5800RPS Wireless Roller Plunger Switch Figure 3, Battery Replacement LN CAUTION: Before drilling any holes, make sure that successfull GaNo Go transmission reception tests have been conducted, LN CAUTION: BATTERY CAUTION: Risk of fire, exposion and burns, Go not recharge, disassemble, heat above 212 F (100 C) or incinerate, Dispose of used batteries promptly. Keap away from children. MOUNTING
. Mark the selected location for the transmitter on the hinge side of the door frame at least 4 above the floor. Bh
. Before drilling any holes, make sure that the successful Go/No Ga transmission tests have been conducted. ha
. Drill hale at the location marked for the transmitter (3/4" diameter, at least 1-1/4 in depth). Power Source) 3,0 Lit!
Temperature Range Figure 2, SPECIFICATIONS Ee tee OowelPackage | 0.750" diameter Additional Info | Dowel Lid 0.850" diameter x 0,060" thick Dimensions:
Wire Antenna | 8" x 1/8" flexible antenna extends from sensor Fits Cavity Depth) 1.00" depth y ium Coin Cell Battery CR1620 1? te 120 F (-12 to 49 C) 4. Drill a sacond hole (1/4" in diameter, at least 8" in dapth) at the center of the first hole for antenna insertion or insert the antenna inte the space between the door frame and the stud framing. in
. Insert the antenna into the provided straw. This is to make the installation easy and ensure the antenna will remain straight, Never color bunch up the Compatibility Doors Woodand MetalFrame Note; Range may be reduced if used in metal frame doors, antenna, 6, Insert the transmitter and antenna assembly into the hole so that the transmitter flange is flush with the surface of the door frame, DO NOT hammer the transmitter into place with hard blows, Press into place either by hand or simply by closing the door, which presses it into place,
=J
. secure the transmitter by installing the two screws provided, Ths device complies wih FOC part 15 and Indusiy Canada trense-axempl ASS Standards) Operation is Subject to the fobowing leo condiliors:
1. This device may not cause harmful imerference, 2. This device must accept any interference that may be received, including interference that may Cause undesired operation The user shall not make any changes or modifications to the equipment unless authonzed by the Installation Instructions OF User Manual. Unauthorized changes of modifications could void the user's authority to operate the equipment.
J STEP 2 TO THE INSTALLER Reguier maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital te the continuous satisfactory operation of any alarm system, The installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper Operation and [imitations of the alarm system ard its component parts. Recommendations must be inchided for a spetife: program of frequent testing (at least weekly) to insure the system's operation at all times. REFER TO THE [INSTALLATION INSTRUCTIONS FOR THE RECEIVER | CONTROL WITH WHICH THIS DEVICE IS USED FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM, FOR WARRANTY INFORMATION, PLEASE GO TO:
www. boneywellcomsecurity/hsc/resourneswa BATTERY INSTALLATION & REPLACEMENT 1, Remove the transmitter from the door frame by removing the two screws from the flange and prying the unit from the hole using the flat blade of a small screwdriver, The transmitter must be removed from the door comoaletely in order to refit the unit back inte the hole onee the internal battery has been replaced, he
. Using the flat blacie of a small screwdriver separate the transmitter assembly from the base with a slight counter-chockwise twist, Once open, slide the cap with the transmitter PC board assembly apart from the base, Pull the antenna through the hole in the base just enough to allow the battery to be replaced. Do net pull the antenna completely out of the base, ea Carefully remove the old battery from its battery holder on the bottom of the PC board. U.S. Patent No. 6,737,969 U5, Patent No, 7,081.816 STEP 3&4 STEP 5 & 6 4, Observe correct polarity (see Figure 3 Step 3.44) and insert the fresh battery inte the battery holder (positive polarity is shown on the battery holder). Aways use Energizer or Panasonic brand batteries, 5. Slide the transmitter assembly back into its base by gently pulling on the antenna, easing the assembly into place, 6 Snap the cap back onto the base, locking it into place, 7. Placing the antenna into the cavity first. reinsert the unit into its original eee hole in the door frame and secure the flange using the two screws Prewious iy removed, Honeywell 2 Corporate Centar Drive, Suite 100 P.O, Box 9040, Melville, NY 11747 Capyright 2070 Herepwell Inemational lnc. S00-07873 10/10 Rew A