FCC ID: UFE-AXFY1 Sundial Radio Module module AXF-Y1

User Guidance for the Sundial Module model: AXF-Y1 FCC ID: UFE-AXFY1 IC: 6652A-AXFY1 1. Introduction Module Name: Sundial Module Model Number: AXF-Y1 The Sundial module model AXF-Y1 is a 2.4GHz Wi-Fi module which is compliant with IEEE 802.11b/g/n specifications. 2. Electrical 3. Environmental Chipset: The Sundial module main chipset: MediaTek MT7688 Supply: The module source all require power from 5VDC input supply Operating Temperature: The Sundial module operates across the temperate range of -10 to 55 Celsius 4. OEM/Integrators Installation Manual:

Important Notice to OEM Integrators 1. This module is limited to iRobot Corporation use ONLY. 2. Any modifications to the Sundial module model AXF-Y1 may invalidate regulatory approvals or may necessitate notifications to the relevant regulatory authorities. 3. OEM must inform iRobot Compliance of any changes which may require the Class I or Class II permissive changes for the FCC. 4. The Sundial Radio module model AXF-Y1 uses an internal PCB trace antenna. Any substituted antenna and RF cable assemblies must be tested and approved in order to maintain compliance to FCC and ISED rules. 5. For FCC Part 15.31(h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The module should be transmitting and the evaluation should confirm that the modules intentional emissions are compliant with the transmitter rules. End Product Labelling When the module is installed in the host device, the FCC/IC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. The label shall state to following:

Contains FCC ID: UFE-AXFY1 Contains IC: 6652A-AXFY1 The FCC ID and IC ID can be used only when all FCC/IC compliance requirements are met. Alternatively, electronic labelling method as documented in KDB 784748 may also be used. Antenna Installation and users, antenna, 1. The antenna must be installed such that 20cm is maintained between the antenna 2. The transmitter module may not be co-located with any other transmitter or 3. Only antennas of the same type and with equal or less gains as shown below may be used with this module. Other types of antenna and/or higher gain antennas will require additional authorization for operation. In the event that these conditions cannot be met, then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the host device. In these circumstances, the OEM integrator will be responsible for re-evaluating the host device (end-product), including the transmitter and obtaining a separate FCC/IC authorization. 5. Tested Antenna Information:

Antenna No. 1 (Internal) Brand Model Gain (dBi) Antenna Type iRobot AXF-Y1 4 PCB Internal Trace antenna Frequency Range

(GHz) 2.4-2.4835 6. Regulatory Information:

6.1 USA Federal Communication Commission (FCC) Information to the User:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by iRobot Corporation could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio interference to radio communications. However, there communication will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

is no guarantee that o Reorient or relocate the receiving antenna. o o Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. o Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This product complies with FCC 2.1091(b) for mobile device RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per FCC requirements, maintain a distance of more than 8 inches (20cm) between any person and the host device (Roomba robot). 6.2 Canada Innovation, Science and Economic Development (ISED) This device contains a licence-exempt transmitter/receiver that complies with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than the necessary for successful communication. ISED Statement on Radiation Exposure: This product is compliant with the Canadian Standard IC RSS-102, Restriction of RF Exposure in an Uncontrolled Environment. The device can be used safely for its intended purpose, as described in this manual. Per ISED requirements, maintain a distance of more than 8 inches (20cm) between any person and the Roomba robot. French Text:

Cet appareil respecte lalina 15 de la rglementation FCC. Lutilisation doit respecter les deux conditions suivantes :

(1) cet appareil ne doit pas provoquer dinterfrences nuisibles, et

(2) cet appareil doit tolrer toute interfrence reue, y compris les interfrences susceptibles dengendrer un fonctionnement indsirable. lalina 15 de la rglementation FCC ainsi qu Cet appareil est conforme aux normes dexemption de licence RSS dIndustry Canada. Lutilisation doit respecter les deux conditions suivantes : (1) cet appareil ne doit pas provoquer dinterfrences, et (2) cet appareil doit tolrer toute interfrence, y compris les interfrences susceptibles dengendrer un fonctionnement indsirable de lappareil. Les changements ou modifications non approuvs expressment par iRobot Corporation sont susceptibles dentraner la rvocation de lautorisation dutilisation de lappareil. Cet quipement a t test et dclar conforme aux limites dun dispositif numrique de classe B, conformment la rglementation ICES-003. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut provoquer des interfrences nuisibles aux communications radio. Il nexiste toutefois aucune garantie que de telles interfrences ne se produiront pas dans une installation particulire. Si ce matriel occasionne des interfrences nuisibles aux rceptions radio ou tlvisuelle, ce qui peut tre dtermin en allumant et en teignant lappareil, lutilisateur est invit corriger ce problme en prenant une ou plusieurs des mesures suivantes :

o Rorienter ou repositionner lantenne de rception. o Augmenter lespacement entre lquipement et le rcepteur. o Brancher lappareil sur un circuit diffrent de celui du rcepteur. o Consulter le fournisseur ou un technicien radio/TV expriment afin dobtenir une assistance. Conformment la rglementation dIndustry Canada, cet metteur radio peut fonctionner uniquement avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industry Canada. Dans le but de rduire les risques de brouillage radiolectrique auprs des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas ltablissement dune communication satisfaisante. Dclaration de la FCC sur lexposition aux radiations : Ce produit est compatible avec lalina 2.1093(b) de la rglementation FCC, relatif la restriction de lexposition aux RF dans un environnement non contrl. Lappareil peut tre utilis en toute scurit pour lusage auquel il est destin, comme il est dcrit dans ce manuel. lintensit ncessaire Dclaration de la ISED sur lexposition aux radiations : Ce produit est compatible avec la norme canadienne IC RSS-102, relative la restriction de lexposition aux RF dans un environnement non contrl. Lappareil peut tre utilis en toute scurit pour lusage auquel il est destin, comme il est dcrit dans ce manuel. Conformment aux exigences ISED, maintenez une distance de plus de 20 cm (8 pouces) entre toute personne et le robot Roomba.

Current Revision Change Description:

Initial Release ECN:

N/A Date:

2019-10-17 Sundial Model: AXF-Y1 Made in China Manufacturer : Jabil Circuit

(Guangzhou)., Ltd. East District 190, Economica & Technological Dev, Des. 388 Lian Yun Road, 510530 Guangdong, China P.R.China CNC ID: XXXXXXX FCC ID: UFE-AXFY1 IC: 6652A-AXFY1 IFETEL: XXXXXXX ANATEL: XXXXXXX CMIIT ID: XXXXXXX CIDFXXXXXXXX NCCXXXXXXXXXXX XXXXXXX XXXXXXX 4 2 m m Applicant : iRobot Corporation Brand: iRobot 24mm Label, Compliance, Sundial Deb Keefe 4702373 A 2019-10-17

EXHIBIT H LABEL FORMAT Serial Number COMPANY NAME Model name:

US:AAAEQ##TXXX Complies with 47 CFR Part 68 USOC jack:

Made in Where:

US: Is a fixed field that indicates the equipment meets all requirements of 47 CFR Part 68

(including the requirements published by ACTA). AAA Is the responsible partys Grantee Code obtained previously from the FCCs Common Carrier Bureau or currently from ACTA. EQ Is an Equipment Code indicating to the Service Provider any special signal handling or billing requirements. The Equipment codes are listed in Annex A (normative).

## Is the Ringer Equivalence Number without a decimal point (e.g. REN of 1.0 = 10, REN of 0.3 = 03). In the case of a Z ringer, ZZ shall appear. In the case of approved equipment without a network interface and equipment not connecting to circuits with analog ringing supplied then NA shall appear. T Is the ringer type letter associated with the Ringer Equivalence Number, in accordance with the technical requirements. In the case of approved equipment without a network interface and equipment not connecting to circuits with analog ringing supplied, the letter N shall appear. XXX Is a product identifier, unique when combined with the responsible partys Grantee Code, of at least one and up to nine alphanumeric characters (including one or more dashes

(-) if desired. A dash shall not appear as the first or last character nor shall the identifier consist entirely of dashes). The responsible party shall define this identifier. I certify that above will be the format of the Label, which will be permanently attached and prominently displayed on all units of this Part 68 Compliance product. Authorized Signatory:

Signature

swtobol Federal Communications Commission 445 12th Street SW Washington, DC 20554 Subject: Class II Permissive Change iRobot Corporation FCC ID: UFE-AFXY1 May 6, 2022 To Whom It May Concern:

This application is intended to remove the collocation restriction from iRobot Corporation Radio Module with FCC ID: UFE-AXFY1. Further details and supporting documents are attached. Should you have any questions, please feel free to contact the undersigned. Sincerely, phe allotta, NCE INARTE Certified Product Safety and EMC Engineer Sr. Principal Compliance Engineer iRobot Corporation 8 Crosby Drive Bedford, MA 01730 Phone: 1 781-430-3284 Email: spallotta@irobot.com

@ iRobot.com iRobot Corporation | 8 Crosby Drive, Bedford MA 01730 | 781.430.3000

Confidentiality Request regarding application for certification of FCC ID: UFE-

AXFY1 April 28, 2022 Attention:ApplicationExaminer RE:

RequestforConfidentiality Applicant:iRobotCorporation FCCID:UFEAXFY1 ToWhomItMayConcern:

PermanentConfidentiality RequestisherebysubmittedbyiRobotCorporationtowithholdpermanentlyfrompublicreview certainportionsoftheapplicationforequipmentcertificationforthereferencedFCCidentifiers. Thisrequestforconfidentialityismadepursuantto47CFR0.457(d)and0.459oftheFCCRules. Inparticular,thefollowingsectionsoftheapplicationaretobekeptpermanentlyconfidential:

Schematics DetailedBlockDiagrams DetailedOperational/FunctionalDescription ShorttermConfidentiality RequestisherebysubmittedbyiRobotCorporationtowithholdfrompublicreviewforaperiod of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certainportionsoftheapplicationforequipmentcertificationforthereferencedFCCidentifiers. Thisrequestforconfidentialityismadepursuantto47CFR0.457(d)and0.459oftheFCCRules. Inparticular,thefollowingsectionsoftheapplicationaretobekeptconfidentialforaperiodof 180daysfromthedateofAuthorization:

Internalphotos Rationaleforrequestforconfidentiality:

iRobotCorporationhasinvestedconsiderabletimeandmaterialsinresearchanddevelopment toproducethereferencedproduct. Permanentconfidentiality:Disclosureofthepermanentlyconfidentialportionsofthisapplication tocompetitorswouldnotonlygivethemsignificantcompetitiveadvantagesindevelopingsimilar iRobot.com iRobot Corporation | 8 Crosby Drive, Bedford MA 01730 | 781.430.3000

wobot Letter of Agency April 28, 2022 Federal Communications Commission 445 12'" Street SW Washington, DC 20554 Subject: Limited Agency Agreement iRobot Corporation FCC ID: UFE-AXFY1 To Whom It May Concern:

We, iRobot Corporation, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number UFE-AXFY1 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is April 28, 2022. The Limited Agency Agreement expires on December 31, 2022 unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Stephen Pallotta, NCE iNARTE Certified Product Safety and EMC Engineer Sr. Principal Compliance Engineer iRobot Corporation 8 Crosby Drive Bedford, MA 01730 Desk phone: +1 781-430-3284 Email: spallotta@irobot.com

) iRobot.com iRobot Corporation {| 8 Crosby Drive, Bedford MA 01730 | 781.430.3000

(vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in equipment the authorization. application for

(viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. A sample of the host label is provided as an exhibit, showing the FCC identifier of the module. The module complies fully with the operating requirements of Part 15 section Subpart B; Subpart C section 15.247 and Part 2 section 2.1091] as demonstrated in the test report exhibits. The module complies fully with the operating requirements of FCC Rules Part 2 section 2.1091 and section Part 15 section 15.247(i) as demonstrated in the test report exhibit. iRobot.com iRobot Corporation | 8 Crosby Drive, Bedford MA 01730 | 781.430.3000