Getting Started IoTargetingTM IoTargeting is a unique wireless target system, with an iOS and Android app. The app offers various gaming/scenario modes making it unique and interactive. Lets get started. Whats in the Box?
1. Master/Smart Target 2. Getting Started Guide 3. Light Cover Getting to Know Your Target There are two types of Targets available:
Master Target (MT) - Connects to Smart Target via app to set up various game modes and to 5 the cloud via Wi-Fi router Smart Target (ST) - Connects to Master Target only via app 1 2 3 5 5 5 4 1. ON-OFF Slider Switch 2. Target Type LED 3. Target Area 4. Battery Compartment 5. Standard Camera Thread Mounts ON-OFF Slider Switch Slide the switch in an upward direction to turn on the target and slide down to turn off. Target Type LED When target turns on, the LED is used to identify the target type. The following table indicates the target type based on the LED colour. Target MT ST LED Color Red Green Note: On the Master Target, the Type LED blinks until it has established a connection with your Wi-
Fi router. Target Area Target area consist of LEDs which blink or remains steady in various stages such as registering in the app, connecting with Wi-Fi router, Cloud, and Smart Targets. Use the table below to determine current status of your target. Target Area LED Color Target Type LED Color MT Blue Blinking Green Blinking ST Description Indicates target is turned on and waiting for direction from the app via Wi-Fi router Indicates target has registered in the app and waiting for cloud connection Indicates the battery is low Yellow Off/Type LED on Indicates target has connected to cloud Blue Blinking Indicates target is just turned on and waiting to get registered in the app via MT Indicates target is in registration process in the app via MT Indicates the battery is low Green Blinking Yellow Off/Type LED on Indicates target has registered Battery Compartment The battery compartment is used to provide power to the target using 4 x AA batteries. Note: Batteries are not included in the package. Mounting Points Target contains three mounting points, one on the back side and one on each side, for mounting via standard camera mounts. iOS and Android App IoTargeting requires an iOS or Android app which can be downloaded and installed from the Google Play or the App Store. Setup the Target 1. Remove the battery pack from the back of the target 2. Remove the cover, install 4 x AA batteries and insert the cover Press and Pull 3. Insert the battery pack into the target. Turn on the target by sliding On/Off switch in an upward direction Slide Up 4. Target area will start blinking along with the target type LED until successful registration with the app Target Area Target Type LED 5. Download and open the IoTargeting app on your smart phone or tablet. It will display the login page where first time users will need to create an account. Tap Sign Up to create an account. Once an account has been created, login to continue using the app 6. After logging in, the app will display the user profile page where you can register your new targets, update your profile, play games and do much more 7. Tap on Targets, then tap on ADD MT, follow setup prompts on the app to register your targets 8. Place targets in a safe location for game play Support For any queries or support, contact us at www.iotargeting.com. 2017 IoTargeting Inc. All rights reserved. FCC statement This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions:
1. This device may not cause harmful interference and 2. This device must accept any interference that is received, including any interfer ence that may cause undesired operation. This devic e is acting as a master device itself and operating in the 2.4 GHz
(2412 ~2462 MHz) band. Ad Hoc function is supported but not able to operate on non-US frequencies. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The min separation distance is 20cm. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre lefonctionnement. Radio Frequency Exposure Statement for IC The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The min separation distance is 20cm.