MODEL : LK-P30B MOBILE PRINTER All specifications are subject to change without notice Table of Contents 1. Product overview 2. Unpacking 3. Usage and Installation 3-1. Control panel usage 3-2. Battery Installation 3-3. Battery removal 3-4. Battery charging 3-5. Battery charger usage 3-6. Belt clip usage 3-7. Roll paper installation 3-8. Leather case usage 3-9. Self test 3-10. MSR usage 3-11. IC CARD usage 4. Peripherals connection 4-1. Bluetooth connectiontion 4-2. Interface cable connection 5. Printer specification 5-1. Specification 6. CPCL Command Compatibility 7. Setting up the software 3 4 5 5 6 7 8 9 10 11 12 13 15 16 17 17 18 19 19 21 24 1. Unpacking Standard Printer Battery Belt Buckle Charger USB Cable Shielded Serial Cable Roll paper CD Quick Manual Option Battery Holder (Cradle) Leather case Shoulder strip 2 3 2. Product overview 3. Usage and Installation 3-1 Control panel usage Power switch Control Panel Paper feed button Battery Belt clip hole Open Button DC Power SERIAL USB Button Name function This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to 3-10 for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. If the red light is turned on, it means there is no paper roll or the paper cover is open. Power button Paper Feed Button Battery Status Lamp Error Lamp 4 5 3-2 Battery Installation 3-3 Battery removal 180 Put up the Belt clip hole turning 180 degree. 1 2 Hook 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not charged at the time of your purchase, charge the battery prior to using the printer
(Battery charger or Cradle can be used to charge) CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions 6 7 After putting up the belt clip, remove the battery holding it up as shown above. 3-4 Battery charging 3-5 Battery charger usage Optional lamp DC Jack 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. NOTE 1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before removing the battery, make sure that power is turned off. 3. Printer does not work in the status of being connected with charger only. 4. The battery should be installed to operate printer. 5. While charging, do not turn on the power. 6. Do not operate the print while charging the battery. 7. Do not connect the charger while the printer is operated. 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. 3. Plug the power code into the electrical outlet. 4. Once the charging is completed, remove the battery from the holder. 3-5-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green NOTE In the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery. 8 9 3-6 Belt Clip usage 3-7 Roll Paper installation Insert the belt clip screw into the hole of Belt clip 1 2 Press the PUSH button to open the paper cover Insert the paper in the right direction 1 2 3 4 As shown in the picture, tighten the screw with a screw driver. Pull a short length of paper out of the printer and close the cover. Tear off the additional paper using tear bar. 10 11 3-8 Leather case usage Optional 3-9 Self Test Open the leather case Place the printer into the leather case 1 2 3 4 Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds. Close the Velcro and stick the cover. Fasten to the belt by using the clip at the rear of the leather case The printout is produced. 12 13
<The sample of self test printout>
3-10 MSR usage Optional Insert and swipe the card in the direction of the arrow as shown in the picture. When the printer is installed initially or when you face a problem, you can run the self test and check the information about
-Control Circuit, Mechanism, Print Quality, ROM Version After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. Motor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meter 14 15 3-11 IC CARD usage Optional 4. Peripherals connection This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection Insert the card in the direction of the arrow as shown in the picture. 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected. 16 17 4-2 Interface Cable Connection 5. Pritner Specification 5-1 Specification Serial USB 1. Connect USB or Serial cable into the cable connector on the printer. NOTE Use the cable offered by the manufacturer (USB, Serial) 2. Connect the interface cable into the USB or Serial port of the device
(PDA, PC, etc.) Printing Method Printing Speed Resolution Character Character per line Character set Barcode Emulation Driver Sensor Paper Direct Thermal 100mm/sec 203 DPI X 203 DPI Font A (12X24), Font B (9X17) Font A : 48pt , Font B : 64pt ALPHA NUMERIC Character, Extension Character EAN-8, EAN-13, Code39, ITF, UPC-A,UPC-E, Codabar, Code93, Code128, PDF417(2D), MAXICode (2D) ESC/POS, CPCL, Commanl Compatible Window CE 4.2&5.0, Window Mobile 5.0 Paper End Sensor , Gap Sensor , Cover Open Sensor , Black Mark Sensor paper type width thickness Thermal Paper 25.4mm~79mm 0.06mm ~ 0.09mm External Diameter Max. 56mm Internal Diameter 12.5mm +/-0.5mm Reliability TPH Battery 50km Continuous printing operation: 1hr and 30min Standby: 24hrs Printing length: 162m Communications Serial(RS-232C), USB, Bluetooth Class2 MSR (Optional) Card Standard ISO7811/2, JIS Track 1Track, 2Track, 3Track, JIS-II Magnet Head Life 300,000 Passes(minimum) 18 19 IC CARD (Optional) EMV level one certified smart card reader TM Battery Charger input AC100~240V, 50/60 Hz output 8.4V , 800~1200mA Battery Charger Battery type Li-ion output 7.4V, 2200mAh Charging time 2-and-a-half hour Size W X D X H(mm) 120 X 152 X 70 W X D X H 4.7 X 5.9 X 2.7 Weight Temperature operation Humidity storage operation 0.6kg
-10 ~ 50
-20 ~ 60 35 ~ 95%
6. CPCL Command Compatibility NOTE Compatible Compatible with only commanders provided by the manufacturer. Partially Compatible Not Compatible x Printer Commands PRINT FORM JOURNAL UNITS Comments TEXT TEXT FONT-GROUP(FG) TEXT CONCATENATION MULTILINE(ML) COUNT SETMAG SCALABLE TEXT Linear Bar Codes BARCODE BARCODE-TEXT Two-Dimensional Bar Codes PDF417 (PORTABLE DATA FILE) MAXICODE QRCODE DATAMATRIX GS1(RSS) Compatibility Compatibility X Compatibility Compatibility 20 21 Line Print Mode SETLP SETLF Moving With X and Y Coordinates LMARGIN SETBOLD SETSP Special ASCII Characters SETFF SET-TOF SETLP-TIMEOUT Compatibility Graphics BOX LINE INVERSE-LINE PATTERN GRAPHICS PCX Advanced Commands CONTRAST TONE JUSTIFICATION PAGE-WIDTH PACE NO-PACE WAIT REWIND TENSION SPEED SETSP ON-OUT-OF-PAPER ON-FEED PREFEED POSTFEED PRESENT-AT COUNTRY/CODE PAGE FORMAT FILES BEEP CUT PATIAL-CUT MCR Compatibility Compatibility X X X X X X 22 23 CAUTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. 7. Setting up the software Please refer to the programming manual included in CD. Certification FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instuctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. 24 25 SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.0