| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 650.83 KiB | ||||
| 1 | Cover Letter(s) | |||||||
| 1 | RF Exposure Info | |||||||
| 1 | Internal Photos | |||||||
| 1 | ID Label/Location Info | |||||||
| 1 | Test Report | |||||||
| 1 | External Photos |
| 1 | User Manual | Users Manual | 650.83 KiB |
HPT225BT*
VHF Modem Operators Manual Version 1.2 Last Revised December 17, 2012 All rights reserved.The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written All contents in this manual are copyrighted by JAVAD GNSS. consent from JAVAD GNSS HPT225, AW225BT, and AW225 are other names for marketing purpose JAVAD GNSS Inc., 2012 www.javad.com TABLE OF CONTENTS Preface . 5 Terms and Conditions. 5 Regulatory Information . 7 Manual Conventions. 8 Screen Captures . 8 Technical Assistance . 9 Chapter 1. Introduction. 11 1. Getting Acquainted. 12 1.1. LEDs. 12 1.2. Data and Power Ports . 12 1.3. External Antenna and Bluetooth Antenna Connectors. 13 1.4. Mounting Bracket. 13 1.5. Cables . 13 1.6. Literature . 14 1.7. External Antenna (not included) . 14 1.8. Storage Precautions . 14 Chapter 2. Configuration . 15 1. Powering HPT225BT . 15 1.1. Power supply requirements . 15 2. Antenna Installation . 16 3. Installing ModemVU . 16 4. Connecting HPT225BT and Computer . 17 4.1. Connecting through serial port . 17 4.2. Connecting through USB port . 17 4.3. Connecting through Bluetooth . 18 5. Configuring HPT225BT . 19 5.1. Simplex Protocol . 20 5.2. Half-Duplex Protocol . 21 6. Checking Firmware Version. 22 7. Loading New Firmware . 23 8. Bluetooth Configuration . 25 www.javad.com 3 Chapter 3. Command Line Interface. 27 1. Command Line Interface Convention . 28 1.1. Software Switching to Command Mode . 28 1.2. Hardware Switching to Command Mode . 29 1.3. Switching to Data Mode . 29 2. Networking Commands . 30 2.1. LINK . 30 3. Serial Interfacing Commands . 31 3.1. DPORT . 31 3.2. MPORT . 32 4. Special Commands . 33 4.1. BOOT . 33 4.2. HELP . 33 4.3. SAVE. 33 4.4. SLEEP . 34 5. Diagnostics and Identification Commands . 34 5.1. INFO . 34 5.2. STATE. 35 Appendix A. Specifications . 37 1. HPT225BT VHF Modem Specifications. 37 1.1. General Radio Specifications . 37 1.2. Environmental Specifications . 38 1.3. Transmitter Specifications. 39 1.4. Receiver Specifications . 39 2. Compliance . 40 3. Connector Specifications . 40 Appendix B. Safety Warnings. 43 1. General Warnings . 43 Appendix C. VHF Radio Usage . 45 Appendix D. Warranty Terms . 47 4 www.javad.com PREFACE Thank you for purchasing this product. The materials available in this Manual (the Manual) have been prepared by JAVAD GNSS, Inc. (JAVAD GNSS) for owners of JAVAD GNSS products. It is designed to assist owners with the use of HPT225BT and its use is subject to these terms and conditions (the Terms and Conditions). Note: Please read these Terms and Conditions carefully. Terms and Conditions USE JAVAD GNSS modems are designed to be used by a professional. The user is expected to have a good knowledge and understanding of the user and safety instructions before operating, inspecting or adjusting. COPYRIGHT All information contained in this Manual is the intellectual property of, and copyrighted material of JAVAD GNSS. All rights are reserved. You may not use, access, copy, store, display, create derivative works of, sell, modify, publish, distribute, or allow any third party access to, any graphics, content, information or data in this Manual without JAVAD GNSS express written consent and may only use such information for the care and operation of your HPT225BT. The information and data in this Manual are a valuable asset of JAVAD GNSS and are developed by the expenditure of considerable work, time and money, and are the result of original selection, coordination and arrangement by JAVAD GNSS. TRADEMARKS HPT225BT, TRIUMPH-1, ModemVU, JAVAD GNSS are trademarks or registered trademarks of JAVAD GNSS. Windows is a registered trademark of Microsoft Corporation;
Bluetooth word mark is owned by the Bluetooth SIG, Inc. Product and company names mentioned herein may be trademarks of their respective owners. DISCLAIMER OF WARRANTY EXCEPT FOR ANY WARRANTIES IN THIS MANUAL OR A WARRANTY CARD ACCOMPANYING THE PRODUCT, THIS MANUAL AND THE HPT225BT MODEM ARE PROVIDED AS-IS. THERE ARE NO OTHER WARRANTIES. JAVAD GNSS DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE. JAVAD GNSS AND ITS DISTRIBUTORS SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;
NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE OR USE OF THIS MATERIAL OR THE HPT225BT MODEM. SUCH DISCLAIMED DAMAGES INCLUDE BUT ARE NOT LIMITED TO LOSS OF TIME, LOSS OR DESTRUCTION OF DATA, LOSS OF PROFIT, SAVINGS OR REVENUE, OR LOSS OF THE PRODUCT'S USE. IN ADDITION, JAVAD GNSS IS NOT RESPONSIBLE OR LIABLE FOR DAMAGES OR COSTS INCURRED IN CONNECTION WITH OBTAINING SUBSTITUTE PRODUCTS OR SOFTWARE, CLAIMS BY OTHERS, INCONVENIENCE, OR ANY OTHER www.javad.com 5 Preface Terms and Conditions COSTS. IN ANY EVENT, JAVAD GNSS SHALL HAVE NO LIABILITY FOR DAMAGES OR OTHERWISE TO YOU OR ANY OTHER PERSON OR ENTITY IN EXCESS OF THE PURCHASE PRICE FOR HPT225BT. LICENSE AGREEMENT Use of any computer programs or software supplied by JAVAD GNSS or downloaded from a JAVAD GNSS website (the Software) in connection with HPT225BT constitutes acceptance of these Terms and Conditions in this Manual and an agreement to abide by these Terms and Conditions. The user is granted a personal, non-exclusive, non-transferable license to use such Software under the terms stated herein and in any case only with a single HPT225BT or single computer. You may not assign or transfer the Software or this license without the express written consent of JAVAD GNSS. This license is effective until terminated. You may terminate the license at any time by destroying the Software and Manual. JAVAD GNSS may terminate the license if you fail to comply with any of the Terms or Conditions. You agree to destroy the Software and manual upon termination of your use of HPT225BT. All ownership, copyright and other intellectual property rights in and to the Software belong to JAVAD GNSS. If these license terms are not acceptable, return any unused software and manual. CONFIDENTIALITY This Manual, its contents and the Software (collectively, the Confidential Information) are the confidential and proprietary information of JAVAD GNSS. You agree to treat JAVAD GNSS' Confidential Information with a degree of care no less stringent that the degree of care you would use in safeguarding your own most valuable trade secrets. Nothing in this paragraph shall restrict you from disclosing Confidential Information to your employees as may be necessary or appropriate to operate or care for HPT225BT. Such employees must also keep the Confidentiality Information confidential. In the event you become legally compelled to disclose any of the Confidential Information, you shall give JAVAD GNSS immediate notice so that it may seek a protective order or other appropriate remedy. WEBSITE; OTHER STATEMENTS No statement contained at the JAVAD GNSS website (or any other website) or in any other advertisements or JAVAD GNSS literature or made by an employee or independent contractor of JAVAD GNSS modifies these Terms and Conditions (including the Software license, warranty and limitation of liability). SAFETY Improper use of HPT225BT can lead to injury to persons or property and/or malfunction of the product. The HPT225BT modem should only be repaired by authorized JAVAD GNSS warranty service centers. Users should review and heed the safety warnings in Appendix C. MISCELLANEOUS The above Terms and Conditions may be amended, modified, superseded, or canceled, at any time by JAVAD GNSS. The above Terms and Conditions will be governed by, and construed in accordance with, the laws of the State of California, without reference to conflict of laws. 6 www.javad.com Preface Regulatory Information Regulatory Information There are two modes implemented by firmware for the North America: <US MODE> and <CANADA MODE>.
<US MODE> is preloaded/preprogrammed at the factory for HPT225BT VHF Transceiver sold to US customers.
<CANADA MODE> is preloaded/preprogrammed at the factory for HPT225BT VHF Transceiver sold to customers in Canada. The selection is not available to the customer. FCC Class A Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment. Canadian Emissions Labeling Requirements This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe A respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Industry Canada The term IC: before the equipment certification number only signifies that the Industry Canada technical specifications were met. WEEE Directive The following information is for EU-member states only: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could www.javad.com 7 Preface Manual Conventions the take-back and recycling of this product, please contact your supplier where you purchased the product or consult. Manual Conventions This manual uses the following conventions:
Example FileExit Link Space Temp Click the File menu and click Exit Description This format represents titles of dialog windows/boxes, names of menu options, identifies program interface objects, such as checkboxes, edit boxes, radio buttons, etc. This format is used to enter various string information (e.g., file and directory names) as well as operator commands. Screen Captures This manual includes sample screen captures. Your actual screen can look slightly different from the sample screen due to the modem you have connected, operating system used and settings you have specified. This is normal and not a cause for concern. 8 www.javad.com Preface Technical Assistance Technical Assistance If you have a problem and cannot find the information you need in the product documentation, contact your local dealer. Alternatively, request technical support using the JAVAD GNSS World Wide Web site at: www.javad.com. www.javad.com 9 Preface Technical Assistance 10 www.javad.com Chapter 1 INTRODUCTION External extra rugged digital high power VHF radio transceiver programmable in frequency ranges from 215 to 255 MHz. The HPT225BT provides half-duplex communication with transmitter output power of 2 W in the frequency band 217 - 220 MHz and 25 W in the frequency band 220 - 222 MHz for USA; 25 W the frequency bands 217 - 218 MHz, and 219 - 220 MHz, 220 - 222 MHz for Canada. It has GMSK, DBPSK, DQPSK, 4FSK, D8PSK, and D16QAM modulations with advanced forward error correction and data scrambling. The output power is programmable from 320 mW to 25 W. Figure 1. HPT225BT The HPT225BT radio transceiver provides a high-speed Point-to-Point and Point-to-Multipoint wireless data transfer at up to 38.4 kbps. HPT225BT supports user selectable modulation techniques (GMSK, 4FSK, DBPSK, DQPSK, D8PSK, or D16QAM), which allows the user to achieve the highest data speed for a given range (up to 48 miles / 77 km). It also includes a selectable error correction, which improves the functioning of the radio modem under interference. The sophisticated features of HPT225BT include data scrambling, frequency hopping, user selectable transmit output power level, low power consumption sleep modes, autoscannin and plug-and-play installation for remote terminals. The built-in software tools provide the wireless link testing, units status and error statistics monitoring as well as units settings change over the air. The firmware of the HPT225BT radio transceiver resides in a flash memory. The updating of the radio modem programs is entirely software-based. The flash memory is re-programmable through an RS232 interface, USB, Bluetooth, or over the air. The units user settings can be changed through the built-in Command Line interface (CLI), Tracy Software or through ModemVU. www.javad.com 11 Introduction Getting Acquainted 1. Getting Acquainted The HPT225BT is a rugged and very powerful external radio transceiver 152 mm wide 84 mm deep 72 mm high, weighs 900 g. 1.1. LEDs External LED's (see Figure 2) are used for Link and Line status indication:
Positio n LED Name PWR SYNC Color Green Red Green TX/RX ALARM Red 1 2 3 4 Description Active if Power connected to modem Active whenever a signal with a level sufficient for reliable reception exists on the radio channel. Active if modem receives or transmits Data over serial interface Active if modem receives or transmits Data over Bluetooth 1.2. Data and Power Ports The HPT225BT data and power port are placed on the front of the unit (Figure 2). LEDs Data port Power port Figure 2. HPT225BT front side Through the data port the HPT225BT modem can be connected to RS-232 serial port with Data-Ser Cable, DB9/DB15 (6ft/1.8m), or this port can be configured as RS422/485 and connected to the RS-422 or RS-485 ports. With Data-Ser Cable, ODU-7/DB15 (6ft/1.8m) the modem can be connected to the JAVAD GNSS receiver. Through the power port the HPT225BT modem can be powered. See Powering HPT225BT on page 15 for detailed information. 12 www.javad.com Introduction Getting Acquainted 1.3. External Antenna and Bluetooth Antenna Connectors The external antenna connects to the BNC external antenna connector and Bluetooth antenna connects to the SMA connector which are placed on the back panel of HPT225BT. Bluetooth Antenna External Antenna Figure 3. External and Bluetooth Antenna Connectors 1.4. Mounting Bracket The mounting bracket (Figure 4) connects the modem to a standard pole/adapter (Figure 4). Mounting Bracket Figure 4. Mounting Bracket 1.5. Cables The HPT225BT package includes standard communication and power cables for configuring the modem and providing a power source to the modem. Data-Ser Cable, ODU-7/DB15 (6ft/1.8m) p/n 14-578108-01 Data-Ser Cable, DB9/DB15 (6ft/1.8m) p/n 14-578110-01 Power Cable, PL-700/Battery Clips (8.2 ft./2.5m) p/n 14-578111-01 www.javad.com 13 Introduction Getting Acquainted 1.6. Literature HPT225BT literature, including manuals and other product information are available on the JAVAD GNSS website (http://www.javad.com):
HPT225BT Operators Manual
Functional specifications 1.7. External Antenna (not included) Antenna type depends on the site requirements, and may be directional or omni-directional. Warning: Do not use HPT225BT without antenna our attenuator to avoid serious damage of your device. 1.8. Storage Precautions 1. Always clean the instrument after use. Wipe off dust with a cleaning brush, then wipe off dirt with a soft cloth. 2. Store in a location with a temperature of -40... +85C, and no exposure to direct sunlight. 3. Use a clean cloth, moistened with a neutral detergent or water, to clean the modem. Never use an abrasive cleaner, ether, thinner benzene, or other solvents. Always make sure the instrument is completely dry before storing. Dry the modem with a soft, clean cloth. 14 www.javad.com Chapter 2 CONFIGURATION 1. Powering HPT225BT To power HPT225BT use the Battery kit 2 (p/n 99-587100-10). Figure 1. Battery Kit 2 Warning: Powering HPT225BT please observe polarity!
1.1. Power supply requirements A single external power supply is necessary to operate HPT225BT. The external power supply needs to be Listed for US and Certified for EU countries, it needs also to be a Limited Power Source and rated for Outdoor Use and have an output rated for +9... +16V, 10A. This may not be the same range as other JAVAD GNSS products with which you are familiar. CAUTION: To avoid the introduction of hazards when operating and installing, before connecting of the equip-
ment to the supply, make sure that the supply meets local and national safety ordinances and matches the equipments voltage and current requirements. CAUTION: Never attempt any maintenance or cleaning of the supply while plugged in. Always remove supply from AC power before attempting service or cleaning. Warning:
If the voltage supplied is below the minimum specification, the modem will suspend operation. If the voltage supplied is above the maximum specification, the modem may be permanently damaged, voiding your warranty. Make sure cords are located so that will not be stepped on, tripped over, or otherwise subjected to damage or stress. Do not operate equipment with a damaged cord or plug replace immediately. www.javad.com 15 Configuration Antenna Installation To reduce the risk of damage to the equipment, pull by the plug body rather than the output cord when disconnecting the equipment. Do not operate the supply if it has received a sharp blow, been dropped, or otherwise damaged. Do not disassemble the supply. Warning: Before connecting the external power source and the modem, make sure that the power source matches the modems voltage and current requirements. 2. Antenna Installation Warning: To avoid the equipment serious damage, do not switch the modem to transmit mode if RF antenna is not connected!
Select the type of antenna that best fits your application and the one that offers the highest dB gain. In addition, setup your system in the highest possible location to minimize obstacles between the transmitting and receiving systems. Always place the antenna on the highest point available. At a minimum, set the antenna to at least ten feet above the terrain using an antenna mast. Use coaxial cable and connectors that are impedance-matched with the radio equipment, and make sure to use the shortest length of cable to move the signal between the radio and the antenna. 3. Installing ModemVU ModemVUTM is a Windows application is a configuration program for the radio modem. ModemVU is available from the JAVAD GNSS website. Note: Refer to the ModemVU Software Manual for full details on installing and using ModemVU Software. ModemVU is JAVAD GNSSs configuration utility for external modems and modems embedded in JAVAD GNSS modems. ModemVU provides the following functions:
Connecting a computer to an VHF modem via a serial port.
Displaying information about the radio modem installed in the modem.
Programming the radio modems settings.
Loading the new modem firmware. To configure the HPT225BT modem, have the following ready:
Computer running Windows;
ModemVU Software installed on the computer;
A serial cable. 1. If downloading the program from the website, extract the program files into a folder on your hard drive. 2. Navigate to the location of the ModemVU program and double-click the Setup.exe icon. 16 www.javad.com Configuration Connecting HPT225BT and Computer 3. Follow the on-screen installation instructions. Click Next to continue, Back to get back to previous step, or Cancel to quit the installation. 4. Keep the default installation location or select a new location. 5. Click Finish to complete the installation. 6. If desired, create a shortcut on the computers desktop for quick access to ModemVU. To uninstall ModemVU use the Start menu on your computer:
1. Navigate to the location of the ModemVU program and double-click the Setup.exe icon. 2. Follow the on-screen installation instructions. 4. Connecting HPT225BT and Computer Once you have established a connection between the modem and the computer, you will be able to:
Configure the modem and its components
Send commands to the modem Use ModemVU to load new firmware to the modem. 4.1. Connecting through serial port To configure, or maintain HPT225BT, you need to connect the modem and a computer using RS-232, RS-422/4851 ports with Data-Ser Cable, DB9/DB15 (6ft/1.8m) p/n 14-578110-01 and start ModemVU. Figure 2. Data-Ser Cable, DB9/DB15 4.2. Connecting through USB port Make sure the computer has special USB driver installed (available from www.javad.com) before continuing. To configure, or maintain HPT225BT using USB port, you need to connect the modem and a 1. To have additional information how to configure serial port as RS-422 or RS-485, please contact JAVAD GNSS customer support using QUESTIONS System at www.javad.com www.javad.com 17 Configuration Connecting HPT225BT and Computer computer using special cable (not included in the standard kit) Access Data-Ser Cable, USB/DB15
(1,8m) (p/n 14-578123-01). Figure 3. Cable p/n 14-578123-01 1. Download the zip-archive with USB driver from www.javad.com;
2. Extract the archive to the new empty folder;
3. Connect the USB port of the computer to the USB port of the modem at the switched off power supply by using of a cable. 4. Turn on your computer. 5. Power HPT225BT. 6. Widows will detect USB driver automatically. Otherwise it will ask to specify driver location. Select the folder with extracted file. 4.3. Connecting through Bluetooth Note: Do not forget to attach the Bluetooth antenna to Bluetooth antenna connector on the back panel of the modem. The HPT225BT modem contains Bluetooth wireless technology that allows synchronization between the modem and any other external device that supports Bluetooth wireless technology. HPT225BT and external device connection procedure varies slightly depending on the type of external device used. In general, the connection procedure is as follows:
Note: Refer to your Bluetooth-enabled external device documentation for more detailed connection information. 1. Turn on a Bluetooth-enabled external device and your receiver. The default external device mode is Master; the modems Bluetooth module mode is Slave. Instruct the external device (Master) to search for the modem (Slave). 2. 3. Once the Master device detects the modem, use the procedure described in the external devices documentation to connect it with the modem. 18 www.javad.com Configuration Configuring HPT225BT 5. Configuring HPT225BT 4. Connect the computer and HPT225BT, as described in Connecting HPT225BT and Computer on page 17. 5. Turn on the modem. 6. Start ModemVU. 7. Select the HPT225BT (Figure 4) in the Options window, and click OK:
8. Select the COM port the HPT225BT modem is connected to (Figure 5). Click Connect. Figure 4. Options window Figure 5. Connect to ModemVU www.javad.com 19 Configuration Configuring HPT225BT 5.1. Simplex Protocol When the HPT225BT modem is loaded with special firmware which supports Simplex protocol1, the ModemVU general window will be like below:
Figure 6. Radio Link tab. Simplex protocol 1. On the Radio Link tab, set the following parameters (Table 1) and click Apply. Table 1. Modem Parameters for the Radio Link Tab Parameter Base Modem Repeater Rover Modem Protocol Mode receiver/
Echo to serial port Simplex Repeater Simplex Transmitter or Simplex Transmitter to Repeater For Base, Repeater, and Rover modems the protocol type must be the same.
Simplex Receiver ON- enables echoing to serial port;
OFF - disables echoing to serial port Auto - allows receiving data from base and repeater in auto mode1. Only from Repeater - allows receive data only from repeater2. Only from transmitter to Repeater - allows receive data from base transmitter3. Frequency Output power Set the frequency in band 215-255 MHz with 6.25 kHz channel spacing. For both Base and Rover modems the frequency must be the same. Select the transmission power for the radio modem. n/a 1. Simplex protocol is a communications protocol that is purely one-way, and where acknowledgments are not part of any application protocol. 20 www.javad.com Configuration Configuring HPT225BT Parameter Modulation type Link Rate Link Space Forward Error Correction Scrambling Base Modem Repeater Rover Modem Specifies a modulation scheme that will be used by your modem. DQPSK is recommended. For both Base and Rover modems the modulation type must be the same. The link rate is selected automatically For both Base and Rover modems the link space must be the same. Enable Enable Enable Enable 1. In Auto mode rover receives the data from both base transmitter and repeater. The sophisticated algo-
rithm of data receiving allows the modem to eliminate any data doubling. 2. In this mode the incoming data from base transmitter will be ignored. 3. In this mode the incoming data from repeater will be ignored. 2. When finished, click FileDisconnect. 5.2. Half-Duplex Protocol When the HPT225BT modem is loaded with special firmware which supports Half-duplex protocol1, the ModemVU general window will be like below:
1. On the Radio Link tab, set the following parameters (Table 1) and click Apply:
Figure 7. Radio Link tab. Half-duplex protocol 1. Half-duplex (HDX) operation means such operation in which communication between two terminals occurs in either direction, but in only one direction at a time. www.javad.com 21 Configuration Checking Firmware Version Parameter Protocol Frequency Output power Modulation type Link Rate Link Space Forward Error Correction Enable Scrambling Enable Mode Half-duplex Base or Half-duplex Remote For Base, Repeater, and Removed modems the protocol type must be the same. Set the frequency in band 215-255 MHz with 6.25 kHz channel spacing. For both Base and Rover modems the frequency must be the same. Select the transmission power for the radio modem. Specifies a modulation scheme that will be used by your modem. DQPSK is recommended. For both Base and Rover modems the modulation type must be the same. The link rate is selected automatically For both Base and Remote modems the link space must be the same. 6. Checking Firmware Version Use ModemVU to check the firmware version of your HPT225BT. 1. Connect your modem and computer. See Connecting HPT225BT and Computer on page 17 for this procedure. 2. Start ModemVU. Select the HPT225BT and than the COM port and click Ok (see Configuring HPT225BT on page 19). 3. Click on Identification tab (Figure 8). This tab lists important information about the hardware accessories and software properties. Figure 8. Identification tab 22 www.javad.com Configuration Loading New Firmware 4. Click FileDisconnect, then FileExit to quit ModemVU. 7. Loading New Firmware The modem uses ModemVU to load firmware onto the modem. For more information, refer to the ModemVU Software Manual, available on the JAVAD GNSS website. 1. Download the new firmware package to your computer. 2. Connect your modem and computer, as described in Connecting HPT225BT and Computer on page 17. 3. Start ModemVU. Select the HPT225BT and than the COM port and click Ok (see Configuring HPT225BT on page 19). 4. Click the Serial Interface &Tools tab;
5. Click Download Firmware button (Figure 9). Figure 9. Serial Interface & Tools tab www.javad.com 23 Configuration Loading New Firmware 6. Open the required firmware folder. Select the .xmd file and click OK (Figure 10):
Figure 10. Load New Firmware 7. Wait until the new firmware version process will be complete. 8. Click FileDisconnect, then FileExit to quit ModemVU. 24 www.javad.com 8. Bluetooth Configuration1 Bluetooth module of HPT225BT can be configured in the BT tab (Figure 11). Configuration Bluetooth Configuration Figure 11. BT tab Use the BT drop down list to switch on/off the module. The PIN code can be inserted in the PIN code field. Click Apply to save settings and apply configurations. 1. Now is supported for Simplex mode only www.javad.com 25 Configuration Bluetooth Configuration 26 www.javad.com Chapter 3 COMMAND LINE INTERFACE The built-in user-friendly Command Line Interface (CLI) allows user to perform a full configuration of the unit and read the statistics and alarm status. It is the most powerful tool to configure the unit. It makes changes to all possible settings that system will not be able to determine automatically. The CLI commands allow user to configure and reconfigure the units settings. The user configuration parameters that could be changed through the CLI are:
Data Port Settings
- Baud Rate
- Data Bits (8, 7)
- Parity (Odd, Even, None)
- Flow control (None or RTS/CTS)
Alarm Settings
Radio Operation Modes
Sleep modes
- On/Off
- Activate by internal real-time clock
- Activate through RTS/CTS lines
- Activate by external sense lines
- Activate by any combination of the parameters mentioned before Note: The units configuration that is set or modified through the CLI will be lost after units reboot, unless the saving operation is used to store a new setting in the units configuration file. The CLI commands also provide filing operations, which include:
Downloading
- Units Configuration files
- Software Images
Uploading Units Configuration files
Saving into the configuration files the configuration parameters modified through the CLI. www.javad.com 27 Command Line Interface Command Line Interface Convention 1. Command Line Interface Convention The following convention is implemented in HPT225BT Command Line Interface (CLI):
The Carriage Return/Line Feed (CR/LF, 0x0D/0x0A) is a command delimiter.
The Carriage Return/Line Feed (CR/LF, 0x0D/0x0A) is a reply delimiter followed by the CLI>
prompt if Echo option is On.
The Carriage Return/Line Feed (CR/LF, 0x0D/0x0A) is a reply delimiter if Echo option is Off
(default option).
The 2-digit number followed by @ in the unit's reply indicates the error code (refer to Table 3 for description), if Echo Off is selected, otherwise the error message is displayed.
A successfully performed command is replied by @00 code, if Echo Off is selected, otherwise the set value is replied.
A command with the certain [Parameter Name] and blank [Parameter List] displays the current settings for a given parameter.
To set the mode ordered by CLI commands as permanent User Setting (the setting automatically selected for the boot-up unit) the SAVE command must be asserted.
A command followed by /F option displays the Parameters in the predefined frame format. The display frame format is unique for each command supporting /F option. Table 1. Command Line Interface Error Codes Error Code Short Description 0x01 0x02 0x03 0x04 0x05 Command Syntax Error. A command followed by /? displays a command usage. The parameter has a format error. A command with the certain [Parameter Name]
followed by /? displays the format and range of the variable. The parameter is out of allowed range. A command with the certain [Parameter Name] followed by /? displays the format and range of the variable. The command is not valid for specific radio model. To display the list of available commands, the HELP command must be used. Unspecified Error 1.1. Software Switching to Command Mode On power-up the radio modem is in data-mode. To switch to command mode the special byte-sequences with special meanings are used:
Escape-Sequence: +++ with 20 ms guard time before and after the command characters
Escape-Acknowledge: @00<CR><LF>
20 ms toggling on CTS control line needed to acknowledge switching from Data to Command mode and vice versa. 28 www.javad.com Command Line Interface Command Line Interface Convention Happy Flow 1. 2. In data-mode the unit starts looking for the Escape-sequence if there is no data from DTE (Data Terminal Equipment) for more than 20 ms (Start Guard Time). If the unit detects the Escape-Sequence:
The transmitter continues sending over the air the data received from DTE before Escape-
Sequence and buffers the data from DTE;
The Receiver immediately stops forwarding to DTE the data received over the air and buffers it instead. 3. The radio unit waits for 20 ms and then sends Escape-Acknowledge to DTE if there is no data from DTE during 20 ms of Stop Guard Time. 4. The unit goes to command mode and discards Escape-Sequence from input buffer. The modem is immediately ready to receive commands. At the same time it continues buffering the data received over the air since step 2. Escape-Sequence in Data During its waiting in step 3, the unit receives data from DTE:
The unit sends buffered Escape-Sequence from DTE to the air;
The unit sends all buffered data received from the air since step 2 to DTE and stays in data-mode
(i.e. transmits data received from DTE over the air including the just received, unexpected, data and forwards data received over the air to DTE.) 1.2. Hardware Switching to Command Mode As alternative to Software Switching, the switching through the MP/DP (Data Terminal Ready, DTR) control line can be used. To set Command Mode, the DTE must assert DTR signal active and then passive. By falling edge of DTR signal the unit goes to command mode and then sends Escape-
Acknowledge to DTE (@00<CR><LF>). 20 ms toggling on CTS control line needed to acknowledge switching from Data to Command mode and vice versa. Note: The powered up radio modem by default goes to Data Mode regardless of DTR control line polarity. 1.3. Switching to Data Mode
DTE sends the CLI command DATAMODE<CR><LF> to the unit.
Unit answers with Escape-Acknowledge (@00<CR><LF>) and immediately goes to datamode, so that the DTE can start sending data as soon as the Escape-Acknowledge has been received.
If no valid CLI commands received from DTE within 1 minute, the unit will automatically switch back to data-mode. www.javad.com 29 Command Line Interface Networking Commands 2. Networking Commands 2.1. LINK The LINK command is responsible for configuring radios operation mode. It has parameters listed below. Note: In parentheses is shown firmware version, which supports this parameter. If the firmware version is not specified, it means that this parameter is supported in both versions. LINK [Parameter Name] [Parameters List] [/?]
Parameter Name PROT MOD SPACE Parameter List 1 - Simplex Receiver, a default setting for Remote units (for firmware version 1.8) 2 - Simplex Transmitter (for firmware version 1.8) 3 - Half Duplex specific for remote units (for firmware 3.0 and newer) 4 - Half Duplex specific for base unit (for firmware 3.0 and newer) 5 - Reserved for future use 6 - Reserved for future use 7 - TRMB Receiver (used with GMSK modulation, Trimble compatible) (for firmware version 1.8) 8 - TRMB Transmitter (used with GMSK modulation, Trimble compatible) (for firmware version 1.8) 9 - Transparent w/EOT Repeater (used with GMSK and 4FSK, Pacific Crest compatible) (for firmware version 1.8) 10 - Repeater (JAVAD Proprietary Simplex) (for firmware version 1.8) 11 - TRMB Repeater (used with GMSK modulation, Trimble compatible) (for firmware version 1.8) 12 - Transparent w/EOT Receiver (used with GMSK and 4FSK modulation, Pacific Crest compatible) (for firmware version 1.8) 13 - Transparent w/EOT Transmitter (used with GMSK and 4FSK modulation, Pacific Crest compatible) (for firmware version 1.8) 14 - STL Receiver (used with 4FSK modulation, Satel compatible) (for firmware version 1.8) 15 - STL Transmitter (used with 4FSK modulation, Satel compatible) (for firmware version 1.8) 1 DBPSK 2 DQPSK, a default settings 3 D8PSK 4 D16QAM 5 GMSK 6 4FSK Sets channel spacing:
0 - 25kHz, a default setting 1 - 12.5kHz 2 - 6.25kHz 3 - 20kHz PWRB / PWRW (25 - 46) / (320 - 3500) - RF output Power in dBm / mW FHOP (only for firmware ver. 1.8) SCRAM
(0 - 32) - Frequency Hoping Pattern number LINK FHOP command can be processed only if the Channel Map (up to 32 channels) 0 - No Scrambling (a default setting)
(1 - 255) - Seed for Pseudo-Random Sequence Generator 0 - Disable Forward Error Correction (FEC), a default setting 1 - Enable Reed-Solomon encoding FEC 30 www.javad.com Command Line Interface Serial Interfacing Commands Parameter Name RTR
(only for firmware version 1.8) Parameter List Base Unit 0 - No Retransmission in the wireless cluster 1- There is Repeater Remote Unit 0 - Auto Detect (Base or Repeater) 1 - Receive from Repeater 2 - Receive from Base Note: The frequency defined by CHAN parameter is not valid if Frequency Hoping mode is selected. In the Frequency Hoping mode, the Frequency Pattern generator must generate the random numbers smaller than the number of frequencies listed in the unit's frequency list. 3. Serial Interfacing Commands 3.1. DPORT The DPORT is an object that responsible for data port interface configurations like Bit Rate, Flow Control, etc. DPORT [Parameter Name] [Parameters List] [/?]
Parameter Name RATE BITS PARITY FLOW RS DATATX Parameter List 0 Maintenance Port baud rate, a default setting 1 1200 baud 2 2400 baud 3 4800 baud 4 9600 baud 5 14400 baud 6 19200 baud 7 38400 baud 8 57600 baud 9 115200 baud, a default setting Set number of bits in one byte (8 or 7) 8 is a default setting 0 None, a default setting 1 Odd 2 Even 0 None, a default setting 1 Not used 2 HW (RTS/CTS) 0 - RS232, a default setting 1 - RS485 2 - RS422 use save, boot commands to activate modification 0 - UART, a default setting 1 - USB 2 - BT www.javad.com 31 Command Line Interface Serial Interfacing Commands Parameter Name DATARX Parameter List 0 - UART, a default setting 1 - USB 2 - BT The response of command without Parameter Name indicates all values:
RATE =0 BITS =8 PARITY =NONE FLOW =NONE DTR =0 RS =RS232 DATATX =UART DATARX =UART, BT 3.2. MPORT The MPORT is an object that responsible for maintenance serial port interface configurations such as data rate and number of bits in a byte. MPORT [Parameter Name] [Parameters List] [/?]
Parameter Name Parameter List RATE 0 Auto. 1 1200 baud 2 2400 baud 3 4800 baud 4 9600 baud 5 14400 baud 6 19200 baud 7 38400 baud 8 57600 baud 9 115200 baud, a default setting Note: JAVAD GNSS radio modems does not support data flow and parity on the maintenance serial port.The radio modem with none-dedicated maintenance serial port must keep CTS line always active in MPORT mode (DP/MP is low). 32 www.javad.com Command Line Interface Special Commands 4. Special Commands 4.1. BOOT The factory software image and default configuration is set for the new unit. The BOOT command is intended to reboot the unit using specified software image and selected configuration. BOOT IMAGE BOOT CFG The BOOT command with no parameters selects the user settings defined by the prior parameterized BOOT commands. 4.2. HELP The HELP command types the list of all available commands:
HELP- Display this usage BOOT- Reboot the unit LINK- Set RF Link Operation Mode DPORT- Set Data Port Configuration MPORT- Set Maintenance Port Configuration ALARM- Alarm Indication and Alarm Control Configuration SLEEP- Set Sleep Mode Configuration STATE- Display Status and Statistics SAVE- Save Current Configuration into Configuration File INFO- Display Product ID along with Hardware/Software Versions ATI- Display Product ID along with Hardware/Software Versions MAP- Operates with Channel Map DATAMODE- Exit Command Mode
[COMMAND] /?- Display Command Usage 4.3. SAVE The SAVE command is intended to store the units currently used configuration into the User Configuration file. The configuration stored in the User Configuration file is activated by automatically after units reboot. www.javad.com 33 Command Line Interface Diagnostics and Identification Commands 4.4. SLEEP The SLEEP command determines the sleep mode parameters. The sleeping AW225BT can be activated by real-time CLK, DTR/RTS lines, and command received through TTL inputs. The user can select one, two, or all three conditions. SLEEP [Parameter Name] [Parameters List] [/?]
Parameter Name Parameter List CLK HW TTL GTS 0 Do not activate by internal real-time clock
(1 255) Activate by internal real-time clock after 100 to 25500 msec of sleeping 0 Do not activate through DTR/RTS lines 1 Activate through DTR/RTS lines 0 Do not activate by external sense lines 1 Activate by external sense lines 0 Disable Sleep mode (default)
(1 255) Go to sleep mode if there is no activity in 10 to 2550 msec 5. Diagnostics and Identification Commands 5.1. INFO The INFO command is used to retrieve the Radio ID along with its Hardware version, the loaded real-
time software version/revision and BootLoaders version/revision. INFO [Parameter Name] [Parameters List] [/?]
Parameter Name Parameter List ID SN HW SW BL BT Product ID:
38 - HPT225BT 42 - AW225BT Six bytes Serial Number (SN) 1.0 - hardware version in numeric Major.Minor format Ver. 1.0 Rev. A - displays software's version in numeric Major.Minor format and revision in numeric format (range from 01 to 99) for engineering releases and alphabetic format (A to Z) for manufacturing releases Ver. 1.0 Rev. A - displays BootLoaders version in numeric Major.Minor format and revision in numeric format (range from 01 to 99) for engineering releases and alphabetic format (A to Z) for manufacturing releases Bluetooth serial number The INFO command without Parameter Name indicates all values:
HPT225BT High Power VHF Transceiver, Javad GNSS Product ID =38 S/N =0000000123BB Hardware =Ver. 3.3 34 www.javad.com Command Line Interface Diagnostics and Identification Commands Software =Ver. 1.8 Rev 04 B24 BootLoader =Ver. 3.0 Rev 03 BT addr =00:18:D7:00:3C:C7 5.2. STATE The STATE command is used to check the state of the wireless link, the unit in the link, and the alarm control lines. To specify a radio unit (local or remote), the CONNECT command must be used in prior of STATE command using. STATE [Parameter Name] [Parameters List] [/?]
Parameter Name RSSI BER FREQ TEMP SYNC MODE VHPA BT Parameter List
-15 to -137 dBm - Indicates the Receive Signal Strength in dBm 0 to 9.9E-3 - Indicates the BER level 215.000000 to 255.000000 MHz - Displays the central frequency of the operating channel
-30.C to 100.C. Displays the temperate inside of enclosure. 0 - if link is not established yet 1 - indicates the link established AUTO/FHOP/FIXED VCC V ON/OFF The STATE command without Parameter Name indicates all values as shown below:
RSSI =-141 dBm BER =0E-0 FREQ = 225.000000 MHz CHAN =-4 TEMP =32 SYNC =0 MODE =FIXED VHPA =11.75 V BT =ON www.javad.com 35 Command Line Interface Diagnostics and Identification Commands 36 www.javad.com Appendix A SPECIFICATIONS 1. HPT225BT VHF Modem Specifications The following sections provide specifications for the modem and its internal components. 1.1. General Radio Specifications Table 1. General Radio Specifications Parameter Operating Frequency Range1 Channel Spacing1 Data Rate (25/20/12.5/6.25 kHz Channel Spacing) System Gain for DBPSK modulation (Antenna gain is not included) Roaming Speed for DBPSK modulation 75 mph / 120 km/h Modulation Nominal Impedance End to End delay Communication Mode Specification 215-255 MHz (EU) 217-220 MHz and 220-222 MHz (USA) 217-218 MHz, 219-220 MHz and 220-222 MHz (Canada) 25/12.5/6.25 kHz (USA, Canada) 25/20/12.5 kHz (EU) 9600/7500/4800/2400 bps DBPSK/GMSK 19200/15000/9600/4800 bps DQPSK/4FSK 28800/22500/14400/7200 bps D8PSK 38400/30000/19200/9600 bps D16QAM 160 dB (for 25 kHz Channel Spacing) 162 dB (for 12.5 kHz Channel Spacing) 163 dB (for 6.25 kHz Channel Spacing) GMSK/4FSK/DBPSK/DQPSK/D8PSK/D16QAM 50 Ohms 60 ms Time Division Duplex (TDD) Time Division Multiple Access (TDMA) 40 miles / 65 km Serial (RS-232) up to 115200 bps. Serial port configurable as RS-232 and RS-422, or RS-485 USB 2.0 device port (12 Mbps) Bluetooth V2.0 Class 2 supporting SPP Slave and Master Profiles External Maximum Distance Range Serial port USB Bluetooth Bluetooth Antenna www.javad.com 37 Specifications HPT225BT VHF Modem Specifications 6.25 kHz channels will occur in increments of 6.25 kHz from 217.00625 MHz to 219.99375 1. MHz for USA. 6.25 kHz channels will occur in increments of 6.25 kHz from 217.00625 MHz to 217.99375 MHz;
from 219.00625 MHz to 219.99375 MHz for Canada. 12.5 kHz channels will occur in increments of 12.5 kHz from 217.0125 MHz to 219.9875 MHz for USA. 12.5 kHz channels will occur in increments of 12.5 kHz from 217.0125 MHz to 217.9875 MHz;
from 219.0125 MHz to 219.9875 MHz for Canada 25 kHz channels will occur in increments of 25 kHz from 217.025 MHz to 219.975 MHz for USA. 25 kHz channels will occur in increments of 25 kHz from 217.025 MHz to 217.975 MHz;
from 219.025 MHz to 219.975 MHz for Canada 6.25 kHz channels will occur in increments of 6.25 kHz from 220.00625 MHz to 221.99375 MHz for USA and Canada. 12.5 kHz channels will occur in increments of 12.5 kHz from 220.0125 MHz to 221.9875 MHz for USA and Canada. 25 kHz channels will occur in increments of 25 kHz from 220.025 MHz to 221.975 MHz for USA and Canada. 1.2. Environmental Specifications Table 2 lists the modems environmental specifications. Table 2. Environmental Specifications Parameter Specification Temperature Environmental Dimensions (H x W x D) Weight Power Supply Voltage Power Consumption (Average):
Continuous Transmit/
Transmit with 30% duty cycle / Sleep Housing/Color VHF Antenna Connector Bluetooth Antenna Connector Operating 40oC to +60oC Storage 40oC to +85oC IP 66 152 mm x 84 mm x72 mm 900 g
+9... +16VDC nominal 120W/38W/300mW (USA, Canada) 60/20/300mW (EU) Aluminum / Two-tone JAVAD GNSS Green / Gray BNC, 50 SMA, 50 38 www.javad.com Specifications HPT225BT VHF Modem Specifications 1.3. Transmitter Specifications Table 3 lists the transmitter specifications. Table 3. Transmitter Specifications Parameter Specification Output Power EU USA (217 - 220 MHz) USA (220-222MHz) Canada Output Power Control Accuracy Carrier Frequency Stability Max. Frequency Error Adjacent Channel Power (Conducted) 25/12.5/6.25 kHz CS USA, Canada 25/20/12.5 kHz CS EU Spurious Emission (Conducted) Spurious Emission (Radiated) 25 dBm to 40 dBm in 1 dB step (320 mW to 10W) 25 dBm to 33 dB m in 1 dB step (320 mW to 2W) 25 dBm to 44 dB m in 1 dB step (320 mW to 25W) 25 dBm to 44 dB m in 1 dB step (320 mW to 25W) 1.5 dB (at normal test conditions) 1.5 ppm initial stability over temp with 3.0 ppm aging/year 1.0 kHz (at normal test conditions) 1.5 kHz (under extreme test conditions) Part 90.210 (C, D, E) Clause 4.2.4 EN 300 113-2 (60 dBc)
-36 dBm (9 kHz 1GHz)
-30 dBm (1GHz 4 GHz)
-36 dBm (9 kHz to 1 GHz)
-30 dBm (1 GHz to 4 GHz) 1.4. Receiver Specifications Table 4 lists the receiver specifications. Table 4. Receiver Specifications Parameter Specification Noise Figure Receiver Sensitivity DBPSK
(BER 1x10-4, 25 kHz CS DQPSK D8PSK D16QAM GMSK Dynamic Range Max. Input Signal Level Co-channel Rejection Adjacent Channel Selectivity 3 dB
-116 dBm 25kHz / -117 dBm 12.5kHz
-115 dBm 25kHz / -116 dBm 12.5kHz
-110 dBm 25kHz / -111 dBm 12.5kHz
-106 dBm 25kHz / -107 dBm 12.5kHz
-113 dBm 25kHz / -114 dBm 12.5kHz
-115 to 15 dBm
-10 dBm
-8 dB for 25 kHz Channel Spacing
-12 dB for 12.5 kHz Channel Spacing
-16 dB for 6.25 kHz Channel Spacing 70 dB for 25 kHz Channel Spacing 60 dB for 12.5 kHz Channel Spacing 50 dB for 6.25 kHz Channel Spacing www.javad.com 39 Specifications Compliance 2. Compliance Parameter Specification FCC Industry Canada R&TTE Part 90 RSS-119 ETSI EN 300 113-2; ETSI EN 301 489-5;
EN 60950-1:2006 3. Connector Specifications Power Connector Table 5 gives specifications to power connector type 23-500153-01 CONN, HIGH CURRENT PL-700 RECEPT ALDEN 300906. White Marker 1 2 Table 5. Power Connector Specifications Number Signal Name Dir Details 1 2 Power_INP Power_GND P
12 volts DC input Ground, power return 40 www.javad.com Specifications Connector Specifications DB15 Connector This provides DB15 connectivity for the HPT225BT with a DB9 for connection to a PC/CE Device for configuration. DB15 (Fem) This connector provides DB15 connectivity for the HPT225BT with DTE. About using and configuration RS-485 please contact JAVAD GNSS support. Figure 1. DB15 Connector Table 6. DB15 Connector Specifications Number Signal Name Dir Details 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 DCD DSR RTS DATAIN O O I I I Reserved USB_PWR Ground Reserved I DSR_IN TX+/RTS_OUT O TX-/TX_OUT O Reserved USB_D+
USB_D-
GND Data Carrier Detect (RS-232) Data Terminal Ready (RS-232) Receive Data positive line (RS-422)/
Clear to Send (RS-232) Receive Data negative line (RS-422)/
Receive Data (RS-232) Do not use Power Input line (USB) Power Ground Do not use Data Set Ready (RS-232) Transmit Data positive line (RS-422) /
Request to Send (RS-232) Transmit Data negative line (RS-422) /
Transmit Data (RS-232) Do not use Positive line (USB) Negative line (USB) Signal to Ground www.javad.com 41 Specifications Connector Specifications External Antenna RF Connector The external antenna connector type is a BNC RF connector AEP Connectors p/n 6501-7051-003. External Bluetooth Antenna Connector The external antenna connector type is a SMA connector Linx Technologies, Inc.CONSMA015-R178 42 www.javad.com Appendix B SAFETY WARNINGS Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Clean only with a damp cloth.
Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall be placed on the apparatus. 1. General Warnings HPT225BT is a wireless device used in a mobile application, at least 100 cm from any body part of the user or nearby persons. Note: Minimum separation distance of 100 cm between the antenna and persons must be maintained. This product should never be used:
Without the user thoroughly understanding operators manual.
After disabling safety systems or altering the product.
With unauthorized accessories.
Contrary to applicable laws, rules, and regulations. DANGER: THE HPT225BT SHOULD NEVER BE USED IN DANGEROUS ENVIRONMENTS. www.javad.com 43 Safety Warnings General Warnings 44 www.javad.com Appendix C VHF RADIO USAGE Many countries require a license for radio users (such as the United States of America). Be sure you comply with all local laws while operating a VHF radio. Surveying in RTK mode has made VHF the most popular choice for communications between base and rover receivers. Know the strengths and weaknesses of this technology to get the best use out of your receiver. The quality and strength of the VHF signals translates into range for VHF communications. The systems range will greatly depend on the local conditions. Topography, local communications and even meteorological conditions play a major role in the possible range of RTK communications. If needed, use a scanner to find clear channels for communication. www.javad.com 45 VHF Radio Usage 46 www.javad.com Appendix D WARRANTY TERMS JAVAD GNSS electronic equipment are guaranteed against defective material and workmanship under normal use and application consistent with this Manual. The equipment is guaranteed for the period indicated, on the warranty card accompanying the product, starting from the date that the product is sold to the original purchaser by JAVAD GNSS Authorized Dealers1. During the warranty period, JAVAD GNSS will, at its option, repair or replace this product at no additional charge. Repair parts and replacement products will be furnished on an exchange basis and will be either reconditioned or new. This limited warranty does not include service to repair damage to the product resulting from an accident, disaster, misuses, abuse or modification of the product. Warranty service may be obtained from an authorized JAVAD GNSS warranty service dealer. If this product is delivered by mail, purchaser agrees to insure the product or assume the risk of loss or damage in transit, to prepay shipping charges to the warranty service location and to use the original shipping container or equivalent. A letter should accompany the package furnishing a description of the problem and/or defect. The purchaser's sole remedy shall be replacement as provided above. In no event shall JAVAD GNSS be liable for any damages or other claim including any claim for lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, the product. 1. The warranty against defects in JAVAD GNSS battery, charger, or cable is 90 days. www.javad.com 47 900 Rock Avenue, San Jose, CA 95131 USA Phone: +1(408)770-1770 Fax: +1(408)770-1799 www.javad.com Copyright JAVAD GNSS, Inc., 2012 All rights reserved. No unauthorized duplication.
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2012-12-17 | 220 ~ 222 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2012-12-17
|
||||
| 1 | Applicant's complete, legal business name |
JAVAD GNSS, Inc.
|
||||
| 1 | FCC Registration Number (FRN) |
0017985318
|
||||
| 1 | Physical Address |
900 Rock Avenue
|
||||
| 1 |
San Jose, California 95131
|
|||||
| 1 |
United States
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
t******@intertek.com
|
||||
| 1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
WJ4
|
||||
| 1 | Equipment Product Code |
HPT225
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
V**** V****** Z******
|
||||
| 1 | Title |
Dr.
|
||||
| 1 | Telephone Number |
40877********
|
||||
| 1 | Fax Number |
40877********
|
||||
| 1 |
v******@javad.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF RADIO TRANSCEIVER | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Power output listed is conducted. This device must be restricted to work related operations in an Occupational/Controlled RF exposure environment and must operate with a duty factor not exceeding 50%. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 100cm from all persons. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Intertek Testing Services NA Inc.
|
||||
| 1 | Name |
J******** Q******
|
||||
| 1 | Telephone Number |
949-4********
|
||||
| 1 | Fax Number |
650-4********
|
||||
| 1 |
j******@intertek.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 3K04G1D | |||||||||||||||||||||||||||||||||
| 1 | 2 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 3K05G1D | |||||||||||||||||||||||||||||||||
| 1 | 3 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 3K00F1D | |||||||||||||||||||||||||||||||||
| 1 | 4 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 2K92F1D | |||||||||||||||||||||||||||||||||
| 1 | 5 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 6K02G1D | |||||||||||||||||||||||||||||||||
| 1 | 6 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 6K03G1D | |||||||||||||||||||||||||||||||||
| 1 | 7 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 5K96F1D | |||||||||||||||||||||||||||||||||
| 1 | 8 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 5K88F1D | |||||||||||||||||||||||||||||||||
| 1 | 9 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 12K0G1D | |||||||||||||||||||||||||||||||||
| 1 | 1 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 11K9G1D | |||||||||||||||||||||||||||||||||
| 1 | 11 | 9 | EF | 217 | 220 | 2 | 0.7 ppm | 11K7F1D | |||||||||||||||||||||||||||||||||
| 1 | 12 | 9 | EF | 220 | 222 | 25 | 0.7 ppm | 11K6F1D | |||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC