all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 2.94 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Users Manual | Users Manual | 2.94 MiB |
Tally Dascom 1140 I Tally Dascom 1140 Tally Dascom 1140 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operators Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances. Ensure the printer is connected to a socket with the correct mains voltage. Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Make sure that the printer and computer are switched off before connecting the data cable. The print head will become very hot during printing; avoid contact with the print head after printing has finished. Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. The device and mains-socket must all times be easily accessible. I Tally Dascom 1140 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Stoffen auf. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Keine Flssigkeiten mit dem Drucker in Berhrung bringen. Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit abkhlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. Maschinenlrminformations Verordnung 3.GPSGV, der hchste Schalldruckpegel betrgt 70 dB(A) oder weniger gem EN ISO 7779. Das Gert und die Netzsteckdose mssen jeder Zeit leicht zugnglich sein. II Tally Dascom 1140 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service. Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un dpanneur qualifi. Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber. Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de substances explosives. Ne connecter limprimante une prise que lorsque la tension est correcte. Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension et toujours dbrancher le connecteur secteur de la prise murale. Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la poussire. Ne pas mettre limprimante en contact avec des liquides. Ne pas exposer limprimante des chocs, impacts ou vibrations. Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de donnes. La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir quelques instants avant dy toucher. N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. Le dispositif et la prise principale doivent toujours tre accessibles facilement. III Tally Dascom 1140 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere. Evitare il contatto della stampante con liquidi. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili. IV Tally Dascom 1140 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un tcnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sunstancias explosivas. Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentacin del enchufe. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegrese de que la impresora y el ordenador estn apagdos antes de conectar el cable de datos. La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarlo algn tiempo antes de tocarla. No permita que se realice cualquier operacin o accin de una forma diferente a lo que se seala en el manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. El dispositivo y la toma de corriente deben estar ubicados de forma que sea fcil acceder a ellos. V Tally Dascom 1140
. (Russian)
, , .
,
.
, .
,
.
, .
, .
, ,
. - ,
.
, . ,
. VI Tally Dascom 1140 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora. Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou substncias explosivas. Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. No exponha a impressora a temperaturas altas ou luz solar direta. No aproxime substncias lquidas da impressora. Proteja a impressora de choques, impactos e vibraes. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de toc-la. No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, contate seu revendedor ou companhia de servio. A impressora e a tomada devem ser facilmente em todos os momentos acessveis. VII Tally Dascom 1140 nemli Gvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatle okuyun. Bakm ve tamir almalarn kesinlikle ve hibir surette kendi banza yapmayn; her zaman kalifiyebir uzman servis-teknisyenine haber verin. Yazcy, zerinden yere dmesi mmkn olmayacak sabit ve dz bir zemine yerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veya patlayc maddeler ieren nesnelerin yaknna koymayn. Yazc akm kablosunu sadece doru gerilime sahip bir prize takn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zaman prizden kartn. Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalan meknlarda bulundurun. Yazc hibir sv maddeyle temasta olmamaldr. Yazc hibir sarsntya, darbeye veya titreime mruz kalmamaldr. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapalolduklarndan emin olmalsnz. Yazcnn ba basma esnasnda yksek sya ulayor. Bu yzden ltfen dokunmadan nce ksa sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfen imlatnza veya mteri hizmetleri servisinize bavurun. Cihaz ve elektrik prizinin her zaman kolayca eriilebilir olmas gerekir. VIII Tally Dascom 1140 TRADEMARK ACKNOWLEDGEMENTS IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7,Windows 8, Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008/2013 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom 1140 X Tally Dascom 1140 TABLE OF CONTENTS 1 Unpacking Guide ......................................................................................................................................... 1 1.1 Unpacking the Printer ........................................................................................................................................ 1 1.2 Placing the Printer .............................................................................................................................................. 2 1.3 Printer Components ........................................................................................................................................... 3 2 Setting Up Printer ........................................................................................................................................ 4 2.1 Install Ribbon ...................................................................................................................................................... 4 2.2 Install the Single Sheet Feeder ........................................................................................................................ 5 2.3 Connecting the Interface Cable ........................................................................................................................ 5 2.4 Connecting the Mains Power ............................................................................................................................ 6 2.5 Installing the Windows Driver ........................................................................................................................... 7 3 Paper Installation Guide ........................................................................................................................... 10 3.1 Adjusting the Print Gap Lever ......................................................................................................................... 10 3.2 Friction Feed Handling .................................................................................................................................... 11 3.3 Tractor Feed Handling ..................................................................................................................................... 11 3.4 Continuous Paper Placement ......................................................................................................................... 12 4 Control Panel Operation ........................................................................................................................... 13 4.1 LED Indicators .................................................................................................................................................. 13 4.2 Control Panel Keys .......................................................................................................................................... 14 4.3 Panel Operation ................................................................................................................................................ 15 4.4 Online State ....................................................................................................................................................... 16 4.5 Setup State ........................................................................................................................................................ 17 4.6 Power-On State ................................................................................................................................................ 17 5 Printer Setting Changes ............................................................................................................................ 19 5.1 System Setup .................................................................................................................................................... 19 5.2 Paper Setup ...................................................................................................................................................... 20 5.3 Interface Setup .................................................................................................................................................. 22 5.4 Character Setup ................................................................................................................................................ 22 5.5 Other Setup ....................................................................................................................................................... 23 5.5.1 German (Deutsch)................................................................................................................................... 23 5.5.2 Russian () .................................................................................................................................... 25 5.5.3 Italian (Italiano) ........................................................................................................................................ 26 5.5.4 French (Franais) .................................................................................................................................... 28 5.5.5 Spanish (Espaol) ................................................................................................................................... 30 5.5.6 Turkish (Trkce) ...................................................................................................................................... 31 5.5.7 Portuguese ............................................................................................................................................... 33 5.7 Bidirectional Alignment .................................................................................................................................... 37 5.8 Restore Factory Default................................................................................................................................... 38 6 Customized Form ...................................................................................................................................... 39 6.1 Customize Cut Sheet Form Length ............................................................................................................... 39 6.2 Customize Cut Sheet TOF .............................................................................................................................. 41 6.3 Customize Cut Sheet Bottom Margin ............................................................................................................ 41 I Tally Dascom 1140 6.4 Customize Cut Sheet Left Margin .................................................................................................................. 42 6.5 Customize Fanfold Page Formatting Parameters ....................................................................................... 42 7 Maintenance ............................................................................................................................................... 43 7.1 Cleaning ............................................................................................................................................................. 43 7.2 Cleaning and Vacuuming the Printer ............................................................................................................. 43 7.3 Cleaning the Paper Rollers ............................................................................................................................. 44 8 Troubleshooting ........................................................................................................................................ 45 8.1 Print Quality Problems and Solutions ............................................................................................................ 45 8.2 Paper Handling Problems and Solutions ...................................................................................................... 46 8.3 Operating Problems and Solutions ................................................................................................................ 47 8.4 Printer Failures .................................................................................................................................................. 47 8.5 Error Indications on LEDs ............................................................................................................................... 48 8.6 Diagnostic Functions ........................................................................................................................................ 48 8.7 Firmware Update .............................................................................................................................................. 49 9 General Specifications .............................................................................................................................. 52 10 Interfaces .................................................................................................................................................. 55 10.1 Parallel Interface ............................................................................................................................................ 55 10.2 USB Interface .................................................................................................................................................. 56 11 Character sets & Code Pages ................................................................................................................ 58 11.1 Character Sets ................................................................................................................................................ 58 11.2 Code Page Commands ................................................................................................................................. 63 11.3 Code Page Tables .......................................................................................................................................... 65 12 Control Codes Summary ........................................................................................................................ 89 12.1 Epson Emulation Command List .................................................................................................................. 89 12.2 IBM Emulation Command List ...................................................................................................................... 91 FCC STATEMENT ......................................................................................................................................... 93 II Tally Dascom 1140 Symbols used two symbols. Important information is highlighted in this manual by CAUTION highlights information which must be observed in order to prevent injuries to user and damage to the printer. NOTE highlights general or additional information about a specific topic. III Tally Dascom 1140 1 Unpacking Guide 1.1 Unpacking the Printer 1. Place your packaged printer on a solid base. 2. Make sure that the Up symbols point in the correct direction. 3. Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. 4. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer. The following items should be included:
o Printer o Paper feed knob o Sheet feeder o Power cord o Ribbon cartridge o CD-ROM o Installation Guide Remove the packaging materials from the printer as follows:
1-2. Open and remove the top covers of the printer. 3. Remove the shipping cardboard from around the print head. 4. Install the paper feed knob. 1 Tally Dascom 1140 1.2 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions:
1. Never place the printer near to any flammable gas or explosive substances. 2. Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. 3. When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. 4. Ensure sufficient distance between the printer and any heating devices/radiators. 5. Avoidexposing the printer to extreme temperature or air humidity fluctuations. Avoid exposureto dusty environments. 6. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. 7. The socket-outlet shall be installed near the equipment and shall be easily accessible. 2 Tally Dascom 1140 1.3 Printer Components Component Function Adjusts the print gap lever according to the thickness of paper. Adjusts positioning of single sheet paper. 9-pin printing mechanism Protects print head and other components inside, and reduce noise. Shows printer status, for printer setup. Gap Lever Paper Guides Print Head Cover Control Panel Paper Feed Lever Two positions:
Paper Feed Knob Manual feed or vertical positioning of paper. Power Switch Ribbon Cartridge Ribbon Guide Tractors Power Receptacle Connects power cord to the printer. Interface Power printer ON or OFF Install ribbon in the printer. For guiding ribbon installation on print head. For feeding and adjustment of continuous forms. Connects interface cables from the host.
= continuous forms;
= single sheet paper 3 Tally Dascom 1140 2 Setting Up Printer 2.1 Install Ribbon Switch printer off during ribbon installation. 1. Ensure the power to the printer is off and the print gap lever A is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions - on the ribbon cassette into the printer mounting. 3. Press the ribbon frame onto the print head. 4. Turn the ribbon knob in clockwise direction until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly. 5. Ensure the print gap lever A is set to the original position. 6. Close the printers cover. When printer is in operation, ensure the printers cover is closed to keep the noise level to a minimum. Notes on Ribbon Cartridge Removal:
1. Eject any paper loaded in the printer. 2. Turn off the printer power. 3. Open and remove the cover. 4. Set the gap lever to the most open position labeled RIBBON. 5. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 6. Remove the ribbon frame from the print head. 7. Use fingers to take hold of the handle on the ribbon cartridge firmly, and lift the cartridge upwards to unlatch it. Some force may be needed to unlatch the cartridge. 4 Tally Dascom 1140 2.2 Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. 2.3 Connecting the Interface Cable The 36-pin Centronics parallel and USB ports are located at the rear of the printer. IMPORTANT:
Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports. 5 Tally Dascom 1140 2.4 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your countrys power supply voltage. To do this, check the ratingplate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power swith A, located to the right side of the printer, is in the O(off) position. Connect the power cord to the power inlet of the printer. Connect the power cord plug to a mains socket. Switch on the printer. 6 Tally Dascom 1140 2.5 Installing the Windows Driver
(Windows 2000 / XP / Vista / 7 / 8 / 8.1 and 2003 / 2008 / 2012 / 2012R2 Server) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer DriverSetup.exe. You will see the screen on the right. Click Next to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click Next to continue. 3. Select the desired printer model as shown on the right. Click Next to continue. 7 Tally Dascom 1140 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click Next to continue. 5. Click Finish to start the installation process. 6. If the driver is not yet Microsoft Certified, the message on the right would appear. Click Continue Anyway. (As we continue to expand our product portfolio, not all of our drivers may be certified yet. Please check our websitewww.dascom.com for the latest certified drivers.) 8 Tally Dascom 1140 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right. 9 Tally Dascom 1140 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled. 3.1 Adjusting the Print Gap Lever The print gap lever is on the left side of the printer inside the top cover. Take care to adjust the print gap lever to a suitable position whenever you change the number of copies being printed. Using the wrong print gap may cause print head damage or paper jams. Paper type Single sheet 3-ply 4-ply 5-ply 6-ply 7-ply Change ribbon Weight (g/m2) / ply Thickness (mm) Gap lever position 52~100 40~52 40~52 40~52 40~52 40~52
---
0.06~0.12 0.12~0.14 0.17~0.22 0.23~0.27 0.28~0.33 0.34~0.45 Above 0.58 1P~2P 3P~4P 4P~5P 5P~6P 6P~7P Above 7P 7P There are 2 paper feed modes: friction feed and tractor feed. 10 Tally Dascom 1140 3.2 Friction Feed Handling 1. Raise the single sheet feeder until it locks into its mounting. 2. Move the paper-feed lever forward to 3. Adjust the print gap lever if necessary. 4. Align the left paper guide with the mark on the left of the single sheet feeder. 5. Adjust the right paper guide to the width of the paper used. 6. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with for friction feed mode. the platen. 7. The paper should advance automatically to the print position. The printer is now ready to print in the online state. 3.3 Tractor Feed Handling 1. Move the paper-feed lever backward to 2. Adjust the print gap lever if necessary. 3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the for continuous paper position. left tractor door. In the same way, install the paper on the right tractor. 4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut. Push the right lock lever down to secure the right tractor in place. 5. Press theLoad/Ejectkey to load the paper to the starting print position. The printer is now ready to print in the online state. 11 Tally Dascom 1140 3.4 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm. 12 Tally Dascom 1140 4 Control Panel Operation There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are described below:
4.1 LED Indicators Power/Paper Out LED:
On: Power on Flashing: Paper out Flashing + buzzer: Paper jam Font 1 and Font 2LED:
Flashing together: Indicates continuous paper is at tear-off position; otherwise it indicates the selected font. Online LED:
On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. 13 Tally Dascom 1140 4.2 Control Panel Keys Tear Off Key:
When online, this key will move any loaded continuous paper to the tear-off position. When in setup state, this key is used to select the desired font. LF/FF Key:
Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form
(single sheet mode). Load/Eject Key:
When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper (continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting print position. Online Key:
This key switches the printer between online and offline states. Printing is stopped when the printer is switched to offline state. When printer is switched to online state again, printing will resume. Table 4.1 Font Selection Label Tear Off Draft Draft Condensed Quadrato Quadrato Condensed Courier Courier Condensed OCR B OCR A Table 4.2 Switch S1 S2 S3 S4 L2 State Blink Off Off Off On On On Blink Blink L3 State Blink Off On Blink Off On Blink Off On Label Tear off LF/FF Load/Eject Online 14 Tally Dascom 1140 Table 4.3 LED L1 L2 L3 L4 Function Power/Paper Out Font1 Font2 Online 4.3 Panel Operation There are 3 states of operation: Online, Setup and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form Feed, Load/Eject, Clear Buffer and switch to offline state for accessing to Setup state. In the Setup state, the keys provide font selection, and micro feed paper. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer. This state provides the following functions: Hex-dump, Main Menu setup, print Main Menu, Adjust Factory Defaults, Customize Form, restore factory defaults, and firmware update. The followings describe the 3 states in details. Legend:
[A] = press and hold switch A
{B} = press and then release switch B
[A]+ {B} = press switch B while holding A 15 Tally Dascom 1140 4.4 Online State Switch Operation LED Function Description Function Name Tear Off LF FF
{S1}
{S2}
[S2]
Load/Eject
{S3}
Online Setup State
{S4}
[S4]
Clear Buffer and Reset
[S4]+{S1}
L2, L3 flash This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts on the next TOF by pressing any key or receiving print data from the host.
-
-
-
L4 L4
--
Feeds one line with every press of S2 Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). Load: Automatically loads the paper (according to path selection) when no paper is on the platen. Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE:
Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. Toggles between Online and Offline states. Hold the S4 key for 3 seconds. Toggles to 3s Setup state. Indicated by flashing L4. Clears the print buffer. Beeps once upon completion. Pressing S1 longer initializes the printer to default settings.Beeps 3 times upon completion. 16 Tally Dascom 1140 4.5 Setup State Function Name Switch Operation LED Function Description Toggling to the Online state will cause the printer to go into a ready-to-print state. Any changes made in Setup state will be saved permanently. Lighting up L4 indicates the Online state. Press S3 to micro feed paper up. Press S2 to micro feed paper down. L4
--
--
L2, L3 Refer to Table 4.1 for details. Online state
{S4}
{S3}
{S2}
{S1}
Micro UP Micro Down Font Select 4.6 Power-On State 17 Tally Dascom 1140 Function Name Switch Operation LED Function Description Hex Dump
[S3]
Menu Setup
/ EDS Self Test /
Status Page
[S1]
[S4]
Firmware Update
[S1]+[S2]+[S3]
+ [S4]
-
-
-
L3, L4 Restore Factory Defaults Service Menu
-
[S2] + [S4]
[S1] + [S2]
Customize Form
[S3] + [S4]
-
Beeps once to indicate going into hex dump mode:
Prints data from host in hexadecimal representation. Pressing S4 suspends the printing. When the hex dump has finished, pressing S4 forces the printing of the last line of data, as any line termination control code from host has no function. Switch off the power to terminate the hex dump. Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Prints the printer settings and self-test pattern. Alternate flashing of L3 and L4 indicates ready for firmware update from host. When new firmware is being received: L3 and L4 flash together,while L1 and L2 LEDs are constantly on. When downloading is completed, the carriage returns to home position. Printer initializes normally. Restore all settings to factory defaults. The carriage initializes and the printer beeps once after restoration. Release the keys till the carriage moves to the left side and the beeper beeps twice. Changes of TOF, tear-off position (fanfold only) are not recovered by Restore Factory Defaults. Not recommend the users change the settings by this function. To customize the margins and tear-off position, please refer Chapter 6 for details. 18 Tally Dascom 1140 5 Printer Setting Changes In order to meet specific print requirements, the printer configurations may be changed as follows: Hold down the Load/Eject key while powering on the printer and then release the key when the print head starts to move. The printer will enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off. The Printer Settings menu contains 8 sub-menus: System Setup, Paper Setup, Interface Setup, Charater Setup, Other Setup, Bi-directional Aligment, BlackMark Mode,Restore Facotry Defaults. 5.1 System Setup System setup Valid Settings Function Language English,Deutsch, Pocc, Italiano,Franais,Espaol, Trke, Portuguese Emulation ESC/P2, IBM 2380+
Auto CR
(ESC/P2) No, Yes Auto CR(IBM) No, Yes Auto LF No, Yes Print Dir Bi-Dir, Uni-Dir Zero 0, Graphic Speed Normal, Fast Change Pin#1: No, 1, 2, 3, 4, 5, 6, 7, 8, 9 Change Pin #2 No, 1, 2, 3, 4, 5, 6, 7, 8, 9 Impact Normal, Heavy Allows user to select one of the following languages: English, German, Russian, Italian, French, Spanish and Turkish, Portuguese Selects the printer emulation. This should be the same as the host printer driver. Yes: LF = LF+CR; No: LF = LF
(Applies to ESC/P2 emulation only) Yes: LF = LF+CR; No: LF = LF
(Applies to IBM emulation only) Yes: CR = CR+LF; No: CR = CR Bi-Dir: Graphics and text are printed in both directions, resulting in faster printing speed. Uni-Dir: Graphics and text are printed from left to right, resulting in higher precision. 0: No-slashed Zero 0.
: Slashed Zero . Selects different print quality and print speed for graphic. Defines the first broken / worn out pin. This pin will be substituted by an adjacent pin in the second pass printing. No: Not to substitution of the worn out pin. Defines the first broken / worn out pin. This pin will be substituted by an adjacent pin in the second pass printing. No: Not to substitution of the worn out pin. Normal: The print speed is faster causing head hot easily and the impact force is weaker. Heavy: The print speed is reduced, resulting better thermal performance and copy capability. 19 Tally Dascom 1140 5.2 Paper Setup Paper Setup Valid Settings Function Single FormLen Single Top Single Bottom Single Left Mrg
(1.00mm) Single Top Mrg (0.01) 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define
-7, -6, -5, -4, -3, -2, -1, 0,1, 2, 3, 4, 5, 6, 7 Auto Load Disable, 0.5sec, 1sec, 1.5sec, 2sec Fanfold FormLen Fanfold Top Fanfold Bottom Fanfold Left Mrg
(1.00mm) Fanfold Top Mrg
(0.01) 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Skip No, Yes Sets the page length for single paper Defines the separation in inches from the top edge of a single paper to the first print line. Defines the separation in inches from the bottom edge of a single paper to the last print line. Compensation value added to Single Left Mrg. Compensation value added to Single Top. Defines the settling time before a single sheet is loaded. Disable: Press theLoad/Ejectkey manually to load a single sheet. Sets the Page Length for fanfold. Defines the separation in inches from the top edge of a fanfold to the first print line. Define the separation in inches from the bottom edge of a fanfold to the last print line. Compensation value added to Fanfold Left Mrg. Compensation value added to Fanfold Top. Skips printing on perforation area. Only valid to fanfold. Yes: Blank lines between 2 pages. No: No blank lines between 2 pages. 20 Tally Dascom 1140 Paper Setup Valid Settings Function Tear Auto, Manual, View, Auto @ FF Buzzer No, Yes BlackMark No, Yes Auto: No incoming print data in 1~2 seconds after printing completed, the printer advances the form to the tear-off position. When the printer receives new print data, the form is ejected to the top-of-form. Manual: After the completion of a print job, press a panel key to advance the paper to the tear-off position. View: No incoming print data in 1~2 seconds after printing completed causes the printer to advance the paper by 2 lines. Printing resumes 2 lines below the torn edge. Auto @FF: a formfeed command is necessary to auto feed the form to tear position. No: Buzzer does not sound if out of paper. Yes: Buzzer sounds if out of paper. No: Disables black mark sensor. Yes: Enables black mark sensor. When Yes and online, pressing the Load/Eject key advances the paper to the tear-off position. BlackMark commands: (also see section 5.6) 1D 0C:
Feeds paper to the print position designated by the black mark. Advance the paper to the tear-off position after printing. 1C 28 4C 03 00 42 m:
m = 0: feeds paper to the print position designated by the black mark. m = 1: feeds paper to the black mark tear-off position. Pressure lever Invalid,Standard, Speed The pressure lever presses the paper against the print platen during printing, but it is released for paper loading. Invalid: If you uninstall the lever or want to disable the function, set this setting to invalid. Standard: Release the lever for paper loading and lower the lever to press the paper against the platen during printing. Speed: When the paper is in tear-off position, after the printer received printing data, the printer will judge whether tear-off was implemented first. If tear-off was implemented and printing position is in lever area, then the printer will press the lever; If tear-off was not implemented, the printer will not press the lever. 21 Tally Dascom 1140 5.3 Interface Setup Interface setup Valid Settings Function PnP USB ID No, Yes No, Yes 5.4 Character Setup No: Disables plug and play for USB Yes: Enables plug and play. No: Disbles USB ID. Yes: Enables USB ID Character setup Valid Settings Function Character Table Character Group Int'l Char Set Font Italic, Graphic Group 1, Group 2 USA, France, Germany, UK, DenmarkI, Sweden, Italy, SpainI, Japan, Norway, DenmarkII, Spain II, LatinAm, Denmark, China Draft,DraftCond,Quadrato,Quadr atoCond,Courier,CourierCond,O CR B,OCR A Pitch(cpi) 10, 12, 15, 17, 20, PS CP 437, CP 737, CP 850, CP 851, CP 852, CP 857, CP 858, CP 860, CP 861, CP 863, CP 1252, CP 1253, CP 1254, 8859-
1, 8859-1 (SAP), 8859-2, 8859-
5, 8859-7, 8859-9, 8859-15, Kamenicky , Mazovia, 866 Bulgaria, CP 1250, CP 1251. BRASCII, Abicomp, CP 865, CP 866, CRO-ASCII No, Yes 22 Code Page HS-Draft Italic: Selects standard character sets. Please refer to UG for details. Graphic: Selects IBM character sets. Please refer to UG for details. The interpretation of ASCII codes between 0x80~0x9F:
Group 1: as control codes. Group 1: as printable characters. International character set selections Selects the font. Controls the characters per inch setting. Code page selections On: Prints High Speed Draft when Draft font is selected. Tally Dascom 1140 5.5 Other Setup Other setup Form Length Ctrl Valid Settings No, Yes PrintSpeed Ctrl No, Yes Pitch Ctrl No, Yes Font Ctrl No, Yes Uni-Dir Ctrl No, Yes Function No: Form length commands are invalid in neither of the emulation. Yes: Form length commands are valid in either of the emulations. No: Print speed commands are invalid in neither of the emulation. Yes: Print speed commands are valid in either of the emulations. No: Ignores CPI commands Yes:CPI commands are valid No: Ignores font select commands Yes: font select commands are valid No: Uni-Direction print commands are invalid in neither of the emulation. Yes: Uni-Direction print commands are valid in either of the emulations. 5.5.1 German (Deutsch) System Setup Sprache Emulation Auto CR (ESC/P2) Auto CR (IBM) Auto LF Druck Dir Null Graphikgeschw. Ersetze 1.Nadel Ersetze 2.Nadel Impact Mode Gltige Werte English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
Nein, Ja Nein, Ja Nein ,Ja Bi-Dir, Uni-Dir 0, Normal, Schnell No, 1, 2, 3, 4, 5, 6, 7, 8, 9 No, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normal, Stark 23 Tally Dascom 1140 Papier Setup Einzel Lnge Einzel Ob Rand Einzel Unt Rand Einzel Li Rand Einzel Ob Rand Fein Auto Laden Endlos Form Lnge Endlos Ob Rand Endlos Unt Rand Endlo Li Rand Endlos Ob Rand Fein Perforationssprung Abreissen Summer Black Mark Pressure lever Gltige Werte 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definiert 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Ungltig, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definiert 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Nein ,Ja Auto, Manuell, Kurz,Auto@FF Nein ,Ja Nein ,Ja Invalid, Standard,Speed Schnittstellen Setup Gltige Werte PnP USB ID Zeicheneinstellung Zeichentabelle PC-Zeichensatz Land Font Laufweite(cpi) Zeichensatz HS-Draft Nein ,Ja Nein ,Ja Gltige Werte Italic, Graphik Gruppe 1, Gruppe 2 USA, Frankreich, Deutschland, UK, Dnemark I, Schweden, Italien, Spanien I, Japan, Norway, Dnemark II, Spanien II, Lat-
Amerika, Dnemark/Norwegen, China Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCond,OC R B,OCR A 10, 12, 15, 17, 20, PS CP 437,CP 737 Nein, Ja 24 Tally Dascom 1140 Formularlnge Strg Geschwindigkeit Strg Laufweite Strg Font Strg Uni-dir Strg 5.5.2 Russian () CR( ESC/P2) CR (IBM) LF e ea o a1. a 2
. o. . a y
.. a y epep
. ep Pressure lever Nein, Ja Nein, Ja Nein, Ja Nein, Ja Nein,Ja Valid Settings English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
,,
,,
,
, 0, Hopao, No, 1, 2, 3, 4, 5, 6, 7, 8, 9 No, 1, 2, 3, 4, 5, 6, 7, 8, 9 a, Valid Settings 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1,
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7,
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1,
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7,
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
,
, , ,Auto@FF
,
, Invalid,Standard,Speed 25 Tally Dascom 1140 PnP USB ID Font
/ (cpi) a
,
, Valid Settings Valid Settings
, I, II USA, France, Germany, UK, -I, Sweden, Italy, Spain-I, Japan, , II, Spain II, ,
/, Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCond, OCR B,OCR A 10, 12, 15, 17, 20, PS CP437, CP737
, Valid Settings a yp Ctrl ,
, Ctrl
, a Ctrl
, p Ctrl Ctrl , 5.5.3 Italian (Italiano) Setup sistema Impostazioni Valide Linguaggio Emulazione Auto CR (ESC/P2) Auto CR (IBM) Auto LF Direz.Stampa Zero Veloc. Grafica Primo ago rotto Secondo ago rotto Modo Impatto English,Deutsch,Pocc,Italiano,Franais,Espaol,Trke, Portuguese ESC/P2, IBM 2380+
No, Si No, Si No,Si Bi-Dir, Uni-Dir 0, Normale, Veloce No, 1, 2, 3, 4, 5, 6, 7, 8, 9 No, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normale, Pesante 26 Tally Dascom 1140 Imposta carta Lunghezza Foglio Margine Sup. Foglio Margine Infer. Foglio Regola foglio a SX Regola Sup.Foglio Autocaricamento Lungh. Mod. Continuo Margine Superiore Mar. Inf. Continuo Regola a SX continuo Regola Sup.continuo Salto Perforazione Strappo Cicalino Segno nero riferim Pressure lever Setup IF PnP ID USB Imposta caratteri Tabella Caratteri Gruppo Carattere Set Carat. Int. Font Spaziatura(cpi) Code Page Impostazioni Valide 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definito 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Non valid, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definito 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 No,Si Auto STP, STP manuale, STP corto,Auto@FF No, Si No,Si Invalid,Standard,Speed Impostazioni Valide No, Si No,Si Impostazioni Valide Italico, Grafica Groupo 1, Groupo 2 USA,Francia, Germania, Regno Unito, Danimarca I, Svezia, Italia, Spagna I, Giappone, Norvegia, Danimarca II, Spagna II, Sudamerica, Danimarca/Norvegia, Porcellana Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCond, OCR B,OCR A 10, 12, 15,17, 20,PS CP437, CP737 27 Tally Dascom 1140 HS-Bozza Altri Setup Comando lunghezza Comando velocit Comando Spaziatura Comando Fonte Comando stampa mono 5.5.4 French (Franais) Setup Systme Language Emulation RC-Auto (ESC/P2) RC-Auto (IBM) SL-Auto Dir Impr Zro Vitesse graphiq. Changer aiguille 1 Changer aiguille 2 Mode Impact Rglage papier Feuille LongPage Bord Sup.Feuille Bord Inf.Feuille Marge Gauche Feuille Marge Haute Feuille Chargem. Autom Listing Longpage No, Si No, Si No, Si No, Si No, Si No,Si Impostazioni Valide Paramtres Valides English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
Non, Oui Non, Oui Non,Oui Bidir, Unidir 0, Normal, Rapide Non, 1, 2, 3, 4, 5, 6, 7, 8, 9 Non, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normal, Fort Paramtres Valides 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Dfinie 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Dfinie 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Dfinie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Dfinie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Non, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Dfinie 28 Tally Dascom 1140 Listing Bord Sup. Listing Bord infr Listing Marge Gauche Listing Marge Haute Saut perforation Rglage papier Coupe Alarma Mode Repre Noir Pressure lever 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Dfinie 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Dfinie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Dfinie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Non,Oui, Paramtres Valides Auto,Manuelle,Courte,Auto@FF Non, Oui Non,Oui Invalid,Standard,Speed Config Interface Paramtres Valides PnP USB ID Parametrage cartere Table caractere Groupe Caractres Pays Font Espacement(cpi) Code Page HS-Draft Autre rglage Ctrl LongPage Ctrl Vitesse Impr. Ctrl Espacement Ctrl Fonte Ctrl Impr. Uni-Dir Non, Oui Non ,Oui Valid Settings Italique, Graphique Groupe 1, Groupe 2 USA, France, Allemagne, Royaume-Uni, Denmark I, Sude, Italie, Espagne, Japon, Norvge, Denmark II, Espagne II, Ameriquelat, Denmark/Norvge, Chine Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCond,O CR B,OCR A 10, 12, 15, 17, 20, PS CP437, CP737 Non, Oui Paramtres Valides Non, Oui Non, Oui Non, Oui Non, Oui Non ,Oui 29 Tally Dascom 1140 5.5.5 Spanish (Espaol) Ajustes Sistema Lenguage Emulacin Auto CR (ESC/P2) Auto CR (IBM) Auto LF ModoImpresin Cero con barra Imp.Grafica Sust.1er pin roto Sust.2do pin roto Modo de Impacto Config. Papel Tam. Hojas Sueltas Margen Sup. Hoja S. Margen Inf. Hoja S Marg. Izq. Hoja S. Marg. Sup. Hoja S. Auto Carga Tam.Papel Continuo Ajustes validos English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
No, Si No, Si No,Si Bi-Dir, Uni-Dir 0, Normal, Rpido Non, 1, 2, 3, 4, 5, 6, 7, 8, 9 Non, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normal, Fuerte Ajustes validos 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Invlido, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido Mar.Sup. Pap. Con Mar. Inf. Pap.Cont. Marg. Iz. Pap. Cont. Marg. Sup. Pap. Cont. -7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Salto perforacin Corte No,Si Automtico, Manual, Corto,Auto@FF 30 Tally Dascom 1140 Alarma Modo Marca Negra Pressure lever No, Si No,Si Invalid,Standard,speed Conf. Interface Ajustes validos PnP ID USB Men Carcter Tabla de Caracteres Grupo de Caracteres Juego Carcter Int. Tamao Letra(cpi) Font Tabla Carcter Alta Velocidad No, Si No,Si Ajustes validos Italic, Grafica Grupo 1, Grupo 2 USA, Francia, Alemania, Reino Unido, Dinamarca I, Suecia, Italia, Espaa, Japn, Noruega, Dinamarca II, Espaa II, AmricaLat, Dinamarca, China 10, 12, 15, 17, 20, PS Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCon d,OCR B,OCR A CP437, CP737 No, Si Config. Otros Ajustes validos Cmd. Long. de Hoja Cmd. Vel. Impresin Cmd. Tamao Letra Cmd.Fuente Cmd. Imp. Uni-dir 5.5.6 Turkish (Trkce) Sistem Ayari Lisan No, Si No, Si No, Si No, Si No,Si Valid Settings English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
Emlation Otom. Satrba (ESC/P2) Hayr, Evet Hayr, Evet Otom. Satrba (IBM) Hayr,Evet Otom. Satr besleme ki-Yne Tek-Yne Yazdrma yn 0, Sfr Says Normal, Hz Grafik Hz 31 Tally Dascom 1140 Arzal 1. ine yed Arzal 2. ine yed Vuru modu Kat Ayar Tek kat uzunluu Tek-kat st boluu Tek-kat Altkenar Tek-kat Sol ayar Tek-kat st ayar Otom. Ykleme Srekli Kat Uzunluu Srekli st Marj Sr. Form Kt Alt Sr Form Kt Sol Sr Form Kt st Delik atlama Kat Kesme ikaz Siyah izgi alg Pressure lever Arabirim Ayar PnP USB ID Karakter ayar Karakter tablosu Karakter Grubu Karakter setleri Font Hayr, 1, 2, 3, 4, 5, 6, 7, 8, 9 Hayr, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normal, Gl Geerli ller 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Oto.Tanm. 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto.Tanm. 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto.Tanm.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Oto.Tanm.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Geersiz, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Oto.Tanm. 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto.Tanm. 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto.Tanm.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Oto.Tanm.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Hayr, Evet Oto.kesim,Elle kesim ,kisa kesim, Auto@FF Hayr, Evet Hayr, Evet Invalid,Standard,Speed Geerli ller Hayr, Evet Hayr,Evet Geerli ller talik, Grafik Grup 1, Grup 2 Amerika, Fransa, Almanya, ngiltere, Danimarka I, sve, talya, spanya, Japonya, Norve, Danimarka II, spanya II, Ltn Amerika, Danimarka, in Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCon 32 Tally Dascom 1140 Karakter Skl (cpi) Kod Sayfas Yk.Hz-Taslak Dier Ayarlar Kt Uzunluk Komutu Bask Hz Komutu Karak.Aralk Kont. YazTipi Komutu Tek yn bask Komutu 5.5.7 Portuguese Config. Sistema Linguagem Emulao Auto CR(ESC/P2) Auto CR(IBM) Auto LF Direo Imp. Zero Imp.Grafica Substituio Pino 1 Substituio Pino 2 Modo de Impacto Config. Papel Tam.Folha Solta Margem Topo Folha Margem Inf. Folha Margem Esq.Folha d,OCR B,OCR A 10, 12, 15, 17, 20, PS CP437, CP737.. Hayr, Evet Geerli ller Hayr, Evet Hayr ,Evet Hayr ,Evet Hayr ,Evet Hayr,Evet Valid Settings English,Deutsch,Pocc,Italiano,Franais,Espaol, Trke,Portuguese ESC/P2, IBM 2380+
No, Sim No, Sim No, Sim Bi-Dir, Uni-Dir 0, Normal,Rpido No, 1, 2, 3, 4, 5, 6, 7, 8, 9 No, 1, 2, 3, 4, 5, 6, 7, 8, 9 Normal, Forte Valid Settings 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido 33 Tally Dascom 1140 Margem Dir.Folha Carreg.Auto Tam.Form.Cont. Mar.Topo Form.Cont. Mar.Inf. Form.Cont. Mar.Esq. Form.Cont. Marg.Topo Form.Cont. Salte perfurao Corte Cigarra Modo Marca Preta Pressure lever Confi.Interface PnP ID USB Config. Carter Tabela de carateres Grupo de carateres Conj.carateres Int. Font Passo(cpi) Pgina de Cdigo Alta Velocidad Config. Outros Cmd.Tam.de Folha Cmd.Vel.Impresso Cmd.Passo Cmd.Fonte Cmd.Imp.Uni-dir
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Desativo, 0.5sec, 1sec, 1.5sec, 2sec 2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido 0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 No, Sim Automtico, Manual, Curto,Auto@FF No, Sim No, Sim Invalid,Standard,Speed Valid Settings No, Sim No, Sim Valid Settings Italic, Graphic Group 1, Group 2 EUA, Frana, Alemanha, Reino Unido, Dinamarca, Sucia, Itlia, Espanha, Japo, Noruega, Dinamarca II, Espanha II, Amrica Lat, Dinamarca, China Draft,DraftCond,Quadrato,QuadratoCond,Courier,CourierCon d,OCR B,OCR A 10, 12, 15, 17, 20, PS CP437, CP737.. No, Sim Valid Settings No, Sim No, Sim No, Sim No, Sim No, Sim 34 Tally Dascom 1140 5.6 Black Mark Parameters This printer uses tractors to load fanfold forms with pre-printed black marks. The printer requires 3 parameters to print on paper with black marks:
1. Horizontal offset of black mark from the edge of page (called Black Mark Physical Horizontal Position); later on, this value facilitates the printer to locate its scanner preparing for identifying the black marks. 2. Vertical offset of the first print line from the black mark (called Distance Offset From Black Mark To Print Position); later on, the print makes use of this value to print the first line relative to the black mark. 3. Vertical offset of the tear-off edge from the black mark (called Distance Offset From Black Mark To Tear Position); this value informs the printer the tear-off position of the page. Not to skip or change the order of setting the above 3 parameters. The procedures to set the parameters:
1. Hold down the Tear key while powering on the printer and then release the key when the print head starts to move. After loading paper, the printer prompts the Printer Settings Printer Settings
[TEAR]=Back, [LF]=Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer. System Setup 2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer shows:
BlackMark Mode 3. Press OK to go into the BlackMark menu. The printer prompts:
[Black Mark Adjustment Mode]
[TEAR]= Back, [LF]= Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]= Save and restart the printer. Black Mark Physical Horizontal Position Press any key to eject the paper, and load paper with black mark in the Fanfold Path. 4. The last prompt above advises you to press any key to unload the dialog form. Then load a fanfold form with black mark. 35 Tally Dascom 1140 5. Ensure to place the lever at position. Then press the Load/Eject key to load the black marked form. The top edge of the form will then align with the printers tear-off blade. Press Next or Back until you see the black mark marginally exposed out of the tear-off blade. Then press OK to allow the printer to scan the horizontal offset of the black mark relative to the left edge of the page. (Meanwhile, the vertical position of the black mark is measured and recorded.) When the printer fails to scan the horizontal offset, it prompts you to repeat the above procedures. If scanning is successful, it prompts:
Successfully setup black mark parameters. Distance Offset From Black Mark To Print Position 6. The last prompt above invites you to set the next parameter --- vertical offset of the first print line from the black mark. Like other setting dialogs, you have options:
1) to bypass this setting (by pressing Next or Back), (WARNING: Not to skip or change the order in Black Mark Setting.) 2) to accept the invitation (by pressing OK), 3) to leave the subsequent settings (by press Exit), or 4) to terminate the session and save modified parameter(s) (by pressing Save and Restart). 7. When you respond with OK to set the vertical offset, the printer prompts you to reload a black marked fanfold form:
Press any key to eject the paper, and load paper with black mark in the Fanfold Path. The top edge of the form will then align with the printers tear-off blade. Press Next or Back to feed or reverse-feed the paper till the desired first print line position is reached.
(With the above measured vertical position, the printer will convert the net paper feeding to the TOF relative to the black mark.) Press OK to confirm the vertical offset. Then the print prompts the invitation for setting the tear-off position relative to the black mark:
Successfully setup black mark parameters. Distance Offset From Black Mark To Tear Position 8. When you respond with OK to set the tear-off position, the printer prompts you to reload a black marked fanfold form:
Press any key to eject the paper,and load paper with black mark in the Fanfold Path. The printer reloads the form. By default the form stops 5.5 inches away from the printers tear-off blade. Press Next or Back to feed or reverse-feed the paper till the desired tear-off position is reached. (With the above measured vertical position, the printer will convert the net paper feeding to the tear-off position relative to the black mark.) Press OK to confirm the tear-off offset relative to the black mark. Finally, press Save and Restart to save new settings and terminate the session. 36 Tally Dascom 1140 5.7 Bidirectional Alignment When wiggling vertical grids appears in tabular reports, you should adjust the Bidirectional Alignment. The procedures to adjust bi-directional alignment across adjacent line grids:
1. Hold down the Tear key while powering on the printer and then release the key when the print head starts to move. After loading paper, the printer prompts the Printer Settings. Printer Settings
[TEAR]=Back, [LF]=Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer. System Setup shows:
Bi-directional Alignment 2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer 3. Press OK to go into the Bi-directional Test menu. The printer prompts:
[Bi-direction Alignment]
[TEAR]=-1, [LF]=+1, [LOAD/EJECT]=OK, [ONLINE]=Back,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer 50
| | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |
4. Every press on +1 or -1 shifts the second line to the right or left, respectively, relative to the top line by 1 fine step. After pressing +1 twice and then OK, the printer prompts:
52
| | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |
5. Repeat the adjustment till two grid lines align satisfactory as |. Press OK again. The printer asks if you want to save the correction:
Save the parameter settings ([LOAD/EJECT] or [ONLINE] = OK, [LF] = Next)?
Yes At this stage, you have the options to save or give up the correction by pressing OK or Next, respectively. If you respond with OK, an asterisk * appends to Yes to confirm saving change.If you intend to give up the correction by pressing Next, the printer prompts a No Then a confirmative response of OK appends an asterisk * to the No prompt. The printer then exits the Bi-directional Test and proceeds with the next setup menu. 37 Tally Dascom 1140 5.8 Restore Factory Default The procedures to restore factory default settings:
1. Hold down the Tear key while powering on the printer and then release the key when the print head starts to move. After loading paper, the printer prompts the Printer Settings Printer Settings
[TEAR]=Back, [LF]=Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer. System Setup 2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer shows:
Restore Factory Defaults 3. Press OK to go into restore factory default dialog. The printer prompts:
[Restore Factory Defaults]
Restore factory settings ([LOAD/EJECT]=OK, [ONLINE]=Exit)?
Yes 4. At this stage you have the option of OK to restore default setting or Exit to discard the 5. If input OK, the printer prints an asterisk * appending the Yes and prompts restoration. successful restoration:
Restore factory settings successfully 6. The printer beeps once to indicate successful restoration. 38 Tally Dascom 1140 6 Customized Form This printer allows the customization on the form length, Load/Eject, bottom margin and left margin for single sheets and fanfold. Restore Factory Defaults can recover these default values. Selecting the Define value(s) in section 5.2 (Paper Setup menu) allows the printer to take up the customized page formatting value(s). The parameter setting procedures involve:
1. The printer prompts the dialogs and you follow the prompts. 2. Before every measurement or change, the print instructs you to unload the conversation form from the printer. 3. With the exception of measuring the form length for cut sheets, always set the lever to the tractors position
. 4. For form length measurement, insert the customized form from the proper paper path. The other six settings are actually done on general fanfold forms --- not the actual customized form. Fanfold paper gives direct visual results on the TOF, bottom and left margins even though cut sheets will be used in actual applicati 6.1 Customize Cut Sheet Form Length 1. Hold down both the Online and TOF keys while powering on the printer and then release the keys when the carriage initializes and beeps once. After loading a form the printer prompts:
Customize Form
[TEAR]=Back, [LF]=Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer. Single sheet 2. Press OK to start customizing all or part of 4 parameters for single sheet. The printer prompts:
[Single sheet]
Form Length 39 Tally Dascom 1140 3. You may skip to other customized settings by pressing Next or Back. Once you press OK to continue with form length measurement, the printer prompts:
1.Press any key to clear the Setup Instructions Page from the printer. Insert the Customized Page into the corresponding paper path. Press [LOAD/EJECT] to load and measure the page length. 2.The printer rolls over the entire Customized Page to measure its length. After measurement, press [LOAD/EJECT] to load a blank Setup Instructions Page to report the measured value. 3. Press [LOAD/EJECT] to save the measured value.Repeat the above steps if the printed value is dissatisfactory. illustrations for above step 1 and step 2. 4. Follow the given prompt to unload the conversation form. Load the customized form to allow the printer to scan the page length. After the measurement, load another conversation form to let the printer print out the measured length. The measured form length is: 11.0Inch, approximately equal to 279mm, accuracy of plus or minus 0.1 inches. The measured value has been saved. Remeasure ( [LOAD/EJECT]=OK, [ONLINE] =Exit)?
Yes 40 Tally Dascom 1140 5. At this stage:
If Load/Eject is pressed, an asterisk * is appended to Yes and you should repeat the procedures for form length measurement as mentioned. Or, If you input Exit, the printer saves the measurement value and proceeds with the next customized setting. 6.2 Customize Cut Sheet TOF 1. After you follow through all the steps in 6.1 or you input Next in step 3 in 6.1, the printer prompts:
Top Margin 2. You may skip to other customized settings by pressing Next or Back. Once you press OK to continue with customization of cut sheet TOF, the printer prompts:
Press any key to eject current page, load paper in the Fanfold paper path, and then proceed as follows:
[TEAR] = -(1/72) inch, [LF] = +(1/72) inch, [LOAD/EJECT] = OK, [ONLINE] = Exit,
[ONLINE] + [LOAD/EJECT] = Save and restart the printer. 3. Follow the given prompt to unload the conversation form. Ensure the lever is at position. Then press the Load/Eject key to load fanfold paper from tractors. The top edge of the form initially aligns with the printers tear-off blade. You may input +/- 1/72 to adjust the TOF position. When you get the desirable TOF, press OK or Exit. The printer prompts the customized TOF value:
The defined position is: 4.2 mm. Save the parameter settings ([LOAD/EJECT] or [ONLINE]=OK, [LF]=Next)?
Yes 4. At this stage:
If Load/Eject is pressed, an asterisk * is appended to Yes and you should repeat the procedures for form length measurement as mentioned. Or, If you input Exit, the printer saves the measurement value and proceeds with the next customized setting. 6.3 Customize Cut Sheet Bottom Margin 1. After you follow through all the steps in 6.2 or you input Next twice in step 3 in 6.1, the printer prompts:
Bottom Margin 2. The remaining operations are nearly the same as described in section 6.2. The only difference is to input +/- 1/72 till you get the desirable bottom margin. 41 Tally Dascom 1140 6.4 Customize Cut Sheet Left Margin 1. After you follow through all the steps in 6.3 or you input Next three times in step 3 in 6.1, the printer prompts:
Left Margin 2. The remaining operations are nearly the same as described in section 6.2. The only difference is to input +/- 1/72 till you get the desirable left margin. 6.5 Customize Fanfold Page Formatting Parameters The customizations of the form length, TOF, bottom and left margins for fanfold are exactly the same as describe. All you need is to bypass the Single Sheet menu under Customize Form. Follow step 1 in section 6.1:
Customize Form
[[TEAR]=Back, [LF]=Next, [LOAD/EJECT]=OK, [ONLINE]=Exit,
[ONLINE]+[LOAD/EJECT]=Save and restart the printer. Single sheet Then hit Next instead to get into the fanfold parameter menus:
[Tractor Paper]
Form Length Refer section 6.1 to 6.4 for details on customizing the form length, TOF, bottom margin, and left margin for fanfold. 42 Tally Dascom 1140 7 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer to determine whether lubrication may be necessary. Switch printer off and unplug the power cord from the main before doing any maintenance work. 7.1 Cleaning The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover is open. 7.2 Cleaning and Vacuuming the Printer If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the printer, clean the printer. To clean and vacuum the printer:
1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer power cord. 2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge. 3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer. 4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends from the print head carriage. 5. Re-install the ribbon cartridge. 6. Remove the single sheet feeder and clean the form tractors and the surrounding areas. 7. Re-install the single sheet feeder. 43 Tally Dascom 1140 7.3 Cleaning the Paper Rollers Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to harden. To clean the rollers and the platen:
1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer. 2. Place the cloth against the platen and manually rotate the paper feed knob. 3. Repeat this procedure for each roller. 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob. 44 Tally Dascom 1140 8 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. 8.1 Print Quality Problems and Solutions Problem Solution Printing is too light or too dark. Smears and stains appear on the page. Printing is erratic or the wrong characters are printed. Many
? or unexpected characters are printed. The page is blank. Printing is vertically misaligned (jagged). The top margin is wrong. Lines are double spaced instead of single spaced. The printer overprints on the same line. The next print line starts where the previous line ended instead of at the left margin. Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly. Replace the ribbon if necessary. Make sure that the print gap lever is set for the thickness of your paper. Make sure that the print gap lever is set for the thickness of your paper. Check for ribbon wear. Replace the ribbon if necessary. Check whether the tip of the print head is dirty. Clean the head with a soft cloth if necessary. The print head may need to be replaced. Make sure that the interface cable is securely connected to both the printer and computer. Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. Check the length of the interface cable. (Maximum Parallel & USB: 2 meters, Serial: 15 meters) Try another interface cable. Make sure that the ribbon cartridge is properly installed. Make sure the gap lever is set correctly. Use the printer's vertical alignment function to check the vertical print alignment. If necessary, adjust the print alignment Check the application top margin setting. Adjust the Top Margin setting in Page Setup menu if necessary. Change the Auto LF setting in the System Setup menu to No. Change the Auto CR setting in the System Setup menu to No. Change the Auto CR setting in the System Setup menu to Yes. 45 Tally Dascom 1140 8.2 Paper Handling Problems and Solutions Problem Solution Paper cannot be loaded or fed. Paper jams while loading. Make sure that the paper select lever located on the top right of the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. Make sure that the paper covers the paper-out sensor. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Make sure that the Print Gap lever is set for the thickness of your paper. Make sure that the paper is not folded, creased, or torn. Make sure that the left and right tractors are set so that the continuous forms are stretched taut. Paper jams while printing. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Make sure that the Print Gap lever is set for the thickness of your paper. For continuous forms, make sure that the incoming and outgoing paper stacks are correctly placed. Paper should feed straight. Make sure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor pins. 46 Tally Dascom 1140 8.3 Operating Problems and Solutions Problem The power does not turn on. The printer is on but it will not print. Paper select lever error Solution Check whether the mains voltage is correct. Make sure that the power cord is securely connected to both the printer and the mains power outlet. Make sure that the power outlet is functional. If not so, use other outlet. Turn the power off. Wait a minute and then turn the printer on again. If the printer still has no power, contact your dealer. Make sure that the Online indicator is lit. If you use the interface cable, make sure it is securely connected to both the printer and the computer. Make sure paper is loaded. Run the printer Status Page. If printing executes normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings. Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position. 8.4 Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner. 47 Tally Dascom 1140 8.5 Error Indications on LEDs Error Description Power LED Font1 LED Font2 LED Online LED Buzzer Sound Off Off Off Off None On Off Flashing Flashing Flashing Flashing Flashing Flashing Flashing Flashing Continuous Continuous Once Once Flashing Flashing No change No change No change No change No change No change No change No change Printhead too hot Paper path switching trouble Paper jam Paper End Carriage initial position Raster reading trouble Paper sensor failure Paper width trouble Print head thermal sensor failure 8.6 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer No change No change No change No change Continuous Flashing Flashing Flashing Once None None Off Off Off Off Off hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer. HEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps. PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printers vertical line print alignment in bi-directional mode. For details on using these functions, please refer to chapters 4 and 5. 48 Tally Dascom 1140 8.7 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before updating firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person. To load new firmware, proceed as follows:
1. Switch off the printer. Connect your PC to the USB port on the printer. 2. Link Configuration Tool and then click Firmware Update as shown in below picture:
3. Click Browse to choose program file and character set, then Click Start ,following message is prompted. Click OK. 49 Tally Dascom 1140 4. Enter download process and it is shown as below picture. In this process, L1 and L2 are on; And L3 and L4 are blinking. 50 Tally Dascom 1140 5. When download is completed, the carriage returns to home position. Printer initializes normally. 51 Tally Dascom 1140 9 General Specifications Printing method Printing direction Print Speed Font Matrix Print Head Serial impact dot matrix Bi-Directional logic seeking character, graphics Bi-Directional or Uni-Directional selection Pitch 10 CPI 12 CPI 15 CPI NLQ 75/240H 90/240H 75/360H Draft 300/120H 360/120H
---
HS Draft(CPS/DPI) 400/90H
---
---
Pitch 10 CPI 12 CPI 15 CPI NLQ Draft 24H*18V/240 12H*9V/120 9H*9V/90 20H*18V/240 10H*9V/120 ---
24H*18V/360 --- ---
HS Draft(Matrix/DPI) Number of pins:
Pin diameter:
Life:
9 pins 0.3 mm 300 million strokes/pin @ Draft mode Graphics Paper Feed Speed Continuous feed: 4.0 IPS (inches per second) Resolution 8-bit mode: 8V x 60H, 72H,80H, 90H, 120H, 144H,240H (DPI) 240x 144 DPI maximum Characters per line (CPL) 10 CPI:
80 CPL 12 CPI:
96 CPL 15 CPI:
120 CPL 17.1 CPI: 136 CPL 160 CPL 20 CPI:
Bitmap Fonts:
1. EAN-13 2. EAN-8 3. Interleaved 2 of 5 4. UPC-A 5. UPC-E 6. Code 39 7. Code 128 8. POSTNET 52 Printable Columns Built-In Fonts Barcodes 1.Draft 10, 12, 15, 17.1CPI, 2. Quadrato 10, 12, 15, 17.1, 20CPI,Proportional 3. Courier 10, 12, 15, 17.1, 20CPI, Proportional 4. HS-draft 10CPI 5. OCR-A 6. OCR-B Tally Dascom 1140 Code Pages International Character Sets Line Spacing Paper Specifications CP 437, CP 737, CP 850, CP 851, CP 852, CP 857, CP 858, CP 860, CP 861, CP 863, CP 1252, CP 1253, CP 1254, 8859-1, 8859-1 (SAP), 8859-2, 8859-5, 8859-7, 8859-9, 8859-15, Kamenicky , Mazovia, 866 Bulgaria, CP 1250, CP 1251, BRASCII, Abicomp, CP 865, CP 866, CRO-ASCII USA, France, Germany, UK, Denmark I, Sweden, Italy, Spain I, Japan, Norway, Denmark II, Spain II, Latin America, Danmark/ Norway, China 1/6", 1/8", n/72", n/216"
Cut Sheet Width:95mm~267mm
(3.75"~10.5") Length:114.3mm~363.2mm
(4.5"~14.3") Weight: 52~100g/
Thickness:
0.065~0.14mm
(0.0026"~0.0055) Weight: 52~100 g/
Thickness:
0.065~0.14mm
(0.0026"~0.0055") Multi-part Fanfold Paper Single ply Width: 95mm~267mm (3.75"~10.5") Length: 114.3mm~558.8mm (4.5"~22.0) Weight: 40~56g/
Thickness: 0.52 mm max
(0.0204 max) Paper Handling Feeding method: Friction/Push tractor/Roll paper Paper path: Cut sheets: Rear in and top out Fanfold: Rear in and top out Copy Capability Original + 3 copies Emulation ESC/P2, IBM 2380+
Ribbon Type Cartridge; Monochrome Ribbon Life 10 million characters (rolling Draft 10 CPI) Input Data Buffer Up to 256KB Windows Drivers Interface Windows Server 2000/2003/2008 Windows Vista Windows XP Windows 98 Windows 7 Windows 8.1 Server 2012 Standard: USB Options: Parallel, Ethernet, WiFi(IEEE802.11 b, IEEE802.11 g, IEEE802.11 n), Blue-tooth 30 EDR Compliant, and serial Operation Panel Switches: 4 pcs LED indicators: 4 pcs 53 Tally Dascom 1140 Noise Level less than 55 dB Ambient Conditions Dimensions Weight Power Supply Power consumption MTTR MTBF Certification Temperature Operating : +5 to +35 C Stand-by : -20 to + 55C Humidity Operating : 10 to 80% RH ( No condensation) Stand-by : 5 to 85% RH 369 mm (width) 283.3 mm (depth) 130 mm (height) approx. 5.5 kg Unit type : Switching mode power supply Power cord : Detachable Voltage rating : AC 120V~230V, 50Hz to 60Hz Stand by : Less than1.3W 34 W (Test pattern is specified in standard ISO/IEC 10561.)
< 20 minutes 10 mil lines (Except print head), Mean time between failure: 10,000 CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV, Microsoft Certified for Windows 7, Windows 8.1,Server 2012 54 Tally Dascom 1140 10 Interfaces 10.1 Parallel Interface Parallel Interface Pin Assignment Signal Name STROBE DATA ACK BUSY PE SELECT AFXT Unused GND F-GND
+5V GND INIT FAULT GND Unused FUSE SLCTIN Signal Transmission Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Unused Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Printer Computer Unused Printer Computer Printer Computer Pin 1 2~9 10 11 12 13 14 15 16 17 18 19~30 31 32 33 34 35 36 Parallel Interface Connector Diagram Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation. 55 Tally Dascom 1140 10.2 USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the B type USB connector. 10.3Serial interface Serial interface pin assignment Pin 1 2 3 4 5 6 7 8 9 Signal name Description RXD TXD DTR SGND DSR RTS CTS Receive data Send data Data terminal ready Signal ground Data set ready Request to send Clear to send Serial interface connector diagram Serial interface wiring diagram 56 Tally Dascom 1140 Note:
1. The serial cable length should not exceed 15 meters. 2. Make sure the Interface Setup selects serial interface and the settings are the same as PC communication port settings. Shown as below:
57 Tally Dascom 1140 11 Character sets & Code Pages 11.1 Character Sets Standard character set 1 Standard character set 2 58 Tally Dascom 1140 IBM character set 1 IBM character set 2 59 Tally Dascom 1140 OCR-A character set 1 OCR-A character set 2 60 Tally Dascom 1140 OCR-B character set 1 OCR-B character set 2 61 Tally Dascom 1140 International Character Set Commands Country USA FRANCE GERMANY UK DENMARK 1 SWEDEN ITALY SPAIN 1 JAPAN NORWAY DENMARK 2 SPAIN 2 LATINAMERICA DENMARK/NORWAY CHINA International character sets Basic Command
<ESC>RCHR(0)
<ESC>RCHR(1)
<ESC>RCHR(2)
<ESC>RCHR(3)
<ESC>RCHR(4)
<ESC>RCHR(5)
<ESC>RCHR(6)
<ESC>RCHR(7)
<ESC>RCHR(8)
<ESC>RCHR(9)
<ESC>RCHR(10)
<ESC>RCHR(11)
<ESC>RCHR(12)
<ESC>RCHR(13)
<ESC>RCHR(16) 62 Tally Dascom 1140 11.2 Code Page Commands Code Page CRO-ASCII Arabic Farsi Arabic Urdu Greek DEC Greek ELOT 928 CP437 Latin US CP737 Greek CP850 Latin 1 CP851 Greek CP852 Latin 2 CP857 Turkish CP858 (IBM with ) CP860 Portugal CP861 Icelandic CP863 French Canada CP864 Arabic CP864 Arab. Extended CP865 Nordic CP866 Cyrillic CP866 Bulgaria Siemens Turkish DEC Turkish CP1250 Win Latin 2 CP1251 Win Cyrillic CP1252 Win Latin 1 CP1253 Win Greek CP1254 Win Turkish 8859-1 Latin 1 8859-1 Latin 1 (SAP) 8859-2 Latin 2 8859-5 Cyrillic 8859-7 Greek 63 ESC R Parameter 3C 96 97 46 6C 80 93 82 88 87 8D 9E 84 94 85 8C 95 86 8E 9D 9B 9C 70 71 72 73 74 25 2B 26 2A 2D Tally Dascom 1140 Code Page 8859-9 Turkish 8859-15 Latin 9 (Euro) BRASCII Abicomp Roman 8 Coax/Twinax(Hebrew) New-437 (Hebrew) New-DIG 850 (Hebr.) Old-Code 860 (Hebr.) Flarro 863 (Hebrew) Table 865 (Hebrew) CP775 Baltic CP1257 Baltic Mazovia (Poland) Kamenicky (Czech) CP866 Ukraine CP866 Kazakhstan ESC R Parameter 2E 2F 6D 6E 4D 4F 81 83 98 99 9A A6 77 92 91 8F 90 64 Tally Dascom 1140 11.3 Code Page Tables CP 437 (US) CP 737 Greek 65 Tally Dascom 1140 CP 850 (Multilingual) CP 851 66 Tally Dascom 1140 CP 852 (Eastern Europe) CP 857 (Turkish) 67 Tally Dascom 1140 CP 858 CP 860 (Portugal) 68 Tally Dascom 1140 CP 861 (Iceland) CP 863 (French-Canadian) 69 Tally Dascom 1140 CP 864 Arabic CP 864 Arabic Extended 70 Tally Dascom 1140 CP 865 (Norway) CP 866 (Cyrillic) 71 Tally Dascom 1140 CP 866 Bulgaria CP 1250 Win Latin 2 72 Tally Dascom 1140 CP 1251 Win Cyrillic CP 1252 Win Latin 1 73 Tally Dascom 1140 CP 1253 Win Greek CP 1254 Win Turkish 74 Tally Dascom 1140 8859-1 Latin 1 8859-1 Latin 1 (SAP) 75 Tally Dascom 1140 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 76 Tally Dascom 1140 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 77 Tally Dascom 1140 ISO 8859-15 Euro (Code Page 923) BRASCII 78 Tally Dascom 1140 Abicomp Roman 8 79 Tally Dascom 1140 Coax/Twinax (Hebrew) New-437 (Hebrew) 80 Tally Dascom 1140 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 81 Tally Dascom 1140 Flarro 863 (Hebrew) 865 Hebrew 82 Tally Dascom 1140 CP 1257 866 Ukraine 83 Tally Dascom 1140 866 Kazakhstan Kamenicky 84 Tally Dascom 1140 Mazovia CP 775 85 Tally Dascom 1140 CRO-ASCII Arabic Farsi 86 Tally Dascom 1140 Arabic Urdu Greek DEC 87 Tally Dascom 1140 Greek ELOT 928 88 Tally Dascom 1140 12 Control Codes Summary 12.1 Epson Emulation Command List Command Function BEL BS HT LF VT FF CR SO SI DC2 DC4 CAN ESC SO ESC SI ESC SP ESC !
ESC #
ESC $
ESC %
ESC &
ESC ( -
ESC ( B ESC ( C ESC ( G ESC ( U ESC ( V ESC ( ^
ESC ( c ESC ( t ESC ( v ESC *
ESC +
ESC -
ESC . ESC 0 ESC 2 ESC 3 ESC 4 ESC 5 ESC 6 ESC 7 ESC :
Beeper Backspace Horizontal Tab Line Feed Vertical Tab Form Feed Carriage Return Double-Wide Printing 1 Line Select Condensed Mode Cancel Condensed Mode Cancel Double-Wide Printing 1 Line Cancel Line Double-Wide Printing 1 Line Select Condensed Mode Set Inter Character Space Master Select Cancel MSB Control Set absolute horizontal print position Select user-defined set Define user-defined characters Select line/score Bar code setup and print Set page length in define unit Select graphics mode Set unit Set absolute vertical print position Print data as characters Set page format Assign character table Set relative vertical print position Select bit image Select n/360 Line Spacing Auto Underscore Print raster graphics Select 1/8 Line Spacing Select 1/6 Line Spacing Set Graphics Line Spacing (n/180) Select Italic Mode Cancel Italic Mode Enable Printable Characters Enable Upper Control Codes Copy ROM to RAM 89 Tally Dascom 1140 Command ESC <
ESC =
ESC >
ESC ?
ESC @
ESC A ESC B ESC C ESC C 0 ESC D ESC E ESC F ESC G ESC H ESC J ESC K ESC L ESC M ESC N ESC O ESC P ESC Q ESC R ESC S ESC T ESC U ESC W ESC Y ESC Z ESC \
ESC c ESC g ESC k ESC l ESC p ESC q ESC t ESC w ESC x ESC y ESC Y DEL Function Select Unidirectional Mode 1 Line Set MSB to 0 Set MSB to 1 Reassign Graphics Mode Initialize Printer Set n/60 Line Spacing Set Vertical Tabs Set Page Length in Lines Set Page Length in Inches Set horizontal tabs Select Emphasized Mode Cancel Emphasized Mode Select Double-strike Mode Cancel Double-strike Mode Advance print position Select 60-dpi graphics Select 120-dpi graphics Select 12 cpi Set bottom margin Cancel bottom margin Select 10 cpi Set right margin Select an international character set and code page Select Subscript or Superscript Printing Cancel Subscript or Superscript Printing Turn unidirectional mode on/off Turn Double-wide Mode On/Off Select 120-dpi, double-speed graphics Select 240-dpi graphics Set relative horizontal print position Set horizontal motion index(HMI) Select 15 cpi Select Typestyle Family Set left margin Turn Proportional Mode On/Off Select Character Style Select character table Turn Double-high Mode On/Off Select Letter Quality or Draft Select draft/super draft Select High-speed Double-density Graphics Mode Delete Character 90 Tally Dascom 1140 12.2 IBM Emulation Command List Command BS HT CR ESC BS ESC HT ESC CR ESC D ESC X ESC d LF VT FF ESC LF ESC VT ESC FF ESC 0 ESC 1 ESC 2 ESC 3 ESC 4 ESC 5 ESC A ESC B ESC C ESC C NUL ESC J ESC N ESC O ESC [ \
ESC ]
SO SI DC2 DC4 ESC SO ESC SI ESC DC2 ESC DC4 ESC -
ESC :
ESC E ESC F ESC G Function Backspace Horizontal tab Carriage return Backspace Horizontal tab Carriage return Set horizontal tabs Set horizontal margins Relative mode inline forward Line feed Vertical tab Form feed Line feed Vertical tab Form feed Select 1/8 line spacing Select 7/72 line spacing Start text line spacing Set graphics line spacing Set top of form Automatic line feed Set text line spacing Set vertical tabs Set form length in lines Set form length in inches Graphics variable line spacing Set automatic perforation skip Cancel automatic perforation skip Set vertical units Reverse line feed Double-wide printing by line Condensed printing Select 10 cpi Cancel double-wide printing by line Double-wide printing by line Condensed printing Select 10 cpi Cancel double-wide printing by line Continuous underscore Select 12 cpi Select emphasized mode Cancel emphasized mode Select double strike mode 91 Tally Dascom 1140 Command Function ESC H ESC I ESC P ESC S ESC T ESC W ESC [ -
ESC [ @
ESC [ I ESC [ d ESC _ ESC 6 ESC 7 ESC =
ESC [ T ESC \
ESC ^
ESC K ESC L ESC Y ESC Z ESC [ g ESC [ f ESC [ p DEL DC1 DC3 CAN ESC BEL ESC DC1 ESC DC3 ESC CAN ESC Q ESC R ESC U ESC [ K ESC j ESC *
ESC 3(AGM) ESC A(AGM) ESC J(AGM) Cancel double strike mode Set print mode Proportional space mode Start subscript or superscript printing Cancel subscript or superscript printing Continuous double-wide printing Score select Set presentation highlight Set font global Set print quality Continuous over score Select character set 2 Select character set 1 Character font image download Set code page Print continuously from all character chart Print single character from all character chart Normal density bit image graphics Dual density bit image graphics Dual density bit image graphics High density bit image graphics High resolution graphics Setup barcode parameter Set barcode data Beeper Select printer Deselect printer Cancel Data Beeper Select printer Deselect printer Cancel Data Deselect printer Set all tabs to power on settings Set print direction Set initial condition Stop printing Select graphics mode Set graphics line spacing(n/180") Set text line spacing(n/60") Graphics variable line spacing(n/180") 92 Tally Dascom 1140 FCC STATEMENT Changes or modifications not expressly approved by the responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 93 Tally Dascom 1140 Tally Dascom 1140 DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House,Priestley Road, Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com AMERICAS Dascom Americas Corporation 34 Lakeview Court Verona, VA 24482 USA Phone:+1 (877) 434 1377 Fax: +1 (540) 242 7221 www.dascom.com CHINA JIANGMEN DASCOM COMPUTER PERIPHERALS CO., LTD No.399, jinxing Road, Jianghai District Jiangmen, P.R. China www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent
#29-81,WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. 2015 DASCOM
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-03-24 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-03-24
|
||||
1 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021247903
|
||||
1 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 |
Jiangmen City Guang Dong Province, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
f******@us.tuv.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Z7O
|
||||
1 | Equipment Product Code |
TD11400
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y****** H********
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
0750-********
|
||||
1 | Fax Number |
0750-********
|
||||
1 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Dot Matrix Printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
EMTEK (DONGGUAN) CO.,LTD
|
||||
1 | Name |
S******** L********
|
||||
1 | Telephone Number |
86-76********
|
||||
1 | Fax Number |
86-76********
|
||||
1 |
s******@emtek.com.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC