FCC ID: UTWXT40WA Mobile Computer

www.janam.com 031319XT40 XT40 Series Quick Start Guide Technology at Work. Copyright 2019 Janam Technologies LLC. All rights reserved. Quick Start Guide seireS 04TX XT40 Series, Janam and the Janam logo are trademarks of Janam Technologies LLC. Other product and brand names may be trademarks or registered trademarks of their respective owners. Janam Technologies LLC assumes no responsibility for any damage or loss resulting from the use of this guide. Janam Technologies LLC assumes no responsibility for any loss or claims by third parties which may arise through the use of this product. Janam Technologies LLC assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery or repairs. To protect against data loss, be sure to make backup copies (on other media) of all important data. Follow all usage, charging and maintenance guidelines in the Product User Guide. If you have questions, contact Janam. For a copy of the Product User Guide, visit www.janam.com. Important: Please read the End User License Agreement for this product before using the device or the accompanying software program(s). Using the device or any part of the software indicates that you accept the terms of the End User License Agreement. Page 1 Janam Technologies LLC Battery Warning Content and Additional Resources CAUTION IF MISUSED OR MISTREATED THE BATTERY MAY PRESENT A RISK OF FIRE OR CHEMICAL BURN. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. BATTERY SAFETY GUIDELINES. Use only Janam XT40 Series batteries and recharge batteries using only Janam approved charging accessories. Observe the following guidelines for safe use of Li-Ion batteries:

1. Do not expose the battery to excessive heat or cold. Do not short-circuit. Do not incinerate. 2. To avoid risk of 3. Do not disassemble the battery. There are no user serviceable parts inside. 4. 5. If battery leakage is observed, avoid any contact with affected area and properly dispose of the battery. If you come in contact with battery leakage, rinse exposed area with soap and water. If it contacts the eye, burn or damage to your battery, do not allow a metal object to touch battery contacts. the eye with water for 15 minutes and seek medical attention. 6. Dispose of used battery promptly. 7. When discarding a battery, contact your local waste disposal provider to understand local restrictions for Do not disassemble or dispose of in Keep away from children. To help you get started with your XT40 Series mobile computer, this guide features:

- Hardware Overview

- Getting Started A. Install the Battery B. Charge the Battery C. Remove the Battery + Access MicroSD and SIM Card Slots

- Battery warnings and safety guidelines. Contents of this guide are subject to change. For the most current version of this guide and additional product details, visit www.janam.com. For software updates and information, visit www.janam.com/product-zone. disposal or recycling of batteries. BATTERY CHARGER SAFETY GUIDELINES. 1. Do not use the equipment in or near areas in which sparks are likely or possible. 2. Do not let equipments metal contacts and electrical sockets come in contact with metal objects. 3. For indoor use only. Do not expose the equipment to rain or any liquids. 4. Do not use or store the equipment in direct sunlight or in areas that are prone to get hot such as in a parked vehicle, near a heat duct or close to other heat sources. 5. Keep equipments metal contacts and electrical sockets free from debris that could obstruct charging or could cause a short circuit. Page 7 Page 2 XT40 Series Quick Start Guide Hardware Overview 1. 2. 3. 4. 5. 6. Barcode Scanner Camera 3.5mm Audio Jack Touch Screen Right Trigger Power Key 7. Micro USB 8. 9. Pogo Pin Connector Volume Key 10. Left Trigger 1 2 3 4 5 6 10 9 8 7 Hardware Overview 1 2 3 4 1. 2. 3. Camera Speaker SIM Card Slot 4. MicroSD Card Slot Page 3 4 egaP Janam Technologies LLC Getting Started A. INSTALLING THE BATTERY 1. To access the battery compartment, remove the handstrap by pulling down the plastic clip located on the bottom of the XT40. Move both tabs on the battery cover to the unlock position and pull the cover away from the device. 2. Position the battery so that the text Insert this direction. is on the left side and snap into place. 3. Replace the battery cover by positioning the bottom prongs first and snapping cover into place. 4. Move both tabs on the battery cover to the lock position. B. CHARGING THE BATTERY Important Note: The main battery charges the backup battery in the XT40 Series device. When discharged, the backup battery requires approx. 1.5 hours to recharge. To charge the battery using the included AC/DC Power Adapter Kit:

1. Connect the AC/DC adapter to XT40 Series. 2. Plug in the AC/DC adapter. Use only easily accessible wall sockets that are easily reached with the length of supplied power cable. To charge the battery using a Cradle Kit:

1. Connect the power supply to the cradle. 2. Plug in the power supply. Use only easily accessible wall sockets that are easily reached with the length of supplied power cable. 3. Place the device in cradle. The LED on the device will illuminate to con irm connection. 4. The battery is fully charged in approximately 2.5 hours. To charge a battery in the spare battery well, insert the battery into the well top down (connectors on the battery should face downward and to the back of the cradle) and gently press down. The LED light on the cradle will illuminate to con irm connection. Getting Started (continued) To charge the Backup Battery:

1. Navigate to the Home Screen -> App drawer -> Settings -> Battery. 2. Select Backup Battery Charge option. C. ACCESSING SIM CARD SLOT and MICROSD CARD SLOT 1. Remove the back cover. 2. Remove battery from the XT40. 3. MicroSD card slots and SIM slot are now accessible. Insert the MicroSD or SIM with gold-colored contacts facing downward. 4. Replace the battery. 5. Replace the battery cover. Page 5 Page 6 XT40 Series Series Quick Start FCC Caution 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. IC Caution Operations in the 5.15-5.25GHz band are restricted to indoor usage only. English:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause in terference, and (2) This device must accept any interference, including interference th at may cause undesired operation of the device. French:

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

JANAM Janam Technologies LLC MODEL:XT40 PRODUCT:Mobile Computer FCC ID:UTWXT40WA 1C:6914A-XT40WA INPUT Fe 5V == 3A/9V= 2A/12V 1.54 Made in China

IYI UT OO POUO LOL) QL LA LLL AKL Kl WD _ i]

i S58;

BU A sgn sa 706 08 OL 09 OS Ob OE Oz 01 90106 08 OL 09 OS OF OE Oc OF weiss ez my OL 0 OF 0S 09 OZ 08 06 nvliarlieliny OZ OF Ob OS 09 04 08 06D, 0F Oz OE Ob OS 09 OL 08 |

OObaL oz o ov os 09 o2 o8 06 00Zor oz o FvvlvastogtuvilagylulaysteutiaeTaa uel alia eT e

Janam Technologies LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Company name: Janam Technologies LLC Address: 100 Crossways Park West Suite 105 Woodbury, NY 11797, USA Product Name: Mobile Computer FCC ID: UTWXT40WA Model(s): XT40 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing We, [Janam Technologies LLC] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Yours Sincerely, Name: Harry Lerner Date: 2023-08-22 Title: CEO Signature of applicant: | js 6 _-/

Rev 1/26/2023

Janam Technologies LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-08-22 Ref: Attestation Statements Part 2.911(d) (7) Filing We, [Janam Technologies LLC | (the applicant) certifies that, as of the date of the filing of the application, designate our self as U.S. agent for service of process. Designated U.S. Agent Information:

Name: Janam Technologies LLC Address: 100 Crossways Park West Suite 105 Woodbury, NY 11797, USA Contact Person: Harry Lerner Tel.: +1.516.677.9500 Email: harry.lerner@janam.com FRN: 0015791353 Sincerely, Applicant signature: It 6 Ls , Applicant printed name: Harry Lerner Company Name: Janam Technologies LLC Address: 100 Crossways Park West Suite 105 Woodbury, NY 11797, USA Email: harry.lerner@janam.com Rev 1/26/2023

Janam Technologies LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Company name: Janam Technologies LLC Address: 100 Crossways Park West Suite 105 Woodbury, NY 11797, USA Product Name: Mobile Computer FCC ID: UTWXT40WA Model(s): XT40 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing We, [Janam Technologies LLC ] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Yours Sincerely, Name: Harry Lerner Date: 2023-08-22 Title: CEO Signature of applicant Ibo Rev 1/26/2023

FCC Letter of Authorization Company: Janam Technologies LLC Address: 100 Crossways Park West Suite 105 Woodbury, NY 11797, USA Product Name: Mobile Computer Model Number: XT40 FCCID: UTWXT40WA We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Harry Lemer * Date: 2023/08/22 Title: CEO Signature of applicant:

Kb.

Janam Technologies LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023/08/22 Subject; Request for Confidentiality FCC ID: UTWXT40WA To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. 4 Schematic Diagram i Block Diagram Operational Description BOM List Tune up procedure Software Security Info In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Ci Test Setup Photos C1 Internal Photos

(1 User Manual O For 45 days, pursuant to Public Notice DA 04-1705. OR O For 180 days pursuant to KDB 726920 DO1. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: | L 6 _L-

Name: Harry Lerner

FCC Software Configuration Control Declaration Date: Aug 22, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product: Mobile Computer Model Number: XT40 FCCID: UTWXT40WA Regarding FCC Country Code Selection guidelines identified in KDB 594280 D02 UNII Device Security v011r03. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Harry Lerner Date: 2023/08/22 Title: CEO Signature of applicant: | L 6 L- . FCC Software Configuration Control Declaration