all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User manual | Users Manual | 755.46 KiB | January 28 2022 | |||
1 2 |
|
Int photo | Internal Photos | 2.23 MiB | January 28 2022 | |||
1 2 |
|
Ext photo | External Photos | 670.46 KiB | January 28 2022 | |||
1 2 |
|
label | ID Label/Location Info | 202.14 KiB | January 28 2022 | |||
1 2 |
|
Agent Authorization | Cover Letter(s) | 96.75 KiB | January 28 2022 | |||
1 2 | Block | Block Diagram | January 28 2022 | confidential | ||||
1 2 |
|
FCC long Term Confidentiality | Cover Letter(s) | 92.72 KiB | January 28 2022 | |||
1 2 | OP | Operational Description | January 28 2022 | confidential | ||||
1 2 |
|
SAR report | RF Exposure Info | 2.67 MiB | January 28 2022 | |||
1 2 | SCH | Schematics | January 28 2022 | confidential | ||||
1 2 |
|
Test photo | Test Setup Photos | 376.31 KiB | January 28 2022 | |||
1 2 |
|
Test report | Test Report | 2.86 MiB | January 28 2022 |
1 2 | User manual | Users Manual | 755.46 KiB | January 28 2022 |
l a u n a M g n i t a r e p O L 0 5 D T e b u T r o o d t u O y a R i f n I Operating Manual V1.0 Tube Serise Digital Night Vision Scope TD50L defective, send the device to our after-sales service for repair. IMPORTANT SAFETY INFORMATION Environmental influences WARNING! Never point the lens of the device directly at intense heat sources such as the sun or laser equipment. The objective lens and eyepiece can function as a burning glass and damage the interior components. The warranty does not cover damage caused by improper operation. Risk of swallowing Caution: Do not place this device in the hands of small children. Incorrect handling can cause small parts to come loose which may be swallowed. Safety instructions for use
Handle the device and battery pack with care: rough handling may damage the battery pack. Do not expose the device to fire or high temperatures. Only use the battery charger included in the delivery package. The battery capacity decreases when operated in a cold ambient temperature. This is not a fault and occurs for technical reasons.
Always store the device in its carrying bag in a dry, well-ventilated space. For prolonged storage, remove the batteries. Do not expose your device to extreme temperatures lower than - 20C and higher than + 50C. The product shall only be connected to a USB Type C interface. If the device has been damaged or the battery is
InfiRay Outdoor Tube TD50L Operating Manual
- 1 -
defective, send the device to our after-sales service for when you purchase a corresponding new product. The repair.
Safety instructions for the power supply unit Check the power supply unit, cable and adapter for visible damage before use. Do not use any defective parts. Defective components Do not use the power supply unit in wet or humid Only use the original cable provided with the battery must be replaced. environments. charger. Do not make any technical modifications. For further information and safety instructions, please refer to the Operation Instructions provided. This is also available on our website in the download center: www.infirayout-
door.com. User information on the disposal of electrical and electronic devices (private households) The WEEE symbol on products and/or accompanying documents indicates that used electrical and electronic products must not be mixed with ordinary household waste. For proper treatment, recovery and recycling, take these products to the appropriate collection points where they will be accepted without charge. In some countries, it may also be possible to return these products to your local retailer proper disposal of this product serves to protect the environment and prevents possible harmful effects on human beings and their surroundings, which may arise as a result of incorrect handling of waste. More detailed information on your nearest collection point is available from your local authority. In accordance with state legislation, penalties may be imposed for the improper disposal of this type of waste. For business customers within the European Union Please contact your dealer or supplier regarding the disposal of electrical and electronic devices. He will provide you with further information. Information on disposal in other countries outside of the European Union This symbol is only applicable in the European Union. Please contact your local authority or dealer if you wish to dispose of this product and ask for a disposal option. Intended use The device is intended for displaying heat signatures during nature observation, remote hunting observations and for civil use. This device is not a toy for children. Use the device only as described in this instruction manual. The manufacturer and the dealer accept no liability for damages which arise due to non-intended or incorrect use.
- 2 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 3 -
Handle the device and battery pack with care: rough handling may damage the battery pack. Do not expose the device to fire or high temperatures. Only use the battery charger included in the delivery package. The battery capacity decreases when operated in a cold ambient temperature. This is not a fault and occurs for technical reasons. Always store the device in its carrying bag in a dry, well-ventilated space. For prolonged storage, remove the batteries. Do not expose your device to extreme temperatures lower than - 20C and higher than + 50C. The product shall only be connected to a USB Type C interface. If the device has been damaged or the battery is Function test
damage. image. Before use, please ensure that your device has no visible Test to see if the device displays a clear, undisturbed Check that the settings for the scope are correct. See the notes in the section Operation. Installing/removing the battery The Tube series digital night vision scope is equipped with two power supply systems one built-in battery pack and one replaceable 18500 battery. The built-in battery pack cannot be removed. Observation with and without glasses Thanks to the flexible eyeshade, the Tube series can be used with or without glasses. It offers a full field of view in both cases. SPECIFICATIONS Model Detector Specifications Sensor Resolution, pixels Frame Rate, Hz Optical Specifications Objective Lens, mm Field of View, Optical Magnification, Smooth Zoom Eye Relief, mm Diopter Adjustment, D Detection Range, m Display Specifications Type Display Resolution, pixels Video Record Resolution, pixels Capture Resolution, pixels Battery Power Supply Battery Type Operating Time
(at temp.=22C) *, h Physical Specifications Scope Diameter, mm Max. Recoil Power on Rifled Weapon, g Degree of Protection, IP code Memory Capacity, GB Weight (Without the 18500 Battery), m/s2 TD50L 1440 1080 50 50 / F1.2 6.6 4.9 4.0 ~ 16.0 Support 70
-4 ~ +4 600 LCOS 1280 960 1280 960 1280 960
>13 30 1000 IP67 16 1000g(g=9.8m/s2) Built-in 6600mAh battery pack + one replaceable 18500 battery External Power Supply 5V (Type C USB)
- 4 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 5 -
Model Dimension, mm APP / Wi-Fi TD50L 395 85 75 Support (InfiRay outdoor) Stadiametric Rangefinder Support IR Illuminator**, nm 850 / 940 (Optional) Max Power of IR Illuminator, w 2.2
Actual operation time depends on the density of Wi-Fi use and video recording functions.
The product package does not contain the IR illuminator. Please select 850nm/940nm IR illuminator according to your own needs. Improvements may be made to the design and software of this product to enhance its features without prior notice to the customer. The current version of the User Manual is available on our official website: www.infirayoutdoor.com. PACKAGE CONTENTS Tube TD50L Digital Night Vision Scope Eyeshade Mounting for picatinny rail IPB-3 portable bag USB-C cable Power adapter Lens cleaning cloth Certificate of qualification DESCRIPTION Tube series digital night vision scope is a daytime and night dual-use scope designed for outdoor hunting. It is equipped with a starlight-level low illuminance chip, which can restore true colors and details in both day and night. The Tube series has a variety of battery-powered solutions with long operating hours, and can be widely used for hunting, observation and positioning in low visibility conditions. It adopts a 30mm standard pipe diameter to meet the requirements of the general clamp interface. PRODUCT FEATURES Starlight low illuminance sensor High image quality Smooth zoom Dual power supply system, with long battery life Standard 30mm pipe diameter Stadiametric rangefinder Long detection distance Built-in memory card, supporting photo taking and video recording Built-in Wi-Fi module, supporting app connection Support PIP function (Due to some factors, this function is not available for some regions) Convenient operation interface
- 6 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 7 -
0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. COMPONENTS AND CONTROLS BUTTON DESCRIPTION Button Power Button Current Status Powered off Home screen Standby Press and Hold Rotate Power on the device Shut down the device Main menu screen Press Standby Wake up the device Return to the upper menu without saving changes Switch between image modes Palette button Home screen Brightness button Home screen Adjust the display brightness Camera button Home screen Take a photo Turn on/off the PIP function Turn on/off the stadiametric rangefinder function Start/Stop video recording Rotary encoder Home screen Shortcut menu interface Open the shortcut menu Adjust specific parameters of a function Open the main menu Adjust image magnification Save and back to the home screen Switch between menu options /
1. Eyeshade 8. USB cover 2. Eyepiece adjusting ring 9. Type-C port 3. Camera button 10. LED indicator 4. Brightness button 11. Extend battery cover 5. Power button 6. Palette button 7. Rotary encoder 12. 18500 battery 13. Lens focus ring 14. Lens cover
- 8 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 9 -
If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. 0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. Button Current Status Press Press and Hold Rotate Confirm the option parameters
/ Open the submenu Switch between the X axis
/ Y axis Main menu interface Zeroing interface Save and back to the main menu Move reticle position:
Clockwise:
move to the left / down direction;
Anticlock-
wise: move to the right /
up direction POWER SUPPLY The Tube series adopts a dual power system (built-in chargeable Lithium-ion battery pack and a replaceable 18500 battery). The normal working time of the dual power supply system can be up to 13 hours. Also, Tube series can support the USB power supply. Please notice that the battery should be fully charged before first use. Charging the Built-in Battery During use, if the built-in battery icon turns into , it indicates that the battery level is low. Please charge the battery in time to avoid reducing the service life of the device due to over discharge of the battery. Rotate the USB cover (8) counterclockwise and remove it. Connect the Type-C end of the attached data cable
(15) to the Type-C port (9) on the Tube series. Connect the other end of the data cable (15) to the USB port on the power adapter (16). Plug the adapter
(16) into a 100-240V power socket (17) for charging. During charging, a charging icon appears on the right of the battery icon, and the LED indicator on the device is red. When the indicator turns green, it indicates that charging is complete. Note
The USB port can only be used for charging the built-in battery pack. Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray.
- 10 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 11 -
If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of 0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. Installing 18500 battery Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of
- 12 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 13 -
0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. 0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. EXTERNAL POWER SUPPLY The Tube series supports external power supplies, such as the portable power source for a mobile phone (5V). Connect an external power supply to the USB port (9) of the Tube device. Then, the device automatically switches to the external power supply and charge the internal battery pack at the same time. When the external power supply is turned off, the device switches to the replaceable 18500 battery for power supply. If no replaceable 18500 battery is installed or the battery level is low, it will switch to the built-in battery pack, instead of shutdown. INSTALLATION OF RIFLE MOUNT To ensure firing accuracy, please fix the Tube at a proper position on the weapon. The Tube series needs to be fixed with an adapter clamp, such as a simple Picatinny rail clamp provided in the package. The Tube series adopts a tubular body design with a diameter of 30mm, which is compatible with standard mounts with a diameter of 30mm, such as those of day scope. Proper tools can be used to install the Tube series according to the supplier's installation suggestions and steps. During installation, the installation position of the Tube device should be adjusted according to the distance between eye and eyepiece (eye relief) as specified in the Specifications and the sense of use and comfort. Failure to comply with this recommendation may result in injury to the shooter by the parts of the scope eyepiece when shooting. It is recommended to install the scope as low as possible, but keep it away from the barrel or other devices. It is recommended to use a torque wrench to tighten the screws of the installation clamps, so as to avoid damaging the scope body due to being over-tight-
ened, and the recommended torque shall not exceed
- 14 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 15 -
If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. 0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. 2.5nm. Before using the scope for hunting, please zero the device first according to the instructions as specified in the Zeroing section in this manual. It is recommended to use an eyeshade while using the scope in the dark in order to avoid detection of camouflage. Mounting the eyeshade on the eyepiece is carried out through the thread. OPERATION Open the lens cover (14). If the outdoor light is strong, you can close the lens cap to prevent the image from overexposure. 3s. Press and hold the power button (5) for 2s to power on the device. Then, the home screen appears after Rotate the eyepieceadjustingring (2) to adjust the resolution of the icon on the display. Rotate the lens focus ring (13) to focus on the object being observed. Setting the image mode: On the home screen, press the palette button (6) to set the image palette mode, which is day-night in sequence, and the icon on the top status bar is updated in real-time. Setting the display brightness: On the home screen, press the brightness button (4) to set the display brightness level from level 1 to level 5. Meanwhile, a short prompt for the corresponding brightness icon appears at the top status of the display. Setting the image sharpness: Press the rotary encoder (7) to enter the shortcut menu, and set the image sharpness (refer to the section Shortcut Menu for details). Power off: After using the device, press and hold the power button (5) for 3 seconds to enter the power-off interface with a shutdown countdown. Release the button when the countdown icon turns to 0, then a prompt interface "Data saving ..." is displayed. When the data is saved, the display turns black and the device is off. During the saving data, do not disconnect it from the power source, otherwise, the data cannot be saved. Standby: On the home screen, press the power button (5) briefly to standby the device. And press the power button (5) again to wake up the device. Turn reticle on: The reticle function is disabled by default, so functions related to the reticle are hidden, such as the shortcut menu, zeroing function in the main menu. So, when using the scope for the first time, press and hold the Brightness (4) + Palette (6) buttons at the same time for more than 15s to turn the reticle on. The shortcut menu and the zeroing function will be enabled automatically.
- 16 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 17 -
If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. 0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. ZEROING The Tube series adopts the freezing zeroing method. It is recommended to perform zeroing in environments within the operating temperature range of the scope. Fix the scope with the mount clamp on your weapon. For details, refer to the section Installation. Select a target at a certain distance, such as 100m, 200m, etc. Adjust the scope according to the operating instructions as described in the section Operation. Select the zeroing profile (refer to Main Menu -
Reticle Setup - Zeroing Profile function). Press and hold the rotary encoder (7) to enter the main menu interface, select the zeroing option, and press the rotary encoder (7) to enter the submenu of the zeroing function (refer to Main Menu - Zeroing). According to the selected target distance, select or add the new zeroing distance (refer to Main Menu -
Zeroing - Zeroing Distance - Set Zeroing Distance). When the zeroing distance is set up, rotate the encoder (7) to select the zeroing function, and press the encoder (7) to enter the zeroing interface (refer to Main Menu - Zeroing - Zeroing Distance -
Zeroing). The coordinate positions of the reticle (X axis and Y axis) are displayed in the upper left corner of the display. shoot. Point the weapon at the center of the target and Observe the position of the actual point of impact, and assume that the red mark in the figure on the right is the position of the point of impact (This mark is only for illustration. It should actually be a bullet hole). If the impact point does not match with the aiming point (the center of the scope reticle), keep the aiming position still, and meanwhile, press and hold the Palette (6) +Camera (3) buttons to freeze the picture, and then a snow-like freezing icon appears under the coordinate position on the upper left corner of the display. Turn the rotary encoder (7) to move the reticle. Rotate clockwise to move the reticle leftward or downward, and rotate anticlockwise to move the reticle rightward Press the rotary encoder (7) to switch between the X axis and Y axis, and the position of the cursor indicates the currently selected item with the icon After moving the reticle, a little white dot appears on the display, indicating the position of the reticle before When the reticle overlaps the actual point of impact, press and hold the rotary encoder (7) to save the current reticle position and return to the main menu Repeat aiming and shooting, until the position of the or upward. turning blue. moving. interface.
- 18 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 19 -
0C to +40C. Otherwise, the battery life will be significantly reduced. When charging, please do not leave the battery unattended. Do not connect the battery to the power supply for more than 24 hours after it is already fully charged. It is not recommended to connect third-party devices that consume more energy than the allowed value. The device is equipped with a short circuit protection system, but conditions that may lead to a short circuit should be avoided. The recommended operating temperature for the device is -20C to +50C. Do not use the device beyond this temperature range, or else, it may shorten the battery life. defect. When using the device at low temperatures, the battery capacity decreases. This is normal and not a Do not use the device at the temperatures above 50C this may decrease the batterys life. Keep the battery out of the reach of children. If there is no replaceable battery in the device, only the green icon of the built-in battery is displayed on the right. If the both batteries are fully charged, the replaceable battery will be preferred to power the device. If the replaceable battery level is low, the device will switch to the built-in battery automatically. When connecting to the external power supply using the USB port (9), it will switch to the external power supply automatically. At this time, a lightning charging icon is displayed above the built-in battery icon on the right of the display, which indicates that the built-in battery is being charged. When the device is in use, it is possible to change the replaceable battery without powered on. At this time, it will switch to the internal battery automatically. Safety Measures When charging, always use the 5V2A power adapter compatible with the device. Using any other type of adapter may cause irreversible damage to the battery or the adapter itself. If the device is not in use for a long time, the battery should be partially charged, not fully charged or discharged. Do not charge the device immediately after it is moved to a warm environment from a cold environment. Wait for 30 to 40 minutes for preheating. If the charger is modified or damaged, do not use it. The device should be charged at a temperature of before photographing and video recording. Please download the APP operation manual from our official website (www.infirayoutdoor.com) for detailed operation steps. Photographing On the home screen, briefly press the camera button
(3) to take a photo. A photo icon will appear on the upper left corner of the display when the image is frozen for 0.5 seconds. The images taken are saved in the built-in memory space. Video Recording On the home screen, press and hold the camera button (3) to start the video recording. A recording icon and a prompt box showing the recording time will appear in the upper right corner of the display, with the time format as 00:00:00 (hours:
minutes: seconds). During recording, you can also take a photo by briefly pressing the camera button (3). Stop the recording and save the video with a long press of the camera button (3). The videos and images taken are saved in the built-in memory space. Turn the battery cover (11) counterclockwise and remove it. Install the 18500 battery (12) into the battery compartment along the special label in the battery compartment designed for it, that is, the positive pole faces inward and the negative pole faces outward. Close and tighten the battery cover (11) by turning it clockwise. Switching between the two batteries If both batteries are installed in the Tube device, two battery icons are displayed on the right of the status bar below the image, with the replaceable battery icon on the left and the built-in battery icon on the right. The battery from which the device is powered is displayed in green, inactive - in gray. point of impact is consistent with that of the aiming point. Note After the zeroing position is set up, you can switch
the options of Zeroing Distance in the shortcut menu. DIGITAL ZOOM The Tube series Scope supports the Infinite zoom function of 4.0 - 12.0, by which you can magnify an image by 1 to 4 times. On the home screen, turn the rotary encoder (7) to zoom in/out the image. Zoom in by rotating clockwise, and zoom out by rotating anticlockwise. The magnification is displayed on the top status bar in real-time. Each time you rotate the rotary encoder, the image is zoomed in or out by 0.4 times. PHOTOGRAPHING AND VIDEO RECORDING The Tube TD50L is equipped with a built-in 16GB memory space, which support to take photos and record video for an observed target. The image and video files will be named after time, so it is recommended to set the system date and time in the main menu (Main Menu -
Settings - Date/Time), or synchronize the system date and time on the Settings page of the InfiRay Outdoor App
- 20 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 21 -
Note
recording. The menu can still be operated during video
The images and the videos are stored in the built-in memory card in the format of IMG_HHMMSS_XXX.jpg
(for images) and VID_HHMMSS.mp4 (for videos). HHMMSS - hours/minutes/seconds, XXX - three-digit common counter for photos which is NOT reset. If a file is deleted from the list, its number is not taken by the other file. The maximum duration of a video recording file is 10 minutes. When the duration is more than 10 minutes, the video will be automatically recorded onto a new
file.
The number of files is limited by the capacity of the built-in memory space of the device. It is suggested to check the available space of the memory card regularly and transfer your videos and images to other media to free up the space on the memory card.
The reticle is displayed on the captured videos or images, but GUI icons are not. Memory Access When the device is powered on and connected to a computer, it will be recognized by the computer as a flash memory card. Then, you can access the memory of the device and copy images and videos. Connect the device to a computer through the data cable. Power on the device. Double click "My Computer" on the desktop of your computer - double click to open the device named
"Infiray" - double click to open the device name
"Internal Storage" to access the built-in memory. the folders There are different folders named by time in the format of xxxx (year) xx (month) xx (day). Recorded photos and videos in that day are saved in Select desired files or folders to copy or delete. STATUS BAR The status bar, at the top of the image interface, shows information about the device's current operations. From left to right, they are:
1. Current image mode ( : day mode; : moon mode; : star mode) 2. Current zeroing profile and zeroing distance (e.g., A100m) 3. Current optical magnification (e.g., 4.0) 4. Current display brightness (level 3 is default) 5. Standby status and time (off is default) 6. Wi-Fi ( : Wi-Fi is on, : Wi-Fi is off) 7. Time (Can be set up in the main menu or synchronize the time in the InfiRay Outdoor App) 8. The power status of the replaceable battery (when 18500 battery is installed) 9. The power status of the built-in battery pack
- 22 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 23 -
Colored battery icon indicates that the battery is supplying power. The levels of it show the remaining battery life. Icon Color/Status Battery Status Green more than 40%
Yellow 20% - 40%
Red Less than 20%, need to charge instantly Lightning icon inside External power supply meanwhile charging the built-in battery pack SHORTCUT MENU The shortcut menu can be used for a quick setup of the basic settings of some common functions, including reticle style, reticle color and zeroing distance. On the home screen, press the rotary encoder (7) to enter the shortcut menu interface. Rotate the rotary encoder (7) to switch between the following function options, and the icon background of the selected option will be highlighted:
Reticle Color : Rotate the rotary encoder (7) to select the option, and press the rotary encoder
(7) to adjust the colors in the sequence of white, black, red and green.
Reticle Style : Rotate the rotary encoder (7) to select the reticle style, and press the rotary encoder (7) to switch among 6 styles. Zeroing Distance : Rotate the rotary encoder
(7) to select the option, and press the rotary encoder (7) to switch between the distance values saved for the current zeroing type (e.g., For firearm type A, when you select the option, only the distance values saved for type A will be available). Press and hold the rotary encoder (7) to save the changes and return to the home screen. In the shortcut menu, it will automatically save the changes and return to the home screen if there is no operation within 5s. MAIN MENU On the home screen, press and hold the rotary encoder (7) for 3s to enter the main menu interface. Rotate the rotary encoder (7) to switch between the function options in the main menu, rotate clockwise to move down and anticlockwise to move up. The function options in the main menu are cyclical:
when the cursor reaches the last option, continue rotating the rotary encoder (7) clockwise and the cursor will move to the first option. Press the rotary encoder (7) to modify the parameters of the current option or enter the submenu. The position of the cursor indicates the selected option, and the selected icon will change from white to blue.
- 24 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 25 -
The operation of secondary and tertiary menus is the same as above. In any menu interface, press and hold the rotary encoder (7) to save the changes and return to the upper menu interface. And, briefly press the power button (5) to return to the upper menu without saving. In the main menu interface, the device will automatically return to the home screen without any saving if there is no operation within 15s. During the continuous operation of the scope, when exiting from the main menu, the cursor remains at the position before exiting. When you restart the scope and enter the main menu for the first time, the selected option stays at the first menu option. Main Menu Features and Descriptions Wi-Fi-Turn the Wi-Fi function on/off Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Wi-Fi function option. Press the rotary encoder (7) to turn Wi-Fi function on/off. The icon in the status bar changes accordingly when Wi-Fi is turned on or off. Exposure Compensation-Set the exposure compensation Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Exposure Compensation option. Press the rotary encoder (7) to enter the submenu of Exposure Compensation. Rotate the rotary encoder (7) to select one exposure compensation level from -2.0 to +2.0. There are 13 levels of the exposure compensation, but only 5 levels are displayed on the screen when rotating the rotary encoder (7) each time. Press the rotary encoder (7) to confirm the selection, and return to the main menu. Zeroing Profile-Select Zeroing Profile Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Zeroing Profile option. Press the rotary encoder (7) to enter the submenu of the zeroing profile. Rotate the rotary encoder (7) to select one from the three zeroing profiles (A, B, C).
- 26 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 27 -
Press the rotary encoder (7) to confirm the selection, and return to the main menu. The name of the selected profile will change in the status bar. Zeroing Please set up the zeroing profile and zeroing distance before carrying out any zeroing operation. The Tube series supports any zeroing distance between 1 and 999 meters. Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Zeroing option. Press the rotary encoder (7) to enter the submenu of Zeroing, where displays 3 types of zeroing distance. Rotate the rotary encoder (7) to select the zeroing distance based on the preset target distance. Press the rotary encoder (7) to confirm the zeroing distance, and enter the zeroing distance submenu as follows. Zeroing If the default zeroing distance is consistent with the preset target distance, you can zero your device directly as follows. Select the Zeroing option and briefly press the rotary encoder (7) to enter the Zeroing interface. The X axis and Y axis coordinates of the reticle are displayed at the top left corner of the screen. Aim the reticle center at the target and shoot, and then observe the position of the actual point of impact. screen. If the impact point is not the same as the aim point, keep the aiming position still, and press and hold the Palette (6) + Camera (3) buttons at the same time to freeze the picture, and the freezing icon appears on the bottom center of the Rotate the rotary encoder (7) to move the image position, until the reticle center aims at the position of the point of impact. For details, refer to section Zeroing. Zeroing Distance Setting If the default zeroing distance is not consistent with the preset target distance, you can set the distance here. Select a non-primary distance and enter the submenu for operation with a brief press of the encoder (7). Rotate the rotary encoder (7) to select the option
"Setting the Zeroing Distance".
- 28 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 29 -
displayed on the top status bar. If off is selected, the standby function is disabled. Note
When the device is in the following status, the standby mode is activated automatically: up > 70 or down > 70, and left >30 or right > 30
When the device is in the shooting status (horizontally positioned), the standby mode is disabled. Settings This function is used to set the date, time, language, measurement unit, status auto hiding, factory reset, and device information query. Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Settings option. Press the rotary encoder (7) to enter the submenu of the settings. This menu item allows you to configure the following settings. Date-Setting the system date In the Settings submenu, rotate the rotary encoder (7) to select the Date option. Press the rotary encoder (7) briefly to activate the date reset function accompanied by two triangle Press the rotary encoder (7) to activate the zeroing distance reset function, and then two small triangle symbols are displayed above and below the number . Rotate the rotary encoder (7) to set the number value of the current position from 0 to 9. Press the rotary encoder (7) to switch among the positions of hundred, ten and one digits. After setting, press and hold the encoder (7) to save the setting and exit. The cursor returns to the zeroing option, and the zeroing distance changes accordingly. Besides, the status bar updates to the new zeroing distance synchronously. Standby-Set the standby status and time Press and hold the rotary encoder (7) to enter the main menu. Rotate the rotary encoder (7) to select the Standby option. Press the rotary encoder (7) briefly to enter the Standby submenu. Rotate the rotary encoder (7) to select one option from 10min, 20min, 30min and off. Press the rotary encoder (7) to confirm the selection, and then the selected option is Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated.
- 30 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 31 -
This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. icons appearing above and below the value. Date format is displayed as YY.MM.DD format. Rotate the rotary encoder (7) to set the correct year, month and date. Press the rotary encoder (7) to switch among year, month and date. After setting, press and hold the rotary encoder (7) to save changes and exit the date setting function. Time-Setting the system time In the Settings submenu, rotate the rotary encoder (7) to select the Date option. Time format is displayed as HH:MM in 24-hours format (14:48). Press the rotary encoder (7) briefly to activate the date reset function accompanied by two triangle icons appearing above and below the value. Rotate the rotary encoder (7) to set the correct hour and minute. Press the rotary encoder (7) to switch between the hour and minute. After setting, press and hold the rotary encoder
(7) to save changes and exit the time reset function. After setting time, the time in the status bar changes accordingly. Language-Selecting language In the Settings submenu, rotate the rotary encoder (7) to select the Language option. Press the rotary encoder (7) to enter the submenu for language selection. Rotate the rotary encoder (7) to switch among English and Russian. Press the rotary encoder (7) to confirm the selection and return to the upper menu. Units of Measure -Selecting the units of measure In the Settings submenu, rotate the rotary encoder (7) to select the Units of Measure option. Press the rotary encoder (7) to enter the submenu for unit setup. Rotate the rotary encoder (7) to switch between meter and yard. Press the rotary encoder (7) to confirm the selection and exit to the upper menu interface. Status Auto Hiding-Enabling/Disabling status auto hiding In the Settings submenu, rotate the rotary encoder (7) to select the Status Auto Hiding
- 32 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 33 -
Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. on the top of the display simultaneously with the main image. When the main image is enlarged by rotating the encoder (7), the image shown in the PIP window is also enlarged accordingly. For example, when the magnification of the main image is 4, the corresponding magnification of the PIP image is 8. option. Press the rotary encoder (7) to enter the submenu of the status auto hiding option. Rotate the rotary encoder (7) to select On or Off. Press the rotary encoder (7) to confirm the selection and return to the upper menu interface. Factory Reset-Reset to factory settings In the Settings submenu, rotate the rotary encoder (7) to select the Factory Reset option. Press the rotary encoder (7) to enter the submenu. Rotate the rotary encoder (7) to select "Yes" for restoring factory settings or "No" for canceling the operation. Press the rotary encoder (7) to confirm the selection. If "Yes" is selected, the scope will reboot automatically. If "No" is selected, the operation is canceled and return to the upper menu. After the Factory Reset is selected, the following functions will be restored to default settings:
- Image Mode: Day mode
- Zeroing Distance: A100m
- Optical Magnification: 4.0
- Standby: Off
- Wi-Fi: Off
- Language: English
- Unit of Measure: Meter
- Status Auto Hiding: Off Info-Show device information In the Settings submenu, rotate the rotary encoder (7) to select the Factory Reset option. The relevant information of scope will be shown by a short press of the rotary encoder (7). This item allows the user to view the following information about the scope: the product model, GUI version, SYS Info, Boot version, FPGA, PN and SN number of the riflescope, Hardware version and FCC ID. Press and hold the rotary encoder (7) to return to the upper menu interface. PIP FUNCTION Picture-in-Picture (PIP) provides a floating window independent of the main image. This window shows the image which is enlarged to 2 in a certain area centered on the reticle of the main image. On the home screen, press and hold the palette button (6) to switch the PIP function on/off. When the PIP is on, a separate 'window' is appeared
- 34 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 35 -
This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. Due to some factors, this function is not available for right will change accordingly. image. Three pre-defined target values are provided as on the top of the display simultaneously with the main When the main image is enlarged by rotating the encoder (7), the image shown in the PIP window is also enlarged accordingly. For example, when the magnification of the main image is 4, the corresponding magnification of the PIP image is 8. Note
some regions. STADIAMETRIC RANGEFINDER The Tube series provides stadiametric rangefinder, which allows you to calculate the approximate distance from a target with a known size. On the home screen, press and hold the brightness button (4) to turn the stadiametric rangefinder function on. When the function is on, two lines used for measuring appear in the middle part of the image, and three icons of pre-configured objects and the values of measurement distance are displayed on the right side. follows:
- Deer: 1.7m high
- Wild boar: 0.7m high
- Hare: 0.2m high the display area. Adjust the device to locate the target in the center of Rotate the rotary encoder (7) clockwise to enlarge or anticlockwise to reduce the width of the measure-
ment lines, so that the target is completely between the measurement lines. While adjusting the width of the measurement lines, the rangefinder values on the The color and center position of the measurement line are synchronized with the reticle. If you want to change the measurement unit, please go to Main Menu-Settings-Units of Measure for modification. Press and hold the brightness button (4) to exit the stadiametric rangefinder function. STATUS AUTO HIDING This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option.
- 36 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 37 -
Picture-in-Picture (PIP) provides a floating window independent of the main image. This window shows the image which is enlarged to 2 in a certain area centered on the reticle of the main image. On the home screen, press and hold the palette button (6) to switch the PIP function on/off. When the PIP is on, a separate 'window' is appeared Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. Wi-Fi The Tube series has a built-in Wi-Fi module. The device can connect wirelessly to a mobile device (laptop or smartphone) via Wi-Fi. To enable the wireless module, enter the main menu by long pressing the rotary encoder (7). Rotate the rotary encoder (7) to select the Wi-Fi option. Press the rotary encoder (7) briefly to turn on/off Wi-Fi module. After the Wi-Fi of the scope is enabled, search for the Wi-Fi signal with the name Infiray_XXXXXX on the mobile device, of which, XXXXXX is a 6-bit serial number composed of digits and letters. Select the Wi-Fi, enter the password and connect. The initial password is 12345678. When Wi-Fi is successfully connected, you can control the scope via the mobile app. Setting Wi-Fi name and password The Wi-Fi name and password of Tube series can be reset in the InfiRay Outdoor application. After connected with the mobile device, find and click the "Setting" icon in the InfiRay Outdoor to enter the setting interface. In the text box, enter and submit the new name
(SSID) and password of the Wi-Fi. It needs to reboot the device to take the new name and password effect. Note
After the device is restored to the factory settings, the name and password of the Wi-Fi will also be restored to the default factory default settings. UPDATE AND INFIRAY OUTDOOR The Tube series digital night vision scope supports InfiRay Outdoor technology, which allows you to transmit the image from the scope to the smartphone or tablet via Wi-Fi in real time mode. You can find detailed instructions on InfiRay Outdoor in the separate brochure at the site www.infirayoutdoor.com. The design of the scope provides the software update option. Updating is possible via the InfiRay Outdoor
- 38 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 39 -
application. Also, it is feasible to download and update software from the official website: www.infirayout-
door.com. About InfiRay Outdoor You can get InfiRay Outdoor application in the official website (www.infirayoutdoor.com), or search InfiRay Outdoor in App store to download App, or scan the following QR code to download. When installation completed, open InfiRay Outdoor application. If your device has been connected to a mobile device, enable mobile data on it. After the device accesses the Internet, an update prompt will be displayed automatically. Click Now to download the latest version immediately or click Later to update later. InfiRay Outdoor will automatically store the last connected device. So, if the scope has not connected with your mobile device, but linked to InfiRay Outdoor before, the update prompt will appear if there is an update when turning on InfiRay Outdoor. You can download the update first via mobile Wi-Fi and then connect the scope with mobile device to finish the update. After finishing the update, the device will root. This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. application. Also, it is feasible to download and update software from the official website: www.infirayout-
door.com. About InfiRay Outdoor You can get InfiRay Outdoor application in the official website (www.infirayoutdoor.com), or search InfiRay Outdoor in App store to download App, or scan the following QR code to download. When installation completed, open InfiRay Outdoor application. If your device has been connected to a mobile device, enable mobile data on it. After the device accesses the Internet, an update prompt will be displayed automatically. Click Now to download the latest version immediately or click Later to update later. InfiRay Outdoor will automatically store the last connected device. So, if the scope has not connected with your mobile device, but linked to InfiRay Outdoor before, the update prompt will appear if there is an update when turning on InfiRay Outdoor. You can download the update first via mobile Wi-Fi and then connect the scope with mobile device to finish the update. After finishing the update, the device will root. TECHNICAL INSPECTION It is recommended to carry out a technical inspection each time before using the scope. Check the following:
The scope appearance (there should be no cracks on The condition of the object lens and eyepiece (there should be no cracks, greasy spots, dirt or other the body). deposits). The status of the rechargeable battery (it should be fully charged in advance) and electrical contact (no salinization or oxidation). The electrical controls/buttons should be in working order. MAINTENANCE The maintenance should be carried out at least twice a year and includes the following steps:
Wipe the external surface of metal and plastic parts off dust with a cotton cloth. Silicone grease may be used for cleaning process. Clean the electric contacts and battery slots on the scope using a non-greasy organic solvent. Check the optics of the lens and the eyepiece. If necessary, remove the dirt and sand from the optics
(it is perfect to use a non-contact method). Cleaning of the exterior of the optics should be done with cleaners designed especially for this purpose.
- 40 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 41 -
The Tube series digital night vision scope supports InfiRay Outdoor technology, which allows you to transmit the image from the scope to the smartphone or tablet via Wi-Fi in real time mode. You can find detailed instructions on InfiRay Outdoor in the separate brochure at the site www.infirayoutdoor.com. The design of the scope provides the software update option. Updating is possible via the InfiRay Outdoor Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. TROUBLESHOOTING The following table lists all the problems that may occur when operating the scope. Carry out the recommended checks and troubleshooting steps in the order shown in the table. If there are defects that are not listed in the table or it is impossible to repair the defect yourself, return the scope to the vendor or supplier for repair service. Faults Possible Causes Solutions The battery is out of charge Charge the battery The USB cable is damaged Replace the USB cable The external power supply is insufficient The display brightness level is too low. The lens is not focused There is dust or condensate on the interior or exterior optical surfaces of the lens. If necessary, check the external power supply Adjust the display brightness Rotate the lens focus ring to adjust the focus Wipe off the outer optical surface by using a soft cotton cloth. Let the scope dry by leaving it in a warm environment for 4 hours. Check that the scope has been securely mounted. Make sure that the bullet type and caliber you use are The device cannot be started The device cannot be powered by an external power supply The Image is too dark. The GUI icons are clear but images are blurry Faults Possible Causes Solutions The position of the reticle moves after shooting The scope or the mount clamp is not fixed firmly. as consistent with that used for zeroing. If your scope was zeroed in summer but used in winter
(vice versa), the zeroing point may move slightly. Set the scope according to the section Operation. Check the outer surface of the objective lens and eyepiece, and if necessary, wipe off any dust and frost on it. In cold weather, a special antifogging coating can be applied (such as those used on eyeglasses or car rearview mirrors). Move the device to an area with no or fewer Wi-Fi signals. Move the device to a place where you can receive Wi-Fi signals. The scope cannot focus Configuration error The Wi-Fi password is incorrect Input the correct password The device cannot connect with the smartphone or tablet PC. Wi-Fi signals are lost or interrupted There are too many Wi-Fi signals around the device, which may cause interference. Smartphone or tablet is out of range of a strong Wi-Fi signal. Or there are obstacles between device and the smartphone or tablet
(such as concrete wall).
- 42 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 43-
Press the rotary encoder (7) to enter the submenu of Status Auto Hiding option and then select On or Off by rotating the rotary encoder (7). After the status auto hiding is enabled, all GUI icons including the status bar will be automatically hidden and only the image and reticle are displayed if there is The GUI information will be displayed again with the Only after the GUI is displayed, the button and menu no operation within 8s. press of any button. can be manipulated. This function is used to automatically hide the GUI information on the interface other than the reticle, so to make the image unobtrusive. Rotate the rotary encoder (7) to select Settings option in the main menu. Press the rotary encoder (7) to enter the Settings submenu, and rotate the rotary encoder (7) to select Status Auto Hiding option. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Body-worn Operation This device was tested for typical body-support LEGAL AND REGULATORY INFORMATION Wireless transmitter module frequency range:
WLAN: 2.412-2.472GHz (For EU) Wireless transmitter module power<20dBm (only for EU) IRay Technology Co., Ltd. thus declares that the Tube series digital night vision scope complies with the directives 2014/53/EU and 2011/65/EU. The full text of the EU declaration of conformity as well as additional information are available at:
www.infirayoutdoor.com. This device may be operated in all member states of the EU. FCC Statement FCC-ID: 2AYGT-TD5OL Labeling requirements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information to the user Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
- 44 -
InfiRay Outdoor Tube TD50L Operating Manual InfiRay Outdoor Tube TD50L Operating Manual
- 45 -
operations. To comply with RF exposure requirements, a minimum separation distance of 0cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. We, IRay Technology Co., Ltd., hereby declare that this product was tested conforming to the applicable FCC rules under the most accurate measurement standards possible, and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the Commissions requirements.
- 46 -
InfiRay Outdoor Tube TD50L Operating Manual
1 2 | label | ID Label/Location Info | 202.14 KiB | January 28 2022 |
a4 FCC ID:2AYGT-TD50L iu TENET TTT WUTC ee Lo Se a a ae CS}
TIF FP PRA a Cy Cae a a f Emer Tr Imam McA re ce eee eT I mi
1 2 | Agent Authorization | Cover Letter(s) | 96.75 KiB | January 28 2022 |
Letter of Authorization Company:
Address: 11GUIYANG STREET, YANTAI ECONOMY AND TECHNOLOGY IRay Techonlogy Co.,Ltd DEVELOPMENT DISTRICT, YANTAI SHANDONG P.R.CHINA Product Name: TUBE THERMAL IMAGING SCOPE Model Number: TD50L FCC Identifier: 2AYGT-TD50L We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Peng Zhang Title: Quality supervisor Signature of applicant:
Date: 2022/01/25
1 2 | FCC long Term Confidentiality | Cover Letter(s) | 92.72 KiB | January 28 2022 |
IRay Techonlogy Co.,Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2022/01/10 Subject; Request for Confidentiality FCC ID: 2AYGT-TD50L To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);
External Photos Test Setup Photos Internal Photos User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:
Name: :
Title: Quality supervisor Peng Zhang
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2022-01-28 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | JBP - Part 15 Class B Computing Device Peripheral |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2022-01-28
|
||||
1 2 | Applicant's complete, legal business name |
IRay Technology Co., Ltd.
|
||||
1 2 | FCC Registration Number (FRN) |
0030296552
|
||||
1 2 | Physical Address |
11GUIYANG STREET, YANTAI ECONOMY AND TECHNOLOGY DEVELOPMENT DISTRICT, YANTAI SHANDONG P.R.CHINA
|
||||
1 2 |
11GUIYANG STREET, YANTAI ECONOMY AND TECHNOLOGY
|
|||||
1 2 |
YANTAI, N/A
|
|||||
1 2 |
China
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
c******@micomlabs.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
1 2 |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
2AYGT
|
||||
1 2 | Equipment Product Code |
TD50L
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
P**** Z******
|
||||
1 2 | Telephone Number |
18562********
|
||||
1 2 | Fax Number |
0535-********
|
||||
1 2 |
p******@iraytek.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
IRay Techonlogy Co.,Ltd.
|
||||
1 2 | Physical Address |
China
|
||||
1 2 |
p******@iraytek.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | JBP - Part 15 Class B Computing Device Peripheral | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | TUBE THERMAL IMAGING SCOPE | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output power listed is conducted power. SAR compliance for body-worn operating configurations is limited to the specific configurations tested for this filing. Body-worn operations are restricted to belt-clips, holsters or similar accessories that have no metallic component in the assembly and must provide at least 0 cm separation between the device and the body of the user. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR for body-worn accessory use condition is 0.30W/kg. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
CCIC Southern Testing Co., Ltd
|
||||
1 2 | Name |
Z**** S********
|
||||
1 2 | Telephone Number |
86-07********
|
||||
1 2 |
z******@ccic-set.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC | 2412.00000000 | 2462.00000000 | 0.0490000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B | CC |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC