FCC ID: 2AMRO-HLCRIO202 Easy One Touch Connect

Easy One Touch Connect Alexa Built-in Dashboard & Windshield Mount FRENCH Alexa Built-in Dashboard & Windshield Mount SPANISH Alexa Built-in Dashboard & Windshield Mount www.iottie.com cs@iottie.com 1 installation/installation/installation Getting Started For optimal mounting, please follow the detailed instructions within this manual when using the Easy One Touch Connect. For software installation, please see the Software Manual. iOttie is not liable for possible damages due to product misuse. Critical Information The Easy One Touch Connect is mounted with a semi-permanent adhesive tape. Each base is one-time use only. Once removed, it cannot be re-mounted. When mounting, it is recommended that the surface & product be above 40 F. Manuals should be followed in order: 1. Installation 2. Software 3. Skills. Specifications CHARGING PORT ITEM INPUT DEPTH WIDTH HEIGHT WEIGHT INPUT 12V~24V SPECIFICATIONS 5V - 1A Micro USB 2.25 4.25 3.6 3.345 oz OUTPUT USB A 5V - 2.1A MICRO USB 5V - 1A Car Charger Specifications At a Glance Whats in the Box:

Mounting Head, Base, and Dual Car Charger with Micro USB Cable Mute Button Foot Knob Cradle Knob Micro USB Port Easy One Touch Trigger Button Microphones Telescopic Knob Telescopic Arm Pivot Knob Lever Dashboard Pad Suction Cup Release Bars Foot Locking Side Arms Dual Car Charger with Micro USB cable Installation 1. Assembling the Mount A. Connect the Mount Cradle with B. Then, tighten the Cradle Knob. the Ball Joint. 2. Selecting a Location Choose an installation method: Dashboard/Flat Surface (A) or Windshield/Curved Glass (B) Option A Dashboard or Flat Surface Installation Choose an area on a flat surface on the vehicles dashboard and wipe any dust or debris from the surface. STICKY SUCTION CUP Option B Windshield Installation or Curved Glass Installation Choose a location on the windshield and wipe any dust or debris from the surface. STICKY SUCTION CUP 1. Peel off the protective film on the Suction Cup and press firmly onto the windshield. 2. Push Locking Lever down to engage suction. Connecting Power The Easy One Touch Connect is powered via a micro-USB cable. There is no off/

on switch on the device. Once it is plugged in, the device will remain on unless the vehicle shuts off power when in parking mode. 1. Peel off the film on the dashboard pad & stick on the desired installation location. 2. Peel off the protective film on the Suction Cup and press mount firmly onto the dashboard pad. 3. Push Locking Lever down to engage suction. 1. Plug the micro-USB cable into 2. Insert Car Charger into your the USB port on the back of the Mounting Head. vehicles power port. Using the Easy One Touch Mechanism Adjusting the Mount The Easy One Touch lock and release mechanism makes it simple to mount & retrieve smartphones in seconds. Mounting Step 1: Press the locking side arms in. Step 2: Press your device against the Easy One Touch trigger button. The mounts arms will automatically close on contact and hold the device during the driving journey. Releasing Press the locking side arms with one hand and retrieve the device. 1. Cradle Knob 2. Foot Knob When mounting in landscape mode, loosen to rotate the Cradle. Tighten to lock in desired position. Located on the lower back of Cradle. Loosen to re-position mounts foot. The Foot can be adjusted up & down or side-to-

side. 3. Telescopic Knob 4. Pivot Knob Located on top of Telescopic Arm, loosen to extend the arm, and tighten to secure distance. Located on the side of the Mount Base, turning allows you to pivot telescopic arm. Tighten to secure position. Operating temperature: -10-55C Operating frequency range: 2402-2480MHz Rated Power: For Classic: 9.1dBm, BLE: 8.1dBm Declaration of Conformity Hereby, iOttie, Inc. declares that the radio equipment type Easy onetouch connect of HLCRIO201 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.iottie.com This device may be used in each EU member state. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

HLCRIO201, HLCRIO202, HLCRIO203 The manufacturer's company name and address are shown in the user maunal. Easy One Touch Wireless back sticker Please add FCC CE information And Model Number

iOttie, Inc. Date: April 13, 2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

The iOttie, Inc.,the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen BALUN Technology Co., Ltd., to act on the behalf of the iOttie, Inc. solely in matters relating to the application for an FCC equipment authorization for FCC ID : 2AMRO-HLCRIO202 including the signing of documents in connection with this Application, Necessary acts carried out by Shenzhen BALUN Technology Co., Ltd. in connection with the Application shall have the same effect as acts of the iOttie, Inc. The iOttie, Inc also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Section 862. Yours Sincerely, caleb cho Mangaer iOttie, Inc

iOtie, Ine Date: April 13, 2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 RE: iOttie, Inc FCC ID: 2AMRO-HLCRIO202 FCC Certification Confidentiality Request Gentlemen:

This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. iOttie, Inc requests that the following documents regarding this submission for FCC ID: 2AMRO-

HLCRIO202 be kept Long-Term confidential:

Exhibit Type File Name Block Diagram Block Diagram.pdf Schematics Schematics.pdf Operational Description _ Operational Description.pdf And below exhibit kept short-term confidential (180 days):

Exhibit Type File Name External Photos External Photo.pdf Internal Photos Internal Photo.pdf Test Setup Photos Test Setup Photos.pdf Users Manuals Users Manual.pdf Those documents contain detailed system and equipment description and related information about the product which iOttie, Inc considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, iOttie, Inc considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Thank you for your attention to this matter. Yours Sincerely, Print name: caleb cho Title: Mangaer iOtie, Inc