PACKAGE CONTENTS
(image) Security Adapter Wiring Cables Mounting Kit p/n 210432 is designed and manufactured in the United States. mentioned are the Trademarks of their respective owner(s). This product EchoStar Technologies L.L.C. Other products, brands, and companies 80112. All rights reserved. EchoStar is a registered trademark of Copyright 2016 EchoStar Technologies L.L.C., Englewood, Colorado SAGE SECURITY ADAPTER QUICK START GUIDE Quick Start Guide Mounting Guide For all your customer needs, go to SAGEbyHughes.com. LIMITED WARRANTY One-year Limited Warranty. Limited Warranty details are available at SAGEbyHughes.com/warranty. SECURITY ADAPTER QUICK START GUIDE REGULATORY INFORMATION This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de license. Lexploitation est autorise aux deux conditions suivantes: (1) Lappareil ne doit pas produire de brouillage, et (2) Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If none of the remedies stops the radio interference, you should contact a licensed radio/
television technician, your satellite dealer, or visit SAGEbyHughes.com for assistance. Product must be installed at least 20 cm (~8 inches) from typical person locations, per FCC RF exposure regulations. Do not make changes or modi cations to this equipment. This could void the users authority to operate the equipment. SETUP AND INSTALLATION The SAGE Security Adapter allows you to integrate SAGE by Hughes with your existing home security system. Follow the instructions below to install your SAGE Security Adapter. 1 Using your SAGE remote, press HOME. 2 Select Settings. 3 Select Add Devices. 4 Select Sensors. 5 Select Security Adapter. 6 Follow the on-screen prompts to install and set up your SAGE Security Adapter, pair it to the SAGE Hub, and establish rules. IMPORTANT SAFETY NOTICE: Do not begin installation of your SAGE Security Adapter until you have carefully reviewed the installation instructions for your SAGE Hub, which includes important safety information. Installing the SAGE Security Adapter without reviewing these instructions, turning off the electric power to your existing home security panel and disconnecting its battery, may damage the security panel, the SAGE Security Adapter, and any attached devices. INSTALLATION OVERVIEW This page provides a general overview of how to integrate the SAGE Security Adapter into your existing home security system. For full instructions, visit SAGEbyHughes.com and download and/or print the installation instructions that correspond to your home security system. Step-by-step instructions will also be available on the TV connected to your SAGE Hub during installation. security system. 1 Identify the brand and model of your existing home 2 Choose where you want to install your SAGE Security Adapter: at your security systems central panel or at an individual keypad in your house. 3 If a company is monitoring your existing security system, notify them that youll be temporarily shutting off the system to install the SAGE Security Adapter. security system. 4 Wire the SAGE Security Adapter to your existing home 5 Pair the SAGE Security Adapter to your SAGE Hub. 6 Mount the SAGE Security Adapter. 7 Set up security zones in your home.