all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 4.78 MiB | February 05 2013 | |||
1 | Cover Letter(s) | February 05 2013 | ||||||
1 | Cover Letter(s) | February 05 2013 | ||||||
1 | External Photos | February 05 2013 | ||||||
1 | ID Label/Location Info | February 05 2013 | ||||||
1 | Internal Photos | February 05 2013 | ||||||
1 | Test Report | February 05 2013 | ||||||
1 | Test Setup Photos | February 05 2013 |
1 | User Manual | Users Manual | 4.78 MiB | February 05 2013 |
Tally Dascom DM-210/220 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operators Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances. Ensure the printer is connected to a socket with the correct mains voltage. Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Make sure that both of the printer and the computer are switched off before connecting the data cable. The print head will become very hot during printing; avoid contact with the print head after printing has finished. Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. I Tally Dascom DM-210/220 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Stoffen auf. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Keine Flssigkeiten mit dem Drucker in Berhrung bringen. Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit abkhlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. II Tally Dascom DM-210/220 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service. Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un dpanneur qualifi. Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber. Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de substances explosives. Ne connecter limprimante une prise que lorsque la tension est correcte. Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension et toujours dbrancher le connecteur secteur de la prise murale. Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la poussire. Ne pas mettre limprimante en contact avec des liquides. Ne pas exposer limprimante des chocs, impacts ou vibrations. Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de donnes. La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir quelques instants avant dy toucher. N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. III Tally Dascom DM-210/220 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere. Evitare il contatto della stampante con liquidi. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. IV Tally Dascom DM-210/220 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un tcnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sunstancias explosivas. Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentacin del enchufe. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegrese de que la impresora y el ordenador estn apagdos antes de conectar el cable de datos. La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarlo algn tiempo antes de tocarla. No permita que se realice cualquier operacin o accin de una forma diferente a lo que se seala en el manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. V Tally Dascom DM-210/220
. (Russian)
, . VI Tally Dascom DM-210/220 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora. Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou substncias explosivas. Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. No exponha a impressora a temperaturas altas ou luz solar direta. No aproxime substncias lquidas da impressora. Proteja a impressora de choques, impactos e vibraes. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de toc-la. No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, contate seu revendedor ou companhia de servio. VII Tally Dascom DM-210/220 nemli Gvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatle okuyun. Bakm ve tamir almalarn kesinlikle ve hibir surette kendi banza yapmayn; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazcy, zerinden yere dmesi mmkn olmayacak sabit ve dz bir zemine yerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veya patlayc maddeler ieren nesnelerin yaknna koymayn. Yazc akm kablosunu sadece doru gerilime sahip bir prize takn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zaman prizden kartn. Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalan meknlarda bulundurun. Yazc hibir sv maddeyle temasta olmamaldr. Yazc hibir sarsntya, darbeye veya titreime mruz kalmamaldr. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapal olduklarndan emin olmalsnz. Yazcnn ba basma esnasnda yksek sya ulayor. Bu yzden ltfen dokunmadan nce ksa sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfen imlatnza veya mteri hizmetleri servisinize bavurun. VIII Tally Dascom DM-210/220 TRADEMARK ACKNOWLEDGEMENTS IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7,Windows 8, Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008/2013 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom DM-210/220 X Tally Dascom DM-210/220 TABLE OF CONTENTS 1 PRINTER INSTALLATION GUIDE................................................................................................... 1 1.1 Unpacking the Printer ................................................................................................................1 1.2 Placing the Printer .....................................................................................................................2 1.3 Printer Components...................................................................................................................3 1.4 Connecting the Interfaces ..........................................................................................................4 1.5 Connecting the Power................................................................................................................5 1.6 Loading Paper ............................................................................................................................6 1.7 Installing Ribbon Cartridge.........................................................................................................7 1.8 Installing the Printer Driver........................................................................................................8 2 CONTROL PANEL OPERATION ..................................................................................................... 10 3 TROUBLESHOOTING ................................................................................................................... 12 3.1 Processing Indicator Error ........................................................................................................ 12 3.2 Processing Printing Error.......................................................................................................... 12 3.3 Removing Jammed Paper......................................................................................................... 12 4 SPECIFICATIONS.......................................................................................................................... 13 4.1 Data Sheet ............................................................................................................................... 13 4.2 Interfaces................................................................................................................................. 15 4.2.1 USB interface..................................................................................................................... 15 4.2.2 Cashbox interface .............................................................................................................. 15 4.2.3 Serial interface .................................................................................................................. 16 4.2.4 Parallel interface................................................................................................................ 16 4.3 Power Supply........................................................................................................................... 18 5 CHARACTER CODE PAGES ........................................................................................................... 19 6 PRINTING CONTROL COMMAND SETS........................................................................................ 26 FCC STATEMENT............................................................................................................................. 27 DASCOM REPRESENTATIVES .......................................................................................................... 28 Tally Dascom DM-210/220 1 Printer Installation Guide 1.1 Unpacking the Printer Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. Check the printer for any visible transport damage and missing items. If you find any transport damage or any accessories are missing, please contact your dealer for assistance. Please keep the packaging material for future transportation. The shipping list varies with different customized order requirements. 1 Tally Dascom DM-210/220 1.2 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions:
Never place the printer near to any flammable gas or explosive substances. Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. Ensure sufficient distance between the printer and any heating devices or radiators. Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. 2 Tally Dascom DM-210/220 1.3 Printer Components
(DM210 only) Components Function Cover Open Key Open the Printer Cover (DM-210 only). Top Cover Open the cover when loading or reloading roll paper. Open the cover when ribbon cartridge Power Switch Powers printer ON or OFF. Power Indicator Shows printer power on or not. Paper End Indicator Shows roll paper out or not. Feed Key Press the key to feed paper. Error Indicator Shows error occurs or not. Control Panel Shows printer status. Power supply Socket Connects power cord to the printer. Cashbox Interface Connects Cashbox interface cable from the cashbox. USB Interface Connects USB interface cable from the host. Modular Interface Board Connects serial interface or parallel interface from the host. 3 Tally Dascom DM-210/220 1.4 Connecting the Interfaces The USB, Cashbox, Serial/Parallel interface are located at the rear of the printer. Choose the interface which suits your system. Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interfaces. Connecting cashbox interface Connecting USB interface Connecting parallel interface (modular, option) Connecting serial interface (Modular, option) 4 Tally Dascom DM-210/220 1.5 Connecting the Power Checking the printer voltage Make sure that the device has been set according to your countrys power supply voltage. To do this, check the rating plate at the rear of the printer. Contact your dealer if the setting is incorrect. 1. Make sure the printer and the computer are powered off . 2. Connect the power cord to the power adapter , and connect the power adapter to the power supply socket at the rear of the printer . Ensure the power cord is securely connected. Finally, connect the power cord plug to a mains socket on the wall . Power on and power off 1. Press the power switch to the I position to turn on the printer. Upon power-on, the Power LED indicator light up. 2. Press the power switch to the O position to turn off the printer. 5 Tally Dascom DM-210/220 1.6 Loading Paper 1. Keep power on and open the top cover. 2. Insert the end of paper into the entry of paper path, then sent it in with even force until the feeder motor drives to feed in the paper automatically. 3. Close the top cover The end of paper should be cut regularly and inserted into the entry of paper path, then sent it in with even force until the feeder motor drives to feed in the paper automatically. If paper jams results, pull out the paper when the automatic feeder motor stops. Cut off the fold side of the paper and reload it. If black mark is valid, the paper will be fed to the printing initial position. 6 Tally Dascom DM-210/220 1.7 Installing Ribbon Cartridge 1. Open top covers to show up the printhead. 2. Turn the ribbon knob on the right side in the direction indicated by the arrow on the cartridge to remove any slack. 3. Insert the ribbon between the print head and the platen, and press it in until it clicks into place. 4. Turn the knob again to remove any slack. 5. Close the cover. 7 Tally Dascom DM-210/220 1.8 Installing the Printer Driver Installing the Windows Driver (Compatible with Windows) Switch off the printer before running the printer driver setup. Your printer CD-ROM comes with Windows drivers. Go to the Drivers folder and run the installer DriverSetup.exe. 1. Double click the DriverSetup. You will see the screen as below. Click Next to continue. Installation guide for USB, serial and parallel driver program 2. You might see the screen as below. Select the desired printer driver, and then click Next to continue. 8 Tally Dascom DM-210/220 3. Choose the desired port to use, and then click Next to continue. 4. Click Finish to finish the installation process successfully. 5. You will see the screen as below. Click OK to install the printer driver successfully. 9 Tally Dascom DM-210/220 2 Control Panel Operation There are power indicator, paper end indicator, error indicator and feed key in the printer. When pressing the Feed key, if the black mark detection is off, paper will be fed until Feed key is released; otherwise, the paper will be fed to the next black mark and stop. Indicator Illustration That the green indicator is on indicates that the power is on. Here are the illustrations for error indicators:
Indications Disposal Error indicator Paper end indicator Blink Blink On Off Memory Error The print head is over-heated Blink Blink The position of the carriage is wrong Check the SRAM chip, data bus, address line and selected signal,etc. Recover automatically until the temperature drops down. Check the stepper motor of the carriage, transmission mechanism, initial position sensor and drive circuit, etc. On Blink Paper end Load paper. Self-test Printing and Hexadecimal Dumping Turn off the printer after the ribbon cartridge and roller paper are installed, hold the feed key while power on, and then the printer will print out the self-test page. After the self-test completed, if there feed key is pressed, the printer will enter bidirectional printing adjustment state. If receiving data without pressing feed key, the printer will enter hexadecimal printing state. If you do not need to implement the alignment or hexadecimal printing, please switch off the printer and restart the printer for printer normal operation. 10 Tally Dascom DM-210/220 Bidirectional Printing Adjustment When typefaces are blurred or vertically misaligned, it is necessary to do the bidirectional printing quality adjustment. After self-test completed, the alignment parameter for bidirectional printing will change circularly along with pressing feed key and the printer will print out the reference typeface. When the printing quality becomes best, in other words, both the upper and lower rows of H are best aligned, you can turn off the power and the printer will save the parameters automatically. 11 Tally Dascom DM-210/220 3 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you can not resolve, please contact your dealer for assistance. Read the following instructions before maintenance and avoid operating beyond your capacity, so as to prevent injury to you and damage to the printer. 3.1 Processing Indicator Error Phenomenon Potential Problem Solution No indicators on Incorrect power supply cable connections and power outlet Check the power supply cable connections and the power outlet and correct them The printer does not switch on. Switch on the printer PCB damaged Contact your dealer for assistance Error Indicator always on and Paper End Indicator flashes Paper end Reload the roll paper Error Indicator flashes Print Head overheated Reprint until it cools 3.2 Processing Printing Error Phenomenon Potential Problem Solution Blurred printing or spot Paper can not be fed. Incorrect roll paper installation Check if the roll paper is installed correctly Unqualified roll paper Use recommended roll paper Paper stucked Open the printer cover, check the paper path and remove jammed paper The printer does not switch on. Switch on the printer Horizon print words missing Printhead pin damaged Contact your dealer for assistance 3.3 Removing Jammed Paper Printhead may be hot, please move the printhead by moving the carriage. Turn the printer off and open the top cover. Open the printer cover and remove the jammed paper. 12 Tally Dascom DM-210/220 4 Specifications 4.1 Data Sheet Print Parameter Print method Print direction Resolution Print speed Paper speed Print width feed Interface Power Sleep Cartridge Ribbon Copies Paper Feed Memory Fonts RAM Chinese Alphanumeric Code page Detect Function Black Mark Detection 9 pin dot matrix (Pin 0.30mm) bidirectional logic-seeking max 160dpiH x 144dpiV 4.3lps(4.3 line / sec at 42 columns) max 5.51ips (14cm/s) 42cpl @ 16.7cpi (7x8 matrix) Cashbox: DC 24V, 1A, 6 line RJ-11 connector USB 2.0: Full Speed, standard type B Connector Serial RS232C: 25-pin Sub-D (f) connector; supports DTR or XON/XOFF handshaking protocol; baud rate 4800~38400BPS; data Format 1 initial bit + 8 data bit + 1 or 2 stop bits, no Parity. Parallel CENTRONICS: 25-pin Sub-D (m) connector, 8-bit parallel;
supports BUSY/ACK handshaking protocol. Yes NH37701 (Purple), Lifetime: 3000,000 characters (Compatible to ERC-39) NH37703 (Black), Lifetime: 1000,000 characters 1+1 (Thickness: 0.05~0.08mm/page; Total thickness: 0.16mm) Friction feed Max. 32Kbytes data buffer GB18030_2000 16x16 7x8 and 9x8 ASCII font PC437/PC850/PC860/PC863/PC865/PC858 In the direction of paper feed:
Mark height 5mm; Mark width min 12mm;
Mark reflectivity < 10%; Non-mark reflectivity > 75%;
Mark to initial print position: 27mm; Mark to tear position 47mm;
Factory default: Mark detection on the right for receipt face; Can be changed to left using mark control commands. Feed key Key and LED Indicator Power Supply Paper Handle Key Power indicator Green LED Paper indicator Error indicator Input Output Paper type Paper width Paper thickness Paper roll diameter Paper load Red LED Red LED External power adapter AC 100V-240V 50-60Hz DC 24V5%, 2.1A, A-1009-3P interface Good quality normal white roll paper or carbonized roll paper 76.20.5mm (3 inch) 0.060.085mm for single paper Max. OD 83mm ID 10+2/-0mm Upward cover open and Easy paper loading DM-210: Manual tear;
DM-220: Auto-cutter; support full cut and partial cut. Full cut (Cuts the paper completely) Paper cut 13 Tally Dascom DM-210/220 Emulation Noise Operating condition Storage condition Dimensions Color Weight Printhead lifetime MTBF Cutter lifetime
(DM-220 Only) MCBF Driver program Utilities Physical Spec. Reliability Software Function Certification Partial cut (one point left uncut) Note: The point length is 2% of the paper width. ESC/POS Compatible command set The noise level is less than 50 dBA (to be measured following ISO 7779 and ISO 9296). 0~40/4090%RH
-40~55/93%RH 156260130 (LWH mm) Black Approx. 1.85kg (excluding roll paper) 150,000,000 characters 100,000 hours 500,000 cuts Conditions: Paper thickness < 0.16mm Max frequency: 20 cuts/min 10,000,000 lines 32bit: Windows (Win 7/Vista/XP/2000) 64bit: Windows (Win 7/Vista/XP/2000) Compatible to the EPSON POS Application (ESC/POS OS) Setup tool (The printer parameter can be uploaded and downloaded, and the firmware version updating is supported.) CCC, CE-Mark(CB, EMV, EMC), UL, FCC, REACH, WEEE/RoHS, GCPO, Labeling/Packaging and Energy Star 14 4.2 Interfaces Power Supply interface, USB interface and cashbox interface are standard interfaces for the printer. Serial interface and Parallel interface are optional interfaces for the printer. The interface pin assignment is listed below. 4.2.1 USB interface USB interface pin assignment PIN No. Description 1 2 3 4 VBUS D-
D+
GND USB interface connector diagram 4.2.2 Cashbox interface Cashbox interface pin assignment Classic wire color Red White Green Black Pin No. 1 2 3 4 5 6 Description Structure GND Cashbox drive signal NC DC +24V Cashbox drive signal Signal GND Cashbox interface connector diagram Direction
Output Empty Output Output
4.2.3 Serial interface The serial interface of this printer is compatible with RS-232C, use DB25 hole type socket, support hardware handshaking protocol, the default baud rate and data format are 9600BPS, 8 data bit, no parity, and 1 stop bit. Below is the pin No of the serial interface socket. Pin signal definition of serial interface Pin No 2 3 20 Signal Name Direction Illumination TXD RXD From printer to PC From PC to printer DTR From printer to PC Send data from printer to PC Printer receive data from PC When the signal is negative, it means that the printer is busy and can not receive data; While the signal is positive, it means that the printer is ready and can receive the data. 1,7 GND GND The default baud rate is 9600 BPS and the baud rate can be changed by sending 16 Hex. command 1C AA 22 XX. XX: 00 indicates 1200 BPS, 01 indicates 2400 BPS, 02 indicates 4800 BPS, 03 indicates 9600 BPS, 04 indicates 19200 BPS, 05 indicates 38400 BPS. 4.2.4 Parallel interface The parallel interface of this printer is compatible with CENTRONICS, support BUSY /ACK handshaking protocol, use DB25 pin type interface. Pin No. of DB25 pin interface as below Parallel Interface Pin No.25 Below is the pin signal definition of parallel interface socket:
Pin No 1 2 Signal Name Direction Illumination
/STB Input Select trigger, input data when the signal is at falling edge. indicate the parallel data DATA1 Input These signals 3 4 5 6 7 8 9 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 Input Input Input Input Input Input Input 10
/ACK Output 11 12 13 15 14 16 17 18 25 BUSY Output PE SEL Output Output
/ERR Output
/AUTOFD
/INIT
/SELIN GND Input Input Input
information from the first to eighth bits. For each signal, when the logic is 1 indicates high level, when the logic is 0 indicates low level. For responsion pulse, low level indicates that the printer has accepted the data and be ready for accepting next data. High level indicates that the printer is busy and can not accept data now. Low level indicates idle. Drop down to Low level with resistance, High level indicates paper end. Full up to High level with resistance and the High level indicates the printer is online. Full up to High level with resistance and the High level indicates no error. Auto paper feed Initialize the printer online GNDlogic 0 level
(1) Input indicates inputting signals to printer; Output indicates outputting signals from printer.
(2) The average logic level of signal is TTL level.Signal Timing Diagram for parallel interface as shown below 4.3 Power Supply The external power supply of this printer is 24VDC2.1A. The type of power socket is A-1009-3P. Power supply socket pin assignment Pin Number Signal Name 1 2 3 4
+24 V GND N.C F.G. Power supply connector diagram 5 Character Code Pages 5.1 Common to all pages (International Character Set: USA) 5.2 [PC437: USA, Standard Europe]
5.3 [PC850: Multilingual]
5.4 [PC860: Portuguese]
5.5 [PC863: Canadian-French]
5.6 [PC865: Nordic]
5.7 [PC858: Euro]
6 Printing Control Command Sets Be compatible with ESC/POS command set. List of Commands ASCII Code HT LF CR ESC SP n ESC n ESC % n ESC &
ESC *
ESC 2 ESC 3 n ESC <
ESC n ESC ESC D n NULL ESC J n ESC K n ESC R n ESC U n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC e n Hex 09 0A 0D 1B 20 n 1B 21 n 1B 25 n 1B 26 1B 2A 1B 32 1B 33 n 1B 3C 1B 3F n 1B 40 1B 44 n 0 1B 4A n 1B 4B n Function Illumination Moves the print head to the next horizontal tab position Causes the data in the line buffer to be printed and advances the paper one line. Causes the line of data to be printed and returns the current print position to the left margin. Set the space between characters to n/160 inch Set character printing mode Allow/Prohibit user-defined character Set user-defined character Set graphic dot matrix Select the line space to 1/6 inch Select the line space to 1/144 inch bring the print head back to the left margin Cancel user-defined character Initialize the printer Set/Clear all horizontal tab position Causes the line of data to be printed and advances the paper n/144 inch Causes the line of data to be printed and advances the paper n/144 inch reversely Select an International Character Set Set/Cancel unidirectional printing 1B 52 n 1B 55 n 1B 63 33 n Select paper end sensor 1B 63 34 n Set to stop printing when paper end 1B 63 35 n Allow/Prohibit feeder key 1B 64 n Causes the line of data to be printed and advances the paper n line. Causes the line of data to be printed and advances n line reversely Produce cashbox drive pulse Select Character Set Set Chinese printing mode 1B 65 n 1B 70 1B 74 n 1C 21 n 1C 3F c1 c2 Cancel User-defined Chinese 1C 53 n1 n2 Set Chinese character space 1C 57 n 1D 0C 1B 43 n ESC p ESC t n FS n FS ? c1 c2 FS S n1 n2 FS W n GS FF ESC C n GS ( F pL pH a m nL nH 1D 28 FS ( L GS V m ESC i ESC m 1C 28 4C 1D 56 m 1D 56 m n 1B 69 1B 6D Set/Cancel Four double angle Chinese mode Send the black mark paper to the printing initial position Set the page length to n line space Set the orientation offset of black mark Feed the paper to the cut/tear position Select the cut/tear mode and cut/tear paper Cut the paper completely Cut the paper partially FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
aThis device may not cause harmful interference. bThis device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orientate or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980 USA Phone:+1 (877) 434 13 77 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent
#29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House, Priestley Road Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com CHINA JIANGMEN DASCOM COMPUTER PERIPHERALS CO., LTD No. 399, Jinxing Road, Jianghai District, Jiangmen, Guangdong P.R. China www.dascom.com All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. 2013 DASCOM Part No: 21.511.902.0040R
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-05-02 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2013-05-02
|
||||
1 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021247903
|
||||
1 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 |
Jiangmen City Guang Dong Province, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
k******@emcc.de
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Z7O
|
||||
1 | Equipment Product Code |
DM2100
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y**** H********
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
0750-********
|
||||
1 | Fax Number |
0750-********
|
||||
1 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Dot Matrix Printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Dongguan Dongdian Testing Service Co.,Ltd
|
||||
1 | Name |
J**** Y******
|
||||
1 | Telephone Number |
086-0******** Extension:
|
||||
1 |
y******@163.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC