MODEL : LK-P11B MOBILE PRINTER All specifications are subject to change without notice RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTURECITONS Table of Contents 1. Product overview 2. Unpacking 3. Installation & Usage 3-1. Battery Installation 3-2. Battery Charging 3-3. Battery Charger Usage 3-4. Belt Strap Usage 3-5. Separation of Battery from the printer 3-6. Shoulder Strap Usage 3-7. Leather case Usage 3-8. Loading the paper 3-9. Control Panel Usage 3-10. Self Test 4. Peripherals Connection 4-1. Bluetooth Connection 4-2. Interface Cable Connection 5. Printer Cleaning 6. Product Specication 6-1. Specication 3 4 5 5 6 7 8 9 10 11 12 13 14 16 16 17 18 19 19 1. Product overview Power switch Paper feed button USB SERIAL Cover open button CHARGER CONNECTOR Battery 2 3 2. Unpacking Standard 3. Setting Up the Product 3-1. Installing battery Printer Battery Belt Buckle Recharger USB Shelded Cable Serial Cable Push the Open to the direction as pointed by arrow in the image. Open the battery cover and push up the hook to the direction as above. 1 2 3 Roll paper Option CD Quick Manual Printer case shoulder strap 4 Insert the battery inside printer as shown. Close the battery cover once you inserted the battery completely. Notes: As the battery is not charged at the time of your purchase, charge the battery prior to using the product.
(Use the battery charger and/or the optional battery holder.) 5 3-2. Battery Charging 3-3. Battery charger Usage 1. The battery can be charged only when the temperature is 0~40 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. Notes:
1. Do not turn on the printer power while you are charging the battery. 2. Do not print while charging the battery 3. Do not connect the charger to the printer on the process of printing. 1. Please press the battery into the holder until you can hear a snapping sound . 2. Insert DC JACK into the end completely as the direct shown above. 3. Plug the power code to electrical outlet. 4. While charging the battery, red light turns on. Once the charge is completed, green light turns on. Check the state of code connection when error occurs blinking on red light. 6 7 3-4. Belt Hook Usage 3-5. Removing battery Insert the belt hook screw into the hole of the belt hook. 1 2 Push the Open into the direction indicated with the arrow in the image. Push up the hook after opening the battery cover. 1 2 3 As shown above, fasten the screw with a screw driver. Pull out the battery as shown above. 8 9 3-6. Shoulder Strap Usage 3-7. Leather Case Usage Insert the strap into the hook on the printer. Place the end of strap into the hook of shoulder strap. 1 2 3 4 Open the Velcro Put the printer into the leather case following the direction shown in the 1 2 3 After pulling out the end of strap tightly, put it into the clip to be fastened. Fasten the strap in the opposite side with the sample way. 10 Close the Velcro 11 3-8. Loading the media. 3-9. Control Panel Press the cover open button and open Place the paper roll as shown. Make sure the paper is placed in right direction. 1 2 3 4 Button Name function This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to 3-10 for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. If the red light is turned on, it means that the paper cover is open. Power button Paper Feed Button Battery Status Lamp Error Lamp Pull a short length of paper out of the printer and close the cover. Press Feed button and let the paper be arranged property for printing. 12 13 3-10. Self Test You can check the printer setting state by doing self test when you set the printer rst time or encounter some problems.
- Control Circuit, Mechanisms, Print Quality, Rom version. When you can not nd the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software. Self Test Instructions 1.Turn the printer power off an close the printer paper cover. 2. While pressing the paper feed button, turn on the printer power. 3. The printout is producing 4. To add a printout of the Hex-Dump mode, press the paper feed button once more.
< Sample Printout of Self Test >
14 15 4. Peripherals Connection This product can communicate with other devises via Bluetooth communication and cable. 4-1.Bluetooth Connection 4-2. Interface Cable Connection 1. The printer can be connected to devices equipped with Bluetooth communication capacity (PDA, PC, etc.) 2. Use the Bluetooth connection function supported by the device to connect to the printer. USB Serial 1. Connect the interface cable to the cable connector of the printer Notes: Use only cables provided by this manufacturer 2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc) 16 17 5. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3. When cleaning the print head, take care not to touch the heated portion of the print head. The print head subject to be damaged by static electricity. 4. Take care not to allow the print head to become scratched and /or damaged in 1. Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts. 2. Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover. 6. Pritner Specication 6-1. Specication Printing Method Printing Speed Resolution Character Barcode Emulation Driver Sensor Paper Direct Thermal 80mm/sec 203 DPI X 203 DPI ALPHA NUMERIC Character, Extension Character Code 39, Code 93, UCC/EAN-128, Code 128, UPC-E, UPC-A, EAN-8, EAN-13, EAN-14, UPC and EAN 2 or 5 digit extensions, Plessey, FIM, Postnet, Interleaved 2-of-5, MSI, Codabar CPCL Window CE 4.2&5.0, Window Mobile 5.0 Black-mark, Gap, cover open paper type width thickness Thermal Paper 58mm 65 External Diameter Max. 56mm Internal Diameter 12.5mm +/-0.5mm Reliability TPH 100km Communications standard Serial(RS-232C), USB, Bluetooth Class2 option Wireless Lan *802.11b/g Battery Charger input AC100~240V, 50/6 Hz output 8.4V , 1200 mA Battery Charger Battery type Li-on output 7.2V, 2400mAh Charging time 2 Time Size WXDXH(mm) 104 X 74 X 154 WXDXH 4.0 X 2.9 X 6.0 Weight 500g 18 19 SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.0