all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 2.22 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | native | ||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Users Manual | Users Manual | 2.22 MiB |
User Manual DL-210 Label & Barcode Printer Tally Dascom DL-210 User Guide V1.2 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. The device and mains-socket must all times be easily accessible. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this user guide in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances. Ensure the printer is connected to a socket with the correct voltage. Always disconnect the printer from the power before opening the device to perform maintenance work or remedy errors. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Make sure that both the printer and the computer is switched off before connecting the data cable. The print head will become very hot during printing; avoid contact with the print head after printing has finished. Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. I Tally Dascom DL-210 User Guide V1.2 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor Sie den Drucker in Betrieb nehmen. Das Gert und die Netzsteckdose mssen jeder Zeit leicht zugnglich sein. Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Stoffen auf. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Keine Flssigkeiten mit dem Drucker in Berhrung bringen. Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit abkhlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. II Tally Dascom DL-210 User Guide V1.2 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service. Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un Le dispositif et la prise principale doivent toujours tre accessibles facilement. dpanneur qualifi. Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber. Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de substances explosives. Ne connecter limprimante une prise que lorsque la tension est correcte. Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension et toujours dbrancher le connecteur secteur de la prise murale. Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la poussire. Ne pas mettre limprimante en contact avec des liquides. Ne pas exposer limprimante des chocs, impacts ou vibrations. Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de donnes. La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir quelques instants avant dy toucher. N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. III Tally Dascom DL-210 User Guide V1.2 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili. tecnico di assistenza qualificato. Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. Evitare il contatto della stampante con liquidi. Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. IV Tally Dascom DL-210 User Guide V1.2 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un El dispositivo y la toma de corriente deben estar ubicados de forma que sea fcil acceder a ellos. tcnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sunstancias explosivas. Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentacin del enchufe. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegrese de que la impresora y el ordenador estn apagdos antes de conectar el cable de datos. La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarlo algn tiempo antes de tocarla. No permita que se realice cualquier operacin o accin de una forma diferente a lo que se seala en el manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. V Tally Dascom DL-210 User Guide V1.2
. (Russian)
, . VI Tally Dascom DL-210 User Guide V1.2 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora. A impressora e a tomada devem ser facilmente em todos os momentos acessveis. Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou substncias explosivas. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. No exponha a impressora a temperaturas altas ou luz solar direta. No aproxime substncias lquidas da impressora. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de Proteja a impressora de choques, impactos e vibraes. toc-la. No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, contate seu revendedor ou companhia de servio. VII Tally Dascom DL-210 User Guide V1.2 nemli Gvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatle okuyun. Cihaz ve elektrik prizinin her zaman kolayca eriilebilir olmas gerekir. Bakm ve tamir almalarn kesinlikle ve hibir surette kendi banza yapmayn; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazcy, zerinden yere dmesi mmkn olmayacak sabit ve dz bir zemine yerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veya patlayc maddeler ieren nesnelerin yaknna koymayn. Yazc akm kablosunu sadece doru gerilime sahip bir prize takn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zaman prizden kartn. Yazc hibir sv maddeyle temasta olmamaldr. Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalan meknlarda bulundurun. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapal olduklarndan emin Yazc hibir sarsntya, darbeye veya titreime mruz kalmamaldr. olmalsnz. Yazcnn ba basma esnasnda yksek sya ulayor. Bu yzden ltfen dokunmadan nce ksa sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfen imlatnza veya mteri hizmetleri servisinize bavurun. VIII Tally Dascom DL-210 User Guide V1.2 TRADEMARK ACKNOWLEDGEMENTS IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7,Windows 8, Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008/2013 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom DL-210 User Guide V1.2 TABLE OF CONTENTS 1 INTRODUCTION
...................................................................................................................... 1 1.1 DL-210 Thermal Printers 1.2 Unpacking 1.3 Placing the Printer 1.4 Printer Components
................................................................................................................ 1
....................................................................................................................................... 1
......................................................................................................................... 3
....................................................................................................................... 4 2 GETTING STARTED
.................................................................................................................. 7 2.1 Attaching Power 2.2 Loading Roll Media 2.3 Loading Transfer Ribbon 2.4 Print a Parameter Setting Page (Self-test Page) 2.5 Connecting the Interfaces
............................................................................................................................. 7
........................................................................................................................ 8
.............................................................................................................. 10
.......................................................................... 12
............................................................................................................ 13
.............................................................................................. 13
............................................................................................ 13
......................................................................................... 14
....................................................................................... 14
....................................................................................... 14
............................................................................................... 14
............................................................................................................................ 21 2.5.1 Connecting USB interface 2.5.2 Connecting serial interface 2.5.3 Connecting parallel interface 2.5.4 Connecting Ethernet interface 2.5.5 Connecting Wireless interface 2.5.6 Connecting to Bluetooth 2.6 Installing Driver 3 OPERATION GUIDE
................................................................................................................. 28 3.1 Control Panel Operation 3.1.1 LEDs Behavior 3.1.2 Feed Key Operation 3.2 Setup Tool Application 3.2.1 Model and Interface Setting 3.2.2 Configuring Printer 3.2.3 Update Firmware 3.3 Auto Calibrate Label
.............................................................................................................. 28
............................................................................................................... 28
....................................................................................................... 28
................................................................................................................. 29
.......................................................................................... 29
........................................................................................................ 29
.......................................................................................................... 31
.................................................................................................................... 33 4 TROUBLESHOOTING AND MAINTENANCE
............................................................................... 34 4.1 Common Issues 4.2 Resetting the Factory Default Values 4.3 Removing Jammed Label 4.4 Cleaning Thermal Print Head 4.5 Maintenance
............................................................................................................................ 34
.......................................................................................... 35
............................................................................................................. 35
....................................................................................................... 35
................................................................................................................................ 35 5 SPECIFICATIONS
..................................................................................................................... 37 5.1 Printer specification 5.2 Communication Interfaces 5.2.1 USB interface 5.2.2 Wi-Fi interface 5.2.3 Bluetooth Interface 5.2.4 Ethernet interface 5.2.5 Serial interface
..................................................................................................................... 37
.......................................................................................................... 38
................................................................................................................ 38
.............................................................................................................. 38
....................................................................................................... 38
......................................................................................................... 38
.............................................................................................................. 39 Tally Dascom DL-210 User Guide V1.2 5.2.6 Parallel interface
........................................................................................................... 39
............................................................................................................................... 40 5.3 Power Supply 6 CODE PAGES
........................................................................................................................... 42 6.1 Common to all pages (International Character Set: USA) 6.2 International Character Sets 6.3 [User-defined page]
6.4 [PC437: USA, Standard Europe]
6.5 [PC850: Multilingual]
6.6 [PC852: Latin2]
6.7 [PC858: Euro]
6.8 [PC860: Portuguese]
6.9 [PC863: Canadian-French]
6.10 [PC865: Nordic]
6.11 [PC866: Cyrillic #2]
6.12 [PC720: Arabic]
.......................................................... 42
........................................................................................................ 43
..................................................................................................................... 44
................................................................................................... 45
................................................................................................................... 46
............................................................................................................................. 47
............................................................................................................................... 48
.................................................................................................................... 49
........................................................................................................... 50
.......................................................................................................................... 51
..................................................................................................................... 52
........................................................................................................................... 53 7 COMMAND SETS
.................................................................................................................... 54 7.1 ESC/POS Command Sets 7.2 ZPL Command Sets
.............................................................................................................. 54
....................................................................................................................... 56 Appendix: Installing the Cutter
.................................................................................................. 62 Disintall the Tear Bar Install the Auto Cutter
.......................................................................................................................... 62
....................................................................................................................... 63 Appendix: FCC STATEMENT
........................................................................................................ 66 Appendix: DASCOM REPRESENTATIVES
...................................................................................... 67 Tally Dascom DL-210 User Guide V1.2 1 INTRODUCTION 1.1 DL-210 Thermal Printers The Dascom DL-210 model is the best value in a desktop thermal printer. The DL-210 printer provides thermal transfer and direct thermal printing at speeds up to 6 ips (inches per second) at a 203 dpi (dots per inch) print density. The DL-210 printer features:
Automatic printer language detection and switching between ZPL and EPL programming and label formats. Easy operation. With open structure users can easily change paper roll and ribbon. Large media compartment. Ribbon as long as 300m and paper roll of Max. OD 127mm can be used. Therefore users can change the ribbon and paper roll less often so as to work more efficiently. Wide range of connectivity. The USB interface is standard interface. Serial/parallel/Ethernet/ Wi-Fi/
Bluetooth are optional interfaces. Various interface choices suit all needs. The DL-210 printers offer these basic printer options:
Auto cutter. Label Dispense (Peel-Off). This user guide provides all the information you need to operate your printer on a daily basis. 1.2 Unpacking When you receive the printer, please check for possible shipping damage:
1. Inspect the outside of both the box and the printer for possible damage. 2. Open the top cover of the printer to see if the media compartments are in order. If you discover shipping damage upon inspection:
Immediately notify the shipping company and file a damage report. Keep all packaging material for shipping company inspection. Notify your authorized Tally Dascom reseller. 1 Tally Dascom DL-210 User Guide V1.2 DL-210 printer Ribbon Power cord Media CD-ROM Power Adapter Ribbon Rewind Paper Core The package contents vary with different customized order requirements. 2 Tally Dascom DL-210 User Guide V1.2 Package Contents:
Printer Ribbon rewind paper core Ribbon sample Ribbon spindle Media sample Media fixer Media spindle Power adapter Power cord Graphic installation guide Standard 1 unit 1 piece 1 piece Wax 2 pieces 1 piece 2 pieces 1 piece 1 piece 1 piece 1 piece CD-ROM Peeler Cutter Optional 1.3 Placing the Printer 1 piece 1 set 1 set Thermal transfer EU/UK/US Including user guide, Driver, setup tool, graphic installation guide) Select a solid, level surface within reach of an available power outlet. To allow for proper ventilation and cooling, leave open space on all sides of the printer. After placing the printer, be aware of the following rules:
Never place the printer near to any flammable gas or explosive substances. Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. Ensure sufficient distance between the printer and any heating devices or radiators. Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. 3 Tally Dascom DL-210 User Guide V1.2 1.4 Printer Components Printer components and their functions are shown as below:
Media Window Top Cover Optional Interface
(Serial/ Parallel/
Ethernet/
Wi-Fi/ Bluetooth Component Name Media window Top cover Power LED Status LED Error LED Feed key Control Panel Power socket Power switch USB interface Optional interface
(Serial/ Parallel/ Ethernet/ Wi-Fi/
Bluetooth) Control Panel Power Switch Power Socket USB interface Function Monitor the media status via this window Open this cover for loading ribbon and media Indicate the power status Indicate the status of media, ribbon and label-taken Indicate print head temperature and Print head mechanism open or not Press this key for feeding media Connect power cord to the printer For switching on/off printer Connect USB interface cable from host Connect optional interface cable from host
(interface type is on request) 4 Tally Dascom DL-210 User Guide V1.2 Ribbon Pick-up Holder Print Head Mechanism Media Holder Print Head Locking Button Print Head Tear Bar Function For placing ribbon, lower seat for new ribbon, top seat for used ribbon. Heat the ribbon and transfer imaging components to the media Turn the adjustor for stretching ribbon For placing media For closing or opening the print head mechanism For tearing the media Disassemble the rotatable board for installing optional kit: peeler or cutter 5 Ribbon Holder Print Head Locking Button Ribbon Pick-up Holder Rotatable Board Ribbon Holder Print Head Component Name Print Head Mechanism Ribbon Pick-up Holder Media Holder Print Head Locking Button Tear Bar Rotatable Board Tally Dascom DL-210 User Guide V1.2 Media Guide Media Guide Adjuster Media Sensor Black Mark Sensor Platen Roller Component Name Media Guide Media Guide Adjustor Media Sensor Black Mark Sensor Platen Roller Function Align the media in the center of media path Adjust the space between the two media guides For detecting media For detecting black mark. The sensor position can be adjusted according to the black mark position. For feeding paper Media Fixer Media Spindle Ribbon Rewind Paper Core Ribbon Spindle Component Name Media Spindle Media Fixer Ribbon Spindle Ribbon Rewind Paper Core Function Insert it into media core for supporting media For fixing media (as the above figure shown) Install it in ribbon holder for supporting ribbon or ribbon rewind pipe Stick the used end of ribbon to the pipe, rewind ribbon while the pipe is turning 6 Tally Dascom DL-210 User Guide V1.2 2 GETTING STARTED 2.1 Attaching Power Before you connect the power adapter to the power socket check if the voltage is correct. If you connect the power adapter to power with incorrect voltage this may result in electrical damage to the adapter and the printer.
(1) Make sure power off the printer and the computer/host.
(2) Insert the AC power cord into the power supply.
(3) Insert the power supplys power connector into the printers power receptacle.
(4) Plug the other end of the power cord into an appropriate AC electric outlet.
(5) Load the media and the ribbon before powering on printer. Wait until power LED is on. After switching off the printer, wait at least 5 seconds before powering on again. Otherwise, it may cause damage to the printer. Please disconnect the power supply if the printer is idle for a long time. 7 Tally Dascom DL-210 User Guide V1.2 2.2 Loading Roll Media Must use thermal media in case of no ribbon in the printer. If using ribbon, you have to use thermal transfer media. Tips for avoiding media jam: Make sure the media is aligned in the center of the printer and the media fixers are firmly pressed against both sides of the roll. Before printing, it is necessary to check whether the media you use is appropriate or not. You can scratch the media surface, if the scratch turns black, it is direct thermal media. In this case, you do not need to load ribbon. Otherwise, it is thermal transfer media, you have to use ribbon.
(1) Lift the top cover to expose the media holder and the print head mechanism.
(2) Load the media roll onto the spindle from left to right.
(3) Put the fixers on and move from right to left until they lean against the media.
(4) Click the media spindle back into the media holder. Print surface must be upward.
(5) Unlatch the print head mechanism by pushing the two blue locking buttons on the sides toward the rear. 8 Tally Dascom DL-210 User Guide V1.2
(6) Lead the media under the print head mechanism through the media guides.
(7) Control the blue media guide adjustor so as to align the media in the central path.
(8) Lead the media over the platen roller and through the tear bar. Black mark sensor must be covered by label rather than label gap. Otherwise, the contents may exceed label area.
(9) Put the print head mechanism down and press down firmly until you hear a snap.
(10) Close the top cover and turn on the printer or press the FEED button if the printer is already on.
(11) In order to make sure the data is printed within the label area, it is necessary to execute Label Calibration: Hold down Feed Key and switch on printer simultaneously, release Feed Key after the buzzer beeps twice. Then the label will be positioned automatically. Label calibration should be executed in the following situations:
Use printer for printing label first time. Replace different size of labels. Printer skips labels Printer feeds blank labels. 9 Tally Dascom DL-210 User Guide V1.2 2.3 Loading Transfer Ribbon Transfer ribbons come in several varieties and in some cases colors to match your application needs. The media and ribbon types should be matched to provide you with optimal print results. Always use ribbon that is wider than the media to protect the printhead from wear. For direct thermal printing, do not load ribbon in the printer. Do not use ribbon while using thermal media. Otherwise, barcode and graph will be distorted.
(1) Lift the top cover to expose the media holder and the print head mechanism.
(2) Unlatch the print head mechanism by pushing the two blue locking buttons on the sides toward the rear.
(3) Unwrap the ribbon roll pack and separate the ribbon roll and the bare paper core.
(4) Insert the spindles into the core and the ribbon respectively.
(5) Attach the edge of the ribbon on the bare paper core and wind it a little onto the core. Do not rip the ribbon leader on ribbon rewind pipe. Do observe the direction of hexagon. 10 Tally Dascom DL-210 User Guide V1.2
(6) Insert the ribbon roll into the ribbon holder
(lower seat of the print head mechanism): Insert the hexagon end onto the ribbon adjustor (blue gear), then insert the other end into the slot of the ribbon holder.
(7) Turn back the print head mechanism and then insert the ribbon rewind paper core into the pick-up holder (top seat): Wind the ribbon through print head, and insert the spindle hexagon end onto the ribbon adjustor (blue gear), then insert the other end into the slot of the pick-up holder. Keep the brighter surface of ribbon inside while winding the print head.
(8) Turn the wheel of the print head mechanism to ensure the ribbon is tightly wound.
(9) Press down the print head mechanism firmly until you hear a snap. 11 Tally Dascom DL-210 User Guide V1.2 2.4 Print a Parameter Setting Page (Self-test Page) Before you connect the printer to the computer, make sure that the printer is in proper working order. You can do this by printing a configuration status label. 1. Make sure the media is properly loaded, the top cover of the printer is closed and the printer is power off. Then, press and hold the Feed button once you are ready. 2. Hold down Feed Key and then switch on printer till Power LED blinks once, buzzer beeps once. 3. The printer will print out a parameter setting page. Here is the self test page and its explanation:
Model Serial Number ID Number F/W Interface type Emulation supported Media type Printing method Printhead life Sensor Memory size Density Peeler status Black mark status Cutter status Detect lack of media Auto verify label status Detect postion status Page mode status Current printing speed Current printing width Parameter settings DL-210 XXXXXXXXXXXX 28.904.XX Model SN NO ID NO Firmware versio................................20.00.08 Interface...................................................USB Emulation..............................................ZPLII Media.....................................................Label Print Type................................Direct Thermal Print count..................................................0m Sensor AD.1_0 2_1 D_480 B_517 50.0 2.0 Memory................................................8192K Print Density..................................................1 Peeler.........................................................Off Black Mark................................................Off Cutter.........................................................Off Paper end detection....................................On Auto verify label........................................Off Detect print position..................................Off Page mode..................................................On Print Speed.......................................150mm/s Print Width........................108mm (8dot.mm) Complete Dascom 12 Tally Dascom DL-210 User Guide V1.2 2.5 Connecting the Interfaces The USB interface is standard interface. Serial/parallel/ Ethernet/ Wi-Fi/ Bluetooth are optional interfaces. All interfaces are located at the rear of the printer. Choose the interface which suits your system. Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports. 2.5.1 Connecting USB interface 2.5.2 Connecting serial interface 13 Tally Dascom DL-210 User Guide V1.2 2.5.3 Connecting parallel interface 2.5.4 Connecting Ethernet interface 2.5.5 Connecting Wireless interface Users have to prepare a Wlan card by themselves and install it in the Wi-Fi interface. 2.5.6 Connecting to Bluetooth Communication cable is not required while using Bluetooth printer. Users have to prepare a Bluetooth adapter by themselves and install the adapter in the computer so as to connecting the Bluetooth device.
(1) First make sure the printer driver is installed. And then install Bluetooth adapter (V2.0 or above version) that prepared by yourself in the PC via USB interface. 14 Tally Dascom DL-210 User Guide V1.2
(2) Power on the printer and load the paper roll.
(3) Double click the Bluetooth icon at lower right corner on the PC screen. You will see the following window then Click Add a device.
(4) Select the Bluetooth printer, and then click Next. 15 Tally Dascom DL-210 User Guide V1.2
(5) Select Enter the devices pairing code in the pop-up dialog box. And then click Next.
(6) Input the default PIN code 0000, and then click next. 16 Tally Dascom DL-210 User Guide V1.2
(7) Then the Bluetooth adapter has been installed in the computer.
(8) Check the Device and Right click Dascom DL-210, select Printer Properties. Check the Bluetooth serial port name. 17 Tally Dascom DL-210 User Guide V1.2
(9) The Bluetooth port name is COM4 in this case. 18 Tally Dascom DL-210 User Guide V1.2
(10) Right click any printer, select Properties Interface, and select the output port that you have put down (in the case COM4) then click Apply. 19 Tally Dascom DL-210 User Guide V1.2
(11) Select General Print Test Page, run test page to see the printing outcome. Setting pages vary depending on the different types of Bluetooth adapter. 20 Tally Dascom DL-210 User Guide V1.2 2.6 Installing Driver Switch off the printer before running the printer driver setup. Your printer CD-ROM comes with Windows Driver. Go to the Driver folder and run the installer.
(1) Click Next. 21 Tally Dascom DL-210 User Guide V1.2
(3) Select the installation path to the Driver. 22 Tally Dascom DL-210 User Guide V1.2
(3) Click Finish.
(4) Click Yes. 23 Tally Dascom DL-210 User Guide V1.2
(5) Click Next.
(6) Choose interface. 24 Tally Dascom DL-210 User Guide V1.2
(7) Choose printer model Tally Dascom DL-210Z, and the installation path. Then click Next.
(8) Click Next. 25 Tally Dascom DL-210 User Guide V1.2
(9) Enter printer name. Click Next.
(10) Click Finish. 26 Tally Dascom DL-210 User Guide V1.2
(11)Then the driver is installed successfully. 27 Tally Dascom DL-210 User Guide V1.2 3 OPERATION GUIDE Status Power on. Error or power off. Paper end. Normal. 3.1 Control Panel Operation 3.1.1 LEDs Behavior LEDs LEDs behavior On Off On Off Power Status Error Fast blink Label remains in peeler. Slow blink Ribbon end. On Off Print head mechanism is opened. Normal. Fast blink Print head is over-heated. 3.1.2 Feed Key Operation Feed Paper Under ESC/POS mode, presses Feed Key once, feed paper one line (30 steps);
Under ESC/POS mode, hold down Feed Key without release, feed paper continuously;
Under ZPL/EPL mode, press Feed Key once, feed one piece of label;
Under ZPL/EPL mode, hold down Feed Key without release, feed labels continuously. Hexadecimal dump Hold down Feed Key and switch on printer till Power LED blinks three times, buzzer beeps three times. When self-test is OK but on-line printing error occurs, you can check the communication between PC and program via Hexadecimal Dump mode. In Hexadecimal Dump mode, the printer will print out hexadecimal data once it receives the signal from host. You can ask technical service for analysis. 28 Tally Dascom DL-210 User Guide V1.2 3.2 Setup Tool Application A CD comes along with printer. The CD contains POS & label printer setup tool for configuring printer. Or, please find the latest setup tool on Dascom website: www.dascom.cn Read the help file carefully before using the setup tool. Please click Help button in Choose Interface tab for more information. 3.2.1 Model and Interface Setting Select model number and available interface before configuring printer. Click setting for setting serial interface or parallel interface. For serial interface setting, the setting wont be valid unless you restart the printer. 3.2.2 Configuring Printer After model and interface setting, select Internal Setup tab for configurations. 29 Tally Dascom DL-210 User Guide V1.2 Setup Items Explanation Options Setup Items Page Mode On, Off Default On Description Use un-continuous paper select on; Use continuous paper select off. Print Media Label Paper, Continuous Paper Label Paper Select the actual media type. Peeler Off, On Off Enable peeler or not Print Method Thermal Transfer, Direct Thermal Thermal Transfer Print Density 1, 2, 3, 4, 5 1 Printer Language English, Chinese English Emulation ESC/POS, ZPL, EPL Print Speed 1, 2, 3, 4 Black Mark Detection Black Mark to Home Black Mark to Cutter On, Off User-define User-define ZPL 4 Off 20 40 Use ribbon select thermal transfer; Use thermal paper select direct thermal Adjust print density. Level 1 is lowest, Level 5 is highest. Set the printers system language, Chinese or English. Select ZPL/EPL while using un-continuous paper;
Select ESC/POS while using continuous paper. Adjust the print speed. Level 1 is lowest, Level 4 is highest. Enable black mark detection or not. Set the vertical distance between print home position and the top of black mark. Set the vertical distance between cutting position and the top of black mark. 30 Tally Dascom DL-210 User Guide V1.2 Cutter Switch On, Off On, Off On, Off On, Off Print Position Detection Auto Calibrate Label Paper End Detection Black mark AD value Off Off Off On Enable cutter or not Enable print position detection or not On: It will auto calibrate the label when you use a different size label. Off: Disable auto calibrate label On: Detect the printer's paper is empty or not. Off: Disable paper end detection. User-define 789 It can make the black mark detection more accurately according to the AD value. Explanation for Buttons Button Get Printer Setting Description When printer is powering on, click this button for acquiring the current setup menu. It will display on the screen. Print Self-test Click this button for printing self-test printout. Restore All Setting Click this button for restore all setting. Send Setting The new setting will be valid if click this button. If no any change, it will keep the default value. After setting, the printer will beep once, then the setting become valid. In order to enhance print head lifetime, it is recommended that setting low print density if print quality is satisfactory. 3.2.3 Update Firmware
(1) Preparation USB cable, 24V power adapter, DL-210 setup tool, firmware file.
(2) Connection Connect printer and host with USB cable firmly. Check the Device Manager, if connection is successful, USB printing support will display under universal serial Bus Controllers directory. Otherwise, please check the connection between printer and USB interface, please check whether the Driver installation is successful or not. 31 Tally Dascom DL-210 User Guide V1.2
(3) Enter Upgrade Mode Lift up top cover and turn up print head mechanism Print head mechanism Hold down Feed Key and switch on printer simultaneously. Release Feed Key once powering on, the printer will beep once. Status LED on, printer enter upgrade mode.
(4) Upgrade Firmware Run DL-210 setup tool, select model DL-210 and USB interface. Select Update Firmware tab, then click Browse for searching the firmware file, click Update at last. 32 Tally Dascom DL-210 User Guide V1.2 After firmware loading, press Feed Key when Error LED and Status LED blink. Restart the printer after printer beeps twice. 3.3 Auto Calibrate Label DL-210 can calibrate label automatically. Hold down Feed Key and switch on printer till Power LED blinks twice, buzzer beeps twice. Label calibration should be executed in the following situations:
Print label first time Replace different size of labels Printer skips labels Printer feeds blank labels 33 Tally Dascom DL-210 User Guide V1.2 4 TROUBLESHOOTING AND MAINTENANCE Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, please contact your dealer for assistance. Read the following instructions before maintenance and avoid incorrect operation, so as to prevent injury to you and damage to the printer. 4.1 Common Issues LED Indication and Buzzer Alarm Condition Possible Cause What to do?
Unplug power cord Check power cord and plug it properly No LEDs on Turn off printer PCB damaged Turn on printer Contact service representatives Status LED always on Media end Re-load media Error LED always on Print head mechanism open Close the print head mechanism Status LED blinks Label remains in peeler Remove label Ribbon end Replace ribbon Thermal print head overheated Turn the printer off and wait some minutes before resume Over-voltage Low-voltage Print with specified voltage Print with specified voltage Error LED blinks and buzzer alarms Printing Error Condition Possible Cause What to do?
Incorrect media roll installation Check media roll and re-load it properly Media is out of specification Use recommended media Blurred or spot printing Dirty thermal print head or platen Clean print head or platen Ribbon is out of specification Use recommended ribbon Low print density Increase the print density Self-test fail Hardware problem Contact service representatives Media jam Label stuck Printer skips labels Printer feeds blank labels Label positioning problem or label size setting exceeds the physical size. Check media path and clean jammed label, refer to Chapter 3 Section 3.2 Execute label calibration (refer to Chapter 2 Section 2.1.2). If it doesnt work, you have to verify the label size setting is correct or not. 34 Tally Dascom DL-210 User Guide V1.2 4.2 Resetting the Factory Default Values Sometimes, resetting the printer to the factory defaults may solve some problems. There are two methods to set to factory setting:
Method one: Hold down Feed Key and switch on printer till Power LED blinks four times, buzzer beeps four times. Method two: through setup tool, choose restore all setting on printer setup page. 4.3 Removing Jammed Label Print head may be hot, please do not touch!
(1) Turn printer off, open top cover and turn up print head mechanism.
(2) Remove the jammed label and ribbon, clean the print head with alcohol in case of ribbon paste on print head and cause poor print quality.
(3) Reload media.
(4) Reload ribbon and turn the ribbon adjustor for rewinding the sticky part. 4.4 Cleaning Thermal Print Head After printing, the thermal print head becomes very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the thermal print head by touching it with your fingers or any hard object. Turn off the printer, open the top cover and remove ribbon, clean the thermal elements of the print head with a cotton swab moistened with alcohol solvent (ethanol, methanol, or isopropyl). We recommend cleaning the thermal print head periodically (generally every 3 months) to maintain print quality. 4.5 Maintenance DL-210 is designed for a long and reliable lifetime. But periodic maintenance is recommended in order to assure error free working. This also would guarantee the good print quality over the life time. It is recommended to clean the printer once every six months or after 300 hours duty. Before cleaning, switch off the printer, wait a few seconds and unplug the power cord. Open the cover and remove the dust, paper shreds and other debris from inside by using a soft vacuum cleaner or a brush. In order to remove the dirt, you can wipe clean the machine with a soft cloth dipped in alcohol 35 Tally Dascom DL-210 User Guide V1.2 instead of the ketone or TEC solvent which may cause damage to the plastic parts. Please be aware that excessive moisture will lead to the improper functioning of electronic parts. Clean the platen roller with soft cloth. While you are cleaning the printer, in order to avoid short circuit, do not damage or loose the cable or electronic parts, do not drop metal material inside, such as Paper Clips or Pins. 36 Tally Dascom DL-210 User Guide V1.2 5 SPECIFICATIONS 5.1 Printer specification Print Parameter Fonts Print method Print width Print speed Print head Resolution Chinese Alphanumeric User-defined Code Pages Scalable/Rotation Graphics Barcodes Ribbon 1D 2D ID OD Length Width Media Spec. Media Handling Control Panel Detect Function Emulation Power Supply Memory Media cut Media type Key LED indicator Standard sensors Optional kit sensor Zebra, EPSON Input Output SDRAM FLASH Standard Interface Optional Direct thermal/Thermal transfer printing 108mm 150mm/s (203DPI) Dot pitch: 0.125mm 203DPIx203DPI GB18030 2424 (Simplified/Traditional Chinese) Resident single byte (ZPL): Font A ~ Font V User-defined fonts can be downloaded into FLASH, SDRAM. PC437, PC850, PC860, PC863, PC865, PC858, PC852, PC866, PC720 Zoom in 1~8 times in vertical or horizontal, rotate by 00, 900, 1800, 2700. Graphics (Monochrome PCX, BMP) can be downloaded into FLASH, SDRAM. Code 39,UPC-A,UPC-E,Matrix 25, Industrial 2 of 5, Interleaved 2 of 5, Post 2 of 5(China),Code 128, EAN-13, EAN-8, HBIC(Code 39), Codabar, UPC2,UPC5, Code93,UCC/EAN Code PDF417, MaxiCode, QR Code, Data Matrix 25.4mm 68mm 300m 33~110mm Thickness 0.06~0.18mm Width 25~118mm Length 8.9~400mm Max. OD 127mm Min. ID 25.4/38.1mm Tear bar, auto-cutter, (peeler) Thermal paper, media, black mark paper. One key: Feed Three LEDs: Power, Error, Status (Paper out/Ribbon out) Black mark sensor, Media sensor, Ribbon sensor, Machinery sensor Label taken sensor ZPL, EPL, ESC/POS External power adapter AC 100V-240V, 50-60Hz 24V DC, 2A 8MB 8MB USB (2.0 Full-Speed) Serial (RS-232, DB25) Parallel Centronics (IEEE-1284) Ethernet: 10M/100M Wi-Fi (802.11b/g/n) Bluetooth: SPP 37 Tally Dascom DL-210 User Guide V1.2 Software Physical Spec. Safety Regulation Optional kit Dimensions Casing Color Weight Operating condition Storage condition Safety EMC Certificate Reliability TPH lifetime Driver (Windows 32bit/64bit, Linux), Barcode Easy, SDK system 230(W)290(D)176(H)mm Black, white Approx 3kg 540/2095%RH (non-condensing)
-2060/95%RH (non-condensing) GB 4943.2011 Class B CCC, CE, FCC, UL, Energy star Cutter, Peeler 150km
(Condition: use specific thermal roll paper and the print rate is 12%) 5.2 Communication Interfaces 5.2.1 USB interface USB interface pin assignment PIN No. Description Classic wire color 1 2 3 4 VBUS D-
D+
GND Red White Green Black USB interface connector diagram 5.2.2 Wi-Fi interface Wi-Fi interface supports 2.4 GHz, IEEE Std. 802.11b standard. 5.2.3 Bluetooth Interface Bluetooth version: Standard BT2.1+EDR Communication protocol: SPP Radio frequency: 2.4GHz Transmission distance: 10m 5.2.4 Ethernet interface Ethernet interface pin assignment Pin. No. 1 2 3 Name TX+
TX-
RX+
Description Tranceive Data+
Tranceive Data-
Receive Data+
38 Tally Dascom DL-210 User Guide V1.2 4 5 6 7 8 Ethernet interface connector diagram Not connected Not connected Receive Data-
Not connected Not connected n/c n/c RX-
n/c n/c 5.2.5 Serial interface Serial interface compatible with RS-232 standard, with 25 pin (D hole type) socket. Serial interface pin assignment PIN No. PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8~19 PIN 20 PIN 21~25 Description Frame Ground TXD RXD RTS Unconnected DSR Signal Ground Unconnected DTR Unconnected User can view the setting of interface via printing configuration sample. The default setting of serial interface is as follow, 38400 bps (baud rates), 8 bit (data bit), 1 bit (stop bit), no parity, support RTS/CTS handshaking protocol. Serial interface connector diagram 5.2.6 Parallel interface Parallel interface pin assignment Parallel interface with 36 pin CENTRONICS socket. Pin No. Signal From 1 H Description Strobe Signal; Data latch pulse, latch the data to the printer at the rising edge of the negative pulse. 39 Tally Dascom DL-210 User Guide V1.2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 H H H H H H H H P P P Data 0 (The lowest bit) Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 (The highest bit) ACK Signal; Printer response signal, indicates that the printer has received a Data byte. Busy Signal; The printer is busy; High level indicates that the printer cant receive data. PE Signal; Paper end signal; High level indicates that the printer is out of paper. Unconnected Unconnected Unconnected Logic Ground Frame Ground, separated from logic ground. 5V/500mA power output 19~30 Logic Ground 31 32 33 P Initialization signal Printer error signal. Low level indicates that an error occurs in the printer. It will come with paper end. Logic Ground 34~35 Unconnected 36 Unconnected Remarks:
H indicates that signal comes from Host computer; P indicates that signal comes from Printer. Parallel interface connector diagram 5.3 Power Supply
(1) Power adapter Input: AC 100V-240V~ 1.5A 50-60Hz Output: DC 24V5%, 2.1A, A-1009-3P interface
(2) Power Supply connector diagram 40 Tally Dascom DL-210 User Guide V1.2
(3) Power Socket pin assignment Pin Number Signal Name 1 2 3 SHELL
+24 V GND N.C F.G.
(4) Power Supply interface type Printer - Unetop DC-002 or similar products Computer - Unetop DP-002 or similar products 41 Tally Dascom DL-210 User Guide V1.2 6 CODE PAGES 6.1 Common to all pages (International Character Set: USA) 42 Tally Dascom DL-210 User Guide V1.2 6.2 International Character Sets 43 Tally Dascom DL-210 User Guide V1.2 6.3 [User-defined page]
44 Tally Dascom DL-210 User Guide V1.2 6.4 [PC437: USA, Standard Europe]
45 Tally Dascom DL-210 User Guide V1.2 6.5 [PC850: Multilingual]
46 Tally Dascom DL-210 User Guide V1.2 6.6 [PC852: Latin2]
47 Tally Dascom DL-210 User Guide V1.2 6.7 [PC858: Euro]
48 Tally Dascom DL-210 User Guide V1.2 6.8 [PC860: Portuguese]
49 Tally Dascom DL-210 User Guide V1.2 6.9 [PC863: Canadian-French]
50 Tally Dascom DL-210 User Guide V1.2 6.10 [PC865: Nordic]
51 Tally Dascom DL-210 User Guide V1.2 6.11 [PC866: Cyrillic #2]
52 Tally Dascom DL-210 User Guide V1.2 6.12 [PC720: Arabic]
53 Tally Dascom DL-210 User Guide V1.2 7 COMMAND SETS 7.1 ESC/POS Command Sets Category Commands LF Print commands FF CR ESC J n HT ESC $ nL nH ESC D n1...nk NUL ESC \ nL nH ESC a n ESC d n ESC t n GS L nL nH GS W nL nH ESC = n ESC @
GS P x y FS ! n FS &
FS - n FS FS 2 c1 c2 d1...dk FS C n FS S n1 n2 Print position commands Miscellaneous Function Commands Chinese Character control commands FS W n ESC 2 ESC 3 n ESC c 5 n Space commands Control panel commands 54 Function Print and line feed Print and feed paper to the head of next page (in page mode) Print and carriage return Print and feed paper Horizontal tab Set absolute print position Set horizontal tab positions Set relative print position Select justification Print and feed n lines Select character code table Set left margin Set print area width Select printer Initialize printer Set horizontal and vertical motion units Set Chinese character mode Select Chinese character mode Turn on/off Chinese character underline mode Cancel Chinese character mode Define user-defined Chinese character Select Chinese character code system Set Chinese character left and right spacing Turn on/off Chinese double height and double width Select default line spacing Set line spacing Enable/disable panel buttons Tally Dascom DL-210 User Guide V1.2 Category Commands ESC SP n ESC ! n ESC % n ESC & y c1 c2 [x1 d1...d(y x1)]...[xk d1...d(y xk)]
ESC - n Character control commands ESC ? n ESC E n ESC G n ESC M n ESC R n ESC V n ESC { n GS ! n GS B n GS H n GS f n GS h n GS k m d1...dk NUL GS k m n d1...dn GS w n ESC Z m n k dL dH d1 dn GS Z n GS k m v r d1...dn NUL GS k m v r nL nH d1...dn ESC * m nL nH d1... Dk FS P n GS * x y d1...d(x y 8) Barcode commands Bit image commands Function Set right-side character spacing Select print mode(s) Select/cancel user-defined character set Define user-defined characters Turn on/off underline mode Cancel user-defined characters Turn emphasized mode on/off Turn double-strike mode on/off Select character font Select an international character set Turn on/off 90 degrees clockwise rotation mode Turn on/off upside-down print mode Select character size Turn white/black reverse print mode on/off Select print position of HRI characters Select font for HRI characters Set bar code height Print bar code Set barcode width Print 2D barcode Select 2D barcode type Print 2D barcode Select bit-image mode Print NV bit image Define downloaded bit image 55 Tally Dascom DL-210 User Guide V1.2 7.2 ZPL Command Sets Commands Function
^A
^A@
^B0
^B1
^B2
^B3
^B4
^B5
^B7
^B8
^B9
^BA
^BB
^BC
^BD
^BE
^BF
^BI
^BJ
^BK
^BL Scalable/Bitmapped Font Use Font Name to Call Font Aztec Bar Code Parameters Code 11 Bar Code Interleaved 2 of 5 Bar Code Code 39 Bar Code Code 49 Bar Code Planet Code bar code PDF417 Bar Code EAN-8 Bar Code UPC-E Bar Code Code 93 Bar Code CODABLOCK Bar Code Code 128 Bar Code (Subsets A, B, and C) UPS MaxiCode Bar Code EAN-13 Bar Code MicroPDF417 Bar Code Industrial 2 of 5 Bar Codes Standard 2 of 5 Bar Code ANSI Codabar Bar Code LOGMARS Bar Code
^BM MSI Bar Code
^BO
^BP
^BQ
^BR
^BS
^BT
^BU
^BX
^BY Aztec Bar Code Parameters Plessey Bar Code QR Code Bar Code GS1 Databar (formerly Reduced Space Symbology) UPC/EAN Extensions TLC39 Bar Code UPC-A Bar Code Data Matrix Bar Code Bar Code Field Default
^CC ~CC Change Caret
^BZ POSTAL Bar Code 56 Tally Dascom DL-210 User Guide V1.2 Commands Function
^CD
^CF
^CI
^CM
^CO
^CP
^CV
^CW
~DB
~DE
^DF
~DG
~DN
~DS
~DT
~DU
~DY
~EG
^FB
^FC
^FD
^FH
^FL
^FM
^FN
^FO
^FP
^FR
^FS
^FT
^FV
^FW
^FX
^GB
~CD Change Delimiter Change Alphanumeric Default Font Change International Font/Encoding Change Memory Letter Designation Cache On Remove Label Code Validation Font Identifier Download Bitmap Font Download Encoding Download Format Download Graphics Abort Download Graphic Download Intellifont (Scalable Font) Download Bounded TrueType Font Download Unbounded TrueType Font Download Objects Erase Download Graphics Field Block Field Clock Field Data Field Hexadecimal Indicator Font Linking Multiple Field Origin Locations Field Number Field Origin Field Parameter Field Reverse Print Field Separator Field Typeset Field Variable Field Orientation Comment Graphic Box 57 Tally Dascom DL-210 User Guide V1.2 Commands Function
^GC
^GD
^GE
^GF
^GS
~HB
~HD
^HF
^HG
^HH
~HI Graphic Circle Graphic Diagonal Line Graphic Ellipse Graphic Field Graphic Symbol Battery Status Head Diagnostic Host Format Host Graphic Configuration Label Return Host Identification
~HM Host RAM Status
~HQ
~HQ
~HS
^HT
~HU
^HV Host Query Examples Host Status Return Host Linked Fonts List Return ZebraNet Alert Configuration Host Verification
^HW Host Directory List
^HY
^HZ
^ID
^IL
^IM
^IS
~JA
^JB
~JB
~JC
~JD
~JE
~JF
~JG
^JH Upload Graphics Display Description Information Object Delete Image Load Image Move Image Save Cancel All Initialize Flash Memory Reset Optional Memory Set Media Sensor Calibration Enable Communications Diagnostics Disable Diagnostics Set Battery Condition Graphing Sensor Calibration Early Warning Settings 58 Tally Dascom DL-210 User Guide V1.2 Commands Function
^JI
~JI
^JJ
~JL Start ZBI (Zebra BASIC Interpreter) Start ZBI (Zebra BASIC Interpreter) Set Auxiliary Port Set Label Length
^JM Set Dots per Millimeter
~JN
~JO
~JP
~JQ
~JR
^JS
~JS
^JT
^JU
^JW
~JX
^JZ
~KB
^KD
^KL
^KN
^KV
^LF
^LH
^LL
^LR
^LS
^LT
^MA
^MC
^MD
^MF
^ML Head Test Fatal Head Test Non-Fatal Pause and Cancel Format Terminate Zebra BASIC Interpreter Power On Reset Sensor Select Change Backfeed Sequence Head Test Interval Configuration Update Set Ribbon Tension Cancel Current Partially Input Format Reprint After Error Kill Battery (Battery Discharge Mode) Select Date and Time Format (for Real Time Clock) Define Language Define Printer Name Kiosk Values List Font Links Label Home Label Length Label Reverse Print Label Shift Label Top Set Maintenance Alerts Map Clear Media Darkness Media Feed Maximum Label Length
^MM Print Mode 59 Tally Dascom DL-210 User Guide V1.2 Commands Function
^MN
^MP
^MT
^MU Media Tracking Mode Protection Media Type Set Units of Measurement
^MW Modify Head Cold Warning
^NC
~NC
^ND
^NI
~NR
^NS
~NT
^PA
^PF Select the Primary Network Device Network Connect Change Network Settings Network ID Number Set All Network Printers Transparent Change Wired Networking Settings Set Currently Connected Printer Transparent Advanced Text Properties Slew Given Number of Dot Rows
^PH ~PH Slew to Home Position
~PL
^PM
^PN
^PO Present Length Addition Printing Mirror Image of Label Present Now Print Orientation
^PP ~PP Programmable Pause
^PQ
^PR
~PR
~PS
^PW
~RO
^SC
~SD
^SE
^SF
^SI
^SN
^SP
^SQ Print Quantity Print Rate Applicator Reprint Print Start Print Width Reset Advanced Counters Set Serial Communications Set Darkness Select Encoding Table Serialization Field (with a Standard ^FD String) Set Sensor Intensity Serialization Data Start Print Halt ZebraNet Alert 60 Tally Dascom DL-210 User Guide V1.2 Commands Function
^SR
^SS
^SZ
^TB
^TO
~WC
^WD
~WQ
~WQ
^XA
^XB
^XF
^XG
^XS
^XZ
^ZZ Set Print head Resistance Set Media Sensors Set ZPL Text Blocks Transfer Object Print Configuration Label Print Directory Label Write Query Examples Start Format Suppress Backfeed Recall Format Recall Graphic Set Dynamic Media Calibration End Format Printer Sleep 61 Tally Dascom DL-210 User Guide V1.2 Appendix: Installing the Cutter Disintall the Tear Bar
(1) Turn off the printer power and open the top cover and the print head mechanism, and then pull the tear bar to your side.
(2) Lift the tear bar up and it can be easily removed. 62 Tally Dascom DL-210 User Guide V1.2
(3) The tear bar is removed. Note: Do it in reverse steps so as to install the tear bar. Install the Auto Cutter
(1) Plug in the cutter connector to the printer. 63 Tally Dascom DL-210 User Guide V1.2
(2) Put the auto cutter onto the slot of the low casing.
(3) Move the auto cutter gently to the reverse board till you hear the click sound. 64 Tally Dascom DL-210 User Guide V1.2
(4) After installation you can use the auto cutter. 65 Tally Dascom DL-210 User Guide V1.2 Appendix: FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
aThis device may not cause harmful interference. bThis device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orientate or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. 66 Appendix: DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent
#29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980 USA Phone:+1 (877) 434 13 77 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House, Priestley Road Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com CHINA JIANGMEN DASCOM COMPUTER PERIPHERALS CO., LTD No. 399, Jinxing Road, Jianghai District, Jiangmen, Guangdong P.R. China www.dascom.com.cn FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. DASCOM 67
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-12-16 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2014-12-16
|
||||
1 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021247903
|
||||
1 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 |
Jiangmen City Guang Dong Province, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
f******@us.tuv.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Z7O
|
||||
1 | Equipment Product Code |
DL2100
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y******** H********
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
0750-********
|
||||
1 | Fax Number |
0750-********
|
||||
1 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Label & Barcode Printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
EMTEK (DONGGUAN) CO.,LTD
|
||||
1 | Name |
S**** L****
|
||||
1 | Telephone Number |
86-76********
|
||||
1 | Fax Number |
86-76********
|
||||
1 |
s******@emtek.com.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC