www.iotgizmo.com Smart WiFi-Multi Dimmer Model : DSCR32 Smart Touch Dimmer Model : D6932 Requirements 2.4 GHz Wi-Fi router Neutral wire needed, 120V 60HZ for North America use Single pole switch only, converts 3-pole the single pole + app Dimmable bulbs (Compact Fluorescent Lamp (CFL), Incandescent, LED) Rated capacity 300W CFL and LED, 400W Incandescent Simple Installation Process Use screws to tighten dimmer to the electrical box Use electrical caps for calculating wires Step 1: Remove Old Switch/Dimmer
!
Caution Electrical Circuits with 120V AC are HAZARDOUS and could kill people by electrocu- tion. Only certied electrician shall perform the replacement or installation of Smart Dimmer. It is essential to turn-o the breaker supplying power to the switch being replaced with smart dimmer Figure A. Shows a typical residential electrical wiring of a switch. Two black wires are generally Line-In from the panel/breaker (Top Black) and bottom black wire Line-Out supplies electricity to the light xture. Some old houses Line-In and Line-Out may be reversed. In such case use electrical tester to nd Line-In by turning switch o. Tester indicating power is Line-In or supply wire and the other Line-Out is connected to the xture. Now turn o the breaker and install smart dimmer. Bare copper or green color conductor is GND wire which is grounded to the main panel. Remove all three wires and mark supply (Line-In) & xture black wires (Line-Out) with pen or and electrical tape. Use electrical caps on live wires to prevent accidental touching or shorting of the circuit. Figure A Figure B Step 2: Smart Dimmer Electrical Connections Figure B. Shows how to connect wires for the Smart Dimmer D6932. Black Dimmer Black wire connects to Line-In or Supply from Panel/breaker. White Dimmer White wire (Neutral) connects to group of white wires generally capped in the electrical box and tucked on the back side and is connected to panel/breaker. Red Dimmer Red wire (Line-Out/Load) connects to Black-Wire going to the light xture Green Dimmer Green Wire GND connects to ground wires in the electrical panel box. Step 3:
Step 3-A:
Power ON Circuit Breaker to continue installation of the iotGizmo Touch Dimmer Once the power is turned on by ipping the Circuit breaker you will see bottom White-LED blinking and lights turns ON. It means dimmer is connected right and is ready to control lights. User now can operate the dimmer by swiping nger up and down on the touch panel (Center Middle Portion on the dimmer surface) over the LEDS and experience light dimming or turning O & On. LEDS indicate proportional intensity control (Scale 0 to 100%). Bottom Blinking Led indicates WiFi configuration is not completed and smart-features are not yet enabled. Step 3-B:
Power ON Circuit Breaker to continue installation of the iotGizmo Multi Dimmer UP Down Step 4: Power ON Circuit Breaker-Energizing the Smart Dimmer Download iotGizmo app from the app-store for iOS and play-store for Android smart phones. Register at the website and create a login/password, there will be a conrmation email sent to the registered login-emailD. Click OK on the link and your credentials will be established for cloud-server access to control smart devices. Login to the app with login/password you have used to register. You shall see the following screen. Congure WiFi as shown in the screen below Select > WiFi cong menu option No service 9:30PM 72 %
LTE 9:30PM 95 %
WiFi config Add new device Remove device Logout Udates & Checks Bedroom Thermostat cad4c0 Kitchen Dimmer 4fba14 Hello, Welcome Email Password Sign in Sign up >
Forgot password >
copyrights all reserved by iotGizmo Corp Support NOTE: Your smartphone must be connected to your home router using 2.4GHZ wi band. Enter Password for your router(My WiFi) in the below screen prompt. LTE 9:30PM 95 %
LTE 9:30PM 95 %
LTE 9:30PM 95 %
Wi-Fi Configuaration Wi-Fi Configuaration Configuring device for My WiFi Configuring device for My WiFi Please enter Wi-Fi password ad click start button to finish device configuaration Type Wi-F- password here Start Please aprove the Wi-Fi iotGizmo Wants to Join Wi-Fi Network My WiFi?
Cancel Join Select Join and if the process is successful once shall see the right side screen. Wi-Fi Configuaration Configuring device for My WiFi Wi-Fi configuration is complete. Please wait until thermostat reboot to complete setup. OK Step 5: Adding Device & Controlling the Dimmer Once WiFi conguration is successful, the bottom LED will stop blinking and the dimmer can communicate with the app. The following screen will appear to allow you to name the dimmer (e.g: Kitchen, KthnLight, Living Rm, or TV Room, etc.) and adds to your device list. LTE 9:30PM 95 %
Succesfull Your device is succesfully set up and ready to work. Please name it. D10 Your can change it any time later in thermostat settings Start Once the IotGizmo Dimmer is added to your device list as shown below, you can control the dimmer from your smartphone. LTE 9:30PM 95 %
Dimmers D10 387 W 003080 Smart-Phone Control :
LTE 9:30PM TV Room 95 %
LTE 9:30PM TV Room 95 %
TAP ANYWHERE TO TURN ON/OFF TAP ANYWHERE TO TURN ON/OFF 3 3 41W 62%
+Step 6(A): Manual Dimmer operations - Touch Dimmer The dimmer can turn the light on or off by touching anywhere in the middle where the LEDs indicate the dimmer level. iotGizmo Dimmers always remember the previous brightness level and illuminate your lights to the previous setting. If you want to change the brightness level, slide finger or thumb up or down the middle over the LED indicators to set the dimmer to a desired level. Once again, you can turn the light on or off by touching anywhere in the middle along the LED indicators. LEDs will illuminate to indicate proportional light intensity. Step 6(B): Manual Dimmer operations - Multi Dimmer Dimmer can be operated by touching the circular portion of the LCD screen to turn on or off. Multi-dimmer always remembers previous brightness level and illuminate your lights (multiple room lights) to the previous setting. If you want to change brightness level slide thumb on touch panel in the clockwise direction to increase or decrease brightness. Once again turn light on or off by touching screen panel anywhere preferably in the center area. OFF ON Brightness control (50%) Group icon screen controls all lights in a single group. To operate the multi-dimmer for control of light in other rooms such as kitchen, family room and living room, swipe the fingers from right to left or left to right and control individual lights as show below. Left Right Manual Operation of Single Dimmer:
A B C Multi-dimmer always remembers previous brightness level of single dimmer and illuminate your lights to the previous setting. If you want to change brightness level, slide thumb on touch panel in the clockwise direction to increase or decrease brightness. If you want to turn light ON/OFF simply touch the panel, preferably in the center area. i) Kitchen Dimmer A B ii) Family Room Dimmer A B ON C OFF Brightness control
(50%) ON Brightness control
(50%) C Multi dimmer can controls a maximum of 3 single dimmers. OFF Step 7: Advanced features such as Lighting schedules etc. Advanced features are provided to automate light controls in order to save energy and for your convenience. The Multi Dimmer has an additional feature to add and remove other dimmers in a group. These features are all configured in the dimmer settings screen as shown below. LTE 9:30PM 95 %
D10 Settings Kitchen Dimmer Group settings ON / OFF SHUTOFF TIMER 30 MIN ON / OFF 255 Old New Brunswick Rd, Suite N350, Piscataway, NJ.... ON / OFF INTENSITY HOURS ON / OFF HOURS 100%
06:30 PM - 06:00 AM RANDOMIZE 00:00 AM - 00:00 AM Diagnostics and trouble shooting 1. 2. 3. 4. 5. If you are unable to configure WiFi and the device is in WiFi setup mode, check your router password is correct and also your router and smartphone are compatible to work with 2.4GHZ WiFi frequency. Also make sure you have decent WiFi signal strength at the location where this dimmer is installed. Generally metal boxes and metal surface-wall-plates hinder WiFi signals. WiFi antenna is mounted on the top front portion of the dimmer for optimal WiFi reception. If possible, use a plastic switch cover plate. Repeat the procedure once again by resetting power and/or rebooting the dimmer. Dimmer Reboot/Reset:
By gently touching or pressing the middle of the airgap toggle lever at the bottom. Changing Light bulbs The Airgap breaker disconnects power output to the light fixture and must be pulled out when changing light bulbs. Once Light bulbs are changed, push airgap switch back into position for the lights to operate. GEO AWAY - Turns light off automatically when away from set addressNIGHT MODE - Turns light on automatically for a set intervalAUTO SHUTOFF TIMER - Turns light off after a set timeDEVICEVACATION AWAY - Turns light on and off automatically at set times when away 6. Blinking/Flickering Lights:
Dimmable bulbs only work properly with these solid-state dimmers. Most CFL bulbs are not dimmable and also first generation of LEDs may not be dimmable. Please ensure that your bulb is dimmable. Using non-dimmable bulbs with smart dimmers may induce noise on the light circuitry and the dimmer may not behave properly. For further help contact us FCC caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
*
Download the iotGizmo App from the Appstore and Google play Contact Us iotGizmo Corporation 255 Old New Brunswick Rd, Suite N350 Piscataway, NJ, 08854, USA 1-732-734-4820 support@iotgizmo.com www.iotgizmo.com copyrights all reserved by iotGizmo Corporation - 2018 Thank you for saving energy.