MODEL : LK-P21B MOBILE PRINTER All specifications are subject to change without notice Table of Contents 1. Product overview 2. Unpacking 3. Usage and Installation 3-1. Control panel usage 3-2. Battery Installation 3-3. Battery removal 3-4. Battery charging 3-5. Battery charger usage 3-6. Usage of Cigar Jack for charging 3-7. Belt clip usage 3-8. Roll paper installation 3-9. Leather case usage 3-10. Self test 3-11. MSR usage 4. Peripherals connection 4-1. Bluetooth connectiontion 4-2. Interface cable connection 5. Printer specification 5-1. Specification 3 4 5 5 6 7 8 9 10 12 13 14 15 16 17 17 18 19 19 1. Unpacking Standard Printer Battery Belt Buckle Charger USB Cable Shielded Serial Cable Roll paper CD Quick Manual Option Battery Holder (Cradle) Cigar Jack Leather case Shoulder strip 2 3 2. Product overview 3. Usage and Installation 3-1 Control panel usage Paper feed button Power switch Belt clip hole DC Power Open Button USB SERIAL Battery Button Name function This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to 3-10 for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. If the red light is turned on, it means there is no paper roll or the paper cover is open. Power button Paper Feed Button Battery Status Lamp Error Lamp 4 5 3-2 Battery Installation 3-3 Battery removal Hook 180 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not charged at the time of your purchase, charge the battery prior to using the printer
(Battery charger or Cradle can be used to charge) Put up the Belt clip hole turning 180 degree. 1 2 6 7 After putting up the belt clip, remove the battery holding it up as shown above. 3-4 Battery charging 3-5 Battery charger usage 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. NOTE 1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before removing the battery, make sure that power is turned off. 3. Printer does not work in the status of being connected with charger only. 4. The battery should be installed to operate printer. 5. While charging, do not turn on the power. 6. Do not operate the print while charging the battery. 7. Do not connect the charger while the printer is operated. lamp 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. 3. Once the charging is completed, remove the battery from the holder. 3-5-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green NOTE In the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery. 8 9 3-6 Usage of Cigar Jack for charging 3-7 Belt Clip usage Printer Insert the belt clip screw into the hole of Belt clip 1 2 Battery holder Connect the car cigar JACK charger into the printer or battery holder. As shown in the picture, tighten the screw with a screw driver. 10 11 3-8 Roll Paper installation 3-9 Leather case usage Press the PUSH button to open paper cover Insert the paper in the right direction Open the leather case Place the printer into the leather case 1 2 3 4 1 2 3 4 Pull a short length of paper out of the printer and close the cover. Tear off the additional paper using tear bar. Close the Velcro and stick the cover. Fasten to the belt by using the clip at the rear of the leather case 12 13 3-10 Self Test
<The sample of self test printout>
Turn off the power pressing the power button for approximately 2 minutes. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds. The printout is produced. 14 When the printer is installed initially or when you face a problem, you can run the self test and check the information about
-Control Circuit, Mechanism, Print Quality, ROM Version After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. Motor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meter 15 3-11 MSR usage 4. Peripherals connection This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection Insert and swipe the card in the direction of the arrow as shown in the picture. 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected. 16 17 4-1 Bluetooth Connection 5. Pritner Specification 5-1 Specification USB Serial 1. Connect USB or Serial cable into the cable connector on the printer. NOTE Use the cable offered by the manufacturer (USB, Serial) 2. Connect the interface cable into the USB or Serial port of the device
(PDA, PC, etc.) Printing Method Printing Speed Resolution Character Character per line Character set Barcode Emulation Driver Sensor Paper Direct Thermal 80mm/sec 203 DPI X 203 DPI Font A (12X24), Font B (9X17) Font A : 32 columns , Font B : 42 columns ALPHA NUMERIC Charactor, Extension grapic EAN-8, EAN-13, Code39, ITF, UPC-A, Codabar, Code93, Code128 ESC/POS Window CE 4.2 & 5.0, Window Mobile 5.0 Paper End Sensor , Cover open Sensor paper type width thickness Thermal Paper 58mm 65 External Diameter Max. 40mm Internal Diameter 12.5mm +/-0.5mm Reliability TPH Battery 50km Continuous printing operation: 1hr and 30min Standby: 24hrs Printing length: 162m Communications Serial(RS-232C), USB, Bluetooth Class2 MSR (Optional) Card Standard ISO7811/2, JIS Track 1Track, 2Track, 3Track, JIS-II Magnet Head Life 300,000 Passes(minimum) 18 19 Battery Charger input AC100~240V, 50/60 Hz output 8.4V , 800~1200mA Battery Charger Battery type Li-on output 7.4V, 1130mAh Charging time 2 Time Size W X D X H(mm) 96 X 136 X 58 W X D X H 3.7 X 5.3 X 2.2 Weight Temperature operation Humidity storage operation 0.4kg 5 ~ 40
-10 ~ 50 35 ~ 95%
20 21
This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instuctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help.
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.0