submitted | available | document details (if available) | source link |
---|---|---|---|
GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version) |
various | User Manual 2 | Users Manual | 4.45 MiB |
Chapter 2 START THE BASIC OPERATION Chapter 2 START THE BASIC OPERATION When * basic adjustment is made by the serviceman etc. beforehand, please perform as it is.
(In case of no adjustment is done by the serviceman etc. beforehand, please through eyes to Chapter 5 for the time being, and after getting to know the outline of operation of this radar, perform Initial setting of Chapter 7.) The screen is a touch screen and can be operated by tracing a screen by a finger flip or touching. The term of operation:
TAP: Push a screen display position once by a fingertip. Flick: Rub a screen display position by a fingertip.
(A state recognized according to the rubbed direction) Swipe: Rub a screen display position keeping on touch by a fingertip. Long tap: Pushing a screen display position, continued more than 3 seconds or more by a fingertip. The operation of a Rotary knob:
Click: Push in a Rotary knob once. Rotating and choosing the state of a screen, then click and fix. General using : The touch panel function is select absolute positions on panel, on the other hands, Rotary knob select sequential data up and down. and, at selection data appeared then click and fix. Only Cross cursor is individual moving, no relation to another. 29 Chapter 2 START THE BASIC OPERATION Push PWR/CLR button. Power on startup screen. Startup screen. (3 Startup screen possible to select.) Swipe on the screen for select the startup screen. 30 Rotary knob. Chapter 2 START THE BASIC OPERATION Push Rotary knob and rotate to select the starting item.. icon at bottm side, then full icons can be seen. Tap Keep press and rotate the rotary knob, then screen brillance menu will be open. Rotate Rotary knob at suitanble brilliande level. Release Rotary knob, then the brillance level is fixed The turn while pressing Select the icon you needed by turning the knob Full icons will be appeared. Brillance menu will be appeared. 31 Chapter 2 START THE BASIC OPERATION Tap Sleep Cursor Sleep TX/STBY Tap TX/STBY Tap TX/STBY Tap After a few seconds, the icons fade out. Push or click the Rotary knob. Activate Cursor Activate TX/STBY Crick the Rotary knob will appear the icons 32 2-1 GUIDE FOR OPERATION Chapter 2 START THE BASIC OPERATION Multi-Touch screen. Operate using tap flick long tap swipe by fingertip. Rotary knob. Rotation: select the sequential menu. Push or click fix menu data. Front view 2-2 POWER ON (STAND BY FOR TRANSMIT) POWER ON OFF, CLEAR PUSH BUTTON. POWER ON/OFF CLEAR OF MENU PRESS PWR / BUTTON Start to display screen. Startup screen 33 Chapter 2 START THE BASIC OPERATION 2-3 DISPLAY SCREEN 2-3-1 SCREEN LAYOUT Course Speed (through ground) Range Range interval Own ship. Longitude/Latitude. depth. Own ship position mark. USB Port Alarm Speaker POWER ON OFF,CLEAR PUSH BUTTON. POWER ON/OFF CLEAR OF MENU Push Rotary knob, then appears some menu. Rotation of Rotary knob can select menu of activated icon. Function call icon will be displayed. 34 Chapter 2 START THE BASIC OPERATION Normal ST-BY screen,
* ST-BY Disp, Select.:
Various ST-BY screen. Course Speed Graphical ST-BY screen
* ST-BY Disp, Select.:
Tap White dot Tap Normal ST-BY screen, Normal ST-BY screen, Normal Tap White dot Tap Graphical ST-BY screen Graphical ST-BY screen Graphical Course Speed Course Speed Tap White dot Own ship position Tap Own ship position Own ship position Numeric Display ST-BY screen. Numeric Display ST-BY screen. Numeric Display ST-BY screen.
* ST-BY Disp, Select.:
Numeric Display 35 Chapter 2 START THE BASIC OPERATION Push Rotary knob, select TX icon by rotating Rotary knob and push Rotary knob. TX screen. Push Rotary knob & select TX icon by rotating. Set focus to TX icon. Or Push Rotary knob Tap TX icon Start TX Tap Tap Push Rotary knob Tap UP icon Tap DOWN icon 36 Chapter 2 START THE BASIC OPERATION 2-3-2 ICONS TABLE The icons which will appear by screen operation. GAIN VRM CURSOR MODE RIVER RAIN GURDZONE SETTING MODE FIOAT SEA MARK MENU MODE OFF BRILLIANCE AIS USER1 DAY TX-STBY TT USER2 NIGHT RANGE MOB MODE STANDARD EBL OFFCENTER MODE COAST 37 Rotate Rotary knob Chapter 2 START THE BASIC OPERATION Appear icons after Pushing Rotary knob No operation about 10 second. Display the function icons. Push Rotary knob Rotate for icon selection. Selected icon is focused. Push Rotary knob, then appear the setting menu. Set level by Rotary knob or flick bar graph.. Then push Rotary knob, data is fixed. 38 Chapter 2 START THE BASIC OPERATION TX Tap TX/STBY icon, or Push rotary knob when TX/STBY icon is focused. Tap icon or push rotary knob ST-BY Scanned display is appeared Tap icon or push rotary knob 39 Chapter 2 START THE BASIC OPERATION Tap GAIN Adjust icon, or Push rotary knob when GAIN Adjust icon is focused. The case of ST-BY The case of TX Adjustment Gain Bar is appeared Adjustment Gain Bar is appeared Tap Auto of Gain setting mode Tap Auto of Gain setting mode Gain is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Tap + or -
Or Or In TX mode, can be adjusted while monitoring the display echo. Tap return icon Push Rotary knob Or The data is fixed, and then return 40 Tap SEA Adjust icon, or Push rotary knob when SEA Adjust icon is focused. Chapter 2 START THE BASIC OPERATION Adjustment Bar is appeared Tap Auto of SEA setting mode Tap Auto of SEA setting mode SEA is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Tap + or -
Or Or Can be adjusted while monitoring the display echo. Tap return icon Push Rotary knob Or The data is fixed, and then return 41 Chapter 2 START THE BASIC OPERATION Tap RAIN Adjust icon, or Push rotary knob when RAIN Adjust icon is focused. Adjustment Bar is appeared Tap Auto of RAIN setting mode Tap Auto of RAIN setting mode RAIN is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Tap + or -
Or Or Can be adjusted while monitoring the display echo. Tap return icon Push Rotary knob Or The data is fixed, and then return 42 Chapter 2 START THE BASIC OPERATION 2-3-3 BRIEF EXPLANATION OF ICONS FUNCTION Brief explanation of each icon. GAIN (gain control) adjustment:
Set up the sensitivity of Radar echo.. SEA (sea-clutter rejection) adjustment:
Control the sea clutter level near the ship. Long distant echo gain is remaining as it is, and gain is lowered as to short distance. Adjust the target ship is clearly observe and reject the sea clutter on screen as much as possible. RAIN (rain-and-snow-clutter rejection) adjustment:
This type radar uses (X) band microwave (wavelength: 3cm). This microwave can detectable more far range in fine weather, but in rain or snow weather, the detectable range decrease remarkably. The control is adjusted for separate the target and rain or snow as long as possible. BRILL (brightness) adjustment: Set up the brightness of a screen. It sets up brightly daytime and sets up not dazzle at night MOB (Man Over the Boat): When the crew fall into over the boat by accident. Carry out a tap MOB icon immediately. The radar memorizes the place latitude and longitude information, and continues displaying the (MOB)place on a screen. When going to rescue, navigator can take course to the(MOB)point on screen.
(Important: GPS signal must be connected in this function.) TT DATA (target tracking) Data which is tracking automatically is displayed. Data is display the direction, the distance, the speed. This function must be required the heading signal and log signal. Measures reading of a direction can select from north(N-UP) and measure from self-ship
(H-UP). The speed display can select the relative speed mode or absolute speed mode. 43 Chapter 2 START THE BASIC OPERATION AIS DATA (when received the AIS signal, the data of MMSI of the vessel which has transmitted, latitude, longitude, a direction of movement, speed, rate of turn, etc. is displayed.)
(AIS receiver signal is necessary.) EBL (electronic bearing line) Measure the target direction by using cursor line. VRM (variable range marker) Measure the target distance by using circle line. Off-center (Normally own position is the center of screen, but it is possible to move own position from fixed center of screen). Tap the icon will shift the own position. Shifting point are fixed 5 positions only. TX (transmission), ST-BY (standby) Whenever it carries out a tap, transmission and ST-BY are changed. RANGE (range scale) The range scale to observe is changed. The maximum range is limited by the scanner type which is connected. NKE-1066 scanner 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1.5NM 3NM 6NM 12NM 24NM.
(Also 1NM, 2NM, 4NM, 8NM, 16NM are possible by system menu setting.) NKE-2044 scanner 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1.5NM 3NM 6NM 12NM 24NM 48NM.
(Also 1NM, 2NM, 4NM, 8NM, 16NM, 32NM are possible by system menu setting.) 44 Chapter 2 START THE BASIC OPERATION Various system setups. Tap the icon, the adjustment menu will be displayed. Choose the item to set up individually. Code input 0 is setting for service menu. Next User menu Special setting menu for user. 45 Chapter 2 START THE BASIC OPERATION GUARD ZONE setup Set up the watching area around own-ship. If a target goes into the set-up area, generate the alarm sound or signal.. On the other hand, if a target goes out the set-up area, generate the alarm sound or signal, too. One of both is possible to select. Cursor: A tap is carried out, start, drag and tap off on the target. The position of this cursor is indicated. Various kinds of pointing actions uses this cursor.. Tracking of target, AIS data display, setting of guard zone, etc. MARK: Use when plot a mark on the screen. Moreover, also when deleting an unnecessary mark, it uses. 46 2-4 TRANSMIT Chapter 2 START THE BASIC OPERATION
(90 seconds pre-heat time is required for cold start, because of the Magnetron heater.) After 90 seconds, anytime transmitting is possible. Various ST-BY screen. Power ON Push PWR/CLR button 47 Chapter 2 START THE BASIC OPERATION Start by the tapping white dot or the pushing rotary knob White dot White dot rotary knob Tap TX/ST-BY icon or Select TX/ST-BY icon and push rotary knob, and then transmitting. TX/ST-BY icon Select TX/ST-BY icon and push rotary knob rotary knob Transmitting screen. No operation of 10 second, small menu will be fade out. 48 Chapter 2 START THE BASIC OPERATION 2-5 LEAVE THE USEFUL ICON ON SCREEN Basic icon display. How to copy icon. Full icon display Fixed icon (TX/ST-BY, Gain) User free area of menu icon. Tap UP icon icons that can be copied to user free area. Fixed icon (TX/ST-BY, Gain) User free area of menu icon. Tap and hold the icon, Tapped icon is copied to free menu area Up to 4 icons can copy the user free area. 49 Chapter 2 START THE BASIC OPERATION Full icon display Basic icon display. How to remove icon. How to add another icon. 50 Tap and hold the icon, on user free area Tapped icon is removed from free menu area Then the remaining icons are shifted to the left. Tap and hold the icon, Tapped icon is copied to free menu area Chapter 2 START THE BASIC OPERATION 2-6 FUNCTION CALL BY SCREEN TAP Various types of icon.
(1) Start function immediately.
(2) Move into function setting.
(3) Double tap start from resist setting state and open menu. TX, ST-BY Every tap changes TX, ST-BY alternately Change Range Rotate the rotary knob with monitoring range. tap increase range tap decrease range Or While range icon focused Or Or Change brightness by Flick the green belt. Tap + or -
51 Chapter 2 START THE BASIC OPERATION Screen brightness adjustment Tap the icon, then display Adjust menu. Rotate the rotary knob with monitoring green bar. Or Or Change brightness by Flick the green belt. Tap + or -
Also using Rotary knob is possible to adjust. Keep press on the Rotary knob and turn. Anytime its possible to change Setting level is displayed down side of each icon. Green bar length is proportion to setting level.
*POWER ONOFF is operate from PWR/CLR BUTTON! only. Cant control from screen menu. Keep press on the Rotary knob. 52 Chapter 3 ADJUST THE RADAR ECHO Chapter 3 ADJUST THE RADAR ECHO 3-1 CHANGE RANGE tap increase range tap decrease range This picture is selected 1.5 nm range. Outer dashed line shows the maximum observation range. RANGE RANGE RING INTAVAL Gain is easily changed by the tap of increase / decrease icon as shown in the figure below tap increase range 1.5NM tap decrease range Or Adjust while range icon focused by tapping or selection of rotary knob Or Or Rotate the rotary knob with monitoring green bar. Change brightness by Flick the green belt. Tap + or -
53 Chapter 3 ADJUST THE RADAR ECHO Range scale, NKE-1066 scanner It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM 16NM 24NM and order. NKE-2044 scanner It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM 16NM 24NM 32NM 48NM and order. A picture will change on a scale as shown in the following figure, as range changes. The radius of the circle shows the range. Example: Video change 0.0625NM 0.125NM 0.25NM 0.5NM 0.75NM 1NM 2NM 3NM 4NM 6NM 8NM 1.5NM 12NM 16NM 24NM 32NM 48NM 54 is NKE-2044scanner only Chapter 3 ADJUST THE RADAR ECHO 3-2 ADJUSTS GAIN (RADAR SENSITIVITY) Radar must be set suitable gain, or cant use as a radar Adjust while Gain icon focused by tapping or selection of rotary knob icons green belt show the adjusted level of GAIN How to change the Gain: See the method of Gain adjustment of Chapter2 Example of echo sensitivity as following echo sensitivity Low echo sensitivity Middle echo sensitivity High 6NM 6NM 6NM GAIN set Exceed If GAIN control is the maximum, noise will appear on whole screen. 6NM On clear weather normally set almost maximum GAIN. When rough weather or rough sea or heavy rain and, snow, adjust mix up SEA,RAIN GAIN. And select suitable level each. 55 Chapter 3 ADJUST THE RADAR ECHO 3-3 ADJUST SEA (CLUTTER CONTROL) Radar must be set suitable sea control, or cant use as a radar Adjust while SEA icon focused by tapping or selection of rotary knob icons green belt show the set level of SEA How to change the SEA: See the method of SEA adjustment of Chapter2 SEA Level Low SUITABLE Level 0.5NM 0.5NM 56 Chapter 3 ADJUST THE RADAR ECHO 3-4 ADJUST RAIN AND SNOW CLUTTER CONTROL Radar must be set suitable rain and snow control, or cant display the suitable picture. Adjust while RAIN icon focused by tapping or selection of rotary knob icons green belt show the set level of RAIN How to change the RAIN: See the method of RAIN adjustment of Chapter2 RAIN Small (usually) RAIN Excessive (the target of the radius direction becomes small.) 6NM clear weather (RAIN 0) Rain control is effective, if the weather light rain or snow.
(RAIN *). Too much suppression will disappear the small target, so set a little. 6NM not clear weather (RAIN 0).
(RAIN *) 57 Chapter 3 ADJUST THE RADAR ECHO 3-5 ADJUST BRILLIANCE OF SCREEN Double TAP of screen can change BRILLANCE of screen. Normal TAP, Flick operations also possible to change screen brilliance. range. Double Tap icons green belt show the set level of BRILLIANCE How to change the BRILLIANCE: See the method of BRILLIANCE adjustment of Chapter2 58 Chapter 3 ADJUST THE RADAR ECHO FOR REFERENCE Observing the Radar screen, GANI and SEA control adjustment is essential adjustment. RAIN: Normally set 0, when light rain or snow, turn proportion to reject rain noise on screen. GAIN: Set the GAIN adjustment for long range (more than 6nm) target can observe clear. Under this conditions, short range near own ship, cannot observe small target because of high clutter and high gain. To avoid this failure, use SEA control, and suppress near range clutter noise. If suitable adjustment is done, costumer can observe clear target from short range to long range. ACTUAL OPERATION Set RAIN Minimum position Set 6nm RANGE, and observe more farther special target. Set GAIN control so as to the special target is observe clearly. Change to 0.5nm RANGE Set SEA control so as to the near target can observe clearly. Basically, RAIN control is minimum state, but according to the weather conditions, to reject rain or snow clutter, little bit turn to effective point. 59
This product uses the FCC Data API but is not endorsed or certified by the FCC