FCC ID: 2BCD8-ZK8201 RFID Read/Write Module

ZK8201V1.0 ZK8201 RFID Read/Write Module Specification The ZK8201 module is a single-channel UHF RFID module, developed by Iotelligent based on its own iBAT2000 chip. The module is specially designed to meet the needs of high-end RFID desktop label printers. The ZK8201 module provides one SMA antenna interface and 30dBm RF power output. While maintaining high cost efficiency, this module achieves high integration, low power consumption, excellent performance, stability and reliability, and has excellent Anti-jamming ability. It is the preferred choice for high performance/cost-effective UHF RFID desktop equipment. Operation instructions The module must be stably fixed to the structure of the main machine and ensure good grounding;

Before turning on the power, please carefully check whether the antenna port has been connected to the load;

Antenna standing wave is recommended to be better than 2.0. 2023-8-25 ZK8201V1.0 Key technical parameters Module specification Air interface protocol EPC C1G2ISO18000-6CGB/T29768-2013 Antenna interface One SMA antenna interface (female) Output power 0 ~ 30dBm, accuracy +/-1dB Operating frequency FCC Band: 902 ~ 928 MHz China Band II: 840 ~ 845 MHz Connector 8-pin connector Communication interface 3.3V TTL UART (115200 bps) Dimensions 62mm * 40mm * 12mm DC power supply DC voltage 5V Power saving mode Sleep mode 0.7W Power consumption 570mA@20dBm ESD protection Shock-proof 1500V Installation meets IEC requirements Working temperature

-20

~ +60 Module interface definition Interface pin 1 2 3 4 5 6 7 8 Definition SWDIO SWCLK UART0_RX UART0_TX UART1_RX UART1_TX VCC GND Functional description SWD Data SWD Clock Serial port 0 input Serial port 0 output Serial port 1 input Serial port 1 output Power supply, +5V Grounding IC IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device 2023-8-25 ZK8201V1.0 Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS)d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :

(1) Cet appareil ne doit pas causer d'interfrences.

(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. avertissements radio pour les appareils mobiles :

L' quipement est conforme aux limites d'exposition aux rayonnements dfinies par la IC pour les environnements non contrls. La distance minimale entre le dissipateur de chaleur et votre corps doit tre de 50 cm lors de l installation et de l utilisation du matriel. The distance between user and products should be no less than 50cm FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249 Integral antenna with antenna gain -24.67dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2BCD8-ZK8201 Or Contains FCC ID: 2BCD8-ZK8201 When the module is installed inside another device, the user manual of the host must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 &

15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirementthen the host can be sold legally. 2023-8-25 1.Basic information 1.1 POSTEK Technology Development Co., Ltd. Address: Floor 18, Block 2, Building B, Wisdom Plaza, No. 4068, Qiaoxiang Road, Nanshan District, Shenzhen, China 1.2 Test Principle 1 QP030-O13 1.1 Test equipment Name Model E5071B E5071C 3*3*2.5 Network Analyzer Network Analyzer 16 probes microwave chamber 1.2 Test enviroment Ambient temperat ure Relative humidity Atmospher presure Device ID RFI-LAB-

012 RFI-LAB-

032 RFI-LAB-

010 Manufa ctures Agilen t Agilen t Sunyie ld Calibrat ion Date 2019.10.2 3 2019.10.2 3 2019.03.1 5 Next Cal date 2020.10.22 2020.10.22 2021.03.14 23.2 61%RH 101.10k Pa 2 QP030-O13 2.Sample information 2.1 Sample information Product name Sample model Standard size Factory serial number Test items Frequency range Received date Test date Remark UHF PCB Antenna POSTEK_A1 Antenna size10.5mm*130mmLine length625mm

VSWR; radiation pattern; antenna gain; efficiency; pattern circularity 800-960MHz 12/31/2019 01/02/2020

3 QP030-O13 2.2 Sample physical picture 2.3 Placement of actual samples 4 QP030-O13 3.Test results 3.1 Test basis Object name Mobile communicati on antenna Paramet er name VSWR Radiatio n pattern Antenna gain Efficien cy Pattern circularity Efficien cy Antenna 3.2 Test uncertainty Method name Standard number GB/T 9410-2008 General Technical Specifications for Mobile Communication Antennas IEEE Antenna test standard procedure ANSI/IEEE Std 149-1979 The calculation of uncertainty is based on the "Guide to the Expression of Uncertainty in Measurement" (GUM) issued by ISO, and the expanded uncertainty is represented by a coverage factor of K=2 and a 95% confidence level. Project VSWR Gain Efficiency Uncertainty 0.3 1dB 10%

5 QP030-O13 3.3 Test data 3.3.1 Antenna network analyzer test 3.3.2 S11 Parameter data Frequency/MHz VSWR 800 1.07 74 850 1.08 75 900 1.07 09 960 1.04 22 6 QP030-O13 3.3.3 Antenna gain and efficiency Frequency/

MHz 800 81 0 820 830 Max gain/

dBi Efficiency

22. 57 0.1 8

22. 93 0. 16

23. 41 0.1 4

23. 50 0.1 3 84 0

23. 77 0. 14 850 860

23. 96 0.1 1

24. 18 0.1 0 87 0

24. 18 0. 10 880 890

24. 42 0.0 9

24. 64 0.0 9 90 0

24. 67 0. 09 910 920 930 940 950 960

24. 88 0.0 9

25. 02 0.0 9

24. 92 0.0 9

24. 80 0.0 9

24. 79 0.0 9

24. 68 0.0 9 7 QP030-O13 3.3.4 Pattern circularity Phi=90 81 0 10. 43 82 0 09. 19 83 0 08. 86 84 0 08. 47 85 0 08. 92 86 0 10. 46 87 0 10. 76 88 0 10. 20 89 0 09. 30 90 0 11. 26 91 0 14. 40 92 0 14. 44 93 0 12. 56 94 0 10. 95 95 0 9 6 0 12. 56 18. 22 Freq

/MHz Out of round ness/

dB 8 0 0 1 2

. 1 7 3.3.5 Radiation pattern

(1) X-Z Plane

(2) Y-Z Plane 8 QP030-O13

(3) X-Y Plane

(4) 3D pattern at 880MHz

-------------------------------------------------End------------------------------------------------

The following entent is blank 9 QP030-O13

RFID ReadMrite Module Model: ZK8201 Input: 5V ===570mA FCC ID: 2BCD8-ZK8201 SN: 2023040988 Ces Manufacturer : lotelligent Co., Ltd. Address: Room 2006, NO.1199 Defu Road, Jiading, Shanghai, China Importer : XXXXXX Address: XXXXXX Made In China vesoroezor NS @

ize 1970

DATE:2023/8/17 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, | appoint_BlueAsia of Technical Services(Shenzhen) Co.,Ltd And Building C, No. 107, Shihuan Road, Shiyan Sub-District, Baoan District, Shenzhen, Guangdong Province, China__ (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with lotelligent Co., Ltd. And Room 2006, NO.1199 Defu Road, Jiading, Shanghai, China (Applicant Name and address)

<Signature> Lory Aun Name: Long Xu Title: Quality Manager Company: lotelligent Co., Ltd.

DATE2023/8/17 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BCD8-ZK8201 Product Name: RFID Read/Write Module Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...) e Schematics e Block diagram e Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature> Lony; Wy Name: Long XU Title: Quality Manager Company: lotelligent Co., Ltd.

Covered Equipment Certification Letter Attestation 8/17/2023 Communications Federal Authorization and Evaluation 7435 Oakland Mills Road Columbia, USA MD 21046 Commission Division ATTN.: Reviewing Engineer FCC ID: 2BCD8-ZK8201 Co., Ltd. ("the applicant") Iotelligent is sought is not "covered"

to section authorization certifies prohibited 2.903 of the FCC rules. that the equipment from receiving equipment pursuant an equipment for which authorization Note: If the equipment any of the entities include for which the applicant on the current on why the equipment an explanation identified Covered seeks authorization by is produced should List, the applicant is not "covered"

equipment. Iotelligent application,

"covered"

equipment. Co., Ltd. ("the applicant") certifies of the that, as of the date of the filing the applicant is not identified on the Covered List as an entity producing Signed:

Printed Title:

Company Name: Iotelligent Co., Ltd. Date:2023/8/17 name: Long Xu Manager

Single Modular approval Declaration letter Co., Ltd .. app lies single modular approval for We, lotelligent Product Model:

Name: RFID Read/Write ZK8201 Module FCC ID: 2BCD8-ZK8201 According to 996369 DOl Module Equip Auth Guide v0lr04 and 15.212 requirement. and tuning capacitor(s) must have the radio frequency may be located ccuitry shielded. external to the shield, but must be Physical 1) The radio elements components on the module assembly;

Answer: Yes 2)The module must have buffered willcomply Answer:

inputs. Yes; All inputs to the modules inputs modulation/data to ensure with any type of input signal, are buffered through with Part 15 requirements that the device logic or microprocessor 3)The modular Answer:

transmitter Yes; A low drop out regulator must have its own power supply regulation

;s used for modular power supply regulation. a permanently attached 4)The module must contain antennaconnector, Sections15.203, 15.204(b), Yes; Device Answer:

and be marketed 15.204(c), and operated 2.929(b), 15.2120 is equipped with PCB antenna antenna, only with specific or contain a unique per antenna(s),

(5)The module must demonstrate modular Answer:

setup photo. Yes, distance between compliance in a stand-alone configuration, and all AEv are bigger tn10cm, rfer to affixed about labeling display (See KDB Publication 784748 label, with its permanently

(6) The module must be labeled electronic The modular Answer: Yes:

listed in the User Manual;

the module'Contains has a permanent.fixed The host device FCC ID:2BCD8-ZK8201 must be labeled

FCC ID label, or use an requiremen ts);

to display the FCCJD of and below statement was all the conditions Yes; The module comply

(7)The module must comply with all specific rules applicable including Answer:

includi Refer to test report in the integration

. and user munual ng all the conditions wirh all .\]Jecific the integration provided in provided to the transmitter by the grantee, instructions rules appUcable lo the transmitter instructions by the grantee,

(8)The module must comply with RF exposure Answer: Yes; Transmitter Reports and Refer to modular installation meets MPE calculation mam requirements

<l47 CFR 1. 1307. Re_rto M PE Please contact Best Regards, me if you have any further questions. Thanks for your attention.

<Signature> Lt>

Title:

Quality Manager Company: lotelligent Co., Ltd

C5266091_X23_Ed.1 US AGENT LETTER OF ATTESTATION US Agent:

Company Name: THREE STONES MEDIA LLC Contact Name: Sijie Zhang Address:1200 Broadway St.APT 329, Los Angeles,CA90015 Telephone No:+1 267 909 3692 Fax No:

Email: abbyzhangmedia@gmail.com FRN: 0033401761 TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 This letter is to confirm that we have accepted the responsibility to act as US agent representative on behalf of the (Iotelligent Co., Ltd.) noted below for all future FCC certification/registrations rege ee mit the period of this agreement, which ends at the specified date below. As per US agent, we are aware of te redikemenis involved as outlined in FCC Equipment Authorization Program in their Report and Order FCC 22-84 and the clause 2.911 Application requirements. Applicant Company name: _Iotelligent Co., Ltd. Grantee code: 2BCD8 FCC ID: 2BCD8-ZK8201 Contact Name: Long Xu , Address: Room 2006, NO.1199 Defu Road, Jiading, Shanghai, China Telephone No: +8613901593750 Fax No: +8613901593750 Email: Long.xu@iotelligent.com The Applicant acknowledge the acceptance of its obligation to maintain an agent for Service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S. or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Date: 2023-08-17 Applicants Name: Long Xu US Agents Name:

Title: Project Manager Signature 1/1