FCC ID: 2AYGT-P200 P Series Pocket Thermal Camera

11 264006 www.iraytek.com.cn Pocket Thermal Camera Quick Start Guide IRay Technology Co., Ltd. 2021 IRay Technology Co.,Ltd. All rights reserved worldwide. All contents in this manual, including words, pictures, images, etc., belong to IRAY TECHNOLOGY CO., LTD.

(Hereinafter referred to as THE COMPANY or IRAY TECHNOLOGY). No part of the manual, in whole or in parts, may be copied, photocopied, translated, or transmitted without the prior written permission of IRAY TECHNOLOGY. Any third party shall not modify, crack, decompile or delete the documents, systems, software and programs contained in the thermal camera without the consent of the company before it is sold to the end user, and shall not dismantle the terminal product or preinstall other equipment on the thermal camera without authorization. The Company authorizes end users to use the camera within the scope of authorization and in the areas where the thermal camera has obtained patent rights. Anyone shall not dismantle, modify, crack, decompile or make other changes to the thermal camera without authorization or through any third party. The users should bear the relevant responsibilities of camera damage, abnormal function, unstable operation caused by above behaviors without authorization. In case of any damage caused by the above behaviors, the company reserves the right to pursue its legal liability. Cautions 1 72 11 264006 www.iraytek.com.cn External Power Operation: DC 5V. Do not exceed the maximum angle of 90 when rotating the lens to avoid damage to the Please do not make the objects fall onto the camera or vibrate the camera violently, and keep the camera far away from magnetic applications. In order to avoid damage to lens or detector, do not aim the lens to the strong heat light sources, such as the sun. Please do not use the camera under the environment of extremely cold or hot, high humidity or dusty atmosphere; The recommended working temperature is -10 ~+50

. The camera should be placed in dry environment without corrosive gas and avoid direct camera. sunlight. Please keep all packaging materials, so you can send the camera to the agent or the manufacturer with the original packaging in case it can not work normally. If the camera can not work properly, please contact the agent or after-sales services. Do not disassemble or modify the camera. The company does not undertake any responsibility for problems caused by unauthorized modification or maintenance. 1. Camera Appearance 7 8 9 1 2 3 4 5 6 1. Lens rotation module 2. Tripod mount 3. Touch screen 4. Microphone 5. Power indicator 6. USB-C connector 2 72 10 11 264006 www.iraytek.com.cn 7. Digital camera 8. Infrared lens 9. LED lights 10. On/off button 11. Lanyard attachment point 2. Lens Rotation The lens module can be rotated at angles of 0, 30, 60 and 90. 3. Main Interface The picture on the left shows the main interface, and the lower part is the main menu. There are 5 icon buttons, which can be selected by sliding left or right or click to enter the secondary fan-shaped menu; The picture on the right shows the fan-shaped secondary menu, containing 3-7 icon buttons. 4 icon buttons are displayed by default, and other icons can be displayed by sliding the secondary menu clockwise or counterclockwise on the touch screen. 4. Basic Operations 4.1 Switching and Charging Long press the power button to turn on or turn off the camera, and short press the button to turn on/off the screen display. The camera can be charged by USB cable no matter it is turned on or off. The light at the bottom will light up during charging. Red indicates not fully charged, and green indicates fully charged. 3 72 11 264006 www.iraytek.com.cn 4.2 Measuring Mode On the main interface, tap the icon button on the main menu bar to enter the secondary fan-shaped menu, which contains six icons, and four are displayed by default. The remaining icons can be displayed by sliding the secondary fan-shaped menu clockwise or counterclockwise. Six measurement modes can be set: center spot, highest temperature, lowest temperature, spot, line and region. Click anywhere on the screen to hide and exit the menu. 4.3 Image Mode On the main interface, tap the icon button on the main menu bar to enter the secondary fan-shaped menu which contains four icons. Four image modes can be set: thermal, fusion, PIP and visible. Click anywhere on the screen to hide and exit the menu. 4.4 Image Capturing and Image Viewing On the main interface, tap the icon button on the main menu bar to captue image or enter the secondary fan-shaped menu, which contains four icons: capturing images, entering the gallery, turning on/off the fill light and performing shutter correction. Click anywhere on the screen to hide and exit the menu. 4.5 Palettes On the main interface, tap the icon button on the main menu bar to enter the secondary fan-shaped menu, which contains seven icons, and four are displayed by default. The remaining icons can be displayed by sliding the secondary fan-shaped menu clockwise or counterclockwise. Seven palettes can be selected: blackhot, whitehot, iron red, lava, rainbow, rainbow HC, black red. Click anywhere on the screen to hide and exit the menu. 4.6 Other Settings On the main interface, tap the icon button on the main menu bar to enter other settings. Eight setting items are included: measuring parameters, measuring mode, below/above alarm, Wi-Fi, image capturing, auto power-off, screen rotation, and system settings. You can select and set the relevant setting options through the touch screen. Click the icon in the top left corner to return to the main interface after setting. The system settings include nine secondary settings: device information, date and time, language, unit settings, screen brightness, formatting the SD card, USB mode, restoring factory default, and upgrading software. After setting, click the icon in the top left corner to return to the first-level interface. 4 72 11 264006 www.iraytek.com.cn FCC Caution. 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. SAR Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. 5 72 Appendix: Emissivity of Common Materials 11 264006 www.iraytek.com.cn Material Human Skin Printed Circuit Board Cement Concrete Ceramics Rubber Wood Pitch Brick Sand Soil Cardboard White Sticky Membrane Paper Water Snow Marble Polished Glass AAO Oxidized Iron Oxidized Steel Oxidized Stainless Steel Emissivity 0.98 0.91 0.92 0.92 0.95 0.90 0.96 0.93 0.90 0.92 0.90 0.93 0.96 0.85 0.94 0.94 0.55 0.64 0.79 0.85 IRay Technology Co., Ltd. Tel:400-998-3088 Fax: 0535-3410604 Email: sales@iraytek.com Website: www.infiray.com Address: No.11 Guiyang Street, YEDA, Yantai, China. 6 72

IRay Techonlogy Co.,Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021/12/29 Subject; Request for Confidentiality FCC ID: 2AYGT-P200 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM List In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Peng Zhang Title: Quality supervisor

C5266091_X8_Ed.1 Letter of Authorization Company: IRay Technology Co., Ltd. Address: 11GUIYANG STREET, YANTAI ECONOMY AND TECHNOLOGY DEVELOPMENT DISTRICT, YANTAI SHANDONG P.R.CHINA Product Name: P Series Pocket Thermal Camera Model Number: P200, P2ABCDEYXX(A=00~99;B=A,S,U;C=C,G,N;D=A,F,E,M;E=00 PVTIRBCDEYXX(B=A,S,U;C=C,G,N;D=A,F,E,M;E=0000~99 00~9999;Y=A~Z), 99;Y=A~Z) FCC Identifier: 2AYGT-P200 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name:

Title:

Signature of applicant:

Date: 2021-12-29 Quality supervisor Peng Zhang 1/1

Dear Sir, Declaration Letter For our business issue and marketing requirement, we would like to list below model numbers on the certificates and reports, as following:

Main Model: P200 Serial Model No.:

P2ABCDEYXX(A=00~99;B=A,S,U;C=C,G,N;D=A,F,E,M;E=0000~9999;Y=A

~Z), PVTIRBCDEYXX(B=A,S,U;C=C,G,N;D=A,F,E,M;E=0000~9999;Y=A~Z) We declare that the difference of these is listed as below:

The only difference is the model name for difference market Signature:

Name/Title: Peng Zhang & Quality supervisor Company name: IRay Technology Co., Ltd. Tel: 086-18562243217 E-Mail: pzhang@iraytek.com Address: 11GUIYANG STREET, YANTAI ECONOMY AND TECHNOLOGY DEVELOPMENT DISTRICT, YANTAI SHANDONG P.R.CHINA Date: 2021/12/30