submitted | available | document details (if available) | source link |
---|---|---|---|
GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version) |
various | User Manual 5 | Users Manual | 4.48 MiB |
Chapter 8 DETAIL PERFORMANCE SETTING Chapter 9 MAINTENANCE AND CHECK 9-1 ROUTINE MAINTENANCE For operating the radar equipment in the good conditions, it is necessary to make the maintenance work as described below. If maintenance is made properly, troubles will reduce. It is recommended to make regular maintenance work. Common points of maintenance for each unit are as follow:
Clean the equipment. Remove the dust, dirt, and sea water rest on the equipment cabinet with a piece of dry cloth. Especially, clean the air vents with a brush for good ventilation. 138 9-2 MAINTENANCE OF EACH UNIT 9-2-1 SCANNER NKE-1066 Chapter 9 MAINTENANCE AND CHECK DANGER When conducting maintenance work on the antenna, make sure to turn its main power off. Failure to comply may result in electrocution or injuries. 139 Chapter 9 MAINTENANCE AND CHECK 9-2-2 SCANNER NKE-2044 DANGER When conducting maintenance work on the antenna, make sure to turn its main power off. Failure to comply may result in electrocution or injuries. 140 Chapter 9 MAINTENANCE AND CHECK 9-2-3 DISPLAY NCD-2256 DANGER When cleaning the display screen, do not wipe it too strongly with a dry cloth. Also, do not use gasoline or thinner to clean the screen. Failure to comply will result in damage to the screen surface. Dust accumulated on the screen will reduce clarity and darken the video. For cleaning it, wipe it with a piece of soft cloth (flannel or cotton). Do not wipe it strongly with a piece of dry cloth nor use gasoline or thinner. 141 Chapter 9 MAINTENANCE AND CHECK 9-3 PERFORMANCE CHECK Make operational check on the radar equipment regularly and if any problem is found, investigate it immediately. Pay special attention to the high voltage sections in checking and take full care that no trouble is caused by any error or carelessness in measurement. Take note of the results of checking, which can be used effectively in the next check work. Operational check shall be made in accordance with Table 4.3-1 Function Check List in the order as specified in it. Table 9-3-1 Performance Check List 142 Chapter 9 MAINTENANCE AND CHECK 9-3-1 TEST MENU The performance status of this radar equipment can be checked on the Test Menu. 9-3-2 SYSTEM INFORMATION Displays the current system information. (software version information). 9-3-3 SYSTEM TIME Displays the following system time information. Indicator Running Time Scanner Transmit Time Scanner Motor Time Scanner Running Time 143 Chapter 9 MAINTENANCE AND CHECK 9-3-4 SCANNER INFORMATION Displays the following scanner information. Transmitted output power Motor Type Magnetron Current 9-3-5 HARDWARE INFORMATION Displays the following hardware information. Serial Number MAC Address Temperature 9-3-6 ERROR LOG The error log displays previously occurred system alarms with the dates and times when they occurred. 9-3-7 LINE MONITOR Serial communication data can be seen on the built-in Line monitor. Line monitor can be used to make sure that the serial data are received properly 144 Chapter 9 MAINTENANCE AND CHECK The following tests can be performed. 9-3-8 SELF TEST Key Test Buzzer Test Key Light Test Monitor Display Test Memory Test Line Test Sensor Test 145 Chapter 9 MAINTENANCE AND CHECK 146 9-4 REPLACEMENT OF MAJOR PARTS Chapter 9 MAINTENANCE AND CHECK 147 Chapter 9 MAINTENANCE AND CHECK 9-4-1 PARTS REQUIRED FOR PERIODIC REPLACEMENT Here are parts required for periodic replacement. PARTS NAME 1. MAGNETRON 2. MOTOR INTERVAL 4,000 HOURS 10,000 HOURS 148 9-5 FAULT FINDING Chapter 9 MAINTENANCE AND CHECK 9-5-1 ALARMS AND OTHER DISPLAY LISTS 9-5-2 FUSE 9-6 TROUBLE SHOOTING 9-6-1 INCLUDED ACCESSORIES 9-6-2 SPECIAL PARTS Location Parts No. Name NKE-1066 V101 NKE-2044 V101 NKE-2044 A101 Magnetron Magnetron Circulator Type M1624 Code Manufacture New JRC MSF1421B 5VMAA00092 New JRC FCX68R 5AJIX00027 Orient Microwave NKE-2044 A102 Diode Limiter NJS6930 5ATBT00006 New JRC 149 Chapter 9 MAINTENANCE AND CHECK 9-6-3 CIRCUIT BLOCK TO BE REPAIRED JMA-1032 Location Circuit Block Type Remarks Motor unit H-7BDRD0053 Modulation circuit CME-396 Include IF Amplifier Scanner Scanner Scanner Display Unit Display Unit Micro wave unit Transmitter/ receiver Power Supply circuit Process Circuit CMN-924/NZT-1066 CBD-1928 CDC-1433 NZP-2256 Include Receiver frontend Display Unit LCD Panel JMA-1034 Location Circuit Block Type Remarks Scanner Scanner Scanner Motor unit H7BDRD0052A Modulation circuit CME-397 NZT-2044 Receiver NRG-242 CBD-1928 CDC-1433 NZP-2256 Display Unit Display Unit Power Supply circuit Process Circuit Display Unit LCD Panel 150 Chapter 9 MAINTENANCE AND CHECK 151 Chapter 10 AFTER-SALE SERVICE Chapter 10 AFTER-SALE SERVICE 10-1 KEEPING PERIOD OF MAINTENANCE PARTS Keeping period of maintenance parts is ten years from the production is discontinued. 10-2 WHEN YOU REQUEST FOR REPAIR If you suppose the product may be out of order, read the description in "9-2-5 FAULT FINDING" and "9-2-6 TROUBLE SHOOTING", and check the suspected point again. If it is still out of order, you are recommended to stop operation of the equipment and consult with the dealer from whom you purchased the product, or our branch office in your country or district, the sales department in our main office in Tokyo. Repair within the Warranty Period If any failure occurs in the product during its normal operation in accordance with the instruction manual, the dealer or JRC will repair free of charge. In case that any failure is caused due to misuse, faulty operation, negligence or force major such as natural disaster and fire, the product will be repaired with charges. Repair after the Warranty Period. If any defective function of the product is recoverable by repair, the repair of it will be made at your own charge upon your request. Necessary Information for Repair
Product name, model, manufacturing date and serial number
Trouble conditions (as detailed as possible. Refer to page "10-4 Radar failure check list".)
Name of company/organization, address and telephone number 10-3 RECOMMENDED MAINTENANCE The performance of the product may deteriorate due to the secular change of the parts used in it, though such deterioration depends upon the conditions of operation. So checkup and maintenance is recommendable for the product in addition to your daily care. For maintenance, consult with the near-by dealer or our sales department. Such maintenance will be made with charges. For further details of after-sale service, contact the JRC Offices. 152 10-4 RADAR FAILURE CHECK LIST Chapter 10 AFTER-SALE SERVICE 153 Chapter 11 DISPOSAL Chapter 11 DISPOSAL 11-1 DISPOSAL OF THE UNIT When disposing of this unit, be sure to follow the local laws and regulations for the place of disposal. 154 11-2 DISPOSAL OF USED MAGNETRON Chapter 11 DISPOSAL A magnetron is used for the scanner (NKE-1066) (NKE-2044). When the magnetron is replaced with a new one, return the used magnetron to our dealer or business office. For detail, consult with our dealer or business office. 11-3 CHINA ROHS 155 Chapter 11 DISPOSAL 156 Chapter 12 SPECIFICATIONS Chapter 12 SPECIFICATIONS NKE-1066 scanner NCD-2256 display 1.5ft scanner 4kw Radome diameter 450mm NKE-2044 scanner 2ft Scanner 4kw Radome diameter 620mm Display 7inches wide LCD 158 Chapter 12 SPECIFICATIONS 12-1 SCANNER DIMENSION 12-1-1 NKE-1066 NKE-1066 1.5ft scanner 4kw radome 450mm 4-40 RUBBER PLATE 159 Chapter 12 SPECIFICATIONS 12-1-2 NKE-2044 160 12-2 DISPLAY DIMENSION 12-2-1 NCD-2256 Chapter 12 SPECIFICATIONS 161 Chapter 12 SPECIFICATIONS 162 12-3 EQUIPMENT OUTLINE Chapter 12 SPECIFICATIONS This equipment is a marine radar for vessels and work boats which consists of the display unit including 7 inch wide VGA color LCD Monitor unit, Keyboard unit, Processing unit and consists of the 1.5 ft /2ft radome type scanner unit. The processing unit uses SOC (LUPIM) developed by JRC and the LCD monitor unit uses panel with touch sensor (resistance film type). The operation can be realized intuitive and simple. 12-3-1 CONFIGULATION 1) Display unit NCD-2256 Integrated the 7 inch wide VGA color LCD Monitor unit, Keyboard unit and Processing unit 2) Scanner unit X-band 1.5ft(4kW) radome type is NKE-1066 X-band 2ft(4kW) radome type is NKE-2044 12-3-2 FEATURE 1) The screen resolution is 800x480dots (WVGA). The LCD monitor unit with touch sensor (resistance film type). 2) Highly efficient signal processing using the SOC including DSP. 3) TT and AIS function are prepared by SOC using. 12-3-3 RADAR MODEL JMA-1032 1.5ft Scanner unit JMA-1034 2.ft Scanner unit 163 Chapter 12 SPECIFICATIONS 12-3-4 SYSTEM DIAGRAM JMA-1030 Series system diagram 1.5feet Scanner Unit
(NKE-1066) 2feet Scanner Unit
(NKE-2044) Radome diameter 450mm Radome diameter 620mm CFQ9924-5,10,15,20,300
*STANDARD LENGTH 10m OPTION:
(cablelength:5m/15m/20m/30) JMA-1034 RADAR JMA-1032 RADAR External Navigational Signal input. NMEA 3 input ports
(GPS,AIS,DEPTH) Ships Main Power
(10.8-31.2VDC) CFQ-9900
(cable length 2m)
*INCLUDING FUSE IN PLUS LINE FUSE TYPE: 7.5A/58V 7inch WIDE VGA COLOUR LCD DISPLAY
(NCD-2256) 164 12-4 GENERAL SPECIFICATIONS Chapter 12 SPECIFICATIONS
(1) Class of Emission
(2) Display
(3)Display capability
(4) Screen
(5) Range Scale
(6) Range Resolution
(7) Minimum Detective Range
(8) Range Accuracy
(9) Bearing Accuracy
(10) Bearing Indication
(11) Ambient Condition Standards Temperature P0N Color Raster Scan WVGA (800x480dots) Screen 7-inch Color LCD with touch sensor (resistance film type) 0.0625, 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48NM
(48 NM: only 2feet type scanner is available) User can add 1, 2, 4, 8, 16, and 32NM
(32 NM: only 2feet type scanner is available) Less than 30m Less than 40m Less than 1% of the maximum distance of the range scale in use or less than 15m whichever is greater. Less than 1 RM: Head-up, North-up, Course-up TM: North-up, Course-up IEC60945 Ed.4.0 Scanner Operation: -25 to +55C / Storage: -25 to +70C Other Unit except Scanner Operation: -15 to +55C / Storage: -15 to +70C Relative Humidity Vibration Velocity of the wind Waterproof/dustproof
+40C, 93%
2 to 13.2 Hz, amplitude1mm 13.2 to 100 Hz 0.7 G 100kn Scanner Display unit IP26 IP55
(12) Power Supply Input
(13) Power Consumption
(14) Pre heat time
(15) Display unit
(16)Inter-unit Cables DC 10.8-31.2V (DC12-24V-10%+30%) Approx. 50W (NKE-1066/NKE-2044). Maximum: 50W (NKE-1066: SP1, NKE-2044: LP2 transmitting) Approx. within 1min30sec. Refer to Display unit Specifications Using common scanner connecting cable CFQ-9924-10 Standard Length 10m Maximum cable length 30m 165 Chapter 12 SPECIFICATIONS 12-5 SCANNER 12-5-1 SCANNER (NKE-1066) SPECIFICATION
(1) Dimensions
(2) Mass
(3) Polarization
(4) Antenna Directivity Height 231mmDiameter of radome 450mm Approx. 5.5kg Horizontal (antenna length 1.5 feet) Horizontal Beam Width (-3dB) Vertical Beam Width (-3dB) Less than -21dB (less than 10 from the main lobe) Approx. 27rpm (16/27/36/48rpm are available) 941030MHz 4 kW Magnetron [M1624]
5.2 25 Side lobe Level
(5) Rotation
(6) Transmitting Frequency
(7) Peak Power
(8)Transmitting Tube
(9) Pulse width/ Repetition Frequency (Bandwidth) SP1: 0.08s/4000 Hz (Wide 20MHz) SP2: 0.08s/2250 Hz (Wide 20MHz) SP3: 0.13s/1700 Hz (Wide 20MHz) MP1: 0.25s/1700 Hz (Middle 6MHz) MP2: 0.5s/1200 Hz (Narrow 3MHz) LP1: 0.8s/750 Hz (Narrow3 MHz)
(S: Short pulse, M: Middle pulse, L: Long pulse) 0.0625NM SP1 0.125NM SP1 0.25 NM SP1 0.5 NM SP1 / MP1 0.75 NM SP2 / MP1 1.5 NM SP2 / MP1 / MP2 3 NM SP3 / MP1 / MP2 6 NM MP2 / LP1 12 NM MP2 / LP1 24 NM LP1 Circulator + Diode Limiter
(Diode Limiter is included in the frontend) MIC 60MHz Log Amplifier (Gain: more than 90dB) 6dB(Average) Manual/Auto
(10) Range Information
(11) Duplexer
(12) Front End Module
(13) IF Frequency
(14) IF AMP
(15) Overall Noise Figure
(16) Tuning 166 Chapter 12 SPECIFICATIONS 12-5-2 SCANNER (NKE-2044) SPECIFICATION
(1) Dimensions
(2) Mass
(3) Polarization
(4) Directional Characteristic Height 280mmDiameter of radome 620mm Approx. 10.5kg Horizontal (antenna length 2 feet) Horizontal Beam Width (-3dB) Vertical Beam Width (-3dB)
-21dB or less (less than 10 from the main lobe) Approx. 27rpm (16/27/36/48rpm are available) 941030MHz 4 kW Magnetron [MSF1421B]
4 25 Side lobe Level
(5) Rotation
(6) Transmitting Frequency
(7) Peak Power
(8)Transmitting Tube
(9) Pulse width/ Repetition Frequency (Bandwidth) SP1: 0.08s/4000 Hz (Wide 20MHz) SP2: 0.08s/2250 Hz (Wide 20MHz) SP3: 0.13s/1700 Hz (Wide 20MHz) MP1: 0.25s/1700 Hz (Middle 6MHz) MP2: 0.5s/1200 Hz (Narrow 3MHz) LP1: 0.8s/750 Hz (Narrow3 MHz) LP2:1.0us/650Hz (Narrow:3MHZ)
(S: Short pulse, M: Middle pulse, L: Long pulse) 0.0625NM SP1 0.125NM SP1 0.25 NM SP1 0.5 NM SP1 / MP1 0.75 NM SP2 / MP1 1.5 NM SP2 / MP1 / MP2 3 NM SP3 / MP1 / MP2 6 NM MP2 / LP1/ LP2 12 NM MP2 / LP1/ LP2 24 NM LP2 48 NM LP2 Circulator + Diode Limiter MIC 60MHz Log Amplifier (Gain: more than 90dB) 6dB(Average) Manual/Auto
(10) Range Information
(11) Duplexer
(12) Front End Module
(13) IF Frequency
(14) IF AMP
(15) Overall Noise Figure
(16) Tuning 167 Chapter 12 SPECIFICATIONS 12-6 DISPLAY 12-6-1 INTEGRATED DISPLAY UNIT (NCD-2256) 1) Structure Desk Top Integrated Type
(LCD Monitor Unit/Keyboard Unit/Processor Unit Integrated Structure) 2) Dimensions 3) Mass 4) Tune Method Vertical installation only desk top integrated type Option: Overhead Mounted kit installation Height 235.2mm Width 162mm Depth 77.3mm
(The U style mount base and the both sides knob bolts are included.) Approx. 1.8kg Manual / Auto
(Bar-graph indication is displayed at the time of adjustment.) 5) STC (SEA) 6) FTC (RAIN) 7) Radar Interference Rejection 8) Bearing Marker 9) Heading Line 10) Off Center Manual / Auto Manual / Auto Built-in (The effect can be adjusted by three stages.) 360 in 5 digit Electronic move to the defined coordinates of 4 patterns
(4 patterns are back side 64dots,left side 92dots, front side 92dots, right side 92dots from the default center position) 11) True Motion Unit 12) True Motion Reset Position 13) Radar trail indication Transition of the radar trails is possible during Off Center mode. Built-in (Not available at the maximum range) 40% of radius of any range True motion mode:
Relative motion mode:
Only true motion trails Only relative motion trails Trail time length:
15 sec to 15 min/Continuous 30 sec to 30 min/Continuous 1 min to 1 hr/Continuous 30 min to 12 hr/Continuous Arbitrary trail time length can be displayed at any time. Possible to display time series trail and continuous trail by color classification.
* When switching to true/relative trails, the radar trails are cleared. Transition of the trails is possible during Off Center mode (Relative motion). (Scroll) When the bearing mode is switched (RM (T), TM), the radar trails are taken over at between RM (T) and TM. 168 Chapter 12 SPECIFICATIONS 14) Variety of Pulse width SP1/ SP2/ SP3/ MP1/ MP2/ LP1/ LP2
(LP2 is JMA-1034 only) 15) Target enhance 16) Plotting 17) Display color 3 stages 3 marks Radar echo 16 stages, 8 colors (Yellow, Green, Blue, White, Magenta, Gold, Radar trails 1 stage, Amber, Color) Time trails: 3 colors (Green, Blue, Cyan) Continuous trails: 3 colors (Green, Blue, Cyan) Background Characters AIS/TT EBL/VRM Cursor Own Ship's Range Ring Alarm Zone PPI: 3 colors (Black, Blue, White) 7 colors (White, Cyan, Green, Black, Red, Gold, Amber) 3 colors (Cyan, Green, White) 4 colors (Cyan, Black, Magenta, White) 4 colors (White, Red, Magenta, Yellow) 6 colors (Cyan, Green, Red, White, Gold, Amber) 6 colors (Cyan, Green, Red, White, Gold, Amber) 5 colors (White, Green, Orange, Black, Red) Built-in 18) Simulator 19) Multiple languages English, Spanish, Turkish, Indonesian, Thai, Malay, Vietnamese, Chinese, Russian, Korean, Japanese, Other optional language NM, Km, sm 20) Range Unit 21) Navigation information during STBY 22) AIS information display Built-in
(MMSI, ship name) List display, WPT setting, Can display ship name only 169 Chapter 12 SPECIFICATIONS 12-6-2 OPERATIONAL PANEL 1) Structure Integrated on the display unit 2) Key PWR/CLR Short push: Power ON ( at the time of Power OFF) Long push: Power OFF PWR/CLR Short push: input cancel, back to a up-layer PUSH : Menu or Icon selection and execution, control EBL/VRM, number input, Enter, etc. PUSH + rotation: Brilliance control Tap: Menu or Icon selection and execution, control, etc. Double tap: Brilliance menu Icon Double tap: EBL/VRM disappear Icon Long tap: Entry of short cut Icon 3) Knob Controller 4) Touch control 12-6-3 AIS FUNCTION (STANDARD BUILT IN) 1) Display Number of targets Up to 50 targets (stores up to 500 ship static data) Target information Displays MMSI, call sign, ship name, COG, SOG, CPA, TCPA, direction, distance, latitude, longitude, status, etc. Distance only Not available Filters Active targets Dangerous ship targets No CPA/TCPA decision 2) Operation Built-in 12-6-4 TT FUNCTION (STANDARD BUILT IN) 1) Acquisition 2) Tracking 3) Display MANUAL/AUTO (by automatic acquisition/activation zone) 10 targets (Automatic tracking) 1 ship (AIS or TT) Tracking data Maximum tracking range 20NM (This varies depending on the range) Target information Displays items selected from true bearing, distance, true course, true speed, CPA, TCPA. True/Relative Built-in Display of Vectors 4) Operation 170 12-7 INPUT/ OUTPUT SIGNAL Telecommunications standard NMEA0183 / 61162 -1/2 Chapter 12 SPECIFICATIONS Communications protocol Input sentence Information classification 4800 bps, start 1bit, data 8bit, stop 1bit, non parity NMEA0183: V1,5: GGA/ GLL/ RMC V2,0: GGA/G LL/ RMC/ZDA V2,3 : GGA/GLL/RMC/GNS/ZDA
(Talker=GP etc.) position and time GGA/G NS/G LL/RMC date ZDA/RMC Time ZDA/GGA/GNS/GLL/RMC 12-7-1 INPUT ENABLE SIGNAL
(Three-port input GPS/HDG/AIS)
(1) Navigation equipment IEC61162-1/2(1) GGA>RMC>RMA>GNS>GLL RMC>RMA>VTG VBW>VHW THS>HDT>HDG>HDM DPT>DBT L/L:
SOG/COG:
Log speed:
HEADING:
DEPTH:
WATER TEMP: MTW ROT ROT:
RUDDER:
RSA VDM, VDO, ALR AIS:
MWV>VWT, VWR WIND:
WAYPOINT:
WPL
(2) Bearing signal JRC-NSK format (JLR-10/20/30)(by NMEA3 port) IEC61162-1/2(1) 4800bps/38400bps: THS>HDT>HDG>HDM
(3) Speed signal IEC61162 4800bps: VBW, VHW 1:IEC61162-2 Conformity is unnecessary.
(Insulation is unnecessary. Input electrical tests are unnecessary.) 171 Chapter 12 SPECIFICATIONS 12-7-2 OUTPUT POSSIBLE SIGNAL (THREE-LINE GPS/HDG/TTM)
(1) Navigation equipment Radar date:
RSD Own ships data: OSD TT data:
Latitude/ Longitude data: GGA, RMC, GNS, GLL, COG/SOG:
Bearing signal: THS, HDT (Received GPS Compass data) VTG (Received GPS data) TTM, TTL, TTD
(2) External Buzzer
(3) Output RGB signal Factory presetting: normal open contacts To incorporate optional kit (NQA-2447) is necessary In this case, waterproofing (IPx5) of rear side of display unit is not guaranteed
(4) Slave display
(5) LAN no function no function 12-7-3 STANDARD CONFIGURATION Scanner:
Display Unit:
Sun cover:
Scanner cable:
Power cable:
Standard included accessories:
Instruction /Installation/Quick manual:
1unit 1unit 1unit 1pc. (10m) 1pc. (2m) 1set (2 pieces. fuse) 1 book 12-7-4 OPTION CABLE Scanner cable: 5m, 15m, 20m,30m NMEA cable (waterproof (IPx5)): 1m 172 Chapter 13 APPENDIX Chapter 13 APPENDIX NKE-1066(1.5FT) SCANNER INTRCONNECTION DIAGRAM FIG A1 APPENDIX1 Chapter 13 APPENDIX NKE-2044(2FT) SCANNER INTRCONNECTION DIAGRAM FIG A2 APPENDIX-2 NCD-2256 DISPLAY UNIT INTER CONNECTION DIAGRAM Chapter 13 APPENDIX FIG A3 APPENDIX3 Chapter 13 APPENDIX APPENDIX-4 JMA-1030 PRIMARY POWER SUPPLY DIAGRAM FIG A4 JMA-1030 INTER CONNECTION DIAGRAM Chapter 13 APPENDIX FIG A5 APPENDIX5 Chapter 13 APPENDIX 90mm 140 mm FIG A6 APPENDIX-6 OPERATION SHEET 90mm Chapter 13 APPENDIX GAIN VRM CURSOR TT ACTIV RAIN GURDZONE SETTING TT ST-BY SEA MARK MENU DAY 140 mm BRILLIANCE AIS ACTIV USER1 NIGHT TX-STBY AIS SLEEP USER2 MODE RIVER RANGE MOB MODE STANDARD MODE FIOAT EBL OFFCENTER MODE COAST MODE OFF FIG A7 APPENDIX7 MENU FUNCTION LIST MENU FUNCTION LIST Item Main Menu Setting Contents 1. RADAR Echo 1. Pulse Length 2. IR 3. Target Enhance 4. Process 5. Zoom 6. Video Latitude 7. Video Noise Rejection 8. Timed TX 2. Tuning 3. Motion Mode 1. Motion 2. Bearing Mode 4. Radar trail 1. Trails REF Level 2. Time/All Combine 3. Trails Mode 4. Trails Interval 5. Vector Length 1. Vector Mode 2. Vector Length 6. Maker 1. Maker Mode 2. VRM Unit 3. EBL Bearing Mode 4. Range Rings(RR) 7. Target 1. Function ON/OFF 2. CPA Limit 3. TCPA Limit 1. TT 2. AIS SP/MP/LP OFF / Low / Middle / High OFF / Level1 / Level2 / Level3 OFF / 3Scan COREL / 4Scan COREL / 5Scan COREL / Remain / Peak Hold OFF / ON Narrow / Normal / Wide1 / Wide2 OFF / Level1 / Level2 / Level3 OFF / ON RM, TM HUP/NUP/CUP Level1 / Level2 / Level3 / Level4 OFF / ON True/Relative OFF/15sec/30sec/1min/2min/3min/4min/5min/6min/10min/15min/CONT True/Relative 1 - 60min True/Relative NM/km/sm Heading Fix / Screen Fix OFF / ON OFF / ON OFF / ON 0.1 - 9.9NM 1 - 99min APPENDIX-8 Item Setting Contents MENU FUNCTION LIST 1. TT 2. AIS 4. CPA Ring Display 5. Target Number Display 6. ALR Alarm From AIS 7. AIS Display Targets 8. AIS List Display 8. NMEA Info. Set OFF / ON OFF / ON OFF / ON OFF / ON 20 / 30 / 40 / 50 OFF / ON APPENDIX9 Initial setting Menu Item Setting Contents MENU FUNCTION LIST 1. Basic Adjustment 1. Bearing Adjustment 2. Range Adjustment 3. Tune Adjustment 4. Antenna Height 5. Noise Level 6. Language 1. MBS Level 2. MBS Area 1. RADAR Alarm1 Level 2. RADAR Alarm2 Level 1. STC Curve Select 2. STC Slope Correction 3. STC Offset 2. RADAR Echo 1. Main Bang Suppression 2. Target Enhance Level 3. Gain Preset 4. STC 1. FTC 1. FTC Curve Select 2. FTC Slope Correction 3. FTC Offset 6. RADAR Alarm 3. RADAR Trails 1. MAX Interval 2. Suppression Distance 4. TT 1. Vector Constant 2. Gate Display 3. Gate Size 5. Scanner 1. PRF Fine Tuning 2. Stagger Trigger 3. Antenna Rotation Speed 4. PRF Mode 5. Timed TX 6. Tune Peak Adjustment 7. Tune Indicator Level 6. I/F Device 1. Heading Equipment 2. Manual Heading 3. Speed Equipment 4. Manual Speed 5. MAG Compass Setting 1. Heading Correction 2. Correct Value 1. SP1 2. SP2 3. SP3 4. MP1 5. MP2 6. LP1 7. LP2 (*NKE-2044 only) 1. TX Time 2. STBY Time 3. Adaptation APPENDIX-10 0.0 - 359.9 0 - 999 0 - 127
~5m/5~10m/10~20m/20m~
0 - 255 English/Spanish/Turkish/Indonesian/Thai/Malay/Vietnamese/
Chinese/Japanese/Korean/Russian 0 - 255 0 - 255 Level1/Level2/Level3/Level4 0 - 255 Sea/River 0.0 - 2.0 0 - FF Sea/River 0.0 - 2.0 0 - FF Level1/Level2/Level3/Level4 Level1/Level2/Level3/Level4 Short/Middle/Long/Super Long 0 - 1000 1 - 8 OFF / ON 0 - 64 0 - 31 OFF / ON 0 - 7 0 - 7 0 - 7 0 - 7 0 - 7 0 - 7 0 - 7 Normal/Economy/High Power 1 - 99 1 - 99 ON/OFF 0 127 0 - 127 AUTO/GYRO/Compass/GPS/Manual 0.0 - 359.9 GPS/Log/2axis Log/Manual 0.0 - 100.0kn OFF / ON W9.9 - E9.9 Item Setting Contents MENU FUNCTION LIST 7. COM Port Setting 1. Baud Rate 1. NMEA1 2. NMEA2 3. NMEA3 2. RX Port 1. GPS 2. Log 3. 2axis Log 4. Depth 5. Temperature 6. Wind 7. WPT 8.Rate of Turn 9. Rudder 3. TX Port 1. TTM 2. TLL 3. TTD 4. TLB 5. GGA 6. GLL 7. RMC 8. GNS 9. VTG 10. THS 11. HDT 12. OSD 13. RSD 4. TX Data Format 5. Target Info. TX 8. JRC GPS 1. GPS Status 2. GPS Setting 1. TX Interval 2. NMEA Version 3. NMEA Talker 1. NMEA Version 2. Correction Method 3. Fix Mode 4. Elevate Mask 5. HDOP 6. Smoothing LL 7. Smoothing SOG 8. Smoothing COG 1. TX Target 2. TTM Range Accuracy 3. TT Average Mode 4. TT Average Scan 9. Smoothing 10. Smoothing 11. RAIM Accuracy Level 12. Exclusion Satellite 1. Exclusion Satellite1 2. Exclusion Satellite2 3. Exclusion Satellite3 4. Exclusion Satellite4 5. Exclusion Satellite5 6. Exclusion Satellite6 AUTO/4800bps/38400bps AUTO/4800bps/38400bps AUTO/4800bps/38400bps AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 AUTO/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 OFF/NMEA1/NMEA2/NMEA3 1 - 9sec V1.5/V2.0/V2.3 Normal/GP TT/AIS/TT-AIS 1/2/3 OFF / ON 2 - 10 AUTO/V1.5/V2.0/V2.3 GPS Single/SBAS/Beacon/AUTO 2D/3D/AUTO 5 - 89 4/10/20 0 - 99sec 0 - 99sec 0 - 99sec 0 - 99sec (R29.04 - R33.99) 1 - 99sec (R26.01 - R29.03) 0sec/10sec/40sec OFF/10/30/50/100m 0 - 32 0 - 32 0 - 32 0 - 32 0 - 32 0 - 32 APPENDIX11 MENU FUNCTION LIST Item Setting Contents 1. Position 2. Antenna Height 3. Time 4. Date 5. Master Reset 6. Send Data 1. Satellite Search 2. Ranging 3. SBAS Satellite Number 4. Send Data 1. Key ACK 2. Operation Error 3. CPA/TCPA 4. AZ/Alarm Zone 5. Target Lost 6. System Alarm 13. Send Data 14. GPS Adjust 3. Beacon Setting 1. Station Select 2. Frequency 3. Baud Rate 4. Send Data 4. SBAS Setting 9. Control 1. Touch Panel Calibration 2. Bearing Reference (*NKE-2044 only) 3. Buzzer 10. Maintenance 1. Partial Reset 1. All Menu 2. RADAR Echo 3. Function Setting 4. Initial Setting Menu 5. Main Menu 6. Adjust Menu (*NKE-2044 only) 7. System Information 1 (*NKE-2044 only) 8. System Information 2 (*NKE-2044 only) 2. All Reset 3. System Time Clear 4. Scanner Time Clear 5. Table Update 1. Initial Value 1. TX Time Clear 2. Motor Time Clear 3. ANT to DISP Unit 4. DISP to ANT Unit 2. Insert Language 3. Echo Simulation (*NKE-2044 only) 4. STC Curve 5. Color Pallet (*NKE-2044 only) 1. All Menu 2. RADAR Echo 3. Function Setting 4. Initial Setting Menu 5. Main Menu 6. Adjust Menu
(*NKE-2044 only) 7. System Information 1
(*NKE-2044 only) 8. System Information 2
(*NKE-2044 only) 0 - 8191m 00:00:00 - 23:59:59 2013/1/1/ - 2099/12/31 AUTO/Manual 283.5 - 325.0kHz 50 / 100 / 200bps AUTO/Manual OFF / ON 120 - 138 True/Relative OFF/1 - 5 OFF/1 - 5 OFF/1 - 5 OFF/1 - 5 OFF/1 - 5 OFF/1 5 APPENDIX-12 Item Setting Contents MENU FUNCTION LIST 6. Internal Setting 1. Internal Memory to USB 2. USB to Internal Memory 1. Ship's Move Method 1. All Length 2. All Width 3. Scanner (from Bow) 4. Scanner (from Cntr.) 1. Range 2. Distance 3. Speed 4. Depth 5. User Depth 6. Temperature 7. Wind 7. USB Format 11. System Setting 1. Master/Slave/DEMO 2. Own Ship Outline 3. Unit 4. Move Own Ship 5. Range 1. NM 1. All Menu 2. RADAR Echo 3. Function Setting 4. Initial Setting Menu 5. Main Menu 6. Mark Setting 7. Adjust Menu
(*NKE-2044 only) 8. System Information 1
(*NKE-2044 only) 9. System Information 2
(*NKE-2044 only) 1.All Menu 2. RADAR Echo 3. Function Setting 4. Initial Setting Menu 5. Main Menu 6. Mark Setting 7. Adjust Menu
(*NKE-2044 only) 8. System Information 1
(*NKE-2044 only) 9. System Information 2
(*NKE-2044 only) Master/Slave/Demo 0.0 - 600.0m 0.0 - 200.0m 0.0 - 600.0m
-100.0 100.0m NM/km/sm NM/km/sm kn/ km/h /mph ft/fm/m/user 0.1 - 10.0 C /F m/s / km/h / kn / Bft. LL / COG/SOG OFF / ON 1. 0.0625NM OFF / ON 2. 0.125NM OFF / ON 3. 0.25NM 4. 0.5NM (*NKE-2044 only) OFF / ON 5. 0.75NM (*NKE-2044 only) OFF / ON OFF / ON 4. 1NM OFF / ON 5. 2NM OFF / ON 6. 4NM 7. 8NM OFF / ON OFF / ON 8. 16NM OFF / ON 9. 24NM OFF / ON 10. 32NM 11. 48NM OFF / ON APPENDIX13 MENU FUNCTION LIST Item Setting Contents 1. 0.15km 2. 0.3km 3. 0.5km (*NKE-2044 only) 4. 1.2km 5. 2km 6. 8km 7. 16km 8. 32km 1. 0.0625sm 2. 0.125sm 3. 0.25sm 4. 1sm 5. 2sm 6. 4sm 7. 8sm 8. 16sm 9. 24sm 10. 32sm 11. 48sm 2. km 3. sm 12. Display Screen 1. Own Vector Display 2. STBY Disp. Select 3. Operation Num Disp. 4. Display Color 1. PPI 2. Inner PPI (*NKE-2044 only) 1. Color 2. Brilliance 1. Color
(*NKE-2044 only) 2. Brilliance
(*NKE-2044 only) 3. Character 4. RADAR Echo 5. RADAR Trails (Time) 6. RADAR Trails (All) 7. Own Ship's 8. Target (TT/AIS) 9. EBL/VRM 10. Range Ring 11. Cursor 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance 1. Color 2. Brilliance APPENDIX-14 OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON OFF / ON Normal / Graphical / Numeric Display OFF / ON Black/ Blue/ White Level1/ Level2/ Level3/ Level4 Black/ Blue/ White Level1/ Level2/ Level3/ Level4 White/Cyan/Green/Black/Red/Gold/Amber Level1/ Level2/ Level3/ Level4 Yellow/Green/Blue/White/Magenta/Gold/Amber/Color Level1/ Level2/ Level3/ Level4 Green/Blue/Cyan Level1/ Level2/ Level3/ Level4 Green/Blue/Cyan Level1/ Level2/ Level3/ Level4 Cyan/Green/Red/White/Gold/Amber Level1/ Level2/ Level3/ Level4 Cyan/Green/White Level1/ Level2/ Level3/ Level4 Cyan/Black/Magenta/White Level1/ Level2/ Level3/ Level4 Cyan/Green/Red/White/Gold/Amber Level1/ Level2/ Level3/ Level4 White/Red/Magenta/Yellow Level1/ Level2/ Level3/ Level4 Item Setting Contents MENU FUNCTION LIST 1. Color 2. Brilliance 12. AZ/Alarm Zone 1. Scanner(Time Out) 2. Scanner(Data) 3. Scanner(Video) 4. Scanner (Trigger) 5. Scanner(AZI) 6. Scanner(HL) 7. Scanner(MHV) 8. Scanner(Heater) 5. Waypoint Display 6. AIS Filter 13. Error Alarm Mask 1. Scanner 2. Display Unit 3. Connection Device (*NKE-2044 only) 1. Display Unit(Video) 2. Display Unit(Trigger) 3. Display Unit(AZI) 4. Display Unit(HL) 5. Display Unit(DSP) 6. COM Port 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 1. GYRO(Time Out) (*NKE-2044 only) White/Green/Orange/Black/Red Level1/ Level2/ Level3/ Level4 ON/OFF 0.0 - 48.0 OFF / ON 0 - 999sec OFF / ON 0 999sec OFF / ON 0 - 999sec OFF / ON 0 - 999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 1. Alarm Sensitivity
(*NKE-2044 only) 2. Sensitivity Time
(*NKE-2044 only) 2. Log(Time Out) (*NKE-2044 only) 1. Alarm Sensitivity
(*NKE-2044 only) 2. Sensitivity Time
(*NKE-2044 only) 3. GPS(Time Out) (*NKE-2044 only) 1. Alarm Sensitivity
(*NKE-2044 only) 2. Sensitivity Time
(*NKE-2044 only) OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec APPENDIX15 MENU FUNCTION LIST Item Setting Contents 4. RX Data 1. GYRO 2. Compass 3. Log 4. 2Axis Log 5. Course/Speed 6. Depth 7. Temperature 8. Wind 9. Rate of Turn 10. Rudder 11. WPT 12. LAT/LON 13. Datum 14. Status 15. HDOP 16. AIS 14. Test 1. System Information APPENDIX-16 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Alarm Sensitivity 2. Sensitivity Time 1. Indicator Software 2. Boot 3. DSP (MC) 4. DSP (V) 5. Test Bench 6. Scanner Software 7. Update OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec OFF / ON 0 -999sec 1.0.0 01.06 01.00.00.00 01.00.00.00 01.04 04.02 01.06 2. System Time 3. Scanner Information 4. Hardware Information 5. Error Log 1. Display 2. Erase 6. Line Monitor 7. Self Test 1. Key Test 2. Touch Panel Test 3. Buzzer Test 4. Key Light Test 5. Monitor Display Test 6. Memory Test 7. Line Test 8. Scanner Test Item Setting Contents MENU FUNCTION LIST 1. Scanner Transmit Time 2. Scanner Motor Time 3. Scanner Running Time 4. Indicator Running Time 1. Scanner Transmit Power 2. Motor Type 3. Magnetron Current 1. Serial Number 2. MAC Address 1. Scanner 2. NMEA1 3. NMEA2 4. NMEA3 Pattern1 Pattern2 Pattern3 Pattern4 Pattern5 Pattern6 Pattern7 RGB Setting Red Green Blue Display 1. SDRAM 2. Flash ROM 3. USB 1. Scanner 2. NMEA1 or GPS(JRC) 3. NMEA2 4. NMEA3 or NSK 1. SSW Off 2. BP 3. BZ 4. Mod.HV 5. Trigger 6. Video APPENDIX17 MENU FUNCTION LIST APPENDIX-18 Not use the asbestos JRC website http://www.jrc.co.jp/
Marine Service Department Telephone: +81-3-3492-1305 Facsimile: +81-3-3379-1420 e-mail tmsc@.jrc.co.jp Amsterdam branch Telephone: +31-(0)20-658-0750 Facsimile +31-(0)20-658-0755 e-mail service@jrceurope.com Seattle branch Code No.7ZPRD0895 01JTM Telephone: +1-(0)206-654-5644 Facsimile: +1-(0)206-654-7030 e-mail service@jrcamerica.com ISO 9001 and ISO 14001 Certified Dec, 2013 creation The 1st edition JRC
This product uses the FCC Data API but is not endorsed or certified by the FCC