FCC ID: SK9NIC NIC Router Module

NIC Router Module Technical Reference Guide Effective Date: February, 2020 NIC Module Revision History A The following table describes the changes to this document for each revision of the NIC router module:

Revision Date Description of Change February, 2020 Initial Release NIC Module Labeling The following requirements will be applied to any products that use this module:

The end product or host label will include the following text:

Contains:

FCC ID: SK9NIC IC: 864G-NIC, Model: NIC The users manual for any product that contains this module will contain the following text. If the device is large enough, then this will also be placed on the label. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Regulatory Compliance The users manual for any product that contains this module will contain the following text:

Module Compliance FCC/ISED This module has been tested and found to comply with the following requirements for Modular Approval. Part 15.247 - Operation within the bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. RSS-247 - Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and License-Exempt Local Area Network (LE-LAN) Devices FCC Part 15, Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Additional testing, Part 15 Subpart B disclaimer The Itron NIC modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. NIC Module Changes or modifications to this device not expressly approved by Itron, Inc. could void the users authority to operate the equipment. Innovation, Science and Economic Development Canada (ISED) This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numrique de la classe B rpond la norme Canadienne sur le matriel brouilleur. L'opration est sujette aux deux conditions suivantes: (1) ce dispositif ne peut pas causer d'interfrence nocive, et (2) ce dispositif doit accepter n'importe quelle interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science and Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. RF Exposure (FCC/ISED) The users manual for any product that contains this module will contain the following text:

This equipment complies with radiation exposure limits set forth as a mobile classification for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux radiations dans un environnement non contrl. Cet quipement do it tre install et utilis distance minimum de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-localises ou oprant en conjonction avec tout autre antenne ou transmetteur. Miscellaneous The users manual for any product that contains this module will contain the following text:

Professional Installation This module is intended for professional installation by the integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. NIC Module Antennas The following external antenna types have been approved for use with the Itron NIC module. Monopole, 3dBi gain, (Laird, P/N: TRA9023P) Monopole, 2.8dBi gain, (Cisco, P/N: ANT-MP-INT-OUT-M) Inverted F (PCB), 2.04dBi gain, (Taoglas) For situations where the host manufacturer is responsible for an external connector, the integration instructions shall inform the installer that a unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. Modification and Repairs To ensure FCC compliance and system performance, this device, antenna and/or coaxial assembly shall not be changed or modified without the express written approval of Itron. Any unauthorized modification will void the users authority to operate the equipment. WARNING! This device contains no user serviceable parts. Attempts to repair this device by unauthorized personnel may subject the person to shock hazard if removal of protective covers is attempted. Unauthorized repair will void the warranty and/or maintenance contract with your company. Operational Description The Itron NIC is a communications module which utilizes a 902.4 MHz to 927.8 MHz transmitter. This module operates within a host unit which is part of a utility network system designed to communicate with other devices in this network such as electricity meters and routers. The module operates on DC voltage which is supplied by the host device. Test Modes Itron uses various test mode programs for test set up which operate separate from production firmware. Host integrators should contact Itron for assistance with test modes needed for module/host compliance test requirements. Recycling Information The product you have purchased contains circuit boards. At the end of the modules useful life, under various state and local laws, it may be illegal to dispose of certain components into the municipal waste system. Check with your local solid waste officials for details about recycling options or proper disposal. About this Manual This technical reference guide describes the installation of the NIC module for the Itron Socket Based Router. NIC Module Installation The NIC module will be installed in the Itron Socket Based Router (SBR). Install the NIC module by plugging the module into the PCI slot. NIC Module Install the shield that covers the NIC module with only RF QMA connect exposed. NIC Module Plug in the covered module in to SBR and connect the cables:

NIC Module Electronics assembly (with NIC) installed in SBR host. NIC Module

Applicants Company Letterhead Date: 05-10-2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: (SK9NIC) Dear Sir or Madam, Itron, Inc. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. If you have any questions, please contact us. Sincerely, Contact name: Christopher OSteen Company name: Itron, Inc. Address: 313 SC-11 B, West Union, SC 29696 E-mail: Christopher.OSteen@itron.com Tel: (919) 744-8478

Applicants Company Letterhead To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-10-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: (SK9NIC) Itron, Inc. (the applicant) certifies that, as of the date of the filing of the application, Itron, Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Itron, Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Christopher OSteen (Itron, Inc.) accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: Itron, Inc. Address: 313 SC-11 B, West Union, SC 29696 Contact Person: Christopher OSteen Tel.: (919) 744-8478 Email: Christopher.OSteen@itron.com FRN: 0006329973 Sincerely, Rev 1/26/2023

May 10, 2023 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

I hereby appoint Kirby Munroe at TUV SUD America to act as our agent in the preparation of an application for equipment authorization of FCC ID: SK9NIC to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Signature:

Name: Christopher O'Steen Title: Senior Design Assurance Engineer

TUV SUD America, 5945 Cabot Parkway, Suite 100, Alpharetta GA 30005 Date: April 11, 2023 Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: FCC ID: SK9NIC To Whom It May Concern:

The following application is submitted on behalf of our client, Itron Inc., for evaluation of their model NIC for a C2PC certification under FCC Part 15.247. The C2PC is to add new modes to the DSS/DTS radios I have reviewed the application and supporting documentation and have found them to comply with FCC requirements. I recommend this application for certification. Yours sincerely Kirby Munroe, Wireless EMC Technical and Certification Manager Document: 120780 v1 Page 1 of 1

Federal Communications Commission Date: March 6, 2020 Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

Itron, Inc. respectfully requests confidentiality of certain materials provided with the submission of the under FCC ID: SK9NIC in accordance with 47 CFR 0.457(d) and 47 CFR 0.459. The confidentiality request applies to the following exhibits:

72157802 Block Diagram.pdf 72157802 Theory of Operation The NIC has been developed at considerable effort and expense by Itron, Inc. These items are considered as trade secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the companys business advantage. I appreciate your assistance in this matter. Sincerely, Lee Littlejohn Regulatory Engineer

March 06, 2020 TV SD UCB 5945 Cabot Parkway Alpharetta, GA 30005 Re: FCC ID: SK9NIC To Whom It May Concern:

The following application is submitted on behalf of our client, Itron Inc., for evaluation of their model NIC for a class II permissive change certification under FCC Part 15.247. The NIC communications module is built on Itrons IPv6 OpenWay platform.The module utilizes the 900 MHz radio frequency (RF) operation band. For this application the OFDM 1.2 Mbps data rate is being added. The purpose of this Class II Permissive Change is to add the DTS mode of the NIC module for installation in the new antenna/host combination. For this Class II Permissive Change, the NIC was integrated into the Itron, Inc. Socket Based Router (SBR) host. The new 900 MHz antenna is a internal PCB inverted F antenna terminated at 50 ohms. Other transmitters that are associated with the SBR host include a cellular modem

(FCC ID: N7NEM7455), a second 900 MHz transmitter (FCC ID: SK9ITR9002), Wi-Fi (FCC ID: SK9WF111) and a Zigbee transmitter (FCC ID: SK9ITR24). The Zigbee is not located in the SBR but in the 2S electricity meter that the SBR can be attached to. Radiated inter-modulation testing was performed for all combinations of simultaneous transmission and found to comply. The NIC was tested in full to the requirements of the aforementioned rules and was found to be in compliance. Sincerely, Signature:

Name: Lee Littlejohn Title: Regulatory Engineer MarcMarch