Part 15C requirements. Instructions to the OEM installer are provided in the installation manual filed with this application.>

8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. 15.212(a)(1)(viii)

- YES - NO(*) Details: The module meets the requirements for a mobile/portable device that may be used at separation distances of more than 12mm from the human body. Refer to the RF Exposure test report submitted with this application. Limited Module Description When Applicable

* If a module does NOT meet one or more of the above 8 requirements, the applicant may request Limited Modular Approval (LMA). This Limited Modular Approval (LMA) is applied with the understanding that the applicant will demonstrate and will retain control over the final installation of the device, such that compliance of the end product is always assured. The operating condition(s) for the LMA; the module is only approved for use when installed in devices produced by grantee. A description regarding how control of the end product, into which the module will be installed, will be maintained by the applicant/manufacturer, such that full compliance of the end product is always ensured should be provided here. Details: N/A Details: N/A Details: N/A Software Considerations KDB 594280 / KDB 442812 (One of the following 2 items must be applied) Requirement Requirement Met 1. For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description must be provided about how such control is implemented to ensure prevention of third-party modification; see KDB Publication 594280.

- Provided in Separate Cover Letter

- N/A Details: <example The firmware of the device cannot be modified or adjusted by the end user as described in a separate cover letter filed with this application. >

2. For Software Defined Radio (SDR) devices, transmitter module applications must provide a software security description; see KDB Publication 442812.

- Provided in Separate Cover Letter

- N/A Split Modular Requirements Requirement Provided in Manual 1. For split modular transmitters, specific descriptions for secure communications between front-end and control sections, including authentication and restrictions on third-party modifications; also, instructions to third-party integrators on how control is maintained.

- Provided in Separate Cover Letter

- N/A OEM Integration Manual Guidance KDB 996369 D03 Section 2 Clear and Specific Instructions Describing the Conditions, Limitations, and Procedures for third-parties to use and/or integrate the module into a host device. Requirement Is this module intended for sale to third parties?

- YES

- No, If No, and LMA applies, the applicant can optionally choose to not make the following detailed info public. However there still needs to be basic integration instructions for a users manual and the information below must still be included in the operational description. If the applicant wishes to keep this info confidential, this will require a separate statement cover letter explaining the module is not for sale to third parties and that integration instructions are internal confidential documents. Items required to be in the manual See KDB 996369 D03, Section 2 As of May 1, 2019, the FCC requires ALL the following information to be in the installation manual. Modular transmitter applicants should include information in their instructions for all these items indicating clearly when they are not applicable. For example information on trace antenna design could indicate Not Applicable. Also if a module is limited to only a grantees own products and not intended for sale to third parties, the user instructions may not need to be detailed and the following items can be placed in the operational description, but this should include a cover letter as cited above. 1. List of applicable FCC rules. KDB 996369 D03, Section 2.2 a. Only list rules related to the transmitter. 2. Summarize the specific operational use conditions. KDB 996369 D03, Section 2.3 a. Conditions such as limits on antennas, cable loss, reduction of power for point to point 3. Limited Module Procedures. KDB 996369 D03, Section 2.4 systems, professional installation info a. Describe alternative means that the grantee uses to verify the host meets the necessary limiting conditions b. When RF exposure evaluation is necessary, state how control will be maintained such that compliance is ensured, such as Class II for new hosts, etc. 4. Trace antenna designs. KDB 996369 D03, Section 2.5 a. Layout of trace design, parts list, antenna, connectors, isolation requirements, tests for design verification, and production test procedures for ensuring compliance. If confidential, the method used to keep confidential must be identified and information provided in the operational description. 5. RF exposure considerations. KDB 996369 D03, Section 2.6 a. Clearly and explicitly state conditions that allow host manufacturers to use the module. Two types of instructions are necessary: first to the host manufacturer to define conditions (mobile, portable xx cm from body) and second additional text needed to be provided to the end user in the host product manuals. 6. Antennas. KDB 996369 D03, Section 2.7 a. List of antennas included in the application and all applicable professional installer instructions when applicable. The antenna list shall also identify the antenna types

(monopole, PIFA, dipole, etc note that omni-directional is not considered a type) 7. Label and compliance information. KDB 996369 D03, Section 2.8 a. Advice to host integrators that they need to provide a physical or e-label stating Contains FCC ID: with their finished product a. 8. Information on test modes and additional testing requirements. KDB 996369 D03, Section 2.9 Test modes that should be taken into consideration by host integrators including clarifications necessary for stand-alone and simultaneous configurations. Provide information on how to configure test modes for evaluation 9. Additional testing, Part 15 Subpart B disclaimer. KDB 996369 D03, Section 2.10 b. Sincerely,

- All Items shown to the left are provided in the Modular Integration Guide (or UM) for Full Modular Approval

(MA) or LMA.

- An LMA applies and is approved ONLY for use by the grantee in their own products, and not intended for sale to 3rd parties as provided in a separate cover letter. Therefore the information shown to the left is found in the theory of operation. By:

/Vice President__ _Jay Moulton, RF Exposure Lab____

(Signature/Title1)

(Print name) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Date: 02/26/2020 Ref. FCC Class I| Permissive change for FCC ID: 2AFDI-ITCNFA324

(Original Grant date: 12/10/2015) Dear Examiner, This is to request a Class || permissive change for FCC ID: 2AFDI-ITCNFA324, originally granted on 12/10/2015. The major change filed under this application is:

Change #1: This change is to request approval for the portable use category, specific to host eSight Corporation's head mounted device:

Models: 300200x where x signifies the color of the case. The only difference between model numbers is the enclosure color. J Sincerely, , 7 By: G og Reznik Title: CFO (Signature) On behalf of: Intrinsyc Technologies Corp. Telephone: 604-801-6461 Fax: 604-801-6417 E-mail greznik@intrinsyc.com

American Certification Body Inc. 6731 Whittier Ave, Suite C110, McLean, VA 22101 USA Date: 02/10/2020 Ref: FCC Class II Permissive change for FCC ID: 2AFDI-ITCNFA324 and IC Class 4 Permissive change for IC: 9049A-ITCNFA324, model name: ITCNFA324.

(Original Grant date: 12/10/2015) Dear Examiner, This letter is to attest that we have verified the new power level settings of the module to not exceed the target limits of 13 dBm for 2.4GHz and 13 dBm for 5GHz WLAN for use with the host eSight Corporation head mounted display. Sincerely, By: George Reznik Title: CFO ature) On behalf of: Intrinsyc Technologies Corp. Telephone: 604-801-6461 Fax: 604-801-6417 e-mail: greznik@intrinsyc.com Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461