FCC ID: NRIHS1X0900 TRANS-HFD

LMD-109 Line Voltage Bi-Level Occupancy Sensor INSTALLATION INSTRUCTIONS Indoor dry location use only Utilisation a L'interieur Uniquement CAUTION Risk of Electric Shock - Disconnect power supply before servicing. Open Type Photoelectric Switches. Install the sensor at least 1ft. away from any occupant. PRUDENCE Risque de choc lectrique - Dbranchez l'alimentation avant l'entretien. Ouvrir Type commutateurs optolectroniques. IR-TEC hereby declares that the LMD-109 complies with Directive 2014/53/EU issued by the Commission of the European Community. The complete declaration of conformity is available on our website: www.irtec.com The frequency and maximum transmitted power in EU are listed as 5800 MHz: -11.28dBm. Federal Communication Commission Interference Statement FCC IDNRIHS1X0900 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

OVERVIEW The LMD-109 is a line voltage occupancy sensor designed for OEM lighting fixture integration with 0-10V output for bi-level dimming control. This occupancy sensor employs an advanced High Frequency Doppler (HFD) sensing technology to provide superior sensing performance of minor motion, such as typing, writing, or reading. The HFD technology is operating with high frequency radio waves which are capable of detecting the occupant's presence and movements without requiring unobstructed line-of-sight like a PIR sensor. Thus, the HFD sensor can detect through non-metallic material, such as plastic, glass, plywood or plaster board. The Accu-Set digitalized potentiometers make the sensor setting easier, faster and more accurate than the conventional analog ones. Four levels of sensitivity and control modes can be selected via DIP switch setting. An exclusive Hybrid Switching technology makes the LMD-109 perfect to control lighting with exceptionally high inrush current (HIC) during switching, such as multiple LED lightings connected in parallel. The sensor comes with an ambient light sensor (ALS) to inhibit switching on the light if the ambient light level is higher than the threshold set. DIMENSIONS 3.6mm

(0.14) APPLICATION NOTES Avoid placing the sensor in an area surrounded with metallic wall which may block or absorb the radio wave. If possible, place the sensor to the opening as close as possible. Fluorescent light may cause interference to the HFD sensor operation, and result in lighting permanent on. If possible, avoid placing the HFD sensor within 1m (3ft.) of fluorescent light. Avoid sensor placement facing doors, corridors or exits as HFD sensor may detect the traffics at adjacent area. HFD sensors are best for use in areas with partitions and high dividers, or high level of minor motion activities. The HFD sensor is more sensitive to the movements toward than across the sensor, so ensure to place the sensor at the position toward the movements of occupant. DETECTION PATTERN Mounting Height Coverage*

*Sensitivity 100%

3 m (10 ft) 180 m2 (2,000 ft2) 6 m (20 ft) 100 m2 (1,200 ft2) LMD-109 84mm

(3.3) 92mm

(3.6) 43mm

(1.69) 29mm

(1.69) Major motion Minor motion

(m) 0 3 6 9 30 6 20 3 10 0 0 3 3 6 20

(ft) 0 10 20

(m)

(ft) 9 30

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement:

IC ID22993-X09HS1AC602 This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. www.irtec.com Printed in Taiwan This product may be covered by one or more U.S. patents or patent applications. Please visit www.irtec.com for more information. P/N: 058-10901-002 IR-TEC International Ltd. 6 Rong An Road Luzhu Taoyuan 338 TAIWAN IR-TEC America, Inc. 590 W. Central Avenue Suite C Brea, CA 92821 USA WIRING DIAGRAM Gray Violet White Red Black L M D

-

1 0 9 I D M N L DIM DIM BALLAST LED DRIVER N L Neutral Line NOTE:

1. The driver/ballast MUST be 0-10V dimmable to achieve dimming control. 2. Ensure connection of LINE and NEUTRAL are not reversed to avoid damaging the sensor. 3. Ensure TOTAL isolation between DIM+/DIM- and GROUND to avoid damaging the sensor. 4. Conduct test with GROUND connected. L N SENSOR SETTINGS N The LMD-109 features 4 different control modes selectable via combination DIP switch #3 and #4, and 4 levels of sensitivity set via combination DIP switch #1 and #2. The LMD-109 also provides 7 different light-Off delay time and daylight threshold settings via 2 Accu-Set digital potentiometers marked T and L respectively. LMD-109 Sensitivity - SW1 & 2 The sensitivity and detection pattern of HFD sensor may vary with the furniture placement, partition layout, wall material, and shape of the space. For example, the detection pattern will become long rectangular if sensor is placed in a long corridor. 4 levels of sensitivity can be set via combinations of DIP switch #1 and #2. Sensitivity 100%

75%

50%

25%

DIP switch setting ON ON ON ON 3 2 1 4 ON-ON 3 2 1 4 ON-OFF 3 2 1 4 OFF-ON 4 3 2 1 OFF-OFF Control Mode - SW3 & 4 The combination of DIP switch #3 and #4 determines the sensing control mode. OSLATO OSLA OSO ON/OFF

: Occupancy Sensing at Low Ambient with Time-Off

: Occupancy Sensing at Low Ambient

: Occupancy Sensing Only

: ON-OFF Switching Mode Control (LMD-109) 3 2 1 4 L 5 6 7

(ALS disabled) ON 1 2 3 4 POS. TIME LUX 1 2 TEST 1 10 5 LUX 5 3 4 3 5 15 20 6 5 7 10 20 30 24H 25 60 TIME 5 3 7 1 7 3 1 3 2 1 4 T 5 6 7 OSLATO ON 3 2 1 4 ON-ON

(10 minutes)

(Factory set)

(Factory set) SW1 & 2 (100% Sensitivity) SW3 & 4 (OSLATO Mode) OSLA ON Position T (min.) L (lux) 1 T*

5 2 1 10 3 3 15 4 5 20 5 10 25 6 7 20 30 24H 60 Factory Set T - Delay Time The potentiometer T sets the period of delay time that sensor will turn off the connected lights after the area is vacated. L - Ambient Light Level The potentiometer L sets the ambient light level that the sensor will activate occupancy sensing control. 3 2 1 4 ON-OFF OSO ON 3 2 1 4 OFF-ON ON/OFF ON 1 2 3 4 OFF-OFF 1. 2. 3. 4. 5. 1. 2. 3. 4. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Dim the light to 30% after occupant leave and delay time elapses. Turn OFF the lights when 10 minutes TIME OFF delay elapses. When occupancy detected during TIME OFF, switch the light ON. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, dim the light to 30% under vacancy. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Dim the light to 30% after occupant leave and delay time elapses. NOTE: Not applicable for fixture internal integration. 1. 2. 3. 4. Ambient light is disabled with this mode. Dim the light to 30% at all time under vacancy. Switch the light to ON under occupancy. Dim the light to 30% after occupant leave and delay time elapses. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Turn OFF the light after occupant leave and delay time elapses. 1. 2. 3. TESTING To verify sensor control function normal, please proceed with the instructions as below to conduct test;

1. 2. 3. Set the arrow of T (DELAY TIME) potentiometer pointing at position "1" (TEST) and other setting to the desired threshold. Walk within the expected range at normal speed. The sensor will switch ON the light for 10 seconds whenever sensor detects the movement, and then switch OFF or DIM to 30% for 10 seconds as per the selected mode. The LED of sensor will also blink to indicate every motion detected. After testing complete ensure to set the T potentiometer to the position of desired time. NOTE: The sensor will automatically control the light as per the selected mode with factory set time delay (10 minutes) if the T potentiometer has NOT been set to other position. SPECIFICATIONS Power supply Maximum load

-Incandescent/Halogen 240VAC 5A 5A 5A 277VAC 1200/*750W(VA) 1200/*750W(VA) 1200/*750VA 120/240/277VAC, 50/60 Hz 120VAC 800/*500W(VA) 800/*500W(VA) 540/*500VA 25/50/75/100% selectable via DIP switch setting Zero-cross Hybrid-Switching Max. 80A for 16.7msec. 0-10V, 5%, non-isolated, max. 25 mA Up to 180 sq. m. @ 3 m (2,000 sq. ft @ 10 ft) 2.4 ~ 6 m (8 ~ 20 ft) 7 level Accu-Set digital potentiometer T/1'/3'/5'/10'/20'/30' , T=10 sec. for testing 10 min., OSLATO mode only Max. 95% RH

-40C~70C (-40F~158F) H92 x W43 x D29mm (H3.6"x W1.69"x D1.14")

-Fluorescent Ballast/CFL

-Ballast Electronic (LED) HFD sensitivity Load switching HIC protection Dim control Detection range Mounting height Ambient light level Delay time setting TIME OFF delay Op. humidity Op. temperature Dimensions

*Max load for operating temperature at 55C~70C (131F~158F) www.irtec.com

LMD-509 series Line Voltage Bi-Level Occupancy Sensor INSTALLATION INSTRUCTIONS CAUTION Risk of Electric Shock - Disconnect power supply before servicing. Open Type Photoelectric Switches. Install the sensor at least 1ft. away from any occupant. PRUDENCE Risque de choc lectrique - Dbranchez l'alimentation avant l'entretien. Ouvrir Type commutateurs optolectroniques. IR-TEC hereby declares that the LMD-509 complies with Directive 2014/53/EU issued by the Commission of the European Community. The complete declaration of conformity is available on our website: www.irtec.com The frequency and maximum transmitted power in EU are listed as 5800 MHz: -11.28dBm. Federal Communication Commission Interference Statement FCC IDNRIHS1X0900 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

OVERVIEW The LMD-509 series member of the TRANS family is a line voltage occupancy sensor with 0-10V output for bi-level dimming control. This occupancy sensor employs an advanced High Frequency Doppler (HFD) sensing technology to provide superior sensing performance of minor motion, such as typing, writing, or reading. The HFD technology is operating with high frequency radio waves which are capable of detecting the occupant's presence and movements without requiring unobstructed line-of-sight like a PIR sensor. Thus, the HFD sensor can detect through non-metallic material, such as plastic, glass, plywood or plaster board. The Accu-Set digitalized potentiometers make the sensor setting easier, faster and more accurate than the conventional analog ones. Four levels of sensitivity and control modes can be selected via DIP switch setting. An exclusive Hybrid Switching technology makes the LMD-509 series perfect to control lighting with exceptionally high inrush current (HIC) during switching, such as multiple LED lightings connected in parallel. The sensor comes with an ambient light sensor (ALS) to inhibit switching on the light if the ambient light level is higher than the threshold set. Like all sensors in the TRANS family, the LMD-509 series is also available in various mounting options. WIRING DIAGRAM 2 BALLAST LED DRIVER N L DIM DIM Gray Violet White Red Black 9 0 5

-

D M L M D I N L 1 BALLAST LED DRIVER N L DIM DIM Neutral Line NOTE:

1. The driver/ballast MUST be 0-10V dimmable to achieve dimming control. 2. Ensure connection of LINE and NEUTRAL are not reversed to avoid damaging the sensor. 3. Ensure TOTAL isolation between DIM+/DIM- and GROUND to avoid damaging the sensor. 4. Conduct test with GROUND connected. APPLICATION NOTES Avoid placing the sensor in an area surrounded with metallic wall which may block or absorb the radio wave. If possible, place the sensor to the opening as close as possible. Fluorescent light may cause interference to the HFD sensor operation, and result in lighting permanent on. If possible, avoid placing the HFD sensor within 3 ft. of fluorescent light. Avoid sensor placement facing doors, corridors or exits as HFD sensor may detect the traffics at adjacent area. HFD sensors are best for use in areas with partitions and high dividers, or high level of minor motion activities. The HFD sensor is more sensitive to the movements toward than across the sensor, so ensure to place the sensor at the position toward the movements of occupant. DETECTION PATTERN Mounting Height Coverage*

*Sensitivity 100%

3 m (10 ft) 180 m2 (2,000 ft2) 6 m (20 ft) 100 m2 (1,200 ft2) Major motion Minor motion

(m) 0 3 6 9 30 6 20 3 10 0 0 3 3 6 20

(ft) 0 10 20

(m)

(ft) 9 30

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement:

IC ID22993-X09HS1AC602 This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. www.irtec.com Printed in Taiwan This product may be covered by one or more U.S. patents or patent applications. Please visit www.irtec.com for more information. P/N: 058-50907-002 IR-TEC International Ltd. 6 Rong An Road Luzhu Taoyuan 338 TAIWAN IR-TEC America, Inc. 590 W. Central Avenue Suite C Brea, CA 92821 USA INSTALLATION The LMD-509 series can be mounted with a junction box into the ceiling, internally integrated or externally attached to a fixture to control the lighting with specific mounting bracket. Please refer to the mounting instructions separately attached for details of mounting options available. SENSOR SETTINGS The LMD-509 series features 4 different control modes selectable via combination DIP switch #3 and #4, and 4 levels of sensitivity set via combination DIP switch #1 and

#2. The LMD-509 series also provides 7 different light-Off delay time and daylight threshold settings via 2 Accu-Set digital potentiometers marked T and L respectively. Click!

To change the sensor setting, rotate the front cover counter-clockwise to remove. Replace the front cover after the setting complete. 3 2 1 4 L 5 6 7

(ALS disabled) L T 3 2 1 4 T 5 6 7

(10 minutes) ON 1 2 3 4

(Factory set) SW1 & 2 (100% Sensitivity) SW3 & 4 (OSLATO Mode) Position T (min.) L (lux) 1 T 5 2 1 10 3 3 15 4 5 20 5 10 25 6 7 20 30 24H 60 T - Delay Time The potentiometer T sets the period of delay time that sensor will turn off the connected lights after the area is vacated. Factory Set L - Ambient Light Level The potentiometer L sets the ambient light level that the sensor will activate occupancy sensing control. Sensitivity - SW1 & 2 The sensitivity and detection pattern of HFD sensor may vary with the furniture placement, partition layout, wall material, and shape of the space. For example, the detection pattern will become long rectangular if sensor is placed in a long corridor. 4 levels of sensitivity can be set via combinations of DIP switch #1 and #2. Sensitivity 100%

75%

50%

25%

DIP switch setting ON ON ON ON 3 2 1 4 ON-ON 3 2 1 4 ON-OFF 3 2 1 4 OFF-ON 4 3 2 1 OFF-OFF Control Mode - SW3 & 4 The combination of DIP switch #3 and #4 determines the sensing control mode. OSLATO OSLA OSO ON/OFF

: Occupancy Sensing at Low Ambient with Time-Off

: Occupancy Sensing at Low Ambient

: Occupancy Sensing Only

: ON-OFF Switching Mode Control (LMD-509Sx) OSLATO ON 3 2 1 4 ON-ON OSLA ON 3 2 1 4 ON-OFF OSO ON 1 2 3 4 OFF-ON ON/OFF ON 1 2 3 4 OFF-OFF 1. 2. 3. 4. 5. 1. 2. 3. 4. 1. 2. 3. 4. 1. 2. 3. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Dim the light to 30% after occupant leave and delay time elapses. Turn OFF the lights when 10 minutes TIME OFF delay elapses. When occupancy detected during TIME OFF, switch the light ON. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, dim the light to 30% under vacancy. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Dim the light to 30% after occupant leave and delay time elapses. Ambient light is disabled with this mode. Dim the light to 30% at all time under vacancy. Switch the light to ON under occupancy. Dim the light to 30% after occupant leave and delay time elapses. While ambient lux is higher than the level set, light stays OFF. While ambient lux is lower than the level set, and occupancy detected, switch the light ON. Turn OFF the light after occupant leave and delay time elapses. TESTING To verify sensor control function normal, please proceed with the instructions as below to conduct test;

1. 2. 3. Set the arrow of T (DELAY TIME) potentiometer pointing at position "1" (TEST) and other setting to the desired threshold. Walk within the expected range at normal speed. The sensor will switch ON the light for 10 seconds whenever sensor detects the movement, and then switch OFF or DIM to 30% for 10 seconds as per the selected mode. The LED of sensor will also blink to indicate every motion detected. After testing complete ensure to set the T potentiometer to the position of desired time. NOTE: The sensor will automatically control the light as per the selected mode with factory set time delay (10 minutes) if the T potentiometer has NOT been set to other position. SPECIFICATIONS Power supply Maximum load

-Incandescent/Halogen 240VAC 5A 5A 5A 277VAC 1200/*750W(VA) 1200/*750W(VA) 1200/*750VA 120/240/277VAC, 50/60 Hz 120VAC 800/*500W(VA) 800/*500W(VA) 540/*500VA 25/50/75/100% selectable via DIP switch setting Zero-cross Hybrid-Switching Max. 80A for 16.7msec. 0-10V, 5%, non-isolated, max. 25 mA Up to 180 sq. m. @ 3 m (2,000 sq. ft @ 10 ft) 2.4 ~ 6 m (8 ~ 20 ft) 7 level Accu-Set digital potentiometer T/1'/3'/5'/10'/20'/30' , T=10 sec. for testing 10 min., OSLATO mode only Max. 95% RH

-40C~70C (-40F~158F) 60 x H42 mm (2.36"x H1.65")

-Fluorescent Ballast/CFL

-Ballast Electronic (LED) HFD sensitivity Load switching HIC protection Dim control Detection range Mounting height Ambient light level Delay time setting TIME OFF delay Op. humidity Op. temperature Dimensions

*Max load for operating temperature at 55C~70C (131F~158F) www.irtec.com

LMS-109 series Line Voltage Occupancy Sensor INSTALLATION INSTRUCTIONS Indoor dry location use only Utilisation a L'interieur Uniquement CAUTION Risk of Electric Shock - Disconnect power supply before servicing. Open Type Photoelectric Switches. Install the sensor at least 1ft. away from any occupant. PRUDENCE Risque de choc lectrique - Dbranchez l'alimentation avant l'entretien. Ouvrir Type commutateurs optolectroniques. IR-TEC hereby declares that the LMS-109 complies with Directive 2014/53/EU issued by the Commission of the European Community. The complete declaration of conformity is available on our website: www.irtec.com The frequency and maximum transmitted power in EU are listed as 5800 MHz: -11.28dBm. Federal Communication Commission Interference Statement FCC IDNRIHS1X0900 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

OVERVIEW The LMS-109 series is a line voltage occupancy sensor designed for OEM lighting fixture integration to provide occupancy sensing control. This occupancy sensor employs an advanced High Frequency Doppler (HFD) sensing technology to provide superior sensing performance of minor motion like typing, writing, or reading. The HFD technology operates with high frequency radio waves which are capable of detecting the occupant's presence and movements without requiring unobstructed line-of-sight like PIR sensors. Thus, the HFD sensor can detect through non-metallic material like plastic, glass, plywood or plaster board. The Accu-Set digitalized potentiometers make setting the sensor easier, faster and more accurate than conventional analog ones. 4 levels of sensitivity can be selected via DIP switch settings to provide different coverage. An exclusive Hybrid Switching technology makes the LMS-109 series perfect to control lighting with exceptionally high inrush current (HIC) during switching, such as multiple LED lights connected in parallel. The sensor comes with an ambient light sensor (ALS) to inhibit switching on the light if the ambient light level is higher than the threshold set. DIMENSIONS 3.6mm

(0.14) LMS-109 84mm

(3.3) 92mm

(3.6) 43mm

(1.69) 29mm

(1.69) APPLICATION NOTES Avoid placing the sensor in an area surrounded with metallic wall which may block or absorb the radio wave. If possible, place the sensor to the opening as close as possible. Fluorescent light may cause interference to the HFD sensor operation, and result in lighting permanent on. If possible, avoid placing the HFD sensor within 1m (3ft.) of fluorescent light. Avoid sensor placement facing doors, corridors or exits as HFD sensor may detect the traffics at adjacent area. HFD sensors are best for use in areas with partitions and high dividers, or high level of minor motion activities. The HFD sensor is more sensitive to the movements toward than across the sensor, so ensure to place the sensor at the position toward the movements of occupant. DETECTION PATTERN Mounting Height Coverage*

*Sensitivity 100%

3 m (10 ft) 180 m2 (2,000 ft2) 6 m (20 ft) 100 m2 (1,200 ft2) Major motion Minor motion

(m) 0 3 6 9 30 6 20 3 10 0 0 3 3 6 20

(ft) 0 10 20

(m)

(ft) 9 30

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement:

IC ID22993-X09HS1AC602 This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. www.irtec.com Printed in Taiwan This product may be covered by one or more U.S. patents or patent applications. Please visit www.irtec.com for more information. P/N: 058-10900-002 IR-TEC International Ltd. 6 Rong An Road Luzhu Taoyuan 338 TAIWAN IR-TEC America, Inc. 590 W. Central Avenue Suite C Brea, CA 92821 USA OPERATION The LMS-109 series is a line voltage operating occupancy sensor with hybrid switching output to control the operation of connected load. The sensor will switch on the light when it detects the presence and movement of a moving object

(human, or vehicle) within its coverage, and automatically shut off the light after the delay time elapses. Different delay times can be programmed by an Accu-Set digital potentiometer. An ambient light sensor is built-in to inhibit switching on the light when ambient light level is higher than the threshold set. WIRING DIAGRAM Various control modes may be achieved by different wiring connections. Basic wiring diagrams are included as below for reference. Consult with an IR-TEC team member if a more complex control is required. Load Neutral Line e t i e t i h W h W k c a B l d e R N N L LMS-109 L N N SENSOR SETTINGS The LMS-109 provides 7 different light-Off delay time and daylight threshold settings via 2 potentiometers marked T and L respectively. 4 levels of sensitivity can be set via combination DIP switch #1 and #2. LMS-109 3 2 1 4 L 5 6 7

(ALS disabled) ON 1 2 3 4 POS. TIME LUX 1 2 TEST 1 10 5 LUX 5 3 4 3 5 15 20 6 5 7 10 20 30 24H 25 60 TIME 5 3 7 1 7 3 1 3 2 1 4 T 5 6 7

(10 minutes)

(Factory set)

(Factory set) SW1 & 2 (100% Sensitivity) SW3 & 4 (No Function) Position T (min.) L (lux) 1 T*

5 2 1 10 3 3 15 4 5 20 5 10 25 6 7 20 30 24H 60 Factory Set

*T=10 seconds shorten delay for testing convenience. The sensor will automatically resume to the factory default delay setting after 10 minutes, if the potentiometer has not been adjusted to other position. T - Delay Time The potentiometer T sets the period of delay time that sensor will turn off the connected lights after the area is vacated. L - Ambient Light Level The potentiometer L sets the ambient light level that the sensor will activate occupancy sensing control. Sensitivity The sensitivity and detection pattern of HFD sensor may vary with the furniture placement, partition layout, wall material, and shape of the space. For example, the detection pattern will become long rectangular if sensor is placed in a long corridor. 4 levels of sensitivity can be set via combinations of DIP switch #1 and #2. Sensitivity 100%

75%

ON 50%

ON 25%

ON ON DIP switch setting 1 2 1 2 1 2 1 2 ON-ON ON-OFF OFF-ON OFF-OFF NOTE: DIP switch #3 and #4 are not functional for LMS-109. SPECIFICATIONS Power supply Maximum load

-Incandescent/Halogen

-Fluorescent Ballast/CFL

-Ballast Electronic (LED) HFD sensitivity Load switching HIC protection Detection range Mounting height Ambient light level Delay time setting Op. humidity Op. temperature Dimensions 240VAC 5A 5A 5A 277VAC 1200/*750W(VA) 1200/*750W(VA) 1200/*750VA 120/240/277VAC, 50/60 Hz 120VAC 800/*500W(VA) 800/*500W(VA) 540/*500VA 25/50/75/100% selectable via DIP switch setting Zero-cross Hybrid-Switching Max. 80A for 16.7msec. Up to 180 sq. m. @ 3 m (2,000 sq. ft @ 10 ft) 2.4 ~ 6 m (8 ~ 20 ft) 7 level Accu-Set digital potentiometer T/1'/3'/5'/10'/20'/30' , T=10 sec. for testing Max. 95% RH

-40C~70C (-40F~158F) H92 x W43 x D29mm (H3.6"x W1.69"x D1.14")

*Max load for operating temperature at 55C~70C (131F~158F) WARRANTY IR-TEC International Ltd. warranties this product to be free of defects in materials or workmanship for a period of five years from date of shipment. There are no obligations or liabilities on the part of IR-TEC International Ltd. for consequential damages arising out or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, profit, or cost of removal, installation or reinstallation. www.irtec.com