FCC ID: 2AFDI-ITCOQ835S Intrinsyc Open-Q 835 uSOM

Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide

[Document: ICS-01RND1265-TN-077 Revision: 1.1]

NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFORMATION INTRINSYC Technologies Corp. claims proprietary rights to the material disclosed hereon. This drawing and/or technical information is issued in confidence for engineering information only and may not be reproduced or used to manufacture anything shown or referred to hereon without direct written permission from INTRINSYC Technologies Corp. to the user. This drawing and/or technical information is the property of INTRINSYC Technologies Corp. and is loaned for mutual assistance, to be returned when its purpose has been served. Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 Identification Document Title Document Number Version Date Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide ICS-01RND1265-TN-077 1.1 September 19, 2019 History REVISION DATE DESCRIPTION 0.1 0.2 1.0 1.1 Sept 6, 2019 Original Document Sept 9, 2019 Incorporated changes after initial document review:

Changed references and name of document from Open-QTM 835uSOM to Open-QTM 835SOM. Sept 17, 2019 Corrected minor typos on and changed revision to 1.0. Sept 19, 2019 Removed TM Superscript in Model and filename All PAGES All All 9, 13 Note: The Intrinsyc Open-Q 835 SOM radio module (the Module) is certified for compliance for use in the USA and Canada only. For use in other countries, certificates of compliance must be obtained for that country or region before the module can be sold, operated or incorporated into products. In addition, any deviation from the settings, methods, conditions and restrictions for integration of the Module into a host system, as defined in this document, could be a violation of applicable national law and may be punishable as such, and in such event, the products into which the Module is incorporated may not be lawfully distributed or sold in such countries. Intrinsyc assumes no responsibility for any such liability or loss related to installation or operation of the Module. Copyright Intrinsyc Technologies Corporation 1 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 Table of Contents INTRODUCTION ................................................................................... 3 APPLICABLE MODULE ....................................................................... 3 ADDITIONAL REGULATORY CONFORMANCE TESTING AND/OR 1. 2. 3. SUBMISSIONS REQUIRED BY THE INTEGRATOR ..................................... 3 COMPLIANT/ALLOWABLE TX POWER SETTINGS .......................... 3 4. 5. ALLOWABLE ANTENNAS TO USE WITH THE RADIO MODULE ..... 4 ANTENNA PLACEMENT AND RF SAFETY ........................................ 5 6. 7. SIMULTANEOUS TRANSMISSION WITH OTHER INTEGRATED OR PLUG-IN RADIOS ........................................................................................... 6 MODULE MAY NOT BE INSTALLED BY END USERS ...................... 6 8. 9. REQUIRED LABELING ON THE OUTSIDE OF THE HOST ............... 6 9.1 FCC Labeling Requirements on the Outside of the Host .................................. 6 9.2 Industry Canada Labeling Requirements on the Outside of the Host ............... 7 10. REQUIRED LABELING ON THE MODULE ......................................... 8 10.1 FCC and Industry Canada Labelling on the Module ....................................... 8 11. REQUIRED REGULATORY WORDING FOR END USER MANUAL /

INSTALLATION MANUAL .............................................................................. 8 11.1 FCC Requirements for End User Manual / Installation Manual ..................... 8 FEDERAL COMMUNICATIONS INTERFERENCE STATEMENT .................. 8 FCC RF Exposure Requirements: ........................................................................... 9 11.2 Industry Canada Requirements for End User Manual / Installation Manual . 10 Industry Canada Statements .................................................................................. 10 Radiation Exposure Statement ............................................................................... 11 Dclaration d'exposition aux radiations ................................................................. 11 12. OEM INTEGRATOR CHECKLIST ...................................................... 13 Copyright Intrinsyc Technologies Corporation 2 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 1. INTRODUCTION This document describes the steps that the OEM integrator must follow when designing and manufacturing a system utilizing the Open-Q 835 SOM Transmitter Module. Failing to follow the instructions in this document may invalidate the FCC and IC (Industry Canada) certifications and authorizations of the Module for use in the U.S. and Canada. The Module certifications described in this document apply only to radio conformance for the Module. The OEM integrator is responsible for all system-level EMI/EMC and Product Safety testing and certifications that apply to the host system in the U.S. and other countries where the system will be marketed or sold. 2. APPLICABLE MODULE Model Open-Q 835 SOM 3. ADDITIONAL REGULATORY CONFORMANCE TESTING AND/OR USA/FCC 2AFDI-ITCOQ835S CANADA/IC 9049A-ITCOQ835S SUBMISSIONS REQUIRED BY THE INTEGRATOR The modular certifications apply to the radio conformance for the Module only. The OEM integrator is responsible for additional system-level EMI/EMC and Product Safety testing and certification that applies in the U.S. and other countries to the host system containing the Module. This includes but is not limited to Federal Communications Commission (FCC) Part 15 Class B Digital Emissions. These system-level EMC tests are to be done with the Module installed and included in the scope of the submission. Some of the countries for which modular certifications are provided require additional submissions, authorizations or import permission by the system-vendor or importer. The integrator is responsible for these additional actions. Modular radio certification is not possible in some countries. For such countries, OEM integrators must ensure radio certification for the end system is obtained, before placing the product on the market. 4. COMPLIANT/ALLOWABLE TX POWER SETTINGS Any adjustments made to increase transmit power settings will invalidate all radio certifications for this module. Copyright Intrinsyc Technologies Corporation 3 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 5. ALLOWABLE ANTENNAS TO USE WITH THE RADIO MODULE The module is certified for use with certain antennas as described in this section. Allowed Antenna Types:

1. Dipole antenna Table 1 Allowed Maximum Gain (dBi) Dipole, Including Cable Loss 3.32 6.11 2.4~2.5GHz 4.9~5.8GHz The required antenna impedance is 50 ohms. Use of other antenna types or the same type of antenna but with higher gain than listed above is not allowed without additional testing and appropriate FCC or IC approval. Use of a similar antenna may only require a C1PC to confirm the performance for SAR is the same or better (i.e. lower) but only an equivalent antenna can be used without any additional testing. Copyright Intrinsyc Technologies Corporation 4 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 6. ANTENNA PLACEMENT AND RF SAFETY The FCC and other countries regulatory bodies impose strict conditions and limitations on the RF exposure levels of end products. Acceptable RF exposure levels for this Module depend on transmit power, the location of the transmitting antenna(s) inside the host system and the expected separation of the transmitting antennas to the end user. OEM integrators must take great care to ensure each host system complies with the applicable RF exposure requirements. The antenna-to-user (bystander) separation distance must be greater than 20 cm. Failure to adhere to these separation/spacing rules will invalidate the FCC and IC certifications for the Module. This separation is measured between the closest point of each transmitting antenna inside the host device to the point of contact by the user or nearby person outside the host device. For notebooks/netbooks/laptops with antennas in display section, the LCD is opened 90 degrees/perpendicular to the keyboard. The separation distance is then measured from the nearest point of each transmitting antennas to the bottom of the host. Use in the keyboard section of a netbook or laptop or use in a tablet device or convertible tablet would require host-specific testing. For notebooks/netbooks/laptops, the transmitting antenna cables shall be positioned away from the antenna elements to conform to the configuration tested for compliance. When transmitting antennas are installed in the display section of notebook/netbook/laptops, the display section shall not have metallic components and material that can influence or change the operating and RF exposure characteristics of the antennas. The separation between the main and aux antennas must be at least 3 cm. The transmitter module may not be co-located with any other transmitter or antenna. SAR evaluation is required if the separation distance between the user or bystanders and the device is less than or equal to 20 cm. Where one or more of the conditions above cannot be met for a particular host system, additional testing is required to secure the necessary certifications for the system. Note: These restrictions do not apply to receive-only antenna. Copyright Intrinsyc Technologies Corporation 5 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 7. SIMULTANEOUS TRANSMISSION WITH OTHER INTEGRATED OR PLUG-IN RADIOS The FCC and IC impose conditions and limitations when additional radio(s) are co-located in the same host system as the Module with capability to transmit simultaneously. Co-

locating other radios such as an integrated or plug in Wireless WAN/cellular radio with the Module requires additional evaluation and possibly submission for authorization from the FCC and IC. Because the rules are highly dependent on the characteristics of the particular radios that are co-located and simultaneously transmitting, the OEM integrator should seek guidance from a knowledgeable test lab or consultant to determine if additional testing and certification is required. In this case, failure to evaluate and follow the required FCC and IC procedures will invalidate the FCC and IC certifications of the Module and end system. 8. MODULE MAY NOT BE INSTALLED BY END USERS FCC and IC rules require this Module to be installed in host systems at the factory by the OEM integrator. Thus, end users of the system may not install the Module. Therefore, the host product user instructions must not advise the end user on how to access or remove the Module. Additional FCC authorization/filing is needed to allow end user installation of the radio modules. If modules are provided to the end users for installation in the host, a two-way authentication protocol is required to limit the module to operate only with the authorized host system. 9. REQUIRED LABELING ON THE OUTSIDE OF THE HOST 9.1 FCC Labeling Requirements on the Outside of the Host The FCC requires a label on the outside of the host system visible to the end user. Example wording is:

Contains:

FCC ID: 2AFDI-ITCOQ835S IC: 9049A-ITCOQ835S Copyright Intrinsyc Technologies Corporation 6 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 The FCC requires a logo signifying emission compliance on the outside of the host system. The OEM integrator is responsible to perform FCC Part 15 Class B digital emissions testing on the end system with the radio Module installed. The FCC logo below should not be affixed unless the OEM integrator has obtained the necessary Part 15 approval, e.g., self-

declaration of conformity. If the host system is approved to FCC Class B digital emissions limits under a grant of certification issued by a TCB, the FCC ID number shown on the grant should be used on the label instead of the FCC logo below. Also see https://www.fcc.gov/logos. A certified modular has the option to use a permanently affixed label, or an electronic label

(Refer to FCC KDB 784748 D02 e labeling for e-labelling guidance). All modules without an integrated display on the module must be labelled with a modules FCC ID - Section 2.926. 9.2 Industry Canada Labeling Requirements on the Outside of the Host End Product Labeling The final end product must be labeled in a visible area with the following for the Open-Q 835 SOM: Contains IC: 9049A-ITCOQ835S. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:

Open-Q 835 SOM: Contient des IC: 9049A-ITCOQ835S. Copyright Intrinsyc Technologies Corporation 7 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 10. REQUIRED LABELING ON THE MODULE 10.1 FCC and Industry Canada Labelling on the Module The OEM integrator must ensure that the FCC ID and IC number is affixed on the Module or in a User/Installation Manual along with other country certification numbers and logos as described herein. Note: the original Module manufacturer may affix regulatory labeling at time of Module manufacturing. However, the OEM integrator must ensure that Module labeling is complete, correct, and applicable for all the countries to which the host system is to be imported, marketed, or sold. 11. REQUIRED REGULATORY WORDING FOR END USER MANUAL / INSTALLATION MANUAL 11.1 FCC Requirements for End User Manual / Installation Manual The OEM integrator must provide instructions in the end user manual how to retrieve the module FCC ID for host devices using electronic labeling (for example an integrated display) in lieu of a physical label or nameplate to meet the labelling requirements of Industry Canada (Refer to FCC KDB 784748 D02 e labeling document for guidance). The OEM integrator must include text in the end user manual meeting the regulators requirements. When the module is installed inside another device, the user manual of that device must contain the statements and warnings below (text in red font must be replaced):

FEDERAL COMMUNICATIONS INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate warranty and all applicable regulatory certification and approvals, including authority to operate this device. FCC Part 15 Digital Emissions Compliance We [System Manufacturer Name, Address, Telephone], declare under our sole responsibility that the product [System Name] complies with Part 15 Rules. Operation is Copyright Intrinsyc Technologies Corporation 8 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from the one the receiver Increase the separation between the equipment and receiver. is connected to. Consult the dealer or an experienced radio or TV technician for help.

(Notice for 5GHz and/or when co-located with 5GHz transmitters, the following statements should be provided for user information.) Operations in the 5.15-5.25GHz band are restricted to indoor usage only. (For 5GHz only) IMPORTANT! Changes or modifications not expressly approved by [System Manufacturer Name] could void the users authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC RF Exposure Requirements:

This product complies with the FCC RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. This device is only authorized for use in a mobile application, at least 20 cm of separation distance between the radiating antenna and the user's body must be maintained at all times. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the users body or set the device to a lower output power if such a function is available. Separate approval is required for all other operating configurations, including portable configurations with respect to 47 CFR Part 2.1093 and different antenna configurations. Copyright Intrinsyc Technologies Corporation 9 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 11.2 Industry Canada Requirements for End User Manual / Installation Manual Industry Canada Statements This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) lappareil ne doit pas produire de brouillage;

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

(Notice for 5GHz and/or when co-located with 5GHz transmitters, the following statements should be provided for user information.) Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii)the maximum antenna gain permitted for devices in the bands 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices Avertissement:

Le guide d'utilisation des dispositifs pour rseau-x locaux doit Inclure des instructions pccises su:r les restrictions susmentionnes, notamment:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5150-5250 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e.;

(iii)le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 57255825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour l'exploitation point point et non point point, selon le cas. Copyright Intrinsyc Technologies Corporation 10 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement This equipment complies with radiation exposure limits set forth for uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Dclaration d'exposition aux radiations Cet appareil se conforme aux limites d'exposition aux rayonnements pour un environnement non contrl. L'antenne (s) qui est utilis pour cet metteur doit tre install pour produire une distance de sparation d'au moins 20 cm de toutes personnes et ne doit pas tre install proximit ou utilis en conjonction avec une autre antenne ou metteur. This device is intended only for OEM integrators under the following conditions:

1. The antenna used will be of the same type and have an antenna gain which is the same or less than what is listed in this document. 2. The antenna must be installed such that 20 cm is maintained between the antenna and users. 3. The transmitter module may not be co-located with any other transmitter or antenna. As long as the conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing the end product and any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:

1. L'antenne utilise sera du mme type et aura un gain d'antenne identique ou infrieur ce qui est indiqu dans ce document. 2. L'antenne doit tre install de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs. 3. Le module metteur peut ne pas tre co-localis avec un autre metteur ou antenne. Tant que les conditions ci-dessus sont remplies, d'autres tests d'mission ne seront pas ncessaires. Cependant, l'intgrateur OEM est toujours responsable pour tester le produit final et toutes les exigences de conformit supplmentaires ncessaires avec ce module install. Important Note:

In the event that these conditions cannot be met, then the Canadian authorization is no longer considered valid and the IC ID cannot be used on the final product. In these Copyright Intrinsyc Technologies Corporation 11 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization. Note Importante:

Dans le cas o ces conditions ne peuvent tre satisfaites, l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in this manual. The OEM integrator must provide instructions in the end user manual how to retrieve the module IC number for host devices using electronic labeling (for example an integrated display) in lieu of a physical label or nameplate to meet the labelling requirements of Industry Canada (Refer to IC Notice 2014-DRS1003 for guidance). Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. L'intgrateur OEM doit fournir des instructions dans le manuel utilisateur expliquant comment rcuprer le numro IC du module pour les appareils htes en utilisant l'tiquetage lectronique (par exemple un cran intgr) en lieu et place d'une tiquette physique ou plaque signaltique pour rpondre aux exigences en matire d'tiquetage d'Industrie Canada

(Se reporter la note d'IC 2014 - DRS1003 pour plus d'information). Copyright Intrinsyc Technologies Corporation 12 Open-Q 835 SOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 12. OEM INTEGRATOR CHECKLIST The OEM Integrator will integrate the Module in the host systems in accordance with the instruction specified in this document and the documents referenced herein. The OEM Integrator will ensure the Module is integrated in a host system using only antennas that are of the same type and having equal or less antenna gain as described in this document. The OEM Integrator will ensure the antenna placement inside the host system will maintain the required spacing to the end user for RF Exposure compliance, as specified in this document. If other radios are integrated inside the host with the Module, the OEM Integrator will contact a test lab or TCB to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. The OEM Integrator will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself is labeled as specified in this document. The OEM Integrator will ensure that nothing is done that will change the transmit power level of the module. The OEM Integrator will ensure end user documentation will contain clear instructions on how to access the FCC ID and IC Number of the module should an electronic display (e-labeling) be used to meet the FCC and IC labeling requirements

(Refer to FCC KDB 784748 D02 e labeling document and IC Notice 2014-DRS1003 for guidance). The OEM Integrator will ensure end user documentation will contain clear instructions on how to access the FCC ID and IC Number of the module should an electronic display (e-labeling) be used to meet the FCC and IC labeling requirements

(Refer to FCC KDB 784748 D02 e labeling document and IC Notice 2014-DRS1003 for guidance). The Open-Q 835 SOM is a pre-certified Wi-Fi/BT module that requires a specific binary Board Data File (BDF) and WLAN configuration file to maintain compliance. The correct BDF and WLAN configuration files are included with Android software releases from Intrinsyc (as indicated in software release notes). Customers programming the SOM with other OS images must contact Intrinsyc to ensure they have incorporated the correct files to maintain compliance. Copyright Intrinsyc Technologies Corporation 13

Model: Open-Q 835 SOM FCC ID: 2AFDI-ITCOQ835S IC: 9049A-ITCOQ835S Internal Photos Top Side with RF Shield Covers Removed Bottom Side Top Board Edge Bottom Board Edge Left Board Edge Right Board Edge

Model: Open-Q 835 SOM FCC ID: 2AFDI-ITCOQ835S IC: 9049A-ITCOQ835S External Photos Top Side with RF Shield Bottom Side Top Board Edge Bottom Board Edge Left Board Edge Right Board Edge Reference No.: 190410E09 Report No.: {report no}

Page No. 1 / 2 Reference No.: 190410E09 Report No.: {report no}

Page No. 2 / 2

Model: Open-Q 835 SOM FCC ID: 2AFDI-ITCOQ835S IC: 9049A-ITCOQ835S Transmitter Module FCC and IC Label Location Top Side Drawing of Module with Label Dimension (mm).

Date: 2019-09-30 FCC ID:2AFDI-ITCOQ835S AUTHORIZATION LETTER To Whom It May Concern:

Intrinsyc Technologies Corporation hereby authorizes Debby Lin / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Debby Lin / Senior Specialist of BV CPS Taoyuan on Intrinsyc Technologies Corporations behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

George Reznik / CFO Intrinsyc Technologies Corporation Tel: (604) 801-6461 Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461

Date: 2019-09-30 FCC ID:2AFDI-ITCOQ835S To the attention of Federal Communications Commission Authorization and Evaluation Division Schematics Block Diagram Operational Description Software Operational Description Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

George Reznik / CFO Intrinsyc Technologies Corporation Tel: (604) 801-6461 Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461

FCC ID: 2AFDI-ITCOQ835S Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch October 16, 2019 Dear Application Examiner, Intrinsyc Technologies Corporation., Intrinsyc Open-Q 835 SOM, FCC ID:

2AFDI-ITCOQ835S would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. The modular transmitter must have its own RF shielding. The radio portion of this module has been shielded, please see exhibition External Photo. 2. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs, it is integrated in chip Open-Q 835 SOM. 3. The modular transmitter must have its own power supply regulation. The part number of this regulator is Open-Q 835 SOM. 4. The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C). The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. The modular transmitter must be labeled with its own FCC ID number. Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. Report No.: RF190610E05, RF190610E05-1, RF190610E05-2, RF190610E05-3, RF190610E05-4, RF190610E05-5, SA190610E05 FCC ID: 2AFDI-ITCOQ835S 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Debby Lin Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch Report No.: RF190610E05, RF190610E05-1, RF190610E05-2, RF190610E05-3, RF190610E05-4, RF190610E05-5, SA190610E05

DFS client device channel plan and software operational declaration Date: 2019-09-30 We, Intrinsyc Technologies Corporation, declare that the device, FCC ID:2AFDI-ITCOQ835S Model Name: Open-Q 835 SOM, does not have Ad Hoc on non-US frequencies and/or on DFS frequencies. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Below is the channel / frequency plan for the device 5 CH 2 3 Frequency (MHz) 2412 1 11 2462 Active Active Active Active Active Active Active Active Active Active Active 10 2457 2427 2432 2452 2417 2422 2437 2442 2447 4 6 7 8 9 Scan Type 5G band 1 CH 36 Frequency (MHz) 5180 48 5240 Active Active Active Active Active Active Active 42 5210 44 5220 38 5190 40 5200 46 5230 Scan Type 5G band 2 CH 52 Frequency (MHz) 5260 54 5270 56 5280 58 5290 60 5300 62 5310 64 5320 Passive Passive Passive Passive Passive Passive Passive Scan Type 5G band 3 CH 100 Frequency (MHz) 5500 122 5610 Passive Passive Passive Passive Passive Passive Passive Passive Passive Passive Passive 102 5510 106 5530 108 5540 118 5590 104 5520 110 5550 112 5560 116 5580 120 5600 Scan Type CH 124 Frequency (MHz) 5620 126 5630 128 5640 132 5660 134 5670 136 5680 138 5690 140 5700 142 5710 144 5720 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive Passive Passive 5G band 4 CH 149 Frequency (MHz) 5745 165 5825 Active Active Active Active Active Active Active Active 155 5775 157 5785 151 5755 153 5765 159 5795 161 5805 Scan Type Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461 Also, on DFS channels, the WLAN driver in the device operates under the control of an AP at all times, except when in ad-hoc mode on US non-DFS channels. The device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Only authorized firmware updates are provided by Intrinsyc to our customers. Sincerely yours,

George Reznik / CFO Intrinsyc Technologies Corporation Tel: (604) 801-6461 Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461

Date: September 30, 2019 We, Intrinsyc Technologies Corporation declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID:2AFDI-ITCOQ835S If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

George Reznik / CFO Intrinsyc Technologies Corporation Tel: (604) 801-6461 Intrinsyc Technologies Corporation Suite 300-885 Dunsmuir Street Vancouver, BC, Canada V6C 1N5

+1-604-801-6461