FCC ID: 2AFR8F1703A Custom S-Pen Tray with Recoiler, Custom Crown S-Pen Vertical Recoiler

1 Clean the fixture with the provided alcohol wipe. Let it dry completely. 2 Optional:

If desired, route the cable through a hole or slot in the fixture. 3 Peel the liners from the adhesives on the bottom of the recoiler. Series 2800 Custom S-Pen Charger Vertical Recoiler DNAZ72 4 Place the recoiler in the desired location and apply pressure for at 10 least seconds. 5 Pull the sylus clip from the recoiler. 6 Remove the pin cover from the fob tool. 7a Insert the pin into the hole opposite of the cable. 7b Pivot the fob tool back to remove the retainer. 8 Remove the sleeve and separate the upper and lower halves of the stylus clip. 9a Prepare the stylus for installation into the clip by making sure that it is clicked open. 9b With the S-Pen clicked open, place it into the cavity of the bottom clam shell piece. The button on the S-Pen should face upwards. 10 Place the top half of the clam shell over the S-Pen. 11 Orient the sleeve cover so that the gap will align with the cable. Slide the sleeve up the length of the S-Pen and over the the 2 pieces of the stylus clip. 12 Insert the retainer into the hole on the outer sleeve and through the bottom piece of the clip. It should sit flush when properly assembled. 13 Insert the S-Pen into the hole in the top of the recoiler to display. Cable Gap 14 Power Only: Plug the supplied USB-

C cable into the side of the power injection port. 15 Plug the USB-A end of the power cable into a power supply (InVues PS515 or an OEM travel adapter). Plug the power supply into a power outlet. 16 Optional: If Alarming fuctionality is desired, plug the micro-USB end of the cable into a preinstalled S2800, S2865 or Zips 2.0 unit. 17 If the micro-USB end of the cable was plugged in to provide alarming function, the LED on the sensor will be illuminated to indicate that the alarm circuit is armed. 18 The LED on the recoiler will illuminate to indicate the S-Pen is charging when fully docked as shown and will turn off when it is removed. FCC WARNING STATEMENT FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC RADIATION EXPOSURE STATEMENT

(Wireless Charger Dock) This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. IC WARNING STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage, et (2) Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC RADIATION EXPOSURE STATEMENT

(Wireless Charger Dock) This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet quipement est conforme aux limites tablies par Industrie Canada en matire dexposition aux radiofrquences dans un environnement non contrl. Cet appareil etson antenne ne doivent pas tre colocaliss ou fonctionner en conjonction avec tout autre antenne ou metteur. Cet quipement doit tre install et utilis avec une distance minimale de 20cm entre le radiateur et votre corps. SD0612 Rev5 07/11a/18 www.invue.com NA / LATAM // 704.752.6513 888.55.INVUE EMEA // +31.23.8900150 APAC // +852.3127.6811 2018 InVue Security Products Inc. All rights reserved. InVue is a registered trademark of InVue Security Products.

F1703A (Horizontal Stylus Holder) Internal Photo Plastic Removed and View from Top PCBA Top View and Antenna Taken out from Plastic PCBA Bottom View Taken out from Plastic F1703A (Vertical Stylus Holder) Internal Photo Plastic Removed and View from Top Antenna Pictures Top Side Bottom Side PCBA Top View and Antenna Taken out from Plastic PCBA Bottom View Taken out from Plastic F1703A PCBA pictures without shield Top Side Bottom Side

F1703A (Horizontal Stylus Holder) External Photo Top Bottom Front Back Side1 Side2 F1703A (Vertical Stylus Holder) External Photo Top Bottom Front Back Side1 Side2 Model # / HVIN Label Location of DNAX950 Custom S-Pen Tray Recoiler Label Location of DNAZ72 PMN: Custom Crown S-Pen Vertical Recoiler Label Location of DNAZ81 PMN: Custom Crown S-Pen Vertical Recoiler

A SHEET 1 OF 1 DRAWING NO. REV F1703034 2 B C D E F G H I J K L REVISIONS REV 0 1 2 DESCRIPTION RELEASED CHECKED DATE Initial release ECR 180402084814 Updated FCC ID, Added IC number Updated description DCS MSK JAH 03JUL2018 12Jul2018 1 12Jul2018 AO AO 0.50 TYP 1 20.00 white border Font: Helvetica LT Text Height: 1.5mm Text Color: White black background SCALE 1:1

(FOR REFERENCE ONLY) F1703034-01 white border Font: Helvetica LT Text Height: 1.5mm Text Color: White SCALE 1:1

(FOR REFERENCE ONLY) black background F1703034-02 2 10.00 0.50 TYP 2 10.00 F1703034-01 1 20.00 F1703034-02 Notes:

1. Material: 0.06mm Mylar & 0.06 clear layer with adhesive backing A B C D E F G H I InVue Security Products 9201 Baybrook Lane Charlotte, NC 28277 Phone: (704) 752-6513 PROPRIETARY AND CONFIDENTIAL THIS DRAWING IS PROPERTY OF INVUE SECURITY PRODUCTS, INC. AND IS LOANED UPON CONDITION THAT IT IS NOT TO BE REPRODUCED OR COPIED IN WHOLE OR IN PART, OR USED FOR FURNISHING INFORMATION TO OTHERS, OR FOR ANY OTHER PURPOSE DETRIMENTAL TO THE INTEREST OF INVUE SECURITY PRODUCTS, INC. AND WILL BE RETURNED UPON REQUEST. TITLE FCC Label Pisces Crown PROJECT NO. F1703 MASS (GRAMS) UNITS MM 0.0 ENGINEER DRAWING NO. DS SHEET 1 OF 1 K L F1703034 TOLERANCE TABLE (MM) UNLESS OTHERWISE SPECIFIED DIMENSION TOLERANCE L 5 5 < L 20 20 < L 65 65 < L 150 150 < L ANGLES 0.10 0.15 0.25 0.35 0.50 2 J 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

Long Term Confidentiality Request Letter 07/13/18 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Custom S-Pen Tray with Recoiler, Custom Crown S-Pen Vertical Recoiler, MODEL #: DNAX950B, DNAX950W, DNAX950Z, DNAZ72B, DNAZ72W, DNAZ72Z, DNAZ81W, and DNAZ81Z AND FCC ID#: 2AFR8F1703A To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the schematic, layout, component datasheets, and antenna information to be submitted with this application be permanently withheld from public review. Parts of these items are proprietary to our customer. We required to keep this information confidential. Please contact me if there is any information you may need. Sincerely, Signature:

Date: 07/13/18 Signed by (printed name): Yasushi Tamura

Model Difference Letter 11/02/18 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 To Whom It May Concern:

This letter serves as description and difference of each model. All the model are using the same PCB and the same components are used to populate for the charger circuits. Following are list of difference for PCBA population. LED population: Blue LED and current limit resistor (schematic designation, see theory of operation for more info) R1 and D2 are not populated for DNAX950x and R4 and D3 are not populated for DNAZ72x and DNAZ81Z. Sense circuit: security sense circuit resistor (schematic designation) R6 is populated different value for security

(DNAX950x and DNAZ72x) and non-security version (DNAZ81W). Power Connection differences: DNAX950x and DNAZ72x use USB Type-C receptacle for power supply connection and DNAZ81x uses USB Type-A plug for power supply connection. Table below shows product description of each model. Model DNAX950B DNAX950W DNAX950Z DNAZ72B DNAZ72W DNAZ72Z DNAZ81W DNAZ81Z Description Tray version of stylus charger. The stylus will lay horizontal during the charge. PCB will be inserted horizontally inside of a black plastic. Tray version of stylus charger. The stylus will lay horizontal during the charge. PCB will be inserted horizontally inside of a white plastic. Tray version of stylus charger. The stylus will lay horizontal during the charge. PCB will be inserted horizontally inside of a white plastic with black inlay. Vertical version of stylus charger. The stylus will stand vertically during the charge. PCB will be inserted vertically inside of a black plastic. Vertical version of stylus charger. The stylus will stand vertically during the charge. PCB will be inserted vertically inside of a white plastic. Vertical version of stylus charger. The stylus will stand vertically during the charge. PCB will be inserted vertically inside of a white plastic with black inlay. Larger vertical version of stylus charger (plastic dimension is larger than DNAZ72x). The stylus will stand vertically during the charge. PCB will be inserted vertically inside of a white plastic. Larger vertical version of stylus charger (plastic dimension is larger than DNAZ72x). The stylus will stand vertically during the charge. PCB will be inserted vertically inside of a white plastic with black inlay. Please contact me if there is any information you may need. Sincerely, Signature:

Date: 11/02/18 Signed by (printed name): Yasushi Tamura

Short Term Confidentiality Request Letter 07/03/18 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Short Term Confidentiality Request For EUT NAME/MODEL #: Custom S-Pen Tray with Recoiler, Custom Crown S-Pen Vertical Recoiler, FCC ID#: 2AFR8F1703A To Whom It May Concern:

In accordance with sections 0.457 and 0.459 of CFR 47, InVue. requests short-term Confidentiality of following sections of this application for a period of 45 days after grant is issued. Test setup photos External photos Internal photos Users manual These documents contain detailed system and equipment descriptions and related information about the product, which InVue considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, InVue feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely,