all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual | Users Manual | 4.67 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Cover Letter(s) | February 11 2011 | ||||||
1 2 | Cover Letter(s) | February 11 2011 | ||||||
1 2 | ID Label/Location Info | February 11 2011 |
1 2 | User Manual | Users Manual | 4.67 MiB |
User Guide 1125 Matrix Printer Tally Dascom 1125 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operators Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances. Ensure the printer is connected to a socket with the correct mains voltage. Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Make sure that the printer and computer are switched off before connecting the data cable. The print head will become very hot during printing; avoid contact with the print head after printing has finished. Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. I Tally Dascom 1125 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.
Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf.
Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Stoffen auf.
Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen.
Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen.
Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.
Keine Flssigkeiten mit dem Drucker in Berhrung bringen.
Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen.
Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird.
Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit abkhlen lassen.
Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. II Tally Dascom 1125 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service.
Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un dpanneur qualifi.
Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber.
Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de substances explosives.
Ne connecter limprimante une prise que lorsque la tension est correcte.
Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension et toujours dbrancher le connecteur secteur de la prise murale.
Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la poussire.
Ne pas mettre limprimante en contact avec des liquides.
Ne pas exposer limprimante des chocs, impacts ou vibrations.
Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de donnes. La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir quelques instants avant dy toucher.
N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. III Tally Dascom 1125 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato.
Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive.
Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa.
Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere.
Evitare il contatto della stampante con liquidi.
Non esporre la stampante a colpi, scosse o vibrazioni.
Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati.
Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante.
Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. IV Tally Dascom 1125 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un tcnico de servicio calificado.
Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier momento.
Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sunstancias explosivas.
Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentacin del enchufe.
No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.
No ponga la impresora en contacto con fluidos.
Nunca exponga la impresora a sacudidas, choques o vibraciones.
Asegrese de que la impresora y el ordenador estn apagdos antes de conectar el cable de datos. La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarlo algn tiempo antes de tocarla.
No permita que se realice cualquier operacin o accin de una forma diferente a lo que se seala en el manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. V Tally Dascom 1125
. (Russian)
, , .
,
.
.
, .
.
.
,
.
, .
.
, .
, ,
.
. -
, .
, . ,
. VI Tally Dascom 1125 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora.
Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou substncias explosivas. Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.
No exponha a impressora a temperaturas altas ou luz solar direta.
No aproxime substncias lquidas da impressora.
Proteja a impressora de choques, impactos e vibraes.
Desligue a impressora e o computador antes de conectar o cabo da rede.
A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de toc-la.
No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, contate seu revendedor ou companhia de servio. VII Tally Dascom 1125 nemli Gvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatle okuyun.
Bakm ve tamir almalarn kesinlikle ve hibir surette kendi banza yapmayn; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazcy, zerinden yere dmesi mmkn olmayacak sabit ve dz bir zemine yerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veya patlayc maddeler ieren nesnelerin yaknna koymayn. Yazc akm kablosunu sadece doru gerilime sahip bir prize takn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zaman prizden kartn. Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalan meknlarda bulundurun. Yazc hibir sv maddeyle temasta olmamaldr. Yazc hibir sarsntya, darbeye veya titreime mruz kalmamaldr. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapal olduklarndan emin olmalsnz. Yazcnn ba basma esnasnda yksek sya ulayor. Bu yzden ltfen dokunmadan nce ksa sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfen imlatnza veya mteri hizmetleri servisinize bavurun. VIII Tally Dascom 1125 TRADEMARK ACKNOWLEDGEMENTS IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7, Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom 1125 X Tally Dascom 1125 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PLACING THE PRINTER .......................................................................................................................................... 2 PRINTER COMPONENTS ........................................................................................................................................ 2 2 SETTING UP PRINTER .................................................................................................................................... 4 INSTALL RIBBON .................................................................................................................................................. 4 INSTALL THE SINGLE SHEET FEEDER....................................................................................................................... 5 CONNECTING THE INTERFACE CABLE ...................................................................................................................... 5 CONNECTING THE MAINS POWER .......................................................................................................................... 6 INSTALLING THE WINDOWS DRIVER ........................................................................................................................ 7 3 PAPER INSTALLATION GUIDE ..................................................................................................................... 10 ADJUSTING THE PRINT GAP LEVER ....................................................................................................................... 10 FRICTION FEED HANDLING.................................................................................................................................. 11 TRACTOR FEED HANDLING .................................................................................................................................. 12 CONTINUOUS PAPER PLACEMENT ........................................................................................................................ 12 4 CONTROL PANEL OPERATION .................................................................................................................... 14 PANEL OPERATION ............................................................................................................................................. 16 Online State ............................................................................................................................................................ 17 Setup State ............................................................................................................................................................. 18 Power-On State ...................................................................................................................................................... 19 LANGUAGE SETUP .............................................................................................................................................. 20 5 PRINTER SETTING CHANGES ..................................................................................................................... 21 SYSTEM SETUP .................................................................................................................................................. 21 PRINT SETUP ..................................................................................................................................................... 21 PAGE SETUP ...................................................................................................................................................... 23 INTERFACE SETUP .............................................................................................................................................. 24 ADVANCED SETUP.............................................................................................................................................. 24 VERTICAL ALIGNMENT ........................................................................................................................................ 34 CHANGE PIN FUNCTION...................................................................................................................................... 35 ADJUST PHYSICAL MARGINS ............................................................................................................................... 36 DASCOM PRINTER SETUP TOOL ........................................................................................................................... 38 6 MAINTENANCE ............................................................................................................................................. 39 CLEANING AND VACUUMING THE PRINTER ............................................................................................................. 39 CLEANING THE PAPER ROLLERS ........................................................................................................................... 39 7 TROUBLESHOOTING .................................................................................................................................... 41 PRINT QUALITY PROBLEMS AND SOLUTIONS ........................................................................................................ 41 PAPER HANDLING PROBLEMS AND SOLUTIONS ..................................................................................................... 42 OPERATING PROBLEMS AND SOLUTIONS .............................................................................................................. 42 XI Tally Dascom 1125 ERROR INDICATIONS ON LEDS ............................................................................................................................ 43 DIAGNOSTIC FUNCTIONS .................................................................................................................................... 44 FIRMWARE UPDATE ........................................................................................................................................... 45 8 GENERAL SPECIFICATIONS ......................................................................................................................... 46 9 INTERFACES .................................................................................................................................................. 51 PARALLEL INTERFACE ......................................................................................................................................... 51 USB INTERFACE ................................................................................................................................................ 52 SERIAL INTERFACE ............................................................................................................................................. 52 10 CHARACTER SETS & CODE PAGES .......................................................................................................... 53 CHARACTER SETS .............................................................................................................................................. 53 INTERNATIONAL CHARACTER SETS ........................................................................................................................ 55 INTERNATIONAL CHARACTER SET COMMANDS ...................................................................................................... 55 CHARACTER TABLES ........................................................................................................................................... 56 CODE PAGE COMMANDS .................................................................................................................................... 58 CODE PAGE TABLES ........................................................................................................................................... 60 11 CONTROL CODES SUMMARY ................................................................................................................... 84 EPSON EMULATION COMMAND LIST.................................................................................................................... 84 IBM EMULATION COMMAND LIST ....................................................................................................................... 86 FCC STATEMENT ............................................................................................................................................. 88 XII Tally Dascom 1125 1 Unpacking Guide Place your packaged printer on a solid base.
Make sure that the Up symbols point in the correct direction.
Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging
material. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer. The following items should be included:
o Printer o Paper feed knob o Paper feed tray o Power cord o Ribbon cartridge o CD-ROM o Installation Guide Remove the packaging materials from the printer as follows:
1. Remove the tape on the paper feed lever. 2. Remove other visible tape on the printer. 3. Open and remove the top cover of the printer. 4. Remove the shipping cardboard from around the print head. 5. Install the paper feed knob. 1 Tally Dascom 1125 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions:
Never place the printer near to any flammable gas or explosive substances.
Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain.
When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. Ensure sufficient distance between the printer and any heating devices/radiators. Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing.
Printer Components 2 Tally Dascom 1125 Component Function Gap Lever Paper Guides Print Head Top Cover Control Panel Paper Feed Lever Paper Feed Knob Power Switch Ribbon Cartridge Ribbon Frame Tractors Power Receptacle Interface Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Adjusts positioning of single sheet paper. 24-pin printing mechanism Protects print head and other components inside, and reduce noise. Shows printer status, for printer setup. Two positions: = continuous forms; = single sheet paper Manual feed or vertical positioning of paper Power printer ON or OFF Install ribbon in the printer. For guiding ribbon installation on print head. For feeding and adjustment of continuous forms. Connects power cord to the printer. Connects interface cables from the host. 3 Tally Dascom 1125 2 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever A is set to the furthest open position. Move the carriage to the centre of the print platen. Install the recess positions on the ribbon cassette into the printer mounting. 2. 3. Press the ribbon frame onto the print head. 4. Turn the ribbon knob in clockwise direction until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly. 5. Ensure the print gap lever A is set to the original position. 6. Close the printers top cover. When printer is in operation, ensure the printers top cover is closed to keep the noise level to a minimum. Notes on Ribbon Cartridge Removal:
1. Eject any paper loaded in the printer. 2. Turn off the printer power. 3. Open and remove the top cover. 4. Lift up the tear bar. 5. Set the gap lever to the most open position labeled RIBBON. 6. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 7. Remove the blue ribbon frame from the print head. 8. Use fingers to take hold of the handle on the ribbon cartridge firmly, and lift the cartridge upwards to unlatch it. Some force may be needed to unlatch the cartridge. 4 Tally Dascom 1125 Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. Connecting the Interface Cable The 36-pin Centronics parallel, 25-pin serial RS-232C and USB ports are located at the rear of the printer. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports. 5 Tally Dascom 1125 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your countrys power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch A, located to the right side of the printer, is in the O (off) position. Connect the power cord to the power inlet of the printer. Connect the power cord plug to a mains socket. Switch on the printer. 6 Tally Dascom 1125 Installing the Windows Driver
(Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder Installer DriverSetup.exe. You will see the screen on the right. Click Next to continue. and the run 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to continue. to use. Click Next 3. Select the desired printer model as shown on the right. Click Next to continue. 7 Tally Dascom 1125 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click Next to continue. 5. Click Finish to start the installation process. 6.
(As we continue If the driver is not yet Microsoft Certified, the message on the right would appear. Click Continue Anyway. to expand our product portfolio, not all of our drivers may be certified yet. Please check our website www.dascom.com for the latest certified drivers.) 8 Tally Dascom 1125 Installation in progress. 7. 8. After installation is completed successfully, you will see the message on the right. 9 Tally Dascom 1125 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled. Adjusting the Print Gap Lever The print gap lever is on the left side of the printer inside the top cover. Take care to adjust the print gap lever to a suitable position whenever you change the number of copies being printed. Using the wrong print gap may cause print head damage or paper jams. Paper type Weight (g/m2) / ply Thickness (mm) Gap lever position Single sheet 2-ply 3-ply 4-ply 5-ply Change ribbon 52100 4052 4052 4052 4052
---
1P2P 3P4P 5P 0.060.12 0.120.14 0.170.22 0.230.27 0.280.33 Above 0.45 10 Tally Dascom 1125 There are 2 paper feed modes: friction feed and tractor feed. Friction Feed Handling 1. Move the paper-feed lever forward to for friction feed mode. 2. Adjust the print gap lever if necessary. 3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen. 4. 5. The paper should advance automatically to the print position. The printer is now ready to print in the online state. 11 Tally Dascom 1125 Tractor Feed Handling 1. Move the paper-feed lever backward to for continuous paper position. 2. Adjust the print gap lever if necessary. 3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In the same way, install the paper on the right tractor. 4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut. Push the right lock lever down to secure the right tractor in place. 5. Press theLoad/Ejectkey to load the paper to the starting print position. The printer is now ready to print in the online state. 12 Tally Dascom 1125 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60 cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm. 13 Tally Dascom 1125 4 Control Panel Operation There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are described below. LED Indicators Power/Paper Out LED:
On: Power on Flashing: Paper out Flashing + buzzer: Paper jam Online LED:
On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. Flashing: The printer is in setup state and cannot receive data. Tear Off LEDs:
Flashing: Indicates continuous paper is at tear-off position; otherwise it indicates the selected font. Control Panel Keys Online Key:
This key switches the printer between online and offline states. Printing is stopped when the printer is switched to offline state. When printer is switched to online state again, printing will resume. When printer is offline, pressing it for 3 seconds or longer will enter the setup state. This is indicated by a beep sound and the flashing Online LED. By pressing the Online key again will exit the setup state back to offline state. Load/Eject Key:
When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper
(continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting print position. In the setup state, this key performs a forward micro feed. 14 Tally Dascom 1125 LF/FF Key:
Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). In the setup state, this key performs a reverse micro feed. Tear Off Key:
When online, this key will move any loaded continuous paper to the tear-off position. When in setup state, this key is used to select the desired font. Table 4.1 Font Selection Label Draft Draft Condensed Roman Sans Serif Courier Prestige Script Others (see Menu setting) Tear Off Table 4.2 Switch S1 S2 S3 S4 Table 4.3 LED L3 L4 L2 State Off Flash On Off Flash On Off ON Flash Bottom Label Font Micro Feed Micro Feed 3sec L1 State Off Off Off On On On Flash Flash Flash Top Label Tear Off LF/FF Load/Eject Online Label Power/Paper Out Online 15 Tally Dascom 1125 Panel Operation There are 3 states of operation: Online, Setup and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, clear buffer and switch to offline state for access to Setup state. In the Setup state, the keys provide font selection and micro feed functions. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer. This state provides the following functions: Language Setup, Main Menu setup, Hex-dump, print Main Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update. The followings describe the 3 states in details. Legend:
[A] = press and hold switch A
{B} = press and then release switch B
[A]+ {B} = press switch B while holding A 16 Tally Dascom 1125 Online State Function Name Switch Operation LED Function Description Tear Off
{S1}
L1, L2 flash LF FF
{S2}
[S2]
Load/Eject
{S3}
-
-
-
This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts on the next TOF by:
pressing S1 once, or
receiving print data from the host. Feeds a line with every press of S2. By holding S2, the printer initially feeds a few lines; then feeds the form to the next TOF for rear tractor or ejects the form for cut sheets.
Load: Automatically loads the paper (according to path selection) when no paper is on the platen.
Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE:
Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. Setup state
[S4] > 3 secs L4 Toggles to Setup state. Indicated by flashing L4. Clear Buffer
[S4]+{S1}
[S4]+[S1] for longer time Reset
-
-
Clears the print buffer and beeps once when completed. Initializes the printer to the factory default settings. Beeps 3 times when completed. 17 Tally Dascom 1125 Setup State Function Name Switch Operation LED Function Description Online state
{S4}
Micro Up Micro Down Font Select
{S3}
{S2}
{S1}
L4
-
-
L1, L2 Toggling to the Online state will cause the printer to go into a ready-to-print state. Any changes made in Setup state will be saved permanently. Lighting up L4 indicates the Online state. Feeds up in 1/360 steps until the release of S3. Feeds down in 1/360 steps until the release of S2. Refer to Table 4.1 for details. 18 Tally Dascom 1125 Power-On State Function Name Status Page /
Self Test Switch Operation LED
[S4]
-
Hex Dump
[S3]
L4 Firmware Update
[S1]+[S2]+
[S3]+[S4]
L1, L2, L3, L4 Function Description Prints the printer settings and self-test pattern. Pressing S1 can change the font. Beeps once to indicate going into hex dump mode:
Prints data from host in hexadecimal representation.
Lights up L4.
Pressing S4 suspends the printing.
When the hex dump has finished, pressing S4 forces the printing of the last line of data, as any line termination control code from host has no function.
Pressing S1 can change the font.
Switch off the power to terminate the hex dump.
Alternate flashing of L3 and L4 indicates printer is ready for firmware update. L1 and L2 are ON and OFF respectively.
When new firmware is being received, L3 and L4 are set to ON. L1 flashes a few times and then sets to ON. L2 flashing indicates downloading in progress.
When downloading is completed, the carriage returns to home position. Printer initializes normally. 19 Tally Dascom 1125 Adjust Physical Margins
[S3]+[S4]
Service Menu
[S1]+[S2]
L1, L2, L3, L4 Restore Factory Defaults
[S2]+[S3]+[S4]
L1, L2, L3, L4 Menu Setup /
EDS
[S1]
[S2]+[S3]
Language Setup Language Setup
Flashing of L3.
Lights up L4.and L3.
Lights up L1 or L2 according to current fonts.
Includes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position
Flashing of L3.
Lights up L4.and L3.
Lights up L1 or L2 according to current fonts.
Functions are: Vertical Alignment, Change Pin, and Endless Self-Test.
Flashing of L3 then extinguish.
Lights up L4.
Lights up L1 or L2 according to current fonts.
Restore Factory Defaults parameters except Change Pin, Vertical Alignment and Adjust Page Margin Parameters Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Allows user to select one of the following languages:
English, German, Russian, Italian, French, Spanish and Turkish. Factory default is English. Refer to Language Setup section below for details. The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and
[Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current configuration is printed, and this is followed by Main Menu Setup. Below is an example of changing from English to German language:
20 Tally Dascom 1125 5 Printer Setting Changes To meet your own print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will print out the current settings and then enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off. The Main Menu is grouped into 5 sub-menus: System Setup, Page Setup, Print Setup, Interface Setup and Advanced Setup. A detailed description of the sub-menus is given below. The settings in bold and italic refer to the default settings. The settings below are provided in the following order of languages: English, German, Russian, Italian, French, Spanish and Turkish. System Setup System Setup Emulation Auto CR
(IBM) Auto LF Valid Settings ESC/P2, IBM 2390 Plus Yes, No Yes, No Print Dir Bi-Dir, Uni-Dir, Auto Top Print Dir Impact IBM AGM Bi-Dir, Uni-Dir Normal, Heavy Yes, No Print Setup Print Setup Function Selects the printer emulation. This should be the same as the host printer driver. Yes: LF = LF+CR; No: LF = LF
(Applies to IBM emulation only) Yes: CR = CR+LF; No: CR = CR Auto: Text & graphics in bi-direction; double height in uni-direction. Uni-Dir: Prints everything in uni-direction. Bi-dir: Prints everything in bi-direction. Note: Top position print direction may be affected by Top Print Dir setting. Bi-dir: Prints top position according to Print Dir setting. Uni-dir: Prints top position in uni-direction regardless of Print Dir setting. Heavy: Higher impact force for multipart printing Selects the IBM graphic mode. Applies to IBM emulation only Valid Settings Font (Others) OCR-B, OCR-A, ORATOR, GOTHIC, SOUVENIR Pitch 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0, 21 Function The setting here will only be active when Font is set to Others on control panel, Controls the characters per inch setting. Selects slashed or no-slash zero. On: Prints High Speed Draft when Draft font is selected. When printing 180x180 DPI graphics: Normal prints in 180x180 DPI, Fast prints in 90x180 DPI, Ultra prints in 60x180 DPI. Selects the IBM character set. 1: Normal; 2: Extended 14+1 international character set selections. National code page selections. Tally Dascom 1125 HS-Draft On, Off Graphic Speed Normal, Fast, Ultra IBM Set 1/2 Set 1, Set 2 Int'l Char Set USA, France, Germany, UK, Denmark, Sweden, Italy, Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal Code Page 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 22 Tally Dascom 1125 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 Character Table Graphic Table, Italic Table Page Setup Page Setup Line Per Inch Fanfold Form Length Valid Settings 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Fanfold Top Margin 0/60" 10/60"99/60"
Fanfold Bottom Margin 0/60"10/60"...30/60"
Single Form Length 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Single Top Margin 0/60" 10/60"99/60"
Single Bottom Margin 0/60"10/60"...30/60"
Roll Paper Yes, No Perforation Skip Yes, No Character table type selection. Function Sets the line spacing Sets the page length for tractor mode Sets the top margin for tractor mode. Due to mechanical tolerance, 0/60 is not guaranteed. Sets the bottom margin for tractor mode. Due to mechanical tolerance, 0/60 is not guaranteed. Sets the page length for friction mode Sets the top margin for friction mode. Due to mechanical tolerance, 0/60 is not guaranteed. Sets the bottom margin for friction mode. Due to mechanical tolerance, 0/60 is not guaranteed. In friction mode, [LF/FF] will not eject the paper and feed to next page. (Assume roll paper) Skips printing on perforation area 23 Tally Dascom 1125 Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5s View1s, View2s, View3s Specifies the waiting time before feeding the page to tear-off position automatically. Manual:
Auto tear mode is off. View1s, View2s, View3s:
After printing is completed, the printer will feed the paper until the last printed line is at the tear-off position. (Applies to tractor mode only) Interface Setup Interface Setup Interface Valid Settings Auto, Parallel, USB, Serial Yes, No Xon/Xoff, DTR RAM Usage User Font, Buffer I-PRIME Protocol Data Length Stop Bit Parity 8, 7 1, 2 None, Odd, Even 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s Baud Rate Auto IF Delay CX Bid Yes, No Advanced Setup Function For multi-host connection. Auto: First come first served;
Parallel/USB/Serial: Serves the designated host only. User Font: Part of RAM is used for user download characters;
Buffer: Disables user character download function; uses RAM for expanded buffer size up to 68KB. Yes: Host I-Prime signal resets the printer. Serial RS-232C communication protocol selection. Number of data bits per data byte selection. Number of stop bits per data byte selection. Selects the parity check mode. Selects the baud rate (transmission speed). Determines the waiting time before receiving data from another interface. Yes: Sets the parallel interface of the printer to bidirectional mode (IEEE 1284, Nibble mode), e.g. for Windows Plug & Play. No: Sets the interface to compatibility mode in order to ensure reliable operation with special external boxes. Advanced Setup Valid Settings Function Auto Load Manual, 0.5s, 1s, 1.5s, 2s Paper Jam Prevention Yes, No Paper End Detect Yes, No Specifies the waiting time before loading a cut sheet automatically. Manual: Auto load mode is off. (Applies to friction mode only.) Flattens paper edges by carriage movement before printing starts. Yes: Detects paper out and halts printing;
otherwise, ignores paper out and continues 24 Tally Dascom 1125 Software, Ignore Software, Ignore Software, Ignore Software, Ignore Yes, No Form Length Ctrl Pitch Ctrl Font Ctrl Quality Ctrl Buzzer German (Deutsch) printing. Ignore: Ignores form length commands Ignore: Ignores CPI commands Ignore: Ignores font select commands Ignore: Ignores print quality commands Yes: Sounds buzzer on all hardware errors System Setup Valid Settings Emulation Auto CR (IBM) Auto LF Druck Dir Top Druck Dir Anschlag IBM AGM ESC/P2, IBM 2390 Plus Ja, Nein Ja, Nein Bi-Dir, Uni-Dir, Auto Bi-Dir, Uni-Dir Normal, Stark Ja, Nein Druck Setup Valid Settings Font (Andere) Zeichenteilung Null HS-Draft Graphikgeschw. IBM Set Land Zeichensatz Zeichentabelle OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS 0, An, Aus Normal, Schnell, Ultra Set 1, Set 2 USA, Frankreich, Deutschland, UK, Dnemark, Schweden, Italien, Spanien, Japan, Norwegen, Dnemark II, Spanien II, Latein-Amerika, Korea, Legal CP 437, CP 857 Graphik, Italic Seiten Setup Valid Settings Zeilen Pro Zoll Endlos Formularlnge Endlos Oberer Rand Endlos Unterer Rand Einzel Formularlnge Einzel Oberer Rand Einzel Unterer Rand Rollenpapier 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
Ja, Nein 25 Tally Dascom 1125 Perforationssprung Abreissen Ja, Nein Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Schnittstellen Setup Valid Settings Schnittstelle I-PRIME Protokoll Datenlnge Stopp Bit Parity Baud Rate Auto IF Delay RAM Nutzung CX Bid Auto, Parallel, USB, Serial Ja, Nein Xon/Xoff, DTR 8, 7 1, 2 None, Odd, Even 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s Ladbarer Font, Puffer Ja, Nein Erweitertes Setup Valid Settings Auto Laden Papierstau Vorbeugung Papierende Detekt Formularlnge Strg Zeichenteilung Strg Font Strg Qualitt Strg Summer Russian ()
CR (IBM)
LF
.
IBM AGM Manuell, 0.5s, 1s, 1.5s, 2s Ja, Nein Ja, Nein Software, Ignoriere Software, Ignoriere Software, Ignoriere Software, Ignoriere Ja, Nein Valid Settings ESC/P2, IBM 2390 Plus
,
,
, ,
,
,
,
Valid Settings
/
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS 0,
, 26 Tally Dascom 1125
IBM 1/2
, ,
. 1, . 2 USA, France, Germany, UK, , Sweden, Italy, Spain, Japan, , II, Spain II,
, Korea, Legal CP 437, CP 857
,
Valid Settings 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
,
,
, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Valid Settings
.
RS-232
-
RAM CX Bid
, , USB, RS-232
, Xon/Xoff, DTR 8, 7 1, 2
, , 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s
. ,
,
Valid Settings
.
, 0.5s, 1s, 1.5s, 2s
,
, 27 Tally Dascom 1125
/
Italian (Italiano)
, .
, .
, .
, .
, Menu Sistema Valid Settings Emulazione Auto CR (IBM) Auto LF Direz. Stampa Top Print Dir Impatto IBM AGM ESC/P2, IBM 2390 Plus Si, No Si, No Bi-Dir, Uni-Dir, Auto Bi-Dir, Uni-Dir Normale, Pesante Si, No Men Stampa Valid Settings Fonte (Altre) Spaziatura Zero HS-Bozza Veloc. Grafica IBM Set 1/2 Set Carat. Int. Code Page Tab.Carattere OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS 0, Si, No Normale, Veloce, Ultra Set 1, Set 2 USA, Francia, Germania, Regno Unito, Danimarca, Svezia, Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II, America Latina, Korea, Legal CP 437, CP 857 Tab. Grafica, Italico Men Pagina Valid Settings Interlinea Lungh. Mod. Continuo Margine Sup. Continuo Margine Inf. Continuo Lunghezza Foglio Margine Sup. Foglio Margine Infer. Foglio Rullo Carta Salto Perforazione Autostrappo 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
Si, No Si, No Manuale, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s 28 Tally Dascom 1125 Men Interfacc. Valid Settings Interfaccia I-PRIME Protocollo Lunghezza dati Stop Bit Parit Velocit Ritardo Auto IF Uso RAM CX Bid Auto, Parallela, USB, Seriale Si, No Xon/Xoff, DTR 8, 7 1, 2 No, Dispari, Pari 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s Fonti utente, Memoria Si, No Men Avanzato Valid Settings Autocaricamento Previene Inceppamento Rileva Fine Carta Control. Lungh. Carta Control. Spaziatura Controllo Fonti Controllo Qualit Cicalino French (Franais) Manuale, 0.5s, 1s, 1.5s, 2s Si, No Si, No Software, Ignora Software, Ignora Software, Ignora Software, Ignora Si, No Setup systme Valid Settings Emulation RC-Auto (IBM) SL-Auto Dir Impr. Sup. Dir Impr. Frappe IBM AGM ESC/P2, IBM 2390 Plus Oui, Non Oui, Non Bidir, Unidir, Auto Bidir, Unidir Normal, Forte Oui, Non Setup impression Valid Settings Polices (Autres) Densits caract. Zro HS-Draft Vitesse graphiq. IBM Set 1/2 Pays OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS 0, Oui, Non Normal, Rapide, Ultra Set 1, Set 2 USA, France, Allemagne, Royaume-Uni, Denmark, Sude, Italie, 29 Tally Dascom 1125 Jeu de caractr. Tabl.de caract. Espagne, Japon, Norvge, Denmark II, Espagne II, Amerique latine, Korea, Legal CP 437, CP 857 Graphque, Italique Setup page Valid Settings Lignes par pouce 1, 2, 3, 4, 5, 6, 7, 8 Papier continu Longueur formulaire 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Papier continu Bord suprieure Papier continu Bord infrieure 0/60" 10/60"99/60"
0/60"10/60"...30/60"
Feuille feuille Longueur formulaire 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Feuille feuille Bord suprieur Feuille feuille Bord infrieur Papier du rouleau Sauter la perforation Coupe Auto 0/60" 10/60"99/60"
0/60"10/60"...30/60"
Oui, Non Oui, Non Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Setup interface Valid Settings Interface I-PRIME Protocole Long. de donnes Bits darrt Parit Vitesse baud Auto IF Delay Utilisation RAM CX Bid Auto, Parallel, USB, Serial Oui, Non Xon/Xoff, DTR 8, 7 1, 2 None, Odd, Even 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s User Font, Buffer Oui, Non Setup largi Valid Settings Chargem. Autom. Prvention bourrage Dtec.fin de pap Long.formul.Strg Densi.caract.Strg Police Strg Qualit Strg Vibrateur Manuel, 0.5s, 1s, 1.5s, 2s Qui, Non Qui, Non Software, Ignorer Software, Ignorer Software, Ignorer Software, Ignorer Qui, Non 30 Tally Dascom 1125 Spanish (Espaol) System Setup Valid Settings Emulacin Auto CR(IBM) Auto LF ModoImpresin ModoImp.Borde Impacto IBM AGM ESC/P2, IBM 2390 Plus Si, No Si, No Bi-Dir, Uni-Dir, Auto Bi-Dir, Uni-Dir Normal, Fuerte Si, No Print Setup Valid Settings Fuente (Otros) Tamao Letra Cero Alta Velocidad Imp. Grafica IBM Juego 1/2 Carcter Local Tabla Carcter Tipo Tabla Page Setup Lineas Por Pulgada Tamao Papel Continuo Margen Sup. Pap Cont. Margen Inf. Pap.Cont. Tamao Hojas Sueltas Margen Sup. Folios Margen Inf. Folios Rollo de Papel Salto perforacin OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS 0, Activado, Desactivado Normal, Rpido, Ultra Juego 1, Juego 2 USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia, Espaa, Japn, Noruega, Dinamarca II, Espaa II, AmricaLatina, Corea, Legal CP 437, CP 857 Tabla Grfica, Italica Valid Settings 1, 2, 3, 4, 5, 6, 7, 8 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
Si, No Si, No Mover a PosicinCorte Manual, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Interface Setup Valid Settings Interface I-Prime Auto, Paralelo, USB, Serie Si, No 31 Tally Dascom 1125 Protocolo LongitudDatos Bit Parada Paridad Tasa Baudios Auto retraso Uso de RAM CX Bid Xon/Xoff, DTR 8, 7 1, 2 Ninguna, Impar, Par 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s Font Usuario, Buffer Si, No Advanced Setup Valid Settings Auto Carga Prevencin Atascos Deteccin Fin Papel Control Tamao Papel Control Tamao Letra Control Fuente Control Calidad Alarma Turkish (Trkce) Manual, 0.5s, 1s, 1.5s, 2s Si, No Si, No Software, Ignorar Software, Ignorar Software, Ignorar Software, Ignorar Si, No Sistem Ayar Valid Settings Benzetim/Emulation Otom. Satrba (IBM) Otom. Satr besleme Yazdrma yn stte yazdrma yn Vuru IBM AGM ESC/P2, IBM 2390 Plus Evet, Hayr Evet, Hayr
ki-Yne, Tek-Yne, Otom.
ki-Yne, Tek-Yne Normal, Gl Evet, Hayr Yazdrma Ayarlar Valid Settings Yaz Tipi (Dier) Karakter Skl Sfr Yk.Hz-Taslak Grafik Hz IBM Karakter Seti 1/2 Uluslararas Kar. Seti Kod Sayfas OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS 0, On, Off Normal, Hzl, Ultra Set 1, Set 2 Amerika Bir.Devleti, Fransa, Almanya, ngiltere, Danimarka,
sve, talya, spanya, Japonya, Norve, Danimarka II, spanya II, Latin Amerika, Korea, Legal CP 437, CP 857 32 Tally Dascom 1125 Karakter Tablosu Grafik Tablosu, talik Sayfa Dzeni Ayar
n bana satr Srekli-kat Form Uzunluu Srekli-kat st kenar boluu Srekli-kat Alt kenar boluu Tek-kat Form uzunluu Tek-kat st kenar boluu Tek-kat Alt kenar boluu Rulo kat Delik atlama Otom. Koparma 1, 2, 3, 4, 5, 6, 7, 8 Valid Settings 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
0/60" 10/60"99/60"
0/60"10/60"...30/60"
Evet, Hayr Evet, Hayr Elle/Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Arabirim Ayarlar Valid Settings Arabirim I-Prime
letiim Kurallar Veri Uzunluu Durma Biti Elik Otom., Paralel, USB, Seri Evet, Hayr Xon/Xoff, DTR 8, 7 1,2 Yok, ift, Tek Baud Hz Otom. Arabirim gecikmesi 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 10s, 30s RAM Kullanm CX Bid Kullanc Yaz Tipi, Arabellek Evet, Hayr Gelitirilmi Ayarlar Valid Settings Otom. Ykleme Kat Skmasn nleme Kat Sonunu Alglama Form Uzunl. Kont. Karak.Skl. Kont. Yaz Tipi Kont. Kalite Kont. Alarm Zili Elle/Manuel, 0.5s, 1s, 1.5s, 2s Evet, Hayr Evet, Hayr Yazlm, Yoksay Yazlm, Yoksay Yazlm, Yoksay Yazlm, Yoksay Evet, Hayr 33 Tally Dascom 1125 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure:
1. Enter the Service Menu by holding down theTear/OffandLF/FFkeys while powering up. 2. Load paper. 3. The printer will print as follows:
Service Menu
LF/FF= OK Tear/Off= Back Load/Eject= Next Online= Exit Current SettingVertical Alignment 4. PressLF/FFkey to select the current setting. The printer will print as follows:
Vertical Alignment
LF/FF= OK Tear/Off= Back Load/Eject= Next Online= Exit Please select Paper TypeSingle Ply 5. 6. For single ply paper, pressLF/FFkey to select. For multipart paper, press Load/Ejectkey to go to Multipartthen pressLF/FFkey to select. If single ply is selected for paper type, the following will print:
Single Ply Current Print Mode: LQ Press Load/Ejectkey to scroll to other print modes if required. If LQ is selected, the following will print:
LQ
LF/FF= lower to left Load/Eject= lower to right Online= Exit LQ -2:
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Pressing LF/FFor Load/Eject key will allow you to adjust the alignment of the vertical lines 34 Tally Dascom 1125 printed above. 7. Once the setting which gives the best alignment is found, press Online key to exit current level. Printer will print Save settings? Yes. Press LF/FF key to save setting. Press Online key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail. The Change Pin function enables the user to continue using the printer for a while without compromise in print quality until a suitable print head replacement is available. This function will reduce the print speed if activated. Change Pin Procedure:
1. Enter the Service Menu by holding down theTear/OffandLF/FFkeys while powering up. 2. Load paper. 3. The printer will print as below:
Service Menu
LF/FF=OK Tear/Off= Back Load/Eject= Next Online= Exit Current MenuVertical Alignment Press Load/Eject key to scroll to Change Pinthen press LF/FF key to select. The status of each pin will be printed as follows:
Change Pin 1 ---------- Is this pin OK? Yes / No 2 ---------- Is this pin OK? Yes / No 3 ---------- Is this pin OK? Yes / No
:
24 ---------- Is this pin OK? Yes / No Press Load/Eject key to choose whether the pin is Yes or Nothen press LF/FF key to confirm selection. 4. When all the 24 pins are evaluated, press Online. The printer will print Save settings? Yes. Press
LF/FF key to confirm selection. Press Online key a few times until the printer exits the Service Menu. 35 Tally Dascom 1125 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure:
1. Enter the Adjust Page Margins function by holding down theLoad/EjectandOnlinekeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below:
Adjust Page Margins:
LF/FF=OK Tear/Off= Back Load/Eject= Next Online= Exit Current Setting: Adjust Fanfold Top Margin PressLF/FFkey to confirm selection if the paper used is fanfold type. The printer will print as follows:
Procedure Install fanfold paper to tractors
LF/FF = Add Load/Eject = Reduce Online = Exit Each step is 0.5 mm Function of keys:
Tear Offkey: Decrease 0.5mm
Load/Ejectkey: Increase 0.5mm 4. Press LF/FF key, printer will print Save settingsYes. Press Load/Eject key to choose Yes or Nothen press LF/FF key to confirm selection and exit Adjust Page Margins mode by pressing Online. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Left Margin Procedure:
1. Enter the Adjust Page Margins function by holding down theLoad/EjectandOnlinekeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below:
Adjust Page Margins:
LF/FF=OK Tear/Off= Back Load/Eject= Next Online= Exit Current Setting: Adjust Fanfold Top Margin 4. PressLoad/Ejectkey until the current setting is Adjust Fanfold Left Margin. PressLF/FFkey to confirm selection if the paper used is fanfold type. The printer will print as follows:
Adjust Fanfold Left Margin 0 36 Tally Dascom 1125 Function of keys:
Tear Offkey: Decrease 0.5mm
Load/Ejectkey: Increase 0.5mm 5. Press LF/FF key, printer will print Save settingsYes. Press Load/Eject key to choose Yes or Nothen press LF/FF key to confirm selection and exit Adjust Page Margins mode by pressing Online. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure:
1. Enter the Adjust Page Margins function by holding down theLoad/EjectandOnlinekeys while powering up until the printer beeps twice. 2. Load fanfold paper. 3. The printer will print as below:
Adjust Page Margins:
LF/FF=OK Tear/Off= Back Load/Eject= Next Online= Exit Current Setting: Adjust Fanfold Top Margin 4. PressLoad/Ejectkey until the current setting is Adjust Tear-Off Position. PressLF/FFkey to confirm selection. The printer will print as follows:
Procedure Install fanfold paper to tractors
LF/FF = Add Load/Eject = Reduce Online = Exit Each step is 0.5 mm Function of keys:
Tear Offkey: Decrease 0.5mm
Load/Ejectkey: Increase 0.5mm 5. Press LF/FF key, printer will print Save settingsYes. Press Load/Eject key to choose Yes or Nothen press LF/FF key to confirm selection and exit Adjust Page Margins mode by pressing Online. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. 37 Tally Dascom 1125 Dascom Printer Setup Tool In the CDROM is a software utility called Dascom Printer Setup. This application enables a convenient, simple and fast way to control your printer without touching any keys on the operation panel. 1. Start the tool installation by double clicking the Dascom Printer Setup.exe. 2. Connect the printer to the system using USB cable 3. Power up the printer. 4. Load paper into the printer. (Note: The tool cannot get connected to the printer when the printer is offline.) 5. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup, and then Tally Dascom Printer Setup. 6. For more information on how to use the tool, go to the Help menu and select User Guide. 38 Tally Dascom 1125 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer to determine whether lubrication may be necessary. Switch printer off and unplug the power cord from the mains before doing any maintenance work. Cleaning The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover is open. Cleaning and Vacuuming the Printer If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the printer, clean the printer. To clean and vacuum the printer:
1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer power cord. 2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge. 3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer. 4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends from the print head carriage. 5. Re-install the ribbon cartridge. 6. Remove the single sheet feeder and clean the form tractors and the surrounding areas. 7. Re-install the single sheet feeder. Cleaning the Paper Rollers Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to harden. To clean the rollers and the platen:
1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer. 2. Place the cloth against the platen and manually rotate the paper feed knob. 3. Repeat this procedure for each roller. 39 Tally Dascom 1125 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob. 40 Tally Dascom 1125 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution Printing is too light or too dark. Smears and stains appear on the page. Printing is erratic or the wrong characters are printed. Many ?
or unexpected characters are printed. The page is blank. Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly. Replace the ribbon if necessary. Make sure that the print gap lever is set for the thickness of your paper. Make sure that the print gap lever is set for the thickness of your paper. Check for ribbon wear. Replace the ribbon if necessary. Check whether the tip of the print head is dirty. Clean the head with a soft cloth if necessary. The print head may need to be replaced. Make sure that the interface cable is securely connected to both the printer and computer. Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. Check the length of the interface cable. (Maximum Parallel &
USB: 2 meters, Serial: 15 meters) Try another interface cable. Make sure that the ribbon cartridge is properly installed. Make sure the gap lever is set correctly. Printing is vertically misaligned
(jagged). Use the printer's vertical alignment function to check the vertical print alignment. If necessary, adjust the print alignment. The top margin is wrong. Lines are double spaced instead of single spaced. The printer overprints on the same line. The next print line starts where the previous line ended instead of at the left margin. Check the application top margin setting. Adjust the Top Margin setting in Page Setup menu if necessary. Change the Auto LF setting in the System Setup menu to No. Change the Auto CR setting in the System Setup menu to No. Change the Auto CR setting in the System Setup menu to Yes. 41 Tally Dascom 1125 Paper Handling Problems and Solutions Problem Solution Paper cannot be loaded or fed. Paper jams while loading. Paper jams while printing. Make sure that the paper select lever located on the top right of the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. Make sure that the paper covers the paper-out sensor. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Make sure that the Print Gap lever is set for the thickness of your paper. Make sure that the paper is not folded, creased, or torn. Make sure that the left and right tractors are set so that the continuous forms are stretched taut. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Make sure that the Print Gap lever is set for the thickness of your paper. For continuous forms, make sure that the incoming and outgoing paper stacks are correctly placed. Paper should feed straight. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Make sure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor pins. Operating Problems and Solutions Problem Solution The power does not turn on. Check whether the mains voltage is correct. Make sure that the power cord is securely connected to both the printer and the mains power outlet. Make sure that the power outlet is functional. If not so, use other outlet. Turn the power off. Wait a minute and then turn the printer on again. If the printer still has no power, contact your dealer. 42 Tally Dascom 1125 The printer is on but it will not print. Paper select lever error Printer Failures Make sure that the Online indicator is lit. If you use the interface cable, make sure it is securely connected to both the printer and the computer. Make sure paper is loaded. Run the printer Status Page. If printing executes normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings. Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position. A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner. Online LED Tear Off LED Buzzer Sound Off Off Off Flash Off Off Flash Flash No change Flash Flash Once Once Continuously No change
--
Flash Flash No change Flash Once
--
Once
--
Error Indications on LEDs Error Description Paper out Paper jammed Operation Status Normal Paper Out LED Flash Suspend Flash Friction feed /Tractor feed Suspend Print head hot Carriage initial position Memory EEPROM CMOS chip Normal Stop Stop Normal Stop On On Off Off Off Off 43 Tally Dascom 1125 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment.
Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.
HEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps.
PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printers vertical line print alignment in bi-directional mode. For details on using these functions, please refer to chapters 4 and 5. 44 Tally Dascom 1125 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person. To load new firmware, proceed as follows:
1. Switch off the printer. Connect your PC to the parallel port on the printer. 2. Press and hold down all 4 keys (S1, S2, S3, S4) while powering on the printer. 3. Alternate flashing of L3 and L4 LEDs indicates printer is ready for firmware update. L1 and L2 LEDs are ON and OFF respectively. 4. Go to the DOS prompt window. Copy the firmware file (with extension .MOT) to your printer as follows:
COPY /B <filename>.mot PRN 5. When new firmware is being received, L3 and L4 LEDs are set to ON. L1 LED flashes a few times, then sets to ON. L2 LED flashing indicates downloading in progress. Note: Do not interrupt the downloading process to prevent possible flash memory corruption. 6. When downloading is completed, the carriage returns to home position. Printer initializes normally. Alternatively, you can use the Firmware Flash Tool version 3.5 or higher which is available in the CDROM and our website as well. Upon starting up the tool, choose the correct file and press "Update". 45 Tally Dascom 1125 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Pitch 10 CPI 12 CPI 15 CPI 17.1 CPI 20 CPI HS Draft 375/80H 300/120H 375/120H 426/120H 498/120H Draft 250/120H 300/120H 375/120H 426/120H 498/120H LQ 83/360H 100/360H 125/360H 142/360H 166/360H
(CPS/DPI) LQ Draft HS Draft Pitch 8x24/80H 12x24/120H 36x24/360H 10 CPI 10x24/120H 10x24/120H 30x24/360H 12 CPI 8x16/120H 24x16/360H 8x16/120H 15 CPI 7x24/120H 21x24/360H 7x24/120H 17.1 CPI 6x24/120H 18x24/360H 20 CPI 6x24/120H Proportional Nx24/360H Nx24/360H Nx24/360H
(Matrix/DPI) Number of pins: 24 pins Firing frequency: Normal mode: 1500 Hz Pin diameter: 0.2 mm Life: 400 million strokes/pin @ Draft mode 8-bit mode: 8V x 60H, 80H, 90H, 120H, 240H (DPI) 24-bit mode: 24V x 60H, 90H, 120H, 180H, 360H (DPI) Continuous feed: 5.0 IPS (inches per second) Print Speed Font Matrix Print Head Graphics Paper Feed Speed Resolution 360 x 360 DPI maximum Printable Columns Characters per line (CPL) 10 CPI: 80 CPL 12 CPI: 96 CPL 15 CPI: 120 CPL 17.1 CPI: 137 CPL 20 CPI: 160 CPL 46 Tally Dascom 1125 Bitmap Fonts:
1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI 6. OCR-B 10, 12, 17, 20 CPI 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI Interleaved 2 of 5 1. EAN-13 2. EAN-8 3. 4. UPC-A 5. UPC-E 6. Code 39 7. Code 128 8. POSTNET 9. Codabar 10. Industrial 2 of 5 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254 47 Built-In Fonts Barcodes Code Pages Tally Dascom 1125 Code Pages International Character Sets 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. 8. Spain I 9. Japan 10. Norway 11. Denmark II 12. Spain II 13. Latin America 14. Korea 15. Legal Italy 48 Tally Dascom 1125 Line Spacing 1/6", 1/8", n/60", n/180", n/360"
Paper Specifications Paper Specifications Cut Sheet Width:
76.2mm256.5mm
3"10.1" Length:
101.6mm363.2mm
3.9"14.3" Weight: 52100g/ Thickness:
0.0650.14mm
(0.0026"0.0055) Fanfold Paper Single ply Multi-part Width: 76.2mm254mm (3"10" Length: 101.6mm min (4" min) Weight: 52100 g/ Thickness:
0.0650.14mm
(0.0026"0.0055") Weight: 4058g/ Thickness: 0.45 mm max
(0.0177 max) Paper Handling Feeding method: Friction and Tractor Paper path: Cut sheets: Top load and top out Fanfold: Rear in and top out Copy Capability Original + 4 copies Emulation ESC/P2, IBM 2390 Plus Ribbon Type Cartridge; Monochrome Ribbon Life 7 million characters (rolling Draft 10 CPI) Input Data Buffer Up to 68KB Windows Drivers Interface Operation Panel Noise Level Ambient Conditions Windows Server 2000/2003/2008 Windows Vista Windows XP Windows 98 Windows 7 Parallel (Bi-directional IEEE-1284 nibble mode) USB 2.0 (B type connector) Serial RS-232C Switches: 4 pcs LED indicators: 4 pcs
< 51 dBA in 10CPI draft ASCII (Conforming to ISO7779) Temperature Operating: +5 to +40 C. Stand-by: -20 to +55 C Humidity Operating: 10 to 80%RH
(No condensation) Stand-by: 5 to 85%RH
(No condensation) Dimensions 359 mm (W) x 285 mm (D) x 159 mm (H) 49 Tally Dascom 1125 Weight Power Supply Power consumption MTTR MTBF Certification 5 kg Unit type:
Switching mode power supply Power cord:
Detachable Voltage rating:
AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by:
ESD:
Contact discharge: 4kV Air discharge:
8kV Less than 3.8W Comply with IEC801-2 28.2 W (standard ECMA-132)
< 20 minutes 10000 hours @ 25% duty cycle CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV, Microsoft Certified for Windows 7 50 Tally Dascom 1125 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin 1 2~9 10 11 12 13 14 15 16 17 18 19~30 31 32 33 34 35 36 Signal Name STROBE DATA ACK BUSY PE SELECT AFXT Unused GND F-GND
+5V GND INIT FAULT GND Unused FUSE SLCTIN Signal Transmission Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Unused Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Unused Printer Computer Printer Computer Parallel Interface Connector Diagram Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation. 51 Tally Dascom 1125 USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the B type USB connector. Serial Interface Serial RS-232C Interface Pin Assignment Pin Signal Symbol Signal Name 1 2 3 4 7 20 25 CG TXD RXD RTS SG DTR
+5V Chassis Ground Send Data Receive Data Request to Send Signal Ground Data Terminal Ready Power Serial RS-232 Connector Diagram Signal Transmission OUT IN OUT OUT 52 Tally Dascom 1125 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 53 Tally Dascom 1125 IBM Character Set 1 IBM Character Set 2 54 Tally Dascom 1125 International character sets International Character Set Commands Country USA France Germany UK Denmark1 Sweden Italy Spain1 Japan Norway Denmark2 Spain2 Lat America Korea Legal Command
ESCRCHR0
ESCRCHR1
ESCRCHR2
ESCRCHR3
ESCRCHR4
ESCRCHR5
ESCRCHR6
ESCRCHR7
ESCRCHR8
ESCRCHR9
ESCRCHR10
ESCRCHR11
ESCRCHR12
ESCRCHR13
ESCRCHR64 55 Tally Dascom 1125 Character Tables Italic 56 Tally Dascom 1125 Graphic 1 Graphic 2 57 Tally Dascom 1125 Code Page Commands Code Page ESC R Parameter CRO-ASCII Arabic Farsi Arabic Urdo Greek DEC Greek ELOT 928 CP437 Latin US CP737 Greek CP850 Latin 1 CP851 Greek CP852 Latin 2 CP857 Turkish CP858 (IBM with ) CP860 Portugal CP861 Icelandic CP863 French Canada CP864 Arabic CP864 Arab. Extended CP865 Nordic CP866 Cyrillic CP866 Bulgaria Siemens Turkish DEC Turkish CP1250 Win Latin 2 CP1251 Win Cyrillic CP1252 Win Latin 1 CP1253 Win Greek CP1254 Win Turkish 8859-1 Latin 1 8859-1 Latin 1 (SAP) 8859-2 Latin 2 8859-5 Cyrillic 8859-7 Greek 8859-9 Turkish 8859-15 Latin 9 (Euro) BRASCII Abicomp Roman 8 3C 96 97 46 6C 80 93 82 88 87 8D 9E 84 94 85 8C 95 86 8E 9D 9B 9C 70 71 72 73 74 25 2B 26 2A 2D 2E 2F 6D 6E 4D 58 Tally Dascom 1125 Coax/Twinax(Hebrew) New-437 (Hebrew) New-DIG 850 (Hebr.) Old-Code 860 (Hebr.) Flarro 863 (Hebrew) Table 865 (Hebrew) CP775 Baltic CP1257 Baltic Mazovia (Poland) Kamenicky (Czech) CP866 Ukraine CP866 Kazakhstan 4F 81 83 98 99 9A A6 77 92 91 8F 90 59 Tally Dascom 1125 Code Page Tables CP 437 (US) CP 737 Greek 60 Tally Dascom 1125 CP 850 (Multilingual) CP 851 61 Tally Dascom 1125 CP 852 (Eastern Europe) CP 857 (Turkish) 62 Tally Dascom 1125 CP 858 CP 860 (Portugal) 63 Tally Dascom 1125 CP 861 (Iceland) CP 863 (French-Canadian) 64 Tally Dascom 1125 CP 864 Arabic CP 864 Arabic Extended 65 Tally Dascom 1125 CP 865 (Norway) CP 866 (Cyrillic) 66 Tally Dascom 1125 CP 866 Bulgaria CP 1250 Win Latin 2 67 Tally Dascom 1125 CP 1251 Win Cyrillic CP 1252 Win Latin 1 68 Tally Dascom 1125 CP 1253 Win Greek CP 1254 Win Turkish 69 Tally Dascom 1125 8859-1 Latin 1 8859-1 Latin 1 (SAP) 70 Tally Dascom 1125 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 71 Tally Dascom 1125 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 72 Tally Dascom 1125 ISO 8859-15 Euro (Code Page 923) BRASCII 73 Tally Dascom 1125 Abicomp Roman 8 74 Tally Dascom 1125 Coax/Twinax (Hebrew) New-437 (Hebrew) 75 Tally Dascom 1125 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 76 Tally Dascom 1125 Flarro 863 (Hebrew) 865 Hebrew 77 Tally Dascom 1125 CP 1257 866 Ukraine 78 Tally Dascom 1125 866 Kazakhstan Kamenicky 79 Tally Dascom 1125 Mazovia CP 775 80 Tally Dascom 1125 CRO-ASCII Arabic Farsi 81 Tally Dascom 1125 Arabic Urdo Greek DEC 82 Tally Dascom 1125 Greek ELOT 928 83 Tally Dascom 1125 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC &
ESC ( ^ n m d1 d2 ESC (G NUL d ESC * m n1 n2 ESC . c v h m nL nH d1 d2 ESC + n ESC n ESC / n ESC ( C NUL n m ESC ( c NUL nt mt nb mb ESC ( U NUL n ESC 0 ESC 2 ESC 3 n ESC 4 ESC 5 ESC 6 ESC 7 Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Carriage return Select double-width printing (one line) Select condensed mode Online Cancel condensed mode Offline Cancel double-wide mode(one line) Cancel line Delete character Select double-width printing (one line) Select condensed mode Set intercharacter space NA Print mode setup Choose character lineation Select absolute horizontal print position Set left margin Select user-defined set Define user-defined set Print data in character style Select graphics mode Select image mode Print raster graphics Select n/360line spacing Underline on/off Select vertical orientation channel Set page length Page setup Set unit Set 1/8line spacing Set 1/6line spacing Set n/180line spacing Set Italic Cancel Italic Enable printable characters Enable upper control characters 84 Tally Dascom 1125 ESC :
ESC ESC >
ESC =
ESC #
ESC n m ESC @
ESC n1 n2 ESC A n ESC BNUL ESC C n ESC DNUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 ESC L n1 n2 ESC M ESC N n ESC O ESC P ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 ESC Z n1 n2 ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Copy ROM to RAM Unidirectional mode(1 line) Set MSB to 1 Set MSB to 0 Cancel MSB control Reassign graphics mode Initialize printer Set relative horizontal print position Set n/60line spacing Set/cancel vertical tabs Set page length in lines Set/cancel horizontal tabs Select Bold Cancel Bold Select double-strike mode Cancel double-strike mode Perform tactic n/180line feed Select 8 pins single-density graphics Select 8 pins doubledensity graphics Select ELITE12CPI Set bottom margin Cancel bottom margin Select PICA10CPI Set right margin International character set Select superscript/subscript Cancel superscript/subscript Select unidirectional/bidirectional printing mode Select absolute vertical print position Turn Double-wide mode on/off Select font by pitch and point Select 8 pins, high speed ,double density graphics Select 8 pins, high speed fourfold density graphics Select justification Select vertical orientation channel Set horizontal intercharacter space Select 15CPI Perform reverse n/180line feed Select typeface Turn proportional mode on/off Select character style Select printing colour Select character table Assign character table Set relative vertical print position Turn double-high mode on/off Select print quality Barcode print 85 Tally Dascom 1125 IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC :
ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC =
ESC \
ESC ^
ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Beeper Backspace Tab horizontally Enter Line feed Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Form feed Automatically Feed Paper mode Set 12CPI Tab vertically Select 1/8line spacing Select 7/72line spacing Select 1/6line spacing or activate ESC A n command Select n/216or 1/180line spacing Set top margin Automatic Line Feed Select character set 2 Select character set 1 NA Print continuously from all character chart Print single character from all character chart Select n/72or n/60line spacing Select Tab vertically Set page length in lines 86 Tally Dascom 1125 ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 Vn ESC L n1 n2 V1 V2 Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 Vn ESC Z n1 n2 V1 V2 Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\
ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ]
ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m Set page length in inches Select Tab horizontally Select bold Cancel bold Select double-strike mode Cancel double-strike mode Select printing mode Perform n/180or n/216single line feed Normal density graphics Dual-Density Bit Image Graphics (Half Speed) Select bottom margin Cancel bottom margin Set proportional intercharacter Offline Clear tab Select superscript/subscript Cancel superscript/subscript Select bidirectional printing on/off Select double-wide printing mode(continuous) Set left and right margin Select double -density graphics Select fourfold -density graphics Select line Select printing mode Select font and pitch Set initialization condition Set code page Set vertical unit Select printing quality Set barcode parameters Select high-density graphics printing Set barcode data Feed paper in reverse direction Print upper-line Print underline Move the current printing position Stop printing Select printing colour Select graphic mode If you need more details regarding the emulation commands, please contact us. 87 Tally Dascom 1125 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orientate or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 88 DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com UNITED KINGDOM DASCOM GB Ltd ViewPoint, Basing View, Basingstoke, Hampshire RG21 4RG, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com RUSSIA and CIS DASCOM Europe GmbH Representation Moscow Leninsky Prospekt 95a, Office 322 119313 Moscow, Russian Federation Phone: +7 (495) 984 70 65 Fax: +7 (495) 984 56 42 www.dascom.com AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980, USA Phone:+1 (877) 434 13 77 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 63 Hillview Avenue
#08-22, Lam Soon Industrial Building Singapore 669569 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com.sg FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. CEE DASCOM Europe GmbH Europaring F15 301 2345 Brunn a. G. Austria Phone: +43 (1) 236 01 70 10 www.dascom.com 2011 DASCOM Part No: 21.511.800.0042
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-03-13 | JBP - Part 15 Class B Computing Device Peripheral | Class II permissive change or modification of presently authorized equipment | |
2 | 2011-11-02 | JBP - Part 15 Class B Computing Device Peripheral | Change in identification of presently authorized equipment. Original FCC ID: ZIOTD11250 Grant Date: 08/10/2011 |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2014-03-13
|
||||
1 2 |
2011-11-02
|
|||||
1 2 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 2 | FCC Registration Number (FRN) |
0021247903
|
||||
1 2 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 2 |
Jiangmen City Guang Dong Province, N/A
|
|||||
1 2 |
China
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
k******@emcc.de
|
||||
1 2 |
t******@siemic.com
|
|||||
1 2 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
Z7O
|
||||
1 2 | Equipment Product Code |
TD11250
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
Y******** H****
|
||||
1 2 | Title |
Manager
|
||||
1 2 | Telephone Number |
0750-********
|
||||
1 2 | Fax Number |
0750-********
|
||||
1 2 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Dot Matrix Printer | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Change in identification of presently authorized equipment. Original FCC ID: ZIOTD11250 Grant Date: 08/10/2011 | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Dongguan Dongdian Testing Service Co.,Ltd
|
||||
1 2 |
SIEMIC (Nanjing-China) Laboratories
|
|||||
1 2 | Name |
J****** Y******
|
||||
1 2 |
L**** B******
|
|||||
1 2 | Telephone Number |
086-0******** Extension:
|
||||
1 2 |
86-25********
|
|||||
1 2 | Fax Number |
86-25********
|
||||
1 2 |
y******@163.com
|
|||||
1 2 |
l******@siemic.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | |||||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC